Search Results

Search found 12829 results on 514 pages for 'hard'.

Page 408/514 | < Previous Page | 404 405 406 407 408 409 410 411 412 413 414 415  | Next Page >

• Bad Intel DQ965GF motherboard? Fails memtest, but memory is good.

  - by Boden

  I've got a machine with a DQ965GF motherboard. Two days ago it started locking up hard. Ran memtest 3.3, 1.7, and TestMem 4. TestMem just freezes, memtest failed on moving 8 bit inversions. Letting memtest run eventually causes the system to restart. I pulled memory sticks one by one, and then replaced the memory with a couple of known good sticks. No luck. I switched power supplies, didn't help. Swapped video cards just to be safe. No help. When I start the machine I get a single beep before it POSTs. According to the manual, a single beep means: 1 beep - Refresh Error (with nothing on the screen and it is not a video problem) I'm assuming that the motherboard has failed since it's obviously not a RAM or power issue. Do you agree? NOTE: I also tried resetting BIOS defaults, and even flashed the BIOS to the latest version. I also ran the Mersenne Prime Test and the CPU seems to click along just fine. (Tried logging in to superuser with openid but it's not working for me today. Hope this gets through)

  Read the article

• To what extent is size a factor in SSD performance?

  - by artif

  To what extent is the size of an SSD a factor in its performance? In my mind, correct me if I'm wrong, a bigger SSD should be, everything else being equal, faster than a smaller one. A bigger SSD would have more erase blocks and thus more leeway for the FTL (flash translation layer) to do garbage collection optimization. Also there would be more time before TRIM became necessary. I see on Wikipedia that it remarks that "The performance of the SSD can scale with the number of parallel NAND flash chips used in the device" so it seems throughput also increases significantly. Also many SSDs contain internal caches of some sort and presumably those caches are larger for correspondingly large SSDs. But supposing this effect exists, I would like a quantitative analysis. Does throughput increase linearly? How much is garbage collection impacted, if at all? Does latency stay the same? And so on. Would the performance of a 8 GB SSD be significantly different from, for example, an 80 GB SSD assuming both used high quality chips, controllers, etc? Are there any resources (webpages, research papers, presentations, books, etc) that discuss correlations between SSD performance (4 KB random write speed, latency, maximum sequential throughput, etc) and size? I realize this does not really sound like a programming question but it is relevant for what I'm working on (using flash for caching hard drive data) which does involve programming. If there is a better place to ask this question, eg a more hardware oriented site, what would that be? Something like the equivalent of stack overflow (or perhaps a forum) for in-depth questions on hardware interfaces, internals, etc would be appreciated.

  Read the article

• Good visuals supporting adopting Macintosh in a Windows company

  - by jdmuys

  I work in a Windows only software service company, which just put up an internal contest for innovative ideas for the company. The idea I submitted is to let employees use a Mac instead of the mandatory PC if they wished to. My idea has been selected (among a few others) to reach the next stage of the contest. One of the items requested for the next stage is ONE visual that best illustrates the idea. While my pitch is rather good (I think), I have a hard time coming up with ONE visual that would be suggestive enough and not too fanboy-ish, or too restricted. That's why I am requesting suggestions. For reference, some of the points I intend to develop are (not in order): de facto safety (little or no malware) Apple as a company reached its leading position through innovation (bio)diversity is a source of value for a service company, that expands its reach. it makes financial sense the Mac is the most compatible machine, making it a lot easier to test our software (especially web sites). Some OS X technologies can be valuable to a software service company (eg Applescript) Some Apple tools can help us improve (eg Keynote) It's good citizenship for our company as Apple is now best in class according to Greenpeace. I realize this question may be out of topic here. I'd be happy to have suggestions on where to post this question. Please do not argue why OS X might be better or worse than Windows. My question is very narrow. Thanks.

  Read the article

• unable to copy file to folder, permission denied without explanation

  - by ValekHalfHeart

  Recently Norton Internet security deleted ml.exe (an assembler I use to program in masm32) off of my computer, thinking that one of the programs I had written with it was a virus (it was most certainly not). Fortunately, I had a copy of ml.exe backed up in an external hard drive, and tried to copy it over to my computer. The old ml.exe was located in C:\masm32\bin, so I tried to copy the new one to that location. After disabling Norton (which had opened the folder and preventing me from accessing it), I am still unable to copy the new file to C:\masm32\bin. When I tried, Windows announced that I would need Administrator permission to copy the file. Since I'm an admin, I figured this wouldn't be a problem although it was unexpected, as I have never had to provide administrator permission to access this folder before. However, instead of prompting me to enter my password, Windows simply refuses to copy the file: I repeat, I was not asked to provide a password. It simply says that I do not have permission. Does anyone know what's happening and how to fix it? Is Norton still causing problems, or it something else?

  Read the article

• Encrypting peer-to-peer application with iptables and stunnel

  - by Jonathan Oliver

  I'm running legacy applications in which I do not have access to the source code. These components talk to each other using plaintext on a particular port. I would like to be able to secure the communications between the two or more nodes using something like stunnel to facilitate peer-to-peer communication rather than using a more traditional (and centralized) VPN package like OpenVPN, etc. Ideally, the traffic flow would go like this: app@hostA:1234 tries to open a TCP connection to app@hostB:1234. iptables captures and redirects the traffic on port 1234 to stunnel running on hostA at port 5678. stunnel@hostA negotiates and establishes a connection with stunnel@hostB:4567. stunnel@hostB forwards any decrypted traffic to app@hostB:1234. In essence, I'm trying to set this up to where any outbound traffic (generated on the local machine) to port N forwards through stunnel to port N+1, and the receiving side receives on port N+1, decrypts, and forwards to the local application at port N. I'm not particularly concerned about losing the hostA origin IP address/machine identity when stunnel@hostB forwards to app@hostB because the communications payload contains identifying information. The other trick in this is that normally with stunnel you have a client/server architecture. But this application is much more P2P because nodes can come and go dynamically and hard-coding some kind of "connection = hostN:port" in the stunnel configuration won't work.

  Read the article

• My Computer hangs for a few minutes just after startup, and then is fine.

  - by EvilChookie

  So I just built myself a reasonably beefy computer, and I installed Windows 7 on it. However, I start the machine up each morning and within a few minutes, the computer will semi hang. That is the mouse is responsive, and most of the time I can open task manager, or a new tab in Chrome. Occasionally windows will be labelled as 'Not responding'. Then, the machine will get over it's problem, and will be nice and quick until I turn it off. Here's my specs: CPU: AMD Phenom-II X4 955 Black (Quad Core, 3.2ghz) RAM: 4GB of DDR3 1300 MOBO: ASUS M4A785T-M (Latest BIOS) HARD DRIVES: 2x1TB Western Digital Caviar Blacks in RAID-0. OS: Windows 7 Ultimate x64. GPU: ASUS GT240 1GB. I believe this issue relates to the RAID array, as I didn't have the lockup problem before I created the array. I purchased a second drive and reformatted after creating a RAID array, since the single drive was a little on the pokey side (compared to the rest of the computer). What I have tried: Updated Raid Drivers Malware checks Windows Updates Unecessary Services CPU and Disk activity appears to be low (via Resource Monitor) No strange errors in the error log. Any thoughts?

  Read the article

• Handling the Outlook 2007 AutoArchive PST file

  - by Doug Luxem

  We encourage our users to enable AutoArchive in Outlook 2007 as a way to manage their mailbox sizes. However, we frequently end up running in to problems with the archive.pst file that is generated. The two main problems we have are: The archive.pst file is located in the user's local profile directory and is never backed up. A dead hard drive or stolen laptop could result in months or years of missing email. All other personal data is stored on network shares, but we can't do that for Outlook PST files. Without some sort of manual intervention, the archive will grow to enormous sizes. Although Outlook 2007 SP2 handles the large files better than before, it still results in slow response times from Outlook and an increase likelihood of a corrupt PST file. To mitigate these problems personally, I move the archives to a c:\Outlook folder and manually back that up to a shared drive every month or so. Additionally, I rotate archive files every year so that I have one file for each year (archive2008.pst, etc). Obviously, asking our users to do this same wouldn't help much. We need some sort of automated solution to take care of points 1 and 2. I have to imagine this is a common problem for Exchange organizations, so what is the best method to handle this?

  Read the article

• Is there a good alternative to Videora iPod Converter?

  - by Richard

  I use Videora to convert my videos (in DivX/XviD format) to something I can play on my iPod Classic. I really dislike it. It's clunky, riddled with adverts, sometimes doesn't convert properly (the infamous "invalid public atom" error - see Google for more) and has a UI that truly stinks. On the upside, it's free, accepts a list of video files (via the oddly hard to find "1-click convert" button) and just gets on with the converting as it already knows the correct settings for my iPod. One final nice touch is that once they are converted, it'll automatically upload them into iTunes. Are there any alternatives which have all the upsides but none of the downsides? Bonus points if they can set the metadata in iTunes correctly for TV shows (season, show, episode) and delete the converted file afterwards (as my iTunes settings means that a copy is made elsewhere). I've looked at a bunch of applications (handbrake, virtualdub, mediacoder, format factory, any video converter, convertxtodvd) but many of them fail the "just select a list of files and get on with converting" test - let alone all the other features I want. I have no desire to individually set the video size of each file or the codec or the post-processing options. I'm currently using the command line version of HandBrake (handbrakecli) and a hand-written DOS batch file to go through every file in a folder and convert it. It does most of what I want, just not in a very slick way. Can anyone recommend anything better? It needs to work on Windows 7 and be free.

  Read the article

• Can somebody please recommend a good local file backup utility that will be Windows & OSX Compatible?

  - by JAG2007

  I have an external hard drive that I keep all of my work files on and transfer them back and forth between my Windows 7 box at work, and my Mac at home (I work from home frequently). Can someone recommend a really good backup utility that I can use on that external drive, to back the files up to my work computer locally, or the other external drive on my machine at work? I'm looking for preferably a free or open source software, and I'd prefer it to be cross system compatible, although I would also consider using a software that will only work on the Windows box. Also, I will consider a software that has a price assuming it is a really good piece of software and the price is reasonable (like under $50 or so). I checked out CrashPlan a bit, but not sure if that's gonna be really what I'm looking for. To reiterate I'm not looking for online backup solutions, just a piece of software that can back up my data to another drive locally. CrashPlan Free seems to offer this, but not sure how good it is (considering their goal is to get me to buy a pay for version). *NOTE: I'm running Windows 7 in 64bit so I need a piece of software that will be compatible with 64bit OS. My previous software, PC Backup, is not. That's partly why I'm in this boat.

  Read the article

• I cannot access Windows Update at all

  - by Cardinal fang

  I have been unable to access the Windows update site for a couple of weeks now. I just get a message saying "Internet Explorer cannot display the webpage" and saying I have connection problems. Same thing is replicated with any other Microsoft site I try to access. The Automatic Updates also do not work. I can access every other wesbite I've surfed to. I've tried Googling the problem and based on what other site have suggested I have cleared my cache and temp files. I've scanning my hard drive with my antivirus in case I have a virus (nada). I've tried turning off my firewall and anti-virus (I run Zone Alarm). I've downloaded SpyBot and scanned my drive with that in case something was missed by Zone Alarm (again nada). Based on suggestions from the smart cookies on the Bad Science forum, I've used nslookup to check my translation isn't wonky (got all the info they said I should get). I've also tried navigating there directly using the IP address I was given (nope). I normally access the internet through a 3 mobile broadband connection, but have also tried connecting using a mate's wi-fi connection in case it was something on my mobile modem interferring. I run Windows XP SP3 with Internet Explorer 7 and Zone Alarm Internet Security Suite as my anti-virus/ firewall. Any suggestions?

  Read the article

• Server 2008 R2 domain windows update strategy

  - by Joost Verdaasdonk

  Let me explain my question a bit. We are a small company that have now made the first move to a bigger network. For now the network contains of 5 servers 2008 R2 (dc,sql,web,etc..). Everything we need is now in place but for now we cannot afford to finish the network by implementing redundant systems. (secondary dc, dns, sql cluster, etc...) For some people this is hard to understand but this is the current situation. (and we are aware and will fix this when we can) Because we want to keep our system secure and up to date I've made sure that all systems are updated regularly. The problem is ofc that the nr of updates Microsoft rolls out that need a system reboot seam to occur more often. (maybe I'm wrong and it just feels like this) ;-) In our domain servers depend on each other for services (like SQL, WEB, or whatever) so just rebooting a server at will is NOT a good idea! For now I update all of them without rebooting at once. After all are up to date I bring them down in the order they are depended on each other. After this I reboot all of them in the inverse order. I understand ofc that if I DID have redundancy in my system that updating and rebooting would not be such a problem because the server task could be taken over by another node but this is something we generally need to add when we can. So my question is. If you read my above situation can you suggest me more Update strategies or general ideas that could help me do this process in a better / faster way? Thanks for your thoughts!

  Read the article

• 10GE network: Is it still deadly expensive? Any options?

  - by BarsMonster

  Hi! I am building home cluster where I going to have about 16 nodes which can live with 1G ports, but I really want to have 10GE on file server & central node. It's all local, so no need for cabels longer than 3-5m. And ofcourse I want to spend as little money as possible (not going to spend more than whole cluster costs) :-) What are my options? 1) Legacy solution is to take some 24-48 port 1GE switch, and connect to file/central nodes via 4-8 aggregated links. This will work I guess, cost is very acceptable, but I am not sure if it's ok to use that much aggregated links. And ofcourse it would be hard to double bandwidth when needed... :-D 2) Switch with several 10GE uplink 'ports'. As far as I see, they all require modules which costs about 1000$, so I will need 4 10G modules, and 2 10GE cards... Smells like way more than 5000$+... 3) Connect file & central node via 2 10G cards directly, and put 4 quadport 1GE NICs on fileserver. I am saving on 2 10G modules and a switch, fileserver will have to do packet routing, but it's still gonna have alot of CPU's left :-) 4) Any other options? Infiniband? 5) Are MyriNet adaptors works fine? I guess there are no cheaper options? 6) Hmm... Scrap fileserver, put it all on central node and provide dedicated 1GE port for each of the nodes... This is sad...

  Read the article

• HP Pavillion DV6500 recovery disk failure

  - by Scott W

  I recently attempted to re-install Windows Vista on an HP Pavillion DV6500 using the factory recovery DVD's, but encountered a strange problem. When the recovery disk attempted to reformat the hard disk, it failed at 22%. The error message provided was not very informative, just the error code "0x400110020000 1005". A google search turned up some people with a similar problem who asserted that HP has been know to ship corrupted recovery DVDs. The recovery disk did manage to reformat the the recovery partition before failing though, so recovering from the partition is no longer an option. It would be possible to reinstall from an off-the-shelf retail copy of Vista and then pull the drivers from HP's website, but I don't have access to a copy of Vista, and it would really be outrageous to have to purchase a new OS when I have a perfectly valid license already. Thought about biting the bullet and upgrading to Windows 7, but my understanding is that without Vista installed I'd be unable to use the upgrade version, and be forced to purchase the more expensive non-upgrade retail copy (!). Can anyone suggest a possible solution to this Catch-22? I've run out of ideas.

  Read the article

• Possible boot conflict?

  - by Evan Kroske

  I was installing Ubuntu on a computer on which Windows XP was already installed. The computer has multiple hard drive bays, so I decided to remove the XP HDD and install Ubuntu on a blank HDD when it was the only HDD in the system. Unfortunately, if I now try to boot Ubuntu with the Windows XP drive in the second slot, nothing will boot. However, if Windows XP is in the first slot, it will boot fine. Can anybody explain why this happens? When I was checking out the BIOS to see if something was messed up, I discovered that when Ubuntu is in the first slot, the BIOS doesn't recognize any HDDs. However, if XP is in the first slot, the BIOS recognizes both drives. Any hypotheses about why this happens? Edit: Here's the setup. I have an old server with seven SCSI HDD slots. I have five identical 68 Gb SCSI drives, but I can keep only two plugged in. XP is still installed on the first drive, but I reinstalled Ubuntu on the second drive and had Grub overwrite the XP bootloader on the first drive. Now, the setup works fine, and I can use Grub to load either XP or Ubuntu. However, if I plug in another identical blank HDD in the third slot, the computer recognizes only the XP drive and doesn't boot. Grub starts to load, then gives me a "disk not found" error. Running ls from the grub rescue prompt only shows one drive with two partitions. I guess this is a BIOS problem, but I'd still like to know what triggers it. What about a blank drive could cause the BIOS to freak out?

  Read the article

• KeePass lost password and/or corruption due to Dropbox/KeePassX

  - by GummiV

  I started using Keepass about a month ago to hold my passwords and online accounts info. Everything was stored in a single .kdb file, only protected with a password. I'm using Windows 7. Now Keepass can't open my .kdb file with the error "Invalid/wrong key". I'm fairly confident I have the right password. Altough I might have mixed up a few letters I've tried about two dozen different combinations to minimize that possibility - but can't rule it out though. My guess is however that the .kdb file got corrupted, either due to Dropbox syncing (only using it on one computer though) or because I edited the file using KeePassX on Ubuntu (dual boot on the same computer, accessing a mounted Win7 NTFS partition), or possibly a combination of both. I have tried restoring older versions(even the original one) from Dropbox and trying out all possible passwords without any luck. (which does seem to rule out KeePassX as the culprit, since oldest copies are before I edited the file from Ubuntu) I have tried opening the file with the "Repair KeePass Database file" which always gives the "0xA Invalid/corrupt file structure" (the same error for when a wrong password is typed). I was wondering if there was any way for me to salvage my hard-gathered data. I know generally that brute force cracking is not feasible, but since I can remember probably more than half of the usernames/passwords, any maybe the fact that one of them does come up fairly often (my go-to pass for trivial stuff), that might simplify the brute force process to a doable time frame. Maybe the brute-force thing might incorporate the fact that I know the password length and what characters it's made from. (If we assume corruption, not a password-blackout on my part) I could do some programming if there are any libraries or routines that I could use. Other people seem to have had a similar probem http://forums.dropbox.com/topic.php?id=6199 http://forums.dropbox.com/topic.php?id=9139 http://www.keepassx.org/forum/viewtopic.php?t=1967&f=1 So hopefully this question will become a suitible resource for people when searching the web. Feel free to tell me if you think this should rather be a community wiki.

  Read the article

• Creating Custom ISO Images

  - by ericl42

  I am working on creating some custom ISO images using primarily Fedora and CentOS. I want the image to be a bootable live CD with some specific files on it. I also want it to have the option to be able to be downloaded to the hard drive. I've read some various articles but want to get a few more opinions since I've never done this before. Currently I'm trying 2 different methods. Install Fedora with the configuration exactly how I want it and then run the livecd-tools program to pull everything I currently have to an ISO. I haven't got this to work yet but I do see a few issues with it. Such as the default passwords I had to put in. Run a Fedora live CD and install a few things I want on it and then copy the image of it. I believe this would work better since it has more of a live cd feel. However I"m not 100% sure how I should go about pulling the current image to my own ISO. I know some people have said to use mkisofs and a few other programs but any advice would be greatly appreciated.

  Read the article

• Important hardware components to avoid bottlenecks/improve speed on a laptop?

  - by joelhaus

  Looking for a powerful general use (including web development) laptop running Windows. Price points seem to be all over the place. Many less powerful machines are priced much higher than machines with better specs. How does one navigate this market? Are there any unpublished/under-publicized specs/bottlenecks you look for? Understanding that hardware improves over time, is there an efficient ratio that can be used (or something similar, like Windows Experience Index?) which will indicate how powerful a system is? Thanks in advance! P.S. Here is an example from a laptop released on September 17, 2010. Can anyone pick apart these specs? Is there missing information you would be looking for? OS: Win 7 Display: 16.4" LED backlit Processor: Intel Core i7-740QM, 6MB L3 Cache RAM: 6GB DDR3 1333MHz (8GB max.) Graphics: NVIDIA GeForce GT 425M (1 GB of dedicated DDR3) HDD: 500GB 7200RPM SATA Hard Drive Removable Disc: Blue-ray with DVD±R/RW Misc: webcam/mic/speakers/bluetooth (via Sony Vaio VPC-F137FX/B)

  Read the article

• Does MySQL have some kind of DoS protection or per-user query limit?

  - by Ghostrider

  I'm a bit at a loss. I'm running a MySQL database that's roughly 1GB data in indices combined on a dedicated Linux server. DB version is '5.0.89-community'. Configuration is controlled via cPanel. PHP actually runs elsewhere on a shared hosting. IP addresses are static and don't change. Access from remote IP address is properly configured. Website gets around 10K hits per day with each hit generating a a database query. Some of these queries are expensive (~1 sec execution time). All is fine and well until at some point DB server starts refusing connections from the client, claiming that specific user can't access the server from that IP. Resetting the server will always fix the problem for a day or two and then the same thing happens. There are some other DBs on that server, some of which are hit pretty hard on occasion but constantnly. One of the apps maintains several persistent connections since it does couple of updates per minute. Though I don't think it's related. What's driving me mad is that I can't figure out why server would start refusing connections. There is nothing in the logs. This server is a hosted dedicated server so hosting company created the OS image and I didn't write or go over every line of configuration. I'd do it but I'm at a loss as to where start looking. Any advice is appreciated.

  Read the article

• What can cause a kernel hang on redhat 4?

  - by Ivan Buttinoni

  I've to solve a nasty problem on a ten machine "cluster": randomly one of these machine hang during an hard computation, sometime still ping sometime not. The problem was described me at the phone, I've still no touch/see these machine, so I can't be more precise. It seem there's no (real) keyboard or monitor linked to them, so I haven't nothing about keyboard led or messages on monitor. Don't worry, what I really need is some suggestion where to search the problem, some suggestions on what can cause a kernel hang on a working machine. I also see this post, but seem same need on a different situation. My ideas since now: - HW problem (ram, cpu, fan etc.) - bad autofs configuration - bad nfs(?) configuration - presence of a trojan/hacker/etc - /dev/"swap" linked to /dev/zero - kernel out of memory(??) - kernel bugged In other words I try to imagine what kind of envent can occour that can crash the kernel insted of the application that generate the event. What hang have YOU experienced before? Write it to me! TIA

  Read the article

• Adding subnet to a vsphere with single vcenter and esxi host

  - by Ilya Rakhlin

  Let me start of by saying that I do not specialize in networking, I am in the process of adding additional VMs to a testing environment and wanted some recommendations. In this case I am running a single ESXI 5.1 host and a single Vcenter management server. The problem is, I need another range of IP addresses added to the existing setup; hopefully without reconfiguring everything. Currently the esxi host is configured to IP: 192.168.100.200, gateway: 192.168.100.1 and subnet: 255.255.255.0. All of the VMs are running some version of linux with hard coded IP addresses in that range, and using that subnet. The VMs I am about to deploy I want to be on the 192.168.101.X network. Is it possible to add an additional subnet to this existing system that will also communicate with the current subnet? The esxi host has 6 physical NICs but only one connected as it is only a testing system; not sure if that matters. Are there any other ways to accomplish this hopefully without restarting or at least reconfiguring the IP addresses for each VM? Reason: Due to the configuration of the VMs to run the applications that we need I am using a large amount of the current IPs in the potential range (mostly VIPs). I will be setting up a new version of this “environment” while keeping the old one, thus potentially running out of IP addresses.

  Read the article

• FWBuilder DNS Object Run Time - when exactly does it resolve the DNS name?

  - by Jakobud

  In Firewall Builder, when you use the DNS Object and set it to run time, when exactly does the firewall (iptables in our case) actually resolve the DNS name? Is it whenever a call is made to that DNS name in the firewall? So the firewall would resolve the name on the fly whenever someone/something tries to access that DNS name? Or is it when you execute the fw script to load the rules into iptables? So in this case, it would resolve the DNS name that one time and then hard-code the resulting ip address into the iptable rules? From what I read, I think its #1, but it's just not 100% clear to me. We have two servers for a certain function on our network. One is the primary server and one is backup. alpha0.domain.com alpha1.domain.com In DNS we have this: alpha.domain.com -> alpha0.domain.com If the primary server goes down and we need to switch to the backup, I just change our local DNS record to point to alpha1.domain.com instead. So back to the firewall, if I just put in a Domain Object as alpha.domain.com, do I have to reload the firewall rules every time we switch to the backup alpha server and change the DNS record? Or will the firewall automatically resolve to the correct address even after the switch?

  Read the article

• How to install Windows 7 on a MacBook with HDDs and no optical drive, without rEFIt

  - by user1238528

  I just removed the SuperDrive on my MacBook Pro and replaced it with an SSD. So now my laptop has a SSD, and a HDD, but no optical drive. I have Lion on the SSD and I want to install Windows 7 on the HDD. Unfortunately, Boot Camp only will install Windows off of the Windows DVD. I have made a bootable Windows 7 thumb drive but my MacBook Pro won’t boot off it. So my question is how can I install Windows on the other HDD? I have thought about maybe using Oracle VirtualBox to install it on that hard drive, but I don’t know if that would allow me to boot directly into Windows. I really don't want to go down the whole virtualization route. I know I could just take out the SSD, put back in the optical drive, run the Windows 7 DVD, take the optical drive back out, put the SSD back in. But that sounds like a nightmare. Also, I really don’t want to use things like rEFIt. Any advice?

  Read the article

• How/when do you study?

  - by Sergei

  Would be interesting to find out how other sysadmins are educating themselves. I find myself in the need of constantly learning new things. I prefer to spend more time on the subject and know it thoroughly knowing that not doing so will kick me back in the future. This can be frustrating sometimes as it feels that I move too slowly. Our company has account on safari.oreilly.com and I am reading a book or two at any given time. I also read sysadmin related blogs for ideas and tips and to keep myself in the tune with the trends. I cannot do any study at home as I would rather spend my out of work hours with my family plus I find it hard/impossible to study at home due to the inability to concentrate at home. So I mostly study while on the train, luckily my commute time takes up to 2 hours a day. I also read a lot at work and don't feel guilty about it. To fix/implement/plan, I need to have a solid knowledge and if it requires time then this is a part of my job being a sysadmin. There is a joke that says "sysadmin is a person that knows a lot about everytihng and as a result knows nothing" - I think ther is a grain of truth here...

  Read the article

• Linux disk usage analyser that acts like symlinks are real files

  - by Rory

  I am using git-annex, an extension to the DVCS git, which is designed for handling large files. It makes heavy use of symlinks. The actual large files are moved to the .git/annex directory and the original files are symlinked to there. I am running out of disk space, and need to clear up, and see what's using all my space. Usually I'd use a disk usage tool like ncdu, Baobab or Filelight. However they treat the symlink as essentially empty, and only count the file that it is pointing to as using any space. Which means when I use git-annex, it shows no space used in the main directories and lots of space used in the .git/annex directory. This is not helpful. Is there any (graphical or ncurses) based disk usage programme for linux (apt-get installable would be easie that is capable (through options or not) of counting a symlink as using up the space that the original file uses up? Many have options for different behaviour for hard links, so makes sense that some should h (I know counting symlinks as using space has flaws, like counting the space space twice, broken symlinks, etc. But that's OK for my purposes)

  Read the article

• why is Mac OSX Lion losing login/network credentials?

  - by Larry Kyrala

  (moved from stackoverflow...) Symptoms So at work we have OSX 10.7.3 installed and every once in a while I will see the following behaviors: 1) if the screen is locked, then multiple tries of the same user/pass are not accepted. 2) if the screen is unlocked, then opening a new bash term may yield prompts such as: `I have no name$` or lkyrala$ ssh lkyrala@ah-lkyrala2u You don't exist, go away! Even when our macs are working normally, everyone here has to login twice. The first time after boot always fails, but the second time (with the same password, not changing anything, just pressing enter again) succeeds. Weird? Workarounds There are some workarounds that resolve the immediate problem, but don't prevent it from happening again: a) wait (maybe an hour or two) and the problems sometimes go away by themselves. b) kill 'opendirectoryd' and let it restart. (from https://discussions.apple.com/thread/3663559) c) hold the power button to reset the computer Discussion Now, the evidence above points me to something screwy with opendirectory and login credentials. Some other people report having these login problems, but it's hard to determine where the actual problem is (Mac, or network environment?). I should add that most of the network are Windows machines, but we have quite a few Macs and Linux machines as well, but I'm not sure of the details of how the network auth is mapped from various domains to others... all I know is that our network credentials work in Windows domains as well as mac and linux logins -- so something is connecting separate systems, or using the same global auth system.

  Read the article

< Previous Page | 404 405 406 407 408 409 410 411 412 413 414 415  | Next Page >