Search Results

Search found 249 results on 10 pages for 'asa baylus'.

Page 4/10 | < Previous Page | 1 2 3 4 5 6 7 8 9 10  | Next Page >

  • QoS basics on a Cisco ASA

    - by qbn
    Could someone briefly explain how to use QoS on Cisco ASA 5505? I have the basics of policing down, but what about shaping and priorities? Basically what I'm trying to do is carve out some bandwidth for my VPN subnets (in an object-group called priority-traffic). I've seen this Cisco QoS document, however configuring shaping and priority-queue don't seem to have any effects in my test. A full download of the linux kernel from kernel.org will boost a ping to a server via VPN sky high. Policing has been successful in passing this test, although it doesn't seem as efficient (I cap non-vpn traffic at 3 of my 4.5 megabits of bandwidth). Am I misunderstanding the results of the test? I think there is some simple concept I'm not grasping here. EDIT: Here is my config thus far (I have 4.5 megabits of bandwidth): access-list priority-traffic extended permit ip object-group priority-traffic any access-list priority-traffic extended permit ip any object-group priority-traffic access-list priority-traffic extended permit icmp object-group priority-traffic any access-list priority-traffic extended permit icmp any object-group priority-traffic access-list non-priority-traffic extended deny ip object-group priority-traffic any access-list non-priority-traffic extended deny ip any object-group priority-traffic access-list non-priority-traffic extended permit ip any any priority-queue outside queue-limit 440 class-map non-priority-traffic match access-list non-priority-traffic class-map priority-traffic match access-list priority-traffic class-map inspection_default match default-inspection-traffic policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp policy-map outbound-qos-policy class non-priority-traffic police input 2500000 police output 2500000 class priority-traffic priority service-policy global_policy global service-policy outbound-qos-policy interface outside

    Read the article

  • Unable to install PEM/pkcs12 created by gnutls to Cisco ASA

    - by ACiD GRiM
    I've been pulling some hair out trying to figure out why cisco devices don't like my certificates. My primary need is to get a trustpoint set up with CA,cert,key on the ASA for VPN systems, however I'm having the same issues on my IOS devices. I created a pkcs12 with openssl a few months ago that imported with no issues, but now that I'm getting ready to move this lab to production I'm using gnutls certtool as I found it adds alt_dns and ip_address fields properly to the certificate, (which cost me a few more hairs trying to get to work with openssl's ca tool) I'm including the current test certs below, don't worry I'm not using these in production ;) The maddening thing is that after I thought gnutls was generating certs incorrectly, I tried making a pkcs12 for a printserver and it imported with no issues. Here's my command flow for creating these certs: certtool --generate-privkey --disable-quick-random --outfile nn-ca.key certtool --generate-self-signed --load-privkey nn-ca.key --outfile nn-ca.crt certtool --generate-privkey --disable-quick-random --outfile nn-g0.key certtool --generate-certificate --load-privkey nn-g0.key --outfile nn-g0.crt --load-ca-privkey nn-ca.key --load-ca-certificate nn-ca.crt openssl pkcs12 -export -certfile nn-ca.crt -in nn-g0.crt -inkey nn-g0.key -out nn-g0.p12 openssl enc -base64 -in nn-g0.p12 -out nn-g0.base64.p12 The password for the attatched pkcs12 is "ciscohelp" without quotes. Thanks for any help TestCerts

    Read the article

  • Problems with ipsec betwen Cisco ASA 5505 and Juniper ssg5

    - by Oskar Kjellin
    I am trying to set up an ipsec tunnel between our ASA 5505 and a Juniper ssg5. The tunnel is up and running, but I cannot get any data through it. The local network I am on is 172.16.1.0 and the remote is 192.168.70.0. But I cannot ping anything on their netowork. I receive a "Phase 2 OK" when I set up the ipsec. I think this is the part of the config that is applicable. It seems like the data is not routed through the tunnel, but I am not sure... object network our-network subnet 172.16.1.0 255.255.255.0 object network their-network subnet 192.168.70.0 255.255.255.0 access-list outside_cryptomap extended permit ip object our-network object their-network crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto map outside_map 1 match address outside_cryptomap crypto map outside_map 1 set pfs crypto map outside_map 1 set peer THEIR_IP crypto map outside_map 1 set ikev1 phase1-mode aggressive crypto map outside_map 1 set ikev1 transform-set ESP-3DES-MD5 crypto map outside_map 1 set ikev2 pre-shared-key ***** crypto map outside_map 1 set reverse-route crypto map outside_map interface outside webvpn group-policy GroupPolicy_THEIR_IP internal group-policy GroupPolicy_THEIR_IP attributes vpn-filter value outside_cryptomap ipv6-vpn-filter none vpn-tunnel-protocol ikev1 tunnel-group THEIR_IP type ipsec-l2l tunnel-group THEIR_IP general-attributes default-group-policy GroupPolicy_THEIR_IP tunnel-group THEIR_IP ipsec-attributes ikev1 pre-shared-key ***** ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key *****

    Read the article

  • Trouble setting up incoming VPN in Microsoft SBS 2008 through a Cisco ASA 5505 appliance

    - by Nils
    I have replaced an aging firewall (custom setup using Linux) with a Cisco ASA 5505 appliance for our network. It's a very simple setup with around 10 workstations and a single Small Business Server 2008. Setting up incoming ports for SMTP, HTTPS, remote desktop etc. to the SBS went fine - they are working like they should. However, I have not succeeded in allowing incoming VPN connections. The clients trying to connect (running Windows 7) are stuck with the "Verifying username and password..." dialog before getting an error message 30 seconds later. We have a single external, static IP, so I cannot set up the VPN connection on another IP address. I have forwarded TCP port 1723 the same way as I did for SMTP and the others, by adding a static NAT route translating traffic from the SBS server on port 1723 to the outside interface. In addition, I set up an access rule allowing all GRE packets (src any, dst any). I have figured that I must somehow forward incoming GRE packets to the SBS server, but this is where I am stuck. I am using ADSM to configure the 5505 (not console). Any help is very much appreciated!

    Read the article

  • ASA access lists and Egress Filtering

    - by Nate
    Hello. I'm trying to learn how to use a cisco ASA firewall, and I don't really know what I'm doing. I'm trying to set up some egress filtering, with the goal of allowing only the minimal amount of traffic out of the network, even if it originated from within the inside interface. In other words, I'm trying to set up dmz_in and inside_in ACLs as if the inside interface is not too trustworthy. I haven't fully grasped all the concepts yet, so I have a few issues. Assume that we're working with three interfaces: inside, outside, and DMZ. Let's say I have a server (X.Y.Z.1) that has to respond to PING, HTTP, SSH, FTP, MySQL, and SMTP. My ACL looks something like this: access-list outside_in extended permit icmp any host X.Y.Z.1 echo-reply access-list outside_in extended permit tcp any host X.Y.Z.1 eq www access-list outside_in extended permit tcp any host X.Y.Z.1 eq ssh access-list outside_in extended permit tcp any host X.Y.Z.1 eq ftp access-list outside_in extended permit tcp any host X.Y.Z.1 eq ftp-data established access-list outside_in extended permit tcp any host X.Y.Z.1 eq 3306 access-list outside_in extended permit tcp any host X.Y.Z.1 eq smtp and I apply it like this: access-group outside_in in interface outside My question is, what can I do for egress filtering? I want to only allow the minimal amount of traffic out. Do I just "reverse" the rules (i.e. the smtp rule becomes access-list inside_out extended permit tcp host X.Y.Z.1 any eq smtp ) and call it a day, or can I further cull my options? What can I safely block? Furthermore, when doing egress filtering, is it enough to apply "inverted" rules to the outside interface, or should I also look into making dmz_in and inside_in acls? I've heard the term "egress filtering" thrown around a lot, but I don't really know what I'm doing. Any pointers towards good resources and reading would also be helpful, most of the ones I've found presume that I know a lot more than I do.

    Read the article

  • Any problems usinga GoDaddy SSL certificate on a Cisco ASA firewall?

    - by Richard West
    I need to purchase and install a SSL certificate on my Cisco ASA firewall. This will allow my VPN users to connect to my ASA without receiving the certificate error from the untrusted self assigned SSL certificate that is currently on the ASA. I had good experiences with the SSL certificates that GoDaddy sells. However, I'm concerned about using them. On my web servers I have to also install GoDaddy's "intermediate certificate bundle". On the ASA I do not think that I will be able to preform anything like this. I do not fully understand what the "intermediate certificate bundle" does, but obviously it's important. So my question is can I use a GoDaddy SSL certificate on an ASA without my users getting any type of warning or error about connecting to a site that using an untrusted SSL certificate. I need this to be as simple as possible for my end users and warning messages are always scary :) Thanks!

    Read the article

  • ASA 5505 Vlan question

    - by Wayne
    I am setting up a cisco asa 5505 with the base license. I can communicate from inside-outside, outside-inside, inside-home, which is my desired traffic security. I can get http, ssh, and other access from inside-home, but I can't ping from inside-home (192.168.110.0 host to 192.168.7.1 or 192.168.7.0 host). Can someone explain. My config is listed below interface Vlan1<br> nameif inside<br> security-level 100<br> ip address 192.168.110.254 255.255.255.0 <br> !<br> interface Vlan2<br> nameif outside<br> security-level 0<br> pppoe client vpdn group birdie<br> ip address removedIP 255.255.255.255 pppoe <br> !<br> interface Vlan3<br> no forward interface Vlan1<br> nameif home<br> security-level 50<br> ip address 192.168.7.1 255.255.255.0 <br> ! <br> interface Ethernet0/0<br> switchport access vlan 2<br> ! <br> interface Ethernet0/1<br> ! <br> interface Ethernet0/2<br> ! <br> interface Ethernet0/3<br> ! <br> interface Ethernet0/4<br> switchport access vlan 3<br> ! <br> interface Ethernet0/5<br> shutdown <br> ! <br> interface Ethernet0/6<br> shutdown <br> ! <br> interface Ethernet0/7<br> shutdown <br> ! <br> ftp mode passive<br> clock timezone EST -5<br> clock summer-time EDT recurring<br> access-list Outside-In extended permit icmp any any <br> access-list Outside-In extended permit tcp any any eq www <br> access-list Outside-In extended permit tcp any any eq https <br> access-list Outside-In extended permit tcp any any eq 5969 <br> access-list inside_nat0_outbound extended permit ip any 192.168.111.0 255.255.255.224 <br> access-list standardUser_splitTunnelAcl1 extended permit ip 192.168.111.0 255.255.255.0 any <br> access-list standardUser_splitTunnelAcl1 extended permit ip 192.168.110.0 255.255.255.0 <br>any access-list inside_in extended permit icmp any any <br> access-list inside_in extended permit ip any any <br> access-list home_in extended permit icmp any any <br> access-list home_in extended permit ip any any <br> pager lines 24<br> logging enable<br> logging asdm informational<br> mtu inside 1492<br> mtu outside 1492<br> mtu home 1500 <br> ip local pool vpnuser 192.168.111.5-192.168.111.20<br> icmp unreachable rate-limit 1 burst-size 1<br> asdm image disk0:/asdm-524.bin<br> no asdm history enable<br> arp timeout 14400<br> nat-control <br> global (outside) 1 interface<br> nat (inside) 0 access-list inside_nat0_outbound<br> nat (inside) 1 0.0.0.0 0.0.0.0<br> nat (home) 1 192.168.7.0 255.255.255.0<br> static (inside,outside) tcp interface https 192.168.110.6 https netmask 255.255.255.255 <br> static (inside,outside) tcp interface www 192.168.110.6 www netmask 255.255.255.255 <br> static (inside,outside) tcp interface 5969 192.168.110.12 5969 netmask 255.255.255.255 <br> static (inside,home) 192.168.110.0 192.168.110.0 netmask 255.255.255.0 <br> access-group inside_in in interface inside<br> access-group Outside-In in interface outside<br> access-group home_in in interface home<br> route outside 0.0.0.0 0.0.0.0 RemovedIP 1<br>

    Read the article

  • Cisco ASA 5510 shortage?

    - by PHLiGHT
    Has anyone else had problems ordering them recently? Our main vendors have had them out of stock for awhile now and we need to buy a couple. Any known places where they are in stock or why the shortage?

    Read the article

  • ASA and cisco vs NSA sonic firewall

    - by Lbaker101
    Currently I’m trying to structure our network to fully support and be redundant with BGP/Multi homing. Our current company size is 40 employees but the major part of that is our Development department. We are a software company and continued connection to the internet is a requirement as 90% of work stops when the net goes down. The only thing hosted on site (that needs to remain up) is our exchange server. Right now i'm faced with 2 different directions and was wondering if I could get your opinions on this. We will have 2 ISPs that are both 20meg up/down and dedicated fiber (so 40megs combined). This is handed off as an Ethernet cable into our server room. ISP#1 first digital ISP#2 CenturyLink we currently have 2x ASA5505s but the 2nd one is not in use. It was there to be a failover and it just needs the security+ license to be matched with the primary device. But this depends on the network structure. I have been looking into the hardware that would be required to be fully redundant and I found that we will either of the following. 2x Cisco 2921+ series routers with failover licenses. They will go in front of the ASAs and either connects in a failover state or 1 ISP into each of the 2921 series routers and then 1 line into each of the ASAs (thus all 4 hardware components will be used actively). So 2x Cisco 2921+ series routers 2x Cisco ASA5505 firewalls The other route 2x SonicWalls NSA2400MX series. 1 primary and the secondary will be in a failover state. This will remove the ASAs from the network and be about 2k cheaper than the cisco route. This also brings down the points of failure because it’s just the 2x sonicwalls It will also allow us to scale all the way up to 200-400 users (depending on their configuration). This also makes so the Sonic walls. So the real question is with the added functionality ect of the sonicwall is there a point in paying so much more to stay the cisco route? Thanks!

    Read the article

  • problems with ASA 8.4 Nat Rules for a Web Server

    - by Marko
    Having problems with the NAT RULES and Access Rules changes on my ASA5505. Want to straight replace a 5505 with a newer 5505 and unfortunately this means dealing with old version 7.2 and the newer 8.4 configurations. my old NAT RULE: static (inside,outside) WebOutside WebInside netmask 255.255.255.255 and an Access Rule of: access-list outside_access_in extended permit tcp any host WebOutside eq www these dont work in 8.4 I understand there are some changed but I can find little information that makes any sense on how to configure these. Any pointers welcomed.

    Read the article

  • Cisco ASA 5505 inside interface multiple ip addresses

    - by Oneiroi
    I have an issue this morning where I want to be able to assign multiple ip addresses to the inside interface to facilitate an ip range migration for an office. Namely from a 192.168.1.x range to the new range, with the minimum of interruption for those working in the office. (New DHCP leases will use the new range, whilst those still on the 192.168.1.x range can continue to work until their lease is renewed). However I can not for the life of me figure out how to achieve this, trying to create multiple interfaces for the job leads to complaints about the license only allowing 2 active interfaces. Any suggestions? thanks in advance.

    Read the article

  • LOCAL and RADIUS authentication on ASA

    - by ghp
    Have configured local authentication which was working fine.And today I wanted to implement RADIUS too .. but after I have done, Im unable to login to my firewall user-identity default-domain LOCAL aaa authentication ssh console LOCAL and RADIUS aaa-server RADIUS protocol radius aaa-server RADIUS (inside) host xyzabc Key zzzzzz aaa authentication ssh console RADIUS aaa authentication enable console RADIUS aaa authentication http console RADIUS Can someone help me login to my firewall

    Read the article

  • cisco asa + action drop issue

    - by ghp
    Have created a tunnel between 10.x.y.z network and 122.a.b.c ..the tunnel is up and active, but when I try the packet tracer output ..I get the ACTION as drop. I have also enabled same-security-traffic permit intra-interface. Can someone help me what does this drop mean? Result: input-interface: inside input-status: up input-line-status: up output-interface: outside output-status: up output-line-status: up Action: drop Drop-reason: (acl-drop) Flow is denied by configured rule Packet Tracer output @Shane Madden: please find below the packet tracer output. CASA5K-A# CASA5K-A# config t CASA5K-A(config)# packet-tracer input inside tcp 10.x.y.112 0 122.a.b.c 0 Phase: 1 Type: ROUTE-LOOKUP Subtype: input Result: ALLOW Config: Additional Information: in 0.0.0.0 0.0.0.0 outside Phase: 2 Type: ACCESS-LIST Subtype: Result: DROP Config: Implicit Rule Additional Information: Result: input-interface: inside input-status: up input-line-status: up output-interface: outside output-status: up output-line-status: up Action: drop Drop-reason: (acl-drop) Flow is denied by configured rule CASA5K-A(config)# ======================================================================== The access-group are as follows : access-group acl-inbound in interface outside access-group acl-outbound in interface inside and the access-list's are access-list acl-inbound extended permit tcp any any gt 1023 access-list acl-outbound extended permit ip object-group net-Source object net-dest

    Read the article

  • ASA hairpining: I basicaly want to allow 2 spokes to be able to communicate with each other.

    - by Thirst4Knowledge
    ASA Spoke to Spoke Communication I have been looking at spke to spoke comms or "hairpining" for months and have posted on numerouse forums but to no avail. I have a Hub and spoke network where the HUB is an ASA Firewall version 8.2 * I basicaly want to allow 2 spokes to be able to communicate with each other. I think that I have got the concept of the ASA Config for example: same-security-traffic permit intra-interface access-list HQ-LAN extended permit ip ASA-LAN 255.255.248.0 HQ-LAN 255.255.255.0 access-list HQ-LAN extended permit ip 192.168.99.0 255.255.255.0 HQ-LAN 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 HQ-LAN 255.255.255.0 access-list no-nat extended permit ip HQ-LAN 255.255.255.0 192.168.99.0 255.255.255.0 access-list no-nat extended permit ip 192.168.99.0 255.255.255.0 HQ-LAN 255.255.255.0 I think my problem may be that the other spokes are not CIsco Firewalls and I need to work out how to do the alternative setups. I want to at least make sure that my firewall etup is correct then I can move onto the other spokes here is my config: Hostname ASA domain-name mydomain.com names ! interface Ethernet0/0 speed 100 duplex full nameif outside security-level 0 ip address 1.1.1.246 255.255.255.224 ! interface Ethernet0/1 speed 100 duplex full nameif inside security-level 100 ip address 192.168.240.33 255.255.255.224 ! interface Ethernet0/2 description DMZ VLAN-253 speed 100 duplex full nameif DMZ security-level 50 ip address 192.168.254.1 255.255.255.0 ! interface Ethernet0/3 no nameif no security-level no ip address ! boot system disk0:/asa821-k8.bin ftp mode passive clock timezone GMT/BST 0 dns server-group DefaultDNS domain-name mydomain.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network ASA_LAN_Plus_HQ_LAN network-object ASA_LAN 255.255.248.0 network-object HQ-LAN 255.255.255.0 access-list outside_acl remark Exchange web access-list outside_acl extended permit tcp any host MS-Exchange_server-NAT eq https access-list outside_acl remark PPTP Encapsulation access-list outside_acl extended permit gre any host MS-ISA-Server-NAT access-list outside_acl remark PPTP access-list outside_acl extended permit tcp any host MS-ISA-Server-NAT eq pptp access-list outside_acl remark Intra Http access-list outside_acl extended permit tcp any host MS-ISA-Server-NAT eq www access-list outside_acl remark Intra Https access-list outside_acl extended permit tcp any host MS-ISA-Server-NAT eq https access-list outside_acl remark SSL Server-Https 443 access-list outside_acl remark Https 8443(Open VPN Custom port for SSLVPN client downlaod) access-list outside_acl remark FTP 20 access-list outside_acl remark Http access-list outside_acl extended permit tcp any host OpenVPN-Srvr-NAT object-group DM_INLINE_TCP_1 access-list outside_acl extended permit tcp any host OpenVPN-Srvr-NAT eq 8443 access-list outside_acl extended permit tcp any host OpenVPN-Srvr-NAT eq www access-list outside_acl remark For secure remote Managment-SSH access-list outside_acl extended permit tcp any host OpenVPN-Srvr-NAT eq ssh access-list outside_acl extended permit ip Genimage_Anyconnect 255.255.255.0 ASA_LAN 255.255.248.0 access-list ASP-Live remark Live ASP access-list ASP-Live extended permit ip ASA_LAN 255.255.248.0 192.168.60.0 255.255.255.0 access-list Bo remark Bo access-list Bo extended permit ip ASA_LAN 255.255.248.0 192.168.169.0 255.255.255.0 access-list Bill remark Bill access-list Bill extended permit ip ASA_LAN 255.255.248.0 Bill.15 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 Bill.5 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.149.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.160.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.165.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.144.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.140.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.152.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.153.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.163.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.157.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.167.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.156.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 North-Office-LAN 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.161.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.143.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.137.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.159.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 HQ-LAN 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.169.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.150.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.162.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.166.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.168.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.174.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.127.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.173.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.175.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.176.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.100.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.99.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 10.10.10.0 255.255.255.0 access-list no-nat extended permit ip host 192.168.240.34 Cisco-admin-LAN 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 Genimage_Anyconnect 255.255.255.0 access-list no-nat extended permit ip host Tunnel-DC host HQ-SDSL-Peer access-list no-nat extended permit ip HQ-LAN 255.255.255.0 North-Office-LAN 255.255.255.0 access-list no-nat extended permit ip North-Office-LAN 255.255.255.0 HQ-LAN 255.255.255.0 access-list Car remark Car access-list Car extended permit ip ASA_LAN 255.255.248.0 192.168.165.0 255.255.255.0 access-list Che remark Che access-list Che extended permit ip ASA_LAN 255.255.248.0 192.168.144.0 255.255.255.0 access-list Chi remark Chi access-list Chi extended permit ip ASA_LAN 255.255.248.0 192.168.140.0 255.255.255.0 access-list Cla remark Cla access-list Cla extended permit ip ASA_LAN 255.255.248.0 192.168.152.0 255.255.255.0 access-list Eas remark Eas access-list Eas extended permit ip ASA_LAN 255.255.248.0 192.168.149.0 255.255.255.0 access-list Ess remark Ess access-list Ess extended permit ip ASA_LAN 255.255.248.0 192.168.153.0 255.255.255.0 access-list Gat remark Gat access-list Gat extended permit ip ASA_LAN 255.255.248.0 192.168.163.0 255.255.255.0 access-list Hud remark Hud access-list Hud extended permit ip ASA_LAN 255.255.248.0 192.168.157.0 255.255.255.0 access-list Ilk remark Ilk access-list Ilk extended permit ip ASA_LAN 255.255.248.0 192.168.167.0 255.255.255.0 access-list Ken remark Ken access-list Ken extended permit ip ASA_LAN 255.255.248.0 192.168.156.0 255.255.255.0 access-list North-Office remark North-Office access-list North-Office extended permit ip ASA_LAN 255.255.248.0 North-Office-LAN 255.255.255.0 access-list inside_acl remark Inside_ad access-list inside_acl extended permit ip any any access-list Old_HQ remark Old_HQ access-list Old_HQ extended permit ip ASA_LAN 255.255.248.0 HQ-LAN 255.255.255.0 access-list Old_HQ extended permit ip HQ-LAN 255.255.255.0 192.168.99.0 255.255.255.0 access-list She remark She access-list She extended permit ip ASA_LAN 255.255.248.0 192.168.150.0 255.255.255.0 access-list Lit remark Lit access-list Lit extended permit ip ASA_LAN 255.255.248.0 192.168.143.0 255.255.255.0 access-list Mid remark Mid access-list Mid extended permit ip ASA_LAN 255.255.248.0 192.168.137.0 255.255.255.0 access-list Spi remark Spi access-list Spi extended permit ip ASA_LAN 255.255.248.0 192.168.162.0 255.255.255.0 access-list Tor remark Tor access-list Tor extended permit ip ASA_LAN 255.255.248.0 192.168.166.0 255.255.255.0 access-list Tra remark Tra access-list Tra extended permit ip ASA_LAN 255.255.248.0 192.168.168.0 255.255.255.0 access-list Tru remark Tru access-list Tru extended permit ip ASA_LAN 255.255.248.0 192.168.174.0 255.255.255.0 access-list Yo remark Yo access-list Yo extended permit ip ASA_LAN 255.255.248.0 192.168.127.0 255.255.255.0 access-list Nor remark Nor access-list Nor extended permit ip ASA_LAN 255.255.248.0 192.168.159.0 255.255.255.0 access-list Nor extended permit ip ASA_LAN 255.255.248.0 192.168.173.0 255.255.255.0 inactive access-list ST remark ST access-list ST extended permit ip ASA_LAN 255.255.248.0 192.168.175.0 255.255.255.0 access-list Le remark Le access-list Le extended permit ip ASA_LAN 255.255.248.0 192.168.161.0 255.255.255.0 access-list DMZ-ACL remark DMZ access-list DMZ-ACL extended permit ip host OpenVPN-Srvr any access-list no-nat-dmz remark DMZ -No Nat access-list no-nat-dmz extended permit ip 192.168.250.0 255.255.255.0 HQ-LAN 255.255.255.0 access-list Split_Tunnel_List remark ASA-LAN access-list Split_Tunnel_List standard permit ASA_LAN 255.255.248.0 access-list Split_Tunnel_List standard permit Genimage_Anyconnect 255.255.255.0 access-list outside_cryptomap_30 remark Po access-list outside_cryptomap_30 extended permit ip ASA_LAN 255.255.248.0 Po 255.255.255.0 access-list outside_cryptomap_24 extended permit ip ASA_LAN 255.255.248.0 192.168.100.0 255.255.255.0 access-list outside_cryptomap_16 extended permit ip ASA_LAN 255.255.248.0 192.168.99.0 255.255.255.0 access-list outside_cryptomap_34 extended permit ip ASA_LAN 255.255.248.0 10.10.10.0 255.255.255.0 access-list outside_31_cryptomap extended permit ip host 192.168.240.34 Cisco-admin-LAN 255.255.255.0 access-list outside_32_cryptomap extended permit ip host Tunnel-DC host HQ-SDSL-Peer access-list Genimage_VPN_Any_connect_pix_client remark Genimage "Any Connect" VPN access-list Genimage_VPN_Any_connect_pix_client standard permit Genimage_Anyconnect 255.255.255.0 access-list Split-Tunnel-ACL standard permit ASA_LAN 255.255.248.0 access-list nonat extended permit ip HQ-LAN 255.255.255.0 192.168.99.0 255.255.255.0 pager lines 24 logging enable logging timestamp logging console notifications logging monitor notifications logging buffered warnings logging asdm informational no logging message 106015 no logging message 313001 no logging message 313008 no logging message 106023 no logging message 710003 no logging message 106100 no logging message 302015 no logging message 302014 no logging message 302013 no logging message 302018 no logging message 302017 no logging message 302016 no logging message 302021 no logging message 302020 flow-export destination inside MS-ISA-Server 2055 flow-export destination outside 192.168.130.126 2055 flow-export template timeout-rate 1 flow-export delay flow-create 15 mtu outside 1500 mtu inside 1500 mtu DMZ 1500 mtu management 1500 ip local pool RAS-VPN 10.0.0.1.1-10.0.0.1.254 mask 255.255.255.255 icmp unreachable rate-limit 1 burst-size 1 icmp permit any unreachable outside icmp permit any echo outside icmp permit any echo-reply outside icmp permit any outside icmp permit any echo inside icmp permit any echo-reply inside icmp permit any echo DMZ icmp permit any echo-reply DMZ asdm image disk0:/asdm-621.bin no asdm history enable arp timeout 14400 nat-control global (outside) 1 interface global (inside) 1 interface nat (inside) 0 access-list no-nat nat (inside) 1 0.0.0.0 0.0.0.0 nat (DMZ) 0 access-list no-nat-dmz static (inside,outside) MS-ISA-Server-NAT MS-ISA-Server netmask 255.255.255.255 static (DMZ,outside) OpenVPN-Srvr-NAT OpenVPN-Srvr netmask 255.255.255.255 static (inside,outside) MS-Exchange_server-NAT MS-Exchange_server netmask 255.255.255.255 access-group outside_acl in interface outside access-group inside_acl in interface inside access-group DMZ-ACL in interface DMZ route outside 0.0.0.0 0.0.0.0 1.1.1.225 1 route inside 10.10.10.0 255.255.255.0 192.168.240.34 1 route outside Genimage_Anyconnect 255.255.255.0 1.1.1.225 1 route inside Open-VPN 255.255.248.0 OpenVPN-Srvr 1 route inside HQledon-Voice-LAN 255.255.255.0 192.168.240.34 1 route outside Bill 255.255.255.0 1.1.1.225 1 route outside Yo 255.255.255.0 1.1.1.225 1 route inside 192.168.129.0 255.255.255.0 192.168.240.34 1 route outside HQ-LAN 255.255.255.0 1.1.1.225 1 route outside Mid 255.255.255.0 1.1.1.225 1 route outside 192.168.140.0 255.255.255.0 1.1.1.225 1 route outside 192.168.143.0 255.255.255.0 1.1.1.225 1 route outside 192.168.144.0 255.255.255.0 1.1.1.225 1 route outside 192.168.149.0 255.255.255.0 1.1.1.225 1 route outside 192.168.152.0 255.255.255.0 1.1.1.225 1 route outside 192.168.153.0 255.255.255.0 1.1.1.225 1 route outside North-Office-LAN 255.255.255.0 1.1.1.225 1 route outside 192.168.156.0 255.255.255.0 1.1.1.225 1 route outside 192.168.157.0 255.255.255.0 1.1.1.225 1 route outside 192.168.159.0 255.255.255.0 1.1.1.225 1 route outside 192.168.160.0 255.255.255.0 1.1.1.225 1 route outside 192.168.161.0 255.255.255.0 1.1.1.225 1 route outside 192.168.162.0 255.255.255.0 1.1.1.225 1 route outside 192.168.163.0 255.255.255.0 1.1.1.225 1 route outside 192.168.165.0 255.255.255.0 1.1.1.225 1 route outside 192.168.166.0 255.255.255.0 1.1.1.225 1 route outside 192.168.167.0 255.255.255.0 1.1.1.225 1 route outside 192.168.168.0 255.255.255.0 1.1.1.225 1 route outside 192.168.173.0 255.255.255.0 1.1.1.225 1 route outside 192.168.174.0 255.255.255.0 1.1.1.225 1 route outside 192.168.175.0 255.255.255.0 1.1.1.225 1 route outside 192.168.99.0 255.255.255.0 1.1.1.225 1 route inside ASA_LAN 255.255.255.0 192.168.240.34 1 route inside 192.168.124.0 255.255.255.0 192.168.240.34 1 route inside 192.168.50.0 255.255.255.0 192.168.240.34 1 route inside 192.168.51.0 255.255.255.128 192.168.240.34 1 route inside 192.168.240.0 255.255.255.224 192.168.240.34 1 route inside 192.168.240.164 255.255.255.224 192.168.240.34 1 route inside 192.168.240.196 255.255.255.224 192.168.240.34 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server vpn protocol radius max-failed-attempts 5 aaa-server vpn (inside) host 192.168.X.2 timeout 60 key a5a53r3t authentication-port 1812 radius-common-pw a5a53r3t aaa authentication ssh console LOCAL aaa authentication http console LOCAL http server enable http 0.0.0.0 0.0.0.0 inside http 1.1.1.2 255.255.255.255 outside http 1.1.1.234 255.255.255.255 outside http 0.0.0.0 0.0.0.0 management http 1.1.100.198 255.255.255.255 outside http 0.0.0.0 0.0.0.0 outside crypto map FW_Outside_map 1 match address Bill crypto map FW_Outside_map 1 set peer x.x.x.121 crypto map FW_Outside_map 1 set transform-set SECURE crypto map FW_Outside_map 2 match address Bo crypto map FW_Outside_map 2 set peer x.x.x.202 crypto map FW_Outside_map 2 set transform-set SECURE crypto map FW_Outside_map 3 match address ASP-Live crypto map FW_Outside_map 3 set peer x.x.x.113 crypto map FW_Outside_map 3 set transform-set SECURE crypto map FW_Outside_map 4 match address Car crypto map FW_Outside_map 4 set peer x.x.x.205 crypto map FW_Outside_map 4 set transform-set SECURE crypto map FW_Outside_map 5 match address Old_HQ crypto map FW_Outside_map 5 set peer x.x.x.2 crypto map FW_Outside_map 5 set transform-set SECURE WG crypto map FW_Outside_map 6 match address Che crypto map FW_Outside_map 6 set peer x.x.x.204 crypto map FW_Outside_map 6 set transform-set SECURE crypto map FW_Outside_map 7 match address Chi crypto map FW_Outside_map 7 set peer x.x.x.212 crypto map FW_Outside_map 7 set transform-set SECURE crypto map FW_Outside_map 8 match address Cla crypto map FW_Outside_map 8 set peer x.x.x.215 crypto map FW_Outside_map 8 set transform-set SECURE crypto map FW_Outside_map 9 match address Eas crypto map FW_Outside_map 9 set peer x.x.x.247 crypto map FW_Outside_map 9 set transform-set SECURE crypto map FW_Outside_map 10 match address Ess crypto map FW_Outside_map 10 set peer x.x.x.170 crypto map FW_Outside_map 10 set transform-set SECURE crypto map FW_Outside_map 11 match address Hud crypto map FW_Outside_map 11 set peer x.x.x.8 crypto map FW_Outside_map 11 set transform-set SECURE crypto map FW_Outside_map 12 match address Gat crypto map FW_Outside_map 12 set peer x.x.x.212 crypto map FW_Outside_map 12 set transform-set SECURE crypto map FW_Outside_map 13 match address Ken crypto map FW_Outside_map 13 set peer x.x.x.230 crypto map FW_Outside_map 13 set transform-set SECURE crypto map FW_Outside_map 14 match address She crypto map FW_Outside_map 14 set peer x.x.x.24 crypto map FW_Outside_map 14 set transform-set SECURE crypto map FW_Outside_map 15 match address North-Office crypto map FW_Outside_map 15 set peer x.x.x.94 crypto map FW_Outside_map 15 set transform-set SECURE crypto map FW_Outside_map 16 match address outside_cryptomap_16 crypto map FW_Outside_map 16 set peer x.x.x.134 crypto map FW_Outside_map 16 set transform-set SECURE crypto map FW_Outside_map 16 set security-association lifetime seconds crypto map FW_Outside_map 17 match address Lit crypto map FW_Outside_map 17 set peer x.x.x.110 crypto map FW_Outside_map 17 set transform-set SECURE crypto map FW_Outside_map 18 match address Mid crypto map FW_Outside_map 18 set peer 78.x.x.110 crypto map FW_Outside_map 18 set transform-set SECURE crypto map FW_Outside_map 19 match address Sp crypto map FW_Outside_map 19 set peer x.x.x.47 crypto map FW_Outside_map 19 set transform-set SECURE crypto map FW_Outside_map 20 match address Tor crypto map FW_Outside_map 20 set peer x.x.x.184 crypto map FW_Outside_map 20 set transform-set SECURE crypto map FW_Outside_map 21 match address Tr crypto map FW_Outside_map 21 set peer x.x.x.75 crypto map FW_Outside_map 21 set transform-set SECURE crypto map FW_Outside_map 22 match address Yo crypto map FW_Outside_map 22 set peer x.x.x.40 crypto map FW_Outside_map 22 set transform-set SECURE crypto map FW_Outside_map 23 match address Tra crypto map FW_Outside_map 23 set peer x.x.x.145 crypto map FW_Outside_map 23 set transform-set SECURE crypto map FW_Outside_map 24 match address outside_cryptomap_24 crypto map FW_Outside_map 24 set peer x.x.x.46 crypto map FW_Outside_map 24 set transform-set SECURE crypto map FW_Outside_map 24 set security-association lifetime seconds crypto map FW_Outside_map 25 match address Nor crypto map FW_Outside_map 25 set peer x.x.x.70 crypto map FW_Outside_map 25 set transform-set SECURE crypto map FW_Outside_map 26 match address Ilk crypto map FW_Outside_map 26 set peer x.x.x.65 crypto map FW_Outside_map 26 set transform-set SECURE crypto map FW_Outside_map 27 match address Nor crypto map FW_Outside_map 27 set peer x.x.x.240 crypto map FW_Outside_map 27 set transform-set SECURE crypto map FW_Outside_map 28 match address ST crypto map FW_Outside_map 28 set peer x.x.x.163 crypto map FW_Outside_map 28 set transform-set SECURE crypto map FW_Outside_map 28 set security-association lifetime seconds crypto map FW_Outside_map 28 set security-association lifetime kilobytes crypto map FW_Outside_map 29 match address Lei crypto map FW_Outside_map 29 set peer x.x.x.4 crypto map FW_Outside_map 29 set transform-set SECURE crypto map FW_Outside_map 30 match address outside_cryptomap_30 crypto map FW_Outside_map 30 set peer x.x.x.34 crypto map FW_Outside_map 30 set transform-set SECURE crypto map FW_Outside_map 31 match address outside_31_cryptomap crypto map FW_Outside_map 31 set pfs crypto map FW_Outside_map 31 set peer Cisco-admin-Peer crypto map FW_Outside_map 31 set transform-set ESP-AES-256-SHA crypto map FW_Outside_map 32 match address outside_32_cryptomap crypto map FW_Outside_map 32 set pfs crypto map FW_Outside_map 32 set peer HQ-SDSL-Peer crypto map FW_Outside_map 32 set transform-set ESP-AES-256-SHA crypto map FW_Outside_map 34 match address outside_cryptomap_34 crypto map FW_Outside_map 34 set peer x.x.x.246 crypto map FW_Outside_map 34 set transform-set ESP-AES-128-SHA ESP-AES-192-SHA ESP-AES-256-SHA crypto map FW_Outside_map 65535 ipsec-isakmp dynamic dynmap crypto map FW_Outside_map interface outside crypto map FW_outside_map 31 set peer x.x.x.45 crypto isakmp identity address crypto isakmp enable outside crypto isakmp policy 9 webvpn enable outside svc enable group-policy ASA-LAN-VPN internal group-policy ASA_LAN-VPN attributes wins-server value 192.168.x.1 192.168.x.2 dns-server value 192.168.x.1 192.168.x.2 vpn-tunnel-protocol IPSec svc split-tunnel-policy tunnelspecified split-tunnel-network-list value Split-Tunnel-ACL default-domain value MYdomain username xxxxxxxxxx password privilege 15 tunnel-group DefaultRAGroup ipsec-attributes isakmp keepalive threshold 30 retry 2 tunnel-group DefaultWEBVPNGroup ipsec-attributes isakmp keepalive threshold 30 retry 2 tunnel-group x.x.x.121 type ipsec-l2l tunnel-group x.x.x..121 ipsec-attributes pre-shared-key * isakmp keepalive threshold 30 retry 2 tunnel-group x.x.x.202 type ipsec-l2l tunnel-group x.x.x.202 ipsec-attributes pre-shared-key * isakmp keepalive threshold 30 retry 2 tunnel-group x.x.x.113 type ipsec-l2l tunnel-group x.x.x.113 ipsec-attributes pre-shared-key * isakmp keepalive threshold 30 retry 2 tunnel-group x.x.x.205 type ipsec-l2l tunnel-group x.x.x.205 ipsec-attributes pre-shared-key * isakmp keepalive threshold 30 retry 2 tunnel-group x.x.x.204 type ipsec-l2l tunnel-group x.x.x.204 ipsec-attributes pre-shared-key * isakmp keepalive threshold 30 retry 2 tunnel-group x.x.x.212 type ipsec-l2l tunnel-group x.x.x.212 ipsec-attributes pre-shared-key * tunnel-group x.x.x.215 type ipsec-l2l tunnel-group x.x.x.215 ipsec-attributes pre-shared-key * tunnel-group x.x.x.247 type ipsec-l2l tunnel-group x.x.x.247 ipsec-attributes pre-shared-key * tunnel-group x.x.x.170 type ipsec-l2l tunnel-group x.x.x.170 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x..8 type ipsec-l2l tunnel-group x.x.x.8 ipsec-attributes pre-shared-key * tunnel-group x.x.x.212 type ipsec-l2l tunnel-group x.x.x.212 ipsec-attributes pre-shared-key * tunnel-group x.x.x.230 type ipsec-l2l tunnel-group x.x.x.230 ipsec-attributes pre-shared-key * tunnel-group x.x.x.24 type ipsec-l2l tunnel-group x.x.x.24 ipsec-attributes pre-shared-key * tunnel-group x.x.x.46 type ipsec-l2l tunnel-group x.x.x.46 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x.4 type ipsec-l2l tunnel-group x.x.x.4 ipsec-attributes pre-shared-key * tunnel-group x.x.x.110 type ipsec-l2l tunnel-group x.x.x.110 ipsec-attributes pre-shared-key * tunnel-group 78.x.x.110 type ipsec-l2l tunnel-group 78.x.x.110 ipsec-attributes pre-shared-key * tunnel-group x.x.x.47 type ipsec-l2l tunnel-group x.x.x.47 ipsec-attributes pre-shared-key * tunnel-group x.x.x.34 type ipsec-l2l tunnel-group x.x.x.34 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x..129 type ipsec-l2l tunnel-group x.x.x.129 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x.94 type ipsec-l2l tunnel-group x.x.x.94 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x.40 type ipsec-l2l tunnel-group x.x.x.40 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x.65 type ipsec-l2l tunnel-group x.x.x.65 ipsec-attributes pre-shared-key * tunnel-group x.x.x.70 type ipsec-l2l tunnel-group x.x.x.70 ipsec-attributes pre-shared-key * tunnel-group x.x.x.134 type ipsec-l2l tunnel-group x.x.x.134 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x.163 type ipsec-l2l tunnel-group x.x.x.163 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x.2 type ipsec-l2l tunnel-group x.x.x.2 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group ASA-LAN-VPN type remote-access tunnel-group ASA-LAN-VPN general-attributes address-pool RAS-VPN authentication-server-group vpn authentication-server-group (outside) vpn default-group-policy ASA-LAN-VPN tunnel-group ASA-LAN-VPN ipsec-attributes pre-shared-key * tunnel-group x.x.x.184 type ipsec-l2l tunnel-group x.x.x.184 ipsec-attributes pre-shared-key * tunnel-group x.x.x.145 type ipsec-l2l tunnel-group x.x.x.145 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x.75 type ipsec-l2l tunnel-group x.x.x.75 ipsec-attributes pre-shared-key * tunnel-group x.x.x.246 type ipsec-l2l tunnel-group x.x.x.246 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x.2 type ipsec-l2l tunnel-group x.x.x..2 ipsec-attributes pre-shared-key * tunnel-group x.x.x.98 type ipsec-l2l tunnel-group x.x.x.98 ipsec-attributes pre-shared-key * ! ! ! policy-map global_policy description Netflow class class-default flow-export event-type all destination MS-ISA-Server policy-map type inspect dns migrated_dns_map_1 parameters message-length maximum 512 Anyone have a clue because Im on the verge of going postal.....

    Read the article

  • ASA 5505 VPN setup. VPN works but still unable to reach devices in the inside network.

    - by chickenloop
    I've setup a Remote Access VPN on my Cisco ASA 5505. I'm able to connect to my ASA via my phone or the Cisco client, but I'm unable to reach devices in my inside LAN when connected via VPN. The setup is the following: Inside Network : 10.0.0.0/24 VPN_POOL: 172.16.0.0/24 Outside Network: 192.168.1.0/24 ASA is not the perimeter router, there is another device on the 192.168.1.0/24 network which is connected to my cable provider. Obviously UDP port 500 and 4500 are forwarded to the ASA's outside interface. Everything works perfectly, besides the VPN stuff. Config: interface Vlan1 nameif inside security-level 100 ip address 10.0.0.254 255.255.255.0 interface Vlan2 description Outside Interface nameif outside security-level 0 address 192.168.1.254 255.255.255.0 object network VPNPOOL subnet 172.16.0.0 255.255.255.0 object network INSIDE_LAN subnet 10.0.0.0 255.255.255.0 Then the exempt NAT rule. nat (inside,outside) source static INSIDE_LAN INSIDE_LAN destination static VPNPOOL VPNPOOL I don't think that the problem is with the VPN config, as I can successfully establish the VPN connection, but just in case I post it here: group-policy ZSOCA_ASA internal group-policy ZSOCA_ASA attributes vpn-tunnel-protocol ikev1 split-tunnel-policy tunnelspecified split-tunnel-network-list value Split-Tunnel default-domain value default.domain.invalid tunnel-group ZSOCA_ASA type remote-access tunnel-group ZSOCA_ASA general-attributes address-pool VPNPOOL default-group-policy ZSOCA_ASA tunnel-group ZSOCA_ASA ipsec-attributes ikev1 pre-shared-key ***** Any ideas are welcome. Regards.

    Read the article

  • Cisco Catalyst 3750 connected to Cisco ASA 5505 and dropping packets

    - by Bo102010
    (Cross posted from Super User per suggestion there) At the office, I have inherited a network that I am still trying to fully comprehend. I have a problem today with a new connection between: A port on a Cisco Catalyst 3750 [WS-C3750G-48TS-S running C3750-IPSERVICESK9-M version 12.2(53)SE1] A port on a Cisco ASA 5505 [ASA Software version 8.3(2)] The 3750 is home to a Vlan that has a few ports assigned to it. interface Vlan3 description Internal network (172.18.160.0/24) ip address 172.18.160.1 255.255.255.0 I have a host (outside of my control) that needs to be in this VLAN (i.e it must have an address 172.18.160.something/24) that also needs to access the Internet. To accomplish this, I ran a link from the Catalyst (Gi1/0/13) to the ASA (Ethernet 0/5). I configured the Catalyst port like so: interface GigabitEthernet1/0/13 description To ASA, 172.18.160.69 switchport access vlan 3 switchport mode access speed 100 duplex full I configured the ASA like so: interface Vlan1 nameif inside security-level 100 ip address 172.18.160.69 255.255.255.0 interface Ethernet0/5 speed 100 duplex full Then I plugged the host into Ethernet 0/4 on the ASA and instructed its owner to make its default gateway 172.18.160.69. I made a NAT rule in the ASA and set up some rules, and it's able to access the Internet without issue. However, I noticed that the Catalyst reports a ton of packets being dropped toward the ASA. Catalyst3750#show interfaces GigabitEthernet 1/0/13 | include counters|drops Last clearing of "show interface" counters 00:28:13 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 136909347 This is a huge number of drops, since there's not much traffic on this VLAN at all. I tried these things: Make sure speed and duplex agree on both sides (100 Mbps / Full) Set no cdp enable on the Catalyst Gi10/13 Set no keepalive on the Catalyst Gi10/13 Checked for excessive CPU usage on both Checked for excessive traffic on both Am I missing something? Any help would be appreciated.

    Read the article

  • Cisco training basic, entry, ASA/PIX. Help to understand network

    - by Inbr3d
    I need to learn how to configure Cisco ASA/PIX boxes within my network. I have the task to impliment a new ASA 5505 into a new site we purchased. I have over 9 devices linking my sites together and with no support from the previous IT company im finding it hard to get to terms with what they can do and what they are currently doing. I know there are hundreds of guides how to configure them but into an existing environment? can anyone recommend courses within the UK that can help me? Im not much of a book reader, i would need to be able to manage my network after. also, should i seek external contracts to support these devices? as they are critical for our work. thanks

    Read the article

  • Exposing the AnyConnect HTTPS service to outside network

    - by Maciej Swic
    We have a Cisco ASA 5505 with firmware ASA9.0(1) and ASDM 7.0(2). It is configured with a public ip address, and when trying to reach it from the outside by HTTPS for AnyConnect VPN, we get the following log output: 6 Nov 12 2012 07:01:40 <client-ip> 51000 <asa-ip> 443 Built inbound TCP connection 2889 for outside:<client-ip>/51000 (<client-ip>/51000) to identity:<asa-ip>/443 (<asa-ip>/443) 6 Nov 12 2012 07:01:40 <client-ip> 50999 <asa-ip> 443 Built inbound TCP connection 2890 for outside:<client-ip>/50999 (<client-ip>/50999) to identity:<asa-ip>/443 (<asa-ip>/443) 6 Nov 12 2012 07:01:40 <client-ip> 51000 <asa-ip> 443 Teardown TCP connection 2889 for outside:<client-ip>/51000 to identity:<asa-ip>/443 duration 0:00:00 bytes 0 No valid adjacency 6 Nov 12 2012 07:01:40 <client-ip> 50999 <asa-ip> 443 Teardown TCP connection 2890 for outside:<client-ip>/50999 to identity:<asa-ip>/443 duration 0:00:00 bytes 0 No valid adjacency We finished the startup wizard and the anyconnect vpn wizard and here is the resulting configuration: Cryptochecksum: 12262d68 23b0d136 bb55644a 9c08f86b : Saved : Written by enable_15 at 07:08:30.519 UTC Mon Nov 12 2012 ! ASA Version 9.0(1) ! hostname vpn domain-name office.<redacted>.com enable password <redacted> encrypted passwd <redacted> encrypted names ip local pool vpn-pool 192.168.67.2-192.168.67.253 mask 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.68.250 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address <redacted> 255.255.255.248 ! ftp mode passive dns server-group DefaultDNS domain-name office.<redacted>.com object network obj_any subnet 0.0.0.0 0.0.0.0 pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu inside 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 no arp permit-nonconnected ! object network obj_any nat (inside,outside) dynamic interface timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy user-identity default-domain LOCAL http server enable http 192.168.68.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto ipsec security-association pmtu-aging infinite crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map inside_map interface inside crypto ca trustpoint _SmartCallHome_ServerCA crl configure crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=vpn proxy-ldc-issuer crl configure crypto ca trustpool policy crypto ca certificate chain _SmartCallHome_ServerCA certificate ca 6ecc7aa5a7032009b8cebcf4e952d491 <redacted> quit crypto ca certificate chain ASDM_TrustPoint0 certificate f678a050 <redacted> quit crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 enable outside client-services port 443 crypto ikev2 remote-access trustpoint ASDM_TrustPoint0 telnet timeout 5 ssh 192.168.68.0 255.255.255.0 inside ssh timeout 5 console timeout 0 vpn-addr-assign local reuse-delay 60 dhcpd auto_config outside ! dhcpd address 192.168.68.254-192.168.68.254 inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ssl trust-point ASDM_TrustPoint0 inside ssl trust-point ASDM_TrustPoint0 outside webvpn enable outside enable inside anyconnect image disk0:/anyconnect-win-3.1.01065-k9.pkg 1 anyconnect image disk0:/anyconnect-linux-3.1.01065-k9.pkg 2 anyconnect image disk0:/anyconnect-macosx-i386-3.1.01065-k9.pkg 3 anyconnect profiles GM-AnyConnect_client_profile disk0:/GM-AnyConnect_client_profile.xml anyconnect enable tunnel-group-list enable group-policy GroupPolicy_GM-AnyConnect internal group-policy GroupPolicy_GM-AnyConnect attributes wins-server none dns-server value 192.168.68.254 vpn-tunnel-protocol ikev2 ssl-client default-domain value office.<redacted>.com webvpn anyconnect profiles value GM-AnyConnect_client_profile type user username <redacted> password <redacted> encrypted tunnel-group GM-AnyConnect type remote-access tunnel-group GM-AnyConnect general-attributes address-pool vpn-pool default-group-policy GroupPolicy_GM-AnyConnect tunnel-group GM-AnyConnect webvpn-attributes group-alias GM-AnyConnect enable ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global prompt hostname context call-home reporting anonymous Cryptochecksum:12262d6823b0d136bb55644a9c08f86b : end Clearly we are missing something, but the question is, what?

    Read the article

  • How do you change a Cisco ASA 5510 management interface?

    - by Sam Sanders
    I want to add a redundant interface to my Cisco ASA 5510. The management interface is currently using Ethernet0/1 (10.1.25.254/24) one of the interface I want to use for the redundant interfaces. So I wanted to setup Management0/0 as the new management interface. The other interface I want to use is Ethernet0/2 (10.1.0.254/24) for the redundant interface. The Ethernet0/3 (10.1.251.5/24) interface is not going to be part of the redundant interface. I gave the Management0/0 an IP address of 10.1.254.5, and was able to connect a win7 box to Management0/0 and use 10.1.254.5 as a gateway; and ping another address on the (10.1.251.0/24) network, but I can't ping the interface (10.1.254.5) itself. I also can't use ASDM/SSH to log onto the ASA at 10.1.254.5. I setup rules in Configuration Device Management Management Access ASDM/HTTPS/Telnet/SSH. That look like the original rules for the Ethernet0/1 interface. The last thing I can think to try would be to change the Configuration Device Management Management Access Management Interface. I'm a bit nervous about changing it, the description of it is a bit vague. What it's going to do if I change it? What is the correct way to change a management interface?

    Read the article

  • ASA DHCP Relay configuration..

    - by Jeff
    I have locations in different cities, connected using 2 Cisco ASA devices. my main location, corporate, use the IP 192.168.1.x The second location, remote store, use the IP 192.168.3.x I have a DHCP server (192.168.1.254) at my corporate location. I have created a scope for the 192.168.1.x which works fine for the corporate location. I created a scope for the remote location (192.168.3.x) on my DHCP server and tried to configure the remote ASA DCHP Relay, on the remote ASA: I disabled the DHCP Server on the inside. I enabled DHCP Relay on the inside, with set route set at yes. I set the Global DHCP Relay Servers, specify up to four servers to which DHCP requests would be relayed. I added my DHCP, 192.168.1.254 I flashed these settings to the ASA and gave it a try, didn't do anything. am i missing something - forgetting something. not really sure what im doing wrong. DHCP Settings on remote ASA: dhcp-client update dns server both dhcpd dns 192.168.1.254 dhcpd ping_timeout 750 dhcpd domain JEWELS.LOCAL dhcpd auto_config outside dhcpd update dns both ! dhcpd address 192.168.3.2-192.168.3.33 inside ! dhcprelay server 192.168.1.254 outside dhcprelay enable inside dhcprelay setroute inside on my local ASA: i have two ACLs for UDP ports 67 and 68 permitting any inbound traffic from the remote locations IP ... dhcprelay timeout 120

    Read the article

  • Cisco FWSM -> ASA upgrade broke our mail server

    - by Mike Pennington
    We send mail with unicode asian characters to our mail server on the other side of our WAN... immediately after upgrading from a FWSM running 2.3(2) to an ASA5550 running 8.2(5), we saw failures on mail jobs that contained unicode. The symptoms are pretty clear... using the ASA's packet capture utility, we snagged the traffic before and after it left the ASA... access-list PCAP line 1 extended permit tcp any host 192.0.2.25 eq 25 capture pcap_inside type raw-data access-list PCAP buffer 1500000 packet-length 9216 interface inside capture pcap_outside type raw-data access-list PCAP buffer 1500000 packet-length 9216 interface WAN I downloaded the pcaps from the ASA by going to https://<fw_addr>/pcap_inside/pcap and https://<fw_addr>/pcap_outside/pcap... when I looked at them with Wireshark Follow TCP Stream, the inside traffic going into the ASA looks like this EHLO metabike AUTH LOGIN YzFwbUlciXNlck== cZUplCVyXzRw But the same mail leaving the ASA on the outside interface looks like this... EHLO metabike AUTH LOGIN YzFwbUlciXNlck== XXXXXXXXXXXX The XXXX characters are concerning... I fixed the issue by disabling ESMTP inspection: wan-fw1(config)# policy-map global_policy wan-fw1(config-pmap)# class inspection_default wan-fw1(config-pmap-c)# no inspect esmtp wan-fw1(config-pmap-c)# end The $5 question... our old FWSM used SMTP fixup without issues... mail went down at the exact moment that we brought the new ASAs online... what specifically is different about the ASA that it is now breaking this mail? Note: usernames / passwords / app names were changed... don't bother trying to Base64-decode this text.

    Read the article

  • Is it possible to do DNS-based ACLs on a Cisco ASA?

    - by pickles
    Short of using static IP addresses, is it possible to have a Cisco ASA use a DNS name rather than an IP address? For instance, if I want to limit a host in the DMZ to access only one particular web service, but that web service might be globally load balanced or using DynDNS or cloud, how can the ACL be expressed so that a fixed IP address isn't used and the admin doesn't have to keep opening and closing down IP addresses?

    Read the article

  • How can I forward all web traffic from my Cisco ASA 5100 to a checkpoint firewall?

    - by Scott Clements
    Hi, I currently have two Cisco ASA 5100 routers setup with a site-to-site VPN at different physical locations. They are successfully configured so that all traffic at our remote site is forwarded over this VPN tunnel to our router here, which is fine, however I need the web traffic that comes here to then be forwarded onto our Check Point firewall router. Can someone please tell me how I can configure this?? Many Thanks, Scott

    Read the article

  • How can I forward ALL traffic over a site-to-site VPN on Cisco ASA?

    - by Scott Clements
    Hi There, I currently have two Cisco ASA 5100 routers. They are at different physical sites and are configured with a site-to-site VPN which is active and working. I can communicate with the subnets on either site from the other and both are connected to the internet, however I need to ensure that all the traffic at my remote site goes through this VPN to my site here. I know that the web traffic is doing so as a "tracert" confirms this, but I need to ensure that all other network traffic is being directed over this VPN to my network here. Here is my config for the ASA router at my remote site: hostname ciscoasa domain-name xxxxx enable password 78rl4MkMED8xiJ3g encrypted names ! interface Ethernet0/0 nameif NIACEDC security-level 100 ip address x.x.x.x 255.255.255.0 ! interface Ethernet0/1 description External Janet Connection nameif JANET security-level 0 ip address x.x.x.x 255.255.255.248 ! interface Ethernet0/2 shutdown no nameif security-level 100 no ip address ! interface Ethernet0/3 shutdown no nameif security-level 100 ip address dhcp setroute ! interface Management0/0 nameif management security-level 100 ip address 192.168.100.1 255.255.255.0 management-only ! passwd 2KFQnbNIdI.2KYOU encrypted ftp mode passive clock timezone GMT/BST 0 clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00 dns domain-lookup NIACEDC dns server-group DefaultDNS name-server 154.32.105.18 name-server 154.32.107.18 domain-name XXXX same-security-traffic permit inter-interface same-security-traffic permit intra-interface access-list ren_access_in extended permit ip any any access-list ren_access_in extended permit tcp any any access-list ren_nat0_outbound extended permit ip 192.168.6.0 255.255.255.0 192.168.3.0 255.255.255.0 access-list NIACEDC_nat0_outbound extended permit ip 192.168.12.0 255.255.255.0 192.168.3.0 255.255.255.0 access-list JANET_20_cryptomap extended permit ip 192.168.12.0 255.255.255.0 192.168.3.0 255.255.255.0 access-list NIACEDC_access_in extended permit ip any any access-list NIACEDC_access_in extended permit tcp any any access-list JANET_access_out extended permit ip any any access-list NIACEDC_access_out extended permit ip any any pager lines 24 logging enable logging asdm informational mtu NIACEDC 1500 mtu JANET 1500 mtu management 1500 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-522.bin no asdm history enable arp timeout 14400 nat-control global (NIACEDC) 1 interface global (JANET) 1 interface nat (NIACEDC) 0 access-list NIACEDC_nat0_outbound nat (NIACEDC) 1 192.168.12.0 255.255.255.0 access-group NIACEDC_access_in in interface NIACEDC access-group NIACEDC_access_out out interface NIACEDC access-group JANET_access_out out interface JANET route JANET 0.0.0.0 0.0.0.0 194.82.121.82 1 route JANET 0.0.0.0 0.0.0.0 192.168.3.248 tunneled timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout uauth 0:05:00 absolute http server enable http 192.168.12.0 255.255.255.0 NIACEDC http 192.168.100.0 255.255.255.0 management http 192.168.9.0 255.255.255.0 NIACEDC no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto map JANET_map 20 match address JANET_20_cryptomap crypto map JANET_map 20 set pfs crypto map JANET_map 20 set peer X.X.X.X crypto map JANET_map 20 set transform-set ESP-AES-256-SHA crypto map JANET_map interface JANET crypto isakmp enable JANET crypto isakmp policy 10 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 30 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 50 authentication pre-share encryption aes-256 hash sha group 5 lifetime 86400 tunnel-group X.X.X.X type ipsec-l2l tunnel-group X.X.X.X ipsec-attributes pre-shared-key * telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd address 192.168.100.2-192.168.100.254 management dhcpd enable management ! ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect http ! service-policy global_policy global prompt hostname context no asdm history enable Thanks in advance, Scott

    Read the article

  • Cisco ASA log error "regular translation creation failed for icmp ..."

    - by Martijn Heemels
    Every few seconds our new Cisco ASA 5505 firewall is logging errors that I can't figure out with my limited Cisco experience. Severity Date Time Syslog ID Source IP Destination IP Description 3 Mar 25 2010 17:21:14 305006 8.8.8.8 regular translation creation failed for icmp src inside:10.10.0.200 dst outside:8.8.8.8 (type 3, code 3) 3 Mar 25 2010 17:18:37 305006 8.8.4.4 regular translation creation failed for icmp src inside:10.10.0.200 dst outside:8.8.4.4 (type 3, code 3) The logged inside IP is our internal DNS resolver, and the outside IP's are Google's public DNS servers. ICMP Type 3 Code 3 means "Port Unreachable" Our "outside" interface has a fixed IP and our "inside" interface is in the 10.10.0.0/16 subnet. The 'Inspect DNS' Service Policy is enabled, with the preset DNS inspection map. Furthermore there's an ACL that allows all inbound ICMP on the "outside" interface. I've spent hours trying to figure this one out, so any and all advice is welcome!

    Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10  | Next Page >