Search Results

Search found 18161 results on 727 pages for 'cell array'.

Page 416/727 | < Previous Page | 412 413 414 415 416 417 418 419 420 421 422 423  | Next Page >

• Tool to bulk speed up/convert an audio file

  - by User1

  I want to listen to certain podcasts on my phone but I have two common problems: The audio is in some weird format (some don't play on my phone). The audio is slow. I want to use something like sox or avconv to bulk convert the files. Since this is just voice and going on a cell phone, small low-quality files would be best for me. I had some good success using avconv: avconv -i weird.wma normal.ogg Unforunately, this command creates an enormous ogg file and I can't get it play faster. Ideally, this particular file would play at 170% of the original speed.

  Read the article

• How to properly remove disk from PERC 6/i RAID controller ?

  - by Stefano Borini

  I have a Dell T710, coming with PERC 6/i RAID controller. The current raid has 2x500 GB hard drives (with the OS), and 6x1000 GB hard drives (in RAID-6, currently empty). I would like to take one 1000 GB disk physically out to keep as an immediate spare in case of a crash, and configure the remaining 5x1000 GB in a single VD RAID-6. This is all nice and clean and works, until I realized that the display on the machine reports the lack of the 8th disk as an error. It's marked as error, but appears to be a warning, since the machine is fully functional. My question is: what is the best way to keep one disk as a spare out of the array? should I disassemble the disk from the cradle and insert the empty cradle in the array ? Or should I just silence the error in the display in some way (how?). I know that what I am doing sounds pretty strange, but here is academia and having a spare disk available could take weeks. Better to have one ready in my drawer for any emergency.

  Read the article

• HP DL185 - very slow disk read speed

  - by fistameeny

  Hi, I have a HP DL185 G6 Server (12 disk model) with the following spec: Quad Core Xeon 2.27GHz 6GB RAM HP P212 RAID controller with battery backup 2 x 128GB 15K SAS 3.5" (RAID-1 for the operating system) 4 x 750GB 7.5K SAS 3.5" (RAID-5 for the data, 2TB usable space) The operating system is Ubuntu Server 9.10. Both drives have been formatted as EXT4. We are finding that read speed of the RAID-5 array is poor. Disk test results below: sudo hdparm -tT /dev/cciss/c0d1p1 /dev/cciss/c0d1p1: Timing cached reads: 15284 MB in 2.00 seconds = 7650.18 MB/sec Timing buffered disk reads: 74 MB in 3.02 seconds = 24.53 MB/sec For info, the RAID-1 array performs as follows: sudo hdparm -tT /dev/cciss/c0d0p1 /dev/cciss/c0d0p1: Timing cached reads: 15652 MB in 2.00 seconds = 7834.26 MB/sec Timing buffered disk reads: 492 MB in 3.01 seconds = 163.46 MB/sec We thought this was because with no battery, read/write cache is disabled. We have bought and installed the battery backup and have used the HP bootable CD to change the cache settings to 50% read / 50% write and check cache is enabled on the drives and the controller. Is there something I'm missing?

  Read the article

• How to diagnose storage system scaling problems?

  - by Unknown

  We are currently testing the maximum sequential read throughput of a storage system (48 disks total behind two HP P2000 arrays) connected to HP DL580 G7 running RHEL 5 with 128 GB of memory. Initial testing has been mainly done by running DD-commands like this: dd if=/dev/mapper/mpath1 of=/dev/null bs=1M count=3000 In parallel for each disk. However, we have been unable to scale the results from one array (maximum throughput of 1.3 GB/s) to two (almost the same throughput). Each array is connected to a dedicated host bust adapter, so they should not be the bottleneck. The disks are currently in JBOD configuration, so each disk can be addressed directly. I have two questions: Is running multiple DD commands in parallel really a good way to test maximum read throughput? We have noticed very high SWAPIN-% numbers in iotop, which I find hard to explain because the target is /dev/null How shoud we proceed in trying to find the reason for the scaling problem? Do you thing the server itself is the bottleneck here, or could there be some linux parameters that we have overlooked?

  Read the article

• How ZFS handles online replacement in a RAID-Z (theoretical)

  - by Kevin

  This is a somewhat theoretical question about ZFS and RAID-Z. I'll use a three disk single-parity array as an example for clarity, but the problem can be extended to any number of disks and any parity. Suppose we have disks A, B, and C in the pool, and that it is clean. Suppose now that we physically add disk D with the intention of replacing disk C, and that disk C is still functioning correctly and is only being replaced out of preventive maintenance. Some admins might just yank C and install D, which is a little more organized as devices need not change IDs - however this does leave the array degraded temporarily and so for this example suppose we install D without offlining or removing C. Solaris docs indicate that we can replace a disk without first offlining it, using a command such as: zpool replace pool C D This should cause a resilvering onto D. Let us say that resilvering proceeds "downwards" along a "cursor." (I don't know the actual terminology used in the internal implementation.) Suppose now that midways through the resilvering, disk A fails. In theory, this should be recoverable, as above the cursor B and D contain sufficient parity and below the cursor B and C contain sufficient parity. However, whether or not this is actually recoverable depnds upon internal design decisions in ZFS which I am not aware of (and which the manual doesn't say in certain terms). If ZFS continues to send writes to C below the cursor, then we are fine. If, however, ZFS internally treats C as though it were gone, resilvering D only from parity between A and B and only writing A and B below the cursor, then we're toast. Some experimenting could answer this question but I was hoping maybe someone on here already knows which way ZFS handles this situation. Thank you in advance for any insight!

  Read the article

• Move every 3 rows into a column in excel

  - by Eliane El Asmr

  Please i need your help. I need to move every 3 rows into a new colomn. --Let's suppose i have this: Ambassade de France S.E. M. Patrice PAOLI 01-420000-420150 Ambassade de France Mme. Jamilé Anan 01-420000-420150 Ambassade de France Mme . Marie Maamari 01-420000-420150 --I need them to be Like this: Ambassade de France S.E. M. Patrice PAOLI 01-420000-420150 Ambassade de France Mme. Jamilé Anan 01-420000-420150 Ambassade de France Mme . Marie Maamari 01-420000-420150 I have this code. Can you help me Please. It's giving me error. Out of range. What should i change? It's urgent:(the code is for every 7, i need for every 3) Sub Every7() Dim i As Integer, j As Integer, cl As Range Dim myarray(100, 6) As Integer 'I don't know what your data is. Mine is integer data 'Change 100 to however many rows you have in your original data, divided by seven, round up 'remember arrays start at zero, so 6 really is 7 If MsgBox("Is your entire data selected?", vbYesNo, "Data selected?") <> vbYes Then MsgBox ("First select all your data") End If 'Read data into array For Each cl In Selection.Cells Debug.Print cl.Value myarray(i, j) = cl.Value If j = 6 Then i = i + 1 j = 0 Else j = j + 1 End If Next 'Now paste the array for your data into a new worksheet Worksheets.Add Range(Cells(1, 1), Cells(101, 7)) = myarray End Sub Thank you.

  Read the article

• Tools for displaying a multidimensional data table?

  - by ShreevatsaR

  [Apologies if this sort of question is off-topic for SuperUser. Please redirect to the right place if so.] There is a 3-dimensional array of values. (That is, instead of a table/2-dimensional array with values in a grid, the values can be thought of in a cube instead.) Is there a way to display this "cube" interactively, ideally on a webpage? Specifically, given the data, it would work something like this: the user selects two of the 3 variables. He then sees a "stack" of tables, one for each value of the third variable (cross-sections, in other words). By selecting the appropriate table from the stack, he can see the (i,j,k) value he wants. The "technology" for displaying such a thing (stacked tables, rotation, etc.) already exists, so this seems the sort of thing that someone ought to have written already. To be clear: I don't need sophisticated graphics necessarily, just the ability to select from cross-sections of variables. But I have no experience with (say, for displaying on a webpage) what web gadgets exist, so I'm clueless how to even search for one. (Google searches like "multidimensional data visualization" didn't throw up anything useful. Google Spreadsheets can do a few kinds of charts which can be embedded on a webpage, but I cannot tell if this is one of them.) [I can imagine how it ought to work for higher dimensions. For four-dimensions, instead of selecting just a stack, you'd first select an (i,j) from an "outer table", which would show all (k,l) values for that (i,j). For higher dimensions, inductively: you select (i,j), and then repeat what you'd do with 2 fewer dimensions.] So has this been written? Is this easy to write? Where ought one to look for such a thing?

  Read the article

• Positive result, negative result and current balance. How do you make starting balance show current result?

  - by Tine

  I have 3 columns. Column A shows positive result and if the result is negative then it is in a column B. Column B shows negative result and if the result is positive then it is in a column A. (meaning that either columns can have 0.00 in the cell (empty zero cells)). Column C has starting assets and it also shows the current balance that while result A or B are adding up and current balance is showing the current result. What is the proper formula for this I hope I was clear with my problem. Please help. Thanks in advance!

  Read the article

• What's a good way to share a value in multiple places in a Word document?

  - by jcollum

  Let's say I have a value: \\myServer\dir1\dir2\dir3. I'd like this value to appear in multiple places in an MSWord document. However I only want to write it down once. What's a good way to do this? Fields seem like the answer but I can't get it to work; maybe it's not the answer. I'd like to be able to do this without any macros; it adds too much complexity. I need something more like Excel -- write a cell value here, reference it there, change the original value and the reference gets updated too. Edit: ideally I'd have the value updated automatically (fields don't seem to want to do that!).

  Read the article

• How can I copy and paste formatted text in Excel?

  - by Landy

  Before I ask question, I've searched but only found ways of copy and paste "formatted cell". That's not what I need. I want to use an example to explain my requirement: There are 2 cells in a sheet. Cell_A's text is "aaaaabbbbb", and "aaaaa" is green, and "bbbbb" is red. Cell_B's text is "ccccc" and "ccccc" is black. I want to copy and paste "bbbbb" from Cell_A to Cell_B and keep "bbbbb" in red. But in my environment(Office 2007), "bbbbb" is changed to black as "ccccc", the default format of Cell_B. Is there an easy way to implement my requirement?

  Read the article

• Multidimensional data table?

  - by ShreevatsaR

  [Apologies if this sort of question is off-topic for SuperUser. Please redirect to the right place if so.] There is a 3-dimensional array of values. (That is, instead of a table/2-dimensional array with values in a grid, the values can be thought of in a cube instead.) Is there a way to display this "cube" interactively, ideally on a webpage? Specifically, given the data, it would work something like this: the user selects two of the 3 variables. He then sees a "stack" of tables, one for each value of the third variable (cross-sections, in other words). By selecting the appropriate table from the stack, he can see the (i,j,k) value he wants. The "technology" for displaying such a thing (stacked tables, rotation, etc.) already exists, so this seems the sort of thing that someone ought to have written already. To be clear: I don't need sophisticated graphics necessarily, just the ability to select from cross-sections of variables. But I have no experience with (say, for displaying on a webpage) what web gadgets exist, so I'm clueless how to even search for one. (Google searches like "multidimensional data visualization" didn't throw up anything useful. Google Spreadsheets can do a few kinds of charts which can be embedded on a webpage, but I cannot tell if this is one of them.) [I can imagine how it ought to work for higher dimensions. For four-dimensions, instead of selecting just a stack, you'd first select an (i,j) from an "outer table", which would show all (k,l) values for that (i,j). For higher dimensions, inductively: you select (i,j), and then repeat what you'd do with 2 fewer dimensions.] So has this been written? Is this easy to write? Where ought one to look for such a thing?

  Read the article

• SQL Management Studio is painfully slow on 32-bit Windows 7

  - by Sergei

  I've been having issues running anything in SQL Management Studio on Win 7. Basically, doing anything through the Management Studio interfaces completely freezes it up for a few minutes. Running a query is nearly impossible because it takes nearly 2 minutes just for the IDE to parse it and another minute to run it when the query itself completes instantaneously outside of the IDE. I'm not even going to go into the query designer. Anything with heavy user interaction such as editing a row in the result set where i have to click a cell freezes up the front-end. I tried reinstalling to no avail. Also tried running in compatibility mode without any difference whatsoever. Anybody had a similar experience? I'm running SQL Management Studio 2008 version 10.0.2531.0 on 32-bit Windows 7. Connecting to a remote SQL Server instance (2008 R2). Thanks.

  Read the article

• FreeNAS pool configuration - RAID1 + other drives

  - by trnelson

  Simple questions, really. I found this answer with a similar setup, but not sure it answers my question. If it does, I'm curious why since the answer seems a bit unsure: ZFS Hard Drive Configuration in FreeNAS I'm building a server which will be used primarily for backup, plus some media streaming, possibly with Plex. I seem to understand most everything I need, but I'm still a bit confused on how pools work, and how to configure them for my scenario. I will have 2x 2TB WD Red drives, which I plan on using in a mirrored set up (RAID1). This would be for backup, and I'd also like to do offsite backup to my CrashPlan account from this array. I also have a few other drives: 1.5TB, 320GB, 250GB. I'm not sure exactly what to do with them yet, but looking for options. FreeNAS OS will be running from a 16GB USB Flash drive. Would it be wise to use the 1.5TB as a backup-backup, essentially as a mirror or perhaps for snapshots of the 2TB RAID1? I'm still learning about snapshots. Should the 2TB mirrored drives be in their own pool? Should the other drives be set up in their own pools as well, or should they be JBOD in a single pool? They may or may not get much use since the 2TB array is plenty for me. Does a dataset basically mimic the idea of a partition or a network share? In other words, I would map \SERVER\Share to X: on my laptop? Let's say I wanted to use the 250GB drive as an encrypted drive to store all of my cat pictures. Would it have to be in its own pool? If I use jails apps, should they go in the backup RAID1, or in another place? Thank you!

  Read the article

• Mac Excel 2011: find Items in one column that are not in another column

  - by robert-jakobson

  Hi this is a repeat of the question: Excel: Find Items in one column that are not in another column I have two columns in excel, and I want to find (preferably highlight) the items that are in column B, but not in column A. What's the quickest way to do this? However, the answer given below to in the above-menitoned thread no longer applies to Mac Excel 2011. E.g. there is no "name-a-range" option available on right click etc.. Therefore I am asking this again. Select the list in column A Right-Click and select Name a Range... Enter "ColumnToSearch" Click cell C1 Enter this formula: =MATCH(B1,ColumnToSearch,0) Drag the formula down for all items in B If the formula fails to find a match, it will be marked #N/A, otherwise it will be a number. If you'd like it to be TRUE for match and FALSE for no match, use this formula instead: =IF(ISNA(MATCH(B1,ColumnToSearch,0)),FALSE,TRUE) How should this answer be restated to apply to Mac Excel 2011?

  Read the article

• Rebuilding LVM after RAID recovery

  - by Xiong Chiamiov

  I have 4 disks RAID-5ed to create md0, and another 4 disks RAID-5ed to create md1. These are then combined via LVM to create one partition. There was a power outage while I was gone, and when I got back, it looked like one of the disks in md1 was out of sync - mdadm kept claiming that it only could find 3 of the 4 drives. The only thing I could do to get anything to happen was to use mdadm --create on those four disks, then let it rebuild the array. This seemed like a bad idea to me, but none of the stuff I had was critical (although it'd take a while to get it all back), and a thread somewhere claimed that this would fix things. If this trashed all of my data, then I suppose you can stop reading and just tell me that. After waiting four hours for the array to rebuild, md1 looked fine (I guess), but the lvm was complaining about not being able to find a device with the correct UUID, presumably because md1 changed UUIDs. I used the pvcreate and vgcfgrestore commands as documented here. Attempting to run an lvchange -a y on it, however, gives me a resume ioctl failed message. Is there any hope for me to recover my data, or have I completely mucked it up?

  Read the article

• Converting a Windows 2003 server

  - by Jim Bass

  We have a legacy database system based upon MS SQL running on Windows Server 2003. The client software will only run on Windows XP. We have recently had success converting a client into a virtual machine and running it under Fusion on Mac minis. So far, it is working incredibly well. So well, in fact, that we are now considering trying to convert the server to a virtual machine. This raises several questions, though: 1. The server uses a raid array. Does the VM virtualize the raid array? I only ask because in my experience Windows products don't like it when you change core hardware. 2. Is there any reason why running SQL server on a virtual machine won't work? It will be up 24/7. 3. Is there a different converter for servers? 4. Will I have to track down the licensing for MS SQL and Server 2003 or will they come across ok? 5. The company that designed the software is no longer in business. There is some fear that the software is somehow tied to the hardware configuration. We bought the hardware, but their engineers came out and configured the system. Will the virtual machine be able to spoof particular chip sets? Thanks! Jim Bass

  Read the article

• In Open Calc, how do I copy a paste cells that contain references to other workbooks?

  - by Gabriel

  I have an OpenOffice Calc sheet with cells containing formulas that refer to another file, e.g: 'file:///C:/path/to/other.xls'#$Sheet1.A1:B2. Note: When I copy the cells from one sheet to another in the same workbookt, it works as expected. When I copy this to a sheet in another workbook, the references are lost and all is left is ''#$Sheet1.A1:B2. I could copy/paste the cell's contents, but that would be fastidious, error-prone, and anyhow not a good solution. How do I keep the external references when copy-pasting from one workbook to another ?

  Read the article

• Enterprise class storage best practices

  - by churnd

  One thing that has always perplexed me is storage best practices. Filesystems brag about how they can be petabytes or exabytes in size. Yet, I do not know many sysadmins who are willing to let a single volume grow over several terrabytes. I do know the primary reason behind this is how long it would take to rebuild the array should a drive fail. The more drives in a single LUN, the longer this takes and the greater your risk of losing another drive while the rebuild is taking place. Then there's usage reasons. Admins will carve out a LUN based on how much space they think needs to be allocated to the project. It seems more practical to me for the LUN to be one large array and to use quotas. I understand this wouldn't satisfy every requirement (iSCSI), but I see a lot of NAS systems (NFS) managed this way. I also understand that the underlying volumes can be grown/shrunk as needed quite easily, but wouldn't it be less "risky" to use quotas rather than manipulating volumes and bringing possible data loss into the equation? There may be some other reasons I'm missing, so please enlighten me. Can we not expect filesystems to ever be so large? Are we waiting for the hardware to get faster to cut down on rebuild times?

  Read the article

• Pivot Table from data with merged cells

  - by Graeme

  I have a energy spreadsheet for multiple sites. the first row has month and year. the next row has columns for date invoice received, KW hours and cost. So there are three columns for each month. I have merged the month cell across the three columns. When i create a pivot table the date kw/h and costs are labled date1, date2, etc. Can I link the months headings to the subheadings to get meaningful headings in the pivot table????

  Read the article

• Cannot view dates of emails(no date field), in my CSV file exported from MS Outlook

  - by barlop

  I am using Outlook 2010 - I have my emails showing in there. and exported my emails, into a csv file. (file..options..advanced...export..export to a file.. I have opened that csv file in excel Here is a list of the fields it shows. I see "Date" doesn't appear among them. Subject Body From: (Name) From: (Address) From: (Type) To: (Name) To: (Address) To: (Type) CC: (Name) CC: (Address) CC: (Type) BCC: (Name) BCC: (Address) BCC: (Type) Billing Information Categories Importance Mileage Sensitivity Any idea why "Date" isn't included, and how to include it? Also, (and less importantly, and as a very secondary issue) is there a convenient way to read the csv file? reading an email with a long body, in excel, is not convenient, I need to select all of the body from the cell and copy/paste it into notepad.

  Read the article

• script to list user's mapped drive not giving results or error

  - by user223631

  We are in the process of migrating two file servers to a new server. We have mapped drives via user group in group policy. Many users have manually mapped drives and we need to find these mappings. I have created a PowerShell script to run that remotely get the drive mappings. It works on most computers but there are many that are not returning results and I am not getting any error messages. Each workstation on the list creates a text file and the ones that are not returning results have no text in the files. I can ping these machines. If the machine is not turned on, it does come up error message that the RPC server is not available. My domain user account is in a group that is in the local admin account. I have no idea why some are not working. Here is the script. # Load list into variable, which will become an array of strings If( !(Test-Path C:\Scripts)) { New-Item C:\Scripts -ItemType directory } If( !(Test-Path C:\Scripts\Computers)) { New-Item C:\Scripts\Computers -ItemType directory } If( !(Test-Path C:\Scripts\Workstations.txt)) { "No Workstations found. Please enter a list of Workstations under Workstation.txt"; Return} If( !(Test-Path C:\Scripts\KnownMaps.txt)) { "No Mapping to check against. Please enter a list of Known Mappings under KnownMaps.txt"; Return} $computerlist = Get-Content C:\Scripts\Workstations.txt # Loop through each item in the array (each computer in the list of computers we loaded into the variable) ForEach ($computer in $computerlist) { $diskObject = Get-WmiObject Win32_MappedLogicalDisk -computerName $computer | Select Name,ProviderName | Out-File C:\Tester\Computers\$computer.txt -width 200 } Select-String -Path C:\Tester\Computers\*.txt -Pattern cmsfiles | Out-File C:\Tester\Drivemaps-all.txt $strings = Get-Content C:\Tester\KnownMaps.txt Select-String -Path C:\Tester\Drivemaps-all.txt -Pattern $strings -notmatch -simplematch | Out-File C:\Tester\Drivemaps-nonmatch.txt -Width 200 Select-String -Path C:\Tester\Drivemaps-all.txt -Pattern $strings -simplematch | Out-File C:\Tester\Drivemaps-match.txt -Width 200

  Read the article

• make file readable by other users

  - by Alaa Gamal

  i was trying to make one sessions for my all subdomains (one session across subdomains) subdomain number one auth.site.com/session_test.php session_set_cookie_params(0, '/', '.site.com'); session_start(); echo session_id().'<br />'; $_SESSION['stop']='stopsss this'; print_r($_SESSION); subdomain number two anscript.site.com/session_test.php session_set_cookie_params(0, '/', '.site.com'); session_start(); echo session_id().'<br />'; print_r($_SESSION); Now when i visit auth.site.com/session_test.php i get this result 06pqdthgi49oq7jnlvuvsr95q1 Array ( [stop] => stopsss this ) And when i visit anscript.site.com/session_test.php i get this result 06pqdthgi49oq7jnlvuvsr95q1 Array () session id is same! but session is empty after two days of failed trys, finally i detected the problem the problem is in file promissions the file is not readable by the another user session file on my server -rw------- 1 auth auth 25 Jul 11 11:07 sess_06pqdthgi49oq7jnlvuvsr95q1 when i make this command on the server chmod 777 sess_06pqdthgi49oq7jnlvuvsr95q1 i get the problem fixed!! the file is became readable by (anscript.site.com) So, how to fix this problem? How to set the default promissions on session files? this is the promissions of the sessions directory Access: (0777/drwxrwxrwx) Uid: ( 0/ root) Gid: ( 0/ root)

  Read the article

• Excel Help: Macro is not Cooperating with Quotations!!

  - by B-Ballerl

  Hi all, I Have a macro containing a line that will change the formula of a cell using R1C1 formula type. The formula is: ActiveCell.FormulaR1C1 = _ "=IF(R[0]C[-2]=0,"",(R[0]C[-20]-R[0]C[-16]))" When ever I attempt to run the macro it always comes up with a dialog box saying Run-time error '1004': Application-defined or object-defined error. And when you click debug it highlights those 2 lines in the macro. And I can't figure out how to fix it. Can anyone help?

  Read the article

• have list of emails to be deleted from sheet A col D [on hold]

  - by Peta

  Thank you for your comments guys & now that CharlieRB has suggested "Match entire cell contents" I'll give it a better go. No I do not expect people to do my work for me & I'm sorry if it came over that way - just didn't know where to start. Would love some help please, I've limited VBA & function knowledge & I'm not sure where to start. If someone can point me in the right direction it would be appreciated. I have a list of email addresses on sheet "B" col A (but I could put them on sheet A if it would make it easier / faster) that I want deleted from sheet "A" col D (may be 2 or more occurences of the same email). I can't just record a find & delete macro and edit because for example [email protected] will also pick up [email protected] which I may not want deleted. thanks very much Peta

  Read the article

• Backup data from RAID 1 disk out of its server

  - by Doomsday

  I'm facing with a pretty easy problem in my opinion. I've extracted a working disk from a RAID1 and I'm looking to copy only data (FS and RAID configuration doesn't matter) into another location (another FS). My problem is I'm not able to mount properly this disk into another linux. I've first looked the partition table : # fdisk -l /dev/sdc Disk /dev/sdc: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders, total 1250263728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 63 1249535699 624767818+ fd Linux raid autodetect /dev/sdc2 1249535700 1250017649 240975 fd Linux raid autodetect /dev/sdc3 1250017650 1250258624 120487+ 82 Linux swap / Solaris I've understood I should use dmraid tools. Once installed : # cat /proc/mdstat Personalities : md0 : inactive sdc1[1](S) 624767744 blocks unused devices: <none> And some other informations : # mdadm --examine /dev/sdc1 /dev/sdc1: Magic : a92b4efc Version : 0.90.00 UUID : 8f292f54:7e5aef72:7e5ab5fd:b348fd05 Creation Time : Mon Jun 2 03:39:41 2008 Raid Level : raid1 Used Dev Size : 624767744 (595.82 GiB 639.76 GB) Array Size : 624767744 (595.82 GiB 639.76 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Update Time : Tue Feb 7 22:34:59 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Checksum : a505b324 - correct Events : 15148 Number Major Minor RaidDevice State this 1 8 1 1 active sync /dev/sda1 0 0 8 17 0 active sync /dev/sdb1 1 1 8 1 1 active sync /dev/sda1 From here, I've tried to mount but I'm not comfortable with dmtools and how it's working. # mount /dev/sdc1 /mnt/sdc1 mount: unknown filesystem type 'linux_raid_member' # mount /dev/md0 /mnt/sdc1 mount: /dev/md0: can't read superblock I've seen some options to alter RAID array with mdadm but I only want to copy data on its filesystem before wiping them... Anyone has a clue ?

  Read the article

< Previous Page | 412 413 414 415 416 417 418 419 420 421 422 423  | Next Page >