Search Results

Search found 13862 results on 555 pages for 'questions'.

Page 408/555 | < Previous Page | 404 405 406 407 408 409 410 411 412 413 414 415  | Next Page >

  • RPC Server Unavailable on Hyper-V cluster when moving resources after the host adapter has failed

    - by Doug Luxem
    On a Windows 2008 R2 SP1 cluster running Hyper-V, a lost network connectivity on the primary host interface. The interface was rapidly flapping up and down, and this was later determined to be caused by a faulty switch port. As this was a clustered server, the host interface was not fault tolerant (seeing as how the whole server was fault tolerant), so connectivity to the host was going up and down. The Hyper-V guests were completely unaffected by the network outage as they used a dedicated trunk on the server separate from the host interface. Additionally, dedicated interfaces for the cluster and live migration networks were fine. In order to diagnose the server, I tried to move all resources (Hyper-V Guests) to other nodes through Failover Cluster Manager. These moves failed with an error RPC Server Unavailable. The only way to move resources was by shutting down the guests, stopping the cluster service on the Node A, allowing other nodes to take ownership of the resources, and restarting the guests. A few other notes: All nodes have Client for MS Networks and File & Printer Sharing enabled on the Cluster and LM networks. Node A was accessible over cluster and LM networks from other nodes (these are private, cluster-only networks); pingable, CIFs, etc. Accessing \\NODEA is done over the Host adapters, as you would expect in this case and is the reason for the RPC Server Unavailable error with that adapter being down. My questions here are - Is there a way to still use Live Migration in a failure scenario such as this to prevent shutting down the Hyper-V guests? How can the network be reconfigured in the future so that the cluster service attempts to use the cluster and/or live migration networks to issue the RPC requests?

    Read the article

  • esx5 debian VM vlan setup

    - by Kstro21
    i have a server with ESX5, have a switch with about 20 vlans, this is how setup the trunk port interface GigabitEthernet0/1/1 description ToOper port link-type trunk undo port trunk allow-pass vlan 1 port trunk allow-pass vlan 2 to 14 stp disable ntdp enable ndp enable bpdu enable then, i created a standar switch(sw1) using the vSphere Client, the VLAN ID is set to All (4095), i also created a VM with Debian 6, with a NIC connected to sw1, now, i want to configure this NIC for a selected group of vlans auto vlan10 iface vlan10 inet static address 11.10.1.0 netmask 255.255.255.224 mtu 1500 vlan_raw_device eth0 auto vlan14 iface vlan14 inet static address 11.10.1.65 netmask 255.255.255.248 mtu 1500 vlan_raw_device eth0 so, when i restart the network using /etc/init.d/networking restart, i got this error Reconfiguring network interfaces...SIOCSIFADDR: No such device vlan14: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device SIOCSIFBRDADDR: No such device vlan14: ERROR while getting interface flags: No such device SIOCSIFMTU: No such device vlan14: ERROR while getting interface flags: No such device Failed to bring up vlan14. done. this is just part of the error, so, my questions is: is this possible?, i mean, what i'm trying to achieve using ESX Virtual Machines, VLANS, etc is this a Debian problem? can be solved? i've read about a file named z25_persistent-net.rules in Debian but it doesn't exist in my installation. in the In the vSphere Networking for ESX5 guide, you can read: If you enter 0 or leave the option blank, the port group can see only untagged (non-VLAN) traffic. If you enter 4095, the port group can see traffic on any VLAN while leaving the VLAN tags intact. So, in theory, it should work, right? Hope you can help me up with this one Thanks

    Read the article

  • Windows 7 Blank Screen on Boot / Login

    - by Greg
    I have a new system that's having a few problems... sometimes (seems to be when the PC is cold, i.e. has been switched off for a while, though that could be my imagination) I get a blank blue screen when I boot up. The system boots normally and auto-logs-in. The desktop loads and I'm even able to launch applications, but then everything disappears and the screen goes to the default windows desktop blue colour (not the desktop image, just a plain blue with no mouse cursor). At this point the machine completely locks up - I'm unable to even toggle Num Lock and have to hold in the power button for 5 seconds to kill it. Interestingly if I manage to launch some applications before it goes blank, they will usually crash... sometimes explorer.exe will crash too. When I reboot, the system is fine and stable. I've installed the latest graphics drivers and run memtest86+ for 6 passes (and counting) with no errors. The system specs are: CPU: Intel I7 2.66 @ 3.4GHz RAM: 6GB (3 * 2GB DDR3) HDD: 128GB Crucial M225 SSD Motherboard: Gigabyte EX58-UD3R Gfx: ATI Radeon Sapphire 5870 1GB Note: There are a few similar questions but I haven't found one that matches my symptoms

    Read the article

  • Setting up ssh config file with id_rsa through tunnel

    - by Rubens
    I've been struggling to set up a valid configuration to open a connection with a second machine, passing through another one, and using an id_rsa (which requests me a password) to connect to the third machine. I've asked this question in another forum, but I've received no answer that could be considered very helpful. The problem, better described, goes as follows: Local machine: user1@localhost Intermediary machine: user1@inter Remote target: user2@final I'm able to do the entire connection using pseudo-tty: ssh -t inter ssh user2@final (this will ask me the password for the id_rsa file I have in machine "inter") However, for speeding things up, I'd like to set my .ssh/config file, so that I can simply connect to machine "final" using: ssh final What I've got so far -- which does not work -- is, in my .ssh/config file: Host inter User user1 HostName inter.com IdentityFile ~/.ssh/id_rsa Host final User user2 HostName final.com IdentityFile ~/.ssh/id_rsa_2 ProxyCommand ssh inter nc %h %p The id_rsa file is used to connect to the middle machine (this requires me no password typing), and id_rsa_2 file is used to connect to machine "final" (this one requests a password). I've tried mixing up some LocalForward and/or RemoteForward fields, and putting the id_rsa files in both first and second machines, but I could not seem to succeed with no configuration whatsoever. Hope somebody can help me here! Regards! P.S.: the thread I've tried to get some help from: http://www.linuxquestions.org/questions/linux-general-1/proxycommand-on-ssh-config-file-4175433750/

    Read the article

  • Are SATA II and SATA 3.0 Gbps compatible?

    - by Johnny Maelstrom
    I am trying to check that if I buy a new internal HDD it will work in the NAS I am buying. Currently I'm confused about naming schemes and once that is resolved whether there is compatibility. I will gladly author this question to be more general if there is not already an article helping with the confusion of SATA naming and standards. I see similar, but not identical questions and will accept this as a duplicate if thought as such. The specifications on the eCommerce site for the NAS says, "Controller Interface Type Serial ATA-150", the product home page for the manufacturer says, "Compatible with SATA and SATA II HDD". The specifications on the eCommerce site for the hard drives say, "Interface Type Serial ATA-300", the product home page for the manufacturer says, "Interface SATA 3.0 Gbps" Wikipedia says many things about different naming conventions, the closest being, "SATA II 3.0 Gbit/s, which was colloquially referred to as "SATA 3G" [bps] or "SATA 300" [MB/s] since 1.5 Gbit/s SATA I and 1.5 Gbit/s SATA II were referred to as both "SATA 1.5G" [b/s] or "SATA 150" [MB/s]). Therefore, they will operate with negligible differences between them." Are SATA II and SATA 3.0 Gbps the same? I feel I'm tantalisingly close to getting a definitive answer here before I purchase, but really want to clear up these naming schemes.

    Read the article

  • Installing sphinx on a web hosting server

    - by fiftyeight
    I want to install sphinx search on a web-hosting server. I'm on a Linux VPS with hostgator, but I never actually installed anything on a remote server so this will be a first time for me. If there's anyone here who installed sphinx it's really help me I had some problems when using sphinx on my PC with the permissions and the MySQL files, eventually I got it working on my PC. Anyway, I'd me really grateful if anyone can help me with some questions Do i need root access to install sphinx? I have root access to the server but I'd connect to it as a normal user since doing stuff as root is always less secure. can anyone tell me by what user I need to execute the indexer and the search daemon? Should I use root access in order to this? when I did it as a normal user on my PC it gave me some trouble with the PID file and the log files. last time I executed the search deamon I executed it as a normal user and it gave me some trouble, I created the folder /var/log/ for log files and did chmod 777 on it, but still when I executed the search daemon it created the PID file "searchd.pid" file but with no permissions for some reason, any idea why? Thanx in advance. fiftyeight

    Read the article

  • IP tables blocking access to most hosts but some accesses being logged

    - by epo
    What am I getting wrong? A while back I locked down my web hosting service while hardening it or at least trying to. Apache listens on port 80 only and I set up iptables using the following: IPS="list of IPs" iptables --new-chain webtest # Accept all established connections iptables -A INPUT --protocol tcp --dport 80 --jump webtest iptables -A INPUT --match state --state ESTABLISHED,RELATED --jump ACCEPT iptables -A webtest --match state --state ESTABLISHED,RELATED --jump ACCEPT for ip in $IPS; do iptables -A webtest --match state --state NEW --source $ip --jump ACCEPT done iptables -A webtest --jump DROP However looking at my apache logs I notice various log entries in access_log, e.g. 221.192.199.35 - - [16/May/2010:13:04:31 +0100] "GET http://www.wantsfly.com/prx2.php?hash=926DE27C156B40E55E4CFC8F005053E2D81E6D688AF0 HTTP/1.0" 404 206 "-" "Mozilla/ 4.0 (compatible; MSIE 6.0; Windows NT 5.0)" 201.228.144.124 - - [16/May/2010:11:54:16 +0100] "GET /w00tw00t.at.ISC.SANS.DFind:) HTTP/1.1" 400 226 "-" "-" 207.46.195.224 - - [16/May/2010:04:06:48 +0100] "GET /robots.txt HTTP/1.1" 200 311 "-" "msnbot/2.0b (+http://search.msn.com/msnbot.htm)" How are these slipping through? I don't mind the indexing bots (though I am a little surprised to see them get through). I suppose they must be getting through using the ESTABLISHED,RELATED rules. And no, I can't for the life of me remember why the first match state rule is there So 2 questions: is there a better way to set up iptables to restrict access to specified hosts? How exactly are these 3 examples slipping through?

    Read the article

  • What is the oldest hardware still in production use? How is it kept running?

    - by sleske
    In the spirit of the question What is your oldest hardware that still works?, I'd like to ask: What is the oldest hardware you know that is still in production use? And what challenges did you (or someone else) face in keeping it running (scarce documentation, no support, no spare parts available...)? Most organizations will retire / upgrade software and hardware after 5-10 years, but sometimes old software is kept running on old boxes, because it "just works". I once worked at a client site that was running a critical piece of (in-house developed) business software on a single server running HP-UX. The server was old (ca. 12-13 years), but fortunately still running without problems; however, getting spares would have been very difficult, and since software installation was undocumented, any significant system changes or even new hardware might have caused significant downtime and data loss. We eventually managed to replace it, but this is not always possible. I also read that many organizations still run decade-old mainframe hardware, particularly for highly customized systems controlling industrial machines or power plants. Which old hardware have you encountered? How did you manage these challenges? Related question: http://serverfault.com/questions/82467/should-old-servers-be-retired

    Read the article

  • Windows Server Connected to Domain Without Being Domain Controller

    - by saluce
    Can a Windows Server be connected to an Active Directory domain without being a domain controller? Here's the scenario: I want to use Windows Server 2012 to run several virtual machines for testing our web application in a variety of environments. We have a corporate domain, and I'd like to use the corporate login (or at least a common login) on each of the virtual machines without necessarily having to get IT to set up each virtual machine on the corporate domain. Also, I need the server itself to be able to authenticate domain logins (the app uses domain login information for users to login). However, I absolutely do NOT want it to be a DC on the corporate network. Thus, my questions: Can a Windows Server be connected to an Active Directory domain without being a DC? Can a Windows Server authenticate users on another domain without being a part of that domain? Can a Windows Server be a domain controller in a small network (comprised of just the server and itself) and use the corporate domain's Active Directory for authenticating user logins to the server, the web app, and the virtual machines?

    Read the article

  • Connections to SSH and Samba suffer from heavy delay

    - by Till Helge Helwig
    There are a lot of questions about SSH connections being delayed, which usually can be fixed by disabling the DNS lookups. Unfortunately this doesn't seem to be my problem. Our development server is accessed via SSH and Samba. When opening a connection to the server (either SSH or Samba) it takes a very long time. Accessing a Samba share via Windows is basically impossible because there is a timeout. Using smbclient works, but takes ages. When opening a SSH connection I get immediately prompted for the password and after hitting Enter the terminal instantly shows the MOTD. Afterwards it takes about a minute for the prompt to appear. I watched the load of the server while connecting via SSH and Samba and could not find anything out of order. There is nothing out of the ordinary running and hogging up memory and CPU or something. I have no clue where this delay might come from. I already tried UseDNS no in sshd_config and proxy_dns = no in smb.conf, but to no avail. Any idea about what might cause this would be greatly appreciated!

    Read the article

  • Webcam security camera software that runs as a service

    - by hurfdurf
    I've been looking for Windows webcam software that will run as a Windows service without any user login. The goal is to use the webcam as a cheap security camera and log the results to secure networked storage (windows share, not FTP). The requirements are: Motion detection Video capture Runs as a service (should start recording immediately after reboot) Nice to have: Round-robin storage, e.g. 10Gb limit, oldest files overwritten/deleted when space gets low I've read the other webcam questions but still haven't stumbled across anything suitable. Evaluations thus far: Title MotionDetect Service Snapshots Video SpaceLimit License Yawcam Yes Yes Yes No No GPL WebCam ZoneTrigger Yes No Yes Yes No Commercial Dorgem Yes No Yes Yes No GPL AbelCam Yes No Yes Yes No Commercial Logitech Yes No Yes Yes No Paired with camera IspyConnect Yes No Yes Yes Yes Free SecureCam (SourcefoYes No Yes Yes No GPL AbelCam Yes No Yes Yes No Commercial Active WebCam Yes Yes(?) Yes Yes Volume Free Commercial WebCam Surveyor Yes No Yes Yes No Commercial WebCamsPy NA NA NA NA NA GPL Camera: Logitech Webcam Pro 9000 Windows 7 32-bit WebCamsPy failed to initialize so couldn't be tested So far, the contenders: Active Webcam comes the closest, and claims to run as a service, but i haven't been able to get it to record after a cold boot even though a service is running. Yawcam can be set up as a service but doesn't record video. IspyConnect has exactly the type of space limit I want and looks great, but doesn't run as a service (seems also to be a bit of a cpu hog) Any other suggestions? I'm locked into Windows so can't use linux Motion, which looks almost perfect. Any pointers to rich Windows webcam/motion detection libraries out there that could easily be turned into a command line program would also be appreciated.

    Read the article

  • explanation of RAM specs, and what do I need for a Gaming rig

    - by ewok
    I am looking into upgrading my custom built PC's RAM. I use the machine mostly for gaming, but I don't really know a ton about RAM, so I wanted to ask a few questions. The research I've done tells me there is a negligible increase in speed for anything above 1600 MHz. is this true or is it worth the extra money to go higher? Other than drawing more power from the PSU, is there any real difference in performance with different voltages (1.5V vs 1.65V)? most of the kits I've found in the 2x4 1600 range have a CAS latency of 9 and timing of 9-9-9-24. For a significant increase in price (usually about 1.5x), I can get either 8 or 7 and lower timing. Is it worth the cost? What I am looking for here is someone to give a good explanation of what the different specs represent, and how that relates to the performance of the machine. Specifically, I'm looking for what specs I need to focus on for a good gaming rig. I am NOT looking for a "buy this, it's the best RAM" without an explanation of why. The information will be much more valuable as it will allow me to make my own informed decision. As they say, give a man a fish, he'll eat for a day. teach a man to fish, and he'll eat for the rest of his life.

    Read the article

  • Which revision control system for single user

    - by G. Bach
    I'm looking to set up a revision control system with me as a single user. I'd like to have access (read and write) protected using SSL, little overhead, and preferrably a simple setup. I'm looking to do this on my own server, so I don't want to use the option of registering with some professional provider of such a service (I like having direct control over my data; also, I'd like to know how to set up something like that). As far as I'm aware, what kind of project I want to subject to revision control doesn't really matter, but just for completeness' sake, I'm planning on using this for Java project, some html/css/php stuff, and in the future possibly as a synchronizing tool for small data bases (ignore that later one if it doesn't fit in with the paradigm of revision control). My questions primarily arise from the fact that I only ever used Subversion from Eclipse, so I don't have thorough knowledge of what's out there, what fits better for which needs, etc. So far I've heard of Subversion, Git, Mercurial, but I'm open to any system that's widely used and well supported. My server is running Ubuntu 11.10. Which system should I choose, what are the advantages of the respective systems, and if you know of any particularly useful ones, are there tutorials regarding the setup of the system I should choose that you could recommend?

    Read the article

  • NFS-shared file-system is locking up

    - by fredden
    Our NFS-shared file-system is locking up. Please feel free to ask any questions you feel relevant. :) At the time, there are a lot of processes in "disk sleep" state, and the load averages on our machines sky-rocket. The machines are responsive on SSH, but our the majority of our websites (apache+mod_php) just hang, as does our email system (exim+dovecot). Any websites which don't require write access to the file-system continue to operate. The load averages continue to rise until some kind of time-out is reached, but for at least 10-15 minutes. I've seen load averages over 800, yet the machines are still responsive for actions which don't require writing to the shared file-system. I've been investigating a variety of options, which have all turned out to be red-herrings: nagios, proftpd, bind, cron tasks. I'm seeing these messages in the file server's system log: Jul 30 09:37:17 fs0 kernel: [1810036.560046] statd: server localhost not responding, timed out Jul 30 09:37:17 fs0 kernel: [1810036.560053] nsm_mon_unmon: rpc failed, status=-5 Jul 30 09:37:17 fs0 kernel: [1810036.560064] lockd: cannot monitor node2 Jul 30 09:38:22 fs0 kernel: [1810101.384027] statd: server localhost not responding, timed out Jul 30 09:38:22 fs0 kernel: [1810101.384033] nsm_mon_unmon: rpc failed, status=-5 Jul 30 09:38:22 fs0 kernel: [1810101.384044] lockd: cannot monitor node0 Software involved: VMWare, Debian lenny (64bit), ancient Red Hat (32 bit) (version 7 I believe), Debian etch (32bit) NFS, apache2+mod_php, exim, dovecot, bind, amanda, proftpd, nagios, cacti, drbd, heartbeat, keepalived, LVS, cron, ssmtp, NIS, svn, puppet, memcache, mysql, postgres Joomla!, Magento, Typo3, Midgard, Symfony, custom php apps

    Read the article

  • Distributed storage and computing

    - by Tim van Elteren
    Dear Serverfault community, After researching a number of distributed file systems for deployment in a production environment with the main purpose of performing both batch and real-time distributed computing I've identified the following list as potential candidates, mainly on maturity, license and support: Ceph Lustre GlusterFS HDFS FhGFS MooseFS XtreemFS The key properties that our system should exhibit: an open source, liberally licensed, yet production ready, e.g. a mature, reliable, community and commercially supported solution; ability to run on commodity hardware, preferably be designed for it; provide high availability of the data with the most focus on reads; high scalability, so operation over multiple data centres, possibly on a global scale; removal of single points of failure with the use of replication and distribution of (meta-)data, e.g. provide fault-tolerance. The sensitivity points that were identified, and resulted in the following questions, are: transparency to the processing layer / application with respect to data locality, e.g. know where data is physically located on a server level, mainly for resource allocation and fast processing, high performance, how can this be accomplished? Do you from experience know what solutions provide this transparency and to what extent? posix compliance, or conformance, is mentioned on the wiki pages of most of the above listed solutions. The question here mainly is, how relevant is support for the posix standard? Hadoop for example isn't posix compliant by design, what are the pro's and con's? what about the difference between synchronous and asynchronous opeartion of a distributed file system. Though a synchronous distributed file system has the preference because of reliability it also imposes certain limitations with respect to scalability. What would be, from your expertise, the way to go on this? I'm looking forward to your replies. Thanks in advance! :) With kind regards, Tim van Elteren

    Read the article

  • Adjust output Brightness/Gamma/Colors in Gnome

    - by Mikee
    We have a desktop system running Ubuntu 8.04.4, and it is connected to a standard desktop LCD monitor. Unfortunately, in 8.04.4, the brightness of the image is cranked way up. It appears to be a graphics driver issue. Unfortunately, installing a newer GPU driver for this Intel GPU is very difficult to do. So, I am looking for a software (or config file?) solution to achieve this. Note: Ubuntu 9.10 and higher do not exhibit this issue, so this is not a hardware problem. Note: VNC-ing to this machine from another does not exhibit this issue either. Also, I installed "DisplayCalibrator.app", and it does not work very well (the app comes up, but the contents of the window are blank). Is there anything that I can add to the xorg.conf file to correct this issue? Also, this solution: http://superuser.com/questions/96539/adjust-contrast-and-brightness-in-ubuntu did not resove my issue. Thank you all for the help!

    Read the article

  • Faster, secure, protocol/code required for long-distance transfer.

    - by Chopper3
    I've ran into a problem and I'm looking for a new secure protocol/client/server that's faster over a 1Gb/s fibre link - let me tell you the story... I have a pair of redundant, diversely-routed, 1Gb/s links over a distance of around 250 miles or so (not dark fibre but a dedicated point to point link, not a mesh). At the 'client' end I have a HP DL380 G5 (2 x dual-core 2.66Ghz Xeon's, 4GB, Windows 2003EE 32-bit), at the 'server' end I have a HP BL460c G6 (2 x quad-core 2.53Ghz Xeons, 48GB, Oracle Linux 5.3 64-bit). I need to transfer around 500 x 2GB files per week from the client to the server machines per week - but the transfer NEEDS to be secure. Using both iPerf or regular FTP I can get ~80MB/s of transfer pretty consistently, which is great. Using WinSCP or Windows SFTP I can't seem to get more that ~3-4MB/s, at this point the server's CPU is 3% busy while CPU0 of the client goes to ~30% utilised. We've tried editing various TCP window sizes with little success. Both ends are connected to quite low-usage Cisco Cat6509's with Sup720's. I can replace the client machine with a newer machine and/or move it to Linux - but this will take time. Clearly these single-threaded secure Windows clients are introducing too much latency doing their encryption. So a few questions/thoughts; Are there any higher performing secure protocols or client software for Windows that I could try? I'm pretty protocol-gnostic so long as it'll work between Windows and Linux. Should I be using hardware to do the encryption, either in the client or the network parts? If so what would you recommend? I'm not convinced that just swapping the server would be that much faster, the CPU was only at 30% but then again that's higher than I'd have expected given the load - moving to Linux at the client end may be a better idea but would be quite disruptive. Am I missing a trick? Thanks in advance.

    Read the article

  • Things to check for an internet-facing email server.

    - by Shtééf
    I'm faced with the task of setting up a public-internet-facing email server, that will be relaying mail for all of our other servers in the network. While the software in itself is set up in few keystrokes, what little experience I have with managing an email server has thought me that there are tons of awkward filtering techniques employed by other email systems. Systems that my own server will inevitably interact with a some point. Hence, my questions: What things should be kept in mind and double checked when setting up an email server? What resources are available for checking if my email server is set-up correctly? I'm specifically NOT looking for instructions for any given mail server, such as Exchange or Postfix. But it's okay to say: “you should have X and Y in your set-up, because when talking to server software Z, it typically tries to weed out open relays by checking for these.” Some things I've discovered myself: Make sure forward and reverse DNS are set up. Mail servers tend to do a reverse lookup for the peer IP-address when receiving. Matching a reverse look up with a follow-up forward lookup is probably employed to weed out open relays run through malware on home networks. Make sure the user in the From-address exists. The From-address is easily spoofed. A receiving mail server may try to contact the mail server in the From-domain, and see if the From-user actually exists.

    Read the article

  • I cannot connect to home server after a few hours

    - by Iago
    I have an old PC and I decided to revive it. A LAMP (for my own use) and a P2P server (torrent and e2dk). My old PC is an AMD Athlon XP (1400 MHz) with 384 Mb of RAM First of all I installed Ubuntu Server 11.10, SSH, FTP, SAMBA and LAMP. With this configuration my home server works well, with no problem. Then I went to the P2P server and I tried rTorrent and then uTorrent Server Alpha. And here is my problem. After a few hours (maybe 10 hours, or maybe 30 hours) with the torrent app running (rTorrent or uTorrent) I lose the connection to my home server. That is, I cannot access via ssh, I cannot access the apache server, etc. but I can ping the home server. It seems that the server freezes and all I can do is reboot the server physically. So, I have two questions: What is the problem? and How can I solve it?

    Read the article

  • Give Access to a Subdirectory Without Giving Access to Parent Directories

    - by allquixotic
    I have a scenario involving a Windows file server where the "owner" wants to dole out permissions to a group of users of the following sort: \\server\dir1\dir2\dir3: Read & Execute and Write \\server\dir1\dir2: No permissions. \\server\dir1: No permissions. \\server: Read & Execute To my understanding, it is not possible to do this because Read & Execute permission must be granted to all the parent directories in a directory chain in order for the operating system to be able to "see" the child directories and get to them. Without this permission, you can't even obtain the security context token when trying to access the nested directory, even if you have full access to the subdirectory. We are looking for ways to get around this, without moving the data from \\server\dir1\dir2\dir3 to \\server\dir4. One workaround I thought of, but which I am not sure if it will work, is creating some sort of link or junction \\server\dir4 which is a reference to \\server\dir1\dir2\dir3. I am not sure which of the available options (if any) would work for this purpose if the user does not have Read & Execute permission on \\server\dir1\dir2 or \\server\dir1, but as far as I know, the options are these: NTFS Symbolic Link, Junction, Hard Link. So the questions: Are any of these methods suitable to accomplish my goal? Are there any other methods of linking or indirectly referencing a directory, which I haven't listed above, which might be suitable? Are there any direct solutions that don't involve granting Read & Execute to \\server\dir1 or \\server\dir2 but still allowing access to \\server\dir1\dir2\dir3?

    Read the article

  • Windows 8 using as a webserver

    - by Jason
    I have a few hobby websites that I currently host on CentOS 6. Apache, mail serving, PHP, MySQL nothing special. In the past I used Windows XP to do this same task, for years, and I was OK. I switched to Linux and for the last few years it has been such a pain. updates break, certain apps only support certain distros without compiling from source. It prevents me from working on my hobby sites more because I am always fixing something. With Windows I locked it down, I run a hardware firewall and packet analyser, kept up on updates and A/V and never had a problem. I dont allow RDC from outside the local LAN, no FTP open, run OpenSSH on an obscure port.. I am considering switching to Windows 8 (since it is a cheaper license now that Windows 7) and running apache, HMailServer, PHP, MySQL, just like my CentOS install. My questions: I am not familiar with Windows 8, can the above be done like XP? No new security restrictions or the OS preventing this from happening? The machine is a Athlon 64-bit X2 with 32GB of RAM. Will Windows 8 see all of the RAM? Technically the machine came with Windows 7, and there is a serial number on it but I am sure I wiped away the Windows 7 recovery partition when I switched to Linux....

    Read the article

  • Removing Paths/ Landing Pages From SharePoint Search Results

    - by j.strugnell
    Hi there, We've been asked by a client to remove a number of pages from being shown up in their public website search results page. I've been into the SSP and created Crawl Rules to remove these pages. All seemed to have worked ok but we have an issue in that landing pages are still showing up in their "www.domain.com/sitearea/" form but not in their "www.domain.com/sitearea/pages/default.aspx". For each of this type of page we have created one rule to "Exclude" the "aspx" path and another rule to include the "/" path but to "Follow links on the URL without crawling the URL itself". We tried adding rules to exclude the "/" format but that only resulted in all results underneath that being excluded. Does anybody know how to remove the "area/pages/default.aspx" and the "area/" pats from Search Results? I'm not sure if it's the "done thing" to ask 2 questions in one but this is in a similar vein so it should be ok. I was wondering if anyone knew of a tool (or if it is possible) to allow site admins to exclude pages from search results (not via SSP/Crawl Rules). I know they can do it at the site level but I was wondering if anything out there enabled this to be done at the page level through either Page or Site Settings?

    Read the article

  • Postfix + Exchange + ActiveDirectory; How to mix them

    - by itwb
    My client has got many sub-offices, and one head office. The headoffice has a domain name: business.com All users in the many sub-offices need to have a headoffice email address: [email protected] Anyone not in the head office will need the email forwarded to an external email address. All users in the head office will have their email delivered to Microsoft Exchange. Users are listed in Active Directory under two different OU's: HeadOffice or SubOffice. Is this something able to be configured? I've done some googling, but I can't find any examples or businesses set up this way. Edit: Postfix will accept all email, will need to determine to forward the email to an external account or alternatively have it delivered to MS Exchange. I've done some reading about MS Exchange and that you can 'mail-enable' contacts for forwarding - but I don't know if each AD account requires an Exchange CAL? The end goal is to forward email to external accounts to sub offices or accept email for head office. Maybe I don't need to worry about Postfix to perform this task..... http://www.windowsitpro.com/article/exchange-server-2010/exchange-server-licensing-some-of-your-questions-answered "What about client access licenses (CALs)? You need one CAL per user who will connect to Exchange. Although it might not be 100 percent precise, I prefer to think of it as one CAL per mailbox; there are exceptions for users outside your organization, automated tools that use mailboxes, and so on. Exchange doesn't enforce this limit, so it's on you to ensure that you have the correct number of CALs for the set of clients you support."

    Read the article

  • SSD for swap on Ubuntu server

    - by grs
    Currently I am reading SSD reviews and I wonder how much exactly I will benefit if I move the 24 GB swap from 7200rpm HDD to SSD. Does anyone implemented swap space on SSD? Is this generally good idea? On a side note: I read that ext4 has much better performance if the journal is on SSD. Anyone with such a setup? Thanks! Edit: Here I will answer the questions posted: Occasionally, relatively rare I am hitting the swap. I know what the swap is for and that is better to get more RAM. When the server begins to swap its performance degrades (not a surprise). The idea is if I have few memory hungry processes running, to improve the overall system performance at that time, using SSD for swap, instead of slower rotational media. At the end - I want to be able to login faster and check the server state during swapping, instead of waiting on the login prompt. And of what I see SSD is cheaper per GB than RAM. Would I have better server performance during swapping (as rare it is) using SSD compared to HDD? Where 10k or 15k rpm HDDs would rate in this scenario? Thank you all for your quick and prompt answers!

    Read the article

  • How can I setup nginx to serve virtualhosts with rails(unicorn/passenger) and php-fpm

    - by NewAlexandria
    I would like to serve multiple sites on one instance. I install nginx, php-fpm, and a rails app. I use sites like this to guide me. I configure php-fpm to listen to a local socket listen = /var/run/php-fpm/php-fpm.sock I configure ngnix with multiple hosts: include /etc/nginx/conf.d/*.conf I have several site php conf files like /etc/nginx/conf.d/site1.conf server { listen 80; server_name site1.com www.site1.com; root /var/www/site1; location / { index index.html index.php; } location ~ \.php$ { fastcgi_pass unix:/var/run/php-fpm/php-fpm.sock; fastcgi_index index.php; include fastcgi_params; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_param SCRIPT_FILENAME $document_root/$fastcgi_script_name; } } and rails site conf files like upstream rails { server 127.0.0.1:3000; } server { listen 80; server_name site2.com www.site2.com; root /var/www/site2; location / { proxy_pass http://rails; proxy_set_header X-Forwarded-For $remote_addr; proxy_set_header Host $host; proxy_set_header X-Url-Scheme $scheme; } } I have a unicorn rails server running via rails s -p 3000 Yet, no sites come up for either site1.com or site2.com. I can get to the rails site at www.site2.com:3000 What is wrong? I've spent 2 days (nearly 30hr) trying many different blogs, SO / SF questions, etc. Please share your insight or answer. edit 1: No log entries are created when I try to visit either site. It's like the requests never come in.

    Read the article

< Previous Page | 404 405 406 407 408 409 410 411 412 413 414 415  | Next Page >