Search Results

Search found 11483 results on 460 pages for 'ip contracts'.

Page 403/460 | < Previous Page | 399 400 401 402 403 404 405 406 407 408 409 410  | Next Page >

  • VLAN Through Switch Doesn't Work

    - by vcsjones
    I have the following scenario: I have a Cisco Aironet 1040 access point. I have it configured with two SSIDs, each going to a different VLAN. So: SSID internal : VLAN 90 SSID guest : VLAN 70 On the router side, I have a Cisco RV220W (with the radios now turned off) and have setup VLANs with like VLAN IDs. VLAN 90 : 192.168.90.0/24 VLAN 70 : 192.168.70.0/24 As far as DHCP is concerned, each VLAN has a "DHCP Server" in the router's configuration: So with the access point connected directly to the router, everything works great. I connect to the internal network, and I get a 192.168.90.x address, and the guest network gets a 70.xxx address. Next I introduced a Cisco SG200-50 PoE switch between the router and the access point. The port is configured as a trunk port, so the VLAN tags should go right through the switch back to the router. However, when something is connected to the access point, nothing works. It isn't able to get an IP address, and manually assigning one doesn't seem to let any traffic route. Given that the access point works correctly when connected to the router directly, I believe the switch is misconfigured. What am I missing here? What can I use to better diagnose what the problem might be? It's small business equipment, so CLI access is not available. Below are screenshots of the switch's config. The access point is connected to GE2.

    Read the article

  • Unable to Connect to just Google Servers

    - by Akshat Mittal
    I am in an extremely strange problem. I am unable to connect to just Google Servers. I am not able to access any site related to Google, Google.com | YouTube | Google+ | Webmaster Tools | jQuery CDN, nothing is working. I am able to open any other website (as I am posting this question on SuperUser), even the Google DNS (8.8.8.8 and 8.8.4.4) are offline. Please Help!! Update 1: Google DNS are back online, YouTube is back online. But website on domain google.com is not working (ex: play.google.com, maps.google.com, google.com/search, etc). Update 2: I am able to access Google.com (only) with (one of) its IP addresss(s) listed below: 74.125.227.41 74.125.227.46 74.125.227.32 74.125.227.33 74.125.227.34 74.125.227.35 74.125.227.36 74.125.227.37 74.125.227.38 74.125.227.39 74.125.227.40 Update 3: I consulted my friends nearby and they said that they are also experiencing the same problem. Seams like this is a major problem in this area (or India !!) The Problem is Now Solved!! I am able to open Google.com

    Read the article

  • File uploads and client_max_body_size in nginx + gunicorn + django

    - by carlosescri
    I need to configure nginx + gunicorn to be able to upload files greater than the default max size in both servers. My nginx .conf file looks like this: server { # ... location / { proxy_pass_header Server; proxy_set_header Host $http_host; proxy_redirect off; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Scheme $scheme; proxy_connect_timeout 60; proxy_pass http://localhost:8000/; } } The idea is to allow requests of 20M for two locations: /admin/path/to/upload?param=value /installer/other/path/to/upload?param=value I've tried to add location directives at the same level than the one I've pasted here (getting 404 errors) and also tried to add them inside the location / directive (getting 413 Entity Too Large errors). My location directives look like these in their simplest form: location /admin/path/to/upload/ { client_max_body_size 20M; } location /installer/other/path/to/upload/ { client_max_body_size 20M; } But they don't work (actually I tested lots of combinations and I'm desperate thinking about this. Please, help If you can: What settings do I need to set to make this work? Thank you so much!

    Read the article

  • Squid3 not caching simple request and response

    - by Nick Spacek
    Hi folks, I've pared down my squid.conf to try to figure this out: http_port 80 accel defaultsite=host.to.cache cache_peer ip.to.cache parent 80 0 no-query originserver acl our_sites dstdomain host.to.cache http_access allow our_sites refresh_pattern . 1 20% 4320 Requests are being proxied correctly, so that's a start. Here's a request: GET http://host.to.cache/path?some_param=true Accept: */* Accept-Charset: ISO-8859-1,utf-8 Accept-Encoding: gzip,deflate,sdch Accept-Language: en-US,en Connection: keep-alive Host: host.to.cache User-Agent: myuseragent And the response: Connection: keep-alive Content-Length: 585 Content-Type: application/xml Date: Thu, 06 Jan 2011 18:33:11 GMT Via: 1.0 localhost (squid/3.0.STABLE19) X-Cache: MISS from localhost X-Cache-Lookup: MISS from localhost:80 The response has no caching-related headers, but I thought that refresh_pattern would set a default behavior for responses without caching-related headers. For my test, I wanted to cache everything for one minute at minimum. Am I missing something obvious? I did take a peek at this question: Squid isn't caching ...and ran through the page here: http://www.mnot.net/cache_docs/ briefly, but didn't see anything relevant (not to say that there isn't, I could have missed something). Thanks for any help.

    Read the article

  • Dynamic DNS Updates with Wireless and Wired interfaces

    - by Phaedrus
    We have offices full of Windows & Mac users who obtain IP addresses from a Windows DHCP server, which in turn updates Dynamic DNS entries. We are noticing major inconsistencies with the entries, and have found that the problem is occurring more on Macs than on windows, and even more when users are frequently switching from wired to wireless adapter, which makes sense, as this sequence occurs: User enables wired adapter and registers Proper DNS User enables wireless adapter and registers 2nd proper DNS entry user switches off wireless manually and 2nd entry remains improperly until scavenge. Our help desk folks rely heavily (maybe more than they should) on the dynamic entries as part of their business process. For example, the user submits a help desk ticket, and the staff member expects to be able to remote desktop to their machine by hostname, which is hyperlinked in the helpdesk ticketing app. We have implemented multiple solutions & band-aids to different symptoms of the problems such as: Using DNS Reservations for Macintosh PCs Using DNS Scavenging to remove old records Switching from a Cisco DHCP server to the Windows DHCP Server But no matter what we do, it seems impossible to maintain perfect records. Has anyone encountered this problem before? What is industry best practice? Comments & Suggestions are much appreciated, /P

    Read the article

  • Bad Mumble control channel performance in KVM guest

    - by aef
    I'm running a Mumble server (Murmur) on a Debian Wheezy Beta 4 KVM guest which runs on a Debian Wheezy Beta 4 KVM hypervisor. The guest machines are attached to a bridge device on the hypervisor system through Virtio network interfaces. The Hypervisor is attached to a 100Mbit/s uplink and does IP-routing between the guest machines and the remaining Internet. In this setup we're experiencing a clearly recognizable lag between double-clicking a channel in the client and the channel joining action happening. This happens with a lot of different clients between 1.2.3 and 1.2.4 on Linux and Windows systems. Voice quality and latency seems to be completely unaffected by this. Most of the times the client's information dialog states a 16ms latency for both the voice and control channel. The deviation for the control channels mostly is a lot higher than the one of the voice channels. In some situations the control channel is displayed with a 100ms ping and about 1000 deviation. It seems the TCP performance is a problem here. We had no problems on an earlier setup which was in principle quite like the new one. We used Debian Lenny based Xen hypervisor and a soft-virtualised guest machine instead and an earlier version of the Mumble 1.2.3 series. The current murmurd --version says: 1.2.3-349-g315b5f5-2.1

    Read the article

  • How do I secure Sql Server 2008 R2

    - by Mark Tait
    I have both a dedicated and a VPS (from Fasthosts) virtual server - the web sites/applications I run on these, access Sql Server stored on the same web server. Until now, I have logged onto Sql Server on both the deidicated and VPS server, from Sql Server Management Studio - until I noticed in my server application logs, multiple attempts to logon to Sql Server using the 'sa' username, but failed password. So someone/bot is trying hard (repeatedly every couple of hours, for approx 20 attempts during each instance) to log on... so obviously I have to lock down access to Sql Sever remotely. What I have done is gone into Configuration Manager, and in Sql Server Network Configuration - Protocols for Sql2008 and also in Sql Native Client 10.0 Configuration - Client Protocols - I have diabled Named Pipes, TCP/IP (and VIA by default). I have left Shared Memory enabled. I also disabled in Sql Server Services, the Sql Server Browser. Now the only way I can manage the databases on these servers, is by logging on to them via Remote Desktop. Can anyone confirm if this is the correct way of stopping anyone maliciously logging on to Sql Server? (I'm not a DBA or security expert - and there are hundreds of articles advising all different ways - but I was hoping for the experts here to confirm, or otherwise, if what I've done is correct) Thank you, Mark

    Read the article

  • BIND returns serverfail when querying for its authoriative domain

    - by estol
    Hi there Serverfault folks! First of all: sorry about the title, I had some problem coming up with the proper title. I have a little home server set up, for internet sharing, samba, basic http, dlna mediaserver and what not, and I happend to have a domain at hand, so I thought why not direct it to this computer? I have a BIND 9.8.0 installed, and - afaik - configured it properly. For a few days, the public view did not worked, and I really did not cared, since the local view worked. But now suddenly, even the local view fails. If I try to query the nameserver for anything in my domain, it returns the following error: $ nslookup andromeda.dafaces.com ;; Got SERVFAIL reply from ::1, trying next server ;; Got SERVFAIL reply from ::1, trying next server Server: 127.0.0.1 Address: 127.0.0.1#53 ** server can't find andromeda.dafaces.com.dafaces.com: SERVFAIL Also, the public view points to the old ip address of the domain, probably because of the same error. Some information about the system: $ uname -a Linux tressis 2.6.37-ARCH #1 SMP PREEMPT Tue Mar 15 09:21:17 CET 2011 x86_64 AMD Athlon(tm) 64 X2 Dual Core Processor 5000+ AuthenticAMD GNU/Linux $ named -v BIND 9.8.0 And the named.conf file: # cat /etc/named.conf // // /etc/named.conf // include "/etc/rndc.key"; #controls { # inet 127.0.0.1 allow {localhost; } keys { "dnskulcs"; }; #}; options { directory "/var/named"; pid-file "/var/run/named/named.pid"; auth-nxdomain yes; datasize default; // Uncomment these to enable IPv6 connections support // IPv4 will still work: listen-on-v6 { any; }; listen-on { any; }; // Add this for no IPv4: // listen-on { none; }; // Default security settings. // allow-recursion { 127.0.0.1; ::1; 192.168.1.0/24; }; // allow-recursion { any; }; allow-query { any; }; allow-transfer { 127.0.0.1; ::1; 92.243.14.172; 87.98.164.164; 88.191.64.64; }; allow-update { key "dnskulcs"; }; version none; hostname none; server-id none; zone-statistics yes; forwarders { 213.46.246.53; 213.26.246.54; 8.8.8.8; 8.8.4.4; 192.188.242.65; 193.227.196.3; 2001:470:20::2; }; }; view "local" { match-clients { 192.168.1.0/24; 127.0.0.1; ::1; fec0:0:0:ffff::/64; }; recursion yes; zone "localhost" IN { type master; file "localhost.zone"; allow-transfer { any; }; }; zone "0.0.127.in-addr.arpa" IN { type master; file "127.0.0.zone"; allow-transfer { any; }; }; zone "." IN { type hint; file "root.hint"; }; zone "dafaces.com" IN { type master; file "internal/dafaces.com.fw"; allow-update { key "dnskulcs"; }; }; zone "1.168.192.in-addr.arpa" IN { type master; file "internal/dafaces.com.rev"; allow-update { key "dnskulcs"; }; }; }; view "public" { match-clients { any;}; recursion no; zone "dafaces.com" IN { type master; file "external/dafaces.com.fw"; allow-transfer { 87.98.164.164; 195.234.42.1; 88.191.64.64; }; }; }; //zone "example.org" IN { // type slave; // file "example.zone"; // masters { // 192.168.1.100; // }; // allow-query { any; }; // allow-transfer { any; }; //}; logging { channel xfer-log { file "/var/log/named.log"; print-category yes; print-severity yes; print-time yes; severity info; }; category xfer-in { xfer-log; }; category xfer-out { xfer-log; }; category notify { xfer-log; }; }; All help would be highly appreciated! EDIT: Zone files: # cat /var/named/internal/dafaces.com.fw $ORIGIN . $TTL 3600 ; 1 hour dafaces.com IN SOA tressis.dafaces.com. postmaster.dafaces.com. ( 2011032201 ; serial 28800 ; refresh (8 hours) 7200 ; retry (2 hours) 2419200 ; expire (4 weeks) 3600 ; minimum (1 hour) ) NS tressis.dafaces.com. A 192.168.1.1 MX 10 mail.dafaces.com. $ORIGIN _tcp.dafaces.com. _http SRV 0 5 80 www.dafaces.com. _ssh SRV 0 5 22 tressis.dafaces.com. $ORIGIN dafaces.com. acrisius A 192.168.1.230 andromeda A 192.168.1.7 andromeda-win7 CNAME andromeda aspasia A 192.168.1.233 athena A 192.168.1.232 callisto A 192.168.1.102 db A 192.168.1.1 management A 192.168.1.1 ; web management for the router functions haley A 192.168.1.5 hoth A 192.168.1.101 mail A 192.168.1.1 satelite A 192.168.1.20 sony-player A 192.168.1.103 TXT "310f16de2d2712dfc4ae6e5c54f60f828e" torrent A 192.168.1.1 tracker A 192.168.1.1 tressis A 192.168.1.1 www A 192.168.1.1 zeus A 192.168.1.231 and # cat /var/named/external/dafaces.com.fw $ORIGIN . $TTL 3600 dafaces.com IN SOA ns.dafaces.com. postmaster.dafaces.com. ( 2011032405; serial 28800; refresh 7200; retry 2419200; expire 3600; minimum ) NS ns.dafaces.com. NS ns0.xname.org. NS ns1.xname.org. NS ns2.xname.org. A 89.135.129.37 MX 10 mail.dafaces.com. $ORIGIN dafaces.com. ;Szolgaltatasok _ssh._tcp SRV 0 5 22 tressis _http._tcp SRV 0 5 80 www ns A 89.135.129.37 hoth A 89.135.129.37 www A 89.135.129.37 mail A 89.135.129.37 db A 89.135.129.37 torrent A 89.135.129.37 tracker A 89.135.129.37 Edit: Ohh, hell I almost forgot. Since the node is connected to the internet via a residential connection, there is a possibility, that the public ipv4 address will change(but thank god, it is a very rare case), so I daily update the external IP address in the zone file with a shellscript: # cat /etc/cron.daily/dnsupdate #!/bin/sh FILE="/var/named/external/dafaces.com.fw" SERIAL=$(date +%Y%m%d05) PUBLIC_IP=$(ifconfig internet |sed -n "/inet addr:.*255.255.255.255/{s/.*inet addr://; s/ .*//; p}") cat $FILE | sed --posix 's/^.* serial$/\t\t\t\t\t'$SERIAL'; serial/' | sed --posix 's/[0-9]*\.[0-9]*\.[0-9]*\.[0-9]*/'$PUBLIC_IP'/' > /tmp/ujzona mv /tmp/ujzona $FILE /etc/rc.d/named reload

    Read the article

  • virtualbox instances dedicated-server with custom dnsmasq

    - by ovanes
    I have dedicated server where I planned to run virtualbox virtual machines. Since the VMs are managed with vagrant/chef I may end up with many different ones. I thought it would be a great idea to deploy a dnsmasq on the server, which is going to dynamically assign the ip addresses to the VMs. Since each Vagrant/Chef recipe is configured to set the VM's host name I can find/reference the appropriate VM by the host name. Finally, the entire infrastructure is not directly accessible via internet, so the dedicated Server is the OpenVPN host. So the entire infrastructure may be seen as: +-------------------------------------+ | Dedicated Server | | | | +-------------+ +------------+ | +------------------+ | | DNSMasq | | OpenVPN |<==========>| Client | | +-------------+ +------------+ | | | | ^ ^ | +------------------+ | | | | | +--+ | | | | +-------+ | | | | VM1 | | | | +-------+ | | | ... | | | +-------+ | | +-| VM2 | | | +-------+ | +-------------------------------------+ Now some questions which I am struggling with: Are there any other suggestions to access private infrastructure, because I don't want to reinvent the wheel. On the Dedicated Server I don't see the vboxnet0 interface but VirtualBox is installed without GUI. Accessing of virtual boxes via ssh works fine. Did I miss smth? DNSMasq must serve the local VMs only, otherwise there is a chance that local DNSMasq start to serve other server's on the network, what I don't want. Because I don't see vboxnet0 I tend to use no-dhcp-interface=eth0 config option. Are there any thoughts on that despite, the fact that a second NW-card (which is not the case), might start serving DHCP-Requests? How should I config the VM's network interface that I am able to access it via OpenVPN and resolve the hostnames using the DNSMasq. I think it should be the host-only network card. Should I do bridging in the OpenVPN config or is it sufficient to use routing.

    Read the article

  • Juniper SSG 5 VPN

    - by Ethabelle
    I have a host who set up our Juniper SSG 5 VPN with Firmware version-6.2.0r5.0 I've been trying to set up VPN on it using this guide: http://kb.juniper.net/InfoCenter/index?page=content&id=KB4094 I've followed the steps and on my Mac, whenever I try to connect using L2TP over IPSec I get the following error; Summary of Steps: Create User (give them L2TP auth ability), Create Group, Place User in Group, Create VPN Gateway, Create VPN, create IP Pool, change default L2TP settings, create Untrust Trust Policy. The L2TP-VPN server did not respond. Try reconnecting. If the problem continues, verify your settings and contact your Administrator. I looked in my Firewall's logs, but I don't even see anything under Reports Logs Events. I'm.. obviously missing something, I just don't know what I'm missing at this point. I'm just starting networking and this is sort of Step 101 and I'm getting annoyed and just want to throw up OpenVPN, but I've read that has problems with Juniper Firewalls. Hooray.

    Read the article

  • AWS VPC ELB vs. Custom Load Balancing

    - by CP510
    So I'm wondering if this is a good idea. I have a Amazon AWS VPC setup with a public and private subnets. So I all ready get the Internet Gateway and NAT. I was going to setup all my web servers (Apache2 isntances) and DB servers in the private subnet and use a Load Balancer/Reverse Proxy to pick up requests and send them into the private subnets cluster of servers. My question then, is Amazons ELB's a good use for these, or is it better to setup my own custom instance to handle the public requests and run them through the NAT using nginx or pound? I like the second option just for the sake of having a instance I can log into and check. As well as taking advantage of caching and fail2ban ddos prevention, as well as possibly using fail safes to redirect traffic. But I have no experience with their ELB's, so I thought I'd ask your opinions. Also, if you guys have an opinion on this as well, would using the second option allow me to only have 1 public IP address and be able to route SSH connections through port numbers to respective instances? Thanks in advance!

    Read the article

  • Windows Firewall Software to Filter Transit Traffic

    - by soonts
    I need to test my networking code for Nintendo Wii under the conditions when some specific Internet server is not available. Wii is connected to my PC with crossover ethernet cable. PC has 2 NICs. PC is connected to hardware router with ethernet cable. The hardware router serves as NAT and has an internet connected to its uplink. I set the Wii to be in the same lan as PC by using Windows XP Network bridge. I can observe the WII network traffic using e.g. Wireshark sniffer. Is there a software firewall that can selectively filter out transit traffic? (e.g. block outgoing TCP connections to 123.45.67.89 to port 443) I tried Outpost Pro 2009 and Comodo. Outpost firewall blocks all transit traffic with it's implicit "block transit packet" rule. If the transit traffic is explicitly allowed by creating the system-wide low level rule, then it's allowed completely and no other filter can selectively block it. Comodo firewall only process rules when the packet has localhost's IP as either source or destination, allowing the rest of the traffic. Any ideas? Thanks in advance! P.S. Platform is Windows XP 32 bit, no other OSes is allowed, Windows ICS (Internet Connection Sharing) doesnt work since the Wii is unable to connect, becides I don't like the idea of adding one more level of NAT.

    Read the article

  • Windows : Map-a-network-drive to a remote Shared-Folder (on QNAP NAS) using OpenVPN

    - by spelltox
    Provided my lack of networking knowledge, I've been struggling with this issue for quite a few days now : I have a QNAP-TS212 NAS on which i've created a shared-folder (mostly excel files). All the computers in the local network (windows) are able to access it without any problem. Now, i want to access that shared-folder remotely (windows client), so : I enabled OpenVPN (and PPTP) in QNAP admin. Installed OpenVPN on the remote client. Applied the configuration file that the QNAP generated - Configuration (openvpn.ovpn) : client dev tun script-security 3 proto udp remote ***MY_WAN_IP*** 1194 resolv-retry infinite nobind ca ca.crt auth-user-pass reneg-sec 0 cipher AES-128-CBC comp-lzo OpenVPN connect successfully from the remote client. Now, here's my problem : I can ping the NAS (got IP 10.8.0.1) from the remote client, But when i try to map-a-network-drive, i don't see the shared folder or the NAS or any of the other computers in the network... I checked - all computers are in "WORKGROUP" workgroup. I'm probably missing some basic knowledge, So - any help would be greatly appreciated ! Many thanks.

    Read the article

  • VNC from Windows to OS X Lion: App stuck in fullscreen mode

    - by Jonny
    I'm connecting to a remote Mac through a Windows. ahh it gets more complicated than that. I'm sitting by my iMac. I use Virtual Box in it to launch Windows 7. In it I have a VPN connection to a remote Windows network, which allows me to use Remote Desktop to one of the Windows (Vista!) boxes over there. From that Vista box I VNC into a Mac OS X Lion. (Don't ask me why, but that Mac doesn't have a public ip which prevents me from accessing it in the first place.) So: OSXLion - (virtual)Windows7 - Windows Vista - OSX Lion That last Mac was recently upgraded from Snow Leopard. Now with Lion, sometimes apps run in fullscreen. Somehow I can't get out of that fullscreen. Normally you'd move the mouse pointer to the top of screen and a menu list bar drops down allowing you to reach the fullscreen button top right. Now, in my current setup that menu list bar never drops down on the remote Mac at the end of the line. Any ideas?

    Read the article

  • Nexus One WiFi connection problems.

    - by sunocky
    I have two new Nexus One for a research project. For the projects I need to keep a server running on the phone. But soon I found out that both the phones have inconsistent WiFi connection problems at my home. It can connect to my WiFi network, but will drop off in a random time. And in order to reconnect to my WiFi, I may need to reboot my router, or the phone will say "obtaining IP address" and then "Unsuccessful". I also own a G1 with firmware version 1.6, it has no such connection problems. Well, to my surprise, the two Nexus One works fine with connecting to the WiFi network at my work place, which is a WEP type WiFi connection. By the way, it is a WPA type connection at my home. Anyone knows what's the problems with the Nexus One? Any suggestions on what should I do if I want to keep the WiFi connection live all the time at my home? Thanks very much!

    Read the article

  • Connecting to my home router web interface from work

    - by Joe
    Hi, I'm trying to connect to my home router web interface from work. I use dyndns, because I don't have a static IP at home, and it works perfectly from any other place except my workplace (update: I made a mistake, see edit below). When trying to access the web interface from work I get a "500 Server Error" with the code: SERVER_RESPONSE_RESET. I'm not trying to use any protocols such as remote desktop, I'm only trying to access the web interface. I can access any other web page from my workplace with no problems, and I think my router web interface is like any other web page, isn't it? I thought maybe my work place proxy blocks addresses of services like dyndns, so I also applied another trick. Since I have a web page on my own domain (say www.mydomain.com) which I can access from work, I tried adding a CNAME to my domain which is linked to the dyndns address (router.mydomain.com). This way if anyone enters the address router.mydomain.com from anywhere, they reach my home router web interface, and there's no way of knowing it's a dyndns address (or is there?). However, it still doesn't work from my workplace (I get the same error message). Any ides? Edit: I'm sorry to say I made a mistake earlier. I used to be able to access my home router web interface from my old workplace, and I thought it was still possible since I don't recall making any configuration changes. However, after reading the replies, I went over to my old workplace and checked, and it doesn't work from there either. I'm very sorry for giving out wrong and misleading information about my problem. So to summarize: my problem is that I can't access my home router web interface from anywhere.

    Read the article

  • Connecting remotely to an SQL server inside a LAN

    - by vondip
    Hello everyone, I am using SQL server 2008 inside my home lan. I've configured it to accept remote connections and I can now connect to the server from other pcs inside the lan. The problems rises when I try connecting to the server from a computer outside of my home lan. I've disabled my router's firewall and I've configured a virtual server on port 1433 forwarding to the correct lan ip. What's wrong? why is it not working? Thank you very much for your help~! Edit: This is the error I keep getting: A network related or instance specific error occured while establishing connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that the SQL SERVER is configued to allow remote connections. (provider : Sql network interfaces, error: 25- Connection string is not valid) OK these are my router's details: edimax br-6204wg I am not sure how I am supposed to browse google.com. can you be a bit more specific?

    Read the article

  • Router startup problems

    - by gfmoz
    I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the power off and on again it all works. I also have to restart my PC too in order for everything to work. How can I solve this problem? Just leave the router turned on all time? I prefer a daily IP switch, though. May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

    Read the article

  • Router startup problems

    - by gfmoz
    I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the power off and on again it all works. I also have to restart my PC too in order for everything to work. How can I solve this problem? Just leave the router turned on all time? I prefer a daily IP switch, though. May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

    Read the article

  • Nginx and Gunicorn hanging on GET requests

    - by whatWhat
    I'm using Nginx + Gunicorn which is serving my Django project. All GET requests hang for ~1 min. The content seems to be available immediately as I can see it in the Browser inspector but the browser itself looks like it's still waiting for more data. Heres my Ngnix config #allow for up to 3 connections per second. limit_req_zone $binary_remote_addr zone=one:10m rate=3r/s; server { listen 80; server_name example.com; root /var/www/example.com/example/; # serve directly - analogous for static/staticfiles location /media/ { # this changes depending on your python version root /home/example/; } location /static/ { # if asset versioning is used if ($query_string) { expires max; } root /var/www/example.com; } location / { #Allow for a burst of 50. limit_req zone=one burst=50 nodelay; proxy_pass_header Server; proxy_set_header Host $http_host; proxy_redirect off; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Scheme $scheme; proxy_connect_timeout 10; proxy_read_timeout 10; proxy_pass http://localhost:8001/; } # what to serve if upstream is not available or crashes error_page 500 502 503 504 /media/50x.html; } My Gunicorn Config: bind = "127.0.0.1:8001" workers = 3 worker_class = "gevent" Is there anything obvious that would be causing the requests to stay open for so long?

    Read the article

  • Prevent nginx from redirecting traffic from https to http when used as a reverse proxy

    - by Chris Pratt
    Here's my abbreviated nginx vhost conf: upstream gunicorn { server 127.0.0.1:8080 fail_timeout=0; } server { listen 80; listen 443 ssl; server_name domain.com ~^.+\.domain\.com$; location / { try_files $uri @proxy; } location @proxy { proxy_pass_header Server; proxy_redirect off; proxy_set_header Host $http_host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-Forwarded-Proto https; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Scheme $scheme; proxy_connect_timeout 10; proxy_read_timeout 120; proxy_pass http://gunicorn; } } The same server needs to serve both HTTP and HTTPS, however, when the upstream issues a redirect (for instance, after a form is processed), all HTTPS requests are redirected to HTTP. The only thing I have found that will correct this issue is changing proxy_redirect to the following: proxy_redirect http:// https://; That works wonderfully for requests coming from HTTPS, but if a redirect is issued over HTTP it also redirects that to HTTPS, which is a problem. Out of desperation, I tried: if ($scheme = 'https') { proxy_redirect http:// https://; } But nginx complains that proxy_redirect isn't allowed here. The only other option I can think of is to define the two servers separately and set proxy_redirect only on the SSL one, but then I would have duplicate the rest of the conf (there's a lot in the server directive that I omitted for simplicity sake). I know I could also use an include directive to factor out the redundancy, but I really want to keep just one conf file without any dependencies. So, first, is there something I'm missing that will negate the problem entirely? Or, second, if not, is there any other way (besides including an external file) to factor out the redundant config information so that I can separate out the HTTP and HTTPS versions of the server config?

    Read the article

  • Prevent SSL certificate being returned for a specific domain

    - by jezmck
    Apologies for a long question: We've taken on a new client whose web hosting was previously on their in-house server which still has their Exchange/Outlook email. We now host their domain (and many others) on our server. They're complaining that they're getting errors in Outlook. I don't understand the AutoDiscover stuff at the root of the problem, but believe that I just need to stop the SSL certificate on our server being returned when requested at a particular domain: Yes it is, the issue lies with "{newclient}.com" being pointed to your server IP and that server has Port 443 open with an SSL certificate associated to it. So when Outlook/ActiveSync use autodiscover to find the mailbox settings it find your SSL (because 443 is open) and flags it as an error. The solution is to close 443 so its not discovered, Autodiscover will then proceed to mail.{newclient}.com via the MX / ServiceRecords and discover the correct SSL. I'm new here and there was no hand-over, so I don't know whether other currently hosted sites need to accept SSL connections, though I suspect some will, or may in future. This is a live server, so I can't risk trying loads of options in case I take the server offline! I feel like I should be adding something like the following to vhosts.conf. <VirtualHost *:443> ServerName {newclient}.com ServerAlias www.{newclient}.com SSLEngine Off SSLCertificateFile {NONE} SSLCertificateKeyFile {NONE} </VirtualHost> Apologies for the fact that I don't know enough about this subject to be able to ask the question more clearly!

    Read the article

  • Why *do* windows print queues occasionally choke on a print job

    - by Ian
    Y'know they way windows print queues will occasionally stop working with a print job at the head of the queue which just won't print and which you can't delete? Anyone know whats going on when this happens? I've been seeing this since the NT4 days and it still happens on 2008. I'm talking about standard IP connected laser printers - nothing fancy. I support a lot of servers and loads of workstations and see this happen a few times a year. The user will call saying they can't print. When you examine the print queue, which in my case will generally be a server based queue shared out to the workstations, you find a print job which you cannot cancel. You also can't pause it, reinitialize it, nothing. Stopping the spooler is the usual trick and works sometimes. However I occasionally see cases which even this doesn't cure and which a reboot is the only solution. Pause the queue, reboot, when it comes back up the job can then be deleted. Once gone the printer happily goes back to its normal state. No action is ever necessary on the printer. I regard having to reboot as last resort and don't like it. What on earth can be going on when stopping the process (spooler) and restarting it doesn't clear a problem? Its not linked to any manufacturer either. I've seen this on HPs, lexmark, canon, ricoh, on lasers, on plotters.... can't say I ever saw this on dot matrix. Anyone got any ideas as to what may be going on. Ian

    Read the article

  • will heavy network traffic affect other connections on HP ProCurve V1810-48G?

    - by nn4l
    I have a HP ProCurve V1810-48G switch with a few servers connected to it (everything in one rack). The switch is practically in its default configuration. During copying of a few hundred GByte of data from server_a to server_b (using tar cf - data | ssh server_b 'cd myhome; tar xf -'), essentially saturating the network capacity between those two servers, I noticed network related error messages on the console of server_c - as if server_c is no longer able to send/receive traffic to server_d. After canceling the copy command everything was normal again. I would understand this if the network connection would use a shared resource, for example if server_a and server_c are in one datacenter, server_b and server_d are in another datacenter and both datacenters are connected with a 100 MBit line. But all of the mentioned servers are connected to the same switch and are located in the same IP network. I always thought that a connection between two servers on one switch will not affect any other server connected to the switch. It is also possible that the network related error messages are caused by something else - but I can't risk a network problem for any other system on this switch. Please advise.

    Read the article

  • Clarification for setting up SSH terminal access on Cisco IOS

    - by Matt Malesky
    I'm attempting to set up SSH on a Cisco 2811 and having some difficulties. The first step to this should be running crypto key generate rsa I seem to be missing this though: better#crypto key generate rsa ^ % Invalid input detected at '^' marker. better# Furthermore, the only available commands I have in the crypto key namespace are lock and unlock, which seem to indicate a locked keypair (for which I don't know the password): better#crypto key ? lock Lock a keypair. unlock Unlock a keypair. better#crypto key unlock ? rsa RSA keys better#crypto key unlock rsa %% Please enter the passphrase: %% Unlocking failed. . better# More or less, I'm asking what exactly this might mean, and if I actually do have certificates already here (used router)? Otherwise, how can I solve this? It's my first time configuring this feature, but I definitely believe it's part of my IOS. Speaking of my IOS, I'm running the image c2800nm-advsecurityk9-mz.124-24.T6.bin I'll also note that I have my hostname and ip domain-name configured. I'll also give you a dir flash: below if it's at all of use: better#dir flash: Directory of flash:/ 2 -rw- 2748 Jul 27 2009 14:03:52 +00:00 sdmconfig-2811.cfg 3 -rw- 931840 Jul 27 2009 14:04:10 +00:00 es.tar 4 -rw- 1505280 Jul 27 2009 14:04:32 +00:00 common.tar 5 -rw- 1038 Jul 27 2009 14:04:46 +00:00 home.shtml 6 -rw- 112640 Jul 27 2009 14:05:00 +00:00 home.tar 7 -rw- 1697952 Jul 27 2009 14:05:26 +00:00 securedesktop-ios-3.1.1.45-k9.pkg 8 -rw- 415956 Jul 27 2009 14:05:46 +00:00 sslclient-win-1.1.4.176.pkg 9 -rw- 38732900 Dec 8 2011 06:28:56 +00:00 c2800nm-advsecurityk9-mz.124-24.T6.bin 64016384 bytes total (20598784 bytes free) better#

    Read the article

< Previous Page | 399 400 401 402 403 404 405 406 407 408 409 410  | Next Page >