Search Results

Search found 32567 results on 1303 pages for 'test manager'.

Page 416/1303 | < Previous Page | 412 413 414 415 416 417 418 419 420 421 422 423  | Next Page >

• VLAN issues between linux kernels 2.6 / 3.3 in an ESX / Cisco environment

  - by David Griffith

  I shall attempt to explain an issue I have encountered - I have a VM running on esx 4.1 with an interface connected to VLAN800 via an access port on a cisco 3750. It runs linux - kernel 2.6.24, and has about 5 to 10 Mbit of chatter on 10.10.0.0/16 and various multicast addresses to look after. I needed to isolate certain devices from certain other devices on the network, with all of them having to talk to that one VM. No, the address space can't be separated, nor can the networks be easily vlan'd apart. The software on the VM listens to one interface only. Private vlans appear to be the way to go. So as a test, I built a bridge on the VM that globs together the vlans as needed. All good, everything works as expected. But occasionally (sigh) there's some latency that trips up a couple of profinet devices on the network because, you know, you're not really supposed to trunk real-time protocols around the place willy-nilly. I shift it to our test/backup server - works nicely, but I don't want it to be running on the test server as we muck around with that a lot. So I says to myself, "I'll put it on a new VM for testing and tweaking." I download a small linux distro with kernel 3.3, and install as a new VM with a the vlans as separate interfaces for testing. I power up the testing VM - ok. I bring up all the separate interfaces - ok. I can ping the production VM, see all sorts of traffic going past with tshark, etc. I build a bridge and put the primary vlan on it - the production VM running 2.6 immediately loses its multicast traffic - Unicast is fine. (?) I shut down the bridge - still no multicast traffic (!?) I power-cycle the production VM(!?!?) - multicast traffic returns. I trunk everything into the testing VM and create vlan interfaces under linux instead - same result, as soon as I start the bridge.... no multicast on the production VM. Ok, so I take a break and leave things alone. I decide to play with a couple of ubiquiti bullet radios - I'm testing various firmware as a side project. I flash a radio with Open-wrt-12.09. I enable a trunk on a port on a cisco on our network so I can muck around with multiple vlans and SSIDs I power up the radio and connect - ok. I create a vlan interface from the trunk.... the same vlan as the production VM wayyyyy over there, three cisco routers away. Ok. I bridge the vlan interface to the wifi interface and immediately get a phone call. The production VM has (suprise!) lost its multicast traffic. Again, nothing comes back until I power-cycle the VM. What the hell is going on?

  Read the article

• nginx: location, try_files, rewrite: Find pattern match in subfolder, else move on?

  - by Nick

  I'd like for Nginx to do the following: If the uri matches the pattern: http://mysite.com/$string/ and $string is not 'KB', and not 'images', look for $string.html in a specific subfolder. If $string.html exists in the subfolder, return it. If it does not exist, move on to the next matching location. $string = {any letters, numbers, or dash} For example, if the user requests: http://mysite.com/test/ It should look for a file called: /webroot/www/myfolder/test.html I've tried variations of: location ~ /[a-zA-Z0-9\-]+/ { try_files /myfolder/$uri.html @Nowhere; } But: It doesn't seem to find the file even when it does exist, and If it fails (which is always right now), it wants to jump to the @nowhere location, rather than moving on and trying to find another location that matches. I'd like for it to consider the current location "not a match" if the file doesn't exist.

  Read the article

• Valid path to deploy vm on host

  - by ELSheepO

  I've recently added a VM to the library in SCVMM to use with MS Test Pro 2010, and run into a problem. I cannot import it using test pro, it just won't give me any option to import in the lab manager. Also, if I try to deploy it back to the host it came from, it gives me a error saying the path is not valid. Anyone have any insight into this? Also, SCVMM seems to freeze everytime I try to create a new VM from the template of the VM I've stored in the library, the same one thats giving me the problem when I try to deploy it on to the host. Thanks.

  Read the article

• What makes you look like a bad developer (ie a hacker) [on hold]

  - by user134583

  This comes from a lot of people about me, so I have to look at myself. So I would wonder what make one a bad developer (ie a hacker). These are a few things about me I used IDE intensively, all features, you name it: auto-completion, refactoring, quick fixes, open type, view hierarchy, API documentation, etcc When I deal with writing code for a project in domain I am not used to (I can't have fluency in this, this is new), I only have a very rough high level ideas. I don't use the standard modeling diagrams for early detail planning. Unorthodox diagrams that I invented when I need to draw the design in details. I don't use UML or similar, I find them not enough. I divide the sorts of diagram I drew into 3 types. Very high level diagrams which probably can be understood by almost anybody. Data entity diagram used for modeling data objects only (like ER diagrams and tree for inheritances and composition). Action diagrams for agents/classes and their interactions on data objects they contain. Constantly changing the interface (public methods) between interacting agents/classes if the need arises. I am more refrained when the interface and the module have matured Write initial concept code in a quick hackie way just so that the module works in the general cases so that I can play around with it. The module will be re-factored intensively after playing around so I could see more corner cases that I couldn't or (wouldn't want) anticipate before writing code. Using JUnit for integration-like test by using TestSuite class and ordering Unit test classes in the suite Using debugger almost anytime there is a problem instead of reading the code Constantly search on the internet for how to do some thing with some library that I haven't used a lot. So judgment, am I a bad developer? a hacker? Put in other words, to make sure this is not considered off-topic: - Is this bad practice to make your code too agile during incubating/prototyping phase of software development - Is it bad practice to use JUnit for integration testing, (I know there are other framework for integration testing, but those frameworks are for a specific products, not general)

  Read the article

• finder restore window error

  - by corne

  my mac with lion starts up with the finder dispaying the message to "restore window" and keep on cycling thru it but never opening the finder window. other sites say that file/s in my desktop folder is corupt and i must delete them fith terminal. there is no way to open the terminal app in my normal user profile. i have created a test user profile with administative rights and that works fine but the problem is my normal desktop folder is locked and not accesiable in my test user account. how do is delete those files in my normal desktop folder with the terminal app?

  Read the article

• Exchange 2010 Prevent Authenticated Users From Sending Email From Any Address

  - by Chance

  I have recently been combating an SMTP AUTH attack in which one of my email accounts had been compromised and was being used to solicit spam. I have been able to identify the account and change the password however I would like to further restrict my exchange server. By default exchange 2010 allows for any authenticated user to specify any email address as the MAIL FROM address and it will accept it. Is there any way to restrict this so that only the authenticated account's email address will be able to be used as the MAIL FROM address? I have been looking through all ADPermissions for the SMTP connector however I can't find any documentation on how to accomplish this. Any suggestions would be greatly appreciated. Telnet Test Picture Telnet Test SMTP Connector Properties Pictures Permissions Tab

  Read the article

• have 2 exchange servers to communicate together!

  - by Data-Base

  we have our exchange server 2007 (10.10.2.11) at work with domain "dddddd.com" and ironport and it work just fine! we need to test some thing at work with Exchange 2010 !! so we came up with this idea: we created a locked network and install firewall (10.10.2.88) the locked network has it's own DC and Exchange servers! we used the domain "dddddd.loc" any way it will be deleted! IPs DC 10.0.0.1 EX 10.0.0.11 now the Exchange server up and running in the firewall (10.10.2.88) we opened the ports and forwarded it to the Exchange2010 (10.0.0.11) in our main DC we defined the zone dddddd.loc to the firewall and the MX records as well but when we test we get error now how to make it so that the 2010 will send email directly to the 2007 (we will not use it to more that that)? and the 2007 will send the email to 2010 if the email has the domain dddddd.loc ?

  Read the article

• RDA version 4.28 released

  - by THE

  Oracle proudly presents: RDA 4.28  This version of RDA comes with a new HCVE rule set (pre installation checks) Doc ID 1435695.1 now alsocollects Calc Manager Information Enjoy a faster resolution and clear communication about what Software is installed, the logs retrieved and have Tech Support react faster to the issue at hand by getting a detailed overview of the system they are dealing with. More information about RDA in general can be found here.

  Read the article

• Mac Snow Leopard Server DNS

  - by panomedia

  I have a Tomcat-driven application on my Windows server that I am planning to move to a MacMiniServer. Before I do this, I want to fully test the transition for licensing purposes. I have a Fire drive setup with Snow Leopard Server and the base app runs just fine BUT I need to be able to resolve the URL to my domain and not localhost. So, I figured I would setup panomedia.net in the DNS Server and also create an A record to my internal network IP so www.panomedia.net would dish out the same thing as localhost. The problem is: The Tomcat web app starts up going through panomedia.local and not through www.panomedia.net and My main network preference panel is still looking at my Comcast DNS search providers even though I put my local IP address as the only DNS Server and Search provider. I need to test this via an actual domain name before I commit to a 400GB data move. Can anyone help?

  Read the article

• Developing a TCK: Spec Lead Call for Spec Leads 20 December

  - by Heather VanCura

  The JCP Program will be hosting a Spec Lead call on 20 December on the topic of developing a Technology Compatibility Kit (TCK).  A Technology Compatibility Kit is a required output of a JSR at Final Release, along with the Specification and Reference Implementation (RI).   The TCK must test all aspects of a specification that impact how compatible an implementation of that specification would be, such as the public API and all mandatory elements of the specification. The Reference Implementation is required to pass the TCK. A vendor's implementation of a specification is only considered compatible if the implementation passes the TCK fully and completely.  The TCK is used to test implementations of the Final Specification to make sure that they are fully compatible. The call will be recorded and posted on the JCP.org multimedia page along with any related materials.   Invitation details for the online meeting:Topic: SL Call: Developing a TCK Date: Thursday, December 20, 2012 Time: 9:30 am, Pacific Standard Time (San Francisco, GMT-08:00) Meeting Number: 804 390 892 Meeting Password: 2222 ------------------------------------------------------- To join the audio conference -------------------------------------------------------     +1 (866) 682-4770 (US)     Conference code: 945-4597    Security code: 52775 ("JCPSL" on your phone handset)     For global access numbers see http://www.intercall.com/oracle/access_numbers.htm         Or +1 (408) 774-4073

  Read the article

• Apache+FastCGI Timeout Error: "has failed to remain running for 30 seconds given 3 attempts, its restart interval has been backed off to 600 seconds"

  - by Sadjad Fouladi

  I've recently installed mod_fastcgi and Apache 2.2. I have a simple cgi script as below (test.fcgi): #!/bin/sh echo sadjad But when I invoke 'mysite.com/test.fcgi' I see "Internal Server Error" after a short period of time. The error.log file shows this error message: [Tue Jan 31 22:23:57 2006] [warn] FastCGI: (dynamic) server "~/public_html/oaduluth/dispatch.fcgi" has failed to remain running for 30 seconds given 3 attempts, its restart interval has been backed off to 600 seconds This is my .htaccess file: AddHandler fastcgi-script .fcgi RewriteEngine On RewriteCond %{REQUEST_FILENAME} !-f RewriteRule ^(.*)$ django.fcgi/$1 [QSA,L] What could the problem be? Is it my .htaccess file?

  Read the article

• Is there any trick to join and use Windows 8/8.1 with Samba 4 (4.1.6)?

  - by tenshimsm

  It seems that Samba doesn't like at all. I've followed various tutorials and I can't get Windows 8 to work properly with a Ubuntu Server as domain controller. This week i've downloaded ubuntu 14.04 lts and set a fast domain configuration. As usual all other Windows version (XP and 7) work but the newest M$ nightmare doesn't. In this try it doesn't even join the domain, keeps saying the my username or password are wrong. My /etc/samba/smb.conf # Global parameters [global] workgroup = DOMAIN realm = DOMAIN.LAN netbios name = DOM server role = active directory domain controller dns forwarder = 8.8.8.8 idmap_ldb:use rfc2307 = yes [netlogon] path = /var/lib/samba/sysvol/domain.lan/scripts read only = No [sysvol] path = /var/lib/samba/sysvol read only = No [test] directory mode = 0750 path = /SHARES/test read only = no Does anyone have a tutorial that really works? Because I've tried many, each one with different configurations that works only with the people that made them. And is there a way to import my old AD users, computers and ID in a way that I won't need to rejoin all computers?

  Read the article

• ionice idle is ignored

  - by Ferran Basora

  I have been testing the ionice command for a while and the idle (3) mode seems to be ignored in most cases. My test is to run both command at the same time: du <big folder> ionice -c 3 du <another big folder> If I check both process in iotop I see no difference in the percentage of io utilization for each process. To provide more information about the CFQ scheduler I'm using a 3.5.0 linux kernel. I started doing this test because I'm experimenting a system lag each time a daily cron job updatedb.mlocate is executed in my Ubuntu 12.10 machine. If you check the /etc/cron.daily/mlocate file you realize that the command is executed like: /usr/bin/ionice -c3 /usr/bin/updatedb.mlocate Also, the funny thing is that whenever my system for some reason starts using swap memory, the updatedb.mlocate io process is been scheduled faster than kswapd0 process, and then my system gets stuck. Some suggestion? References: http://ubuntuforums.org/showthread.php?t=1243951&page=2 https://bugs.launchpad.net/ubuntu/+source/findutils/+bug/332790

  Read the article

• C# .Net Utility suggestion for personal computer laptop

  - by alliswell

  Hi all, I want know what are utilities you have created for your personal computer or laptop for day to day purpose. Like few may have created task manager or windows service for scheduler, or tool to get latest feeds from SO. Need your experiences, which made your day to day task easier. And I don't want to know any third party(except Commercial) tools. I will not commercialize this ;-), but I want to know how I can utilize my skills to create application for personal use.

  Read the article

• rewrite map (prg:) never finishes

  - by SooDesuNe

  using Apache and a prg type rewrite map. My map looks like: #!/usr/bin/perl $| = 1; # Turn off buffering while (<STDIN>) { print "someothersite.com"; } the rewrite rule declared in httpd.conf is: RewriteMap app_map prg:/file/path/test.pl RewriteRule (\/[\w]+)(\/[^\#\s]+)?$ http://${app_map:$1}$2 [P,L] And the log files show: init rewrite engine with requested uri /a/testlink.html applying pattern '(\/[\w]+)(\/[^\#\s]+)?$' to uri '/a/testlink.html' It appears like test.pl is never giving control back to apache, when the map is successfully found I expect to see this output in the log file: map lookup OK: map=app_map key=/a -> val=someothersite.com Why is my map not returning control back to apache?

  Read the article

• Avast not taking any action when opening a virus.

  - by ULTRA_POROV

  I just did a test with the EICAR test virus. I downloaded the file eicar.com Avast was on. If i scan the file it finds it. However if i open it no action is taken. Just nothing. nothing happens i can open it as many times as i want. This is very worrying. The new avast is starting to be a pain. I miss the old one.

  Read the article

• IPv6 feature in Network Adaptor is Slowing Internet

  - by Teknophilia

  The past few days, my internet browsing has become very poor. It's not a matter of speed, as a speed test will give at least 15Mbps. It seems as if my laptop has a hard time actually connecting to the sites. I've found a possible culprit, but don't know why it would affect anything: Going to adapter settings and disabling ipv6, but leaving ipv4, my browsing is back to normal. Re-enabling ipv6 brings back the issue. This is strange though, because I have always had ipv6 enabled. Moreover, using sites to test ipv6 compatibility, I fail with ipv6 enabled on my adapter, and pass when it's disabled. Ideas about why this is happening, and how to fix it?

  Read the article

• Groovy 2.0 : plus statique pour un meilleur dynamisme, Invoke Dynamic, vérification des types et compilation statiques sur la première bêta

  Groovy 2.0 : plus statique pour un meilleur dynamisme Invoke Dynamic, vérification des types et compilation statiques sur la première bêta [IMG]http://idelways.developpez.com/news/images/groovy.jpg[/IMG] L'équipe du projet Groovy surprend la communauté du langage en sortant la version 2.0 en bêta, alors que c'est la 1.9 qui était attendue. Comme c'est tendance actuellement, Groovy abandonne la numérotation des versions majeures en deuxième position (1.x), où la version 2.0 devient « mythique et semble ne jamais vouloir arriver », explique Guillaume Laforge, manager du projet. Le projet aura désormais une évolution majeure chaque année, mais cette versi...

  Read the article

• Why my sub-domain redirect returns a blank page?

  - by Tom Brito

  I have the domain http://dropbox.tombrito.com/ (on GoDaddy) forwarding with masking to www.dropbox.com/sh/k6ypvx4y4kf0gu6/rdjxQ1b1OL It was working fine some time ago, but now the result is a blank page (although the Dropbox's favicon appears correctly in the browser's tab title). The DNS manager shows me a single entry with the name "dropbox": A dropbox 64.202.189.170 Any idea what's wrong? Related: Why my domain redirect on Google Apps is returning 404?

  Read the article

• Enablement 2.0 Get Specialized!

  - by mseika

  Enablement 2.0 Get Specialized! The Oracle PartnerNetwork Specialized program is releasing new certifications on our latest products, and partners are invited to be the first candidates to get certified. Oracle's Certified Exams go through a rigorous review process called a "beta period". Here are a few advantages of taking a Beta Exam: Certification exams taken during the beta period count towards company Specializations. Most new Certified Specialist Exams have no training requirement. Beta Exams Vouchers are available in limited quantity, so request a voucher today by contacting the Partner Enablement Team and act fast to reserve your test from the list below. FREE Certification Testing Are you attending OPN Exchange @ OpenWorld? Then join us at OPN Specialist Test Fest! October 1st - 4th 2012, Marriott Marquis Hotel Pre-register now! Beta testing period will end on October, 6th, 2012 for the following exams: Oracle E-Business Suite R12 Project Essentials (1Z1-511) Beta testing period will end on October, 13th, 2012 for the following exams: Oracle Hyperion Data Relationship Management Essentials (1Z1-588) Beta testing period will end on November, 17th, 2012 for the following exams: Oracle Global Trade Management 6 Essentials (1Z1-589) Exams Coming Soon in Beta Oracle Fusion Distributed Order Orchestration Essentials Exam (1Z1-469) Take the exam(s) now at a near-by Pearson VUE testing center! Contact Us Please direct any inquiries you may have to the Oracle Partner Enablement team at [email protected] For More Information Oracle Certification Program Beta Exams OPN Certified Specialist Exam Study Guides OPN Certified Specialist FAQ

  Read the article

• VLC stream with trickplay

  - by marjasin

  The idea is to start a video stream from one computer and watch it on another with the ability to start/stop the stream. I think I could do this with VLC but i haven't been able to figure out how. I've tried the following: (From the official forum) Stream with RTSP and RTP: on the server, run: % vlc -vvv input_stream --sout '#rtp{dst=192.168.0.12,port=1234,sdp=rtsp://server.example.org:8080/test.sdp}' on the client(s), run: % vlc rtsp://server.example.org:8080/test.sdp But this doesn't give me the ability to start/stop the stream from the client. According to the VLC release note something called "Trick play" was added in version 1.0. This seems to be what I'm looking for but i can't find any documentation that descibes how to use it.

  Read the article

• How can I tell if a host is bridged and acting as a router

  - by makerofthings7

  I would like to scan my DMZ for hosts that are bridged between subnets and have routing enabled. Since I have everything from VMWare servers, to load balancers on the DMZ I'm unsure if every host is configured correctly. What IP, ICMP, or SNMP (etc) tricks can I use to poll the hosts and determine if the host is acting as a router? I'm assuming this test would presume I know the target IP, but in a large network with many subnets, I'd have to test many different combinations of networks and see if I get success. Here is one example (ping): For each IP in the DMZ, arp for the host MAC Send a ICMP reply message to that host directed at an online host on each subnet I think that there is a more optimal way to get the information, namely from within ICMP/IP itself, but I'm not sure what low level bits to look for. I would also be interested if it's possible to determine the "router" status without knowing the subnets that the host may be connected to. This would be useful to know when improving our security posture.

  Read the article

• Windows 8.1 erased Ubuntu 14.04 partition

  - by Caumons

  I had Ubuntu 14.04 installed with a Windows 7 dual boot. Now, I've just replaced W7 by Windows 8, but the Ubuntu partition has disappeared! Running fdisk -l doesn't show /dev/sda5 (which was the Ubuntu partition), if I access to Gparted, it shows the Ubuntu partition as "empty space" and from Windows 8's device manager, this partition also appears as empty space! WTF has happened here? Has the partition been actually erased?

  Read the article

• Windows 7 booting and startup repair issues

  - by aardvark

  I have a MSI FR720 laptop with Windows 7 and Lubuntu partions. For quite a while (6 months or so) I've been having issues booting from my hard drive, it'd take me between 5 minutes and several hours for me to be able to have it recognize the hard drive as a bootable device. I did several disk checks on it, and my hard drive seems in perfect condition, and the fact that booting would usually only work after removing the hard drive and trying to reset it in its slot or lightly shaking it makes me think it had something to do with the connection in the hard drive slot as opposed to the hard drive itself. I was having particular issues with it detecting the hard drive today so I decided to try booting it from an external hard drive dock. It detected it first try and so far has had no problems finding the bootable partitions on my hard drive. When I selected my Windows 7 partition from the boot menu it said that it hadn't been shut down properly last time and needed startup repair. I've done this several times over the last 6 months, so this is hardly unusual. I do startup repair, it fails, and then I try to do a system restore. The system restore also failed, and it says that no files were changed. I restart and try it again. However, this time when I get to the startup repair it's not detecting a Windows OS. I tried clicking next and doing a startup repair but the repair is always failing. If I ignore the startup repair option and instead select "Launch windows normally" it will get to the windows animation, stop halfway through and then crash into a BSoD. I can't read the error on the screen because it immediately switches to back and tries to restart. This is my first time asking a question like this online, so let me know if I need to provide any extra information and I'll do my best to give it I tried using diskpart to find the list of partitions and see if one's labelled as an active partition, but it says that no disk were detected. I can run Lubuntu just fine. I can also see all of my Windows 7 files from it EDIT: The startup repair diagnosis and repair log is this: -- Number of repair attempts: 1 Session details System Disk = Windows directory = AutoChk Run = 0 Number of root causes = 1 Test Performed: Name: Check for updates Result: Completed successfully. Error code = 0x0 Time taken = 15ms Test Performed: Name: System disk test Result: Completed successfully. Error code = 0x0 Time taken = 31ms Root cause found. If a hard disk is installed, it is not responding. -- Any chance that this is a result of me doing this through an external dock through a USB drive?

  Read the article

• database independent coding framework options?

  - by statirasystems

  Background: I have not programmed in a while besides doing VBA and a little VB.NET. So please forgive my language use. I'm green and have a head cold. I am reading all I can now, but I have no programming circles to draw from. The information I am providing is to help guide you to what I am looking for. I am not confident I can ask the question properly. Story: I have four different projects that I am starting. Obviously I won't be working on all at the same time however they each will have similar needs and be inter related. They are as follows: Desktop Environment/System User Interface - basically a product that runs on major computers via mono or .net that unifies the look and functions. In the context of the up coming question it would be able to directly access data of various types. It would work in tandum with my office suite, system manager, and network application framework. Office Suite - technically it would not be a suite since I will be doing it from one interfacel except for the Communications Application. As far as the question, it will need to be able to link to various data sources for storing files and using, manipulating, and presenting information. System Manager - an intellegent system to manage and administer the entire network and all equipment. As far as the question, needs to be able to access data for archiving and and for accessing it's own settings stored in various formats, sql or xml. Network Application Framework - A complete system that can be used for ERP, CRM, CMS, Errata, File Management, and so on. As to the question to be able to access it's own or interlink with existing applications. Requirement: C#, Simplifies and reduces coding, use the same code to access diffent databases(ie MySQL, MS SQL, ACCESS, XML, ...), Mono would be nice but not a must, Question: What librarys, frameworks, or other options would be able to help with this? Is there a good resource to guide me? I don't want arguing over what is best, just information to help me further understand and make an educated decision.

  Read the article

< Previous Page | 412 413 414 415 416 417 418 419 420 421 422 423  | Next Page >