Search Results

Search found 13180 results on 528 pages for 'non interactive'.

Page 396/528 | < Previous Page | 392 393 394 395 396 397 398 399 400 401 402 403  | Next Page >

  • Simple options for port forwarding to a different port?

    - by Nick
    I have three network printers at our local office, all of which listen on port 9100. Non of them offer the option of changing the listening port. We have a single public static IP address, and access to our main network is through a Linksys WRT-54G. We need to be able to print to these printers from outside the office. The problem is, with the 54G, I can only forward a port to the SAME port on a particular IP address. What I really need though is a way to forward to an ip address and a DIFFERENT port. I need to do this: In port Destination 9100 192.168.1.1 : 9100 9101 192.168.1.2 : 9100 9102 192.168.1.3 : 9100 So I'm looking for options. I could setup an old computer with two network cards and IPtables I suppose, but that seems like a lot of overhead for something relatively simple. Is there a way a virtual machine (read: one network card) could do the advanced port forwarding? Where I forward all traffic to it, and it forwards it on to the right printer? Or what about those mini Linux distros that replace the WRT-54G's firmware? Do any of those support what I need "out of the box"? I have a spare WRT- could I make it an IP tables router? Recommendations for mini distros? Or is there an off-the-shelf product that does this (cheap/local preferred)? Any advice / options appreciated. Thanks!

    Read the article

  • IIS 7.5 Siteminder is not protecting ASP.net MVC requests

    - by HariM
    We are trying to use ASP.Net MVC with Siteminder for Single Sign on. This is on Windows Server 2008 R2 with IIS 7.5. Siteminder Agent version 6QMR6. Problem : Siteminder protects physical files that are exist. And it is not protecting the folder when we try to access a non existed file. It must redirect to login page even if the file doesn't exist when the user is accessing a protected folder. How to configure in IIS 7.5 that Do not verify a file exist, before authentication by siteminder. SiteMinderWebAgent is a Handler(WildCard Script Map) we created using the ISAPI6WebAgent.dll How to Protect ASP.Net MVC Request with Siteminder? (Added this as My previous question did not solve the problem). MVC Request shows up in IIS Log but not in Siteminder log. Update : Microsoft Support says currently IIS7.5, even in earlier versions doesnt support wildcard mappings on any two Isapi Handlers with * wild card. Currently in my case Siteminder has * wildcard and asp.net mvc (handler is aspnet_isapi) has * wildcard to handle the reqeusts. Ordered priority doesnt work in the wild card mappings case with Just *. Did not convinced with the answer but will wait till tomorrow for them to get back.

    Read the article

  • HP Pavillion DV6500 recovery disk failure

    - by Scott W
    I recently attempted to re-install Windows Vista on an HP Pavillion DV6500 using the factory recovery DVD's, but encountered a strange problem. When the recovery disk attempted to reformat the hard disk, it failed at 22%. The error message provided was not very informative, just the error code "0x400110020000 1005". A google search turned up some people with a similar problem who asserted that HP has been know to ship corrupted recovery DVDs. The recovery disk did manage to reformat the the recovery partition before failing though, so recovering from the partition is no longer an option. It would be possible to reinstall from an off-the-shelf retail copy of Vista and then pull the drivers from HP's website, but I don't have access to a copy of Vista, and it would really be outrageous to have to purchase a new OS when I have a perfectly valid license already. Thought about biting the bullet and upgrading to Windows 7, but my understanding is that without Vista installed I'd be unable to use the upgrade version, and be forced to purchase the more expensive non-upgrade retail copy (!). Can anyone suggest a possible solution to this Catch-22? I've run out of ideas.

    Read the article

  • Linux: How do I remove bootchart from the boot process?

    - by java.is.for.desktop
    Hello, everyone! I have OpenSUSE 11.2. I removed bootchart and forgot to run mkinitrd. Now, right at the start of the boot process, I get boot/93-bootchart.sh: line 17: 462 Terminated stopinitrd 5 I Can't find any 93-bootchart.sh anywhere. Failsafe boot mode doesn't help. Earlier I got an error message about non existing /sbin/bootchartd, but I just copied /bin/cat to /sbin/bootchartd using a GParted boot disk. I tried to use chroot with an OpenSUSE boot disk, but mkinitrd can't find the root device, which is there actually (/dev/sda5). How can I make my system boot again? EDIT Ok, now I managed to re-install the bootchart rpm, using OpenSUSE boot disk and chmod. The system starts again. But that annoying bootchart is still there. I will not try again to remove it. First I will try to figure out, how to disable it during the boot process. Hopefully with your help ;)

    Read the article

  • Server error 500: Undefinable problem with my Zend Framework based site

    - by sanders
    Hello everyone, Lately I had to reinstall my development site on my ubuntu machine since my system crashed after an os update. 4 days later my site is still not running as it should. Whenever i do an action which has in it an action on a database, it stops working. For example when Registring a new user, i get the following error: [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP Notice: Trying to get property of non-object in /var/www/nrka2/application/bootstrap/Bootstrap.php on line 169, referer: http://nrka2/user/register [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP Stack trace:, referer: http://nrka2/user/register [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP 1. {main}() /var/www/nrka2/public/index.php:0, referer: http://nrka2/user/register [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP 2. require() /var/www/nrka2/public/index.php:2, referer: http://nrka2/user/register [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP 3. Zend_Application->bootstrap() /var/www/nrka2/application/application.php:23, referer: http://nrka2/user/register [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP 4. Zend_Application_Bootstrap_BootstrapAbstract->bootstrap() /var/www/Zend/ZendFramework-1.10.6/library/Zend/Application.php:355, referer: http://nrka2/user/register [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP 5. Zend_Application_Bootstrap_BootstrapAbstract->_bootstrap() /var/www/Zend/ZendFramework-1.10.6/library/Zend/Application/Bootstrap/BootstrapAbstract.php:583, referer: http://nrka2/user/register [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP 6. Zend_Application_Bootstrap_BootstrapAbstract->_executeResource() /var/www/Zend/ZendFramework-1.10.6/library/Zend/Application/Bootstrap/BootstrapAbstract.php:619, referer: http://nrka2/user/register [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP 7. Bootstrap->_initViewSettings() /var/www/Zend/ZendFramework-1.10.6/library/Zend/Application/Bootstrap/BootstrapAbstract.php:666, referer: http://nrka2/user/register [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP Notice: Trying to get property of non-object in /var/www/nrka2/application/bootstrap/Bootstrap.php on line 169, referer: http://nrka2/css/main.css [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP Stack trace:, referer: http://nrka2/css/main.css [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP 1. {main}() /var/www/nrka2/public/index.php:0, referer: http://nrka2/css/main.css [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP 2. require() /var/www/nrka2/public/index.php:2, referer: http://nrka2/css/main.css [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP 3. Zend_Application->bootstrap() /var/www/nrka2/application/application.php:23, referer: http://nrka2/css/main.css [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP 4. Zend_Application_Bootstrap_BootstrapAbstract->bootstrap() /var/www/Zend/ZendFramework-1.10.6/library/Zend/Application.php:355, referer: http://nrka2/css/main.css [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP 5. Zend_Application_Bootstrap_BootstrapAbstract->_bootstrap() /var/www/Zend/ZendFramework-1.10.6/library/Zend/Application/Bootstrap/BootstrapAbstract.php:583, referer: http://nrka2/css/main.css [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP 6. Zend_Application_Bootstrap_BootstrapAbstract->_executeResource() /var/www/Zend/ZendFramework-1.10.6/library/Zend/Application/Bootstrap/BootstrapAbstract.php:619, referer: http://nrka2/css/main.css [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP 7. Bootstrap->_initViewSettings() /var/www/Zend/ZendFramework-1.10.6/library/Zend/Application/Bootstrap/BootstrapAbstract.php:666, referer: http://nrka2/css/main.css My Bootstrap class looks like this: <?php class Bootstrap extends Zend_Application_Bootstrap_Bootstrap{ /** * * @var unknown_type */ public $frontcontroller; /** * * @var unknown_type */ protected $_logger; /** * * @var unknown_type */ protected $_acl; /** * * @var unknown_type */ protected $_auth; /** * Setup the logging */ protected function _initLogging() { $this->bootstrap('frontController'); $logger = new Zend_Log(); $writer = 'production' == $this->getEnvironment() ? new Zend_Log_Writer_Stream(APPLICATION_PATH . '/../data/logs/app.log') : new Zend_Log_Writer_Firebug(); $logger->addWriter($writer); if ('production' == $this->getEnvironment()) { $filter = new Zend_Log_Filter_Priority(Zend_Log::CRIT); $logger->addFilter($filter); } $this->_logger = $logger; Zend_Registry::set('log', $logger); } protected function _initDefaultModuleAutoloader(){ $this->_logger->info('Bootstrap '. __METHOD__); $this->_resourceLoader = new Zend_Application_Module_Autoloader(array( 'namespace' => 'EventManager', 'basePath' => APPLICATION_PATH . '/modules/eventManager', )); $this->_resourceLoader->addResourceTypes(array( 'modelResource' => array( 'path' => 'models/resources', 'namespace' => 'Resource', ), 'service' => array( 'path' => 'services', 'namespace' => 'Service' ), )); } // @todo develop this function protected function _initDbProfiler(){ $this->_logger->info('Bootstrap ' . __METHOD__); if ('production' !== $this->getEnvironment()) { $this->bootstrap('db'); $profiler = new Zend_Db_Profiler_Firebug('All DB Queries'); $profiler->setEnabled(true); $this->getPluginResource('db')->getDbAdapter()->setProfiler($profiler); } } /** * Add Controller Action Helpers */ protected function _initActionHelpers() { $this->_logger->info('Bootstrap ' . __METHOD__); Zend_Controller_Action_HelperBroker::addHelper(new SF_Controller_Helper_Acl()); Zend_Controller_Action_HelperBroker::addHelper(new SF_Controller_Helper_RedirectCommon()); Zend_Controller_Action_HelperBroker::addHelper(new SF_Controller_Helper_Service()); } /** * * @return unknown_type */ protected function _initRoutes(){ $this->_logger->info('Initialize Routes '. __METHOD__); $this->bootstrap('frontController'); $router = $this->frontController->getRouter(); $route = new Zend_Controller_Router_route( 'register', array( 'controller' => 'user', 'action' => 'register' ) ); $router->addRoute('register',$route); $route = new Zend_Controller_Router_route( 'login', array( 'controller' => 'user', 'action' => 'login' ) ); $router->addRoute('login',$route); $route = new Zend_Controller_Router_route( 'logout', array( 'controller' => 'user', 'action' => 'logout' ) ); $router->addRoute('logout',$route); } /** * * @return void */ protected function _initLocale(){ $this->_logger->info('Bootstrap '.__METHOD__); $locale = new Zend_Locale('nl_NL'); Zend_Registry::set('Zend_Locale', $locale); } protected function _initAcl(){ $this->_acl = new EventManager_Service_Acl(); } /** * * @return void */ protected function _initViewSettings(){ $this->_logger->info('Bootstrap '.__METHOD__); $this->bootstrap('view'); $this->bootstrap('Acl'); $this->_view = $this->getResource('view'); //set encoding and doctype $this->_view->setEncoding('UTF-8'); $this->_view->doctype('XHTML1_STRICT'); $this->_view->headMeta()->appendHttpEquiv('Content-Type', 'text/html; charset=UTF-8'); $this->_view->headMeta()->appendHttpEquiv('Content-Language', 'en-US'); //@todo op een later moment moeten hier nog de stylesheets worden toegevoegd $this->_view->headLink()->appendStylesheet('/css/main.css'); //$this->_view->headTitle('Event Manager'); /* Set the head style. $this->_view->headTitle->headStyle(); */ $this->_view->headTitle()->setSeparator(' - '); $this->_auth = Zend_Auth::getInstance(); $navigation = new Zend_Config_Xml(APPLICATION_PATH.'/configs/navigation.xml','nav'); $navContainer = new Zend_Navigation($navigation); $this->_view->navigation($navContainer)->setAcl($this->_acl)->setRole($this->_auth->getStorage()->read()->usr_role); //THIS IS LINE 169!!!!!!!!! } /** * Add graceful error handling to the dispatch, this will handle * errors during Front Controller dispatch. */ public function run() { $errorHandling = $this->getOption('errorhandling'); try { parent::run(); } catch(Exception $e) { if (true == (bool) $errorHandling['graceful']) { $this->__handleErrors($e, $errorHandling['email']); } else { throw $e; } } } /** * Handle errors gracefully, this will work as long as the views, * and the Zend classes are available * * @param Exception $e * @param string $email */ protected function __handleErrors(Exception $e, $email) { header('HTTP/1.1 500 Internal Server Error'); $view = new Zend_View(); $view->addScriptPath(dirname(__FILE__) . '/../views/scripts'); echo $view->render('fatalError.phtml'); if ('' != $email) { $mail = new Zend_Mail(); $mail->setSubject('Fatal error in application Storefront'); $mail->addTo($email); $mail->setBodyText( $e->getFile() . "\n" . $e->getMessage() . "\n" . $e->getTraceAsString() . "\n" ); @$mail->send(); } } } I have tried to debug my code, but everyting goes well until I do somethign with the db. But I don't know what goes wrong with the db. I don't get any clear error messages. Can someone help me? Some more possible interesting data: [bootstrap] resources.db.adapter = "PDO_MYSQL" resources.db.isdefaulttableadapter = true resources.db.params.dbname = "ladosa" resources.db.params.username = "root" resources.db.params.password = "root" resources.db.params.hostname = "localhost" resources.db.params.charset = "UTF8" resources.db.params.profiler.enabled = true resources.db.params.profiler.class = Zend_Db_Profiler_Firebug Autoloadernamespaces[] = "Zend_" Autoloadernamespaces[] = "SF_" phpsettings.display_errors = 0 phpsettings.error_reporting = 8191 phpSettings.date.timezone = "Europe/Amsterdam" bootstrap.path = APPLICATION_PATH"/bootstrap/Bootstrap.php" pluginPaths.resource_ = APPLICATION_PATH"/resources" resources.frontcontroller.moduledirectory = APPLICATION_PATH"/modules" resources.frontcontroller.defaultmodule = "eventManager" resources.frontcontroller.params.prefixDefaultModule = true resources.frontcontroller.exceptions = false resources.view[] = "" resources.layout.layoutPath = APPLICATION_PATH "/layouts/scripts" resources.view.encoding = "UTF-8" resources.view.title = Rode kruis Vrijwilligers applicatie ;resources.view.helperPath.Default_View_Helper = APPLICATION_PATH "/modules/eventManager/views/helpers" resources.layout.layout = "main" [production:bootstrap] [development:bootstrap] ;resources.frontController.throwExceptions = 1 ;phpSettings.display_startup_errors=1 ;phpSettings.display_errors = 1 ;resources.frontcontroller.throwerrors = [test:production] btw. I CAN login to my database command line with the given username and password. Update: today i decided to investigate on my http request and i came to an error 500. My apache logs don't give any related information, I think. I posted the logs above. Any idea's?

    Read the article

  • Server error 500: Undefinable problem with my Zend Framework based site

    - by sanders
    Lately I had to reinstall my development site on my ubuntu machine since my system crashed after an os update. 4 days later my site is still not running as it should. Whenever i do an action which has in it an action on a database, it stops working. For example when Registring a new user, i get the following error: [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP Notice: Trying to get property of non-object in /var/www/nrka2/application/bootstrap/Bootstrap.php on line 169, referer: http://nrka2/user/register [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP Stack trace:, referer: http://nrka2/user/register [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP 1. {main}() /var/www/nrka2/public/index.php:0, referer: http://nrka2/user/register [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP 2. require() /var/www/nrka2/public/index.php:2, referer: http://nrka2/user/register [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP 3. Zend_Application->bootstrap() /var/www/nrka2/application/application.php:23, referer: http://nrka2/user/register [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP 4. Zend_Application_Bootstrap_BootstrapAbstract->bootstrap() /var/www/Zend/ZendFramework-1.10.6/library/Zend/Application.php:355, referer: http://nrka2/user/register [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP 5. Zend_Application_Bootstrap_BootstrapAbstract->_bootstrap() /var/www/Zend/ZendFramework-1.10.6/library/Zend/Application/Bootstrap/BootstrapAbstract.php:583, referer: http://nrka2/user/register [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP 6. Zend_Application_Bootstrap_BootstrapAbstract->_executeResource() /var/www/Zend/ZendFramework-1.10.6/library/Zend/Application/Bootstrap/BootstrapAbstract.php:619, referer: http://nrka2/user/register [Sun Jul 25 20:07:20 2010] [error] [client 127.0.0.1] PHP 7. Bootstrap->_initViewSettings() /var/www/Zend/ZendFramework-1.10.6/library/Zend/Application/Bootstrap/BootstrapAbstract.php:666, referer: http://nrka2/user/register [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP Notice: Trying to get property of non-object in /var/www/nrka2/application/bootstrap/Bootstrap.php on line 169, referer: http://nrka2/css/main.css [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP Stack trace:, referer: http://nrka2/css/main.css [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP 1. {main}() /var/www/nrka2/public/index.php:0, referer: http://nrka2/css/main.css [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP 2. require() /var/www/nrka2/public/index.php:2, referer: http://nrka2/css/main.css [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP 3. Zend_Application->bootstrap() /var/www/nrka2/application/application.php:23, referer: http://nrka2/css/main.css [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP 4. Zend_Application_Bootstrap_BootstrapAbstract->bootstrap() /var/www/Zend/ZendFramework-1.10.6/library/Zend/Application.php:355, referer: http://nrka2/css/main.css [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP 5. Zend_Application_Bootstrap_BootstrapAbstract->_bootstrap() /var/www/Zend/ZendFramework-1.10.6/library/Zend/Application/Bootstrap/BootstrapAbstract.php:583, referer: http://nrka2/css/main.css [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP 6. Zend_Application_Bootstrap_BootstrapAbstract->_executeResource() /var/www/Zend/ZendFramework-1.10.6/library/Zend/Application/Bootstrap/BootstrapAbstract.php:619, referer: http://nrka2/css/main.css [Sun Jul 25 20:07:22 2010] [error] [client 127.0.0.1] PHP 7. Bootstrap->_initViewSettings() /var/www/Zend/ZendFramework-1.10.6/library/Zend/Application/Bootstrap/BootstrapAbstract.php:666, referer: http://nrka2/css/main.css My Bootstrap class looks like this: <?php class Bootstrap extends Zend_Application_Bootstrap_Bootstrap{ /** * * @var unknown_type */ public $frontcontroller; /** * * @var unknown_type */ protected $_logger; /** * * @var unknown_type */ protected $_acl; /** * * @var unknown_type */ protected $_auth; /** * Setup the logging */ protected function _initLogging() { $this->bootstrap('frontController'); $logger = new Zend_Log(); $writer = 'production' == $this->getEnvironment() ? new Zend_Log_Writer_Stream(APPLICATION_PATH . '/../data/logs/app.log') : new Zend_Log_Writer_Firebug(); $logger->addWriter($writer); if ('production' == $this->getEnvironment()) { $filter = new Zend_Log_Filter_Priority(Zend_Log::CRIT); $logger->addFilter($filter); } $this->_logger = $logger; Zend_Registry::set('log', $logger); } protected function _initDefaultModuleAutoloader(){ $this->_logger->info('Bootstrap '. __METHOD__); $this->_resourceLoader = new Zend_Application_Module_Autoloader(array( 'namespace' => 'EventManager', 'basePath' => APPLICATION_PATH . '/modules/eventManager', )); $this->_resourceLoader->addResourceTypes(array( 'modelResource' => array( 'path' => 'models/resources', 'namespace' => 'Resource', ), 'service' => array( 'path' => 'services', 'namespace' => 'Service' ), )); } // @todo develop this function protected function _initDbProfiler(){ $this->_logger->info('Bootstrap ' . __METHOD__); if ('production' !== $this->getEnvironment()) { $this->bootstrap('db'); $profiler = new Zend_Db_Profiler_Firebug('All DB Queries'); $profiler->setEnabled(true); $this->getPluginResource('db')->getDbAdapter()->setProfiler($profiler); } } /** * Add Controller Action Helpers */ protected function _initActionHelpers() { $this->_logger->info('Bootstrap ' . __METHOD__); Zend_Controller_Action_HelperBroker::addHelper(new SF_Controller_Helper_Acl()); Zend_Controller_Action_HelperBroker::addHelper(new SF_Controller_Helper_RedirectCommon()); Zend_Controller_Action_HelperBroker::addHelper(new SF_Controller_Helper_Service()); } /** * * @return unknown_type */ protected function _initRoutes(){ $this->_logger->info('Initialize Routes '. __METHOD__); $this->bootstrap('frontController'); $router = $this->frontController->getRouter(); $route = new Zend_Controller_Router_route( 'register', array( 'controller' => 'user', 'action' => 'register' ) ); $router->addRoute('register',$route); $route = new Zend_Controller_Router_route( 'login', array( 'controller' => 'user', 'action' => 'login' ) ); $router->addRoute('login',$route); $route = new Zend_Controller_Router_route( 'logout', array( 'controller' => 'user', 'action' => 'logout' ) ); $router->addRoute('logout',$route); } /** * * @return void */ protected function _initLocale(){ $this->_logger->info('Bootstrap '.__METHOD__); $locale = new Zend_Locale('nl_NL'); Zend_Registry::set('Zend_Locale', $locale); } protected function _initAcl(){ $this->_acl = new EventManager_Service_Acl(); } /** * * @return void */ protected function _initViewSettings(){ $this->_logger->info('Bootstrap '.__METHOD__); $this->bootstrap('view'); $this->bootstrap('Acl'); $this->_view = $this->getResource('view'); //set encoding and doctype $this->_view->setEncoding('UTF-8'); $this->_view->doctype('XHTML1_STRICT'); $this->_view->headMeta()->appendHttpEquiv('Content-Type', 'text/html; charset=UTF-8'); $this->_view->headMeta()->appendHttpEquiv('Content-Language', 'en-US'); //@todo op een later moment moeten hier nog de stylesheets worden toegevoegd $this->_view->headLink()->appendStylesheet('/css/main.css'); //$this->_view->headTitle('Event Manager'); /* Set the head style. $this->_view->headTitle->headStyle(); */ $this->_view->headTitle()->setSeparator(' - '); $this->_auth = Zend_Auth::getInstance(); $navigation = new Zend_Config_Xml(APPLICATION_PATH.'/configs/navigation.xml','nav'); $navContainer = new Zend_Navigation($navigation); $this->_view->navigation($navContainer)->setAcl($this->_acl)->setRole($this->_auth->getStorage()->read()->usr_role); //THIS IS LINE 169!!!!!!!!! } /** * Add graceful error handling to the dispatch, this will handle * errors during Front Controller dispatch. */ public function run() { $errorHandling = $this->getOption('errorhandling'); try { parent::run(); } catch(Exception $e) { if (true == (bool) $errorHandling['graceful']) { $this->__handleErrors($e, $errorHandling['email']); } else { throw $e; } } } /** * Handle errors gracefully, this will work as long as the views, * and the Zend classes are available * * @param Exception $e * @param string $email */ protected function __handleErrors(Exception $e, $email) { header('HTTP/1.1 500 Internal Server Error'); $view = new Zend_View(); $view->addScriptPath(dirname(__FILE__) . '/../views/scripts'); echo $view->render('fatalError.phtml'); if ('' != $email) { $mail = new Zend_Mail(); $mail->setSubject('Fatal error in application Storefront'); $mail->addTo($email); $mail->setBodyText( $e->getFile() . "\n" . $e->getMessage() . "\n" . $e->getTraceAsString() . "\n" ); @$mail->send(); } } } I have tried to debug my code, but everyting goes well until I do somethign with the db. But I don't know what goes wrong with the db. I don't get any clear error messages. Can someone help me? Some more possible interesting data: [bootstrap] resources.db.adapter = "PDO_MYSQL" resources.db.isdefaulttableadapter = true resources.db.params.dbname = "ladosa" resources.db.params.username = "root" resources.db.params.password = "root" resources.db.params.hostname = "localhost" resources.db.params.charset = "UTF8" resources.db.params.profiler.enabled = true resources.db.params.profiler.class = Zend_Db_Profiler_Firebug Autoloadernamespaces[] = "Zend_" Autoloadernamespaces[] = "SF_" phpsettings.display_errors = 0 phpsettings.error_reporting = 8191 phpSettings.date.timezone = "Europe/Amsterdam" bootstrap.path = APPLICATION_PATH"/bootstrap/Bootstrap.php" pluginPaths.resource_ = APPLICATION_PATH"/resources" resources.frontcontroller.moduledirectory = APPLICATION_PATH"/modules" resources.frontcontroller.defaultmodule = "eventManager" resources.frontcontroller.params.prefixDefaultModule = true resources.frontcontroller.exceptions = false resources.view[] = "" resources.layout.layoutPath = APPLICATION_PATH "/layouts/scripts" resources.view.encoding = "UTF-8" resources.view.title = Rode kruis Vrijwilligers applicatie ;resources.view.helperPath.Default_View_Helper = APPLICATION_PATH "/modules/eventManager/views/helpers" resources.layout.layout = "main" [production:bootstrap] [development:bootstrap] ;resources.frontController.throwExceptions = 1 ;phpSettings.display_startup_errors=1 ;phpSettings.display_errors = 1 ;resources.frontcontroller.throwerrors = [test:production] btw. I CAN login to my database command line with the given username and password. Update: today i decided to investigate on my http request and i came to an error 500. My apache logs don't give any related information, I think. I posted the logs above. Any idea's?

    Read the article

  • SSO "Portal"

    - by Clinton Blackmore
    Pursuant to my question on alleviating the password explosion, I've contacted some of the services to whom we are paying money to access their websites to ask if we could authenticate our own users, and some of them said yes and send me specs on how to do so. (One of the sites called such a system a page a "portal"; I've never heard the term used in quite that way.) It is simple enough that I am tempted to roll my own. The largest complication is that one site wants us to store a key for every user in our database (and I think the LDAP database makes sense) after their initial login. So, non-trivial, but doable. The nature of these sorts of tasks, I expect, is that if they start out small and simple, they don't end that way. There must be some software that addresses this that is readily extended, surely. In my searching, I've come across: SimpleSAMLphp JOSSO RubyCAS-Server Shibboleth Pubcookie OpenID [Wow, gee. I'd missed some of those in my previous searches! The wikipedia page on Central Authentication Services is useful, and the section on Alternatives to OpenID makes it look like there is a lot of choice.] Can anyone recommend any of these, or suggest ones to avoid? Internally, we are authenticating using Apple's Open Directory [ == OpenLDAP + Kerberos + Password Server (which, I believe, == SAML) ]. As far as extending/tweaking/advanced configuration of a system, I am able to program in Python, C++, can do some basic PHP, and may be able to remember some Java. Looks like I need to pick up Ruby at some point. Addendum: I would also like users to be able to change their passwords over the web (and for certain users to change passwords of other users).

    Read the article

  • Windows 8.1 - Won't boot (0xc000000f), bcdedit fails

    - by user3014097
    I’m pretty much stuck at this point. So, backstory: Windows was installed on one of the SSDs currently in my tower. I bought a new SSD to install Windows (8.1 64 bit) on. Windows installation went fine, booted up, and formatted the old SSD from within Windows (this seems to have been a mistake, but I didn’t realize that at the time). Despite formatting the old SSD, whenever I tried to boot I was told that there were 2 Windows installations. Apparently, when I formatted the old drive, not all of the partitions were removed. So, I booted up with the repair utility, went into cmd, and deleted the non-primary partitions on the old SSD (there were 2 – think they were system and recovery, although I’m forgetting now). Reboot – computer won’t boot. Getting the 0xc000000f “The boot selection failed because a required device is inaccessible” error. Troubleshooting so far: Automatic repair doesn’t fix anything (I’ve never had luck with it though) If I go to install a new version of Windows, the drives and partitions are all there. The SSD is functioning, I at least know that. I’ve essentially gone through this guide: https://neosmart.net/wiki/recovering-windows-bootloader/ Unfortunately, I’m not getting anywhere. I’m not even entirely sure how to describe the errors I’m getting, so I’ve just included pictures of every step (I can't actually post them though so I just included a photobucket link). http://s319.photobucket.com/user/DGalt11/library/Computer%20Issue Am I completely screwed here (i.e. reformat and reinstall?)? Thanks

    Read the article

  • Shared files folder in Amazon Elastic Beanstalk environment

    - by por
    I'm working on a Drupal application, which is planned to be hosted in Amazon Elastic Beanstalk environment. Basically, Elastic Beanstalk enables the application to scale automatically by starting additional web server instances based on predefined rules. The shared database is running on an Amazon RDS instance, which all instances can access properly. The problem is the shared files folder (sites/default/files). We're using git as SCM, and with it we're able to deploy new versions by executing $ git aws.push. In the background Elastic Beanstalk automatically deletes ($ rm -rf) the current codebase from all servers running in the environment, and deploys the new version. The plan was to use S3 (s3fs) for shared files in the staging environment, and NFS in the production environment. We've managed to set up the environment to the extent where the shared files folder is mounted after a reboot properly. But... The Problem is that, in this setup, the deployment of new versions on running instances fail because $ rm -rf can't remove the mounted directory, and as result, the entire environment goes down and we need restart the environment, which isn't really an elegant solution. Question #1 is that what would be the proper way to manage shared files in this kind of deployment? Are you running such an environment? How did you solve the problem? By looking at Elastic Beanstalk Hostmanager code (Ruby) there seems be a way to hook our functionality (unmount if mounted in pre-deploy and mount in post-deploy) into Hostmanager (/opt/hostmanager/srv/lib/elasticbeanstalk/hostmanager/applications/phpapplication.rb) but the scripts defined in the file (i.e. /tmp/php_post_deploy_app.sh) don't seem to be working. That might be because our Ruby skills are non-existent. Question #2 is that did you manage to hook your functionality in Hostmanager in a portable way (i.e. by not changing the core Hostmanager files)?

    Read the article

  • CDROM does not appear on desktop, MACOS 10.5.7

    - by Cheeso
    When I pop a CDROM into the drive of my Macbook Pro, It spins up, I hear it, but no icon appears on the desktop. (I think it's 10.5.7; actually not sure how to verify this on Mac, but I think I saw a 10.5.7 flash by somewhere). In the finder preferences, I have "Show these items on the Desktop" set to show HDs, External Disks, and CDs, DVDs, and ipods. All three of those are checked. I do see the internal HD on the desktop. In Disk utility I can see the CD/DVD hardware. It says "MATSHITA DVD-R UJ-857E...". From Disk Utility I can eject the drive. But in Finder, there is never a CD/DVD listed under "Devices". When I insert a disk, nothing happens, I cannot see it. I also cannot boot from bootable CDROMs by holding C down . Suggestions? I am not very experienced with Mac; I have used Windows for years. EDIT Two updates: I saw this article on support.apple.com, and modified the hostconfig appropriately. It did not have the AUTODISKMOUNT entry, so I added one, rebooted. Same behavior. It does not see the CDROM in Finder, does not mount it on desktop. I put an old manufactured CDROM into the drive, and voila! it showed up on the desktop. The CD that does not appear is a GNome Partition Editor Live CD, which I guess is based on debian. That CD boots in other (non-Mac) PCs. I want to use this to adjust the Bootcamp partition. Suggestions?

    Read the article

  • How to move the Windows 7 bootloader to the Windows 7 partition?

    - by pauldoo
    I recently installed Windows 7 in a triple boot setup alongside XP and Linux. When I was finished and was in the process of restoring the bootloader for Linux I discovered something strange about what Windows 7 had done. I discovered that Windows 7 had not installed a bootloader to it's own partition, and instead had instead set up a bootloader on the pre-existing XP partition that offers a choice between 7 and XP. This behaviour has been noticed by others. Now my booting is slightly odd. I have GRUB on the MBR which lets me choose between Linux and Windows. When I select Windows I have Grub boot to the XP partition where I get the 2nd choice between 7 and XP. Why doesn't the Windows 7 installer put the Windows 7 bootloader on the Windows 7 partition like all previous MS OSs? This is now going to be a real problem for me, as I now want to wipe the XP partition and install something else there (probably another non-MS OS). How can I move the bootloader for Windows 7 onto the Windows 7 partition, thus making it bootable and allowing me to safely wipe the XP partition?

    Read the article

  • Saving a file in a CSV type in Excel always removes the BOM

    - by rickp
    I've been trying to find a reasonable solution/explanation (unsuccessfully) to find out why Excel defaults to removing the BOM when saving a file to the CSV type. Please forgive me if you find this a duplicate of this question. This handles reading CSV files with non-ASCII encoding, but it doesn't cover saving the file back out (which is where the biggest issue lies). Here is my current situation (which I'm going to gather is common among localized software dealing with Unicode characters and a CSV format): We export data to a CSV format using UTF-16LE, ensuring the BOM is set (0xFFFE). We validate after the file is generated with a Hex editor to ensure it was set correctly. Open the file in Excel (for this example we're exporting Japanese characters) and witness that Excel handles loading the file with the correct encoding. Attempts to save this file will prompt you with a warning message indicating that the file may contain features that may not be compatible with Unicode encoding, but asks if you'd like to save anyway. If you select the Save As dialog, it will immediately ask you to save the file as "Unicode Text" rather than CSV. If you select the "CSV" extension and save the file it removes the BOM (obviously along with all the Japanese characters). Why would this happen? Is there a solution to this problem, or is this a known 'bug'/limitation of Excel? Additionally (as a side issue) it appears that Excel, when loading UTF-16LE encoded CSV files, only uses TAB delimiters. Again, is this another known 'bug'/limitation of Excel?

    Read the article

  • Cyrus: In practical terms, how do end users administer their shared mailboxes?

    - by Nick
    Let's say we have four customer service reps: Billy, Bob, Joe, and Tom. Tom is the department manager. There's a shared Customer Service mailbox on the Cyrus server that they all have access to. Tom, as the manager also has administrative privileges for the shared mailbox. They decide they want to create sub-folders a certain way, and Tom creates them. They're all running Thunderbird, so Tom right-clicks the main folder and chooses "New Subfolder". Now Tom has the Subfolders he needs and the other sales reps have... nothing! Because Cyrus created the Subfolders giving Tom "Full Access" permissions, and everyone else gets no access. So how does Tom give the other reps in his department access to the new folders? As far as Cyrus is concerned, Tom has permission to grant others access to his new mailboxes- But as far as I can tell, there's no option in Thunderbird for granting mailbox permissions. An IT staff member should not have to receive a support request every time someone wants to add a Subfolder to a shared mailbox. That's why we make certain users into mailbox admins in the first place! But asking (non-technical) users to SSH into an IMAP server to run cyradm seems like a bad idea too. Certainly someone has found a solution for this dilemma. Perhaps a Thunderbird extension for setting Cyrus permissions? Or something like umask that forces subfolders to have identical permissions to their parents on creation? And related, what about Sieve configuration? Is there anyway that can be done from the client machine too? Thanks, Nick

    Read the article

  • Authenticate VNC session with ConsolKit?

    - by lori
    I have a linux machine running Fedora 16 in a cupboard. It has no screen or keyboard. I connect to it using a combination of vnc and ssh. Recently, after an update, I have had issues with authentication on the machine. If I vnc to it, the kde desktop pops up an error dialog every few minutes saying Authorization failed. Failed to obtain authentication. If I plug in a USB drive it fails to mount, Dolphin reports an authentication issue again. I have had limited success finding the solution. AFAICT, it is an issue with ConsoleKit deeming me to be a non-local user so it prevents authentication. This is the output from ck-list-sessions: $ ck-list-sessions Session5: unix-user = '1000' realname = 'steve' seat = 'Seat6' session-type = '' active = FALSE x11-display = ':1' x11-display-device = '' display-device = '' remote-host-name = '' is-local = FALSE on-since = '2012-09-16T08:07:03.137011Z' login-session-id = '1' I have tried to update my .vnc/xstartup script to include ck-launch-session as follows: $ cat ~/.vnc/xstartup #!/bin/sh exec ck-launch-session vncconfig -iconic & unset SESSION_MANAGER unset DBUS_SESSION_BUS_ADDRESS export XKL_XMODMAP_DISABLE=1 OS=`uname -s` if [ $OS = 'Linux' ]; then case "$WINDOWMANAGER" in *gnome*) if [ -e /etc/SuSE-release ]; then PATH=$PATH:/opt/gnome/bin export PATH fi ;; esac fi if [ -x /etc/X11/xinit/xinitrc ]; then exec ck-launch-session /etc/X11/xinit/xinitrc fi if [ -f /etc/X11/xinit/xinitrc ]; then exec ck-launch-session sh /etc/X11/xinit/xinitrc fi [ -r $HOME/.Xresources ] && xrdb $HOME/.Xresources exec ck-launch-session xsetroot -solid grey exec ck-launch-session xterm -geometry 80x24+10+10 -ls -title "$VNCDESKTOP Desktop" & exec ck-launch-session twm & This has not helped. How can I either authenticate myself to ConsoleKit, or trick it into believing I am a local user?

    Read the article

  • Which Linux distributions work on IBM's JS20 PowerPC blade?

    - by Matthew Rankin
    Which Linux distributions have people successfully gotten working on an IBM JS20 Blade, which has the PowerPC 970 processor? Specifically, I'm interested in distributions other than RHEL and SLES. What gotchas need to be watched out for when installing a particular distribution of Linux on the JS20? Non-Specific Distribution Information IBM's Linux on BladeCenter JS20 IBM's eServer BladeCenter JS20 Whitepaper — "The JS20 blade supports all popular Linux distributions including Red Hat®, Inc., and SUSE LINUX." PenguinPPC Distributions List PPCLinux — "This project is a repository of information on how to run GNU/Linux on PowerPC architectures." Ubuntu Specific Information Ubuntu PowerPC FAQ — "Ubuntu 6.10 was the last officially supported PowerPC version of Ubuntu." Ubuntu PowerPC Download Ubuntu 8.04 PowerPC Supported Hardware Ubuntu 9.10 Ports — Mac (PowerPC) and IBM-PPC (POWER5) server install CD. For Apple Macintosh G3, G4, and G5 computers, including iBooks and PowerBooks as well as IBM OpenPower machines. Debian Specific Information Debian on PowerPC —"We may have a 64bit port in the future." Looks like there is only a 32-bit version available currently. Debian on JS20 blades Installing Debian Etch on IBM JS20s Gentoo Specific Information Gentoo Linux Crux PPC Specific Information Crux PPC

    Read the article

  • Windows Server NTFS volume list file name encodings and any illegal file names

    - by benbradley
    I'm having to deal with a Windows Server (NTFS) file server and our backup application appears to be failing with certain files. According to this https://en.wikipedia.org/wiki/NTFS#Internals NTFS apparently supports file names encoded in UTF-16 but according to their support team, our backup application only supports UTF-8. I'd like to confirm whether this is actually the problem by seeing the file name encoding for myself. The files that are failing appear to be using plain English A-Z letters and other ASCII characters. No accents or non-English letters etc. I suppose even though the letters appear to be plain A-Z the file name could still be encoded in UTF-16. Does anyone know of a utility or script that can recursively go through all files in a directory and show the encoding of the file name? Then I could try renaming to UTF-8 to see if the backup can proceed. I'm not a Windows developer so can't write this up myself. Presumably the encoding of the file name should be stored in the FS somewhere and therefore it should be possible to expose this.

    Read the article

  • Hardware doesn't work some times

    - by Ali
    I have an Asus n51vf laptop. I bought it not long time ago (less than a month) and installed Windows 7 on it. Since that it wasn't new when I bought it, I don't know, if the problem was occuring before re-installing Windows 7. There are two problems, that might (or might not) have something to do with each other: Problem The less annoying problem is that the screen flickers ONLY on YouTube when scrolling and/or pausing/playing the video or moving the curser over the video. The second more timeconsuming problem is that some of the hardware doesn't work when I turn up the computer. Then I have to reboot the computer and try again. Example: I turn on the computer, and the touchpad doesn't work - I then reboot and it works again. This has so far happened to the screen (leading to a black screen), the keyboard and the touchpad. More frequently the mouse. What have I tried to do so far? I tried reeinstalling the touchpad driver (Synaptic Touchpad driver from Asus Support Page) - didn't help at all. I even tried reinstalling the driver when the non-responding mouse on startup-problem occured (using the keyboard), but it asked me to reboot and didn't help at all. I also installed (and reinstalled) the graphics driver; it's a GeForce GT 130M. Now, the problem never occurs spontaneously - it only appears when booting my computer. I can even use the computer for heavy tasks (games, multiple programs running etc.) with no problem at all. I suspect, that the problem is in some booting mechanism that fails: Maybe the Windows driver loading? Motherboard problems?

    Read the article

  • Ubuntu 12.04 - HP ProLiant DL380 G4 - Load Maxes Out / Unresponsive

    - by Brian S
    Trying to post this question on here. I've posted it on the Ubuntu forums as well with no replies. Recently I upgraded an HP ProLiant DL380 G4 server from Ubuntu 10.04 server to Ubuntu 12.04 server. Upon doing so, the server will not - at random times - get to a load of 400+ and then become completely non-responsive. I use an SNMP graphing program (cacti) and the load steadily increases by about 10 every five minutes until it gets over 400 and the graphing stops. The graphs may not be accurate, but the CPU load averages about 3% before this happens - and right when the load starts increasing, it jumps to about 25% for 15 minutes and dramatically dips down to less than 1% (about 0.3%) until the graphing stops. I'm not able to open a SSH tunnel to the server to do anything. I've checked the /var/log/syslog and all logging stops at that time as well - with nothing else in there. The odd thing is - the server still responds to DNS queries for the zones it is authoritative on during this time - and at normal speed. Just not sure what the next step would be in order to find out what is going on - and how this issue can be corrected. The server cannot stay with Ubuntu 10.04 Server and needs to stay upgraded.

    Read the article

  • Bypass proxy authentication [closed]

    - by Diego Queiroz
    My scenario: My network has a proxy that requires interative authentication. When I access any URL, an username and password is requested to enable navigation. I do have a valid username/password (this means I have permissions to access external content). I do not have access to the proxy server (any change to the proxy server is not an option). What I need: I need to bypass the interative authentication process and make it an automated authentication process. What I do NOT need/want: I do not need/want to hack the network. I do not need/want to access unauthorized content. In other words, I just need to find a way to "save" my password in the computer (security is not a problem) to allow application that does not support this kind of interative authentication to access the internet (like non-browser software that also uses HTTP port). My guess: My guess is to develop a new proxy server that will run in the local machine (eg, a proxy for the network proxy). This proxy server will access my network proxy, authenticate and forward the content. Of course this is a last resort. I prefer to not need to develop a proxy server. Does someone know other solution? (any operating system)

    Read the article

  • Administrator view all mapped drives

    - by kskid19
    In my understanding of security, an administrator should be able to view all connections to and from a computer - just as they can view all processes/owner, network connections/owning process. However, Windows 8 seems to have disabled this. As administrator running an elevated in Win Vista+ when you run net use you get back all drives mapped, listed as unavailable. In Windows 8, the same command run from an elevated prompt returns "There are no entries in the list". The behavior is identical for powershell Get-WmiObject Win32_LogonSessionMappedDisk. A workaround for persistent mappings is to run Get-ChildItem Registry::HKU*\Network*. This does not include temporary mappings (in my particular example it was created through explorer on an administrator account and I did not select "Reconnect at sign-in") Is there a direct/simple way for Administrator to view connections of any user (short of a script that runs under each user context)? I have read Some Programs Cannot Access Network Locations When UAC Is Enabled but I do not think it particularly applies. ServerFault has an answer, but it still does not address non-persistent drives How can I tell what network drives users have mapped?

    Read the article

  • Administrator view ALL mapped drives

    - by kskid19
    In my understanding of security, an administrator should be able to view all connections to and from a computer - just as they can view all processes/owner, network connections/owning process. However, Windows 8 seems to have disabled this. As administrator running an elevated in Win Vista+ when you run net use you get back all drives mapped, listed as unavailable. In Windows 8, the same command run from an elevated prompt returns "There are no entries in the list". The behavior is identical for powershell Get-WmiObject Win32_LogonSessionMappedDisk. A workaround for persistent mappings is to run Get-ChildItem Registry::HKU*\Network*. This does not include temporary mappings (in my particular example it was created through explorer on an administrator account and I did not select "Reconnect at sign-in") Is there a direct/simple way for Administrator to view connections of any user (short of a script that runs under each user context)? I have read Some Programs Cannot Access Network Locations When UAC Is Enabled but I do not think it particularly applies. I have seen this answer, but it still does not address non-persistent drives How can I tell what network drives users have mapped?

    Read the article

  • preformance wise htaccess

    - by purpler
    hese's the my htaccess template, i wonder if anything could be added to increase website performance.. # Defaults AddDefaultCharset UTF-8 DefaultLanguage en-US ServerSignature Off FileETag None Header unset ETag Options -MultiViews #Options All -Indexes # Force the latest IE version or ChromeFrame <IfModule mod_setenvif.c> <IfModule mod_headers.c> BrowserMatch MSIE ie Header set X-UA-Compatible "IE=Edge,chrome=1" env=ie </IfModule> </IfModule> # Proxy X-UA Setup <IfModule mod_headers.c> Header append Vary User-Agent </IfModule> #Rewrites Options +FollowSymlinks RewriteEngine On RewriteBase / # Redirect to non-WWW RewriteCond %{HTTPS} !=on RewriteCond %{HTTP_HOST} ^www\.(.+)$ [NC] RewriteRule ^(.*)$ http://%1/$1 [R=301,L] # Redirect to WWW RewriteCond %{HTTP_HOST} ^domain.com RewriteRule (.*) http://www.domain.com/$1 [R=301,L] # Redirect index to root RewriteRule ^(.*)index\.(php|html)$ /$1 [R=301,L] # Caching ExpiresActive On ExpiresDefault A0 Header set Cache-Control "public" # 1 Year Long Cache <FilesMatch "\.(flv|fla|ico|pdf|avi|mov|ppt|doc|mp3|wmv|wav|png|jpg|jpeg|gif|swf|js|css|ttf|eot|woff|svg|svgz)$"> ExpiresDefault A31622400 </FilesMatch> # Proxy Caching <FilesMatch "\.(css|js|png)$"> ExpiresDefault A31622400 Header set Cache-Control "private" </FilesMatch> # Protect against DOS attacks by limiting file upload size LimitRequestBody 10240000 # Proper SVG serving AddType image/svg+xml svg svgz AddEncoding gzip svgz # GZip Compression <IfModule mod_deflate.c> <FilesMatch "\.(php|html|css|js|xml|txt|ttf|otf|eot|svg)$" > SetOutputFilter DEFLATE </FilesMatch> </IfModule> # Error page ErrorDocument 404 /404.html # Deny access to sensitive files <FilesMatch "\.(htaccess|ini|log|psd)$"> Order Allow,Deny Deny from all </FilesMatch>

    Read the article

  • Should I upgrade to Symantec Endpoint Protection?

    - by Alex C.
    I'm the IT manager at an animal shelter in Upstate New York. We have a Windows network with about 50 desktops running Windows XP Pro. We used to use CA eTrust Antivirus, but that product didn't work too well (too many infections got through). About six months ago, we switched to using Symantec Antivirus Corporate Edition ver. 10.1.8.8000. If anything, the Symantec product is even worse. The last six weeks in particular have been very bad -- we've had about seven or eight PCs get hit with those malware infections that masquerade as antivirus software. In most of those cases, Symantec didn't even flag the malware at all. So... what gives with the Symantec Antivirus? As far as I can tell, it's installed correctly and downloading updated definitions nightly. I can upgrade to Symantec Endpoint Protection for $220 (we get non-profit pricing), but I don't want to do it if it's not going to be significantly better. Any advice? Should I switch to something else entirely? Thanks!

    Read the article

  • ipmi - can't ping or remotely connect

    - by Fidel
    I've tried configuring the IPMI controller to accept remote connections, but I can't even ping it. Here is it status: #/usr/local/bin/ipmitool lan print 2 Set in Progress : Set Complete Auth Type Support : NONE PASSWORD Auth Type Enable : Callback : : User : NONE PASSWORD : Operator : PASSWORD : Admin : PASSWORD : OEM : IP Address Source : Static Address IP Address : 192.168.1.112 Subnet Mask : 255.255.255.0 MAC Address : 00:a0:a5:67:45:25 IP Header : TTL=0x40 Flags=0x40 Precedence=0x00 TOS=0x10 BMC ARP Control : ARP Responses Enabled, Gratuitous ARP Enabled Gratituous ARP Intrvl : 8.0 seconds Default Gateway IP : 192.168.1.1 Default Gateway MAC : 00:00:00:00:00:00 802.1q VLAN ID : Disabled 802.1q VLAN Priority : 0 RMCP+ Cipher Suites : 0,1,2,3 Cipher Suite Priv Max : uaaaXXXXXXXXXXX : X=Cipher Suite Unused : c=CALLBACK : u=USER : o=OPERATOR : a=ADMIN : O=OEM # /usr/local/bin/ipmitool user list 2 ID Name Enabled Callin Link Auth IPMI Msg Channel Priv Limit 1 true false true true USER 2 admin true false true true ADMINISTRATOR # /usr/local/bin/ipmitool channel getaccess 2 2 Maximum User IDs : 5 Enabled User IDs : 2 User ID : 2 User Name : admin Fixed Name : No Access Available : callback Link Authentication : enabled IPMI Messaging : enabled Privilege Level : ADMINISTRATOR # /usr/local/bin/ipmitool channel info 2 Channel 0x2 info: Channel Medium Type : 802.3 LAN Channel Protocol Type : IPMB-1.0 Session Support : multi-session Active Session Count : 0 Protocol Vendor ID : 7154 Volatile(active) Settings Alerting : disabled Per-message Auth : disabled User Level Auth : disabled Access Mode : always available Non-Volatile Settings Alerting : disabled Per-message Auth : disabled User Level Auth : disabled Access Mode : always available # /usr/local/bin/ipmitool chassis status System Power : on Power Overload : false Power Interlock : inactive Main Power Fault : false Power Control Fault : false Power Restore Policy : unknown Last Power Event : Chassis Intrusion : inactive Front-Panel Lockout : inactive Drive Fault : false Cooling/Fan Fault : false # arp Address HWtype HWaddress Flags Mask Iface 192.168.1.112 ether 00:A0:A5:67:45:25 C bond0 # /usr/local/bin/ipmitool -I lan -H 192.168.1.112 -U admin -P admin chassis power status Error: Unable to establish LAN session Unable to get Chassis Power Status In summary. It exists on the ARP list so arp's are being broadcast. I can't ping it and can't connect to it. Can anyone spot any glaring mistakes in the configuration? Many thanks, Fidel

    Read the article

  • Keyboard's media keys are blocked by a program

    - by Mike Hanson
    I've got a Microsoft Natural Ergonomic Keyboard 4000. In addition to the regular keys, it's also got keys for Web/Home, Search, Mail, Favorites (5), Calculator, and Media functions (Mute, Volume Up/Down, and Play/Pause). Everything works most of the time, and the exception is rather odd. I use a programming system called Clarion. When that has focus, the Media keys don't work. (All the others still do.) I've also discovered that programs that I create using Clarion also block the media keys (only when they have focus). This indicates that it's probably something in Clarion's Run-Time Library (RTL) that's causing the trouble. The keys will work if I click on a non-Clarion window before hitting the media key, but that's an undesirable hassle. The odd thing is that I have many colleagues with the same keyboard, and they have no problem. When I recently upgraded from Vista Professional to Win7 Ultimate, I noticed that various things "appear" differently. For example, with my old system, when I changed the volume or muted the volume bar visualization always appeared at the bottom right on the screen. Now it doesn't appear in certain programs, even when it works. This indicates an order of precedence for visual elements. I'm fairly certain a similar order of precedence exists for keyboard hooks. Depending on how the hooks are defined, and the order in which they're applied, it would seem that sometimes the IntelliType drivers don't see the media keystrokes. The Media keys probably behave differently than the rest of the "special" keys, because they are more of a standard across all keyboards, so perhaps are handled by a different driver hooking mechanism. Does anyone have any suggestions of how I might fix this problem? Is there some way to change the order of hooks? Delay the loading of the IntelliType driver? Thanks in advance!

    Read the article

< Previous Page | 392 393 394 395 396 397 398 399 400 401 402 403  | Next Page >