Search Results

Search found 12992 results on 520 pages for 'password recovery'.

Page 410/520 | < Previous Page | 406 407 408 409 410 411 412 413 414 415 416 417  | Next Page >

• Partition table corrupted (USB flash drive)

  - by 13ren

  It's an 8 GB Patriot thumb drive, which I've used extensively with lots of data. Today, it is detected, but all data is gone: (EDIT at least some data is still there, but the partition table is gone) EDIT @Sathya (thanks) here's the relevant output from sudo fdisk -l: Disk /dev/sdc: 8019 MB, 8019509248 bytes 247 heads, 62 sectors/track, 1022 cylinders Units = cylinders of 15314 * 512 = 7840768 bytes Disk /dev/sdc doesn't contain a valid partition table It looks like it is /dev/sdc, with that 8 GB... and no partition table. I tried to mount /dev/sdc (and then dmesg | tail): /media> sudo mount /dev/sdc mytmp mount: wrong fs type, bad option, bad superblock on /dev/sdc, missing codepage or other error In some cases useful info is found in syslog - try dmesg | tail or so /media> dmesg | tail [ 24.300000] sdc: unknown partition table [ 24.320000] sd 2:0:0:0: Attached scsi removable disk sdc [ 24.370000] usb-storage: device scan complete [ 26.870000] EXT2-fs error (device sdc): ext2_check_descriptors: Block bitmap for group 1 not in group (block 0)! [ 26.870000] EXT2-fs: group descriptors corrupted! [ 50.420000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 50.430000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 50.430000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 5565.470000] EXT2-fs error (device sdc): ext2_check_descriptors: Block bitmap for group 1 not in group (block 0)! [ 5565.470000] EXT2-fs: group descriptors corrupted! EDIT @Col: results from testdisk Disk /dev/sdc - 8013 MB / 7642 MiB - CHS 1022 247 62 Current partition structure: Partition Start End Size in sectors Partition sector doesn't have the endmark 0xAA55 After I hit [proceed], it says: Structure: Ok. Keys A: add partition, L: load backup, Enter: to continue The "Structure: Ok." seems reassuring... will "A: add partition" make my old data accessible (if it's still there), or will it make a new, fresh partition? Another option is "[ MBR Code ] Write TestDisk MBR code to first sector" - would it be better to do this? EDIT I found that at least some of my data is still on the flash drive, by using the below, and searching for English text in less (like " the "): cat /dev/sde | tr -cd '\11\12\40\1540-\176' | less (The drive changed from "/dev/sdb" to "/dev/sde" because I connected some extra drives today). I've learnt that "/dev/sde1" would be the first partition; and "/dev/sde" is the whole drive. Because unix treats these devices just like files, you can use all the ordinary unix file commands on them, like cat, and then process them like any other stream of data. The tr above removes non-printable characters ("\40" is space, which I wanted to preserve). In less, you can use "/" to search, similar to Vim. How can I get my data back (assuming it's still there)? If only the partition table is corrupted, is there a standard "partition recovery tool"? Is there a way to "repartition" without deleting everything?

  Read the article

• Cannot insert non latin symbols in MySQL

  - by glebreutov

  I'm writing web-app using MySQL version 5.1.45, Tomcat 5.5.28 and Hibernate 3 When I'm trying to save string that contains non-latin characters (for example ??????) error occurs: 1589 [main] WARN org.hibernate.util.JDBCExceptionReporter - SQL Error: 1366, SQLState: HY000 1589 [main] ERROR org.hibernate.util.JDBCExceptionReporter - Incorrect string value: '\xD0\xA3\xD0\xBF\xD1\x8F...' for column 'name' at row 1 Hibernate connection settings <property name="connection.driver_class">com.mysql.jdbc.Driver</property> <property name="connection.url">jdbc:mysql://localhost/E2012?characterEncoding=UTF8&amp;useUnicode=true</property> <property name="connection.username">***</property> <property name="connection.password">***</property> <property name="hibernate.connection.charSet">UTF8</property> MySQL config My.cnf [client] default-character-set=utf8 [mysqld] default-character-set=utf8 Even query set name utf-8 doesn't resolve problem Thanks for help!

  Read the article

• SVN Mac oSX issue - permissions?

  - by Steve Griff

  Hello there, /Volumes/sites is a connection to a samba share that hosts some of our sites. We authorise using a username & password that is the same user/pass to log onto the mac. When committing, (or even doing a cleanup) from the Mac Client side using the svn command line tool or SCPlugin, this error occurs: Commit succeeded, but other errors follow: Error bumping revisions post-commit (details follow): In directory '/Volumes/sites/foobar/public_html' Error processing command 'committed' in '/Volumes/sites/foobar/public_html' Error replacing text-base of 'index.php' Can't move '/Volumes/sites/foobar/public_html/.svn/tmp/text-base/index.php.svn-base' to '/Volumes/sites/foobar/public_html/.svn/text-base/index.php.svn-base': Operation not permitted Any ideas? I think it's to do with permissions on the mac side not being able to move files around on the samba share. Apologies if my question is kinda vague so any extra information I can give please shout. Regards Steve

  Read the article

• Bash commands not executed when through cron job - PHP

  - by basicxman

  Hi there! I have a cron job running a PHP script every five minutes; the PHP script executes two bash commands at the end of the script. I know the script is running due to a log file it appends to. When I run the PHP script manually via the Ubuntu Gnome Terminal both bash commands execute flawlessly; however when the PHP script is triggered via cron, the two bash commands are not ran. Any ideas? $command = 'notify-send "' . count($infoleakPosts) . ' New Posts."'; `$command`; $command = 'firefox http://example.com'; `$command`; */1 * * * * php /home/andrew/grab.php USERNAME PASSWORD # JOB_ID_1

  Read the article

• Setting up Sendgrid using AWS

  - by user2793297

  I currently have a site where the data is hosted on Firebase and the static files are hosted on AWS (I registered my domain using NameCheap, but am routing to AWS using Route 53 and S3). I now want to use SendGrid to send emails, but they are saying that I need to set up an SMTP server. I can't find anywhere what the best way to do this is. Can I get suggestions please on the best solution? I want to use SendGrid to send transactional email such as "Welcome to the site!", "Forgot Password", etc.

  Read the article

• I (think) I want to use a BItWise Operator to check useraccountcontrol property!

  - by Jim

  Hello, Here's some code: DirectorySearcher searcher = new DirectorySearcher(); searcher.Filter = "(&(objectClass=user)(sAMAccountName=" + lstUsers.SelectedItem.Text + "))"; SearchResult result = searcher.FindOne(); Within result.Properties["useraccountcontrol"] will be an item which will give me a value depending on the state of the account. For instance, a value of 66050 means I'm dealing with: A normal account; where the password does not expire;which has been disabled. Explanation here. What's the most concise way of finding out if my value "contains" the AccountDisable flag (which is 2) Thanks in advance!

  Read the article

• AnkhSVN, mysisgit and Pageant

  - by Chalkey

  I have recently installed msysgit on my machine (its running Windows 7) to use Git for some projects. A lot of my projects are under SVN, in which I use AnkhSVN in Visual Studio 2008 to commit etc. Since I have installed msysgit everytime I try to commit, update etc inside Visual Studio, the program C:\msysgit\bin\ssh.exe loads up, asks for my password, then Ankh throws an exception. I currently use Pageant to save my login credentials for SVN - I have TortoiseSVN installed, which is still working fine... Has anybody got any suggestions to get Anhk working again - without uninstalling msysgit? Thanks

  Read the article

• Backing Up Database from Remote Server to Local in VB.NET

  - by Pradeep

  Hi, I am making a VB.NET application that can download/backup the database that is currently on a remote server. I have Remote Server IP,Username,Password and Database name. I am also able to connect to it. But i don't know what to do after connecting to it. I don't know what all files are need to be backed up. ( i think database and log file both must be backed up, i am not sure ) please let me know that basic commmands that i will need to backup the whole database. Thanks in advance.

  Read the article

• A code using SharePoint classes doesn't run on systems not having SharePoint installed

  - by Manish

  I have a window application which uses SP classes to create a site. I works fine on a system having Windows Server 2003 R2 with sharepoint installed. But it doesn't work on a system having XP installed and SharePoint not installed. The fact is that both of these systems are on a intranet. So I assumed that the NON-SP system would be able to run the code and create a site on the system having SP installed if all the required parameters (like serverLocation, domain, username, password) are provided. I did copied the DLLs to these NON-SP system and referenced them to build the project: Microsoft.SharePoint.dll microsoft.sharepoint.portal.dll Microsoft.SharePoint.Publishing.dll But this too didn't worked. What am I missing? Is my assumption wrong?

  Read the article

• Is man-in-the-middle attack a security threat during SSH authentication using keys?

  - by JP19

  Hi, I am no expert in network security, so pardon if this question is not very smart :). I am automating logins to some machines using ssh. I am currently avoiding host-key warnings using StrictHostKeyChecking no. I naively understand that someone can impersonate as the server and I risk losing my password to him if that were the case. However, if I am using only public/private Key based authentication ( using PasswordAuthentication no ), can the intruder still cause harm? So basically, with ssh -o "StrictHostKeyChecking no" -o "PasswordAuthentication no" : 1) Can the intruder decipher my private key? 2) Are there any other security threats? regards, JP

  Read the article

• jQuery Sortable + Droppable z-index problem

  - by unknowndomain

  I am having a probelm with the z-index of my sortable object not being above my droppable. If you visit http://clareshilland.unknowndomain.co.uk/. Press Ctrl + L to bring up the login screen. Enter the username clare and the password shilland. It will then load in the admin bar and if you click manage gallery. A pop down thumbnail view will appear with all the photos from that gallery. The issue is that when you drag the 'polaroids' from the grid to the delete area they are under the delete area. I tried putting the delete area inside the same div as the grid but it makes no difference, I just don't know what to do at this point so any help would be a massive help!

  Read the article

• sending control+c (SIGINT) to NSPIPE in objective-c

  - by Ron

  Hello, I am trying to terminate an openvpn task, spawned via NSTask. My question: Should I send ctrl+c (SIGINT) to the input NSPipe for my NSTask? inputPipe = [NSPipe pipe]; taskInput = [inputPipe fileHandleForWriting]; NSString dataString = @"\cC"; [taskInput writeData:[dataString dataUsingEncoding: [NSString defaultCStringEncoding]]]; Alternatively, I was thinking about using kill( pid, SIGINT ); but it would be much more complicated since the process ID has to be determined via a detour ([task processIdentifier] does not help here) - the original NSTask calls: /bin/bash -c sudo -S | mypassword .... That's not nice, I know but it is only called once and the sudo password has been entered in that case already. thanks for any suggestions/opinions/etc. Ron

  Read the article

• cannot access a site from Mac OSX Lion but can from other machines on network?

  - by house9

  SOLVED: The issue is with the hamachi client, hamachi is hi-jacking all of the 5.0.0.0/8 address block http://en.wikipedia.org/wiki/Hamachi_(software)#Criticism http://b.logme.in/2012/11/07/changes-to-hamachi-on-november-19th/ The fix on Mac LogMeIn Hamachi Preferences Settings Advanced Peer Connections IP protocol mode IPv6 only (default is both) If you can only connect to some of your network over IPv4 this 'fix' will NOT work for you ----- A few weeks ago I started using a service - https://semaphoreapp.com I think they made DNS changes a week ago and ever since I cannot access the site from my Mac OSX Lion (10.7.4) machine (my main development machine) but I can access the site from other machines on my network ipad windows machine MacMini (10.6.8) After some google searching I tried both of these dscacheutil -flushcache sudo killall -HUP mDNSResponder but no go, I've contacted semaphoreapp as well, but nothing so far - also of interest, one of my colleagues has the exact same problem, cannot access via Mac OSX Lion but can via windows machine, we work remotely and are not on the same ISP some additional info Lion (10.7.4) cannot access site host semaphoreapp.com semaphoreapp.com has address 5.9.53.16 ping semaphoreapp.com PING semaphoreapp.com (5.9.53.16): 56 data bytes Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 Request timeout for icmp_seq 3 ping: sendto: No route to host Request timeout for icmp_seq 4 ping: sendto: Host is down Request timeout for icmp_seq 5 ping: sendto: Host is down Request timeout for icmp_seq 6 ping: sendto: Host is down Request timeout for icmp_seq 7 .... traceroute semaphoreapp.com traceroute to semaphoreapp.com (5.9.53.16), 64 hops max, 52 byte packets 1 * * * 2 * * * traceroute: sendto: No route to host 3 traceroute: wrote semaphoreapp.com 52 chars, ret=-1 *traceroute: sendto: Host is down traceroute: wrote semaphoreapp.com 52 chars, ret=-1 .... and MacMini (10.6.8) can access it host semaphoreapp.com semaphoreapp.com has address 5.9.53.16 ping semaphoreapp.com PING semaphoreapp.com (5.9.53.16): 56 data bytes 64 bytes from 5.9.53.16: icmp_seq=0 ttl=44 time=191.458 ms 64 bytes from 5.9.53.16: icmp_seq=1 ttl=44 time=202.923 ms 64 bytes from 5.9.53.16: icmp_seq=2 ttl=44 time=180.746 ms 64 bytes from 5.9.53.16: icmp_seq=3 ttl=44 time=200.616 ms 64 bytes from 5.9.53.16: icmp_seq=4 ttl=44 time=178.818 ms .... traceroute semaphoreapp.com traceroute to semaphoreapp.com (5.9.53.16), 64 hops max, 52 byte packets 1 192.168.0.1 (192.168.0.1) 1.677 ms 1.446 ms 1.445 ms 2 * LOCAL ISP 11.957 ms * 3 etc... 10.704 ms 14.183 ms 9.341 ms 4 etc... 32.641 ms 12.147 ms 10.850 ms 5 etc.... 44.205 ms 54.563 ms 36.243 ms 6 vlan139.car1.seattle1.level3.net (4.53.145.165) 50.136 ms 45.873 ms 30.396 ms 7 ae-32-52.ebr2.seattle1.level3.net (4.69.147.182) 31.926 ms 40.507 ms 49.993 ms 8 ae-2-2.ebr2.denver1.level3.net (4.69.132.54) 78.129 ms 59.674 ms 49.905 ms 9 ae-3-3.ebr1.chicago2.level3.net (4.69.132.62) 99.019 ms 82.008 ms 76.074 ms 10 ae-1-100.ebr2.chicago2.level3.net (4.69.132.114) 96.185 ms 75.658 ms 75.662 ms 11 ae-6-6.ebr2.washington12.level3.net (4.69.148.145) 104.322 ms 105.563 ms 118.480 ms 12 ae-5-5.ebr2.washington1.level3.net (4.69.143.221) 93.646 ms 99.423 ms 96.067 ms 13 ae-41-41.ebr2.paris1.level3.net (4.69.137.49) 177.744 ms ae-44-44.ebr2.paris1.level3.net (4.69.137.61) 199.363 ms 198.405 ms 14 ae-47-47.ebr1.frankfurt1.level3.net (4.69.143.141) 176.876 ms ae-45-45.ebr1.frankfurt1.level3.net (4.69.143.133) 170.994 ms ae-46-46.ebr1.frankfurt1.level3.net (4.69.143.137) 177.308 ms 15 ae-61-61.csw1.frankfurt1.level3.net (4.69.140.2) 176.769 ms ae-91-91.csw4.frankfurt1.level3.net (4.69.140.14) 178.676 ms 173.644 ms 16 ae-2-70.edge7.frankfurt1.level3.net (4.69.154.75) 180.407 ms ae-3-80.edge7.frankfurt1.level3.net (4.69.154.139) 174.861 ms 176.578 ms 17 as33891-net.edge7.frankfurt1.level3.net (195.16.162.94) 175.448 ms 185.658 ms 177.081 ms 18 hos-bb1.juniper4.rz16.hetzner.de (213.239.240.202) 188.700 ms 190.332 ms 188.196 ms 19 hos-tr4.ex3k14.rz16.hetzner.de (213.239.233.98) 199.632 ms hos-tr3.ex3k14.rz16.hetzner.de (213.239.233.66) 185.938 ms hos-tr2.ex3k14.rz16.hetzner.de (213.239.230.34) 182.378 ms 20 * * * 21 * * * 22 * * * any ideas? EDIT: adding tcpdump MacMini (which can connect) while running - ping semaphoreapp.com sudo tcpdump -v -i en0 dst semaphoreapp.com Password: tcpdump: listening on en0, link-type EN10MB (Ethernet), capture size 65535 bytes 17:33:03.337165 IP (tos 0x0, ttl 64, id 20153, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->3129)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 0, length 64 17:33:04.337279 IP (tos 0x0, ttl 64, id 26049, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->1a21)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 1, length 64 17:33:05.337425 IP (tos 0x0, ttl 64, id 47854, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->c4f3)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 2, length 64 17:33:06.337548 IP (tos 0x0, ttl 64, id 24772, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->1f1e)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 3, length 64 17:33:07.337670 IP (tos 0x0, ttl 64, id 8171, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->5ff7)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 4, length 64 17:33:08.337816 IP (tos 0x0, ttl 64, id 35810, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->f3ff)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 5, length 64 17:33:09.337948 IP (tos 0x0, ttl 64, id 31120, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->652)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 6, length 64 ^C 7 packets captured 1047 packets received by filter 0 packets dropped by kernel OSX Lion (cannot connect) while running - ping semaphoreapp.com # wireless ~ $ sudo tcpdump -v -i en1 dst semaphoreapp.com Password: tcpdump: listening on en1, link-type EN10MB (Ethernet), capture size 65535 bytes ^C 0 packets captured 262 packets received by filter 0 packets dropped by kernel and # wired ~ $ sudo tcpdump -v -i en0 dst semaphoreapp.com tcpdump: listening on en0, link-type EN10MB (Ethernet), capture size 65535 bytes ^C 0 packets captured 219 packets received by filter 0 packets dropped by kernel above output after Request timeout for icmp_seq 25 or 30 times from ping. I don't know much about tcpdump, but to me it doesn't seem like the ping requests are leaving my machine?

  Read the article

• Test wordpress sites for SQL Injection on siteurl

  - by Scott B

  I have a client who's wordpress sites have gotten hacked twice by iframe scammers. Each time they've injected iframe code into the content of the sites. This last time, today, they simply changed the siteurl in wp_options to their iframe code. The result was obvious and appeared to simply botch the paths of the scripts that rely on I can't determine if its a password compromise (on FTP or WordPress itself) or a SQL injection to alter siteurl. Since the only thing that was altered is siteurl, I'm thinking perhaps SQL Injection. What are your thoughts? Any way to scan a site for potential SQL injection vulnerabilities? The only active plugins on the site are contact form 7 and google xml sitemaps.

  Read the article

• How do I properly implement Unicode passwords?

  - by Sorin Sbarnea

  Adding support for Unicode passwords it an important feature that should not be ignored by the developpers. Still adding support for Unicode in the passwords it's a tricky job because the same text can be encoded in different ways in Unicode and this is not something you may want to prevent people from logging in due to this. Let's say that you'll store the passwords os UTF-8. Now the question is how you should normalize the Unicode data? You had to be sure that you'll be able to compare it. You need to be sure that when the next Unicode standard will be released it will not invalidate your password verification. Note: still there are some places where Unicode passwords are probably never be used, but this question is not about why or when to use Unicode passwords, is about how to implement them the proper way.

  Read the article

• Run EJB3Unit against Oracle Database

  - by justastefan

  I want to run EJB3Unit-Test in my oracle 10g Database. Therefore I use this configuration (ejb3unit.properties). ### The ejb3unit configuration file ### ejb3unit.inMemoryTest=false ejb3unit.connection.url=jdbc:oracle:thin:....:1432:SID ejb3unit.connection.driver_class=oracle.jdbc.OracleDriver ejb3unit.connection.username=user ejb3unit.connection.password=name ejb3unit.dialect=org.hibernate.dialect.Oracle10gDialect ejb3unit.show_sql=true ## values are create-drop, create, update ## ejb3unit.schema.update=create I will result in the following error: Caused by: HibernateException: cannot instantiate dialect class ... org.hibernate.dialect.Oracle10gDialect cannot be cast to org.ejb3unit.hibernate.dialect.Dialect How can ejb3unit-testing be done using oracle db?

  Read the article

• Hell: NTFS "Restore previous versions"...

  - by ttsiodras

  The hell I have experienced these last 24h: Windows 7 installation hosed after bluetooth driver install. Attempting to recover using restore points via "Repair" on the bootable Win7 installation CD. Attempting to go back one day in the restore points. No joy. Attempting to go back two days in the restore points. No joy. Attempting to go back one week in the restore points. Stil no joy. Windows won't boot. Apparently something is REALLY hosed. And then it hits me - PANIC - the restore points somehow reverted DATA files to their older versions! Word, Powerpoint, SPSS, etc document versions are all one week old now. Using the "freshest" restore point. Failed to restore yesterday's restore point!!! I am stuck at old versions of the data!!! Booting KNOPPIX, mounting NTFS partition as read-only under KNOPPIX. Checking. Nope, the data files are still the one week old versions. Booting Win7 CD, Recovery console - Cmd prompt - navigating - yep, data files are still one week old. Removing the drive, mounting it under other Win7 installation. Still old data. Running NTFS undelete on the drive (read-only scan), searching for file created yesterday. Not found. Despair. At this point, idea: I will install a brand new Windows installation, keeping the old one in Windows.old (default behaviour of Windows installs). I boot the new install, I go to my C:\Data\ folder, I choose "Restore previous versions", click on yesterday's date, and click open... YES! It works! I can see the latest versions of my files (e.g. from yesterday). Thank God. And then, I try to view the files under the "yesterday snapshot-version" of c:\Users\MyAccount\Desktop ... And I get "Permission Denied" as soon as I try to open "Users\MyAccount". I make sure I am an administrator. No joy. Apparently, the new Windows installation does not have access to read the "NTFS snapshots" or "Volume Shadow Snapshots" of my old Windows account! Cross-installation permissions? I need to somehow tell the new Windows install that I am the same "old" user... So that I will be able to access the "Users\MyAccount" folder of the snapshot of my old user account. Help?

  Read the article

• What is an SSH key?

  - by acidzombie24

  I signed up for github and notice the ssh key option which looked interesting. I originally expected something like an ssl key (name, co name, etc). After going through it i notice i only put a password and it is always myuser@comp-name (this is windows). Why? I thought it was a user/pass id and i can create separate keys for separate purpose for privacy reasons. Now i see i am required to use one to create a repository. Also i see something about a 'private key file' when looking at options. What exactly is an SSH Key and how can i create a separate user without creating a separate login in windows.

  Read the article

• SOA design principles with regards to database relationships

  - by Eitan

  If I were to extricate my current membership provider from my solution, i.e. as a dll and expose it as a web service with it's own db, how would I model the relationships with regards to SOA design. For example I have a table: USER id, name, lastname, username, password, role. and table PRODUCT id, name, price, createdate, userid the foreign key being userid to table user. How would I model the relationship and/or query the db. If I wanted to get all products that were uploaded today for example, before I would query: SELECT u.name, u.lastname, u.username, p.* FROM PRODUCT p INNER JOIN USER u ON p.userid = u.id WHERE createdate = '05/05/2010' Now that I don't have the table within the database how would I perform this query? Thanks.

  Read the article

• ASP.NET application partially reading external configuration

  - by Trent

  I have an ASP.NET web app and am attempting to reference an external config (using enterprise application blocks configuration) for some of the configuration but it is not entirely working. I previously had all of the configuration info in the web.config (and it was working), but we are wanting to share some of this configuration information between multiple apps. When I put configurationSource tag in the web.config, and read the configuration through the WebConfigurationManager object, it loads some of the external config info (Logging) but not the connectionStrings and not the custom section I created. So its reading it (logging is working), but some dots aren't being connected and my connection strings aren't coming through. Again, it worked when it was all in the web.config. Any idea what needs to change to be able to reference an external configuration source and have it all come through? [Code that accesses web.config] Configuration webConfig = System.Web.Configuration.WebConfigurationManager.OpenWebConfiguration("~"); ConnectionStringSettingsCollection connectionStrings = System.Web.Configuration.WebConfigurationManager.ConnectionStrings; [web.config] <configuration> <configSections> <section name="enterpriseLibrary.ConfigurationSource" type="Microsoft.Practices.EnterpriseLibrary.Common.Configuration.ConfigurationSourceSection, Microsoft.Practices.EnterpriseLibrary.Common, Version=4.1.0.0, Culture=neutral, PublicKeyToken=74025d8738dfe4ce" /> <sectionGroup name="system.web.extensions" type="System.Web.Configuration.SystemWebExtensionsSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <sectionGroup name="scripting" type="System.Web.Configuration.ScriptingSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <section name="scriptResourceHandler" type="System.Web.Configuration.ScriptingScriptResourceHandlerSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> <sectionGroup name="webServices" type="System.Web.Configuration.ScriptingWebServicesSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <section name="jsonSerialization" type="System.Web.Configuration.ScriptingJsonSerializationSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="Everywhere" /> <section name="profileService" type="System.Web.Configuration.ScriptingProfileServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> <section name="authenticationService" type="System.Web.Configuration.ScriptingAuthenticationServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> <section name="roleService" type="System.Web.Configuration.ScriptingRoleServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> </sectionGroup> </sectionGroup> </sectionGroup> </configSections> <enterpriseLibrary.ConfigurationSource selectedSource="File Configuration Source"> <sources> <add name="File Configuration Source" type="Microsoft.Practices.EnterpriseLibrary.Common.Configuration.FileConfigurationSource, Microsoft.Practices.EnterpriseLibrary.Common, Version=4.1.0.0, Culture=neutral, PublicKeyToken=74025d8738dfe4ce" filePath="C:\MSEAB\MSEAB.config" /> </sources> </enterpriseLibrary.ConfigurationSource> ... ... </configuration> [external MSEAB.config] <configuration> <configSections> <section name="loggingConfiguration" type="Microsoft.Practices.EnterpriseLibrary.Logging.Configuration.LoggingSettings, Microsoft.Practices.EnterpriseLibrary.Logging, Version=4.1.0.0, Culture=neutral, PublicKeyToken=74025d8738dfe4ce" /> <section name="dataConfiguration" type="Microsoft.Practices.EnterpriseLibrary.Data.Configuration.DatabaseSettings, Microsoft.Practices.EnterpriseLibrary.Data, Version=4.1.0.0, Culture=neutral, PublicKeyToken=74025d8738dfe4ce" /> <sectionGroup name="customSectionGroup"> <section name="customSection" type="app.customSection" allowLocation="true" allowDefinition="Everywhere" /> </sectionGroup> </configSections> <loggingConfiguration name="Logging Application Block" tracingEnabled="true" defaultCategory="General" logWarningsWhenNoCategoriesMatch="true"> ... </loggingConfiguration> <connectionStrings> <clear /> <add name="DB.DEV" connectionString="User ID=user;Password=pwd;Data Source=DV408;" providerName="Oracle.DataAccess.Client"/> <add name="DB.TEST" connectionString="User ID=user;Password=pwd;Data Source=TS408;" providerName="Oracle.DataAccess.Client"/> ... </connectionStrings> <customSectionGroup> <customSection notificationemail="[email protected]" dirPath="C:\Dir" initialrowlimit="500" maxrowlimit="1500" adminadgroup="_admins"> </customSection> </customSectionGroup> </configuration>

  Read the article

• Eidetic memory: What magic numbers you still remember?

  - by Hao

  Long before you practice writing readable code, what "magic numbers" you still remember up to this day? here's some of my list: 72 80 75 77 13 32 27 - up down left right enter space escape 1 2 4 128 - blue green red blink 67h 33h 17h - interrupt for EMS, mouse, printer function AH 9, interrupt 21 alt+219 for block ASCII alt+164 ñ 90 NOP 13 10 carriage return, line feed ascii 1 and 2 face, ascii 3 heart. no not this heart: <3 :-) debug -o72,10 -o71,12 clears the BIOS password. I don't know what those numbers mean, it's like a trade secret that gets shared with each other during college days. ascii 7 sounds a beep P.S. Somehow, remembering some of these magic numbers can help you in some tech problems, your keyboard is broken, the office pal's keyboard doesn't have accented characters. An anecdote, during college, one of my friend asked me how to remove the newlines in his Word document. Not having used Word so much then, I somehow "intuitively" guessed to find ^013 and replace it with blank. Well it works :-)

  Read the article

• Echo autoincrement id doubt

  - by Marcelo

  Hi, can I print the id, even if it's autoincrement ? Because the way I'm doing I'm using an empty variable for id. $id= ""; mysql_connect(localhost,$username,$password); @mysql_select_db($database) or die ("Não conectou com a base $database"); mysql_query("INSERT INTO table1(id,...) VALUES ('".$id."',....)") or die(mysql_error()); mysql_close(); echo "Your id is :"; echo "".$id; I'm trying to print the id, but it's coming blank. I checked the table and there's an id number there. How can I print it then at? Thanks for the attention

  Read the article

• How can I create a new email account in Java?

  - by Jeremy Goodell

  I am able to send and receive emails from my JSPs and associated Java code using the Java Mail API (javax.mail.*). Now I would like to create a new POP3 email account programmatically when a user registers for my site. I've found surprisingly little information about this with web searches. I would think it would be a somewhat common problem. It appears that the Java Mail API does not provide any assistance in this area. I have many email accounts available under my godaddy account, and to manually create an account, I just go to the godaddy email control panel, click Add, and specify the email address and password. This is exactly what I would like to do via a Java program. Any ideas?

  Read the article

• How to move Mailboxes over from old Exchange 2007 to new EBS 2008 network?

  - by Qwerty

  Hi all, This q is similar to: http://serverfault.com/questions/39070/how-to-move-exchange-2003-mailbox-or-store-from-2003-to-2007-on-separate-networks Basically I am trying to move our exchange mailboxes over to a test domain that is hosting EBS2008 with Exchange 2007. We plan to move as soon as we can when we have our exchange data over. I have tried moving a db with mailboxes over but cannot get it to mount in the new Exchange in any way possible, including mounting it onto a recovery store. From my understanding the ONLY prerequisite for moving Exchange DBs across is that it must have the same Organizational name (unlike previous versions of Exchange). If anyone has any insight as to why I cannot mount and simply reattach the mailboxes, please give me an idea as to what could be wrong. It should be as simple as this. Note that the DBs I have are in a clean state. I cannot use ExMerge because I am not running any mailboxes on 2003. I have also tried using a 32bit Vista machine with the Export-Mailbox cmdlet to extract mailboxes but anything I do to it results in Permission errors. I have tried to troubleshoot these with no success. I am running in full admin with proper exchange roles and yet it still gives me access denied errors: Export-Mailbox : MapiExceptionNetworkError: Unable to make admin interface conn ection to server. (hr=0x80040115, ec=-2147221227) Also some errors show in the management console: get-MailboxDatabase Completed Warning: ERROR: Could not connect to the Microsoft Exchange Information Store service on server TATOOINE.baytech.local. One of the following problems may be occurring: 1- The Microsoft Exchange Information Store service is not running. 2- There is no network connectivity to server TATOOINE.baytech.local. 3- You do not have sufficient permissions to perform this command. The following permissions are required to perform this command: Exchange View-Only Administrator and local administrators group for the target server. 4- Credentials have been cached for an unpriviledged user. Try removing the entry for this server from Stored User Names and Passwords. Why I have to use a 32bit machine to export a simple .pst file is beyond me... So yeah I am now out of ideas and any help would be great! Thanks in advance.

  Read the article

• Update payment details using Authorize.net

  - by Aditya

  Hello everybody, When i update the existing subscription info using update_recurring method of autorize.net gateway then payment details(means 'credit card number', 'CVV number' and 'expiry date' ) are not being updated. My code snippet is as follows:- def create_card_subscription credit_card = ActiveMerchant::Billing::CreditCard.new( :first_name = params[:payment_details][:name], :last_name = params[:payment_details][:last_name], :number = params[:payment_details][:credit_card_number], :month = params[:expiry_date_month], :year = params[:expiry_date_year], :verification_value = params[:payment_details][:cvv_code] ) if credit_card.valid? gateway = ActiveMerchant::Billing::AuthorizeNetGateway.new(:login = '***', :password = '******') response = gateway.update_recurring( { "subscription.payment.credit_card.card_number" = "4111111111111111", :duration ={:start_date='2010-04-21', :occurrences=1}, :billing_address={:first_name='xyz', :last_name='xyz'}, :subscription_id="**" } ) if response.success? puts response.params.inspect puts "Successfully charged $#{sprintf("%.2f", amount / 100)} to the credit card #{credit_card.display_number}. The Account number is #{response.params['rbAccountId']}" else puts response.message end else #Credit Card information is invalid end render :action="card_payment" end How can it be possible? Thanks in advance, Gaurav Kumar

  Read the article

< Previous Page | 406 407 408 409 410 411 412 413 414 415 416 417  | Next Page >