Search Results

Search found 10812 results on 433 pages for 'boot partition'.

Page 407/433 | < Previous Page | 403 404 405 406 407 408 409 410 411 412 413 414  | Next Page >

• Cannot open root device xvda1 or unknown-block(0,0)

  - by svoop

  I'm putting together a Dom0 and three DomU (all Gentoo) with kernel 3.5.7 and Xen 4.1.1. Each Dom has it's own md (md0 for Dom0, md1 for Dom1 etc). Dom0 works fine so far, however, I'm stuck trying to create DomUs. It appears the xvda1 device on DomU is not created or accessible: Parsing config file dom1 domainbuilder: detail: xc_dom_allocate: cmdline="root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3", features="(null)" domainbuilder: detail: xc_dom_kernel_mem: called domainbuilder: detail: xc_dom_boot_xen_init: ver 4.1, caps xen-3.0-x86_64 xen-3.0-x86_32p hvm-3.0-x86_32 hvm-3.0-x86_32p hvm-3.0-x86_64 domainbuilder: detail: xc_dom_parse_image: called domainbuilder: detail: xc_dom_find_loader: trying multiboot-binary loader ... domainbuilder: detail: loader probe failed domainbuilder: detail: xc_dom_find_loader: trying Linux bzImage loader ... domainbuilder: detail: xc_dom_malloc : 10530 kB domainbuilder: detail: xc_dom_do_gunzip: unzip ok, 0x2f7a4f -> 0xa48888 domainbuilder: detail: loader probe OK xc: detail: elf_parse_binary: phdr: paddr=0x1000000 memsz=0x558000 xc: detail: elf_parse_binary: phdr: paddr=0x1558000 memsz=0x690e8 xc: detail: elf_parse_binary: phdr: paddr=0x15c2000 memsz=0x127c0 xc: detail: elf_parse_binary: phdr: paddr=0x15d5000 memsz=0x533000 xc: detail: elf_parse_binary: memory: 0x1000000 -> 0x1b08000 xc: detail: elf_xen_parse_note: GUEST_OS = "linux" xc: detail: elf_xen_parse_note: GUEST_VERSION = "2.6" xc: detail: elf_xen_parse_note: XEN_VERSION = "xen-3.0" xc: detail: elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000 xc: detail: elf_xen_parse_note: ENTRY = 0xffffffff815d5210 xc: detail: elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff81001000 xc: detail: elf_xen_parse_note: FEATURES = "!writable_page_tables|pae_pgdir_above_4gb" xc: detail: elf_xen_parse_note: PAE_MODE = "yes" xc: detail: elf_xen_parse_note: LOADER = "generic" xc: detail: elf_xen_parse_note: unknown xen elf note (0xd) xc: detail: elf_xen_parse_note: SUSPEND_CANCEL = 0x1 xc: detail: elf_xen_parse_note: HV_START_LOW = 0xffff800000000000 xc: detail: elf_xen_parse_note: PADDR_OFFSET = 0x0 xc: detail: elf_xen_addr_calc_check: addresses: xc: detail: virt_base = 0xffffffff80000000 xc: detail: elf_paddr_offset = 0x0 xc: detail: virt_offset = 0xffffffff80000000 xc: detail: virt_kstart = 0xffffffff81000000 xc: detail: virt_kend = 0xffffffff81b08000 xc: detail: virt_entry = 0xffffffff815d5210 xc: detail: p2m_base = 0xffffffffffffffff domainbuilder: detail: xc_dom_parse_elf_kernel: xen-3.0-x86_64: 0xffffffff81000000 -> 0xffffffff81b08000 domainbuilder: detail: xc_dom_mem_init: mem 5000 MB, pages 0x138800 pages, 4k each domainbuilder: detail: xc_dom_mem_init: 0x138800 pages domainbuilder: detail: xc_dom_boot_mem_init: called domainbuilder: detail: x86_compat: guest xen-3.0-x86_64, address size 64 domainbuilder: detail: xc_dom_malloc : 10000 kB domainbuilder: detail: xc_dom_build_image: called domainbuilder: detail: xc_dom_alloc_segment: kernel : 0xffffffff81000000 -> 0xffffffff81b08000 (pfn 0x1000 + 0xb08 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x1000+0xb08 at 0x7fdec9b85000 xc: detail: elf_load_binary: phdr 0 at 0x0x7fdec9b85000 -> 0x0x7fdeca0dd000 xc: detail: elf_load_binary: phdr 1 at 0x0x7fdeca0dd000 -> 0x0x7fdeca1460e8 xc: detail: elf_load_binary: phdr 2 at 0x0x7fdeca147000 -> 0x0x7fdeca1597c0 xc: detail: elf_load_binary: phdr 3 at 0x0x7fdeca15a000 -> 0x0x7fdeca1cd000 domainbuilder: detail: xc_dom_alloc_segment: phys2mach : 0xffffffff81b08000 -> 0xffffffff824cc000 (pfn 0x1b08 + 0x9c4 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x1b08+0x9c4 at 0x7fdec91c1000 domainbuilder: detail: xc_dom_alloc_page : start info : 0xffffffff824cc000 (pfn 0x24cc) domainbuilder: detail: xc_dom_alloc_page : xenstore : 0xffffffff824cd000 (pfn 0x24cd) domainbuilder: detail: xc_dom_alloc_page : console : 0xffffffff824ce000 (pfn 0x24ce) domainbuilder: detail: nr_page_tables: 0x0000ffffffffffff/48: 0xffff000000000000 -> 0xffffffffffffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x0000007fffffffff/39: 0xffffff8000000000 -> 0xffffffffffffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x000000003fffffff/30: 0xffffffff80000000 -> 0xffffffffbfffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x00000000001fffff/21: 0xffffffff80000000 -> 0xffffffff827fffff, 20 table(s) domainbuilder: detail: xc_dom_alloc_segment: page tables : 0xffffffff824cf000 -> 0xffffffff824e6000 (pfn 0x24cf + 0x17 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x24cf+0x17 at 0x7fdece676000 domainbuilder: detail: xc_dom_alloc_page : boot stack : 0xffffffff824e6000 (pfn 0x24e6) domainbuilder: detail: xc_dom_build_image : virt_alloc_end : 0xffffffff824e7000 domainbuilder: detail: xc_dom_build_image : virt_pgtab_end : 0xffffffff82800000 domainbuilder: detail: xc_dom_boot_image: called domainbuilder: detail: arch_setup_bootearly: doing nothing domainbuilder: detail: xc_dom_compat_check: supported guest type: xen-3.0-x86_64 <= matches domainbuilder: detail: xc_dom_compat_check: supported guest type: xen-3.0-x86_32p domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_32 domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_32p domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_64 domainbuilder: detail: xc_dom_update_guest_p2m: dst 64bit, pages 0x138800 domainbuilder: detail: clear_page: pfn 0x24ce, mfn 0x37ddee domainbuilder: detail: clear_page: pfn 0x24cd, mfn 0x37ddef domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x24cc+0x1 at 0x7fdece675000 domainbuilder: detail: start_info_x86_64: called domainbuilder: detail: setup_hypercall_page: vaddr=0xffffffff81001000 pfn=0x1001 domainbuilder: detail: domain builder memory footprint domainbuilder: detail: allocated domainbuilder: detail: malloc : 20658 kB domainbuilder: detail: anon mmap : 0 bytes domainbuilder: detail: mapped domainbuilder: detail: file mmap : 0 bytes domainbuilder: detail: domU mmap : 21392 kB domainbuilder: detail: arch_setup_bootlate: shared_info: pfn 0x0, mfn 0xbaa6f domainbuilder: detail: shared_info_x86_64: called domainbuilder: detail: vcpu_x86_64: called domainbuilder: detail: vcpu_x86_64: cr3: pfn 0x24cf mfn 0x37dded domainbuilder: detail: launch_vm: called, ctxt=0x7fff224e4ea0 domainbuilder: detail: xc_dom_release: called Daemon running with PID 4639 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.5.7-gentoo (root@majordomo) (gcc version 4.5.4 (Gentoo 4.5.4 p1.0, pie-0.4.7) ) #1 SMP Tue Nov 20 10:49:51 CET 2012 [ 0.000000] Command line: root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3 [ 0.000000] ACPI in unprivileged domain disabled [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x000000000009ffff] usable [ 0.000000] Xen: [mem 0x00000000000a0000-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000138ffffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] MPS support code is not built-in. [ 0.000000] Using acpi=off or acpi=noirq or pci=noacpi may have problem [ 0.000000] DMI not present or invalid. [ 0.000000] No AGP bridge found [ 0.000000] e820: last_pfn = 0x139000 max_arch_pfn = 0x400000000 [ 0.000000] e820: last_pfn = 0x100000 max_arch_pfn = 0x400000000 [ 0.000000] init_memory_mapping: [mem 0x00000000-0xffffffff] [ 0.000000] init_memory_mapping: [mem 0x100000000-0x138ffffff] [ 0.000000] NUMA turned off [ 0.000000] Faking a node at [mem 0x0000000000000000-0x0000000138ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x138ffffff] [ 0.000000] NODE_DATA [mem 0x1387fc000-0x1387fffff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00010000-0x00ffffff] [ 0.000000] DMA32 [mem 0x01000000-0xffffffff] [ 0.000000] Normal [mem 0x100000000-0x138ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00010000-0x0009ffff] [ 0.000000] node 0: [mem 0x00100000-0x138ffffff] [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] No local APIC present [ 0.000000] APIC: disable apic facility [ 0.000000] APIC: switched to apic NOOP [ 0.000000] e820: cannot find a gap in the 32bit address range [ 0.000000] e820: PCI devices with unassigned 32bit BARs may break! [ 0.000000] e820: [mem 0x139100000-0x1394fffff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on Xen [ 0.000000] Xen version: 4.1.1 (preserve-AD) [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:1 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 26 pages/cpu @ffff880138400000 s75712 r8192 d22592 u2097152 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1259871 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Memory: 4943980k/5128192k available (3937k kernel code, 448k absent, 183764k reserved, 1951k data, 524k init) [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:4352 nr_irqs:256 16 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] console [hvc0] enabled [ 0.000000] installing Xen timer for CPU 0 [ 0.000000] Detected 3411.602 MHz processor. [ 0.000999] Calibrating delay loop (skipped), value calculated using timer frequency.. 6823.20 BogoMIPS (lpj=3411602) [ 0.000999] pid_max: default: 32768 minimum: 301 [ 0.000999] Security Framework initialized [ 0.001355] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.002974] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.003441] Mount-cache hash table entries: 256 [ 0.003595] Initializing cgroup subsys cpuacct [ 0.003599] Initializing cgroup subsys freezer [ 0.003637] ENERGY_PERF_BIAS: Set to 'normal', was 'performance' [ 0.003637] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8) [ 0.003643] CPU: Physical Processor ID: 0 [ 0.003645] CPU: Processor Core ID: 0 [ 0.003702] SMP alternatives: switching to UP code [ 0.011791] Freeing SMP alternatives: 12k freed [ 0.011835] Performance Events: unsupported p6 CPU model 42 no PMU driver, software events only. [ 0.011886] Brought up 1 CPUs [ 0.011998] Grant tables using version 2 layout. [ 0.012009] Grant table initialized [ 0.012034] NET: Registered protocol family 16 [ 0.012328] PCI: setting up Xen PCI frontend stub [ 0.015089] bio: create slab <bio-0> at 0 [ 0.015158] ACPI: Interpreter disabled. [ 0.015180] xen/balloon: Initialising balloon driver. [ 0.015180] xen-balloon: Initialising balloon driver. [ 0.015180] vgaarb: loaded [ 0.016126] SCSI subsystem initialized [ 0.016314] PCI: System does not support PCI [ 0.016320] PCI: System does not support PCI [ 0.016435] NetLabel: Initializing [ 0.016438] NetLabel: domain hash size = 128 [ 0.016440] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.016447] NetLabel: unlabeled traffic allowed by default [ 0.016475] Switching to clocksource xen [ 0.017434] pnp: PnP ACPI: disabled [ 0.017501] NET: Registered protocol family 2 [ 0.017864] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.019322] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.020376] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.020497] TCP: Hash tables configured (established 524288 bind 65536) [ 0.020500] TCP: reno registered [ 0.020525] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 0.020564] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 0.020624] NET: Registered protocol family 1 [ 0.020658] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.020662] software IO TLB [mem 0xfb632000-0xff631fff] (64MB) mapped at [ffff8800fb632000-ffff8800ff631fff] [ 0.020750] platform rtc_cmos: registered platform RTC device (no PNP device found) [ 0.021378] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.023378] msgmni has been set to 9656 [ 0.023544] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.023549] io scheduler noop registered [ 0.023551] io scheduler deadline registered [ 0.023580] io scheduler cfq registered (default) [ 0.023650] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.023845] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.024082] Non-volatile memory driver v1.3 [ 0.024085] Linux agpgart interface v0.103 [ 0.024207] Event-channel device installed. [ 0.024265] [drm] Initialized drm 1.1.0 20060810 [ 0.024268] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module! [ 0.025145] brd: module loaded [ 0.025565] loop: module loaded [ 0.045646] Initialising Xen virtual ethernet driver. [ 0.198264] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 0.199096] i8042: No controller found [ 0.199139] mousedev: PS/2 mouse device common for all mice [ 0.259303] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0 [ 0.259353] rtc_cmos: probe of rtc_cmos failed with error -38 [ 0.259440] md: raid1 personality registered for level 1 [ 0.259542] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 0.259732] ip_tables: (C) 2000-2006 Netfilter Core Team [ 0.259747] TCP: cubic registered [ 0.259886] NET: Registered protocol family 10 [ 0.260031] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 0.260070] sit: IPv6 over IPv4 tunneling driver [ 0.260194] NET: Registered protocol family 17 [ 0.260213] Bridge firewalling registered [ 5.360075] XENBUS: Waiting for devices to initialise: 25s...20s...15s...10s...5s...0s...235s...230s...225s...220s...215s...210s...205s...200s...195s...190s...185s...180s...175s...170s...165s...160s...155s...150s...145s...140s...135s...130s...125s...120s...115s...110s...105s...100s...95s...90s...85s...80s...75s...70s...65s...60s...55s...50s...45s...40s...35s...30s...25s...20s...15s...10s...5s...0s... [ 270.360180] XENBUS: Timeout connecting to device: device/vbd/51713 (local state 3, remote state 1) [ 270.360273] md: Waiting for all devices to be available before autodetect [ 270.360277] md: If you don't use raid, use raid=noautodetect [ 270.360388] md: Autodetecting RAID arrays. [ 270.360392] md: Scanned 0 and added 0 devices. [ 270.360394] md: autorun ... [ 270.360395] md: ... autorun DONE. [ 270.360431] VFS: Cannot open root device "xvda1" or unknown-block(0,0): error -6 [ 270.360435] Please append a correct "root=" boot option; here are the available partitions: [ 270.360440] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 270.360444] Pid: 1, comm: swapper/0 Not tainted 3.5.7-gentoo #1 [ 270.360446] Call Trace: [ 270.360454] [<ffffffff813d2205>] ? panic+0xbe/0x1c5 [ 270.360459] [<ffffffff813d2358>] ? printk+0x4c/0x51 [ 270.360464] [<ffffffff815d5fb7>] ? mount_block_root+0x24f/0x26d [ 270.360469] [<ffffffff815d62b6>] ? prepare_namespace+0x168/0x192 [ 270.360474] [<ffffffff815d5ca7>] ? kernel_init+0x1b0/0x1c2 [ 270.360477] [<ffffffff815d5500>] ? loglevel+0x34/0x34 [ 270.360482] [<ffffffff813d5a64>] ? kernel_thread_helper+0x4/0x10 [ 270.360486] [<ffffffff813d4038>] ? retint_restore_args+0x5/0x6 [ 270.360490] [<ffffffff813d5a60>] ? gs_change+0x13/0x13 The config: name = "dom1" bootloader = "/usr/bin/pygrub" root = "/dev/xvda1 ro" extra = "3" # runlevel memory = 5000 disk = [ 'phy:/dev/md1,xvda1,w' ] # vif = [ 'ip=..., vifname=veth1' ] # none for now Here are some details on the Dom0 kernel (grepping for "xen"): CONFIG_XEN=y CONFIG_XEN_DOM0=y CONFIG_XEN_PRIVILEGED_GUEST=y CONFIG_XEN_PVHVM=y CONFIG_XEN_MAX_DOMAIN_MEMORY=500 CONFIG_XEN_SAVE_RESTORE=y CONFIG_PCI_XEN=y CONFIG_XEN_PCIDEV_FRONTEND=y # CONFIG_XEN_BLKDEV_FRONTEND is not set CONFIG_XEN_BLKDEV_BACKEND=y # CONFIG_XEN_NETDEV_FRONTEND is not set CONFIG_XEN_NETDEV_BACKEND=y CONFIG_INPUT_XEN_KBDDEV_FRONTEND=y CONFIG_HVC_XEN=y CONFIG_HVC_XEN_FRONTEND=y # CONFIG_XEN_WDT is not set # CONFIG_XEN_FBDEV_FRONTEND is not set # Xen driver support CONFIG_XEN_BALLOON=y # CONFIG_XEN_SELFBALLOONING is not set CONFIG_XEN_SCRUB_PAGES=y CONFIG_XEN_DEV_EVTCHN=y CONFIG_XEN_BACKEND=y CONFIG_XENFS=y CONFIG_XEN_COMPAT_XENFS=y CONFIG_XEN_SYS_HYPERVISOR=y CONFIG_XEN_XENBUS_FRONTEND=y CONFIG_XEN_GNTDEV=m CONFIG_XEN_GRANT_DEV_ALLOC=m CONFIG_SWIOTLB_XEN=y CONFIG_XEN_TMEM=y CONFIG_XEN_PCIDEV_BACKEND=m CONFIG_XEN_PRIVCMD=y CONFIG_XEN_ACPI_PROCESSOR=m And the DomU kernel (grepping for "xen"): CONFIG_XEN=y CONFIG_XEN_DOM0=y CONFIG_XEN_PRIVILEGED_GUEST=y CONFIG_XEN_PVHVM=y CONFIG_XEN_MAX_DOMAIN_MEMORY=500 CONFIG_XEN_SAVE_RESTORE=y CONFIG_PCI_XEN=y CONFIG_XEN_PCIDEV_FRONTEND=y CONFIG_XEN_BLKDEV_FRONTEND=y CONFIG_XEN_NETDEV_FRONTEND=y CONFIG_INPUT_XEN_KBDDEV_FRONTEND=y CONFIG_HVC_XEN=y CONFIG_HVC_XEN_FRONTEND=y # CONFIG_XEN_WDT is not set # CONFIG_XEN_FBDEV_FRONTEND is not set # Xen driver support CONFIG_XEN_BALLOON=y # CONFIG_XEN_SELFBALLOONING is not set CONFIG_XEN_SCRUB_PAGES=y CONFIG_XEN_DEV_EVTCHN=y # CONFIG_XEN_BACKEND is not set CONFIG_XENFS=y CONFIG_XEN_COMPAT_XENFS=y CONFIG_XEN_SYS_HYPERVISOR=y CONFIG_XEN_XENBUS_FRONTEND=y CONFIG_XEN_GNTDEV=m CONFIG_XEN_GRANT_DEV_ALLOC=m CONFIG_SWIOTLB_XEN=y CONFIG_XEN_TMEM=y CONFIG_XEN_PRIVCMD=y CONFIG_XEN_ACPI_PROCESSOR=m Any ideas what I'm doing wrong here? Thanks a lot!

  Read the article

• Webcam security camera software that runs as a service

  - by hurfdurf

  I've been looking for Windows webcam software that will run as a Windows service without any user login. The goal is to use the webcam as a cheap security camera and log the results to secure networked storage (windows share, not FTP). The requirements are: Motion detection Video capture Runs as a service (should start recording immediately after reboot) Nice to have: Round-robin storage, e.g. 10Gb limit, oldest files overwritten/deleted when space gets low I've read the other webcam questions but still haven't stumbled across anything suitable. Evaluations thus far: Title MotionDetect Service Snapshots Video SpaceLimit License Yawcam Yes Yes Yes No No GPL WebCam ZoneTrigger Yes No Yes Yes No Commercial Dorgem Yes No Yes Yes No GPL AbelCam Yes No Yes Yes No Commercial Logitech Yes No Yes Yes No Paired with camera IspyConnect Yes No Yes Yes Yes Free SecureCam (SourcefoYes No Yes Yes No GPL AbelCam Yes No Yes Yes No Commercial Active WebCam Yes Yes(?) Yes Yes Volume Free Commercial WebCam Surveyor Yes No Yes Yes No Commercial WebCamsPy NA NA NA NA NA GPL Camera: Logitech Webcam Pro 9000 Windows 7 32-bit WebCamsPy failed to initialize so couldn't be tested So far, the contenders: Active Webcam comes the closest, and claims to run as a service, but i haven't been able to get it to record after a cold boot even though a service is running. Yawcam can be set up as a service but doesn't record video. IspyConnect has exactly the type of space limit I want and looks great, but doesn't run as a service (seems also to be a bit of a cpu hog) Any other suggestions? I'm locked into Windows so can't use linux Motion, which looks almost perfect. Any pointers to rich Windows webcam/motion detection libraries out there that could easily be turned into a command line program would also be appreciated.

  Read the article

• Hard Drive Compatibility with Motherboard

  - by Wesley

  Here are the current specs to put things in context: ECS P4VXASD2+ V5.0 Intel Pentium 4 Northwood 2.8 GHz 2x 512MB PC2100 DDR266 SDRAM Maxtor DiamondMax 10 250 GB PATA (IDE) HDD Gigabyte 52x CD-ROM NVIDIA TNT2 Pro 16 MB OKIA 300W ATX PSU USB bracket Modem PCI Before, I actually had a 300 GB hard drive installed. However, I read the FAQ for the motherboard and discovered that a maximum of 250 GB hard drive was supported. So I ended up finding the one listed above and put that in. However, upon booting up, I reset the BIOS to defaults and auto-detected all the drives installed. The 250 GB came up as something like 251.0 GB. I didn't think much about it until I tried to boot up a Windows XP installation disc. It booted up successfully and run for about a minute before the computer randomly rebooted. I've made sure that all the jumpers and settings are correct and everything has been installed correctly. I've tried running it without the addons and one stick of RAM but still the same thing. What else could be causing this problem?

  Read the article

• "could not find suitable fingerprints matched to available hardware" error

  - by Alex

  I have a thinkpad t61 with a UPEK fingerprint reader. I'm running ubuntu 9.10, with fprint installed. Everything works fine (I am able to swipe my fingerprint to authenticate any permission dialogues or "sudo" prompts successfully) except for actually logging onto my laptop when I boot up or end my session. I receive an error below the gnome login that says "Could not locate any suitable fingerprints matched to available hardware." What is causing this? here are the contents of /etc/pam.d/common-auth file # # /etc/pam.d/common-auth - authentication settings common to all services # # This file is included from other service-specific PAM config files, # and should contain a list of the authentication modules that define # the central authentication scheme for use on the system # (e.g., /etc/shadow, LDAP, Kerberos, etc.). The default is to use the # traditional Unix authentication mechanisms. # # As of pam 1.0.1-6, this file is managed by pam-auth-update by default. # To take advantage of this, it is recommended that you configure any # local modules either before or after the default block, and use # pam-auth-update to manage selection of other modules. See # pam-auth-update(8) for details. # here are the per-package modules (the "Primary" block) auth sufficient pam_fprint.so auth [success=1 default=ignore] pam_unix.so nullok_secure # here's the fallback if no module succeeds auth requisite pam_deny.so # prime the stack with a positive return value if there isn't one already; # this avoids us returning an error just because nothing sets a success code # since the modules above will each just jump around auth required pam_permit.so # and here are more per-package modules (the "Additional" block) auth optional pam_ecryptfs.so unwrap # end of pam-auth-update config #auth sufficient pam_fprint.so #auth required pam_unix.so nullok_secure

  Read the article

• Power Outage Interrupted Upgrade from Windows Vista Ultimate to 7 Ultimate, Reverted to Vista, Now Vista is failing... What Next?

  - by tednewk

  I was in the midst of what seemed to be a successful upgrade from Vista Ultimate to 7 Ultimate when there was a brief blackout. The upgrade failed and Windows reverted back to Vista. Now Vista is very slow to boot, has problems waking back-up from inactivity and quickly loses it's wireless connection. The wake-up problem manifests itself as the mouse is clearly shown on a black screen but I have no access to the Desktop or Taskbar or Explorer. Even Alt-Ctrl-Delete doesn't seem to work. No task menu, no reboot. Hitting the reset button reboots the machine with the usual Black Screen warnings offering Safe Mode. I tried to do a system restore to a point before the upgrade. That didn't seem to work. My guess is that my system is a mutant with parts of Vista and parts of 7 crashing each other. I would like avoid a clean install if at all possible to avoid reinstalling other software. What should I try now? My thoughts are: My a system back-up to lock the computer in place Trying a second 7 upgrade If that appears to be working make another back-up If not reload back-up and try a repairing Vista from DVD. If that appears to work make another back-up, let system stablize about a week then try 7 install again If that doesn't work are there any other options to try before settling for a clean install? Another complication, I am doing this by "remote control". I'm traveling with my job and I'll be talking my son through it over the phone. (Kind of like the landing the 747 cliche from all the 70's adventure shows!) So is there a way of simplifying the steps? Thanks Ted

  Read the article

• Snow Leopard takes a long time to connect to Windows/Samba server

  - by hood

  We run a very heterogeneous network here: There is some XP, Vista, 7, Leopard, Snow Leopard clients, and Windows 2003 (one remaining legacy app), 2008, and Linux servers. The main file server runs Ubuntu Linux and has been added to the Windows Domain and has been used for many years; SBS 2008 is the PDC (the 2003 and 2008 are on the domain also). In Leopard there were no problems at all authenticating to the file servers. We've upgraded one of the Leopard iMacs to Snow Leopard, though the same problem occurs in a new MBP which came with the newer OS as well as a clean install on another iMac. It does not matter whether connected through wired or wireless. In the Finder when clicking on the server - whether on first boot or after it is connected - it will display "Connecting..." for up to a few minutes before either generally working (if username/password in keychain) or displaying "Connection Failed" - at which time clicking "Connect As" and typing in the username/password will take some more time and eventually work. Sometimes it will display "Connecting..." indefinitely. (I've left it as long as 15 minutes before trying something else) Accessing shares on the the 2003 and SBS servers have the problem (so I don't think it's a Samba server issue). The Server 2008 Standard is connecting instantly at the moment. Accessing the share through an alias/stacks doesn't have this problem. Leopard and Windows clients still have no problem. I've searched Google but hasn't yielded any working result. How do I get rid of this delay?

  Read the article

• CentOS Installation on a Cisco MCS 7800

  - by William

  Hello, I'm having some problems installing CentOS 5.5 Final (i386) Onto my server, a Cisco MCS 7800. The problem comes very early into the installation. When the welcome screen comes up ans gives you the option on how to boot into the DVD, Ill press enter to go into the graphical installer. The Screen will then have a blinking cursor in the top left of the screen and will never go away (I thought that it just might need time but I let it sit for over 5 hours.) I then booted into it again and tried using Linux Text thinking it was a problem with graphical installer. That didn't work, same problem. Then I tried a DVD of RHEL 5 and got the same problem, both graphical and Linux text. At this point i think its a hardware problem. The Server has 2GB of ECC RAM, 1 Pentium 4 CPU @ 3.06GHZ and 2 WD Hard Drives (80GB) Configured for RAID 0. ( Also there is a option in the BIOS for what OS type and that is set to Linux.) If anyone has any idea what is going on, it would be helpful. ================Edit================== ooshro, typing "text" doesn't change a thing. still stuck at the blinking cursor. I looked it up and its really the same thing as typing "linux text", which as stated in the first part of my question, i've already done.

  Read the article

• How to disable monitor "sleep" on Ubuntu without access to X?

  - by exhuma

  I just received a CuBox (basically a tiny ARM based PC). It comes pre-installed with Ubuntu, and I did not (yet) want to fiddle with the OS itself. My aim is to have it automaticall start a browser in fullscrren upon boot. Using chromium with the "--kiosk" flag works perfectly in that regard. But now I have the problem that the screen turns off after a certain time. I managed to turn off the screen saver using: gconftool-2 -s /apps/gnome-screensaver/idle_activation_enabled --type=bool false And tried to turn off the power management using: gconftool-2 -s /apps/gnome-power-manager/ac_sleep_display --type=int 0 and gconftool-2 -s /apps/gnome-power-manager/timeout/sleep_display_ac --type=int 0 Neither of the power-management commands worked. Theoretically I could hook up a mouse and keyboard and configure it manually. But I want to learn how to do it over the console. The box will eventually be only reachable via SSH. So I'd like to be able to trouble-shoot it later. I don't quite know where to look for. I searched the gconf tree using gconftool-2 -S for anything related to the terms power, idle and sleep but did not find anything promising. Maybe it's not even gconf related... Any ideas what else I could look for?

  Read the article

• Windows 7 hangs on black screen for a while after log in

  - by steini

  I get the welcome screen. I click on my user and get the "logging on" screen. After that all I get is a black screen with a mouse cursor. I can't even start task manager. No ctrl+alt+del or ctrl+shift+escape. It stays like this for about 10 minutes, then the desktop finally starts loading. According to the hdd led on my case, windows isn't even trying to access the hard drive for that whole time. It's just hanging doing nothing it seems. What I have tried: Uninstalled video driver and removed leftovers with driver sweeper Disabled all startup programs and non microsoft services Loaded "last known good configuration" Ran the alleged "black screen fix" from prevx against my best judgement (don't really like running random exes without knowing what they do at all) None of that works. I can boot into safe mode normally. My specs: i7 920 Gigabyte X58-UD3R Gigabyte HD5870 1GB 12GB Mushkin Silverline 1333MHz Windows 7 Ultimate x64 I'm also having another problem which I suspect is related. After I have gotten the computer up and running, everything works perfectly, but when it's been on for a while it starts behaving strangely when changing display modes. When I start up a game or anything that changes the screen resolution the computer freezes for about a minute every time until I reboot again. I think this is probably related to the black screen problem. Just thought I'd check to see if anyone has had the same problem. Let me know if I should post any more details about my system to help diagnose this. Thanks in advance.

  Read the article

• Failover Cluster Quorum Failing

  - by oruchreis

  Hi, I have two nodes which boots from iscsi to implement windows 2008 cluster. And I'm using disk majority option as quorum over iscsi. But when the quorum's iscsi connection failed(May be san server reset), the failover cluster is failed too. If I reset one of the nodes, it can open, but its system disk goes offline. I cant change its status as online, because it says that its reserved by failover cluster(disk is on iscsi, beacuse iscsi boot). And this disk works as readonly. Anything on it cant be deleted or written. So, I cant rejoin the node to the cluster again. I have to reinstall windows. So, what I'm asking is, how can I implement more quorum backup? I mean, can I use both disk majority and file share majority at same time? AFAIK, every nodes also keep the quorum's copy too. But I don't know sometimes san servers goes offline. And quorum's iscsi connection and nodes' iscsi connections get lost. So, nor the quorum that is kept in the nodes neither the quorum iscsi disk is not enough to start the cluster again. I want to use both disk majority and file share majority at the same time. Can I do this? Have you any other suggestion? Regards.

  Read the article

• Explorer.exe hangup during move large file into external drive

  - by PiotrK

  During move large files (700mb+) to external drive formated NTFS via USB 3.0 I've noticed strange things about explorer.exe (I am using Windows 7 up to date) Sometimes after move file the explorer get stuck (ie. it can happen after few files during move of several large files) - moving window freeze and I am unable to kill explorer (via taskmgr, or cmdline TASKKILL). In command line I've got something like this (taskmgr shows that explorer.exe is still running - I've got the same PID every time I try to kill it and no diagnostic message): C:\Windows\system32TASKKILL /F /IM explorer.exe SUKCES: proces "explorer.exe" o identyfikatorze PID 6296 zostal zakonczony. C:\Windows\system32TASKKILL /F /IM explorer.exe SUKCES: proces "explorer.exe" o identyfikatorze PID 6296 zostal zakonczony. If I try to run another explorer.exe process at this point, I got desktop icon and start bar back but I cannot open any explorer window After few minutes explorer.exe finally dies and I am able to rerun it without rebooting File that I moved have two copies - one local and one on the external drive (the original file wasn't delete after move); Both copies seems to contain the same data (same length and CRC info) If this happen during move of multiply files, only some files are moved and one of them have two copies (both locally and on the external drive) What can I do to fix those explorer hangs? Added: The same problem exist when copying files, it hangsup between large files Similar problem exist when I tried to use TotalCommander (x64): copying paused at 80% of one of files, TC didn't hung up (but clicking cancel in copying dialog box doesn't have any effect). During this pause I can't kill TotalCmd.exe just like Explorer.exe Added (2): This problem seems to disappear when I use 32 bit applications (like TotalCommander (x86) ), but I need to do more testing to be sure of this Added (3): There are several errors in event log, source: disk, id: 11, qualifiers: 49156, task: 0, level: 2, keywords: 0x80000000000000 (This may be important, and I forgot to mention this): Main disk is encrypted via Truecrypt (boot-in password)

  Read the article

• IBM BladeCenter S: Disk Configuration

  - by gravyface

  Have just the one storage bay right now (SAS 15K 600GB x 6) and have configured one storage pool in RAID 10 with 4 disks (and two global spares). For each blade, I've created a volume and mapped accordingly: Blade #1 400 GB Blade #2 200 GB Blade #3 100 GB Blade #4 100 GB When I boot up Blade 1 and enter into the UEFI Setup (F1) followed by the Adapters and UEFI Drivers LSI Logic Fusion MPT SAS Driver Utility, I see 4 disks: two are the on-board 73GB drives, the other two are 200GB each and assume I'm being presented with two logical disks from the volume I created and mapped to this blade. I was a bit surprised by this: I figured I would've been presented with one logical drive per volume, not two. I'm assuming I can just configure whatever RAID level I wish that supports two disks, but not really sure what the benefits/trade-offs here. Should I go with RAID 10 on top of RAID 10? RAID 0? Software RAID 0/1/10? Does it even matter? If this is "normal" to see two disks, then I'm going to likely just do some benchmarking and see if it makes a difference changing the RAID levels (my guess is no); if this is not normal, well, please let me know. :)

  Read the article

• Aging SBS needs updates / Thoughts for one-off, off-line complete backup?

  - by tcv

  Hey guys, So, we checked out the status of an SBS 2003 at one of our more recent, spend-averse clients and found it to be woefully out-of-date. Scary out of date. I think it's running IE2. Ok, maybe not that far back. Anyway, I was thinking that I could use some kind of disk-imaging software to image the four IDE drives within and, in the event the server gets some kind of Update Induced Indigestion, I could completely restore. Usually my go-to software for this is Acronis, but my client will likely balk at a $500 price tag for a one-off backup with their server product. I had thought we could use the boot media from, say, Backup & Recovery 10 to take an off-line image of all the drives. According to their CHAT tech support, however, it will not work. I pressed for the technical reasons and they said they'd email me. They haven't emailed me. They still might. This server is running SBS 2003, pre sp2. It's got four IDE disks. One is a Basic disk, which contains the O/S. The others are bound as a dynamic disk. You might ask: "Don't they already have backup software?" They do! Backup Exec, a very low-end version that won't even do VSS. I don't know much about BE, but it seems to me that if the worst were to happen, it would mean building a new server O/S, installing BE (if the media is available), then restoring. Would it even work? I can take the system down for hours to do a backup and my goal here is a pretty dead-simple restore if the worst happens. Any and all suggestions are exciting. m

  Read the article

• VMWare Workstation 8 Disk I/O & Hard Faults

  - by Scott

  I have VMWare Workstation 8 installed on a host machine with the following specs: Intel i5 2500k CPU 16GB DDR3 1600 ram 1TB Western Digital Caviar Black HD I have two Windows 7 virtual machines configured (currently running one at a time but will be operating both at once when my 32GB RAM kit arrives in a couple days). Each one is configured with 8GB of RAM and no tweaks/performance customizations or anything done. All of the VMWare settings are the defaults. When I boot into these machines and run various programs (Visual Studio, Outlook, etc), I can hear the disk thrashing quite a bit and checking Resource Monitor, I can see that I'm getting anywhere between 300-800 hard faults per second. From the host machine, it shows they're coming from the VMWare image. If I go to the virtual machine, whatever app I'm currently loading is the image that's causing the hard faults. As I understand it, hard faults are (simply) when an address in memory has been swapped out to the page file and has to be read from the page file instead of from memory. I don't understand why this is happening though. With 8GB of ram on the guest machine and 6.5GB available, what could be causing this? I know Windows 7 supposedly improved on page file management over XP but it seems excessive for this kind of slowdown, disk thrashing and high hard fault count when I have that much free RAM. Is there anything I can to to improve the performance in my guest machines? On the host machine, I can open/run any applications at all and hard faults stays around 0 with low disk I/O.

  Read the article

• SSD as primary or secondary drive on a small Linux server?

  - by Alex Martelli

  I'm pensioning off my 10-years-old home server and replacing it with an Ubuntu 10.04 box. The two storage devices are a Western Digital Caviar Green 2.0TB HD and an Intel X25-M 34nm Gen 2 80GB SATA II 2.5inch SSD (the box has 8GB RAM and an i5 750, if it matters). I don't care much about boot times (since I don't plan to reboot all that often;-); the main frequent, performance-demanding task will be (re)building large open source C or C++ software packages from sources (as an open source contributor, I do that often). So, I thought I'd keep the SSD as the secondary drive and the HD as the primary one, using the SSD mostly for the files that can otherwise demand a lot of seeking (esp. in a parallel make). However, the friendly vendor (perhaps more experienced in Windows systems than in Linux ones) thinks the "normal" way to configure the machine would be with the SSD as the primary drive. I'm pretty rusty on configuring and tuning systems, so, I thought I'd better double check on SuperUser... thanks in advance for advice about this choice!

  Read the article

• Computer hangs at BIOS screen. Cannot enter setup

  - by d2jxp

  I have an HP Pavilion a6500f (it's a year out of warranty) and it's hanging on the blue HP BIOS screen. If I mash F10 while it's starting up, it will say "Entering Setup..." but I will see no results. It will hang there and not do anything. If I actually wait until I can see the screen and then hit F10, there's no response at all and the computer will sit at the BIOS menu. I've dusted and cleaned it out, reseated the memory, switched the RAM slots, and reset the CMOS battery using the reset jumper. I'm out of ideas. I'm pretty sure it's not a hard drive issue, since my problem is at the BIOS. After this post, I'll disconnect the hard drive and try to just boot without it. Anyone have any other ideas? Edit: Okay, so I tried disconnecting the hard drive and now I can get back into the BIOS. I reconnected it and I'm locked out again. So the problem is my hard drive.. I guess I should delete this post unless someone has any ideas as to what's wrong with the drive?

  Read the article

• Snapshotting single disk of running Hyper-V VM

  - by modelnine

  I'm currently somewhat at a loss of how to create a snapshot of a single virtual hard-disk of a running Hyper-V VM. Generally, creating a differential disk while a server is shut down is no problem (i.e., call the new-vhd cmdlet and pass a ParentPath, then update the VHD-binding of the respective VM-device), but while the host is running, all I can find is checkpointing the VM as a whole (which creates snapshots of all attached disks), and leaves the VM-state in a form which isn't easily processable by external tools (i.e., it requires reading additional meta-data from the VM). Generally, what'd I'd like to happen for a single-disk snapshot (in my understanding) is: Pause the VM Rename current disk to some other name which specifies it as a base-snapshot Create a new VHD which has the renamed VHD as parent path and is marked as "current" Swap the VHD for the VM for the snapshotted hard-disk to the newly created differential VHD Resume the VM Is there any means to do this programatically? Update: I've seen that this is actually possible with SCSI-disks, i.e. pause the VM, remove the SCSI disk, make the snapshot, reattach the SCSI disk at the same position, resume the VM. And, the VM resumes properly. But: is something similar also possible with G1 machines for the boot disk which is always IDE?

  Read the article

• MAMP Pro mysqld won't start on os x lion

  - by Mike

  getting a Start MySQL Failed error in the GUI.. when i attempt to start mysqld from the CLI i get the following error: ? /Applications/MAMP/Library/bin/mysqld 120623 23:12:47 [Warning] Setting lower_case_table_names=2 because file system for /Applications/MAMP/db/mysql/ is case insensitive 120623 23:12:47 [Note] Plugin 'FEDERATED' is disabled. 120623 23:12:47 InnoDB: The InnoDB memory heap is disabled 120623 23:12:47 InnoDB: Mutexes and rw_locks use GCC atomic builtins 120623 23:12:47 InnoDB: Compressed tables use zlib 1.2.3 120623 23:12:47 InnoDB: Initializing buffer pool, size = 128.0M 120623 23:12:47 InnoDB: Completed initialization of buffer pool 120623 23:12:47 InnoDB: highest supported file format is Barracuda. 120623 23:12:47 InnoDB: Waiting for the background threads to start 120623 23:12:48 InnoDB: 1.1.5 started; log sequence number 1595675 120623 23:12:48 [ERROR] /Applications/MAMP/Library/bin/mysqld: unknown option '--skip-locking' 120623 23:12:48 [ERROR] Aborting 120623 23:12:48 InnoDB: Starting shutdown... 120623 23:12:49 InnoDB: Shutdown completed; log sequence number 1595675 120623 23:12:49 [Note] /Applications/MAMP/Library/bin/mysqld: Shutdown complete i have deleted the mysql.pid file located at /application/mamp/tmp/mysql/mysql.pid and i still get the error above. I can't find where MAMP has set --skip-locking set, my.cnf doesnt have it anywhere. Activity monitor gives me a mysqld process running by me, and everytime i KILL the process both via Activity Monitor and via kill =9 pid it starts right back up.. Sampling the process points back to the MAMP mysqld.. wtf?! About to throw MAMP out the window and boot up a VM of CentOS =)

  Read the article

• nginx not starting at reboot after gitlab installation

  - by Luis Masuelli

  I installed nginx (1.6) in ubuntu server (14.04). After that, I installed gitlab. I didn't realize it came with its own nginx. I uninstalled gitlab later. After installing gitlab, my first nginx began to never start at boot as a service. This means: If I hit sudo netstat -anp I don't see the corresponding entry in 0.0.0.0:80. If I hit sudo nginx -s reload and then sudo netstat -anp I see the corresponding entry I mentioned. I thought I could fixing it by doing: sudo update-rc.d nginx remove sudo update-rc.d nginx defaults After removing gitlab, but it did not help me (i.e. after reboot, nginx does not automatically start). I revised the /etc/init.d/nginx just to see that $DAEMON is still /usr/sbin/nginx. Question: What should I check to see the problem here (or: what could the problem be)? sudo nginx -s reload works with no problems at all.

  Read the article

• My home router randomly disconnects me and I'm unable to reconnect to it

  - by Roy Tang

  It's happened a few times, I'm not sure how to diagnose/debug, so any advise would be appreciated. Symptons: sometimes the router will randomly disconnect; the connection icon on my desktop (wired to the router) gets that yellow "!" symbol that tells me my connection just went down. At this point I'm unable to ping the router. afterwards I try to reset the router by removing then reconnecting the power jack on the router side (this is the fastest way as I can't reset the power strip it's connected to without rebooting my desktop. the router has a reset thingy, but it's one of those things where i have to find a pin to stick into the hole, and when I get disconnected I usually need to get reconnected immediately so I just pull and put back the power jack), but even after that the connection has the same state. after the router reboots, if I try to connect to it using a wifi device like my ipad, the ipad prompts me for the wifi password even though it had already "remembered" all the settings for this router forever after i finally decide to reboot the power strip, and my desktop and the router boot up again, the connection returns to its normal state somewhat and i'm able to connect to it as normal using the desktop and wifi devices. What do I need to check the next time this happens so I can figure out the problem? Is it possibly because we've been using the power jack on the router as an easier way to reboot it? Should I be shopping around for a new router? If it helps, the router is a DLink DIR-300

  Read the article

• Replacing HD in an MacOS 10.6.8 server caused all shares to fail

  - by Cheesus

  I'm hoping someone might have a helpful suggestion about this problem. We have 2 MacOSX servers available for file sharing. (quad Xeons - 2GB RAM, both 10.6.8), No.1 is an Open Directory Master with 50+ user accounts, No.2 has only 2 local accounts (/local/Default) and looks at the OD Master for all user accounts (/LDAPv3/10.x.x.20/) Both servers have 3 internal HD's, The boot volume with only Server OS and minimal Apps. A 'DataShare' HD (500GB) and a backup drive (500GB). After upgrading the DataShare HD in Server No.2 from a small internal HD (500GB) to larger capacity (2TB) drive, users are unable to connect to shares on Server No.2. Users get an error "There are no shares available or you are not allowed to access them on the server" The process I followed was to use Carbon Copy Cloner to create an exact copy of the original data drive (keeps all ownership data, UID, permissions, last edit date and time). Everything booted up ok, no indication there was any issues. (Paths to the sharepoint look good) Notes during troubleshooting - Server1 is operating perfectly, all users can access shares and authenticate etc. - I've checked the SACL (Server Access Control List) settings is ok. - On Server2 in the Server Admin' app, I can see all the shares listed ok. The paths seem valid, I can disable / reenable the shares, no errors. - On Server2 'workgroup manager' lists all the accounts from the OD Master in the LDAP dir view. All seems fine from here. Basically everything looks normal but no file shares on Server2 can be accessed from regular users.

  Read the article

• Display issue with fresh install of windows server 2012

  - by Tony

  I installed windows server 2012 last night on my home "server". I use server loosely. From the get go I had display and graphic issues. The image was fuzzy and jumbled up during the install. This continued once booted into the install. I did installed Server 2012 twice now as the first time, I only installed "core". I know this is not a busted graphics card because it worked fine in Win7, during boot, and fine in "core" mode. Once booted into "GUI" install of Server 2012, the image was messed up again. To make things even more weird, the windows "loading" screen looks fine. Once the login screen appears the image is fuzzy and jumbled. My guess was that it was a driver issue. I did try to install the win8 x64 drivers from nvidia. This caused the system to become unbootable and I had to restore to a previous working point and uninstall the driver. I did try two different monitors and cables. Also both ports on the back of the video card. I did manage to get RDP running and that works fine. I rarely work directly on this machine but it would be nice to have the option back. Geforce 210, AMD 4600+, 4 gigs of ram.

  Read the article

• Linux will not activate wireless after device has been re-enabled

  - by XHR

  Using a Eee 900A netbook by Asus. By pressing Fn + F2, I can disable or enable the wireless chip on the netbook, a blue LED indicates the status. I've been able to connect to wireless networks just fine with this netbook. However, if the wireless chip ever becomes disabled, I have to reboot to get my network connection back. This generally happens when suspending. For some reason the LED will be off and I have to hit Fn + F2 for it to light up again. However, after doing so, Linux will not reconnect to the network. It simply changes the wireless status from "wireless is disabled" to "device not ready". Even worse, I've recently had issues with the chip being enabled at boot, thus making it nearly impossible to get connected. I've searched around on-line but haven't found much of anything useful on this. This happens on all kinds of different distros including Ubuntu 9.10 Netbook, EeeBuntu 4 beta, Jolicloud and Ubuntu 10.04 Netbook. Edit I noticed this question is getting a lot of views. To give a quick update, I never did resolve this issue with the given distro's. However, I'm currently running Ubuntu 10.10 netbook edition and this issue has gone away.

  Read the article

• What user information is exposed via a browser?

  - by ipso

  Is there a function or website that can collect and display ALL of the user information that can be obtained via a browser? Background: This of course does not account for the significant cross-reference abilities of large corporations to collate multiple sources and signals from users across various properties, but it's a first step. Ghostery is just a great idea; to show people all of the surreptitious scripts that run on any given website. But what information is available – what is the total set of values stored – that those scripts can collect from? If you login to a search engine and stay logged in but leave their tab, is that company still collecting your webpage viewing and activity from other tabs? Can past or future inputs to pages be captured – say comments on another website? What types of activities are stored as variables in the browser app that can be collected? This is surely a highly complex question, given to countless user scenarios – but my whole point is to be able to cut through all that – and just show the total set of data available at any given point in time. Then you can A/B test and see what is available with in a fresh session with one tab open vs. the same webpage but with 12 tabs open, and a full day of history to boot. (Latest Firefox & Chrome – on Win7, Win8 or Mint13 – although I'd like to think that won't make too much of a difference. Make assumptions. Simple is better.)

  Read the article

• Liked Arch Linux - but I am still not sure if its the right distro for me...

  - by BlackAndGold

  As the title says... I used Arch Linux for a while and liked it a lot: leightweight, sleek, fast and well documented with a great community. However I had to format my hd and for the sake of being too lazy to reinstall arch, I used windows 7 exclusively for a while. Now I want to get back to linux again (still dual boot), mainly for web development purposes and using handy tools such as rsync ect. Again, I liked Arch, but there is too much tweeking, too much reading up and too much figuring out what to do as well es some bad suprises especially when you need them the least and when just quickly want to get some work done. I kind of would like to have a little more "out of the box" distro that is still fast and somewhat leighweight and of course reliable. I actually considered Ubuntu, which I am not too big of a fan of, but I will still give the minimal install a shot. However other distros seem interesting as well, such as crunchbang and mint debian ecpecially. My question, hoping this isn't too boring for many you, what is the right distro for me?

  Read the article

< Previous Page | 403 404 405 406 407 408 409 410 411 412 413 414  | Next Page >