Search Results

Search found 26928 results on 1078 pages for 'disk image'.

Page 393/1078 | < Previous Page | 389 390 391 392 393 394 395 396 397 398 399 400  | Next Page >

  • Expectations for NTFS file recovery

    - by Fred Hamilton
    Yesterday I booted my XP system, and as I looked up a minute later I saw the light blue screen and tail-end of that pre-boot diskcheck Windows sometimes does if it finds an error (or was previously told to run a diskcheck drung the next boot). I didn't worry about it at the moment... But then I looked at my "scratch" disk, which was a 70% full, 750GB hard disk...and it now looks like it has been freshly formatted. It doesn't have a single file on it, just the hidden "System Volume Information" file and 750GB of freedom from data. I looked at some of the recovery tools from the Free NTFS partition recovery question and decided to try PC INSPECTOR™ File Recovery 4.x initially. It ran overnight and afterwards returned a list of thousands of files it could recover. The odd thing was that the filenames were lost, but the file extensions were not (WTF?). And all of the files were exactly 1,472kB in size. I recovered a dozen PDFs as a test, and 80% of them displayed OK despite being padded out to 1.5MB (though I assume any files 1472kB are hosed). My primary question is: Is this the best I can expect from any file recovery software when trying to recover NTFS files? Or is there perhaps something better out there? I assume this is as good as it gets, but wanted to check in with the experts first. Bonus questions: What might have happened to my drive? I didn't intentionally format it. I've never seen a disk error cause the drive to suddenly become a clean, reformatted drive. Could some malicious/confused software have told my PC to format my disk on reboot? Is that even a function Windows XP has? Why can the file extensions be recovered but not the filename? Does NTFS really treat them as separate entities? I thought I had 8.3 naming turned off, but maybe that had something to do with it. Or maybe it looks at the data in the file and guesses the extension?

    Read the article

  • How to recycle/reuse/continue Time Machine for a new Mac?

    - by bmargulies
    I have been backing up a MacBook Pro to an external hard disk with Time Machine. I got a new laptop, used the firewire connector to pull the universe across to it, and started it up. It does not want to just pick up where I left off with the backups; it wants to start a new backup sequence and thus I need a ton of additional disk space. Does anyone know a way to force it to just incrementally back up to the existing backup set?

    Read the article

  • How do I create an MBR on a USB stick using DD command line tool

    - by Lana Miller
    Okay I'm trying to create a BOOTABLE Windows7 image on a USB key from a Mac running Lion. My image is .iso format. I tried: sudo dd if=/Users/myusername/Win7.iso of=/dev/disk1 bs=1m And this succeeded in writing the files, except in DISK UTILITY on the mac, it shows the partition type as GUID Partition Table and not 'Master Boor Record'. Booting the key on my Vista computer yields the error "No boot sector on USB Device' From what I can tell, bs=1m in the DD command should have left 1 Megabyte for the boot sector, but for some reason this area of the USB Key is not set up correctly so that it will boot How can I fix this, or correctly use dd to write a bootable cd image such that it is now a bootable usb drive? Note: in the instructions I read about, they recommended renaming my Win7.iso to Win7.dmg before using DD, which made absolutely no sense to me, so I didn't do it. I could try with that step now, but it takes 1.99 hours to write the image to the USB drive so there is a huge penalty to trial and error here. Thank you.

    Read the article

  • Windows 7 setup location

    - by Sayan
    Hi, We have a computer that came pre-installed with Windows 7; we didn't receive an installation disk for that. How would one create a setup installer disk from a machine which has Windows 7? Thanks, Sayan

    Read the article

  • Troubleshooting painfully slow Windows XP boot

    - by shan
    When I reboot my machine, it takes around 10-15 minutes to boot. Tried removing unused programs, disk defragmentation, check disk, but I'm not able to identify the issue. Any ideas to troubleshoot to see whether there is any failure, trying to start a service/program?

    Read the article

  • How to Enable an External USB Hard Drive with Ubuntu

    - by LarsOn
    I'm trying to install a new LaCie Hard Disk design by Neil Poulton 1TB USB 2.0. GParted reports /dev/sda1 (with exclamation mark and key sign) ntfs 1 KiB unallocated 320 MiB /dev/sda2 hfs+ 2.84 MiB unallocated 931.2 GiB When trying to create a partition with Disk Utility it says Daemon is inhibited It seems I can't create the partition that way. Can you recommend how I can proceed? Thank you

    Read the article

  • Cannot assign a letter to a FAT32 partition

    - by Toc
    I have an external hard disk where I have created many partitions to use also in Linux. First two partitions are FAT32. The third is a Truecrypt partition. I cannot assign a letter to the second partition. When I go to Manage disk and right-click on the unassigned partition, most of the options are not enabled. What have I to do to see this partition on my XP PC?

    Read the article

  • Is it possible that solid state drives (or any faster drive) will make common applications faster even if they are cached?

    - by leladax
    I assumed that solid state drives are insignificant after, say, Firefox is fully brought up and no important disk activity after that is going on. However, I wonder if some kind of 'cached from the disk to the CPU' activity is going on that may make solid state drives (or any faster drive) better. Then again, I suspect that may be depended only on the Bus (or some kind of cache memory drives have). Hrm..

    Read the article

  • NetInstall working on some systems, not working on others

    - by cduruk
    Hi, I'm having an issue where my NetInstall setup works on some computers and fails on others. I am not able to diagnose the issue. I created an image of a Mac Mini and then created a NetRestore image using the System Image Utility found on Snow Leopard Server. NetBoot and NFS all seem to be working fine on the server, which is an XServe. Then I select the NetInstall image from the Startup Disk on a machine. On some of the machines, the process works as expected. On some of them, I see the globe icon blink a few times and then the system boots to the regular hard drive. I have captured the tracedump and the system.log logs from the server on both cases where NetInstall seems to work and fail. Here is the link that has all the logs http://gist.github.com/232232 The gist of the failure seems to be from the lack of BSDP DISCOVER in the failure but I'm not able to identify why that exactly is happening. I'd really appreciate any help on this issue.

    Read the article

  • What if I dismount main volume, where the Windows is installed

    - by ST3
    I'm writing permanent file deletion tool and accessing raw disk clusters. Since Windows Vista writing into raw disk is a bit more complicated. I have tried on my external data device first and worked fine, however one of the steps was dismounting of the volume, not sure if it is a good idea to dismount main volume where the Windows are. Want to ask that is possible consequences and if it safe/unsafe/very unsafe.

    Read the article

  • Partition table corrupted (USB flash drive)

    - by 13ren
    It's an 8 GB Patriot thumb drive, which I've used extensively with lots of data. Today, it is detected, but all data is gone: (EDIT at least some data is still there, but the partition table is gone) EDIT @Sathya (thanks) here's the relevant output from sudo fdisk -l: Disk /dev/sdc: 8019 MB, 8019509248 bytes 247 heads, 62 sectors/track, 1022 cylinders Units = cylinders of 15314 * 512 = 7840768 bytes Disk /dev/sdc doesn't contain a valid partition table It looks like it is /dev/sdc, with that 8 GB... and no partition table. I tried to mount /dev/sdc (and then dmesg | tail): /media> sudo mount /dev/sdc mytmp mount: wrong fs type, bad option, bad superblock on /dev/sdc, missing codepage or other error In some cases useful info is found in syslog - try dmesg | tail or so /media> dmesg | tail [ 24.300000] sdc: unknown partition table [ 24.320000] sd 2:0:0:0: Attached scsi removable disk sdc [ 24.370000] usb-storage: device scan complete [ 26.870000] EXT2-fs error (device sdc): ext2_check_descriptors: Block bitmap for group 1 not in group (block 0)! [ 26.870000] EXT2-fs: group descriptors corrupted! [ 50.420000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 50.430000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 50.430000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 5565.470000] EXT2-fs error (device sdc): ext2_check_descriptors: Block bitmap for group 1 not in group (block 0)! [ 5565.470000] EXT2-fs: group descriptors corrupted! EDIT @Col: results from testdisk Disk /dev/sdc - 8013 MB / 7642 MiB - CHS 1022 247 62 Current partition structure: Partition Start End Size in sectors Partition sector doesn't have the endmark 0xAA55 After I hit [proceed], it says: Structure: Ok. Keys A: add partition, L: load backup, Enter: to continue The "Structure: Ok." seems reassuring... will "A: add partition" make my old data accessible (if it's still there), or will it make a new, fresh partition? Another option is "[ MBR Code ] Write TestDisk MBR code to first sector" - would it be better to do this? EDIT I found that at least some of my data is still on the flash drive, by using the below, and searching for English text in less (like " the "): cat /dev/sde | tr -cd '\11\12\40\1540-\176' | less (The drive changed from "/dev/sdb" to "/dev/sde" because I connected some extra drives today). I've learnt that "/dev/sde1" would be the first partition; and "/dev/sde" is the whole drive. Because unix treats these devices just like files, you can use all the ordinary unix file commands on them, like cat, and then process them like any other stream of data. The tr above removes non-printable characters ("\40" is space, which I wanted to preserve). In less, you can use "/" to search, similar to Vim. How can I get my data back (assuming it's still there)? If only the partition table is corrupted, is there a standard "partition recovery tool"? Is there a way to "repartition" without deleting everything?

    Read the article

  • Unable to use BootCamp to Install Windows 7 on my Macbook Pro

    - by Sheehan Alam
    I get the error: cannot complete the partitioning because some files cannot be moved. I have more than enough space (250GB harddrive, 150GB free) I have tried doing a full defrag with iDefrag I don't want to reformat my drive I have tried partitioning in safe mode I have repaired all Disk Permissions using Disk Utility Any suggestions? NOTE: I am installing Windows 7 64-bit I am trying to create a 32GB partition

    Read the article

  • flashcache with mdadm and LVM

    - by Backtogeek
    I am having trouble setting up flashcache on a system with LVM and mdadm, I suspect I am either just missing an obvious step or getting some mapping wrong and hoped someone could point me in the right direction? system info: CentOS 6.4 64 bit mdadm config md0 : active raid1 sdd3[2] sde3[3] sdf3[4] sdg3[5] sdh3[1] sda3[0] 204736 blocks super 1.0 [6/6] [UUUUUU] md2 : active raid6 sdd5[2] sde5[3] sdf5[4] sdg5[5] sdh5[1] sda5[0] 3794905088 blocks super 1.1 level 6, 512k chunk, algorithm 2 [6/6] [UUUUUU] md3 : active raid0 sdc1[1] sdb1[0] 250065920 blocks super 1.1 512k chunks md1 : active raid10 sdh1[1] sda1[0] sdd1[2] sdf1[4] sdg1[5] sde1[3] 76749312 blocks super 1.1 512K chunks 2 near-copies [6/6] [UUUUUU] pcsvan PV /dev/mapper/ssdcache VG Xenvol lvm2 [3.53 TiB / 3.53 TiB free] Total: 1 [3.53 TiB] / in use: 1 [3.53 TiB] / in no VG: 0 [0 ] flashcache create command used: flashcache_create -p back ssdcache /dev/md3 /dev/md2 pvdisplay --- Physical volume --- PV Name /dev/mapper/ssdcache VG Name Xenvol PV Size 3.53 TiB / not usable 106.00 MiB Allocatable yes PE Size 128.00 MiB Total PE 28952 Free PE 28912 Allocated PE 40 PV UUID w0ENVR-EjvO-gAZ8-TQA1-5wYu-ISOk-pJv7LV vgdisplay --- Volume group --- VG Name Xenvol System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 2 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 1 Max PV 0 Cur PV 1 Act PV 1 VG Size 3.53 TiB PE Size 128.00 MiB Total PE 28952 Alloc PE / Size 40 / 5.00 GiB Free PE / Size 28912 / 3.53 TiB VG UUID 7vfKWh-ENPb-P8dV-jVlb-kP0o-1dDd-N8zzYj So that is where I am at, I thought that was the job done however when creating a logical volume called test and mounting it is /mnt/test the sequential write is pathetic, 60 ish MB/s /dev/md3 has 2 x SSD's in Raid0 which alone is performing at around 800 MB/s sequential write and I am trying to cache /dev/md2 which is 6 x 1TB drives in raid6 I have read a number of pages through the day and some of them here, it is obvious from the results that the cache is not functioning but I am unsure why. I have added the filter line in the lvm.conf filter = [ "r|/dev/sdb|", "r|/dev/sdc|", "r|/dev/md3|" ] It is probably something silly but the cache is clearly performing no writes so I suspect I am not mapping it or have not mounted the cache correctly. dmsetup status ssdcache: 0 7589810176 flashcache stats: reads(142), writes(0) read hits(133), read hit percent(93) write hits(0) write hit percent(0) dirty write hits(0) dirty write hit percent(0) replacement(0), write replacement(0) write invalidates(0), read invalidates(0) pending enqueues(0), pending inval(0) metadata dirties(0), metadata cleans(0) metadata batch(0) metadata ssd writes(0) cleanings(0) fallow cleanings(0) no room(0) front merge(0) back merge(0) force_clean_block(0) disk reads(9), disk writes(0) ssd reads(133) ssd writes(9) uncached reads(0), uncached writes(0), uncached IO requeue(0) disk read errors(0), disk write errors(0) ssd read errors(0) ssd write errors(0) uncached sequential reads(0), uncached sequential writes(0) pid_adds(0), pid_dels(0), pid_drops(0) pid_expiry(0) lru hot blocks(31136000), lru warm blocks(31136000) lru promotions(0), lru demotions(0) Xenvol-test: 0 10485760 linear I have included as much info as I can think of, look forward to any replies.

    Read the article

  • converting a png with an ICC profile?

    - by jedierikb
    I can convert a jpg from one ICC to another ICC. convert rgb_image.jpg -profile USCoat.icm cmyk_image.jpg Or I can convert a jpg with no ICC to another ICC. convert rgb_image.jpg +profile icm \ -profile sRGB.icc -profile USCoat.icm cmyk_image.jpg But how do I convert a png's pixels into the gamut described by an ICC profile? I understand I cannot embed the profile into the image file, but would at least like to convert the colors. When I reuse the above commands, the colors come out wrong... (different from the colors in the JPG when converted). This is the source image: http://alumni.media.mit.edu/~erikb/tmp/RED_JPG.jpg And here is what I am trying: convert RED_JPG.jpg +profile icm -profile sRGB_v4_ICC_preference.icc -profile USWebUncoated.icc CMYK_PNG.png and this is what I am getting: http://alumni.media.mit.edu/~erikb/tmp/CMYK_PNG.png I was hoping to get an image with the same colors as a JPEG run through the same command: convert RED_JPG.jpg +profile icm -profile sRGB_v4_ICC_preference.icc -profile USWebUncoated.icc CMYK_JPG.jpg resulting in: http://alumni.media.mit.edu/~erikb/tmp/CMYK_JPG.jpg *this image, CMYK_JPG.jpg, is what I am trying to reproduce pixel by pixel in a PNG file.* Any suggestions? Original (unanswered) post here.

    Read the article

  • How To Replace Laptop HDD Without Losing Data?

    - by Ishan
    Hello, I recently went to Dell Service center and they tell that HDD is faulty and needs to be replaced. I have a Studio 1457 laptop with 500 GB HDD and don't want to lose the data(purchased in May 2010, still under warranty). I have searched a bit and I think it may be best to use a disk imaging software for this task. However, I don't know about a good software. I have following steps in mind: Get a 1 TB External HDD. Make an image of existing 500 GB HDD and store data on external disk. Install new HDD and install a brand new Windows copy and then install the software on it. Using the same software I used to make image, restore the old HDD image on new one. However, I have some questions in mind. First, is this possible? Second, I live in a country where piracy is a big issue and I am sure the support executive who will come to change HDD will have a pirated copy. But I have genuine Windows 7 Pro and don't want to lose it. Now, Dell does not supply and OS disks, so I can't install it on new HDD! If I follow above steps, which version of Windows 7 will be retained? One in the image(authentic) or one in the new HDD(pirated). I am ready to purchase a good software for this task and my budget is $50-60. Since laptop is under warranty, new HDD will be free. One last thing, I have created a Windows Migration file whose size is 70 GB. Can it be used to move from Windows 7 Pro to Windows 7 Pro?(In case I get a genuine copy of Windows 7!) Any other method to save all the data? Thanks in advance.

    Read the article

  • windows 2008 Cannot extend volume for c

    - by user29266
    Hello, I have a 150 GB hard drive on a windows 2008 server. 87 GB partition for D:\ 10 GB partition for C:\ I cannot extend/increase the partition for C:\ in the disk manager utility. as described here: http://www.howtogeek.com/howto/windows-vista/resize-a-partition-for-free-in-windows-vista/ I tried doing it through the command: http://www.winvistaclub.com/t11.html However I got the error: There is not enough space available on the disk(s) to complete this operation.

    Read the article

  • Ram question in VMware Server 2

    - by ToreTrygg
    Hi, I understand from the VMware Server 2 documentation that VMware Server 2 is capable of running a 64-bit guest OS underneath a 32-bit host OS, as long as the hardware running the box is 64-bit capable. Here's my situation. We currently have an underutilized XEON X3220 Quad Core 64bit Server, running Server 2003, 32-bit and 2gb of RAM (the motherboard is capable of 8gb ram). The server is currently used mainly for file and print services. It is also running Active Directory, Novell eDirectory and Groupwise 6.5. We are planning a micration to Microsoft Exchange, so the Novell eDirectory and Groupwise services will eventually be purged from this box, leaving only Active Directory, File and Print services. Being that this server is underutilized we are hoping to save hardware costs and virtualize our new Exchange investment. My question is this. Will VMware allow access to the "invisible" extra memory that Windows 32-bit won't see. Meaning, if we increase the full amount of system ram to 8gb (yes, I know the 32-bit host OS will only see a maximum of 4gb), will I be able to assign maybe 5gb to the new Server 2008 64-bit OS running Exchange and leave 3gb for the Guest OS (or maybe even a 6, 2 split). The second part of that would be, would it be better to just convert the main OS currently running to an image, convert the machine itself to ESXi and run both OSes as images under ESXi. Downtime for this box is critical, so my preference is most definitly with the first option because it presents very minimal downtime. Doing the second would make downtime quite a few hours to image the machine and then convert the image to a VMware Image.

    Read the article

  • Using NFS for scalable PHP/MySQL web application

    - by Jeroen Moons
    Here's the situation: I have a PHP/MySQL web application that accepts user uploads (pdf files). From these pdf files' pages a preview image is made on the fly and presented to the web app's users. Some pdfs might be on the large side, most will be under 50 MB but some extreme cases could be as large as a few hundred MB. A little waiting for the preview image for large pdf files is acceptable but no more than a minute let's say. Everything is running on one server for now, but soon the app will hit the server's limit on both storage and processing power. My idea to solve the problem: To deal with this situation I had the idea of having one or more pdf processing servers as needed, and one or more file storage servers. These two types of servers are mounted to the server on which the actual app runs using NFS. The app could then use GearMan to delegate pdf processing tasks to these processing servers. The processing server can mount the storage server and read the file stored there, process it and write its output to that server. The servers I'm talking about will be amazon ec2 instances. The web app returns a link to the resulting pdf preview image on the storage server that was used which can then be used on the front end to show the image to the user. My question: I have zero experience with apps that use multiple servers, is this idea viable or is there a better way to do it? Is an NFS setup fast and reliable enough for this situation?

    Read the article

  • Why is Outlook 2007 resizing images in outgoing and incoming HTML email? How can I fix this?

    - by Mikuso
    In my Outlook 2007 client, embedded images in incoming emails appear resized when the message is viewed. The incoming images are resized to 198px wide, despite the original size. If it was larger, it will be shrunk; if it was smaller, it will be enlarged; the aspect ratio remains the same (the image is not stretched). This is local to my client only (i.e. another Outlook 2007 client reading the same IMAP inbox will see the image in the correct size. Similarly, viewing the email message in a browser will display the correct size). This happens regardless of whether width/height attributes are set on the image tag in the HTML. Zoom is set to 100% in my message window; text and other elements are not distorted from the original. In addition to this, outgoing HTML messages with images embedded in the same way are resized as they are sent. The outgoing images are all scaled to have a width of 247px. The source HTML of the outgoing message is changed after pressing Send so that the tag's width attribute is 247 pixels and the image file itself is also resized. These problems only occur with HTML messages; Rich Text messages do not have the same problem. I have already tried reinstalling Outlook and have it fully patched up to date. Why is this happening and how can I stop this?

    Read the article

  • Want to use something like Citrix XenDesktop, Free Alternative?

    - by Chris
    I'm looking to go into IT, general office server management, and it looks like XenDesktop would be a awesome tool to use. If I get it right, you would store a central image of the OS you want to deploy (in an iso file) on the main server. Then use XenDesktop to pull that image down to the client, and it will then boot the OS inside of the virtual machine. Does it download the image of the OS and store it locally (like cloning the VM onto the client?) I'd love to find a free (possibly open source?) alternative to this, I keep on hearing about KVM in Linux and PXE booting a minimalistic OS to use remote KVMs.... Would that be what I'm looking for? Ideally, I'd like a system.. - That allows me to manage one central image for multiple clients (virtualized hardware) - Easily boot a thin client OS that connected to XenDesktop. Would those things be possible with some kind of free alternative? Some guidance would be greatly appreciated.

    Read the article

  • Grub Solaris FreeBSD dual boot

    - by pallavt
    I have solaris 10 installed on the first hard disk and freebsd installed on the second hard disk I edited the /boot/grub/menu.lst from solaris to the following title FreeBSD root (hd1,0) kernel /boot/loader Now when I try to boot into freebsd via the grub, it gives the following error root (hd1,0) Filesystem type unknown, partition type 0xee kernel /boot/loader Error 17: cannot mount selected partition

    Read the article

  • Why does writing a file to an NFS share send a COMMIT operation to the NFS server?

    - by Antonis Christofides
    I have a Debian squeeze (2.6.32-5-amd64) which is at the same time a NFS4 server and client (it mounts itself through NFS4). The local directory that leads directly to disk is /nfs4exports/mydir, whereas /nfs4mounts/mydir is the same thing mounted through NFS, using the machine's external IP address. Here is the line from fstab: 192.168.1.75:/mydir /nfs4mounts/mydir nfs4 soft 0 0 I have an application that writes many small files. If I write directly to /nfs4exports/mydir, it writes thousands of files per second; but if I write to /nfs4mounts/mydir, it writes 4 files per second or so. I can greatly increase speed if I add async to /etc/exports. (Writing a single large file to the NFS-mounted directory goes at more than 100 MB/s.) I examine the server statistics and I see that whenever a file is written, it is "committed" (this also happens with NFSv3): root@debianvboxtest:~# mount -t nfs4 192.168.1.75:/mydir /mnt root@debianvboxtest:~# nfsstat|grep -A 2 'nfs v4 operations' Server nfs v4 operations: op0-unused op1-unused op2-future access close commit 0 0% 0 0% 0 0% 10 4% 1 0% 1 0% root@debianvboxtest:~# echo 'hello' >/mnt/test1056 root@debianvboxtest:~# nfsstat|grep -A 2 'nfs v4 operations' Server nfs v4 operations: op0-unused op1-unused op2-future access close commit 0 0% 0 0% 0 0% 11 4% 2 0% 2 0% Now in the RFC, I read this: The COMMIT operation is similar in operation and semantics to the POSIX fsync(2) system call that synchronizes a file's state with the disk (file data and metadata is flushed to disk or stable storage). COMMIT performs the same operation for a client, flushing any unsynchronized data and metadata on the server to the server's disk or stable storage for the specified file. I don't understand why the client commits. I don't think that the "echo" shell built-in command runs fsync; if echo wrote to a local file and then the machine went down, the file might be lost. In contrast, the NFS client appears to be sending a COMMIT upon completion of the echo. Why? I am reluctant to use the async NFS server option, because it would apparently ignore COMMIT. I feel as if I had a local filesystem and I had to choose between syncing every file upon close and ignoring fsync altogether. What have I understood wrong?

    Read the article

  • Recover harddrive data

    - by gameshints
    I have a dell laptop that recently "died" (It would get the blue screen of death upon starting) and the hard drive would make a weird cyclic clicking noises. I wanted to see if I could use some tools on my linux machine to recover the data, so I plugged it into there. If I run "fdisk" I get: Disk /dev/sdb: 20.0 GB, 20003880960 bytes 64 heads, 32 sectors/track, 19077 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Disk identifier: 0x64651a0a Disk /dev/sdb doesn't contain a valid partition table Fine, the partition table is messed up. However if I run "testdisk" in attempt to fix the table, it freezes at this point, making the same cyclical clicking noises: Disk /dev/sdb - 20 GB / 18 GiB - CHS 19078 64 32 Analyse cylinder 158/19077: 00% I don't really care about the hard drive working again, and just the data, so I ran "gpart" to figure out where the partitions used to be. I got this: dev(/dev/sdb) mss(512) chs(19077/64/32)(LBA) #s(39069696) size(19077mb) * Warning: strange partition table magic 0x2A55. Primary partition(1) type: 222(0xDE)(UNKNOWN) size: 15mb #s(31429) s(63-31491) chs: (0/1/1)-(3/126/63)d (0/1/32)-(15/24/4)r hex: 00 01 01 00 DE 7E 3F 03 3F 00 00 00 C5 7A 00 00 Primary partition(2) type: 007(0x07)(OS/2 HPFS, NTFS, QNX or Advanced UNIX) (BOOT) size: 19021mb #s(38956987) s(31492-38988478) chs: (4/0/1)-(895/126/63)d (15/24/5)-(19037/21/31)r hex: 80 00 01 04 07 7E FF 7F 04 7B 00 00 BB 6F 52 02 So I tried to mount just to the old NTFS partition, but got an error: sudo mount -o loop,ro,offset=16123904 -t ntfs /dev/sdb /mnt/usb NTFS signature is missing. Ugh. Okay. But then I tried to get a raw data dump by running dd if=/dev/sdb of=/home/erik/brokenhd skip=31492 count=38956987 But the file got up to 59885568 bytes, and made the same cyclical clicking noises. Obviously there is a bad sector, but I don't know what to do about it! The data is still there... if I view that 57MB file in textpad... I can see raw data from files. How can I get my data back? Thanks for any suggestions, Solution: I was able to recover about 90% of my data: Froze harddrive in freezer Used Ddrescue to make a copy of the drive Since Ddrescue wasn't able to get enough of my drive to use testdisk to recover my partitions/file system, I ended up using photorec to recover most of my files

    Read the article

  • Recovering files using Recuva

    - by Nev Meek
    I'm currently using Recuva to recover some files from an external NTFS disk. It finds the files I'm interested in during it's analysis phase (when tools like test-disk fail to find them at all) and reports them as "Not-deleted" and a big green marker to signify 100% chance of recovery. However when it tries to recover the files I get a "the system could not find the file specified" message. Is there any easy way to recover non-deleted files off of a disc that I can no longer simply access through explorer?

    Read the article

< Previous Page | 389 390 391 392 393 394 395 396 397 398 399 400  | Next Page >