Search Results

Search found 12055 results on 483 pages for 'password complexity'.

Page 414/483 | < Previous Page | 410 411 412 413 414 415 416 417 418 419 420 421  | Next Page >

• ssh works fine when using public interface, but slow when using private interface

  - by Kevin M

  My Linux(UbuntuEEE) to Linux(CentOS) ssh takes a long time to log in(~15 seconds) when using the private interface, but not when using the public one. I have a Linux box acting as my router. As such, it has multiple interfaces(75.xxx.xxx.xxx, 192.168.1.1). I can ssh in from the internal interface(192.168.1.65 to .1), but it will take a while. I can ssh into the public address, and it goes quickly(~1 second). I have another box that I can ssh into the inside interface from and it goes quickly. iptables is set to accept packets coming into the interface immediately. sshd's UseDNS is normally on; I get the same problem if I turn it off and restart sshd. I normally use public-key authentication; I have done a mv ~/.ssh/ ~/ssh/ and it will ask me for a password after going slowly. After logging in(using either interface), speed is quick. ssh client version(via ssh -v):OpenSSH_4.7p1 Debian-8ubuntu1.2, OpenSSL 0.9.8g 19 Oct 2007 ssh server version(via rpm -qv openssh_server):openssh-server-4.3p2-29.el5

  Read the article

• Internet in the router but not in the local network.

  - by TheMouse

  I have a PC and a laptop (Windows 7 - both) which should connect through router to Internet. The router is Linksys wrt120. My ISP is using PPPoE. I have connected the Internet cable to the router, clone the MAC of my PC, writing the username and the password for my Internet connection. After seconds the router has acquired IP from my ISP. I have used the administration panel of Linksys and with the help of the ping and tracert commands which are built into it - I can connect to the world, outside the network. The problem is when I try to connect the PC or the laptop to the network. There's no problem here. The DHCP server of the router gives them appropriate addresses. The problem is that they couldn't connect to either Internet addresses (google.com) or IP addresses. But they can connect to the router and its control panel. I tried several times, reset the router..but there's no Internet..still.

  Read the article

• Implementing emailing (bulk & event based) features for my website.

  - by Kabeer

  Hello. For my upcoming social networking website, I am looking for suggestions on the best way to implement emailing. Here are some of my requirements and constraints: Requirements: - Should be able to send emails based on events (new registrations, change password, etc.), promotions (advertisements based on user consent), bulk mails (newsletters), reminders (profile updates), etc. I hope I got the point through. - Should be able to process faults (incorrect email address, mail-box full, etc) - User initiated invites (inviting friends to connect) Constraints: - As of now I am looking at Godaddy for hosting. Subsequently I shall move to, may be Amazon Cloud. Godaddy seems to be excruciatingly conservative (not bad always) when it comes to the ability to send email. - My tests on Godaddy so far have been discouraging. There is limit to no. of emails I can send and sometimes if emails carries special characters it throws strange exceptions like there was a virus affected attachment (even though I hadn't attached a thing). The replies from Godaddy support have been equally funny. My intent is not to portray Godaddy as wrong but I am looking for a work-around that frees me from said constraints. I am looking for a mechanism / service that is either free of very cost effective. I wonder how other sites address this. Mine is a .Net / Windows based application.

  Read the article

• Office documents on intranet all requiring second login and can't pass auth? Disable webdav?

  - by DOTang

  I am not sure what is going on, but recently all the Office documents on our intranet get prompted a second time for login and according to the error logs it looks like it's trying to use webdav to open (an editable?) version of the document to save directly on the server? We have no sharepoint server setup or anything, but this shouldn't be happening. All I want is for the document to be saved or opened from a local copy in temp like normal. Here is the log: Line 57499: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 Line 57500: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 Line 57501: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 The log basically contains a bunch of these. How can I disable this behavior so that office documents that are downloaded aren't attempted to be used through webdav?? Edit: I should clarify behavior, it asks if you want to save or open it, upon choosing open open, it asks to re-authenicate, you put in the user information and the login box comes up 3 times acting like you entered the wrong password. For some users, after passing the login box the third time, it still opens up, for others their browser just locks up. It also doesn't even look like webdav is installed on our server, I see no config options in IIS for it as outlined on this page: http://learn.iis.net/page.aspx/350/installing-and-configuring-webdav-on-iis-7/#001

  Read the article

• ssh many users to one home

  - by filippo

  Hiya, I want to allow some trusted users to scp files into my server (to an specific user), but I do not want to give these users a home, neither ssh login. I'm having problems to understand the correct settings of users/groups I have to create to allow this to happen. I will put an example; Having: MyUser@MyServer MyUser belongs to the group MyGroup MyUser's home will be lets say, /home/MyUser SFTPGuy1@OtherBox1 SFTPGuy2@OtherBox2 They give me their id_dsa.pub's and I add it to my authorized_keys I reckon then, I'd do in my server something like useradd -d /home/MyUser -s /bin/false SFTPGuy1 (and the same for the other..) And for the last, useradd -G MyGroup SFTPGuy1 (then again, for the other guy) I'd expect then, the SFTPGuys to be able to sftp -o IdentityFile=id_dsa MyServer and to be taken to MyUser's home... Well, this is not the case... SFTP just keeps asking me for a password. Could someone point out what am I missing? Thanks a mil, f. [EDIT: Messa in StackOverflow asked me if authorized_keys file was readable to the other users (members of MyGroup). Its an interesting point, this was my answer: Well, it wasn't (it was 700), but then I changed the permissions of the .ssh dir and the auth file to 750 though still no effect. Guess it's worth mentioning that my home dir ( /home/MyUser) is also readable for the group; most dirs being 750 and the specific folder where they'd drop files is 770. Nevertheless, about the auth file, I reckon the authentication would be performed by the local user on MyServer, isn't it? if so, I don't understand the need for other users to read it... well.. just wondering. ]

  Read the article

• Windows 8 preinstall downgrade to Win 7: UEFI problems :/

  - by Tim Flemming

  I have a friend who has a Hp Laptop with UEFI booting. He locked himself out of windows 8 (forgot his password)... so he called me. Well after trying to use the latest version of chntpw in UBCD5.2.6, i came to the conclusion i needed to wipe the drive and install windows 7. A little googling suggested using certain versions of chntpw, but i decided to not waste the time burning endless CDs. Anyway, He agreed to installing Win7 "I hate the big tile thingys". So i attacked with Gparted. Wiped the whole drive. Set flags to boot. Set part table as MBR. However upon trying to install win7, it still claimed i had a GPT style disk. unable to install. the only thing i can think of I'm doing wrong is not changing the bios/UEFI to legacy... My question is, If I enable legacy, somehow get the drive to actually be MBR, and use my X86 DVD, should I be good? Is there some common glitches ppl miss when dealing with GPT/EFI/UEFI? I need answers cuz he now has a blank laptop which I am responsible for. Another question. windows 8 came installed on a GPT disk. SO WHY WHEN I BOOT THE INSTALL DVD DOES IT SAY IT CANT INSTALL TO A GPT STYLE DISK??? WTF??? talk about the bleeding edge man.

  Read the article

• Linux: Can't overwrite files on samba store

  - by jonescb

  I'm using CentOS 5.5 with smbclient 3.0.33-3.28-el5 (latest version in repo), and I can't overwrite files in my Samba store. I am not the admin for the Samba server, so there isn't anything I can do server side. But I do have write permission to the server. I know the server runs Windows XP or Server 2003; I don't know. I can delete the file, and then copy the new version over, but I can't overwrite it. Using the cp command I'll get this error: [jonescb@localhost ~]$ cp foo.txt /mnt/si_storage/foo.txt cp: cannot create regular file `/mnt/si_storage/foo.txt': No such file or directory` And if I edit a file on the server using vim, I can save it once, but if I save it again I get this: "/mnt/si_storage/foo.txt" E212: Can't open file for writing This is my /etc/fstab entry for the samba server: //192.168.1.2/SI_STORAGE /mnt/si_storage cifs username=myuser,password=mypass 0 0 Edit: I can overwrite files just fine on my XP machine. The CentOS box is the only one having problems.

  Read the article

• How do I cancel windows server 2003 repair install?

  - by Kilgore2k

  System: Windows 2003 Server Enterprise Scenario: NTDS db is corrupt and all attempts to fix with esentutl fail. Ran chkdsk which seemed to repair disk error and give access to the ntds.dit file but still esentutl fails. (Attached the drive to a different server to run the esentutl) Error: Access to source database '[path to copy of]/ntds.dit' failed with Jet error -1022. Operation terminated with error -1022 (JET_errDiskIO, Disk IO error) after 0.170 seconds. This error occurs on any disk I cpoy the files to including original location in C:\WINDOWS\NTDS\ Now enter the "Stupid!" and "what was I thinking!?" part (must be the late hour...) Stupid: No updated backup - after using a backup I get a network password error in the lsass error. what was I thinking!?: Started the install repair from the original CD but the install fails since the AD fails to start. Now I cant boot into any mode (safe mode, AD restore etc) nor complete the repair install. I would really like to avoid a fresh install since I have the Exchange server on this DC and would rather migrate to a new server than have to start from scratch. Thanks!

  Read the article

• Is it possible to trace someone using Google during an online exam?

  - by George

  I happen to be a professor at a reputed college. I want to design an online exam for over 1000 students via around 50 computers right after the vacation ends. Now the problem is that I have heard that many students use Google on a different tab to find answers when no invigilator is around. I want to know if there is a way to backtrace it after the exams via some kind of history or any other possible way. In our university there is a standard system. I am not good with computers but I will try to explain. Each computer uses mozilla to connect to a server centrally located via an IP. The students open it and enter a unique ID and password to start the exams. Many questions are jumbled and different groups of students give exam in a different time slot. Is there any way to trace it since I want to set an example for students so they won't cheat and give exams in an honest way. Additional details: Since the number of computers are less than the number of students, more than 10 students are going to use a single computer on a single day over a period of 10 hours. After this, if I check the history (and let's say someone even forgot to delete the history and I see it), will I able to figure out who among the 10 has done it? Moreover, is it even practical and feasible?

  Read the article

• Linux security: The dangers of executing malignant code as a standard user

  - by AndreasT

  Slipping some (non-root) user a piece of malignant code that he or she executes might be considered as one of the highest security breaches possible. (The only higher I can see is actually accessing the root user) What can an attacker effectively do when he/she gets a standard, (let's say a normal Ubuntu user) to execute code? Where would an attacker go from there? What would that piece of code do? Let's say that the user is not stupid enough to be lured into entering the root/sudo password into a form/program she doesn't know. Only software from trusted sources is installed. The way I see it there is not really much one could do, is there? Addition: I partially ask this because I am thinking of granting some people shell (non-root) access to my server. They should be able to have normal access to programs. I want them to be able to compile programs with gcc. So there will definitely be arbitrary code run in user-space...

  Read the article

• VPN - local and remote networks IP collision

  - by Guido García

  I have created a VPN connection in Windows using the New Network Connection wizard that comes with Windows. It works without problems in most places, but there is one concrete place where, despite the connection to the remote public IP works fine, it is not able to validate the login/password and establish the VPN connection. In this place, the network is 10.0.0.x (the same I use in other places where I am able to connect). The remote network is 192.168.x.x, so I suspect there is some kind of IP collision, because before connecting, a traceroute to i.e. 192.168.0.40 does not fail. 1 4 ms 1 ms 1 ms LINKSYS [10.0.0.1] 2 5 ms 1 ms 1 ms 172.26.27.1 3 4 ms 5 ms 3 ms 192.168.1.100 ... (more) I can't modify the local network further than the first router (10.0.0.1). That is the only different I've found so far. Any idea about how to solve it? Thank you.

  Read the article

• SQL Server 2012 Maintenance Plan can't modify

  - by Crazyd

  Click on any created Maintenance Plan: TITLE: Microsoft SQL Server Management Studio Value cannot be null. Parameter name: component (System.Design) BUTTONS:OK Create a new Plan I get this error: TITLE: Maintenance Plan Wizard Progress Saving maintenance plan failed. ADDITIONAL INFORMATION: The SaveToSQLServer method has encountered OLE DB error code 0x80004005 (Unspecified error). The SQL statement that was issued has failed. The SaveToSQLServer method has encountered OLE DB error code 0x80004005 (Unspecified error). The SQL statement that was issued has failed. BUTTONS:OK Edit an already created Backup Plan: Error 1 Error loading 'BackupDb' : The LoadFromSQLServer method has encountered OLE DB error code 0x80004005 (Unspecified error). The SQL statement that was issued has failed. . server=SERVER;package=Maintenance Plans\BackupLeadsDb; 1 1 Attemped Solutions: I've changed password for SA Account; I use Windows Authentication to log in; and I've registered C:\Program Files (x86)\Microsoft SQL Server\110\DTS\Binn\DTS.dll. Repair SQL Server 2012, Uninstall/ReInstall SQL Server 2012.

  Read the article

• IIS6 site using integrated authentication (NTLM) fails when accessed with Win7 / IE8

  - by Ciove

  Hi, I'm having pretty similar problems as described in case 139099, but the fix there doesn't seem to work for me. Here's the details: Server: Win2003Srv R2 SP2 (stadalone, not a member of a domain). IIS6, TCP/443 (https). Anonymous access disabled. Integrated Windows authentication enabled. Local useraccouts Each useraccount has own virtual folder with change access and read access to site root. The 'adsutil NTAuthenticationProviders "NTLM"' -thing set to site root and useraccount's virtual folder. Client: Win7 Enterprise Member of a AD-Domain IE8 Allows three login attepts then fails. Using [webservername][username] in the logon window (Windows security) Logon using other browsers (Chrome and Firefox) works OK. The Web services log shows one 401.2 and two 401.1 events. The Security Event log shows two events, first is Fauilure Audit (680), The second event is Fauilure Audit (529) with these details: Logon Failure: Reason: Unknown user name or bad password User Name: [username] Domain: [webservername] Logon Type: 3 Logon Process: NtLmSsp Authentication Package: NTLM Workstation Name: [MyWorkstation] Caller User Name: - Caller Domain: - Caller Logon ID: - Caller Process ID: - Transited Services: - Source Network Address: [999.999.999.999] Source Port: 20089 Any ideas appreciated.

  Read the article

• What's the best way to telnet from a remote Windows PC without using RDP?

  - by Rob D.

  Three Networks: 10.1.1.0 - Mine 172.1.1.0 - My Branch Office 172.2.2.0 - My Branch Office's VOIP VLAN. My PC is on 10.1.1.0. I need to telnet into a Cisco router on 172.2.2.0. The 10.1.1.0 network has no routes to 172.2.2.0, but a VPN connects 10.1.1.0 to 172.1.1.0. Traffic on 172.1.1.0 can route to 172.2.2.0. All PCs on 172.1.1.0 are running Windows XP. Without disrupting anyone using those PCs, I want to open a telnet session from one of those PCs to the router on 172.2.2.0. I've tried the following: psexec.exe \\branchpc telnet 172.2.2.1 psexec.exe \\branchpc cmd.exe telnet 172.2.2.1 psexec.exe \\branchpc -c plink -telnet 172.2.2.1 Methods 1 and 2 both failed because telnet.exe is not usable over psexec. Method 3 actually succeeded in creating the connection, but I cannot login because the session registers my carriage return twice. My password is always blank because at the "Username:" prompt I'm effectively typing: Routeruser[ENTER][ENTER] It's probably time to deploy WinRM... Does anyone know of any other alternatives? Does anyone know how I can fix plink.exe so it only receives one carriage return when I use it over psexec?

  Read the article

• Why isn't Apache Basic authentication working?

  - by Brad

  I just upgraded Apache from it's 2003 build, to a squeaky-clean, brand-new 2.4.1 build. All seems pretty good except for one glaring thing: In my httpd.conf file I have the following: <Directory /> AllowOverride none Options FollowSymLinks AuthType Basic AuthName "Enter Password" AuthUserFile /var/www/.htpasswd Require valid-user </Directory> This should allow only users in the specified auth file to access the server - just as it had under the older version of Apache. (Right?) However, it's not working. Requests are granted with no authentication provided. When I switch logging to LogLevel Debug, for the accesses, it says: [Sat Mar 24 21:32:00.585139 2012] [authz_core:debug] [pid 10733:tid 32771] mod_authz_core.c(783): [client 192.168.1.181:57677] AH01626: authorization result of Require all granted: granted [Sat Mar 24 21:32:00.585446 2012] [authz_core:debug] [pid 10733:tid 32771] mod_authz_core.c(783): [client 192.168.1.181:57677] AH01626: authorization result of <RequireAny>: granted I really don't know what this means - and I (to the best of my knowledge) don't have any "Require all granted" or "" statements in any of my files. Any ideas why this isn't working, or where to debug??

  Read the article

• How to secure an Internet-facing Elastic Search implementation in a shared hosting environment?

  - by casperOne

  (Originally asked on StackOverflow, and recommended that I move it here) I've been going over the documentation for Elastic Search and I'm a big fan and I'd like to use it to handle the search for my ASP.NET MVC app. That introduces a few interesting twists, however. If the ASP.NET MVC application was on a dedicated machine, it would be simple to spool up an instance of Elastic Search and use the TCP Transport to connect locally. However, I'm not on a dedicated machine for the ASP.NET MVC application, nor does it look like I'll move to one anytime soon. That leaves hosting Elastic Search on another machine (in the *NIX world) and I would probably go with shared hosting there. One of the biggest things lacking from Elastic Search, however, is the fact that it doesn't support HTTPS and basic authentication out of the box. If it did, then this question wouldn't exist; I'd simply host it somewhere and make sure to have an incredibly secure password and HTTPS enabled (possibly with a self-signed certificate). But that's not the case. That given, what is a good way to expose Elastic Search over the Internet in a secure way? Note, I'm looking for something that hopefully, will not require writing code to provide shims for the methods that I want (in other words, writing forwarders).

  Read the article

• tftpd starts randomly

  - by Mutant

  A few days ago my Little Snitch filter starts popping up tftpd. I'd never seen this before, so I immediately start freaking out thinking my Mac has been compromised. I can't find anything unusual on the system. The process usually dies before I can trace it (little snitch never allowed the connection just left the popup up). I finally caught it once, and found this: [10:32]: sudo lsof -nlP | fgrep tftp Password: tftpd 1924 18446744 cwd DIR 1,3 1326 2 / tftpd 1924 18446744 txt REG 1,3 29856 163979456 /usr/libexec/tftpd tftpd 1924 18446744 txt REG 1,3 600576 163686622 /usr/lib/dyld tftpd 1924 18446744 txt REG 1,3 303300608 189014898 /private/var/db/dyld/dyld_shared_cache_x86_64 tftpd 1924 18446744 0u IPv4 0x34a76100fcbb06e3 0t0 UDP *:55818 tftpd 1924 18446744 2u IPv4 0x34a76100f1113c53 0t0 UDP *:69 [10:32]: ps ax | fgrep 1924 1924 ?? S 0:00.00 /usr/libexec/tftpd -i /private/tftpboot 1949 s000 S+ 0:00.00 fgrep 1924 For the life of me I can't figure out what is starting this. Nothing in cron, launchdaemons, etc. Google searches haven't yielded much either. The connection IP is different each time. So my question is: Has anyone seen anything like this before?

  Read the article

• Mounting fuse sshfs fails when invoked by Cron on FreeBSD 9.0

  - by Tal

  I have a remote server filesystem that I'm attempting to mount locally on a FreeBSD 9 machine via FUSE sshfs, and Cron for a backup routine. I have ssh keys between the boxes setup to allow for passwordless login as the root user on the local machine. Cron is set to run the following script (in Root's crontab): #!/bin/sh echo "Mounting Share" /usr/local/bin/sshfs -C -o reconnect -o idmap=user -o workaround=all <remote user>@<remote domain>.com: /mnt/remote_server As root, I can run this script on the command line without issue, and without being asked for a password the share mounts successfully. Yet, when run by Cron the script fails. The path to sshfs is identical to the value of which sshfs Here is the email root receives from the Cron Daemon: X-Cron-Env: <SHELL=/bin/sh> X-Cron-Env: <HOME=/root> X-Cron-Env: <PATH=/usr/bin:/bin> X-Cron-Env: <LOGNAME=root> X-Cron-Env: <USER=root> Mounting Share fuse: failed to exec mount program: No such file or directory fuse: failed to mount file system: No such file or directory I'm stumped as to why I'm receiving No such file or directory in this instance. It further seems odd given that the paths appear to be correct. I've also attempted to compare the output of env on the shell with env inserted into the script. I don't see any environment variables that should cause this trouble. At bootup, FUSE reports its version as: fuse4bsd: version 0.3.9-pre1, FUSE ABI 7.8 Help me ServerFault wizards, you're my only hope!

  Read the article

• EC2 AMI won't boot after edit

  - by Eric Lars0n

  I did something stupid, I got a new laptop and copied everything over to the new one, then wiped the old one clean. Then I realized that I forgot to copy the private key out of .ssh that I use to connect to my AWS EBS backed instance. So I can't log in to my custom AMI. So I created a new Volume from the Snapshot of the AMI, then started up a public instance and attached the Volume to it, edit the sshd_config to allow for password log in. Unmounted the volume, detached it, made a snapshot of it, then made a new AMI from the snapshot. The new AMI launches, but never passes the Status Checks and is not reachable. What am I doing wrong? Or alternatively how can I fix my problem? Edit: Adding some of the console output Linux version 2.6.16-xenU ([email protected]) (gcc version 4.0.1 20050727 (Red Hat 4.0.1-5)) #1 SMP Mon May 28 03:41:49 SAST 2007 BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000006a400000 (usable) 980MB HIGHMEM available. 727MB LOWMEM available. NX (Execute Disable) protection: active IRQ lockup detection disabled RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize NET: Registered protocol family 2 Registering block device major 8 XENBUS: Timeout connecting to devices! Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,0)

  Read the article

• Some of my keys are automatically being pressed along with other keys

  - by Santosh

  History The last time when my computer shutdown was a power failure. Now some keys are automatically being pressed when I type something. The last thing I did to keyboard setting was adding a keyboard layout (on Ubuntu). What is happening Whenever I press c, xc is writeen s gives me sd d gives me sd e gives me we 2 gives me 23, So when I want @ it gives me @# 3 gives me 23 Pressing CAPS Lock gives me F3 and vice-versa. All other key are either working fine or I don't use them. I have two operating system Ubuntu and Windows, I use Windows very less and found this problem on Ubuntu, but as soon as I logged in to Windows (for checking) then I found that Windows has the same problem. Effects on my life This starts form the time of login, even I have problem in typing my password. Whenever I try to save any webpage, it is bookmarked automatically. Whenever I copy, it is cut automatically. I have to spend more than half of time correcting what I have typed. Note: Typing thisd quwesdtion wasd rweally a big pain to mwe.

  Read the article

• How do I prevent my computer from freezing when it starts to swap?

  - by cdauth

  I work as a Java programmer, so I often have to run several programs at the same time that consume a lot of memory. When my memory is full and Linux starts swapping, my computer almost completely freezes. I can see that it is heavily writing on the hard-disk and everything reacts really slowly, often not at all. Moving the mouse in X sometimes doesn’t work at all, sometimes it has a delay of several seconds, clicking usually has a delay of several minutes. Sometimes it is possible to change to the TTY (with a long delay), there I can usually type without delay, but when I try to log in, it takes several minutes after typing in the user name until the password prompt appears, and usually an error message appears that tells me that the login timed out. So the only possibility is usually to restart the computer. I noticed that other intensive writing to the hard disk also significantly slows down my computer. Sometimes, I used rsync to limit the bandwidth when I copied files around on my own computer, as else the system would be almost unusable. How can this be? At the moment it seems more useful to me to completely turn off swapping. That might crash some processes, which is unfortunate, but the alternative at the moment is to crash all processes by turning off my computer. I am using Gentoo Linux with kernel 3.6.2-gentoo, I have a 10 GB swap partition on a HDD.

  Read the article

• What are the possible problems, when wget returns code 500 but same request works in normal browsers?

  - by markus

  What should I be looking for, when wget returns 500 but the same URL works fine in my web browser? I don't see any access_log entries that seem to be related to the error. DEBUG output created by Wget 1.14 on linux-gnu. <SSL negotiation info stripped out> ---request begin--- GET /survey/de/tools/clear-caches/password/<some-token> HTTP/1.1 User-Agent: Wget/1.14 (linux-gnu) Accept: */* Host: testing.thesurveylab.net Connection: Keep-Alive ---request end--- HTTP request sent, awaiting response... ---response begin--- HTTP/1.0 500 Internal Server Error Date: Wed, 12 Dec 2012 14:53:07 GMT Server: Apache/2.2.3 (CentOS) Set-Cookie: blueprint2-staging=8jnbmkqapl30hjkgo0u6956pd1; path=/ Expires: Thu, 19 Nov 1981 08:52:00 GMT Cache-Control: no-store, no-cache, must-revalidate, post-check=0, pre-check=0 Pragma: no-cache Strict-Transport-Security: max-age=8640000;includeSubdomains X-UA-Compatible: IE=Edge,chrome=1 Content-Length: 5 Connection: close Content-Type: text/html; charset=UTF-8 ---response end--- 500 Internal Server Error Stored cookie testing.thesurveylab.net -1 (ANY) / <session> <insecure> [expiry none] blueprint2-staging 8jnbmkqapl30hjkgo0u6956pd1 Closed 3/SSL 0x0000000001f33430 2012-12-12 15:53:07 ERROR 500: Internal Server Error.

  Read the article

• Trouble setting up incoming VPN in Microsoft SBS 2008 through a Cisco ASA 5505 appliance

  - by Nils

  I have replaced an aging firewall (custom setup using Linux) with a Cisco ASA 5505 appliance for our network. It's a very simple setup with around 10 workstations and a single Small Business Server 2008. Setting up incoming ports for SMTP, HTTPS, remote desktop etc. to the SBS went fine - they are working like they should. However, I have not succeeded in allowing incoming VPN connections. The clients trying to connect (running Windows 7) are stuck with the "Verifying username and password..." dialog before getting an error message 30 seconds later. We have a single external, static IP, so I cannot set up the VPN connection on another IP address. I have forwarded TCP port 1723 the same way as I did for SMTP and the others, by adding a static NAT route translating traffic from the SBS server on port 1723 to the outside interface. In addition, I set up an access rule allowing all GRE packets (src any, dst any). I have figured that I must somehow forward incoming GRE packets to the SBS server, but this is where I am stuck. I am using ADSM to configure the 5505 (not console). Any help is very much appreciated!

  Read the article

• How do I automatically connect my client to an ODBC data source on another machine with dynamic IP?

  - by Kdansky

  At the customer's place, we've got a postgres DB on a server, and a few clients. We connect them through ODBC-drivers, and all machines run windows (usually XP). Now we had a few annoying issues: The client "forgets" some flags in the ODBC drivers, such as ByteA as LO. Every time anything changes, we have to reset that, and type in the password, and sometimes even the IP of the server. On x64 machines running Windows 7, configuring this is a pain as the system settings dialogue will only show 64-bit connections by default. And most importantly: If the server changes IP because the customer restarts or replaces a switch, all connections are lost. Annoyingly, this cannot be fixed with just correcting the IP, but rather, we have to check every single place (even hba_conf) because all the settings magically disappear. Our customers often are very small companies, where "server" means "that one PC in the other room", and not "Oracle mainframe in the dungeon", so we don't want to rely on them not restarting switches. Is there a better way than to rely on these really unstable settings? Are these settings somewhere in a file which I could edit manually, to make fixing it easier?

  Read the article

• Is there any way to synchronize AD users with Office 365 but still be able to edit them online?

  - by Massimo

  I'm performing a migration to Office 365 from a third-party mail server (MDaemon); the local Active Directory doesn't include any Exchange server, and never had any. We will need directory synchronization in order to enable users to log on to Office 365 using their domain credentials; but it seems that as soon as you enable directory synchronization, you can't perform any action anymore on Office 365 users: all changes need to be made on the local Active Directory, and then replicated by the synchronization process. For ordinary users with a single e-mail address and standard features, this is not a big problem; but what about users which need an additional address? What if I need to configure some nonstandard setting, like "hide from address list" or a custom mailbox quota? From what I've gathered, the only supported way to do this, as you can't directly edit Office 365 objects anymore after synchronization is enabled, is to extend the local AD schema with Exchange attributes, and then manually edit them (!). Or, you can install at least one local Exchange server, and then use the Exchange administrative tools to configure the required settings. Is this correct or am I missing something? Is there any way to synchronize user accounts and password, but still be able to edit user settings directly in Office 365? If not (everything really needs to be set locally and then synchronized), is there any simpler way to do this than manually editing LDAP attributes or installing a local Exchange server?

  Read the article

< Previous Page | 410 411 412 413 414 415 416 417 418 419 420 421  | Next Page >