Search Results

Search found 21131 results on 846 pages for 'binary log'.

Page 402/846 | < Previous Page | 398 399 400 401 402 403 404 405 406 407 408 409  | Next Page >

  • External USB HD issues with a twist (works on Windows7 but not XP)

    - by Eruditass
    I have this older external USB HD, 160 GB. I was using it to copy my Steam games to another computer. On the source computer, Windows 7 64-bit, everything worked fine. Drive reported no errors, had no hiccups, etc. Plugging it into the Windows XP 32-bit computer, it worked fine for looking through the files, moving files around on it (no real reading/writing, just modifying the filesystem table). However, when copying files from it to my internal HD, after a couple seconds to tens of minutes (seemingly random times), the USB device becomes unrecognized and it reports a delayed write error. Events in system log go like this, chronologically: (number times displayed)xSource (Event ID): "message" 2xdisk (51): An error was detected on device \Device\Harddisk1\D during a paging operation. 1xftdisk (57): The system failed to flush data to the transaction log. Corruption may occur. 1xApplication popup (26): Windows - Delayed Write Failed : Windows was unable to save all the data for the file E:\$Mft. The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. 1xntfs (50): {Delayed Write Failed} Windows was unable to save all the data for the file . The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. These repeat for a while, then there is 10+ disk messages or ftdisk messages. Other notes: This occurs on random files at random times. This problem cannot be replicated on the Windows 7 source machine when copying from the HD to a different location on its local disk chkdsk /f was run and found no errors. chkdsk /f/r has the delayed write issue. drive was set to quick removal. Setting to performance in device manager yielded same result I am not writing anything to the USB external drive, so I am not sure why there is even a delayed write error (writing file access times?) local Windows XP was chkdsk'd without problems Windows XP machine has no problems with other USB HD's Various USB ports were attempted Rebooting did not help Occurs with SyncToy as well as windows explorer SMART status is good on both local drive and the external one Lack of gaming is making me cranky

    Read the article

  • Weblog analyzer most useful features

    - by phq
    There are already a lot of questions asking which analyzer is the best. I try here to invert the question. Instead of asking which analyzer has the best features I'm looking for what are the best features. More interesting is to separate what an analyzer can do from what is useful spending time doing. What are the most useful features I should look for in a web server log analyzer? How are they useful, what problems can they solve?

    Read the article

  • Configure Local Mail on Ubuntu

    - by Eric J.
    My cron jobs are trying to mail their results using the local mail feature of Ubuntu (not internet email, the kind of mail you can read with mutt). However, /var/log/syslog reports /USR/SBIN/CRON[19212]: (speedtax) MAIL (mailed 52 bytes of output but got status 0x0006 ) I would like to setup local mail (so that cron can deliver the output successfully) but do not want to setup internet email. Everything I find on google is about the latter.

    Read the article

  • Splunk is fantastically expensive: What are the alternatives? [closed]

    - by samsmith
    Possible Duplicate: Alternatives to Splunk? This has been discussed, but it has been several months, so it may be time to revisit it: Earlier discussion RE Splunk alternatives For the record, Splunk rocks. But the pricing is simply beyond what we can consider (When I spoke with Splunk today, the cost for a system to index 5gb/day of data is over $30,000.) That is more than we spend on SQL Server (by a large multiple), more than we spend on a rack of servers (by a multiple), etc. etc. The splunk sales team is correct (that for $30K we get more value and functionality than if we spend the same building our own system), but it doesn't matter. The splunk cost is simply too high (by a multiple). Soooooo, we are looking around! Is anyone out there building a splunk like system? Our basic need: Able to listen for syslog messages on multiple udp ports Able to index the incoming data in an async way Some kind of search engine Some kind of UI An API to the search engine (to embed in our console) We currently need to index 3-5gb/day, but need to be able to scale to 10gb/day or more. We do not need a lot of history (30 days is fine). We use Windows 2008 and 2003 servers. Thanks for your thoughts! UPDATE: We spent two weeks researching commercial and open source options. Our conclusion: Write our own (we are a software company... we know how to write things). We built a great system built on mongodb and .NET that gives us the functions we needed from MongoDB in about one engineering week. We have now completed our implementation. We use two Mongodb servers (master and slave), and are able to log and index any amount of log data (5gb/day, 15gb/day, etc), limited only by disk space. OBSERVATIONS: This space needs a solid solution that is $1000-3000 flat rate. The licensing models used by the commercial firms are based on a "milk the data center ops guys" models. That is their right (of course!), but it leaves a HUGE space open for someone to come in underneath them. My guess is that in another year or two there will be a good open source solution that will be really usable. Thank you all for your input (even if it was self promotion).

    Read the article

  • Move Firefox user settings to another folder on same machine

    - by Jesper Rønn-Jensen
    Due to company restrictions where I currently work, My windows users folder %USERPROFILE% is space restricted. I get a warning that I must delete files before I can log off. Because of that, I have moved everything else out of my profile folder (maven repository, IntelliJ configuration & cache). I need to tell Firefox to put userprofiles somewhere else on my machine (like for instance C:\ff_profiles\ ). How do I do that?

    Read the article

  • Problem installing SQL Server client tools

    - by Shiraz Bhaiji
    We are tring to install SQL Server 2005 Standard on Windows 2008 Standard both 64 bit. Have done this before with no problems. This time we get an error during the installation of client tools: There was an unexpected failure during the setup wizard Link Id 20476, message ID 50000 There are no errors in the event log. Anybody have any ideas what could be wrong?

    Read the article

  • McAfee VirusScan for Mac OS X logs 'getgrnam("Virex")' error every 10 seconds

    - by crb
    Every 10 seconds, something like the following appears in the Mac OS X system log: 17/12/2009 14:51:11 com.apple.launchd[1] (com.mcafee.virusscan.ScanManager[20499]) getgrnam("Virex") failed 17/12/2009 14:51:11 com.apple.launchd[1] (com.mcafee.virusscan.ScanManager[20499]) Exited with exit code: 1 17/12/2009 14:51:11 com.apple.launchd[1] (com.mcafee.virusscan.ScanManager) Throttling respawn: Will start in 10 seconds 17/12/2009 14:51:13 com.apple.launchd[1] (com.mcafee.virusscan.VShieldEPOInterface[20500]) getgrnam("Virex") failed 17/12/2009 14:51:13 com.apple.launchd[1] (com.mcafee.virusscan.VShieldEPOInterface[20500]) Exited with exit code: 1 17/12/2009 14:51:13 com.apple.launchd[1] (com.mcafee.virusscan.VShieldEPOInterface) Throttling respawn: Will start in 10 seconds

    Read the article

  • how do i lock down my preferences for Services .mmc snapin column layout and view type

    - by gerryLowry
    when "Services" opens, it's in Extended View. i prefer Standard view. i also prefer this column layout: Status | Startup Type | Log On As | Name | Description because when I expand all columns via Ctrl+(numeric keypad "+") what i need to see most i can view without being forced to scroll to the right. Problem: my preferred layout does not persist. QUESTION: how can i force Windows (2008 R2, 7, XP, et cetera) to remmember my settings? thnx / g.

    Read the article

  • Rails 3 shows 404 error instead of index.html (nginx + unicorn)

    - by Miko
    I have an index.html in public/ that should be loading by default but instead I get a 404 error when I try to access http://example.com/ The page you were looking for doesn't exist. You may have mistyped the address or the page may have moved. This has something to do with nginx and unicorn which I am using to power Rails 3 When take unicorn out of the nginx configuration file, the problem goes away and index.html loads just fine. Here is my nginx configuration file: upstream unicorn { server unix:/tmp/.sock fail_timeout=0; } server { server_name example.com; root /www/example.com/current/public; index index.html; keepalive_timeout 5; location / { try_files $uri @unicorn; } location @unicorn { proxy_pass http://unicorn; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $host; proxy_redirect off; } } My config/routes.rb is pretty much empty: Advertise::Application.routes.draw do |map| resources :users end The index.html file is located in public/index.html and it loads fine if I request it directly: http://example.com/index.html To reiterate, when I remove all references to unicorn from the nginx conf, index.html loads without any problems, I have a hard time understanding why this occurs because nginx should be trying to load that file on its own by default. -- Here is the error stack from production.log: Started GET "/" for 68.107.80.21 at 2010-08-08 12:06:29 -0700 Processing by HomeController#index as HTML Completed in 1ms ActionView::MissingTemplate (Missing template home/index with {:handlers=>[:erb, :rjs, :builder, :rhtml, :rxml, :haml], :formats=>[:html], :locale=>[:en, :en]} in view paths "/www/example.com/releases/20100808170224/app/views", "/www/example.com/releases/20100808170224/vendor/plugins/paperclip/app/views", "/www/example.com/releases/20100808170224/vendor/plugins/haml/app/views"): /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/paths.rb:14:in `find' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/lookup_context.rb:79:in `find' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/base.rb:186:in `find_template' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/render/rendering.rb:45:in `_determine_template' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/render/rendering.rb:23:in `render' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/haml-3.0.15/lib/haml/helpers/action_view_mods.rb:13:in `render_with_haml' etc... -- nginx error log for this virtualhost comes up empty: 2010/08/08 12:40:22 [info] 3118#0: *1 client 68.107.80.21 closed keepalive connection My guess is unicorn is intercepting the request to index.html before nginx gets to process it.

    Read the article

  • Linux Teamviewer functionality, but for ssh only

    - by Icapan
    I need to access some Linux server behind NAT (no ports forwarded), so I need to have something like "phone home" like Teamviewer has. There is no GUI, but somebody can log in through SSH and dictate a password if it is changing (like Teamviewer). SSH (port 22) is enough (I can tunnel ports through SSH if I need). Any suggestions? How safe is it?

    Read the article

  • Ineractive logon message doesn't show?

    - by user19049
    We set the Group Policy for our Domain and OUs to show the logon message: Computer Configuration\Windows Settings\Security Settings\Local Policies\Security Options\ Interactive logon: Message text for users attempting to log on but nothing happen when the client computer logon. I checked the RSOP.MSC to see the group policy that set and the message is set on client computer but it doesn't show at the logon prompt. so what should I do? We have Windows server 2003 AD and Windows XP Pro on client computer.

    Read the article

  • Webserver logs: "Morfeus F***ing Scanner"

    - by Patrick
    I've just found these accesses in my web server log files: ::ffff:218.38.136.38 109.72.95.175 - [10/Jan/2011:02:54:12 +0100] "GET /user/soapCaller.bs HTTP/1.1" 404 345 "-" "Morfeus Fucking Scanner" ::ffff:218.38.136.38 109.72.95.174 - [10/Jan/2011:02:54:12 +0100] "GET /user/soapCaller.bs HTTP/1.1" 404 345 "-" "Morfeus Fucking Scanner" Should I start to worry ? Or is it just a normal attempt to hack my server ? thanks

    Read the article

  • Why apcupsd won't see the UPS connected to the USB posrt on FreeBSD 8.0 amd64

    - by Max Kosyakov
    Hello, Recently I installed an apcusbd on a FreeBSD 8.0 amd64 box via ports system. It installed perfectly but it won't run. Here what is says in the log: FATAL ERROR in generic-usb.c at line 636 Cannot find UPS device It appeared that HID driver picked the /dev/ugen4.2 which could cause the apcusb being unable to find the device. After I had discovered this, I rebuilt the kernel and removed the hid driver. Now it just shows "ugen4.2: <Tripp Lite> at usbus4" and no uhid0 device appears. Nevertheless the problem persisted. I tried to leave the DEVICE config setting blank --- won't help. Then I specified the particular device in the config, but it did not help either. Below you is the output of several commands that can provide some useful information on my case. server# /usr/local/etc/rc.d/apcupsd start Starting apcupsd. server# tail /var/log/messages | grep apcupsd Jun 17 22:30:00 server apcupsd[1520]: apcupsd FATAL ERROR in generic-usb.c at line 636 Cannot find UPS device -- For a link to detailed USB trouble shooting information, please see . Jun 17 22:30:00 server apcupsd[1520]: apcupsd error shutdown completed server# cat /usr/local/etc/apcupsd/apcupsd.conf ## apcupsd.conf v1.1 ## UPSCABLE usb UPSTYPE usb DEVICE /dev/ugen4.2 LOCKFILE /var/lock UPSCLASS standalone UPSMODE disable server# dmesg | grep '^u' uhci0: port 0xa800-0xa81f irq 16 at device 26.0 on pci0 uhci0: [ITHREAD] uhci0: LegSup = 0x0f00 usbus0: on uhci0 uhci1: port 0xa880-0xa89f irq 21 at device 26.1 on pci0 uhci1: [ITHREAD] uhci1: LegSup = 0x0f00 usbus1: on uhci1 uhci2: port 0xac00-0xac1f irq 18 at device 26.2 on pci0 uhci2: [ITHREAD] uhci2: LegSup = 0x0f00 usbus2: on uhci2 usbus3: EHCI version 1.0 usbus3: on ehci0 uhci3: port 0xa080-0xa09f irq 23 at device 29.0 on pci0 uhci3: [ITHREAD] uhci3: LegSup = 0x0f00 usbus4: on uhci3 uhci4: port 0xa400-0xa41f irq 19 at device 29.1 on pci0 uhci4: [ITHREAD] uhci4: LegSup = 0x0f00 usbus5: on uhci4 uhci5: port 0xa480-0xa49f irq 18 at device 29.2 on pci0 uhci5: [ITHREAD] uhci5: LegSup = 0x0f00 usbus6: on uhci5 usbus7: EHCI version 1.0 usbus7: on ehci1 uart0: port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: [FILTER] usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 usbus4: 12Mbps Full Speed USB v1.0 usbus5: 12Mbps Full Speed USB v1.0 usbus6: 12Mbps Full Speed USB v1.0 usbus7: 480Mbps High Speed USB v2.0 ugen0.1: at usbus0 uhub0: on usbus0 ugen1.1: at usbus1 uhub1: on usbus1 ugen2.1: at usbus2 uhub2: on usbus2 ugen3.1: at usbus3 uhub3: on usbus3 ugen4.1: at usbus4 uhub4: on usbus4 ugen5.1: at usbus5 uhub5: on usbus5 ugen6.1: at usbus6 uhub6: on usbus6 ugen7.1: at usbus7 uhub7: on usbus7 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered uhub4: 2 ports with 2 removable, self powered uhub5: 2 ports with 2 removable, self powered uhub6: 2 ports with 2 removable, self powered uhub3: 6 ports with 6 removable, self powered uhub7: 6 ports with 6 removable, self powered ugen4.2: at usbus4 server#

    Read the article

  • How can I get rid of specific error messages in the mac terminal?

    - by Julian Weimer
    For some reasons i always get the following whenever i log into my terminal: : command not found : command not found : command not found : command not found : command not found It's really a minor problem because everything is working fine, or at least everything what im using in the terminal. Still it would just look nicer without them. Any help? I'm running Mac OS 10.5.8 <= if this helps solving the problem

    Read the article

  • Compiling PHP with GD crashes with EXC_BREAKPOINT (SIGTRAP) on PPC Mac

    - by Ömer
    First of all, I should say that I have searched the whole Internet for this problem but I couldn't find any solution yet. I have a Mac mini PowerPC (PPC) and I run Apache webserver (httpd-2.2.22) with PHP (5.4.0) and I do all the configure & compilation jobs by myself. If configure with: './configure' '--prefix=/usr/local/php5' '--mandir=/usr/share/man' '--infodir=/usr/share/info' '--sysconfdir=/etc' '--with-config-file-path=/etc' '--with-zlib' '--with-zlib-dir=/usr' '--with-openssl=/usr' '--without-iconv' '--enable-exif' '--enable-ftp' '--enable-mbstring' '--enable-mbregex' '--enable-sockets' '--with-mysql=/usr/local/mysql' '--with-pdo-mysql=/usr/local/mysql' '--with-mysqli=/usr/local/mysql/bin/mysql_config' '--with-apxs2=/usr/local/apache2/bin/apxs' '--with-mcrypt' then the PHP works flawlessly. But if I add the GD module by adding these to the script above: '--with-gd' '--with-jpeg-dir=/usr/local/lib' '--with-freetype-dir=/usr/X11R6' '--with-png-dir=/usr/X11R6' '--with-xpm-dir=/usr/X11R6' the PHP gets configured and compiled without any errors but it causes EXC_BREAKPOINT (SIGTRAP) (see the Crash Reporter log below) when I request a page which calls PHP module. It's obvious that something related to the GD module is causing this, probably FreeType module because it's present in the log but it may not be definite of course. When the PHP crashes (or more accurately, httpd) the CPU goes 100% for 10 to 15 seconds until it recovers. I need to use the GD module and keep the Mac mini PowerPC. So, what should I do to solve this problem? Process: httpd [79852] Path: /usr/local/apache2/bin/httpd Identifier: httpd Version: ??? (???) Code Type: PPC (Native) Parent Process: httpd [79846] Date/Time: 2013-11-04 15:44:28.444 +0200 OS Version: Mac OS X 10.5.8 (9L31a) Report Version: 6 Anonymous UUID: 0178B7F8-2241-43F7-A651-9E7234D41A37 Exception Type: EXC_BREAKPOINT (SIGTRAP) Exception Codes: 0x0000000000000001, 0x0000000093c11e0c Crashed Thread: 0 Application Specific Information: *** single-threaded process forked *** Thread 0 Crashed: 0 com.apple.CoreFoundation 0x93c11e0c __CFRunLoopFindMode + 328 1 com.apple.CoreFoundation 0x93c13d88 CFRunLoopAddSource + 276 2 com.apple.DiskArbitration 0x901a6e8c DAApprovalSessionScheduleWithRunLoop + 52 3 ...ple.CoreServices.CarbonCore 0x9512e67c _FSGetDiskArbSession(__DASession**, __DAApprovalSession**) + 540 4 ...ple.CoreServices.CarbonCore 0x9512e420 CreateDiskArbDiskForMountPath(char const*) + 84 5 ...ple.CoreServices.CarbonCore 0x9512d2c8 FSCacheableClient_GetVolumeCachedInfo(char const*, statfs const*, CachedVolumeInfo*, __DADisk*, __DADisk**) + 280 6 ...ple.CoreServices.CarbonCore 0x9512cca4 MountVolume(char const*, statfs*, unsigned char, unsigned char, __DADisk*, short*) + 352 7 ...ple.CoreServices.CarbonCore 0x9512ca48 MountInitialVolumes() + 172 8 ...ple.CoreServices.CarbonCore 0x9512c4d4 INIT_FileManager() + 164 9 ...ple.CoreServices.CarbonCore 0x9512c390 GetRetainedVolFSVCBByVolumeID(unsigned long) + 48 10 ...ple.CoreServices.CarbonCore 0x9512adf4 PathGetObjectInfo(char const*, unsigned long, unsigned long, VolumeInfo**, unsigned long*, unsigned long*, char*, unsigned long*, unsigned char*) + 184 11 ...ple.CoreServices.CarbonCore 0x9512acc4 FSPathMakeRefInternal(unsigned char const*, unsigned long, unsigned long, FSRef*, unsigned char*) + 64 12 libfreetype.6.dylib 0x0070a0fc FT_New_Face_From_Resource + 56 13 libfreetype.6.dylib 0x0070a3b0 FT_New_Face + 48 14 libphp5.so 0x0118d1a8 fontFetch + 824 15 libphp5.so 0x0118edac php_gd_gdCacheGet + 220 16 libphp5.so 0x0118d6d8 php_gd_gdImageStringFTEx + 360 17 libphp5.so 0x011763c0 php_imagettftext_common + 1504 18 libphp5.so 0x01176494 zif_imagefttext + 20 19 libphp5.so 0x014b9c68 zend_do_fcall_common_helper_SPEC + 1048 20 libphp5.so 0x01452898 _ZEND_DO_FCALL_SPEC_CONST_HANDLER + 440 21 libphp5.so 0x014ba878 execute + 776 22 libphp5.so 0x013f190c zend_execute_scripts + 316 23 libphp5.so 0x013779f4 php_execute_script + 596 24 libphp5.so 0x014bbe64 php_handler + 1972 25 httpd 0x000020c0 ap_run_handler + 96 26 httpd 0x00006ae0 ap_invoke_handler + 224 27 httpd 0x000305c4 ap_process_request + 116 28 httpd 0x0002c768 ap_process_http_connection + 104 29 httpd 0x00012d30 ap_run_process_connection + 96 30 httpd 0x00012ecc ap_process_connection + 92 31 httpd 0x000373e4 child_main + 1220 32 httpd 0x000376a8 make_child + 296 33 httpd 0x000377e4 startup_children + 100 34 httpd 0x000387d4 ap_mpm_run + 3988 35 httpd 0x0000a320 main + 3280 36 httpd 0x000019c0 start + 64

    Read the article

  • AutoRestart error in SQL Server logs (reason: Access is denied)

    - by Michael Teper
    My instance of SQL Server 2008 SP1 crashed, which is a separate issue, and I see the following set of messages in the SQL Server Agent log: [139] AutoRestart: Attempting to restart the MSSQLSERVER service (attempt #1)... [368] AutoRestart: Unable to restart the MSSQLSERVER service (reason: Access is denied) Is there an authoritative place that describes what permissions should be assigned to a domain account that the SQL Server Agent runs as? Thank you!

    Read the article

  • ApacheTop and Plesk

    - by Tomccaul
    Hi, I am trying to find a way to monitor my apache server so I can see which domain is causing slow down on my server when they occur. I was hoping I would be able to do it with ApacheTop but I have to list our each log file separately as Plesk splits domains apache logs into individual files. Is there a way I can do this with ApacheTop or should I be using another tool? Thanks

    Read the article

  • Dovecot Virtual Users Not Authenticating

    - by blankabout
    We have a standard Postfix/Dovecot installation working perfectly with real users but cannot work out how to add virtual users, all virtual user login attempts fail with authentication errors. Following are snippets from the configuration files: /etc/postfix/main.cf: virtual_mailbox_domains = virtualexample.com virtual_mailbox_base = /var/spool/vhosts virtual_mailbox_recipients = hash:/etc/postfix/virtual_mailbox_recipients /etc/dovecot/dovecot.conf: !include conf.d/*.conf /etc/dovecot/conf.d/10-auth.conf auth_mechanisms = cram-md5 digest-md5 plain passdb { driver = passwd-file # Path for passwd-file. Also set the default password scheme. args = scheme=cram-md5 /etc/cram-md5.pwd } /etc/cram-md5.pwd [email protected]{MD5}$1$uIMvzy92$9Xt67B/qw4u6txkkxzne80 This is a snippet from the log when a login attempt is made: auth: Debug: Loading modules from directory: /usr/lib64/dovecot/auth auth: Debug: Module loaded: /usr/lib64/dovecot/auth/libauthdb_ldap.so auth: Debug: Module loaded: /usr/lib64/dovecot/auth/libdriver_sqlite.so auth: Debug: Module loaded: /usr/lib64/dovecot/auth/libmech_gssapi.so auth: Debug: passwd-file /etc/cram-md5.pwd: Read 1 users auth: Debug: auth client connected (pid=21990) auth: Debug: client in: AUTH#0111#011CRAM-MD5#011service=imap#011lip=1.1.1.1#011rip=2.2.2.2#011lport=143#011rport=51774 auth: Debug: client out: CONT#0111#011PDI1Njc0NjQ1NzQ3MTY0NTkuMTM0MTIxNzkwN0BncDM+ auth: Debug: client in: CONT auth: Debug: passwd-file([email protected],2.2.2.2): lookup: [email protected] file=/etc/cram-md5.pwd auth: Debug: client out: OK#0111#[email protected] auth: Debug: master in: REQUEST#0111630404609#01121990#0111#011b66b5f46b520a08e1d19d3d249be7073 auth: Debug: passwd([email protected],2.2.2.2): lookup auth: passwd([email protected],2.2.2.2): unknown user auth: Error: userdb([email protected],2.2.2.2): user not found from userdb passwd auth: Debug: master out: NOTFOUND#0111630404609 imap: Error: Authenticated user not found from userdb, auth lookup id=1630404609 (client-pid=21990 client-id=1) imap-login: Internal login failure (pid=21990 id=1) (auth failed, 1 attempts): user=, method=CRAM-MD5, rip=2.2.2.2, lip=1.1.1.1, mpid=21993 auth: Debug: auth client connected (pid=22010) auth: Debug: client in: AUTH#0111#011CRAM-MD5#011service=imap#011lip=1.1.1.1#011rip=2.2.2.2#011lport=143#011rport=51775 auth: Debug: client out: CONT#0111#011PDcxMDkwNDY1NTQzODUzMDkuMTM0MTIxNzkyOEBncDM+ auth: Debug: client in: CONT auth: Debug: passwd-file([email protected],2.2.2.2): lookup: [email protected] file=/etc/cram-md5.pwd auth: Debug: client out: OK#0111#[email protected] auth: Debug: master in: REQUEST#011343539713#01122010#0111#011e47b1345784e2845d59e794afa9a6bbe auth: Debug: passwd([email protected],2.2.2.2): lookup auth: passwd([email protected],2.2.2.2): unknown user auth: Error: userdb([email protected],2.2.2.2): user not found from userdb passwd auth: Debug: master out: NOTFOUND#011343539713 imap: Error: Authenticated user not found from userdb, auth lookup id=343539713 (client-pid=22010 client-id=1) imap-login: Internal login failure (pid=22010 id=1) (auth failed, 1 attempts): user=, method=CRAM-MD5, rip=2.2.2.2, lip=1.1.1.1, mpid=22011 It would appear that the user lookup is not working, even tho' the log suggests that Dovecot is using the /etc/cram-md5.pwd file and the user is configured in that same file. There are of course dozens of examples of using virtual users with Dovecot, but all the ones we have found either refer to Dovecot 1.x (we are using 2.x), using only virtual users (we must use real AND virtual users) or want to use a MySQL db, we need to use a text file. Some hints about where we are going wrong would be very much appreciated.

    Read the article

  • help with sendmail configuration to send mail through my gmail account??

    - by pradeepa
    This is the sendmail.ini file what to change now # Example for a user configuration file # Set default values for all following accounts. defaults logfile "\xampp\sendmail\sendmail.log" # Mercury account Mercury host localhost from postmaster@localhost auth off # A freemail service example account gmail tls on tls_certcheck off host smtp.gmail.com from ****@gmail.com auth on user ****@gmail.com password ******* # Set a default account account default : Mercury

    Read the article

  • How does Kerberos work with SSH?

    - by Phil
    Suppose I have four computers, Laptop, Server1, Server2, Kerberos server: I log in using PuTTY or SSH from L to S1, giving my username / password From S1 I then SSH to S2. No password is needed as Kerberos authenticates me Describe all the important SSH and KRB5 protocol exchanges: "L sends username to S1", "K sends ... to S1" etc. (This question is intended to be community-edited; please improve it for the non-expert reader.)

    Read the article

  • Stoping EXIM on ubuntu

    - by justintime
    I have EXIM running on a server taht I am trying to decommision (but I still have stuff I need to move off). $ sudo /etc/init.d/exim4 stop * Stopping MTA [ OK ] * ALERT: exim paniclog /var/log/exim4/paniclog has non-zero size, mail system possibly broken 2011-02-01 19:18:37 string too large in smtp_notquit_exit() How can I stop exim from running, and accepting mail on port 25.

    Read the article

< Previous Page | 398 399 400 401 402 403 404 405 406 407 408 409  | Next Page >