Search Results

Search found 23783 results on 952 pages for 'edit and continue'.

Page 403/952 | < Previous Page | 399 400 401 402 403 404 405 406 407 408 409 410  | Next Page >

• Can a USB/IDE/SATA adapter be flaky?

  - by Ward

  I use USB/IDE/SATA converters a lot and on the two that I have now, I sometimes get errors copying files to drives. It only happens when I'm copying big files to the drive (big can mean as little as 100MB, I think it happens more often with bigger files - 300MB or more), and basically the copy will fail and I'll get one or more error messages about "Delayed write failed." But if I disconnect the drive and re-connect it, I'll usually be able to continue. (The file that was being copied will be corrupt, but otherwise the drive is fine.) I just noticed a new type of flakiness: the data transfer rate can vary widely. I copied one set of files (5x300MB files) and it took 10+minutes, then I copied another set (approx. the same sizes) and it took less than a minute. I haven't done systematic testing, the other things I'm doing on my laptop at the same time might have some impact, and I haven't cross-checked the two adapters I have and the 3 hard drives I'm working with to see if there's a pattern. I'm more wondering if anyone else has seen anything like this.

  Read the article

• WNDR3700 Router + Cisco SG200-08 + LACP + Dual Uplink

  - by kobaltz

  Background I have a storage server that has several virtual machine images stored on them. I would store them locally, but I have limited space on my desktop (using SSD storage). I would like to increase the bandwidth between the desktop and the storage server by using two NICs on each computer. My original configuration allowed about 55MBps between the desktop and storage server. This storage server also has several TBs of documents, pictures, movies, vms, and ISO/programs. The storage server has 8 1.5TB hard drives in a RAID 10 configuration with a hardware RAID controller. The benchmarks on the RAID 10 are about 300MBps. Configuration In short, I am trying to bridge my switch and router. The switch is a small 8 port Cisco smart switch that supports 802.3ad LACP. I have two computers plugged into the switch, each with 2 Intel Gigabit NICs. The first computer is a Windows 7 machine that has the Intel ANS software installed. I have LACP configured with the computer and now show 3 NICs (2 Physical + 1 TEAM Virtual @ 2Gbps). It looks like this computer is configured correctly. I trunked the two ports that this computer is plugged into with the switch's web interface. The second computer is a homebrew storage box running debian. I also have the bonding enabled on this machine and the switch configured with LACP. Without having the WNDR3700 router in the picture yet, I am able to communicate between the Windows 7 machine and the debian box since they both have static IP addresses. With LACP enabled on both machines I am getting about 106-108MBps speeds. Issue I plug in a network cable from the switch into the router and enable DHCP on the desktop. I saw no need to have a static address on the desktop. My transfer rates are still from 106MBps-108MBps. While this is still a boost, I am trying to figure out how to get about 140-180MBps. I am thinking that I need to increase the bandwidth from the router to the switch. My switch allows 4 groups for port trunking. I plugged in a second network cable from the router to the switch. My question is, what is the proper way to fix this issue. Should I port trunk the two ports that are going from the switch to the router? Keep in mind that the router is a WNDR3700 and is unsure whether or not it supports LACP. I do have OpenWRT installed on the router, but it still wasn't clear in any documentation that I found if it supported 802.3ad LACP standards. I am also wondering if there needs to be anything changed within the Cisco settings. [Edit] - Corrected some numbers, wasn't really paying attention. It looks like the speeds though at least two NICs are bonded with LACP is still reaching the max bandwidth of one port. Is there a way to configure the switch so that I can increase this bandwidth? Also, on the storage server, I had a couple of extra NICs laying around and threw them on there as well. Another EDIT and More Findings I happened to look at the traffic of each individual NIC and think that I see the problem. I tested with a simple transfer for a 4GB file. I noticed that only one of the NICs was taking the load of the traffic. I then copied the file back to the Storage Server and noticed that the other NIC was sending out the traffic. I have 802.3ad LACP enabled on the two NICs and I see that it gets enabled dynamically on the switch's interface. Should I be using Static Link Aggregation?

  Read the article

• Windows 7 disk errors after a few hours of runtime

  - by GFK

  I'm having trouble understanding what is going on with my work PC. Whenever I boot it, it runs fine for a while, then starts to randomly show disk errors. The displayed error often contains the message "not enough storage is available to process this command", although depending on the application that fails it can be different. This has happened for weeks now and is getting worse. This is what troubles me: It never seems to impact critical parts of the system (no BSOD, no freeze). Only some applications seem impacted, refusing to function correctly after a while: Outlook 2010 cannot download RSS feeds anymore, Firefox 6 or IE9 cannot download anything bigger than 3MB without failing, Windows Update fails, all msi installers fail, Visual Studio 2010 starts failing in weird manners... It only happens after a while using it (typically 3 hours, but it seems that installing a program or compiling several times makes it shorter) Rebooting solves it (temporarily). The system: The OS is Windows 7 Pro Spanish SP1, 32 bits The system is an HP Compaq 6000 Pro with 4 GB memory (only 3.4GB usable since the system is 32bit), one 500GB hard drive. Installed applications include: Visual Studio 2010, SQL Server 2008 R2, VMWare Workstation 7, Microsoft Security Essentials, Office 2010. Shutting down all related services and processes doesn't seem to change anything. The diagnostics I've run so far: Hard drive : 465GB, 165GB free Process Explorer : physical and virtual memory seem ok (pagefile is 5.3GB, physical memory usage 70%, system commit 39%) Windows Memory diagnostic tool: OK CHKDSK returned: 488282111 KB total disk space. 281668248 KB in 265779 files. 150188 KB in 62949 indexes. 0 KB in bad sectors. 571755 KB in use by the system. The log file has occupied 65536 kilobytes. 205891920 KB available on disk. For non-spanish speakers, that means all ok. SMART diagnostic tools (DiskCheckup) report all values normal. temperatures are in the normal range (HWinfo). The event viewer doesn't seem to contain any significant message. ran CCleaner 3, without any noticeable effect. I was thinking about some file number limit (between Visual Studio projects and other applications, there are around 300.000 files on the hard drive), but I couldn't find any. It's possible there is something related with the use of the temporary folders (it's the only explanation I have for why applications fail but Windows doesn't), but I cannot confirm that. Only thing I cannot find out is if chkdsk reporting 65MB for the log is normal. It seems since Vista it always reports this. Any other cleaning/diagnostic tool you might know of? Edit: I ran several other tools since I first published the question: Seagate SeaTools (the HD manufacturer's analysis tool): complete test run OK. Intel Rapid 10.1 (the HD controller manufacturer's troubleshooting tool): the HD's ok. Microsoft Desktop Heap Monitor: Desktop Heap Information Monitor Tool (Version 8.1.2925.0) Copyright (c) Microsoft Corporation. All rights reserved. Session ID: 1 Total Desktop: ( 46464 KB - 11 desktops) WinStation\Desktop Heap Size(KB) Used Rate(%) WinSta0\Winlogon (s1) 128 3.6 WinSta0\Disconnect (s1) 64 3.8 WinSta0\Default (s1) 20480 3.0 msswindowstation\mssrestricteddesk (s0) 1024 0.2 __X78B95_89_IW__A8D9S1_42_ID (s0) 1024 0.2 Service-0x0-3e5$\Default (s0) 1024 0.6 Service-0x0-3e4$\Default (s0) 1024 0.3 Service-0x0-3e7$\Default (s0) 1024 2.1 WinSta0\Winlogon (s0) 128 1.9 WinSta0\Disconnect (s0) 64 3.8 WinSta0\Default (s0) 20480 0.0 All ok, desktop heap usage < 5% Edit 2: I tried totally resetting my account by creating a new one, logging under this new one and delete the first one (local rights and files), then logging back with this deleted account (it is a domain account). No luck. Also, I found out often the error is "not enough storage is available to process this command". Searching on the internet, I found an old troubleshooting tip (setting a registry key to raise the IRP stack limit, whatever it is) which did not change anything.

  Read the article

• PHP application failed to connect after a network plugged back in

  - by tntu

  My data-center appears to have had some issues with their network and thus my server has suffered from on an off network connectivity for about an hour. After the connection has been completely re-established my code still kept reporting the same issue over and over until I have restarted the service. The code is a simple PHP code that loops forever checking the Apple feed-back server and then sleeps for a few minutes and then it begins all over again. Now I understand the error being generated if the network is down but once it got back up why did it continue until I have restarted the code? Does PHP have something that needs to be re-initialized or something?? Messges log: Dec 20 08:57:22 server kernel: r8169: eth0: link down Dec 20 08:57:28 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:29 server kernel: r8169: eth0: link down Dec 20 08:57:33 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:33 server kernel: r8169: eth0: link down Dec 20 08:57:37 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:38 server kernel: r8169: eth0: link down Dec 20 08:57:44 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:44 server kernel: r8169: eth0: link down Dec 20 08:57:52 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:52 server kernel: r8169: eth0: link down Dec 20 09:10:58 server kernel: r8169 0000:06:00.0: eth0: link up PHP Error: PHP Warning: stream_socket_client(): php_network_getaddresses: getaddrinfo failed: Name or service not known in /home/push/feedback.php on line 36 Code Line 36: $apns = stream_socket_client('ssl://feedback.sandbox.push.apple.com:2196', $errcode, $errstr, 60, STREAM_CLIENT_CONNECT, $stream_context);

  Read the article

• Apache + Tomcat: Which one should handle SSL? IP-based proxy forwarding?

  - by delirial

  We currently have a Tomcat application running with SSL on port 443. Right now we have an apache server that accepts http requests on port 80 and redirects to the Tomcat instance: <VirtualHost *:80> ServerName domain.com ServerAlias domain.com <LocationMatch "/"> Redirect permanent / https://domain.com/ </LocationMatch> </VirtualHost> Tomcat is handling SSL, because there's no proxy, just a simple redirect to the SSL port: <Connector port="443" maxThreads="200" scheme="https" secure="true" SSLEnabled="true" keystoreFile="/app/ssl/domain_com.jks" keystorePass="ourpassword" clientAuth="false" sslProtocol="TLS"/> We want to begin using the apache web server as a proxy and additionally, do per-IP redirects to certain apps that should only be used by hosts on a pre-determined IP range. We would also like to redirect IPs that don't match the pre-determined list to a static html page hosted on the apache server. My first question is: Should I continue to handle SSL on Tomcat's end, or should I use apache with SSL while forwarding to an "unprotected" tomcat port? Is there any way to redirect to different apps (and potentially hosts) depending on the incoming IP? thanks, del

  Read the article

• Why is ssh agent forwarding not working?

  - by J. Pablo Fernández

  In my own computer, running MacOSX, I have this in ~/.ssh/config Host * ForwardAgent yes Host b1 ForwardAgent yes b1 is a virtual machine running Ubuntu 12.04. I ssh to it like this: ssh pupeno@b1 and I get logged in without being asked for a password because I already copied my public key. Due to forwarding, I should be able to ssh to pupeno@b1 from b1 and it should work, without asking me for a password, but it doesn't. It asks me for a password. What am I missing? This is the verbose output of the second ssh: pupeno@b1:~$ ssh -v pupeno@b1 OpenSSH_5.9p1 Debian-5ubuntu1, OpenSSL 1.0.1 14 Mar 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug1: Connecting to b1 [127.0.1.1] port 22. debug1: Connection established. debug1: identity file /home/pupeno/.ssh/id_rsa type -1 debug1: identity file /home/pupeno/.ssh/id_rsa-cert type -1 debug1: identity file /home/pupeno/.ssh/id_dsa type -1 debug1: identity file /home/pupeno/.ssh/id_dsa-cert type -1 debug1: identity file /home/pupeno/.ssh/id_ecdsa type -1 debug1: identity file /home/pupeno/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.9p1 Debian-5ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9p1 Debian-5ubuntu1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: sending SSH2_MSG_KEX_ECDH_INIT debug1: expecting SSH2_MSG_KEX_ECDH_REPLY debug1: Server host key: ECDSA 35:c0:7f:24:43:06:df:a0:bc:a7:34:4b:da:ff:66:eb debug1: Host 'b1' is known and matches the ECDSA host key. debug1: Found key in /home/pupeno/.ssh/known_hosts:1 debug1: ssh_ecdsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password debug1: Next authentication method: publickey debug1: Trying private key: /home/pupeno/.ssh/id_rsa debug1: Trying private key: /home/pupeno/.ssh/id_dsa debug1: Trying private key: /home/pupeno/.ssh/id_ecdsa debug1: Next authentication method: password pupeno@b1's password:

  Read the article

• Force delivery retry without restarting the SMTP Service on Windows Server 2008 R2

  - by Mathias R. Jessen

  I have a Windows Server 2008 R2 box hosting 3 virtual SMTP servers; vSMTP01, vSMTP02 and vSMTP03. The first two are configured to deliver all messages to dedicated smarthosts, while the last is set to just deliver the messages on its own. All other delivery settings are as default ----(vSMTP01)-----> {SMARTHST01} / ----Inbound mail--->---SMTPSRV01---[----(vSMTP02)-----> {SMARTHST02} \ ----(vSMTP03)-----> { Internet } Now I want to take SMARTHST01 out for maintenance, but I don't want to reject submissions to vSMTP01 while doing so, so I just let it continue running. When SMARTHST01 is no longer responding, vSMTP01 queues the messages and wait for the first retry interval to pass (15 minutes). So far so good. Let's say SMARTHST01 gets online again after 20 minutes. The first interval has passed, and I'll have to wait another 25 minutes for the second retry interval to pass. If I stop and start the SMTP Service (Services.msc - Simple Mail Transfer Protocol service - Stop), the server will retry all deliveries, but that would cause a service interruption for ALL virtual SMTP servers on the machine, which is highly undesirable. How can I manually force vSMTP01 to retry delivery of all queued messages without interrupting the service of vSMTP02 and vSMTP03?

  Read the article

• How can I stop SipVicious ('friendly-scanner') from flooding my SIP server?

  - by a1kmm

  I run an SIP server which listens on UDP port 5060, and needs to accept authenticated requests from the public Internet. The problem is that occasionally it gets picked up by people scanning for SIP servers to exploit, who then sit there all day trying to brute force the server. I use credentials that are long enough that this attack will never feasibly work, but it is annoying because it uses up a lot of bandwidth. I have tried setting up fail2ban to read the Asterisk log and ban IPs that do this with iptables, which stops Asterisk from seeing the incoming SIP REGISTER attempts after 10 failed attempts (which happens in well under a second at the rate of attacks I'm seeing). However, SipVicious derived scripts do not immediately stop sending after getting an ICMP Destination Host Unreachable - they keep hammering the connection with packets. The time until they stop is configurable, but unfortunately it seems that the attackers doing these types of brute force attacks generally set the timeout to be very high (attacks continue at a high rate for hours after fail2ban has stopped them from getting any SIP response back once they have seen initial confirmation of an SIP server). Is there a way to make it stop sending packets at my connection?

  Read the article

• Unable to resize ec2 ebs root volume

  - by nathanjosiah

  I have followed many of the tutorials that pretty much all say the same thing which is basically: Stop the instance Detach the volume Create a snapshot of the volume Create a bigger volume from the snapshot Attach the new volume to the instance Start the instance back up Run resize2fs /dev/xxx However, step 7 is where the problems start happening. In any case running resize2fs always tells me that it is already xxxxx blocks big and does nothing, even with -f passed. So I start to continue with tutorials which all basically say the same thing and that is: Delete all partitons Recreate them back to what they were except with the bigger sizes Reboot the instance and run resize2fs (I have tried these steps both from the live instance and by attaching the volume to another instance and running the commands there) The main problem is that the instance won't start back up again and the system error log provided in the AWS console doesn't provide any errors. (it does however stop at the grub bootloader which to me indicates that it doesn't like the partitions(yes, the boot flag was toggled on the partition with no affect)) The other thing that happens regardless of what changes I make to the partitions is that the instance that the volume is attached to says that the partition has an invalid magic number and the super-block is corrupt. However, if I make no changes and reattach the volume, the instance runs without a problem. Can anybody shed some light on what I could be doing wrong? Edit On my new volume of 20GB with the 6GB image,df -h says: Filesystem Size Used Avail Use% Mounted on /dev/xvde1 5.8G 877M 4.7G 16% / tmpfs 836M 0 836M 0% /dev/shm And fdisk -l /dev/xvde says: Disk /dev/xvde: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x7d833f39 Device Boot Start End Blocks Id System /dev/xvde1 1 766 6144000 83 Linux Partition 1 does not end on cylinder boundary. /dev/xvde2 766 784 146432 82 Linux swap / Solaris Partition 2 does not end on cylinder boundary. Also, sudo resize2fs /dev/xvde1 says: resize2fs 1.41.12 (17-May-2010) The filesystem is already 1536000 blocks long. Nothing to do!

  Read the article

• Can't access shared folder of win8/win7 machine - Error code: 0x80004005. Unspecified Error

  - by ruslan

  It's ironic that I, software engineer with 12 years of experience, continue to have this problem from one version of Windows to another without being able to achive consistent result (sometimes it works). Here it goes again. I have a machine with Win8 Consumer Preview. It doesn't really matter that it's win8. I had same issue with win7 before. On given machine I created local admin user with same name and password I have on second PC (the machine I'm typing this from now). I have two questions to you guys. Why I'm not able to access C$ share of win8 machine from another Win7 machine? I get error that C$ doesn't exist even though it does. Why I'm not able to access share named "test" in Win8 for which Permission set to Full for Everyone. When I attempt to access it from Win7 machine I'm asked to enter username and password. After entering administrator credentials I get error "Windows cannot access \192.168.1.123\test. Error code: 0x80004005. Unspecified Error". Windows Firewall is disabled on Win8 machine for both Private and Public networks. Guest account is disabled. Built-in admin account is enabled. Machine is pingable from other machines.

  Read the article

• computer freezes but music continues

  - by Danny

  Recently I have had a problem where my computer will freeze completely but if I happen to be streaming Pandora in a tab that will continue playing. If I wait about 2-5 minutes it will eventually come back and start working normally. I also noticed that during the period that it is unresponsive that the HDD activity light stays lit the whole time, not flashing. I've ran memtest86+ and a diagnostic from Western Digital for my HDD model and none of them reported any errors. The specs for my computer are 1 x ASRock H55M/USB3 R2.0 LGA 1156 Intel H55 HDMI USB 3.0 Micro ATX Intel Motherboard 1 x CORSAIR Enthusiast Series CMPSU-550VX 550W ATX12V V2.2 SLI Ready CrossFire Ready 80 PLUS Certified Active PFC Compatible with Core i7 Power Supply 1 x Intel Core i3-540 Clarkdale 3.06GHz LGA 1156 73W Dual-Core Desktop Processor Intel HD Graphics BX80616I3540 1 x G.SKILL 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Dual Channel Kit Desktop Memory Model F3-12800CL9D-4GBNQ 1 x ASUS PCE-N13 PCI Express 150/300Mbps Transfer/Receive Rate Wireless Adapter 1 x EVGA 01G-P3-1556-KR GeForce GTX 550 Ti (Fermi) FPB 1GB 192-bit GDDR5 PCI Express 2.0 x16 HDCP Ready SLI Support Video Card I can't imagine what would be causing these problems.

  Read the article

• Using the full width of an Excel chart with two Y-axes

  - by Jørn Schou-Rode

  I am trying to create a line chart in MicrosoftExcel 2007 with two data series, each with their own Y-axis. First, I create a simple chart by selecting the two data series, and choosing Insert > Charts > Line from the Ribbon. I now see the following chart in my workbook: I then continue my quest by right clicking one of the data series (lines) and choosing Format data series > Series Options > Secondary Axis. My chart is now looks like this: This is almost what I want. I did not expect to see the gap between the last X-axis tick point (x = 5) and the secondary (right most) Y-axis. Why does Excel introduce this gap? Is there anything I can do to avoid it? I have tried right clicking the X-axis and seleting Format Axis > Axis Options > Position Axis: Between tick marks, but that only introduces a similar gap on by the primary (left most) Y-axis.

  Read the article

• lenovo x1 carbon windows 8 frequent wifi disconnect issue

  - by hIpPy

  I'm having frequent wifi disconnects on my Lenovo X1 Carbon Touch laptop. I got this laptop 2 months back and it has been happening ever since about 3-5 times a day and 10 times a week on average. I've Frontier Fios internet. Power connected or not does not matter. Once I get disconnected, I try below to connect again in that order: turn Airplane mode on and off, troubleshoot network problems windows troubleshooter), restart the laptop I'd find that the WiFi adapter would get disabled and sometimes windows troubleshooting would help but more than often I'd end up restarting the laptop. A week back, I upgraded my wifi network adapter drivers (now Intel, version 15.5.6.48, 10/3/2012). I still get disconnected frequently but turning Airplane mode on and off gets me connected again. So the driver update did help. Windows 8 is updated. None of the other devices (nexus, iphone phones, nexus7, ipad tablets) would have wifi issues when my laptop would get disconnected. config: Intel(R) Centrino(R) Advanced-N 6205 (WiFi network adapter) Microsoft Windows 8 Pro Microsoft Windows [Version 6.2.9200] x64-based PC LENOVO System Model: 3443CTO X1 Carbon Touch I recently noticed this log message When I got disconnected in event viewer: Your computer was not assigned an address from the network (by the DHCP Server) for the Network Card with network address 0x[XXXXXXXXXXXX]. The following error occurred: 0x79. Your computer will continue to try and obtain an address on its own from the network address (DHCP) server. Any idea?

  Read the article

• backup an existing linux server to a virtualbox virtual machine

  - by user146526

  I have some servers and VPSs to many companies across the world. I want to back them up locally. I have some backup solutions enabled to remote hosts, but I want to have a local backup on a computer at home. What I am thinking is: 1) Create a virtualbox virtual machine, install the same version linux as the server. 2) Use rsync to backup the server to the local virtualbox machine. (something like rsync -av --delete --progress --exclude '/dev/' --exclude '/proc/' root@server_ip:// / ) 3) Repeat the command every few days update files. 4) In case of a hard disk failure, or any other bad event, reverse the rsync command and get the files back and continue my bussiness. I tried it with 2 openvz VPS, the one was a backup of the other. I also tried to transfer normal linux server host to openvz machine and it worked great. That way looks pretty clean and easy to me, this is the kind of solution I am looking for. However I need to be sure that this will work if I am going to do it. The question is, will that work ok ? Does anyone see any problem with that ? Do you have any other suggestions ? Thanks

  Read the article

• Windows 7 is stuck at "Starting Windows" when I attempt to boot computer

  - by Eli

  Basically, whenever I turn on my computer, it gets to the Starting Windows phase and just stays there. The startup animation still plays, yet it gets nowhere. I have tried booting into safe mode, however it gets stuck at loading CLASSPNP.SYS. It then freezes there and doesn't continue booting. I have tried booting into recovery mode from the hard drive, and it freezes after displaying the background image. I have tried booting from a recovery CD, which works, and I was able to use system restore. However, using system restore did not fix it, and it still is stuck at the Starting Windows screen. I have tried booting a Windows CD (Windows 8 Retail Installer) to see if I could upgrade it to fix this issue, however that froze at a blank screen after it got past the boot logo. I have tried changing around the BIOS settings (including resetting), to no avail. I have tried re-plugging the internal PSU cables (this is a custom-built desktop), yet this has changed nothing. I can boot into a loopback Ubuntu install on the same drive, which works fine, other than the fact that it has issues with some of the USB ports and the network card. This system has worked fine for the past few months, completely stable, and nothing in the configuration has changed before this error started happening. Startup Repair on the Windows recovery CD doesn't find any issues. Unplugging my secondary hard drive or swapping around memory doesn't change anything. The hard drive itself is fine, it hasn't shown any signs of failure and once again, boots my other OS fine. If anyone could help with this, that would be great. I can't seem to find any possible solution to this. If it makes any difference, my system specs are as follows: AMD FX-8320 Gigabyte GA-970A-D3 4GB of DDR3 Radeon HD 6870 550w PSU I'd like to not have to reinstall Windows, for I have more than a terabyte of data that I would have to back up if that becomes the only option. EDIT: I have since tried the following: Tried the solution involving restoring files from RegBackup, which changed nothing. Tried testing everything with Hiren's boot CD, everything comes back as fine. Tried disabling everything unnecessary in the BIOS and unplugging everything unneeded, it still hangs. Tried swapping out every possible combination of RAM, it still has the same result. The RAM is not at fault it seems Tried every GPU I own (which is many!) and it still hangs at the exact same place. Tried minimizing the power consumption as much as possible, even using an old PCI graphics card. It still hangs at the same place in the same way, signifying that it's not the PSU at fault. Tried resetting the BIOS again, still nothing. Tried every possible combination of BIOS options, even downclocking everything, it still hangs in the same spot. Tried upgrading the BIOS from version FB to FD, which changed nothing. Based on this, I would conclude the motherboard to be at fault. Are there any other possibilities? I don't want to spend $150 for a new motherboard. EDIT 2: This is what it gets stuck at when I try to boot into safe mode: Note the slight graphical corruption at the top of the screen. No matter how I set up the system, this seems to be there. In addition, either it has stopped booting into safe mode now, or it takes upwards of 2+ hours, and I haven't left it running for that long.

  Read the article

• ddwrt client brigde acces point lost

  - by llazzaro

  Ok I have an AP with ddwrt firm (i know its not the best, but continue reading!) AP is configured to work like a wifi "transparent" brigde, also it had a virtual wifi network card to expand radius of wifi signal in that same AP. The brigde is working, computers behind AP gets ips from main routers which shares internet....BUT! I cant access webgui of the bridge AP... Main problem : AP is lost, but its working as brigde. I cant find it in the network (it didnt have any ip!) so I cant change any configuration... First solution : Reset AP, but it cannot be done. Reset button dont works due to a bug in ddwrt micro firm that mi linksys WAP54g had installed (I really hate this firmware I like more openwrt that my main router has) Second Solution : arp -a from main router , from computers behind AP...It dont appears in the list. Any more ideas, the router at some level must be there, the brigde is working. I know its possible that the AP is with an ip like 192.168.100.2 , my subnect actually is 172.16.X.X. :) thanks!

  Read the article

• How to configure a Web.Config file to allow custom 404 handling while still displaying on-page 500 error detail?

  - by Mark

  To customize 404 handling and based on the hosting company's suggestion, we are currently using the following web.config setup. However, we quickly realized that with this configuration, any page error (500 error) are also getting redirected to this custom error page. How can I modify this config file so we can continue to handle 404 with custom file while still able to view on-page error? <?xml version="1.0" encoding="utf-8" ?> <configuration> <system.webServer> <httpErrors errorMode="DetailedLocalOnly" defaultPath="/Custom404.html" defaultResponseMode="ExecuteURL"> <remove statusCode="404" subStatusCode="-1" /> <error statusCode="404" prefixLanguageFilePath="" path="/Custom404.html" responseMode="ExecuteURL" /> </httpErrors> </system.webServer> <system.web> <customErrors mode="On"> <error statusCode="404" redirect="/Custom404.html" /> </customErrors> </system.web> </configuration>

  Read the article

• WINDOWS: Your computer hangs. You can windows + R (run dialog) but performance is so halted taskMGR

  - by John Sullivan

  The question is, what process are available to try to recover from total system instability before pulling the plug when we can do nothing but programs or batches in the path from the run dialog (windows + r key), and performance is so dead that taskMGR / procEXP / other programs with visual guis are not usable? I am not a windows expert, but ideally someone out there has written a program that does more or less stuff like this: Immediately set (or perhaps I can set from the run prompt) its priority to extremely high, evaluate performance bottlenecks. E.g. is CPU 100%? If so identify offending program(s) or problems. Attempt / log fixes, then provide crude feedback asking the user if his performance has stabilized enough to abort, wait a few seconds, if no feedback continue, etc. etc. Eventually try to do any "system cleanup" if the program decides it cannot recover and perhaps finally provide a series of beeps to the user, or what have you, to say "OK, I give up, time to pull the plug". Ideally create a log, when able. These kinds of horrible hangs are a situation where surely trying something, anything, is better than nothing -- as long as that something is intelligent -- when the alternative is ripping out the power coord. Again, I am not a windows expert, so perhaps there is a much more elegant "hands on" approach I am not aware of.

  Read the article

• How to force the start and end date of a task in Microsoft Project to be on the same day?

  - by Hauke P.

  I have a task called "Interview person A about topic X". The task's duration is set to 2 hours. The start date of the task should automatically be calculated taking dependencies and resource availabilities into account. My question boils down to: How can I force this task to start and end on the same date? Background: In my case, Microsoft Project sets the start date to a Friday at 5pm. As my working hours are set to 8am to 12am and 1pm to 6pm (Mon-Fri), Microsoft Project "splits up" the task at 6pm on Friday and plans to continue it at 8am on the following Monday. However, it does not make any sense to stop the interview on a Friday and restart it on Monday. Therefore the automatic suggestion is not helpful in this case. That's why I'm looking for a way way to force the task to start and end on the very same day. (In my example, I'd like Microsoft Project to delay the start date of the task until Monday 8am as this is the first time slot in which the task "fits in completely".) By the way: I have lots of such cases... for that reason it would be really great if there was a solution that doesn't just deal with this single special case.

  Read the article

• Find which files an apache process is writing to?

  - by Haluk

  We have this apache process which becomes io-bound time to time. Using atop, we can see it is a write operation. Using lsof -p <PID> we can see a list of files open by the httpd process. First we thought "log" files must be the problem. So we turned them off just to test. However write operations still continues. We will continue testing a few other things. For instance we use php session variables a lot. Maybe php session files are getting all the writing. But is there a way to quickly identify files which get written to by the httpd process? This way we can focus our efforts on those files. UPDATE: We used the strace command as suggested. Here are two lines from the output. write(23, "\27\0\0\0\3SET CHARACTER SET utf8", 27) = 27 write(23, "\17\0\0\0\3SET NAMES utf8", 19) = 19 We do not have a mysql process on this server. So is strace also showing what is being written to an ethernet port? UPDATE2: During high io load, the process which consumes most of the write resources gives the following output to strace -e trace=write -p <PID>: --- SIGCHLD (Child exited) @ 0 (0) --- write(9, "!", 1) = 1 write(19, "OPTIONS * HTTP/1.0\r\nUser-Agent: Apache (internal dummy connection)\r\n\r\n", 70) = 70 However I cannot figure out where these are being written to.

  Read the article

• VMware guest pauses when the host is idle - how do I keep it running?

  - by EMP

  I'm running VMWare Worstation 7 with Windows 7 x64 as guest, Windows XP x64 as host. Inside the guest I run a long-running console application, which prints out progress messages with timestamps on them. Sometimes I leave it running for several hours while I lock the host OS and don't touch the computer at all. When I come back I find that some time after I left it seems to have paused and automatically resumed: the console app hasn't made much progress and there's a large time gap in its progress messages. There's nothing relevant in the host event log, but in the guest Application event log I can see these messages around the time I left: A request to disable the Desktop Window Manager was made by process (VMware Tools Service) The Desktop Window Manager was unable to start because composition was disabled by a running application And later, around the time I returned, this shows up in the System log: The system time has changed to ?2012?-?01?-?12T06:36:46.921000000Z from ?2012?-?01?-?12T03:18:19.953079000Z. That seems to support my theory that it's VMware doing something and not Windows itself. The question is: how do I stop it doing that? I want my application to continue running. By the way, the power options are set to never sleep in both guest and host.

  Read the article

• NGINX returning 404 error on a valid url

  - by Harrison

  We have a site that runs PHP-FPM and NGINX. The application sends invitations to site members that are keyed with 40 character random strings (alphanumerics only -- example below). Today for the first time we ran into an issue with this approach. The following url: http://oursite.com/notices/response/approve/1960/OzH0pedV3rJhefFlMezDuoOQSomlUVdhJUliAhjS is returning a 404 error. This url format has been working for 6 months now without an issue, and other urls following this exact format continue to resolve properly. We have a very basic config with a simple redirect to a front controller, and everything else has been running fine for a while now. Also, if we change the last character from an "S" to anything other than a lower-case "s", no 404 error and the site handles the request properly, so I'm wondering if there's some security module that might see something wrong with this specific string... Not sure if that makes any sense. We are not sure where to look to find out what specifically is causing the issue, so any direction would be greatly appreciated. Thanks! Update: Adding a slash to the end of the url allowed it to be handled properly... Would still like to get to the bottom of the issue though. Solved: The problem was caused by part of my configuration... Realized I should have posted, but was headed out of town and didn't have a chance. Any url that ended in say "css" or "js" and not necessarily preceded by a dot (so, for example, http://site.com/response/somerandomestringcss ) was interpreted as a request for a file and the request was not routed through the front controller. The problem was my regex for disabling logging and setting expiration headers on jpgs, gifs, icos, etc. I replaced this: location ~* ^.+(jpg|jpeg|gif|css|png|js|ico)$ { with this: location ~* \.(jpg|jpeg|gif|css|png|js|ico)$ { And now urls ending in css, js, png, etc, are properly routed through the front controller. Hopefully that helps someone else out.

  Read the article

• How to write rules for persistent net names?

  - by ndemou

  I know that a process generates persistent network card names based on rules found in /lib/udev/rules.d/75-persistent-net-generator.rules. I also know how to completely disable this process with a simple echo '#' > /etc/udev/rules.d/75-persistent-net-generator.rules but I've read that I "could also write my own rules file to give the interface a name — the persistent rules generator ignores the interface if a name has already been set" (/etc/udev/rules.d/README confirms that this is possible). Do you have any pointers to documentation about how to write such rules? (I mostly care about Debian/Ubuntu and a bit less for CentOS) As a specific example of why I want to write custom rules: I have two identical servers with one onboard LAN and one PCI LAN. In case of HW failure I want to be able to move disks from HW#1 to HW#2 and it's important for eth0 to continue pointing to the onboard card and eth1 to the PCI card (no one wants to mess with cabling in the middle of a HW failure panic). My current workaround works but is a lot of work[1] so I wonder if writing custom rules would allow me to express something simple like this: cards with MAC A or B should be named eth0 cards with MAC C or D should be named eth1 follow default naming scheme for anything else [1] install the OS in HW#1 and keep a copy of /etc/udev/rules.d/70-persistent-net.rules. Move the disks to HW#2 and keep a second copy of the same file. Concatenate the two copies and manually edit the NAME="ethX" part. Replace /etc/udev/rules.d/70-persistent-net.rules with my version. Finally disable auto-creation of a new 70-persistent-net.rules using echo '#' > /etc/udev/rules.d/75-persistent-net-generator.rules

  Read the article

• How to perform this Windows 7 permissions change on many files via GUI or command line

  - by hippietrail

  After using my external hard drive on another Windows 7 computer to tweak photos with Windows Live Photo Gallery then upload them to Facebook I found the modified images were now not visible on the original Windows 7 computer. I'm not sure if the things I tried to get it working subsequently changed anything, but I do know this is the sequence of actions that makes the permissions of the modified files match those of the unmodified files: Right click on broken image file, select "Properties" On the "Security" tab press the "Advanced" button In the "Permissions" tab press the "Continue" button with the shield icon on it Tick the box marked "Include inheritable permissions from this object's parent Click the "Remove" button to remove the only current entry "Type: Allow, Name: Administrators (XYZ\Administrators), Permission: Full control, Inherited From: OK on the "Permissions" tab. OK on the "Security" tab. Now this same procedure does not work at the folder level. It results in "access denied" dialogs. I'm looking for some way to perform this exact modification on all the images I edited on the other computer. I'm happy to use the Windows GUI in Explorer or any other included tools. I'm happy to use the Windows command line. I'd prefer not to use a third-party tool since I'd have to be satisfied it's not doing anything else. I'm not looking for a different way to change permissions to other settings to make an external drive full of photos editable on multiple computers. At least not in this question.

  Read the article

• Vista: window focus problem

  - by GateKiller

  Sorry for the vague title but this one is hard to explain so bear with me please. I'm using Windows Vista at work for web development and sometimes when I Click or Alt-Tab to background window, the window will get focus but it will not be brought to the front. In order to bring the window to the front, I have to click on the applications border (when the resize cursor appears) and the window will then jump to the front. I've had this problem for about a year now and it happens at least a dozen times a day, but it doesn't do this all the time - seems random. I hope I have explained the issue fully (and you've understood it) and would appreciate any constructive answers or comments to solve this problem. Example: If I Alt-Tab from Google Chrome to Notepad and this problem randomly occurs, Google Chrome will remain in front of Notepad, however, I will be able to type text into Notepad while the window is behind Google Chrome. Clicking on Notepad's content area will not bring it to the front but clicking it's window border will. Video Exampe http://vimeo.com/19388998 In this video, I clicked from Google Chome to UltraEdit and chrome stayed in font, but as you can see, I can still type in UltraEdit. I'm starting to believe that this could be a bug in Google Chrome so I'll continue to watch if this between other applications.

  Read the article

< Previous Page | 399 400 401 402 403 404 405 406 407 408 409 410  | Next Page >