Search Results

Search found 13180 results on 528 pages for 'non interactive'.

Page 405/528 | < Previous Page | 401 402 403 404 405 406 407 408 409 410 411 412  | Next Page >

• Can't install Hyper-V in Windows 8 Pro. Causes boot loop, pain & suffering

  - by Nick

  Hardware: Intel i7 2600K (not overclocked, SLAT compatible, virt. features enabled in bios) Asus Maximus IV Extreme-Z (Z68) 16Gb RAM 256Gb SSD Other non-trivial working parts Adding Hyper-V is causing a boot loop resulting in an attempt at automatic repair by Windows 8 after the second or third loop: I'm trying to get the Windows Phone 8 SDK installed and I've narrowed down my troubles to the Hyper-V feature in Win8. This is required to run the WP8 emulator and there are no install options to omit this feature. My first attempt completely borked the OS as I did not have a recent restore point or system image, so I did a completely clean install and made plenty of backups/restore points. I skipped the SDK install and went straight for the windows feature add-on for Hyper-V. This confirmed that Hyper-V is the issue as the same behavior resulted. I cannot find any hint in the Event Logs. Cancelling automatic recovery causes the same behavior to repeat. I don't have any other VM products installed. My only recourse is to use a restore point, try something else, install it again, and see what happens. No luck so far. I'm on my 10th attempt here. Any help would be much appreciated.

  Read the article

• OS X won't boot up unless I hold down option key

  - by Gazzer

  I have a strange issue on an early 2008 Mac Pro running OS 10.6: if I restart the computer it restarts normally if I shutdown and boot, it stops at the grey screen just before the boot process if I shutdown and boot but hold down the option key, I can select the boot disk and all is good. I've just cloned the disk, and the same thing happens. The disk is a SAMSUNG HD154UI The disk is partitioned (the second partition holds a clone of the Snow Leopard Install disk) One weird thing on the original disk was one of the partitions said 'EFI Boot' in a non-aliased font rather than the name of the disk when the disks are listed upon holding down option. Solution: it seems that there was a problem with the disk. Part of the difficulty in finding the solution was that you need to remove the disk from the computer completely. For example, a good disk in Bay 3, wouldn't boot up if the bad disk was in Bay 2. So for ages I thought the problem was hardware related in Bay 3. So if you think you have a dodgy disk remove it totally if you are testing the hardware with a 'clean' disk. Cleaning the PRAM helped to get the new disk to work too.

  Read the article

• How can I stop Excel from eating my delicious CSV files and excreting useless data?

  - by atroon

  I have a database which tracks sales of widgets by serial number. Users enter purchaser data and quantity, and scan each widget into a custom client program. They then finalize the order. This all works flawlessly. Some customers want an Excel-compatible spreadsheet of the widgets they have purchased. We generate this with a PHP script which queries the database and outputs the result as a CSV with the store name and associated data. This works perfectly well too. When opened in a text editor such as Notepad or vi, the file looks like this: "Account Number","Store Name","S1","S2","S3","Widget Type","Date" "4173","SpeedyCorp","268435459705526269","","268435459705526269","848 Model Widget","2011-01-17" As you can see, the serial numbers are present (in this case twice, not all secondary serials are the same) and are long strings of numbers. When this file is opened in Excel, the result becomes: Account Number Store Name S1 S2 S3 Widget Type Date 4173 SpeedyCorp 2.68435E+17 2.68435E+17 848 Model Widget 2011-01-17 As you may have observed, the serial numbers are enclosed by double quotes. Excel does not seem to respect text qualifiers in .csv files. When importing these files into Access, we have zero difficulty. When opening them as text, no trouble at all. But Excel, without fail, converts these files into useless garbage. Trying to instruct end users in the art of opening a CSV file with a non-default application is becoming, shall we say, tiresome. Is there hope? Is there a setting I've been unable to find? This seems to be the case with Excel 2003, 2007, and 2010.

  Read the article

• Is there a remote desktop or vnc app for the IPad that properly handles Bluetooth keyboard shortcuts?

  - by Steve Bison

  I've tried 4 or 5 remote desktop apps, the most notable being Jump Desktop and Splashtop Streamer. Most of these remote desktop apps have some sort of on-screen keyboard for typing with the IPad, including special keys like shift, control, alt. The special keys act like "sticky keys" meaning they stay depressed until another key is pressed, to make it easier to do key combinations. Even non-standard keyboard combinations like shift+enter work, in this sticky sense. When using a Bluetooth keyboard with the remote desktop apps, both Jump and Splashtop Streamer recognize the shift + letter combination for doing capital letters. However, generically pressing shift, cntrl, or alt does not depress the sticky on screen shift buttons or do anything at all. Only a few combinations are recognized (again like shift+letter, cntrl+C). Most combinations do not work (shift+enter, alt+tab). Even having the keyboard shortcuts work like sticky keys (press shift then enter, not both at once) would be much better than the limited functionality they have now. Is there an app, jailbreak app, or workaround that lets me use bluetooth keyboard properly with remote desktop on the ipad?

  Read the article

• Easiest way to do host name resolution with IPA?

  - by Luke

  We are currently using static LAN IP addresses for our internal non-public facing servers. We don't have DHCP configured. We're using Vyatta for our router and firewall. The firewall is configured to be zone based. We want to setup IPA for centralized authentication (LDAP+Kerberos). IPA is requiring resolvable host names. I want to avoid having to enter DNS records by hand. What is the most painless way to make host names resolvable that works with IPA in a Linux only environment? We arn't using anything to resolve host names now. Up until now we've been using static ip addresses and local users on each server. We've looked at BIND, DHCP (does that even solve the problem?), and multicast DNS. At this point we're not sure which solution would work best. Is there another option we haven't considered? Security is very important. We have multiple zones where each zone has very specific or no access to another zone. DNS for public domains is forwarded from Vyatta to our ISP's DNS server.

  Read the article

• Can't mount Linux usd disk. It just create /dev/sg device but no /dev/sd

  - by MTilsted

  I have a Corsair R60 ssd disk which is a disk with both sata and usb connectors. But the usb thing seems to be a bit non-standard, or maybe its just my fedora linux. When I insert the disk using a usb cabel to a running Fedora 14 linux system, a device called /dev/sg3 is added but that is all. No new /dev/sd* device is created so I can't mount the disk. If I look at cat /proc/scsi/sg/device_strs I get ATA Hitachi HTS54321 FB2O HL-DT-ST DVDRAM GSA-T50N RP05 Seagate Desktop 0130 Corsair CSSD-R60GB2 So the disk is there. (The last entry) but my linux will for some reason not see it as a usb hard disk. When I insert other usb disks they work fine. It is only this specific disk which causes problems. I have tried on 3 different computers with the same result. A hint to the problem may be that if I add the disk to a windows system(With usb) the disk is called "A fixed disk" and not a portable disk as expected. The disk works fine with linux If i connect it with the sata cabel, but I would really like to have it working with usb too. (To mount it on computers without sata).

  Read the article

• Strange problem with Google Mail and IMAP on Outlook 2007

  - by Alex C.

  I work for a small non-profit organization. We have about 35 administrative employees who use e-mail. We're on a Windows network with a domain. Everyone is running XP Pro and Office 2007 with all updates/patches. We used to use POP3 mail through a local provider. However, we recently signed-up for a free Google Apps account, and we switched to IMAP mail through Google. Everyone uses Outlook 2007 as the client. For about ten days, everything was working fine. Yesterday afternoon, we suddenly developed a strange and annoying problem. Every time you send an e-mail message, a copy of your outgoing message shows up in your inbox. It's as if you're adding your own address to the CC: line of every message. Nothing has changed on our end. I was hoping that the problem was a temporary glitch that would resolve itself, but here we are about 24 hours later, and it's still happening. I searched Twitter, and there were a handful of vague messages about issues with Google mail and IMAP, but I didn't see any references to this specific problem. Any thoughts on what's going on here and how to fix it?

  Read the article

• Load is 0, yet site crawls (sometimes). What gives?

  - by Yegor

  I have a ~1.5-2mil page views per day site running on 2 servers. One for mysql, other for everything else. Mysql box has a load of 3, frontend is usually 0.0-0.1. Both are dual quad core with 8GB ram running SAS drives in raid5. CPU is idle for majority of the time, iowait is non-existent. Im running nginx, memcache, and site is built on php. Half the time everything runs perfect, while at other times it lags something severe, when it takes 10-15 seconds for a page to load. Page execution time is always super low, but it seems to hang, waiting for something before it actually loads the page. Whats even more weird is that it only happens to 1 file on the site (but its the one thats most commonly accessed, that actually loads the content on the site). Other pages are super fast at all times, even when it takes 15 seconds to load actual content. I have nginx_stats plugin installed, and if I monitor it, the lag spikes happen when the write column starts going above 100, and it frequently does... all the way to 500-1000. It does so at totally random times... not when traffic is heavy... it can do this in the middle of the night, and work perfectly at 5pm when traffic is at its highest. Any ideas?

  Read the article

• Provider claiming "all web servers in the cloud are automatically kept in sync" - should I be skeptical?

  - by RobMasters

  I'm no expert in cloud computing - I've spent a fair bit of time researching it and various providers but am yet to get any hands-on experience with it. From what I've read about AWS and auto-scaling EC2 instances though, it seems as though each instance should be completely decoupled from all other instances. i.e. If content is uploaded to the web server's local filesystem from a custom CMS backend then that content won't be available if subsequently requested from a different web server in the auto-scaling group. Is that right? I met with a representative of our existing hosting provider recently and he was claiming that it isn't a problem that our legacy CMS system is highly dependent on having a local filesystem. He said that all web servers, regardless of how many, would be kept as exact duplicates so I shouldn't notice any difference compared to our existing setup of a single dedicated server. This smells a little too much like bull fecal-matter to me...should I be skeptical about this? I'm a little worried because my (non-technical) boss who ultimately makes the decisions is all for signing up to this cloud solution because it won't require any extra work. I'm sure that they must at least be able to provide this, otherwise they wouldn't be attempting to sell it to us. But at what cost? It sounds as though each web server will always need to be checking the other web server(s) for new static content, which to me sounds like unwanted overhead that'll slow things down. I'd really appreciate it if somebody could clear this up to me. I'm all for switching to AWS and using S3+CloudFront for all static content, but that isn't looking very likely to happen at the moment.

  Read the article

• Running batch file through a service.

  - by wallz

  I'm trying to schedule a batch file to run through a third party application, however the output file doesn't get created in the directory. If I run the .BAT file from the command line, it works and the file gets created. Also using the Windows Schedule will also succeed. Basically, the 3rd party software will schedule the .BAT file and it shows success within the 3rd party user interface. The difference between running from the command prompt and the software, is that the software will use its Windows service to launch the batch. The 3rd party software will show success since it was able to successfully call the .BAT file to run, however it has no control of the other EXE's that's being called within the script. I'm able to run a simple .BAT file in the 3rd party software, for example a copy command. The .BAT I'm having problems with calls a compiled EXE which launches Excel to create a file to a location. The .bat file calls something.exe, which then calls Excel.exe: C:\something.exe -o D:\filename.xlsm C:\filename.xlsm refresh_pivot Do you think it's a permissions issue? I used Process Monitor to verify any Access Denied errors but everything seems to be working according to the trace. It worked on a non-64-bit OS, I'm currently using Win2008 64-bit.

  Read the article

• Linux as a router for public networks

  - by nixnotwin

  My ISP had given me a /30 network. Later, when I wanted more public ips, I requested for a /29 network. I was told to keep using my earlier /30 network on the interface which is facing ISP, and the newly given /29 network should be used on the other interface which connects to my NAT router and servers. This is what I got from the isp: WAN IP: 179.xxx.4.128/30 CUSTOMER IP : 179.xxx.4.130 ISP GATEWAY IP:179.xxx.4.129 SUBNET : 255.255.255.252 LAN IPS: 179.xxx.139.224/29 GATEWAY IP :179.xxx.139.225 SUBNET : 255.255.255.248 I have a Ubuntu pc which has two interfaces. So I am planning to do the following: eth0 will be given 179.xxx.4.130/30 gateway 179.xxx.4.129 eth1 will be given 179.xxx.139.225/29 And I will have the following in the /etc/sysctl.conf: net.ipv4.ip_forward=1 These will be iptables rules: iptables -A FORWARD -i eth0 -o eth1 -j ACCEPT iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT My clients which have the ips 179.xxx.139.226/29 and 179.xxx.139.227/29 will be made to use 179.xxx.139.225/29 as gateway. Will this configuration work for me? Any comments? If it works, what iptables rules can I use to have a bit of security? P.S. Both networks are non-private and there is no NATing.

  Read the article

• Changing SkyDrive default location on Windows 8.1

  - by jmblack

  Update: This issue is due to the use of any non-local location for the SkyDrive folder. I've currently worked around this by using a local folder, but this has not resolved the original problem. I am trying to change the location where SkyDrive is located in Windows 8.1. This is the newly integrated SkyDrive, and not a downloadable client. There are a couple of similar questions on this site, but they pertain to Windows 8 and 8.1 Preview: Changing the SkyDrive default path in Windows 8.1 (Windows 8.1 Preview) How do I change the SkyDrive default folder in Windows (Windows 8) The SkyDrive folder is a system folder in 8.1, and like other system folders, has a Location tab in its properties that theoretically lets you change its location. I was able to do this with other system folders such as Downloads and Pictures, but there is an error when I try to change this for SkyDrive. Edit: The location that causes this error is a mapped network drive. The error does not occur when trying to move SkyDrive to another location on the same drive. There are no permission restrictions on the mapped network drive. Edit #2: This is the method I followed that produced the error: A screenshot of the error can be found here Has anyone else encountered this or have any information on this?

  Read the article

• How do I access my webserver on my stationary from my laptop?

  - by Steven

  I'm running Apache on my stationary and I would like to access a website through my laptop. This is some of the Apache config: NameVirtualHost 127.0.0.1:80 <VirtualHost 127.0.0.1:80> ServerName mysite.com DocumentRoot I:/wamp/www/mysite/ </VirtualHost> ServerName localhost:80 <Directory /> Options FollowSymLinks AllowOverride all Order deny,allow Deny from all </Directory> On my laptop I've added the following to the HOSTS file: 10.0.0.3 mysite.com But accessing the page through mysite.com is not very successfull. If I enter the IP address directly, I only get a Forbidden message. What do I need to do in order to get this to work? Update I'm runing WAMPSERVER 2.1 (Apache 2.2.17) Apache is up and running I can ping 10.0.0.3 from laptop I'm not able to ping http://mysite.com from laptop IE gives me a 403 Forbidden - The website declined to show this webpage The only log that get's entries when trying to access the website from my laptop, is access.log. access.log 10.0.0.4 - - [13/Jun/2011:10:14:04 +0200] "GET / HTTP/1.1" 403 202 apache_error.log [Mon Jun 13 10:08:16 2011] [error] VirtualHost localhost:0 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results UPDATE 2 My apache config has the following entry: AllowOverride all Order Deny,Allow Deny from all Allow from 127.0.0.1 Could it be that this Allow from is stopping other computers accessing the page?

  Read the article

• Computer does not boot, often

  - by tam

  I've ran into a issue with my computer that it does no longer reach POST, but simply powers on for a fraction of a second and powers off. But this is not always, some times it boots just normally and it works as it should, no issues with not enough power or anything. But as soon as I turn it of, I can not turn it back on, but then again at some random point it just powers up again, and resumes normal operation. If I disconnect the 8pin ATX connector from the motherboard, it powers up, fans and disks spinning normally until I power it off again. So this problem only happens when ATX is connected, which seems odd, I normally always saw this kind of an error if ATX was not connected, but here it's the exact opposite. It also does not emit any sound on the buzzer, except the normal beep, when it powers up normally. I have already tried: Remove graphics card Remove one and/or all RAM sticks Disconnect everything non-essential, even hard drives Clear CMOS I have not yet tried to remove all components and tried to boot everything outside of the case, because I did not have the time to disassemble and bleed the water loop. However, I can confirm that nothing is stuck underneath the motherboard, not is any of those brass raisers touching the board where it should not. Specs: Gigabyte GA-970A-UD3 AMD FX6300 ATI HD7850 I think this should be enough for this issue.

  Read the article

• Help with Ubuntu and Windows, separate HDs

  - by LuxuryMode

  Need some major help. Running a Dell XPS/Dimension 630i. It came with "SATA 2 RAID 0 With Dual 500GB Hard Drives." I have installed a new, third non-raided drive and installed Ubuntu on it. So now I have Windows on the original hard drive and Ubuntu Linux on the new HD. When I get to the boot menu where I can select an OS, if I select windows I get an error: "No such drive, no such disk." Also, strangely in the first place, in order to even get to the bootloader menu I have had to disable ALL ports under the RAID config. Unless I do this, I will just get to a never-ending blinking cursor. I have tried every conceivable CMOS config and nothing else works. Tried setting port 3 (the new HD w/ Ubuntu) to first hard disk boot priority. Tried disabling all other ports and enabling the Ubuntu HD port and vice versa. I have some pictures of boot up: first one is strange error i get after messing with CMOS to finally get ubuntu install to work. http://imgur.com/5sqJa then boot menu: http://imgur.com/TWtLq then error: http://imgur.com/TJ1mS. Also, please note that I can actually access all files from the raided Windows drive through Ubuntu.

  Read the article

• Windows disk change monitoring for malware analysis

  - by SuperDuck

  Not sure if this question belongs to here, because it has some relations with 'serverfault' (system backups) and 'stackoverflow' (software analysis). I'm looking for a solution to monitor disk changes on a Windows system and selectively revert them. It should be able to handle live files like registry parts, so may need to be an offline backup software. It shouldn't silently pass over files which the current admin user doesn't have permissions on (files with no permission entries or owned by the 'system' user) Registry change tracking would be a bonus but is not a requirement I use virtual machines for malware analysis, there is even no solution to list file changes in disk snapshot files (delta VMDK). I currently use Ashampoo for monitoring changes. Though it's the best one between similars, it's not a good software and hasn't really evolved in many 'platinum', 'deluxe' versions released in the last 10 years (it even used non-resizable windows until the latest version). The real problem is it misses some disk / registry changes. Perhaps it only compares modification dates and doesn't catch a change if the dates are preserved. So, I think the solution should compare files using hashes, or file sizes at least. There are numerous backup software out there and I'm sure one can handle this, offline or online.

  Read the article

• Disable internal display on Macbook Pro without closed lid mode?

  - by jslaker

  I have an early 2007 Macbook Pro running 10.5 that I've recently set up on a KVM with my primary desktop system. The problem I've run into is that I have a 20" 1680x1050 LCD, and OS X only provides options to mirror at the resolution of the built-in display or to span. Since the built-in display runs at 1440x900, this leads to running my LCD at non-native res and a fuzzy picture. There isn't any option that I can find to simply disable the built-in display entirely and run the external LCD at its native resolution. I am aware of closed lid mode, but the MBP was disassembled while in storage for about 6 months (took it apart to pull the HDD) and the cable to the touchpad, which controls the sleep sensor was damaged, meaning closed lid mode won't work. I've looked into replacing the cable, but the cheapest I've been able to find it is $75-100, and I'm trying not to invest any more money into this computer as it also has a completely dead battery and a few other minor problems. I've found the app SwitchResX which appears to allow you to do what I need, but it has a lot of functionality I don't need and a ~$20 registration charge attached to it. An odd set of circumstances, I'm aware, but I was hoping somebody might know of an OS hack that would let me just disable the internal display and be done with it. :)

  Read the article

• Computer loop restarts on Windows loading

  - by Robinson G.

  My computer restarts, just after or during Windows loading (4 squares getting together), or after some time on the desktop IF I'm idle. In order to start the computer I either have to swap my RAM (24Go) in differents DIMM slots, for example (I have 4 slots) : 1-2-4 or 2-3-4 or 1-3-4, not the same position each boot or it restarts in a loop... I can also change the ram timing from 1.5 to 1.6V and it starts, at the next reboot I have to change it again to 1.5 or it won't boot... And If after all, I succeed to boot, I have to use the computer for about 10 minutes, and it's ok, if I don't, it restarts by itself after some minutes. If I stay on the BIOS, It's all OK, I can stay for a whole year without restarting. I have check my RAM on Memtest (4*8G SDRAM DDR3) : OK I have check without graphic card : Still the same. I tried to reset the bios stack by getting it off and on : Still the same. I tried to reset my BIOS, and many settings about the RAM in the menu : Still the same. CPU temps are just fine (around 35°C) I was thinking ofc about the motherboard but I want to be sure. Motherboard : MSI zh77a-g43 RAM : 4*8G Dual Mode or not (depends on the number I put ofc.) PSU : 600W (enough to run all the config) CPU : i7 3770 non K

  Read the article

• FTP account ownership on vhost directory makes Apache not run website correctly

  - by CodeShining

  I've purchased a virtual server, where I'm given of a non-root sudo-enabled user. Actually I do need to create an FTP account that's not that sudo-able account, so I created a no-login account just for that purpose. I've set up VSFTPd correctly, also enabling the "userlist" feature, to specify which user are permitted to use FTP. Then I created an empty directory under my sudo-able account, and I gave ownership permissions to the second account, so to make it more easy to understand, let's say the main account (the one I do use to manage my VPS) is called ubuntu and the FTP-user is named ftpuser, I created a directory /home/ubuntu/mywebsite giving the ownership to ftpuser:ftpuser. Then I uploaded a worpdress website, whose default permissions are 755 and 644. The issue is that Apache is not given of any privilege to run the website. How can I make the website run properly, and which is the most secure? Should I run that virtualhost with another user (if it's possible)? Should I force the FTP user to use the www-data group (if that's possible) and run with permissions like 775 and 664? How can I solve this issue? Any help is appreciated, I'd like to run it using the default permissions, so any update won't break up anything (because of permissions reset).

  Read the article

• setting the PATH for Git (not for me)

  - by Iain

  Hi, I'm running OSX 10.6.5 with Git 1.7.1 I have git installed in a non-standard location (though that really should be the standard on a mac;-) in /Library/Frameworks/Git.framework. My own PATH is set fine, git works fine, until... I set up a pre-commit hook with a Ruby script: $ git commit -m "added some Yard documentation" .git/hooks/pre-commit: line 1: #!/usr/bin/env: No such file or directory The pre-commit.sample runs ok, so it appears that git can't find /usr/bin/env, or much else as I've tried shebanging it directly to ruby etc. Just /bin/sh is ok. So, where does Git get it's PATH? because it's not using mine or this wouldn't be happening. And more to the point, how do I get it to see /usr/bin/env ? I've tested the ruby script already, it works. Just to add: $ cat /etc/paths /usr/bin /bin /usr/sbin /sbin /usr/local/bin $ cat /etc/paths.d/git /Library/Frameworks/Git.framework/Programs The first few lines of the Ruby script (which runs via ./pre-commit or ruby pre-commit) #!/usr/bin/env ruby -wKU class String def expand_path File.expand_path self end def parent_dir File.dirname self.expand_path end end

  Read the article

• One Way Sync with Dropbox?

  - by user244805

  Is there any way I can mirror a dropbox folder to my C drive by just running a portable file? Extra background information because I know you guys hate it when you don't get the entire situation: I go back to University in fall and I need a new storage solution. I decided to use DropBox to sync my tiny University files (< 5 MB). I need to access these files from 4 machines: Windows 7 Home machine Windows 7 University A machine Windows 7 University B machine Android tablet 1 and 4 are a non-issue. The problem lies with 2 and 3. I want to be able to edit my files on 2 and 3 but those machines are not mine. There is an easy fix. Run a portable version of the DropBox syncer on a USB drive. But the problem is that I don't want to carry a USB drive around with me all the time. In that case, I can just run the small portable DropBox syncer off the internet. But where will it to store the files? A temporary directory on the C drive. There is only one issue left: there are hundreds of machines that I will randomly use that fit in categories 2 and 3. My portable DropBox syncer will notice that the temporary directory is empty on each new PC I use and instead of downloading my DropBox folder to the machine, it syncs the other way around i.e. it deletes my entire DropBox. The solution is to mirror my DropBox onto the temporary directory before running the DropBox syncer.

  Read the article

• exim4 seem to stop listening

  - by trakos

  Hey, I have a strange problem with my exim4 configuration. I have a dedicated server running debian for quite a long time now, but I'm not really using it actively recently, so everything just worked due to lack of changes ;) However, recently, my exim4 smtp stopped answering on port 25. It does not respond through localhost, as well - even though it's set to listen on any interface available. Some things I've checked: ks:/home/trakos/Maildir/new# netstat -ap | grep exim tcp 0 0 *:smtp : LISTEN 12521/exim4 ks:/home/trakos/Maildir/new# exiwhat 12521 daemon: -q30s, listening for SMTP on port 25 (IPv4) ks:/home/trakos/Maildir/new# cat /var/log/exim4/rejectlog ks:/home/trakos/Maildir/new# cat /var/log/exim4/paniclog The queue is set for 30s only because I was running it in a non-daemon mode to see any output. Strangely enough, no suspicious output is given, netstat even shows it is listening on port 25, but still trying to telnet to it times out. The only things that may have changed recently are: I've got second IP for my server I remember that few days ago my spamassasin crashed, and I've started it up again So yeah, I'm really clueless about this one now :P I mean, I don't even know what could be failing here. Could someone give me some ideas what should I check next? PS: it has uptime of 442 days, so I haven't really tried rebooting it yet ^^

  Read the article

• Viewing Postscript (or PDF) on OS X: Aliasing issues

  - by mankoff

  I am generating postscript graphics and am trying to find a balance between non-aliasing and over-aliasing. If I use the raw ghostscript viewer gs on the Postscript, it looks good. The text appears anti-aliased, but the image remains nice and blocky. Unfortunately, gs has no real user interface and loses all of the nice things that Preview.app has. I could install gv, but the dependency bloat is huge! It requires all of gnome. And even that isn't a great viewer compared to Preview.app or Skim.app. Here is an image viewed with gs: From a user-interaction and Mac-ish perspective, Preview.app (or Skim.app is a much nicer program to use. They have the option to turn on or off aliasing, but neither option looks very good. Which aliasing on, the image is blurry. When it is off, the graphic matches what is seen from gs, but there are two issues. Minor issue: the font is ugly. Uglier than with gs. Major issue: Every PDF is un-aliased, making it hard to read regular PDFs full of text. So, in summary: Is there a way to manually generate the PDF from the PS that overcomes these issues? Is there a way to find a middle ground of alias/unalias with Preview.app? Is there another app that displays with quality like gs, but has a decent UI like Skim.app or Preview.app Is there a way to have Preview.app turn off aliasing for only one file (containing graphics) but leave it enabled in general so that text PDFs are still readable?

  Read the article

• How to change password on RAR archive w/o modifying arch. files attributes (modified/created)?

  - by Larry78

  How do I change the password of an .RAR archive, without changing the date/time attributes of the files in the archive? Unfortunately you can't directly change the password of the archive with WinRAR, you have to extract the files, and then make a new archive with the new password. So the created/modified attributes of the files in the archive get changed. I know you can manually change the attributes of a file with available utilities - but there are hundreds of files in the archive, each with unique attributes, so it would take a very long time to "fix" each file before re-archiving it. I'm using WinRAR 3.51, the last free version. Windows XP Pro SP3. Update: I don't care if the output is a .RAR file or a ZIP file IZArc4.1 will convert the RAR to a ZIP, and it keeps the dates. The problem is it compresses the file - there isn't a "store" option, and setting the default to store in the main configuration doesn't effect conversions. The RAR contains uncompressed files. None of these other archiving programs will even do a conversion. A couple claim to, or try to, but the errors returned indicate a very lousy application. So far I've tried PeaZip, 7-Zip, FilZip, TugZip, SimplyZipSE, QuickZip, and WinShrink (from downloads.cnet.com). WinRAR gives the error "skipping encryped archive" when I try the conversion. It asks for the password first, and I know it's right, as I opened the archive, and I can read/view all the files in it. It works on non-encrypted files.

  Read the article

• RAID-capable 3.5" SATA Drives

  - by nroam

  I recently purchased a pair of 1TB Western Digital WD1002FBYS RE3 drives for use in an external RAID enclosure. I have found that they tend to drop out of the array after a while. Thinking it was the enclosure I tried them on another one but found the same issue. So a bit of googling and I found http://www.tomshardware.com/forum/251076-32-raid-issues-western-digital-hard-disk which suggests that: "WD's "RE" (RAID Edition) HDDs support Time-Limited Error Recovery ("TLER" ): http://www.wdc.com/en/products/productcatalog.asp?language=en As a non-TLER HDD fills up with data, the error detection firmware might take too long, and the RAID controller may drop that HDD from a RAID array." So now I wonder what SATA drives have firmware which is compatible with RAID arrays (esp. RAID 1, 5, but not 0)? I have not been able to come up with the magic set of keywords to ellicit the answer from Google. However, various sites suggest that Seagate & Hitachi are in general OK. Does anyone have any generic (or even specific) guidance on how to work out if a drive's firmware may harbour code that is potentially an issue in a RAID0 setting other than stating that it must be 'enterprise' ready?

  Read the article

< Previous Page | 401 402 403 404 405 406 407 408 409 410 411 412  | Next Page >