Search Results

Search found 12829 results on 514 pages for 'hard'.

Page 416/514 | < Previous Page | 412 413 414 415 416 417 418 419 420 421 422 423  | Next Page >

  • Windows Server doesn't connect to a network share

    - by Dmitriy N. Laykom
    Windows Server doesn't connect to a network share. Network share is working. Blockquote Pinging 109.123.146.223 with 32 bytes of data: Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Ping statistics for 109.123.146.223: Packets: Sent = 3, Received = 3, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms net view \shareaddress Blockquote System error 53 has occurred. The network path was not found. When I connected the network share I observed this error message: Blockquote \ "Mapped disk letter" refers to a location that is unavailable. It could be on a hard drive on this computer, or on a network. Check to make sure that the disk is properly inserted, or that you are connected to the Internet or your network, and then try again. If it still cannot be located, the information might have been moved to a different location The network share was mounted via Group Policy. Perchance anyone knows how I can avoid this error? When the OS has been restored from the disk problem has been solved

    Read the article

  • troubleshooting postifx -> exchange connection issues

    - by Systemspoet
    I have three linux-based mail routers that run postfix and relay mail to our on-premise exchange server as well as to outlook.com, splitting the mail based on ldap atttributes. What I've observed sporadically since upgrading this spring from Exchange 2007 to 2010 is that all three of the mail relays will, for about 20 minutes, fail to connect to exchange. Postfix logs it as "lost connection with exchange.contosso.edu" ; this problem almost always occurs to all three mail relays at the same time, and lasts for slightly under 20 minutes. If I can catch it while it's occuring, and I manually do "telnet exchange.contosso.edu 25" from one mail relay and force a message through (helo, mail from, rcpt to, data, etc), then it clears that relay up. The exchange "server" is actually two machines with the HT role on them, load balanced via windows NLB. I've worked pretty hard to figure out what's happening from the postfix side and I can't see any evidence of any misbehavior. My question is, how do I attack the problem from the exchange side? Is there a connection log, or a debug setting, or something I can do to log all of the inbound connections and tell me what's causing exchange to drop them?

    Read the article

  • USB drive was bootable, but no longer isn't

    - by i-g
    I'm trying to install a new OS onto a computer from a bootable USB stick. I previously installed Ubuntu Linux and it was a piece of cake -- I downloaded the ISO image, used UNetbootin to copy it to the USB drive and make it bootable, and that was that. Now, however, no matter what I try, I can't make the same USB drive bootable again! I've tried formatting it as FAT32 and NTFS. I've tried several different Linux distributions and Windows 7. I've tried using UNetbootin, Windows 7 USB Download Tool, WinToFlash, and manually making it bootable with diskpart/bootsect/bootrec. (Yes, I've tried bootsect /nt60 x: /force.) None of this seems to be working! When I try to boot from the drive, the machine reads from it (I can see the drive's LED blinking) and then gives me the same "Insert system disk and press Enter" message. (I've disabled booting from the hard drive.) Am I missing something I need to do to make the USB drive bootable again? The USB drive in question is a SanDisk Cruzer 8GB SDCZ6. The computer I'm working on is running Windows Vista SP1.

    Read the article

  • Triple-Boot + 4 partition Limit

    - by dsimcha
    I just bought a new hard drive so that I could convert my XP-only machine into an XP-Ubuntu-Windows 7 triple boot machine. Since the drive is absurdly huge (1 TB) I wouldn't mind throwing ReactOS into the mix, too. I just found out that master boot records are limited to 4 entries, meaning 4 primary partitions. I had Windows XP set up on my old drive as a boot partition, a program files partition and a media partition. Since I really didn't want to install XP from scratch, I cloned this setup on my new drive. This leaves me one MBR partition entry for installing Windows 7, Ubuntu and ReactOS. I'd like to avoid having to install XP from scratch like the plague, partly because it's supposed to be a safety net in case things go wrong with my other OS's and because I've invested a lot of time getting it set up exactly the way I like it. Here are the options I've considered and why I don't like them: Install Windows 7 on my media partition. This would work, but I prefer to keep my media partition completely separate from any OS, so that I can reformat an OS partition without affecting my media partition at all. Use wubi or something to install Ubuntu in the same partition as something else. Again, this is brittle. Move all my media to a logical drive on an extended partition. Create another logical drive on this extended partition for Ubuntu. The problem here is that extended partitions are rather brittle--if you nuke one, it renders the rest useless. Just put the old drive back in my computer and run XP off it. Use the new one for the other OS's. The problem here is that the old drive is slower and uses extra power, generates extra heat, etc. Can anyone suggest any other possibilities that I may have overlooked?

    Read the article

  • How do I tell Windows to use 802.11 in preference to 3G?

    - by Jon Skeet
    I have a Samsung NC-10 netbook which I take to work every day. Most of the time I use it just on the train/bus, but I also use it at work and home. It has a built-in 3G card which I want to use when travelling, but I'd prefer to use wifi when I'm at work or home, for obvious reasons. Unfortunately, if the 3G connection is up, Windows appears to use that in preference to wifi. Starting up and shutting down the 3G modem is a bit of a pain - it's not hard as such, just a bit inconvenient. Ideally I'd like it to always be up, and even have the connection itself up all the time, but without routing traffic through it if there's a wifi connection up. This is what my Android phone does, for example. Is there somewhere in Windows which lets me express an ordering for network interfaces? I suspect the routing table may be relevant, but it's a bit of a pain to mess around with. I'd really expect there to be a simple GUI way of setting this up - after all, it would equally be useful when dealing with wired vs wifi connections. I'm currently using Windows XP Home, but Windows 7 answers would also be useful as I'll be migrating soon.

    Read the article

  • Cannot install windows. Compaq Presario CQ62

    - by Matthew
    I bought a used Compaq Presario CQ62 for cheap, and went to install windows on it. I formatted the partition and went to install when I got this error.... Windows cannot install required files. The file may be corrupt or missing. Make sure all files required for installation are available and restart the installation. Error code: 0x80070017 I have used this disk before with no problems, but internet searching suggested I burn one at 2x speed because that helps for some reason... I'm burning one now, but my question is, why would I get this error, OTHER than the disc being bad? I'm pretty certain this one isn't as I have used it before... (ok so the slowly burned cd (using imgburn) didn't work either so it's DEFINITELY not the disc) Thanks in advanced for any answers Also I took one stick of ram out because internet searching also suggested that, but it didn't make a difference. Also I ran memory and hard drive checks and they passed fine. Also I reset the motherboard options to default What could it be!? Help I'm completely stumped...

    Read the article

  • Windows 7 boot manager not localized on UEFI systems

    - by Massimo
    I originally posted this on SuperUser because I discovered this behaviour on my home computer, but this seems to be a general issue on UEFI systems, thus I'm posting here too; I also hope someone here can shed some light on what's going on. Italian version of Windows 7 x64 SP1, same installation media used for both situations. When running on BIOS systems, the boot manager is fully localized, both for the loading screen and for the F8 boot menu. When running on UEFI systems, the boot manager always runs in English, even if it's correctly configured to use the it-IT locale, as BCDEDIT clearly shows: Windows Boot Manager -------------------- identificatore {bootmgr} device partition=\Device\HarddiskVolume1 path \EFI\Microsoft\Boot\bootmgfw.efi description Windows Boot Manager locale it-IT inherit {globalsettings} default {current} resumeobject {9ef36aa6-4188-11e3-909d-d32f0c3871c8} displayorder {current} toolsdisplayorder {memdiag} timeout 30 Caricatore di avvio di Windows ------------------- identificatore {current} device partition=C: path \Windows\system32\winload.efi description Windows 7 locale it-IT inherit {bootloadersettings} recoverysequence {9ef36aa8-4188-11e3-909d-d32f0c3871c8} recoveryenabled Yes osdevice partition=C: systemroot \Windows resumeobject {9ef36aa6-4188-11e3-909d-d32f0c3871c8} nx OptIn I also noticed something strange here; the motherboard setup shows "Windows Boot Manager" as the main boot option, while the actual boot disk is listed as the second one. Looks like the Windows Boot Manager is actually being loaded from somewhere else than the first partition of the first disk... what's going on here? Update I've also checked the EFI boot manager using bcdedit /enum FIRMWARE. That one looks correctly localized, too: Boot Manager per firmware --------------------- identificatore {fwbootmgr} displayorder {bootmgr} {9ef36aa4-4188-11e3-909d-d32f0c3871c8} {a30e8550-47e4-11e3-9ad1-806e6f6e6963} timeout 1 Windows Boot Manager -------------------- identificatore {bootmgr} device partition=\Device\HarddiskVolume1 path \EFI\Microsoft\Boot\bootmgfw.efi description Windows Boot Manager locale it-IT inherit {globalsettings} default {current} resumeobject {9ef36aa6-4188-11e3-909d-d32f0c3871c8} displayorder {current} toolsdisplayorder {memdiag} timeout 30 Applicazione firmware (101fffff) ------------------------------- identificatore {9ef36aa4-4188-11e3-909d-d32f0c3871c8} description CD/DVD Drive Applicazione firmware (101fffff) ------------------------------- identificatore {a30e8550-47e4-11e3-9ad1-806e6f6e6963} description Hard Drive

    Read the article

  • After RAID failure SBS 2008 issues logging in and Exchange store does not mount

    - by Josh R
    today has been one of those days. Yesterday a hard drive in our Dell Poweredge 2900 server failed and the RAID array didn't degrade gracefully, so I called Dell (Server still under warranty) and got an engineer to work though the RAID issues with me. He was a nice guy but didn't do too much. We tried to put the RAID in a state where it was bootable and even though we only lost one disk there are still issues with the server. Once we got the server to boot there was an error message saying that the logonui.exe was corrupted and we needed to run chkdsk. I clicked through the error messages and the login screen never came up. So I power cycled the server and it chkdsk automatically but the login screen didn't appear. I tried safe mode, no difference there either. So the issues I am currently having are: 1) The server boots up, the loading windows screen comes up then it dumps me into a black screen where I can only see my mouse cursor. Ctrl+Esc doesn't work Ctrl+Alt+Del doesn't work 2) Some of the services come up: DHCP, DNS, DFS, and Print come up 3) The exchange information store and transport service don't start - I tried using mmc to connect to services.msc on the computer and start them but they throw an error message of "Can't start because group or dependency failed" Has anyone had a problem like this? Can anyone offer some guidance? Thanks a bunch!

    Read the article

  • Partition problem tyring to install window 7 starter

    - by ant2009
    Hello HP Mini 210 I am trying to install windows starter 7. Currently I have installed fedora 14 xfce. And I have allocated 24 GB NTFS for hard disk for the windows partition. My current partitions are as follows: /dev/sda2 97G 4.9G 91G 6% / tmpfs 494M 92K 494M 1% /dev/shm /dev/sda1 485M 68M 392M 15% /boot /dev/sda5 169G 26G 135G 16% /home I have created a boot USD to install windows starter 7. When the computer boots into the windows setup and I selected the partition I want to install windows on. I get the following message: "Setup was unable to create a new system partition or locate an existing system partition." This is setup displaying all my partitions: Disk 0 Partition 1 500MB 0 Primary Disk 0 Partition 2 97.7GB 0 Primary Disk 0 Partition 3 4GB 0 Primary Disk 0 Partition 4 171.3GB 0 Logical Disk 0 Partition 5 24.6GB 24.5 Logical <-- Trying install on this partition NTFS I have also tried to delete the partition in setup and create a new one. And also tried to format the partition. However, I still get the same error message. Many thanks for any advice,

    Read the article

  • Windows Server 2003 IPSec Tunnel Connected, But Not Working (Possibly NAT/RRAS Related)

    - by Kevinoid
    Configuration I have setup a "raw" IPSec tunnel between a Windows Server 2003 (SBS) machine and a Netgear FVG318 according to the instructions in Microsoft KB816514. The configuration is as follows (using the same conventions as the article): NetA | SBS2003 | FVG318 | NetB 10.0.0.0/24 | 216.x.x.x | 69.y.y.y | 10.0.254.0/24 Both the Main Mode and Quick Mode Security Associations are successfully completed and appear in the IP Security Monitor. I am also able to ping the SBS2003 server on its private address from any computer on NetB. The Problem Any traffic sent from a computer on NetA to NetB, or from SBS2003 to NetB (excluding ICMP Ping responses), is sent out on the public network interface outside the IPSec tunnel (no encryption or header authentication, as if the tunnel were not there). Pings sent from a computer on NetB to a computer on NetA successfully reach computers on NetA, but the responses are silently discarded by SBS2003 (they do not go out in the clear and do not generate any encrypted traffic). Possible Solutions Incorrect Configuration I could have mistyped something, somewhere, or KB816514 could be incorrect in some way. I have tried very hard to eliminate the first option. Have re-created the configuration several times, tried tweaking and adjusting all the settings I could without success (most prevent the SA from being established). NAT/RRAS I have seen multiple posts elsewhere suggesting that this could be due to interaction between NAT and the IPSec filters. Possibly the NetA private addresses get rewritten to 216.x.x.x before being compared with the Quick Mode IPSec filters and don't get tunneled because of the mismatch. In fact, The Cable Guy article from June 2005 "TCP/IP Packet Processing Paths" suggests that this is the case, (see step 2 and 4 of the Transit Traffic path). If this is the case, is there a way to exclude NetA-NetB traffic from NAT? Any thoughts, ideas, suggestions, and/or comments are appreciated.

    Read the article

  • USB drive was bootable, but no longer boots

    - by i-g
    I'm trying to install a new OS onto a computer from a bootable USB stick. I previously installed Ubuntu Linux and it was a piece of cake -- I downloaded the ISO image, used UNetbootin to copy it to the USB drive and make it bootable, and that was that. Now, however, no matter what I try, I can't make the same USB drive bootable again! I've tried formatting it as FAT32 and NTFS. I've tried several different Linux distributions and Windows 7. I've tried using UNetbootin, Windows 7 USB Download Tool, WinToFlash, and manually making it bootable with diskpart/bootsect/bootrec. (Yes, I've tried bootsect /nt60 x: /force.) None of this seems to be working! When I try to boot from the drive, the machine reads from it (I can see the drive's LED blinking) and then gives me the same "Insert system disk and press Enter" message. (I've disabled booting from the hard drive.) Am I missing something I need to do to make the USB drive bootable again? I think it lost some pixie dust when I formatted it with the standard Windows formatting tool (it was quicker than deleting files), but I have no idea what it was or how to get it back. The USB drive in question is a SanDisk Cruzer 8GB SDCZ6. The computer I'm working on is running Windows Vista SP1.

    Read the article

  • Is the Windows VPN secure?

    - by Tor Haugen
    I have used a few VPN solutions over the years. Most are hard to set up, slow to connect and/or rather ill-behaved (replacing system drivers, disrupting each other etc). One solution I have never used earlier is the one built into Windows. This is mostly because the infrastructure guys always refuse to use it because they claim it's 'not secure'. Now I have finally had the chance to use it (on Windows 7), and wow, it's a breeze! Easy to set up, well-behaved, it connects almost instantly, automatically authenticates with my logged-in credentials, and integrates excellently with the UI. I have to say, unless it really isn't secure, I'll be happy if I never have to use another VPN product ever again. I gather the Windows VPN used to rely on PPTP, which is not considered secure. But in Windows 7/2008, it supports L2TP/IPSec, SSTP and IKEv2, and authenticates with EAP or CHAP/CHAPv2. That seems pretty up-to-date to me. But I'm just a lowly developer. Can someone in the know give me the lowdown on this?

    Read the article

  • Is my motherboard failing, or is there some other issue?

    - by ThatGuy
    So, several months ago I put together my own desktop PC. I set up a dual boot to Windows and Ubuntu. Recently, without changing any settings or installing anything new, the wifi stopped working on windows (I use a wifi adapter). It said it was connected, Network settings showed that it was working and running trouble shooting had no results. My internet still works on any other device. I found that removing the adapter from the motherboard and plugging it back in was the only thing that fixed the problem. Reinstalling the wifi drivers did not help. I purchased a new Wifi adapter, but the problem persists. More recently, I had a much more discouraging development. Sometimes, turning on the computer results in a boot loop: BIOS never starts. Instead, the monitor turns on as if it got a signal, then immediately turns off. This loops on it's own indefinitely until I hold down power, hard reset it, and try again. Sometimes it works, sometimes it doesn't. I haven't tested much on the Ubuntu side. It appears that wifi works at least some of the time, but since I've had issues just getting to BIOS I'm not confident the issue is on the software side. I've also noticed issues with some of the USB ports no longer working, but that seems to be off and on. Finally, as of a few minutes ago, I booted to windows to discover that everything was running very slowly. Slow here is a relative word, but I have a Samsung 840 pro SSD and I'm used to applications running nigh instantly, and it was a solid 3 minutes before any of my applications would load. Anyway, my question is this: Is it likely that my motherboard is failing? Either way, what steps can I take to try and pin down the problem and figure out what to do?

    Read the article

  • Windows 7 breaks even in safe mode

    - by delenda
    Hi, I have a Dell XPS M1730 with Windows 7 installed. I noticed last night that after a few hours of use, the fans kicked into full and I couldn't do anything without it taking forever. Minimising windows, opening device manager or even opening process explorer took minutes and a game install I had just started took nearly 4 hours to complete. When procexp finally loaded, the refresh was so slow that it was mostly useless. From what I could gather, it was reporting 60% idle processes with procexp using nearly 40%. There were no hardware interrupts listed. When I rebooted, the problem went away for about 10 minutes and then the same thing happened. The issue persists in safe mode and even after I removed the graphics drivers, which have been an issue in the past, it still happens. Icons flash quite quickly on the desktop periodically and screen refresh is painfully slow. When booting now, the fans kick in to full as soon as the windows logon box comes up and it's taking 10 minutes to bring the desktop up. Chkdsk reports nothing and the raid check says that everything is fine. I'm thinking hardware failure, probably HDD but wanted some other opinions. I'm planning to try a linux live cd to see if it works without using the hard disks. If anyone has any input, it would be greatly appreciated. Delenda

    Read the article

  • S.M.A.R.T. broken sectors

    - by Jeffrey Vandenborne
    Recently I received my hard drive (LaCie) that I've sent away for warranty, my disk failed, and I used Palimpsest Disk utility to check if anything was wrong in the S.M.A.R.T Status. And it said that there were a few broken sectors. So the next day, I went to the store and told the story. 4 weeks later I actually got my drive back. The first thing I did was plugging it in and starting the disk utility, and weirdly it showed me pretty much the exact same things, even the values of most tests were the same as they were before when my drive broke. The serial number is different though, but it does show a very peculiar value. Now I'm wondering, I'm almost sure it's the exact same drive and it still says I've got broken sectors, does it just say that because it has been cached in the drive somewhere while LaCie DID actually fix it? Or should I run the extended self test (which seems to take hours) first? Also I've tried the smartctl command tool, it says the drive has smart support, but it doesn't show anything, it says that it's enabled, but then it says that it's disabled, picture below The picture of the Disk utility: Thanks in advance

    Read the article

  • a disk read error occurred [closed]

    - by kellogs
    Hi, ¨a disk read error occurred¨ appears on screen after choosing to boot into Windows XP from GRUB. [root@localhost linux]# fdisk -lu Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x48424841 Device Boot Start End Blocks Id System /dev/sda1 63 204214271 102107104+ 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 204214272 255606783 25696256 af HFS / HFS+ Partition 2 does not end on cylinder boundary. /dev/sda3 255606784 276488191 10440704 c W95 FAT32 (LBA) Partition 3 does not end on cylinder boundary. /dev/sda4 276490179 312576704 18043263 5 Extended /dev/sda5 * 276490240 286709759 5109760 83 Linux /dev/sda6 286712118 310488254 11888068+ b W95 FAT32 /dev/sda7 310488318 312576704 1044193+ 82 Linux swap / Solaris sda is a 160GB hard disk with quite a few partitions and 3 OSes installed. I am able to boot into Linux and Mac OS fine, but not into Windows anymore. The Windows system is located on /dev/sda1. I can not recall how exactly have I used testdisk but it once said that ¨The harddisk /dev/sda (160GB / 149 GB) seems too small! (< 172GB / 157GB)¨ or something simillar. So far I have tried to ¨fixboot¨ and ¨chkdsk¨ from a recovery console on the affected windows partition (/dev/sda1), the plug off power cord for 15 seconds trick, reinstalling GRUB, repairing the MFT and boot sector of the affected partition via testdisk, what next please ? Thank you!

    Read the article

  • MacBook Pro (2007 - ATI-Card) Screen goes half black then shuts down the entire computer

    - by BluePerry
    Hey, when I'm starting my MBP I get about 10-60 seconds of the booting process before the screen goes half black (Its like applying a black to transparent gradient from the left side of the screen to the middle of the screen). After a 5 seconds the entire screen blacks out and the MBP shuts down. There have been issues with heat and some minor artifacts on the screen in the past but nothing serious as far as I know. Everything could be resolved by rebooting or letting the MBP cool down a bit. I would like to identify the problem now. There are 3 possibilities I can think of right now: My graphics card is defect and shuts down after a few seconds. (But if thats true, I find it kind of hard to explain the HALF black screen) My LCD-Panel is defect and sends back wrong signals so the system shuts down??? (I not sure about that) My fan or/and thermal sensors are defect and forcing the graphics card to shut down. Can anyone point if I'm right or if there yet another reason for this. I'd be thankful for any hint or tips. Cheers, Per

    Read the article

  • How to delete removed devices from a mdadm RAID1?

    - by Kabuto
    I had to replace two hard drives in my RAID1. After adding the two new partitions the old ones are still showing up as removed while the new ones are only added as spare. I've had no luck removing the partitions marked as removed. Here's the RAID in question. Note the two devices (0 and 1) with state removed. $ mdadm --detail /dev/md1 mdadm: metadata format 00.90 unknown, ignored. mdadm: metadata format 00.90 unknown, ignored. /dev/md1: Version : 00.90 Creation Time : Thu May 20 12:32:25 2010 Raid Level : raid1 Array Size : 1454645504 (1387.26 GiB 1489.56 GB) Used Dev Size : 1454645504 (1387.26 GiB 1489.56 GB) Raid Devices : 3 Total Devices : 3 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Tue Nov 12 21:30:39 2013 State : clean, degraded Active Devices : 1 Working Devices : 3 Failed Devices : 0 Spare Devices : 2 UUID : 10d7d9be:a8a50b8e:788182fa:2238f1e4 Events : 0.8717546 Number Major Minor RaidDevice State 0 0 0 0 removed 1 0 0 1 removed 2 8 34 2 active sync /dev/sdc2 3 8 18 - spare /dev/sdb2 4 8 2 - spare /dev/sda2 How do I get rid of these devices and add the new partitions as active RAID devices? Update I seem to have gotten rid of them. My RAID is resyncing, but the two drives are still marked as spares and are number 3 and 4, which looks wrong. I'll have to wait for the resync to finish. All I did was to fix the metadata error by editing my mdadm.conf and rebooting. I tried rebooting before, but this time it worked for whatever reason. Number Major Minor RaidDevice State 3 8 2 0 spare rebuilding /dev/sda2 4 8 18 1 spare rebuilding /dev/sdb2 2 8 34 2 active sync /dev/sdc2

    Read the article

  • How to back up initial state of external backup drive?

    - by intuited
    I've picked up an HP Simplesave external drive. It comes with some fancy software that is of no use to me because I don't use Windows. Like many current consumer-targeted backup drives, the backup software is actually contained on the drive itself. I'd like to save the drive's initial state so that I can restore it if I decide to sell it. The backup box itself is somewhat customized: in addition to the hard drive device, it presents a CDROM-like device on /dev/sr0. I gather that the purpose of this cdrom device is to bootstrap via Windows autoplay the backup application which lives on the disk itself. I wouldn't suppose any guarantees about how it does this, so it seems important to preserve the exact state of the disk. The drive is formatted with a single 500GB NTFS partition. My initial thought was to use dd to dump the disk (/dev/sdb) itself, but this proved impractical, as the resulting file was not sparse. This seemed to be because the NTFS empty space is not filled with zeroes, but with a repeating series of 16 bytes. I tried gzipping the output of dd. This reduced to the file to a manageable size — the first 18GB was compressed to 81MB, versus 47MB to tarball the contents of the mounted filesystem — but it was very slow on my admittedly somewhat derelict Pentium M processor. The time to do that first 18GB was about 30 minutes. So I've resorted to dumping the disk state and partition data separately. I've dumped the partition state with sfdisk -d /dev/sdb > sfdisk.-d.out I've also created a compressed image of the NTFS partition (the only one on the disk) with ntfsclone --save-image --output - /dev/sdb1 | gzip -c > ntfsclone.img.gz Is there anything else I should do to ensure that I can restore the precise original state of the drive?

    Read the article

  • PST backup with Volume Shadow Copy Service

    - by NoMadMan
    I was asked to implement the task of backing up 35 PST files ranging from 800Mb to 2000Mb. Windows XP and Windows 2000 workstations are assigned to the users and we have a Windows 2000 domain controller we use to back up files on 3x 500Gb external hard drives. I found several methods from applications to scripts. Local or remote applications would be my last resort. I came across this script based on Volume Shadow Copy Service. CopyWithVss I wanted to know if there would be a problem if the path had spaces. Would mounting the destination path of each PST folder with a drive letter be more practical? My concern with mounting option is that i would eventually run out of letters since I have 35 and possibly more workstations to back up. Lastly, can someone give me an example of CopyWithVss if it were run on a production network? The script is a bit cryptic even after reading several times. Where in the script do I enter the source and the destination? I'm a Mac user so please excuse my ignorance with Windows platform.

    Read the article

  • Recovering a broken NTFS filesystem?

    - by OverTheRainbow
    A much-needed Windows Update broke a Vista laptop that was running fine until then: After booting up, Windows displays "Please wait..." but it never goes anywhere. I waited for a couple of hours, there is a bit of disk activity, but it didn't work out in the end. I booted with the Vista DVD, chose "Repair your computer" which said that there was nothing wrong :-/ Next, I booted it up with a Linux USB keydrive, and ran Gparted 0.8.1 (which includes ntfsresize v2011.4.12AR.4 libntfs-3g) which displays a bunch of warnings for the NTFS partition where the Vista system is located such as: ntfs_mst_post_read_fixup: magic: 0x00000000 size: 1024 usa_ofs: 0 usa_count: 65535: Invalid argument Record 16 has no FILE magic (0x0) Next, I ran ntfsfix /dev/sda2, which said: Mounting volume... OK Processing of $MFT and $MFTMirr completed successfully. NTFS volume version is 3.1. NTFS partition /dev/sda2 was processed successfully. Next, I rebooted Vista, which did a CHKDSK, before rebooting. But I'm still getting nowhere with "Please wait..." Before I copy the user's data to another host and reinstall Vista from a DVD, does someone know what I could try? Thank you. Edit: In case someone else has the same issue... After the BIOS, hit F8 and choose "Repair your computer", followed by "Toshiba HDD Recovery". In addition to a 1,5GB partition labelled "WinRE", the hard disk contains a second partition labeled "Data" from which the application will fetch a system image and reinstall it in the "Vista" partition. Make sure you copy your data out of the system partition before doing this.

    Read the article

  • Windows 8 install from USB freezes

    - by Rafael Almeida
    I'm trying to install Windows 8 from an 8GB Kingston Data Traveler. I'm currently using the Windows 7 USB DVD Download Tool to put the iso into the flash drive. It copies the files, but in the end it says it 'had a problem with bootsect' and could not make the flash drive bootable. This seems to be because my current system is Windows 7 32bits, and the bootsect.exe in the ISO is a 64-bit executable. Then I downloaded the 32-bit bootsect.exe and made the drive bootable by running: bootsect /nt60 E: /mbr Then I restarted and managed to boot via the flash drive, but now everything is very slow. It takes about two minutes for the initial black screen with the Windows logo and the spinner go away, then it goes to a purple-ish blank screen that stays on for about five more minutes and then it finally shows a dialog asking for the installation, date/time and keyboard languages. I input then, click "Install Now" and it takes about three more minutes with a "Setup is starting" screen. After that, the PC apparently reboots, the CPU fan speeds up considerably, and there's no video and nothing more happens even after more than ten minutes. What is happening? I already tried using another USB port and even installing from a Samsung G3 Station 2TB external hard disk, but the same thing happens. The file transfer speed to the Kingston drive was about only 3 megabytes per second.

    Read the article

  • HP DL380 G3 2U For Basic Web Server in 2012

    - by ryandlf
    I have an opportunity to pick up a used HP DL380 G3 2U for $100. I'm looking for a basic entry level web server that I can host a small - medium size website on and more or less learn the ins and outs of running my own web server before I bite the bullet and spend a couple grand on a server. The specs are: Dual (2) Intel Xeon 2.4GHz 400MHz 512KB Cache 4GB PC2100 ECC Registered Memory 6 x 72GB 10K U320 SCSI Hard Drives Smart Array 5i RAID Controller Redundant Power Supplies DVD/Floppy, Dual Intel GB NIC's, USB Or would I be better off spending a couple hundred bucks on something like: this new HP Seems like the only major difference is SATA and a bit of storage, but I will likely be implementing a separate storage system of some sort anyways. I guess it also wouldn't hurt to mention that I plan on running a linux server distro, so would the hardware be likely to support linux with a system that is 4 generations old? I don't mind spending a couple hundred extra dollars if its a better solution, but as mentioned previously I am simple looking for a server to learn on and probably use for a year or so while I put together a small - medium size website.

    Read the article

  • Deleting old system folders from a drive that is no longer the windows installation drive

    - by grenade
    I dropped my laptop and was no longer able to boot. There were error messages about a corrupt boot record. Replacing the hard drive and reinstalling Win 7 was how I dealt with it. The old drive still appears to be good and I can read and write to it when I connect it as a second drive and mount as D:. However, if I try to recover the space being used by the windows, programdata, program files & program files(x86) folders, by deleting them I get error messages about needing permission from trustedinstaller. If I set myself as the owner of the folders and retry the delete I get error messages about needing permission from myself! Since I'm pretty sure that I have permission from myself to delete the folders, I can only assume that the OS or file system has gotten its panties twisted. I have tried shift, right click, delete from explorer and also if I run "del /f /s /q D:\Windows" from an admin command prompt, I get a succession of Access is denied messages as well. How do I delete D:\Windows, D:\ProgramData, D:\Program Files & D:\Program Files(x86) from a drive that is not the Windows installation drive?

    Read the article

  • What is the name of the this DOS font? Where and how to add it? Why is there a 1 pixel gap?

    - by JBeurer
    So basically I somehow stepped into this webpage: www.braindamage.vg And the first thing that hit me hard was the lovely DOS fonts, so naturally I wanted to get them into my IDE badly. Opened the html source file and CSS file to find the font name: @font-face { font-family: 'Perfect DOS VGA 437'; src: url('http://www.braindamage.vg/wp-content/themes/braindamage/dosfont.eot'); } @font-face { font-family: 'Perfect DOS VGA 437'; src: url('http://www.braindamage.vg/wp-content/themes/braindamage/dosfont.svg#dos') format("svg"), url('http://www.braindamage.vg/wp-content/themes/braindamage/dosfont.ttf') format ('truetype'); } So I download the font, add it using Control Panel - Fonts. But once I start using it (notepad, MSVS 2008 & MSVS2010) I notice that it looks slightly off: It seems like there's 1 extra pixel between each character. How it should look: What is causing it and how to fix this? Is it the windows XP? (i have disabled font smoothing) Or is there something wrong with the font file?

    Read the article

< Previous Page | 412 413 414 415 416 417 418 419 420 421 422 423  | Next Page >