Search Results

Search found 44026 results on 1762 pages for 'raid question'.

Page 407/1762 | < Previous Page | 403 404 405 406 407 408 409 410 411 412 413 414  | Next Page >

  • iptables -- OK, **now** am I doing it right?

    - by Agvorth
    This is a follow up to a previous question where I asked whether my iptables config is correct. CentOS 5.3 system. Intended result: block everything except ping, ssh, Apache, and SSL. Based on xenoterracide's advice and the other responses to the question (thanks guys), I created this script: # Establish a clean slate iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT iptables -F # Flush all rules iptables -X # Delete all chains # Disable routing. Drop packets if they reach the end of the chain. iptables -P FORWARD DROP # Drop all packets with a bad state iptables -A INPUT -m state --state INVALID -j DROP # Accept any packets that have something to do with ones we've sent on outbound iptables -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT # Accept any packets coming or going on localhost (this can be very important) iptables -A INPUT -i lo -j ACCEPT # Accept ICMP iptables -A INPUT -p icmp -j ACCEPT # Allow ssh iptables -A INPUT -p tcp --dport 22 -j ACCEPT # Allow httpd iptables -A INPUT -p tcp --dport 80 -j ACCEPT # Allow SSL iptables -A INPUT -p tcp --dport 443 -j ACCEPT # Block all other traffic iptables -A INPUT -j DROP Now when I list the rules I get... # iptables -L -v Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 0 0 DROP all -- any any anywhere anywhere state INVALID 9 612 ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- lo any anywhere anywhere 0 0 ACCEPT icmp -- any any anywhere anywhere 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:ssh 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:http 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:https 0 0 DROP all -- any any anywhere anywhere Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 5 packets, 644 bytes) pkts bytes target prot opt in out source destination I ran it and I can still log in, so that's good. Anyone notice anything major out of wack?

    Read the article

  • I want my logs sent to my mail with logrotate

    - by lericson
    Not strictly a question about programming as such, more of a log handling question. Anyway. My company has multiple clients, and each of these clients have a set of logs that I'd rather much want to get sent to by e-mail to me. Now, another prerequisite is that they're hilighted by simple HTML. All that is very well, I've managed to make a hilighter for the given log types. So, what I do is I use logrotate's prerotate stuff to send the logs as an e-mail message. Example: /var/log/a.log /var/log/b.log { daily missingok copytruncate prerotate /usr/bin/python /home/foo/hilight_logs /var/log/{a,b}.log | /usr/sbin/sendmail -FLog\ mailer [email protected] [email protected] endscript } The problem with this approach is basically that logrotate sucks: it'll run the command for every log file specified in the specifier, and to my knowledge there's no way to know which of the log files is being handled. (Which wouldn't really help anyway.) Short of repeating the exact same logrotate up to 10 times on different machines, the only thing I can do is just to get bogged down with log spam every night. And I grew tired of it today, so I ask.

    Read the article

  • "Can't find root filesystem / error mounting /dev/root" when booting to new kernel

    - by salparadise
    I am trying to upgrade my kernel from 2.6.18-274 to 2.6.39 for some wireless card drivers. When I boot into the new kernel I get the "Can't find root filesystem / error mounting /dev/root" googling led me to this page http://fedoraproject.org/wiki/Common_kernel_problems#Can.27t_find_root_filesystem_.2F_error_mounting_.2Fdev.2Froot From what I am reading seems to be an issue with a driver for my SATA controller or HD, but I can't find what option I need to add to the kernel. Doing a diff from the old initrd to the new one gives me the following: root-> diff /tmp/kafter /tmp/kbefore 6a7,8 > lib/dm-message.ko > lib/dm-region_hash.ko 8a11 > lib/dm-raid45.ko 13d15 < lib/dm-region-hash.ko 16a19 > lib/dm-mem-cache.ko Do I need any of those? not sure if I would need dm-raid45.ko as I am not running a raid. I have the same SATA and IDE options configured for both kernels so not sure what else to look for, any help is appreciated. Additionally here is the HW info: 00:1f.2 IDE interface: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA Controller (rev 03) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Hewlett-Packard Company Unknown device 3006 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 233 I/O ports at 1818 [size=8] I/O ports at 1830 [size=4] I/O ports at 1820 [size=8] I/O ports at 1834 [size=4] I/O ports at 14f0 [size=16] Capabilities: [70] Power Management version 2 root-> smartctl -a /dev/sda ... === START OF INFORMATION SECTION === Device Model: WDC WD5000AADS-00S9B0

    Read the article

  • What to look for in a switch with LAN/WAN verses an iSCSI SAN?

    - by Luke
    I'm setting up a VMWare ESXi 5 environment with 3 server nodes. Dell recommended 2x Force10 S60 switches shared (iSCSI SAN, LAN/WAN). The S60 switches are extremely powerful. They have 1.25 GB of buffer cache, < 9us latency. But they are very expensive (online price ~$15k per switch, actual quote a little less). I've been told that "by the book" you should at least have 2 internal switches for SAN, and 2 switches for LAN/WAN (each with a redundant). I know some of the pros and cons of each approach. What I'm wondering is, would it be more cost effective to disjoin the SAN from LAN with less expensive switches? The answer to this question highlights what I should be looking for in a switch for the SAN. What should I be looking for in a LAN/WAN switch, in comparison to the SAN? With the above linked question for the SAN: How is buffer latency measured? When you see 36 MB of buffer cache, is that shared or per port? So 36 MB would be 768kb or 36MB per port? With 3 to 6 servers how much buffer cache do you really need? What else should I be looking at? Our application will be heavily using HTML5 websockets (high number of persistent connections). The amount of data being sent is small; Data sent between client <- server isn't broadcasted (not a chat/IM service). We will be doing some database reporting too (csv export, sums, some joins). We are a small business and on a budget. We'd probably only be able to spend no more than $20k on switches total (2 or 4).

    Read the article

  • VirtualBox: using physical partition as virtual drive

    - by Hamman Samuel
    Background: I am using VirtualBox installed on Windows 7. From within VirtualBox I am using Xubuntu as a virtual OS. The reason I chose this approach is so that I don't have to keep turning off Windows and rebooting from Xubuntu every time I needed to switch OSes. And VirtualBox's seamless mode is pretty amazing to allow me see Xubuntu and Windows 7 all in one screen. Issue: Now I am thinking of a way to have Xubuntu more integrated into my system. By this I mean I want to have a physical partition for Xubuntu. But I want to still have the feeling of the seamless mode. Question: So finally, my question is: is it possible to load a partition in VirtualBox as a virtual OS? Case examples: Ideal scenario would be: I physically boot up and login to Windows 7. Now I want to access Xubuntu, so I load VirtualBox and access my Xubuntu partition without rebooting. And the other way around too, i.e. I boot up the system, login to Xubuntu, and can access the actual Windows 7 partition through VirtualBox. Other info: Please note that I am not talking about getting access to files, as I have a completely separate partition for my files, and am very familiar with VirtualBox's Shared Folders option.

    Read the article

  • Win2008: Boot from mirrored dynamic disk fails!

    - by Daniel Marschall
    Hello. I am using Windows Server 2008 R2 Datacenter and I got two 1.5TB S-ATA2 hard disks installed and I want to make a soft raid. (I do know the disadvantages of softraid vs. hardraid) I have following partitions on Disk 0: (1) Microsoft Reserved 100 MB (dynamic), created during setup (2) System Partition 100 GB (dynamic) (3) Data partition, 1.2TB (dynamic) I already mirrored these contents to Disk 1. Its contents are: (1) System partition mirror, 100 GB (dynamic) (2) Data partition, 1.2 TB mirror (dynamic) (3) Unusued 100 MB (dynamic) -- is from "MSR" of Disk 0, created during setup. Since data and system partition are mirrored, I expect that my system works if disk 0 would fail. But it doesn't. If I force booting on disk 0: Works (I get the 2 bootloader screen) If I force booting on disk 1 (F8 for BBS), nothing happens. I got a blank black screen with the blinking caret. I already made disk1/partition1 active with diskpart, but it still does not boot from this drive. Please help. Both partitions are in "MBR" partition style. They look equal, except the missing "MSR" partition at the partition beginning (which seems to be not relevant to booting). Regards Daniel Marschall

    Read the article

  • KVM Hosting: How to efficiently replicate guests

    - by javano
    I have three KVM servers each with 1 guest VM, running directly on it's local storage, (so they are essentially getting a dedicated box worth of computing power each). In the event of a host failure I would like the guests replicated to at least one of the other hosts so I can spin it up there, until the failing host is fixed. I am curious about KVM cloning. I can clone a VM live or when it's suspended/shutdown. Obivously suspended VMs will naturally be quicker to clone but these three VMs comprise three parts of a single solution, so I don't want to ever have any one of them shutdown. How can I efficiently clone these VMs between servers? I have had a couple of ideas, but are these insane or, is there a better method I have missed for my scenario? Set up a DRDB partition between box 1 and 2 where VM 1 runs from, and so is replicated between box1 and box 2, repeat between box 2 & 3, and box 3 & 1 (This could be insane, I have never used DRDB only read about it) Just use standard KVM CLI clone options to perform live clones (I'm dubious about this because I don't know how long it will take and what the performance impact will be during) Run a copy of each VM on at least one other host, and have the guest on one host export it's data to the matching guest on another host where it can import that data, scripting this on the guest) Some of other way? Ideas welcome! Side Note These servers have 4x15k SAS drives in a RAID 10 so they aren't rocketing fast, and as I mentioned, each VM runs from the host's local storage, no NAS or SAN etc. So that is why I am asking this question about guest replication. Also, this isn't about disaster recovery. Guests will be exporting their data to a NAS over a VPN, so I am looking at how I can have them quickly spun up in a host failure situation.

    Read the article

  • Disk wipe preferences

    - by hmvm123
    I manage a pool of systems that are loaded with software and sent to potential customers for evaluations which often land sensitive information on the drives. Before shipping them back, they typically like a standard wipe to be run to clean out the drives. Most are familiar with DBAN so I try to make sure it can work on my systems. Unfortunately, this means I'm usually in RAID driver hell trying to make sure that the versions out there support the ones my systems are shipping with. These are various kinds of 3ware and LSI ones. Consequently, I have DBAN 1.0.7 working on some, a beta version of 2.0 on the others and 2.2.6 on some of the latest SSD based ones. Now with the LSI controllers on my IBM x3550 M3s (1064/1068) I'm getting no love at all. Is there a way out? Do you buildroot with DBAN and try to piece the drivers together? Any other tools, free or commerical, that stay updated. I'm trying to walk people of varying technical proficiencies through this, so a boot disk with simple choices is preferable.

    Read the article

  • Mounted HDD not having enough permissions from Apache/PHP

    - by Dan
    Piwigo gallery, on apache and php, CentOS 6. The root system is a RAID 128GB. /var/www/html is on the root file system. Mounted the 320GB hdd to /var/www/html/320 using defaults, it's an ext4 fs. Put a symlink to it in /var/www/html/galleries which is read by the gallery script so I can upload images to there, then click sync. It gives me the error: [./galleries/] PWG-ERROR-NO-FS (File/directory read error) PWG-ERROR-NO-FS: The file or directory cannot be accessed (either it does not exist or the access is denied) chmod 777 set on /dev/sdb1, /var/www/html, and /var/www/html/320 as well as the symlink galleries too. All recursive. chown apache:apache to everything too. PHP just can't read/write to it. I tried with and without the symlink, I've tried everything I can think of. Nothing. Any ideas how I can give apache/php permission to read/write to this drive? With 777 permissions all around it should already be able to.

    Read the article

  • Network access lags for Win7 when server network utilization is high

    - by Jeff Miles
    We have a Dell PE2950 file server running Windows 2008, hosting a DFS namespace of ~1.2 TB. This server has two Broadcom 1Gbps NICs teamed together. When there is high traffic going to the server across the network (greater than 200 Mbps), any Windows 7 client accessing a DFS share at the time experiences severe performance problems. For example: Computer A has an AutoCAD drawing opened directly from the DFS share. Performance is normal, not causing any issues. Computer B begins a file transfer, putting a 11GB file onto a different DFS namespace, on the same server Computer A immediately notices lag while using AutoCAD. The cursor momentarily freezes within AutoCAD every 10 seconds or so, and any browsing of the DFS share is extremely slow. Computer B completes file transfer, and performance resumes to normal for Computer A. This is only affecting Windows 7 clients, using a variety of hardware (desktop + laptop). All of our Windows XP clients see no performance impact during the file transfer. Things I have tried with no change: Had Computer A work from an entirely different RAID array from the file transfer destination Updated NIC drivers on clients and server Enabled TCP offload and receive side scaling on the server NIC (previously disabled when the issue began) Antivirus disabled during file transfer I am currently having a user test applications other than AutoCAD when the file transfer occurs, and will update the question with that result. Does anyone have any recommendations for resolution or additional troubleshooting steps?

    Read the article

  • How can I implement ansible with per-host passwords, securely?

    - by supervacuo
    I would like to use ansible to manage a group of existing servers. I have created an ansible_hosts file, and tested successfully (with the -K option) with commands that only target a single host ansible -i ansible_hosts host1 --sudo -K # + commands ... My problem now is that the user passwords on each host are different, but I can't find a way of handling this in Ansible. Using -K, I am only prompted for a single sudo password up-front, which then seems to be tried for all subsequent hosts without prompting: host1 | ... host2 | FAILED => Incorrect sudo password host3 | FAILED => Incorrect sudo password host4 | FAILED => Incorrect sudo password host5 | FAILED => Incorrect sudo password Research so far: a StackOverflow question with one incorrect answer ("use -K") and one response by the author saying "Found out I needed passwordless sudo" the Ansible docs, which say "Use of passwordless sudo makes things easier to automate, but it’s not required." (emphasis mine) this security StackExchange question which takes it as read that NOPASSWD is required article "Scalable and Understandable Provisioning..." which says: "running sudo may require typing a password, which is a sure way of blocking Ansible forever. A simple fix is to run visudo on the target host, and make sure that the user Ansible will use to login does not have to type a password" article "Basic Ansible Playbooks", which says "Ansible could log into the target server as root and avoid the need for sudo, or let the ansible user have sudo without a password, but the thought of doing either makes my spleen threaten to leap up my gullet and block my windpipe, so I don’t" My thoughts exactly, but then how to extend beyond a single server? ansible issue #1227, "Ansible should ask for sudo password for all users in a playbook", which was closed a year ago by mpdehaan with the comment "Haven't seen much demand for this, I think most people are sudoing from only one user account or using keys most of the time." So... how are people using Ansible in situations like these? Setting NOPASSWD in /etc/sudoers, reusing password across hosts or enabling root SSH login all seem rather drastic reductions in security.

    Read the article

  • Shared configuration for Eclipse on Debian server

    - by Joris Meys
    I've manually installed the latest Eclipse on our debian server and wanted to configure it so all users share the same configuration. It turned out less obvious than I thought: I don't seem to be able to install packages for all users. If I run it myself, all configuration data is saved under my own home directory. If I run Eclipse using sudo, everything is saved under the root directory but is not accessible for other users when they run Eclipse. I've been browsing the manual of Eclipse and some forums, but apart from a "yes, you can" I couldn't find any information on how that should be done. The biggest problem is installing plugins for all users to be found. Any help is greatly appreciated. Eclipse : 3.6.1 classic, installed using this procedure. Server uname: GNU/Linux * 2.6.26-2-amd64 Server is accessed using Putty, and Gnome desktop through realVNC. Just mentioning it if that is of any importance. Our sysadmin is on "prolonged leave" (working in Spain and never replaced), so I'm stuck without help here. EDIT : -- I asked this question also on StackOverflow as I wasn't certain this is a genuine server-related question. Please feel free to merge both questions at the appropriate place. --

    Read the article

  • UPS power requirements for server

    - by captainentropy
    Greetings! So, I just placed an order for a new server. The company recommended that I get a 3000W UPS. (!) As best as I could I calculated the following wattage consumption based on benchmarked data or datasheets provided by the manufacturers of each component: number watts **total watts** MoBo 1 240 240 CPUs (E5540) 2 80 160 RAID cards (3ware) 2 18 36 RAM (6x4GB) 6 3 18 DVD drive 1 7 7 floppy 1 2 2 RE4 drives 8 7 56 WD20 drives 8 6 48 Intel X25 SSD 2 0.15 0.3 total = 567 So that is for the PSU requirements only. The PSUs in the machine are a 720W for the master node and 800W each for two subsystems. That's a total of 2320W that can be delivered by these PSUs. But that is 4X the amount being consumed, at most, by the components. I didn't count case fans or the eSATA card (3W maybe?) or what the PSUs themselves require but assuming I double or triple my calculations I'm not even remotely close to the 3000W UPS I was suggested to get. They run at least $1100. I could get a 2000W for about $750 or a 1500W for $450 and still be well over my estimated power need. I don't think I need a whole lot of run time in the case of a power outage, maybe 20 minutes max, enough time to shutdown if the power doesn't come on within 5-10 minutes. Any thoughts? Am I off on my calculations? Did I overlook something major? If so what are your suggestions for a UPS? Thanks!

    Read the article

  • How to rename network printer on Windows 7?

    - by Adrian McCarthy
    This question is similar to How do you rename a printer device in Windows 7 64 bit, except the answers there do not work, and I'll provide more information. This is a home network, not a domain. I have set up a Brother HL-5170DN. It is a network printer connected directly to an Ethernet hub. I can connect to it with Windows 7, but on Windows 7 it defaults to the name "binary_p1 on Brn37415f", which isn't very useful. And I cannot seem to change the name. I have it working with several Windows XP and Vista machines, and I can change the name on those machines. On Windows 7 Printer properties: I can see the "binary_p1" name on the General tab. I can select the text, but I cannot change it. The field is not grayed out, but I cannot type anything into it. On the Ports tab, all of the controls are grayed out (disabled). The selected Port is called "\\Brn_37415f\binary_p1", and it's described as "Client Side Rendering Provider" and the printer field says "binary_p1". On the Security tab, I can see that my account has "Manage this printer" permissions. If I choose Printer Server Properties, I can select the port and click Configure Port, but I get a dialog that says, "An error occurred during port configuration. This option is not supported." I have found many forums with people asking the same question without getting an answer. Update: No more bounties to offer, but I'm still looking for a solution to this problem.

    Read the article

  • Is this normal or does my AVG anitivirus have a virus? [closed]

    - by user390480
    Possible Duplicate: Computer is infected by a virus or a malware, what do I do now? [Note: This is not a duplicate and should not be closed as a duplicate as this is nothing like the other question. I am not asking if I have a virus, nor am I asking "what do I do now". I know that I have a virus and I know what to do. However, I am asking if these are normal AVG ads or if it has been taken over.] My Windows XP PC started acting strange and I am right now actually in Linux running off of a USB drive. I am running Avast under Linux and it has discovered some viruses on my XP drive. Some of the strange things happening in XP were: I could not get to Google.com My Hosts file was set to hidden and read only My Hosts file had an entry of ::1 And AVG had ads in it I've never seen before. Maybe it is normal but I Binged for AVG anti-virus and become.com but found no information. (The red lines and question mark are by me) Any thoughts?

    Read the article

  • Am I able to forward traffic from an external subdomain to a specific local host?

    - by George Bowman
    I apologise in advance if the question doesn't make sense, please let me know. I've got a small LAN (~10 Virtual Servers) using Win Server 2008 as a DNS server. This is behind a smoothwall express 3.0 firewall with ports forwarded for specific services. I have a domain (123-reg) with the NS's that of afraid.org (DynamicDNS) and subdomains pointed to my (Dynamic) IP address e.g. subdomain1.example.com - 123.456.789.101. I think that adequately explains my set up. My question is, am I able to have subdomains e.g. subdomain1.example.com only point to a specific local host? Like so: subdomain1.example.com:80 - firewall(external facing) - server1.example.com:80 subdomain2.example.com:80 - firewall(external facing) - server2.example.com:80 I don't actually necessarily want to use port 80, otherwise I would just use VirtualHosts on apache, it is just an example port. Currently I can use either subdomain1.example.com OR subdomain2.example.com and they will both point to server1.example.com:80 I do not have to stay using Win Server 2008 for DNS, I am more than happy to move over to BIND if needs be, it was just easier to use Win Server 2008's DNS. I do not know if this is even possible, I have a feeling it isn't as I've only got one external IP address but any information is useful!

    Read the article

  • Is this way of using Excel 2007 Pivot table for BI scalable ?

    - by Sim
    Hi all, Background: We need to consolidate sales data across the country to do analysis Our Internet connection/IT expertise/IT investment is not quite strong, therefore full BI solution is out of question I tried several SaaS BI solution (GoodData, ZohoReports) and while they're good, they seem not to fully support what we need We're looking at 'bout 2 millions record for every 2 months My current approach Our (10) sites currently gathers data from all their branches and consolidate them into 1 Excel file with Pivot table and embed source data In HQ, I will request 10 sites to send back those Excel files periodically We will import those Excel to our MSSQL server There will be a master Excel file, that will also have the same pivot table (as those came from site Excel file), and datasource is the MSSQL server More details For testing, I currently use MSSQL 2008 Express on my laptop So far, I imported our transactions for the past 2 months and there are 2 millions+ row in 1 table in MSSQL (we just use 1 table, corresponding to our common pivot table structure). DB size is ~ 600 MB In the master Excel file, if not including the source data, it's just < 10MB. Including the source data will increase the size to 60 MB (so I supposed Office 2007 automatically zip the data ?) I try using the Pivot (drag-and-drop fields) and the performance so far is OK (my laptop specs: C2D T7200, 3GB RAM, Windows XP) So my question is : If we're looking at full year transaction (roughly 15 millions rows in MSSQL 2008 Express, 3.6 GB in size), is there any issue with that 15 million rows in 1 table in SQL Express ? Is there any performance issue with the pivot table at that time ? Can it still embed the source data ? (I google-ed but didn't find the maximum size of source data Excel 2007 can embed) Any other suggestions on how we can better do this ? Given that we can't afford the full BI solution, any light-weight/budget/SaaS BI that you can recommend ? Thanks

    Read the article

  • Proxmox drbd configuration split brain [on hold]

    - by AudioDan
    I am planning a proxmox HA configuration with two Dell R710 machines (dual 6 core processors in each) with enterprise level drive raid arrays. I would be using DRBD with a quorum disk on a third machine. I would dedicate two 1GB nics on each server to the DRBD communications. We would have approximately 12 to 14 Virtual Machines running on this pair of servers. The proxmox manual recommends creating two DRBD resources - one for the Virtual Machines that normally run on ServerA and one for the Virtual Machines that normally run on ServerB. This is because of the Primary/Primary state in which this configuration runs. If both servers have VMs talking to the same DRBD resource and a split brain situation occurs, there is potential for data corruption that must be resolved. While I understand it would take more effort to create new virtual machines, can anybody foresee any potential problems with running a separate DRBD resource for each VM instead? Does anyone have experience running a setup that way and has it worked well? It seems to me that would allow more flexibility in moving machines back and forth.

    Read the article

  • How to set up daisy-chained routers for separate sub-nets?

    - by joe
    This question seems to be similar to others, but I'll take a shot anyway. A client recently switched ISPs from TDS to Comcast Business Class. Before the switch, they had 5 static IP addresses assigned. Now they'll have a single IP address that will change whenever Comcast decides to do so. The issue is that this internet connection will be shared among two companies, both having (and wanting to keep) their own private subnets. Because TDS was supplying multiple IP addresses to the one location, this allowed me to put each router on the switch. Now, with Comcast, they only get one IP address, meaning there has to be a main router before the subnet routers. Luckily, the cable modem has a built-in router, which I would like to connect to each company's router, and still have DHCP enabled on all accounts. Question: What do I need to do to the subnet routers to keep them separate from each other, but still allow internet access from the main router. I would love to say "I tried this", and give you links, but everything I find on the internet only mentions daisy-chaining routers with DCHP disabled.

    Read the article

  • Why we can change our IP address?

    - by iamstupid
    I across some websites that offer change of our IP addresses. It says, we can surf net anonymously, including changing our IP address and location. Most of the softwares are not free, so I have not try it out yet. But my question is, so, IP addresses will no longer be unique or valid for identify which computer were sending/request the information? I though only the ISP can determine our IP, so we can change our IP from some commercial softwares huh? Case: If I change my IP address, I go to a website which is supposed to be banned by my country, will the ISP let me pass the check and I will be able to browse the website which should be blocked? another question: From what I know, if we want to go to certain website, here is the flow: My Computer = ISP = Website = ISP = My computer I am not sure, if its the correct flow, but I am sure that, whichever website I want to visit, I need to go through my ISP, isnt it?. So if we change out IP, our ISP will record our new IP or the original(assigned-by-ISP) IP? Sorry for my bad English.

    Read the article

  • Excel data representation: show me all people who did not pass the exam

    - by dreftymac
    Background I have an excel spreadsheet with the results of a pass/no-pass exam. Students are allowed to take the exam as often as they want until they either pass, or give up trying. student ;; result ;; date [email protected] ;; no-pass ;; 2000-06-07 [email protected] ;; pass ;; 2000-06-07 [email protected] ;; pass ;; 2000-06-07 [email protected] ;; no-pass ;; 2000-06-07 [email protected] ;; pass ;; 2000-06-07 [email protected] ;; pass ;; 2000-06-08 [email protected] ;; no-pass ;; 2000-06-08 Question Using a pivot-table or something else, how can I get excel to show me a clean report or representation of this data on another sheet that answers the question: Who are all the people who took the exam, but never got a passing grade? In the above example it would just show me [email protected] ;; no-pass ;; with all the dates that delta took the exam. I know excel is not a database nor a reporting tool per-se, but it would be great if I could get it to do this.

    Read the article

  • What is the max supported number of SATA devices (using cable adapters) on a Dell SAS 6/iR adapter?

    - by Zac B
    I've got a Dell SAS 6/iR PCI-E adapter. I don't have a multiplier backplane. I'm planning on connecting SATA (non SAS) drives. If I buy cable adapters only (ones that split a SAS connector on the card to a certain number of SATA cables), how many drives can I connect to this card? The way I see it, there are two limitations: a limitation imposed by the theoretical max number of devices supported on the card (which I've dug through the specs to find, but haven't seen yet), and a limitation imposed by the number of SAS plugs on the card multiplied by the number of SATA cables that come out of the highest-multiplying splitter I can buy. The answer to my question would be the minimum of those two limitations. I've seen 4x SATA coming out of some splitters; are there any that have more? Alternatively, if this is an RTFM question, does anyone have a good link to a "this is how SAS works, this is how you figure out the max number of devices, and this is how the concepts of 'ports', 'lanes', 'endpoint devices', and 'connectors' all relate in SAS-land" document? I've looked around on the Dell docs, but haven't found anything that explains this to someone at my level of understanding of SAN/enterprise storage technologies. Cheers!

    Read the article

  • How to organise storage for media content such as video and music?

    - by thor
    Currently, we have a single server hosting all content: music, video and software. This content is downloaded by users through HTTP. Now free space is coming to an end and we are exploring different ways of extending our storage capacity. We want to do it cheap, simple and reliable (protected from disk/ server faults). Currenly, we see two ways: Add a couple of cheap servers with 4 disks (RAID1 ?), run some distributed file-system on top, like GlusterFS. Pros: hopefully, we will see all our disks as single flat file system, just dump content into it and be done. Cons: could be tricky in configuration and handling of faults. Add a couple of cheap servers, all running HTTP servers. Each piece of content (be it a music file or video) is placed on randomly selected two servers. Pros: don't have to deal with RAID, as content is duplicated; single server failure does not bring down any part of content; doubled distribution capacity (as any signle file could be downloaded from any of two servers hosting it). Cons: requires some scripting on part of distribution of content, adding/ removing servers. Do we miss any other ways? Which of the aforementioned options seems to be the best?

    Read the article

  • How do I diagnose the cause of a freeze after resuming in Windows XP (SP3)?

    - by Software Monkey
    I have just built a new computer from parts. Whenever I resume from any sleep mode (S1, S3 or S4) the computer freezes within about 60 seconds of the welcome screen appearing. I have updated the BIOS and all drivers to current from the motherboard manufacturer's site. I have reset BIOS settings to default, including disabling AMD Cool n Quiet. The windows event logs are not helpful at all. Other than immediately after resuming the system is stable as long as AMD CnQ is disabled. The system is: Mobo : MSI 790GX-G65 CPU : AMD Phenom II 965 BE at 3.6 GHz Memory : Corsair DDR3 1600, at 1333 MHz and 9-9-9-21 HDDs : 1 EIDE, 2 SATA in RAID-0 DVD : 1 Card Reader: 1 multi-card reader Keyboard is attached via PS2 and mouse is USB. Any thoughts or pointers would be most welcome. EDIT: It appears that the computer may not freeze if a program is left running which puts it under significant load. I left a stress test running which keeps all cores under 85% load, and my son put the computer to sleep - while this program is running it I have been able to resume from S3 successfully 4 times, compared against about 20 tests with the computer idle which have all frozen. So this may be related to being in an idle state when it resumes.

    Read the article

  • mysql thread count

    - by Ryan M.
    We have a web application that uses apache and mysql. Generally (according to Munin) our MySQL thread count sits between 2 and 4 at all times. The other day, our server almost came to a halt. HTTP requests were slow or wouldn't go through at all, SSH would work, but would take 30+ seconds to register keystrokes, etc.. So we pull up Munin and the only thing that's out of normal boundaries is the Mysql thread count. CPU usage was under 1%, load was under 1.0, plenty of available RAM. As mentioned before, the thread count floats around 2 to 4. At the time of our slow downs it had spiked to 14. So I start poking around the Internet and I see that in most cases, you'll start to see a higher thread count when you start running into slow queries. If I understand it correctly, the request comes in that takes a while to process, in the mean time other requests are coming in, so a new thread will be created to work on the request (yes?). But at the time of the slow down, we had 0 slow queries. My question is: What else can cause mysql to create additional threads. And would this sudden spike in threads possibly cause the server to slow down? To fix the issue, we restarted apache and everything went back to it's beautiful, normal self. Considering the the Server Vitals (CPU, RAM, Network, etc) were all ideal, and the thread count was the only thing out of place, this seems like the most logical thing to pursue as the possible cause. If it matters, we're on Mysql 5.1.40. Server is FreeBSD 7.2 and the server in question is inside a jail.

    Read the article

< Previous Page | 403 404 405 406 407 408 409 410 411 412 413 414  | Next Page >