Search Results

Search found 15144 results on 606 pages for 'fixed width'.

Page 410/606 | < Previous Page | 406 407 408 409 410 411 412 413 414 415 416 417  | Next Page >

  • Ubuntu networking issue: two specific machines cannot browse web while connected to network at the same time.

    - by jensendarren
    I have setup a secure wireless network which works very well except for two laptops running Ubuntu 10.10 that can't access the Internet via a browser at the same time. They can both ping sites, wget sites, use skype but when using a browser the page never loads (in Firefox the status bar just sits there saying "Connecting" until it times out.) Here is what we have tried so far (nothing has fixed this issue): OpenDNS Restart networking services Using wired connection rather than wireless Removing all other nodes from the network except the two machines that have this issue Swapped out the router Factory reset the router Reformatted one of the machines and re-installed Ubuntu 10.10 Other things that we have checked: The two machines can connect simultaneously without any issues to other wireless networks in different locations (say in an Internet Cafe or another office) The two machines have unique IP addresses The two machines have unique MAC addresses The two machines can communicate on the network using Skype, wget, ping etc We are not using a proxy on either machine FYI: I have attached output from wireshark. For the test we turned both machines on and pointed them both to the same website. The content loaded on one and not the other. Here is the output from wireshark- (speedyshare.com/files/26228631/machine_output_1 && speedyshare.com/files/26228649/machine2). As you can see the first one worked, the second one didn't. I don't fully understand the output and would appreciate if someone could shed some light on what might be causing this and how we can fix it! Many thanks! Darren

    Read the article

  • IP6 seems to be enabled - How do I configure it without interfering with IP4?

    - by Mister IT Guru
    I noticed that some of my Centos boxes have IP6 enabled, and seem to have addresses. I have no problem with this, but I would like to get a handle on it, and even connect to them using IP6. This would really help if for any reason DHCP has a hiccup. But I'm a bit lost as to where the configuration on my CentOS box is. (I am also on google researching this, but I like server fault! :) ) I am hoping that I would be able to log into this via the VPN because every now and then that DHCP device has a bad morning, and needs to be restarted. (I'm also looking into this issue, but someone else handles that, management separation gone mad!) It's a remote client, so it would be a lot easier for me to connect to these systems which seem to self configure, to use that as a pivot via ssh tunnels to get to other remote devices to continue to manage them, while out main route is fixed. I guess, my questions are How can I configure IP6 without interfering with IP4, and On CentOS, can I influence this auto configuration I seem to be seeing?

    Read the article

  • Orphaned SQL Recordsets/Connections with IIS

    - by Damian
    I have an IIS 6 site running on Windows 2003 Server x86 with MS SQL2005 Enterprise edition running ASP Classic (no choice). The site runs very fast with about 8000 page views per hour. All of my SQL tables are indexed and I have used the profiler to check my queries, the slowest of which is only about 10-15ms. I have autoshrink disabled, autogrow is set to 250mb, database is 2gb with 800mb of free space. My problem is that every now and then the site will slow to a crawl for no reason. Pages that just have a simple 'connect to databse and increment a hit counter' work ok, but more SQL intensive pages that normally execute in about 60ms take 25,000ms to run. This happens for about 30 seconds and then goes away. I was having an issue with orphan recordsets and connections due to the way I was releasing them. I have fixed this up and the issue is much better, but I am still getting them. Is there a way with permon, etc. to track when SQL Server or Windows closes these Orphan connections? At least if I can monitor the issue I will know if I am making progress or if I am even looking at the right things. Is there anything else I might be missing? Thank you!

    Read the article

  • Lenovo System Update Breaks Windows Live

    - by wolfvilleian
    Hey everyone, I've been racking my brain (and fingers from typing) trying to solve this issue to no avail. I have a Lenovo computer and I install their system update tool to install all my missing drivers. However after this tool is installed Windows Live 2011 breaks, it will no longer sign in giving error number 8e5e0247 all the solutions online haven't helped. It appears that a language setting somewhere gets set to en_ms, and I'm en_ca. My computer is running Windows 7 x64. When i try to sign onto messenger it gives an error that (with some research) means your locale or language is not supported, I've searched my computer for any reference to en_ms but find none. Also a few other things seem to have broken, When a UAC box comes up it is no longer able to identify the publisher of anything, and also the indexing service does not work (I'm not sure if the indexing issue is related, but the UAC issue happened right after installation), I had this issue before but I don't remember how I fixed it, I believe it had something to do with environmental variables. When it goes to sign in it gets as far as the "Loading contacts" then stops and goes back to the sign in screen. Has anyone seen this before? Thanks

    Read the article

  • Xen Bridge only working when IP Assigned

    - by m.sr
    Hey! Just had an (in my sense) obscure situation. I have a Xen Server with bridged networking. Everything works fine since month. A while ago i configuresd a second bridge. only some DomUs get an channel on this bridge - my Dom0 doesn't need to / should'nt use this bridge. So just 5 minutes ago while rebooting the xen host (because of an other problem with the UPS) i decided to removed the fixed ip from the the interface of the Dom0 which belongs to the second bridge. So after reboot i noticed that none of the interfaces on the second bridge is available. I couldn't find a problem. Everything was just like before the reboot, except the interface of the Dom0 had no IP address. After a while i tried to give the DomO interface of this bridge an IP again and ... BOOM ... everything is up and running again! WTF? Why is it important to have the interface of a bridge configured in the Dom0? Even when confiugured 'wrong' (complitely different netowkr settings as the network really hanging on the bridge) everythjing works fine ... I don't get it. Could please someone explain? Tnaks a lot!

    Read the article

  • How to make project auto-estimate duration based on work?

    - by Bruno Brant
    This one has bothered me for a long while. I like to do estimates thinking on how much time a certain task will take (I'm in TI business), so, let's say, it takes 12 hours to build a program. Now, let's say I tell Project that my beginning date is today. If I allocate one resource to this task, it means that the task will last 1,5 days, implying that it will end tomorrow. But right now, that is not what it's doing. I say that the task will take 1 hour, and when I add a resource to it, it allocate the resource at [13%] basis, which means that the duration is still fixed... project is trying to make the task last for a day. I have, on many occasions, accomplished this. What I do is build a plan based on these rough estimates for effort, then I allocate tasks to resources. Times conflict, so I level resources and then Project magically tells me how long, in days, will it take. But every time I have to start estimating again, I end up having trouble on how to make project work like that.

    Read the article

  • Why does Facebook Chat through XMPP protocol on Pidgin Portable not authorize?

    - by Sara Neff
    I heard you can use facebook chat on desktops now. Thats awsome! What i didn't hear is that it is a pain in the butt! Not awsome! I've followed six nearly identical sets of instructions from six different websides, including the one that facebook generates for you, to get facebook chat connected through Pidgin. Its the latest portable version, so from what i hear the plugin is out of the question. Whenever I go to try and connect i get a message saying "Not Authorized" and buttons to either modify the account info, or retry. NOTHING i have done has fixed this, and I can't find anything remotely usefull anywhere. I am running windows xp, and running pidgin (portable) off of a flash drive. Someone please tell me what i have to do. I read about authorizing the chat on my actual facebook page. I'd have tried that if i could find out how to do it, but if its there they hid it good. HELP?!

    Read the article

  • Using VMware Guest OS to enable Host OS to ssh to remote network

    - by Reuben L.
    Basically I have an issue because my host OS is 64-bit Linux Mint (Ubuntu derived) and it doesn't seem to be compatible with the Juniper Network Connect that is used by the network at my workplace. Thus, I am unable to ssh from terminal to the network. I can't make changes to the workplace network either so that leaves me with looking for solutions on my end. The main reason for me to access the network from home is to check on my running processes or to issue more commands to a few workstations. Putty is the desperate choice I usually make but it means I have to reboot to Windows and also have limited control. I've tried several other methods and they have all failed. Recently, I setup a VM with Windows 7 as the guest OS. Now half my problems are fixed as I don't have to physically reboot the system - I just have to engage Juniper Network Connect on the VM. However, I would still like to use my Linux terminal to ssh to the network. It sounds plausible that I could somehow manipulate ports to connect to the remote network from the host OS tunneled through the guest OS, but I really have no clue how to do so... Can anyone help?

    Read the article

  • Apache can't get viewed from outside of my LAN

    - by Javier Martinez
    I fixed it in PORTS TRIGGER menu of my router. Thanks you anyway I have a weird problem related with (i think) my cable-router and my configured vhosts in Apache2. The point is I can't access from outside of my LAN to any of my configured vhosts if I set the http port of Apache to 80 and i add a NAT rule for it. Otherwise, if I set my Apache port to 81 (or any else) with its respective NAT rule on my router it works. My router is an ARRIS TG952S and I am using Apache/2.2.22 (Debian) ports.conf NameVirtualHost *:80 Listen 80 vhost1.mydomain.net.conf <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName vhost1.mydomain.net ServerAlias vhost1.mydomain.net www.vhost1.mydomain.net vhost2.mydomain.net.conf <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName vhost2.mydomain.net ServerAlias vhost2.mydomain.net www.vhost2.mydomain.net DNS records (using FreeDNS) are: mydomain.net --> pointing to another server vhost1.mydomain.net --> pointing to my server vhost2.mydomain.net --> pointing to my server iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination fail2ban-apache-noscript tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 80,443 fail2ban-apache tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 80,443 fail2ban-ssh tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 22 Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain fail2ban-apache (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-apache-noscript (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-ssh (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Thanks you

    Read the article

  • Chrome pop-up blocker fail?

    - by Count Zero
    I have this problem since just a few days. I've been a heavy Chrome user for several years, but it never happened before: Sometimes absolutely uncalled for pop-ups appear, when I click something absolutely legit. It seems to happen at a very precise rate of two pop-ups every hour or so. The pop-ups are not very varied, it seems to be a fixed set of some 4-5 ads. At first I thought I caught some malware, but after a full scan with Malwarebytes Anti-Malware, I found absolutely nothing. In addition the problem exists only with Chrome. When I use Firefox, this never ever happens. What is even more puzzling is that it happens on both of my rigs and started on the same day. I have a removable storage that I dock to both of them and access one machine from the other via RDP, but still... It seems this is a problem that others face too. See this Google forum and here. Could it be that the latest Chrome build is just acting up? (Just in case it matters: I run Chrome version 24.0.1312.57 m on Win 7.)

    Read the article

  • Unable to ssh to a Linux VM after a day

    - by jogabonito
    I have a machine running 4 VMs on it. There is one Fedora VM which is causing me some trouble. The IPs of the VMs are something like 10.100.100.* I have a Windows PC which is in the same network. It has an IP 10.100.25.77. When I reboot the Fedora VM, I am able to ping it from my Windows PC as well as use putty to ssh to it. The next day, I cant ping it or ssh from my Windows PC. However I can ping and ssh to the other VMs on the machine. If I ssh to one of the other VMs, I can ping and ssh to the Fedora VM. Next if I restart it, things get back to normal and I can access it without any issues. The IP of the VM doesn't change after rebooting and it is statically assigned I would like to know what is causing this and how to get it fixed. As a last resort, I am thinking of running a cron job to restart the VM every night, it is not a critical server, but will be generally used occasionally in the day time.

    Read the article

  • How can I move linked Word/Excel files without breaking the links under Windows 7?

    - by DOUG NEEDHAM
    I currently operate under Windows XP and have multiple links between my Word and Excel files. I have to upgrade to Windows 7. When the .doc and .xls files are converted to .docm and .xlsm, respectively, the links no longer work. The Word document is still attempting to point back to the old .xls file rather than the new file. Also, creating new links between Word and Excel within Office 2010 doesn't seem to work. I create the new link, switch it from "Auto" to "Manual" and everything works fine. But when I copy the files to another folder, the Word document is still trying to link to the file in the previous folder rather than the new folder. This always worked in Windows XP. I've been using linked Word/Excel documents for 10+ years and have never really had a problem. I'm very careful to maintain Word and Excel filenames when moving the files to a new folder. The process has always been to 1.) move the files, 2.) update the links, 3.) rename the files, and 4.) update the links again. It's my understanding that under Windows XP, links between Word and Excel are relative. But under Windows 7 (and Office 2010?), those same links become fixed.

    Read the article

  • Messed up partitions... system will not boot!

    - by someguy
    I did a really dumb thing. cfdisk threw an error at me saying "FATAL ERROR: Bad primary partition 3: Partition ends in the final partial cylinder", so I installed Partition Table Doctor to see if I could fix the problem. When the program started up, it told me there were problems with my partitions, and asked if I wanted them fixed (cannot remember real message, but I believe it had something to do with the cylinder boundaries), so, blindly, without thinking of the consequences, I did. Now, my system will not boot. I tried booting from the Windows 7 installation CD. I went to install a fresh copy, but it said that "No drives were found". I then opened up diskpart. According to diskpart, there is only one partition, containing one volume, assigned the letter "C". Before, I had four partitions! It is also saying that the file system is RAW. Is there any way I can fix this? I have important data that I do not want to lose. Later on... I tried fdisk with the option -l, which lists the partition table(s), and this is what I got: Ignoring extra extended partition 4 Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 64 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x163df116 Device Boot Start End Blocks Id System /dev/sda1 6 18 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 18 7851 62918572+ 7 HPFS/NTFS /dev/sda3 13073 30402 139196416 f W95 Ext'd (LBA) /dev/sda3 13073 30402 139196416 f W95 Ext'd (LBA) /dev/sda3 13073 30403 139203193 7 HPFS/NTFS I don't know if this will help, but it's extra information, at least. Also, this is how I had my partitions: 40MB (Unallocated) 100MB (System Reserved) 60GB (Windows, C:) 40GB (Was reserved for secondary OS) ~132GB (Home, E:)

    Read the article

  • Ubuntu 10.10 forgets desktop theme.

    - by Marcelo Cantos
    I am running Ubuntu in VirtualBox (on a Windows 7 host). Several times now, the top-level menu bar, the task bar — and seemingly every system dialog — have forgotten the out-of-the-box "Ambiance" theme they conform to when I first installed the system. Window captions still preserve the theme, but pretty much nothing else does. I have searched high and low on Google for assistance with this problem. Everything I've found suggests either running some gconf reset or deleting .gconf* .gnome* and other similar directories. I have followed all this advice and nothing works. I still get a boring Windows-95-style gray 3D look and feel. On previous occasions, after much messing around I've given up and rebooted the VM instance, and been pleasantly suprised to see the original "Ambience" theme restored throughout the UI, but invariably it disappears again some time later, usually after a reboot, so I can never figure out what I did that broke it. Here's a sample from Ubuntu's site of what I want it to look like. And here's a screenshot of my system as it currently looks. Also note that my GNOME Terminals normally have a nice purple semi-translucent look, and as can be seen from the screenshot, they are now just a solid matt white. This last time (just this morning), trying numerous combinations all the usual tricks and rebooting several times hasn't fixed it, so here I am on SU wondering: How do I recover the out-of-the-box theme for my Gnome/Ubuntu desktop, noting that blowing away all config files — as suggested in many places online — fails to achieve this? EDIT: It might help to know that it seems to fail either after I resize the VM instance, forcing the Ubuntu desktop to resize itself, or after I play around with Compiz settings. I haven't been able to figure out which of these it is, and it could be neither. Given the amount of pain I have had to go through to get things back to normal (and given that I am at a loss as to how to do so), it has proven difficult to definitively isolate the cause.

    Read the article

  • What is causing ocassional white windows on my Mac?

    - by user63333
    Hello. I'm having a very strange problem with my Mac lately. When I'm working in an app and a new window pane or sheet is displayed, sometimes it comes up completely white. Once an app is having these problems, it will continue to bring up a blank screen for that particular window (although other windows work fine). After the app is relaunched, the window is fine again. What I'm noticing that's very strange is that although the interface turns completely white, the functions of the interface are still available. So I have to "navigate blindly" around the interface, until I can relaunch. This occurs throughout the operating system. Screenshots: This is what happened when I tried opening the File menu in Lightroom app. What happened to me on Lynda.com (in Firefox) after selecting the "Software..." dropdown. (All other dropdowns were fine. Reloading the page fixed it.) When I was decompressing a file, The Unarchiver launched and opened this white window. It still decompressed the file. This is what happened one time when I opened Finder (with TotalFinder) to my Downloads folder. This is something I've never seen before. This just started happening lately. What could be the problem? Thanks for your help. NOTE: since new users are not allowed to post images, just image blank white interface elements. And since new users also aren't allowed to post more than one link, here's the first screenshot:

    Read the article

  • Sudden problems with iptables not running

    - by Fourjays
    I've got a sudden issue with iptables not running on my CentOS 5.8/DirectAdmin XenVPS. All I have done today is install PHP APC and run an update (although I admittedly didn't pay much attention today - I usually do). Iptables has been running fairly smoothly since I installed it over 6 months ago. Basically when I try to run iptables -L it tells me: iptables v1.3.5: can't initialize iptables table `filter': iptables who? (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. I've looked around and tried a few things and it appears that maybe my kernel doesn't have the modules loaded? I've been reading this and tried the two commands they suggest to no avail. Except there does appear to be a mismatch on one bit of output: -bash-3.2# cd /lib/modules -bash-3.2# ls 2.6.18-194.32.1.el5xen 2.6.18-238.5.1.el5xen 2.6.18-274.7.1.el5xen 2.6.39.1-cs-domU 2.6.18-238.12.1.el5xen 2.6.18-238.9.1.el5xen 2.6.37.2-cs-domU 3.0.1-cs-domU -bash-3.2# depmod -a WARNING: Couldn't open directory /lib/modules/2.6.18-274.18.1.el5xen: No such file or directory FATAL: Could not open /lib/modules/2.6.18-274.18.1.el5xen/modules.dep.temp for writing: No such file or directory Does this mean the versions are out of sync? If so, what are my next steps to getting this fixed? As you can probably tell I am still learning how to manage my server so please be very clear in all advice. Many thanks :)

    Read the article

  • ORA- 01157 / Cant connect to database

    - by Tom
    Hi everyone, this is a follow up from this question. Let me start by saying that i am NOT a DBA, so i'm really really lost with this. A few weeks ago, we lost contact with one of our SID'S. All the other services are working, but this one in particular is not. What we got was this message when trying to connect ORA-01033: ORACLE initialization or shutdown in progress An attempt to alter database open ended up in ORA-01157: cannot identify/lock data file 6 - see DBWR trace file ORA-01110: data file 6: '/u01/app/oracle/oradata/xxx/xxx_data.dbf' I tried to shutdown / restart the database, but got this message. Total System Global Area 566231040 bytes Fixed Size 1220604 bytes Variable Size 117440516 bytes Database Buffers 444596224 bytes Redo Buffers 2973696 bytes Database mounted. ORA-01157: cannot identify/lock data file 6 - see DBWR trace file ORA-01110: data file 6: '/u01/app/oracle/oradata/xxx/xxx_data.dbf' When all continued the same, I erased the dbf files (rm xxx_data.dbf xxx_index.dbf), and recreated them using touch xxx_data.dbf. I also tried to recreate the tablespaces using `CREATE TABLESPACE DATA DATAFILE XXX_DATA.DBF` and got Database not open As I said, i don't know how bad this is, or how far i'm from gaining access to my database (well, to this SID at least, the others are working). I would imagine that a last resource would be to throw everything away, and recreating it, but I don't know how to, and I was hoping there's a less destructive solution. Any help will be greatly appreciated . Thanks in advance.

    Read the article

  • Terminal emulation has stopped working. Garbage escape chars

    - by oligofren
    To enable me to do some remote administration of our servers I started using a terminal emulation program called TouchTerm Pro on my iPhone. While not the smoothest experience, it has allowed me to leave my computer behind when going out of town, which makes the slightly painful experience worthwhile. As of late, the app unfortunately no longer works. Pressing up and down keys after logging on via ssh gives me garbage like ^[[A and ^[[B. Combinations with Ctrl - like you can see in the video - no longer works either. Writing full command lines and executing by the enter key works though. Being able to search my bash history was the difference between a usable app and endless frustration, so getting it to work is essential. The app has (of course) met its end of life, not getting updated anymore. I am not quite sure, which side (client or server) that has to be "fixed"/hacked to make the control sequences work again. But is there something I can do to make it work as intended? You can see a video of TouchTerm in operation here.

    Read the article

  • How do you gracefully upgrade mission critical systems to wildly disparate systems?

    - by Ernie
    In the span of the 12+ years of my career, I have yet to overcome this hurdle and I suspect the answer simply isn't easy or even possible, so I ask everyone here for their experience. Say that you're running into egregious problems that can only be fixed by moving from one platform to another - either from making a mistake in choosing the platform that was chosen years ago, or simply growing beyond what the system was originally designed for. You know for certain that the cruft that has built up over time will invariably mean that it will be nearly impossible to test for all the things that will certainly lead to tech support hell - which we all know leads to the loss of customers. Not that customers aren't already complaining about the egregious problems that already exist! The best possible way that I've discovered so far is to maybe devise a plan for the changeover, test it on a few clients, test it on a dozen clients, test it on a hundred clients, then finally finish the changeover for everyone and pray that you've worked out all the bugs with those first hundred and twenty, and that the animal by-products will not hit the ventilation system in the most spectacular fashion possible. However, that doesn't mean that it won't anyway. So say that you're moving from Exchange to Exim (or even just Sendmail to Exim). How do you handle it?

    Read the article

  • College network - can I point non-domain student computers to our SUS server?

    - by Joel Coel
    Since I started here 3 months ago, one of the things that's really bothered me about the way this network is setup is something that shows up on the daily bandwidth consumption report. I get a list of top-visited sites by hits and by size, and invariably the top site (to the point that it's bigger than all the other top sites combined) is au.download.windowsupdate.com. We're pulling in ~30GB/day in windows updates. This is every day, not just after a patch Tuesday. After a patch day, it jumps closer to 40GB for a couple days. The key here is that almost none if it is by machines that I'm responsible for. My machines are for the most part fully patched, and when they're not they'll pull from a SUS server, so new updates are downloaded only once. It used to be closer to 50GB/day because most of the machines in our computer labs use DeepFreeze and weren't applying updates correctly, but that's fixed now. So the problem is definitely student-owned machines in the dorms, some of which are re-downloading the same updates in background each day, over and over. I'd love to have these machines start pulling from our SUS server. Then, if they don't ever actually install them at least they're not leeching bandwidth from our public internet connection. Any ideas on how to resolve the situation?

    Read the article

  • Document Map in MS Word 2007 going bonkers

    - by rzlines
    I'm working on a large project report in Microsoft Word 2007 and have been using the document map to generate the index. I have been carefully selecting the headers that need to be added to the document map but I saved the document and opened it up today to work on it - the document map has added whatever it pleases there. This is a temporary fix from a post that I found after extensive searching that works, but when I save and close the document and open it up again I face the same dilemma: I have noticed that when Word stuffs up the document map after opening the file, I can undo this by using the UNDO button. Word calls it ’Autoformat’. I have also fixed a file that has had the document map screwed permanently (i.e saved with it) by selecting all (CTRL+A),selecting the PARAGRAPH drop down menu in the HOME TAB and in the OUTLINE drop down box, selecting ’Body Text’. This removed all the problems and did not seem to affect my outline level paragraph headings. This is also another temporary fix but I have to be on my toes not to let Word auto format at the start of the document. I also can't afford to entirely turn off auto format as I need it. I’ve solved this problem for me. When you open the file, a progress bar at the bottom first says Opening (ESC to Cancel) and then it says Word is formatting the document (ESC to Cancel). If I cancel the second process, TOC fine. No cancelling, TOC screwed. Can anyone work out how to switch off the autoformatting? This is the post in which i found for the temporary fix

    Read the article

  • What is going on when I can't access an SMB server share (not accessible error) until I run cmdkey to delete the credential?

    - by Warren P
    I have a network connection share issue. The first connection works, and seems to stay connected for at least a few hours. However, after each time my windows 7 PC reboots, it can no longer form a network connection to the shared folder, nor browse to it, until I not only unmap and remap the mapped drive, but also, I have to use cmdkey to delete the stored credentials like this: cmdkey /delete:Domain:target=HOSTNAME My work PC is on a domain, and I am not the IT administrator, but I'm curious if there is anything I can do to investigate this issue. Any settings in registry or group policy that I could examine to see why the first connection works, but each subsequent attempt (once a stored credential exists) to browse or use the connection, fails with a connection error saying it is "not accessible", like this: I do not even get any error until at least several minutes go by. THe first thing I see is a window frozen and empty, and then I get this error: This has happened when connecting to a share on a DROBO device, and on a share which is not on the domain, but which was a Microsoft Home Server. I wonder if there's something broken in WIndows 7 professional with regards to connecting to non-domain shares when an active directory domain controller exists, and a particular workstation is joined to a domain? The problem only occurs if I click "remember credentials". It is not fixed by any amount of working with net use. Usingcmdkey to delete all stored credentials for the host is the only way to get back in, and it affects all non-domain shared folders. Update I'm hoping there are some registry locations I could check that could be misconfigured in some way that might explain why SMB/CIFS stored credentials for non-domain systems seem to be auto-invalidated in this weird way. Knowing how whacko Microsoft Windows domain and security handling is sometimes, this could be some kind of stupid "feature".

    Read the article

  • Apache using 100% CPU, once again

    - by CBenni
    Recently, apache2 started using 100% of CPU power: top gives me From other, similar threads, I took the tip to use mod_status. Aside from HUGE amounts of NULL requests, it gives: CPU Usage: u2.16 s1.32 cu0 cs0 - .0835% CPU load 1.2 requests/sec - 17.6 kB/second - 14.6 kB/request 8 requests currently being processed, 42 idle workers The access and error logs do not show anything surprising or intriguing at all. Note the .8% CPU usage. Another tip was to use strace: root@server:~# strace -p 1956 Process 1956 attached - interrupt to quit restart_syscall(<... resuming interrupted call ...> And remains like this for at least half an hour, without producing any additional output. Restarting apache fixed the problem for less than a second The server runs a few custom python scripts aswell as a django-powered website on apache2 (up-to-date), but even turning the scripts off (or not having them active in the first place) did not change anything. After I stopped apache and powered my server off, powered it on a few minutes afterwards and restarted all my services, the CPU usage remained low for several hours, just in order to pop up again randomly (?) The DigitalOcean CPU stats on my server are: You can see how the CPU usage was super high for almost half a day until I restarted the bot - just to remain stable for several hours and then pop up again. I am completely at a loss of words and don't know what I could do to find out what piece of my code is giving me these problems or if apache itself is the cause... Therefore I would greatly appreciate any hints to the questions: What else can I try to do? Which things might I not have checked? Is this definitely in my own code? How do you find what part of python code crashes an app via a infinite loop or similar?

    Read the article

  • make file readable by other users

    - by Alaa Gamal
    i was trying to make one sessions for my all subdomains (one session across subdomains) subdomain number one auth.site.com/session_test.php session_set_cookie_params(0, '/', '.site.com'); session_start(); echo session_id().'<br />'; $_SESSION['stop']='stopsss this'; print_r($_SESSION); subdomain number two anscript.site.com/session_test.php session_set_cookie_params(0, '/', '.site.com'); session_start(); echo session_id().'<br />'; print_r($_SESSION); Now when i visit auth.site.com/session_test.php i get this result 06pqdthgi49oq7jnlvuvsr95q1 Array ( [stop] => stopsss this ) And when i visit anscript.site.com/session_test.php i get this result 06pqdthgi49oq7jnlvuvsr95q1 Array () session id is same! but session is empty after two days of failed trys, finally i detected the problem the problem is in file promissions the file is not readable by the another user session file on my server -rw------- 1 auth auth 25 Jul 11 11:07 sess_06pqdthgi49oq7jnlvuvsr95q1 when i make this command on the server chmod 777 sess_06pqdthgi49oq7jnlvuvsr95q1 i get the problem fixed!! the file is became readable by (anscript.site.com) So, how to fix this problem? How to set the default promissions on session files? this is the promissions of the sessions directory Access: (0777/drwxrwxrwx) Uid: ( 0/ root) Gid: ( 0/ root)

    Read the article

  • Linux usd disk just create sg device

    - by MTilsted
    I have a Corsair R60 ssd disk which is a disk with both sata and usb connectors. But the usb thing seems to be a bit non-standard, or maybe its just my fedora linux. When I insert the disk using a usb cabel to a running Fedora 14 linux system, a device called /dev/sg3 is added but that is all. No new /dev/sd* device is created so I can't mount the disk. If I look at cat /proc/scsi/sg/device_strs I get ATA Hitachi HTS54321 FB2O HL-DT-ST DVDRAM GSA-T50N RP05 Seagate Desktop 0130 Corsair CSSD-R60GB2 So the disk is there. (The last entry) but my linux will for some reason not see it as a usb hard disk. When I insert other usb disks they work fine. It is only this specific disk which causes problems. I have tried on 3 different computers with the same result. A hint to the problem may be that if I add the disk to a windows system(With usb) the disk is called "A fixed disk" and not a portable disk as expected. The disk works fine with linux If i connect it with the sata cabel, but I would really like to have it working with usb too. (To mount it on computers without sata).

    Read the article

< Previous Page | 406 407 408 409 410 411 412 413 414 415 416 417  | Next Page >