Search Results

Search found 12588 results on 504 pages for 'memory allocation'.

Page 421/504 | < Previous Page | 417 418 419 420 421 422 423 424 425 426 427 428  | Next Page >

• Windows 7 Startup fails after installation

  - by Nadav S.

  I have installed Windows 7 Ultimate a week ago. Yesterday I've noticed that the SP1 update is available. After installation of SP1 the computer failed to startup, and had shown a black screen. I couldn't even go to safe mode and F8 didn't help. After some fixing attempts including system restore, startup repair, bootmgr & BCD rebuilding from CMD, I have decided to reinstall Windows (after all, it's only a week old) After the successful installation, I have decided to first install all available updates before I continue. So after the updates download & installation, the computer rebooted. And now I didn't see the black screen again - but in the "Starting Windows..." screen the logo didn't appear and the system didn't startup. Here I could go to safe mode selection window, but it didn't work either ("Loading Windows Files" but nothing). I've also tried: I thought that the CD was corrupted, so I've used a fresh new disk of Windows, tried x86 & x64 versions, the same symptoms, no change. Resetted the BIOS to default, no change. Memory diagnostic HDD diagnostic Restarted Windows WITHOUT INSTALLING UPDATES, but it had the same symptom, so maybe Windows Update is not the case?! I've tried installing it so many times - that I am simply stuck - I can't "reinstall Windows, because it is corrupted...". Maybe the HDD is corrupted? I've also checked it and didn't find a problem.

  Read the article

• Windows 7 starts getting sluggish over a few days

  - by munrobasher

  Myself and the other developer are running Windows 7 Enterprise 64 bit with 8GB RAM on different Gigabyte motherboards with Quad core Intel CPUs. Most of the time, it runs like a dream. We use VMware workstation a lot (hence the 8GB) and that works well. Except... now and then, after the PCs have been on for a few days, the whole system starts getting really sluggish doing certain tasks. The other's developer's system is far worse than mine with it taking up to a minute to launch IE. Today, mine has gone sluggish but nowhere near as bad. For example, normally when I click on a new tab in IE, it's instant. Today, there's an obvious delay. Right-clicking in this window to trigger iSpell is normally instant, right now it takes about five seconds. I've got resource monitor open on my second monitor and when I did that right-click, there was no obvious peak in CPU, disk or memory. A reboot does fix it so it does sound like a resource issue but haven't a clue what might be to blame. The two computers have similarities (same spec) but also differences (like motherboard, RAM & CPU models). So I guess the question is, any pointers on diagnosing why a PC is sluggish? What could cause such a right-click slow down in IE for example? It sounds like such a simple operation. NOTE: whilst typing this message alone, it was fine performance wise. I can click around the page no problem but right-click still is noticeable slow. Will reboot over lunch... Cheers, Rob.

  Read the article

• Help, my CentOS servers keep going down , No route to host after a random uptime

  - by user249071

  Hello , I have a couple of Centos linux servers, that have a very simple task, they run nginx + fastcgi for php , and some NFS mounts between them, readonly They have some RPC commands to start some downloading processes with wget, nothing fancy , from a main server, but their behavior is very unstable, they simply go down, we tried to monitor ram , processor usage, even network connections, they don't load up so much, max network connections up to... 250 max, 15% processor usage and memory , well, doesn't even fill up, 2.5GB from 8GB max , I have no ideea why can a linux server go down like that, they aren't even public servers, no domain names installed no public serving, for sites. The only thing that I've discovered was that if i didn't restart the network service every couple of hours or so... the servers were becoming very slow, starting apps very slow, but not repoting a high usage of resources...Maybe Centos doesn't free the timeout connections, or something like that...It's based on Red Hat right? I'm not a linux expert , but I'm sure that there are a few guys out there that can easily have an answer to this , or even have some leads to what i can do ... I haven't installed snort, or other things to view if we have some DOS attacks, still the scheduled script that restarts the network each hour should put the system back online, and it doesn't.... Thank you in advance

  Read the article

• mod_fcgi in virtualmin: graceful kill fail, sending SIGKILL?

  - by mgjk

  Yesterday around 1am, our server ground to a crawl. This doesn't happen often, but I'm trying to get to the bottom of it. There is no unusual traffic volume, no unusual processes running, just all of the sudden the server started killing fcgid processes. [Thu Aug 02 01:17:32 2012] [warn] mod_fcgid: process 26460 graceful kill fail, sending SIGKILL ... for as many fcgid processes as we have... CPU idle fell to 0% and I/O seemed to take up most of the load. The issue lasted about 5 minutes. I suspect there was some swap activity, although I'm not sure if it was due to killed processes being swapped in to die, or if it was because some process ramped up memory usage faster than my process watching scripts can see them. The oom-killer wasn't triggered (at least it's not logged), so I think this was Apache for some reason restarting the processes. This is not regular, and nothing obvious appears in cron. Is there a normal Apache process which might cause this? We run dozens of different sites, and it was late at night, so volume was very, very low. (maybe 200 requests in a 10 minute period).

  Read the article

• VMware Workstation "Power off" and "Suspend" buttons are disabled. What is going on?

  - by Ed Norris

  I've been using an XP image for a few months now with no problems. Recently the power off and resume buttons were disabled and I'm not sure what happened to cause that. In addition, the menu items to do those functions are grayed out (like VM | Power | Power Off) I'm using VMware Workstation 6.5.3 on a Windows 7 64-bit host. The image is Windows XP 32-bit. There is plenty of free space and memory on the host and the CPU is not pegged. I am able to power off the image through its Start menu, but that's a workaround not a fix. Any suggestions? TIA EDIT: Well after manually shutting down the image then closing and reopening the image file (which I've done before) in preparation for reinstalling the tools as suggested below, it looks fine. The power off and suspend buttons are enabled and work. So what do I do with this question now? "Close and restart a few times and it may work" doesn't seem useful...

  Read the article

• then an error occurred during the login process - Connection Error 233

  - by scott brunner

  We have SQL Server 2008 installed on 64Bit Windows Server 2003. When we try connect to the local SQL Server using SQL Server Management Studio at the console, we get the error: A connection was successfully established with the server, but then an error occurred during the login process. provider: Shared Memory Provider, error: 0 - No process is on the other end of the pipe. When we try TCP from same local SSMS to local server, we get the same error but intead of the pipe message its something like "connection forcibly closed". Now, here is the strange part - we CAN connect to this SQL Server from any other machine on the network using SSMS. - AND - WE CAN'T connect to ANY SQL Server from the problem server. So it seems the SQL Server instance is fine and accepting remote connections. However, the SSMS on that machine will not connect to any SQL Server even remotely. When we try an ADO.NET connection from C# remotely we can connect, run that same code on the console of the trouble server and we get the same errors. How can this be solved?

  Read the article

• How to better copy&paste big files over RDP?

  - by WebMAOhist

  Recently I was making a few attempts to copy&paste a big (1.2 GB) file to remote computer over RDP. The remote computer is virtual testing machine with MS Windows Server 2008 Datacenter. First I tried to copy&paste before midnight when the transfer speed was limited by client computer ISP to 100 kB/s. So, it required a few hours and I was forced to cancel transfer since remote desktop became too unresponsive and sluggish (slow). So, I re-started it over midnight when my local transfer speed is over 4 GB/s 4MB/s (sorry for typo). So, my impression is that independently on speed (broadband) of copy&paste transfer the remote computer becomes sluggish while copying over RDP. At the same time downloading from internet doesn't make remote host sluggish. AFAIU, it is because clipboard of remote computer and so its memory becomes overloaded by transfer. How can I control (restrict) the usage of clipboard for specific process (pasting of file)? What are the possible way to control it? Update: After reading that slow speed of transfer is caused by encryption used for copy&pasting over RDP and since I believe I am more interested in overall efficiency: both the time, or rapidness, of getting file as well as possibility to work without waiting, I changed the question title from: How to control the usage of remote desktop clipboard usage for pasting a big file? to How to better copy&paste big files over RDP? For example, is it better to copy&paste one huge (zip) archive or unzip it and copy paste a folder with unzipped files? And more exactly I wanted to ask: What are possible ways to improve overall experience: the speed of transfer (i.e. availability of needed file) responsiveness of remote host (making remote coputer available for work before completion of copy&pasting)?

  Read the article

• Windows 7 64-bit Google Chrome Makes Desktop Unresponsive

  - by Meengla

  For the past 1-2 weeks my desktop becomes unresponsive sometimes. The problem seems to happen as I load a page in Google Chrome; it could be any page though today it happened when I tried to load a page with Flash content in it. The problem is not consistent and there is no pattern. I can do a virus scan using some software (not antivirus installed--never needed that) but I strongly suspect it is some software I installed or some Windows Update. This is a very powerful Dell Optiplex 990 with 16GB RAM, so Memory shouldn't be an issue. When the problem happens the cursor becomes spinning even over the taskbar and control alt delete takes a long time. Eventually I get a message that 'this program is not responding' with end/close and 'cancel' icon. But repeated end or cancel does nothing. Then the menu for ctrl alt del comes up. The rest of the applications keep running fine though I can't get to them because the cursor is the wait-cursor. What is happening? How can I find what exactly caused the problem? Thanks.

  Read the article

• Performance decrease in every game and application

  - by Márk Vincze

  When I start a game, initially it runs smoothly, but after a couple of minutes, the performance gradually decreases to the point of being unplayable (1-2 FPS). The sound also starts to lag at this point. This does not happen every time I start my PC, usually exiting the game, rebooting, then starting the game again solves the problem, and I can play with perfect FPS for as long as I want. I could not find any deterministic reason when this happens and when doesn't. It happens in every game I tried (SWTOR, Diablo 3, Skyrim), and not even games, but simple applications like a browser or the Control Panel can get unusably slow. This is a brand new PC I bought three months ago, and this problem occurs since the first day I've been using it. Could you provide any advice how to further diagnose the problem? I tried to reinstall Windows, and tried different video card drivers, but it did not help. It would be important to know whether this is a hardware or software problem, because I can use the warranty if it is a hardware issue. (I did not want to return the PC yet, because I can't reproduce the issue deterministically.) Spec of the pc: Motherboard: ASROCK H61M-HVS CPU: INTEL Core i3-2120 3.30GHz 1155 BOX Memory: KINGMAX 4096MB DDR3 1333MHz KIT Video card: GIGABYTE GV-R685OC-1GD HD6850 1GB GDDR5 PCIE HDD: SEAGATE 500GB Barracuda 7200rpm 16MB SATA3 ST500DM002 I am using Windows 7 64 bit. Thanks a lot in advance!

  Read the article

• Connections to SSH and Samba suffer from heavy delay

  - by Till Helge Helwig

  There are a lot of questions about SSH connections being delayed, which usually can be fixed by disabling the DNS lookups. Unfortunately this doesn't seem to be my problem. Our development server is accessed via SSH and Samba. When opening a connection to the server (either SSH or Samba) it takes a very long time. Accessing a Samba share via Windows is basically impossible because there is a timeout. Using smbclient works, but takes ages. When opening a SSH connection I get immediately prompted for the password and after hitting Enter the terminal instantly shows the MOTD. Afterwards it takes about a minute for the prompt to appear. I watched the load of the server while connecting via SSH and Samba and could not find anything out of order. There is nothing out of the ordinary running and hogging up memory and CPU or something. I have no clue where this delay might come from. I already tried UseDNS no in sshd_config and proxy_dns = no in smb.conf, but to no avail. Any idea about what might cause this would be greatly appreciated!

  Read the article

• Linux boot - stop the kernel switching to a new framebuffer mode clearing output

  - by Avio

  I'm working on an embedded system (based onUbuntu 12.04 LTS) and I'm customizing its kernel. I'm having some problem with upstart, mountall and plymouth. Nothing unsolvable I suppose, but the real problem is that I can't diagnose properly what's going on because the kernel (or maybe plymouth) changes the video mode in the middle of the boot process. This completely wipes entire lines of log and prevents any debugging of kernel misconfigurations. My Grub2 config seems to be ok with: GRUB_CMDLINE_LINUX="" GRUB_CMDLINE_LINUX_DEFAULT="acpi=force noplymouth" GRUB_GFXMODE=1024x768x32 GRUB_GFXPAYLOAD_LINUX=keep Here is some relevant output of lspci: 00:00.0 Host bridge: Intel Corporation Mobile 945GSE Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GSE Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) And here is the relevant portion of my kernel configuration: CONFIG_AGP=y CONFIG_AGP_INTEL=y CONFIG_VGA_ARB=y CONFIG_VGA_ARB_MAX_GPUS=16 CONFIG_DRM=y CONFIG_DRM_KMS_HELPER=y CONFIG_DRM_I915=y CONFIG_DRM_I915_KMS=y CONFIG_VIDEO_OUTPUT_CONTROL=y CONFIG_FB=y CONFIG_FB_BOOT_VESA_SUPPORT=y CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y CONFIG_FB_MODE_HELPERS=y CONFIG_FB_VESA=y CONFIG_BACKLIGHT_LCD_SUPPORT=y CONFIG_BACKLIGHT_CLASS_DEVICE=y CONFIG_VGA_CONSOLE=y CONFIG_VGACON_SOFT_SCROLLBACK=y CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=640 CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y CONFIG_FONT_8x8=y CONFIG_FONT_8x16=y CONFIG_LOGO=y CONFIG_LOGO_LINUX_MONO=y CONFIG_LOGO_LINUX_VGA16=y CONFIG_LOGO_LINUX_CLUT224=y Every other custom/stock kernel boot fine with that Grub2 config. What I would like to have is a single flow of messages on a single console (retaining one screen resolution) from the bootup logo till the login prompt. Does anybody know what I have to tweak to achieve this?

  Read the article

• Turn computer into DAS (Direct Attached Storage)

  - by Damon

  Can we build a direct attached storage by taking a computer/server, adding an HBA, and installing some appropriate software? We would use Debian as a host OS for both the DAS and the server. If so, what software do we use? And do we simply need a HBA for the DAS and the Server? Or do we need more hardware? The goal is to use an older server that does not have enough room for drives but does have ECC memory, server processors, redundant power supplies, dual nics, etc. Then find any boxes, server or not, the key being having enough room for 8-12 drives, fans, etc. and turning them into a DAS; build two of these DAS's and have them connected to the server. Eventually we want to have two servers using DRBD and associated services like heartbeat and pace maker to create an HA setup for our server(s) but that will take a long time to configure since I have no experience with anything related to DRBD (yet) and have a learning curve I have to get past, not to mention the additional cost of more hardware (two servers vs one).

  Read the article

• Computer hangs at BIOS screen. Cannot enter setup

  - by d2jxp

  I have an HP Pavilion a6500f (it's a year out of warranty) and it's hanging on the blue HP BIOS screen. If I mash F10 while it's starting up, it will say "Entering Setup..." but I will see no results. It will hang there and not do anything. If I actually wait until I can see the screen and then hit F10, there's no response at all and the computer will sit at the BIOS menu. I've dusted and cleaned it out, reseated the memory, switched the RAM slots, and reset the CMOS battery using the reset jumper. I'm out of ideas. I'm pretty sure it's not a hard drive issue, since my problem is at the BIOS. After this post, I'll disconnect the hard drive and try to just boot without it. Anyone have any other ideas? Edit: Okay, so I tried disconnecting the hard drive and now I can get back into the BIOS. I reconnected it and I'm locked out again. So the problem is my hard drive.. I guess I should delete this post unless someone has any ideas as to what's wrong with the drive?

  Read the article

• MAMP Pro mysqld won't start on os x lion

  - by Mike

  getting a Start MySQL Failed error in the GUI.. when i attempt to start mysqld from the CLI i get the following error: ? /Applications/MAMP/Library/bin/mysqld 120623 23:12:47 [Warning] Setting lower_case_table_names=2 because file system for /Applications/MAMP/db/mysql/ is case insensitive 120623 23:12:47 [Note] Plugin 'FEDERATED' is disabled. 120623 23:12:47 InnoDB: The InnoDB memory heap is disabled 120623 23:12:47 InnoDB: Mutexes and rw_locks use GCC atomic builtins 120623 23:12:47 InnoDB: Compressed tables use zlib 1.2.3 120623 23:12:47 InnoDB: Initializing buffer pool, size = 128.0M 120623 23:12:47 InnoDB: Completed initialization of buffer pool 120623 23:12:47 InnoDB: highest supported file format is Barracuda. 120623 23:12:47 InnoDB: Waiting for the background threads to start 120623 23:12:48 InnoDB: 1.1.5 started; log sequence number 1595675 120623 23:12:48 [ERROR] /Applications/MAMP/Library/bin/mysqld: unknown option '--skip-locking' 120623 23:12:48 [ERROR] Aborting 120623 23:12:48 InnoDB: Starting shutdown... 120623 23:12:49 InnoDB: Shutdown completed; log sequence number 1595675 120623 23:12:49 [Note] /Applications/MAMP/Library/bin/mysqld: Shutdown complete i have deleted the mysql.pid file located at /application/mamp/tmp/mysql/mysql.pid and i still get the error above. I can't find where MAMP has set --skip-locking set, my.cnf doesnt have it anywhere. Activity monitor gives me a mysqld process running by me, and everytime i KILL the process both via Activity Monitor and via kill =9 pid it starts right back up.. Sampling the process points back to the MAMP mysqld.. wtf?! About to throw MAMP out the window and boot up a VM of CentOS =)

  Read the article

• SSD for swap on Ubuntu server

  - by grs

  Currently I am reading SSD reviews and I wonder how much exactly I will benefit if I move the 24 GB swap from 7200rpm HDD to SSD. Does anyone implemented swap space on SSD? Is this generally good idea? On a side note: I read that ext4 has much better performance if the journal is on SSD. Anyone with such a setup? Thanks! Edit: Here I will answer the questions posted: Occasionally, relatively rare I am hitting the swap. I know what the swap is for and that is better to get more RAM. When the server begins to swap its performance degrades (not a surprise). The idea is if I have few memory hungry processes running, to improve the overall system performance at that time, using SSD for swap, instead of slower rotational media. At the end - I want to be able to login faster and check the server state during swapping, instead of waiting on the login prompt. And of what I see SSD is cheaper per GB than RAM. Would I have better server performance during swapping (as rare it is) using SSD compared to HDD? Where 10k or 15k rpm HDDs would rate in this scenario? Thank you all for your quick and prompt answers!

  Read the article

• Apache2: Limit simultaneous requests & throttle bandwidth per IP/client?

  - by xentek

  I want to limit simultaneous requests & throttle bandwidth per IP/Client on a single apache vhost. In other words, I want to ensure that this site, which hosts large media files, doesn't get hammered by someone trying to download everything all at once (just happened the other night). I'd like to limit the outgoing transfer speed overall for this site, as well as limit the number of connections a single IP can make to the server to a sane default (i.e. within normal browser limits for multiple requests so page loads aren't effected too much). Bonus points if I can actually scope it to file types (i.e. leave web files alone, but apply these rules to just the media files). We're running Ubuntu 9.04 on all the servers, and have two apache/php servers being load balanced via Round Robin by a squid proxy server. MySQL is running on its own box as well. We've got plenty of bandwidth to give them, so I don't really want overall caps, but just want to throttle the amount of memory/CPU it takes to serve this site. There other sites on these servers that we don't want to apply these rules too, just want to keep this one from hogging all the resources. Let me know if you need more info! Thanks in advance for your suggestions!

  Read the article

• Is there an application to log component temperatures to file?

  - by MrVimes

  I purchased a computer a month or two ago (core i7, 24gb ram, geforce gtx 590, windows 7 ultimate). Within the last week it began to bluescreen regularly. I tried lots of things (check hds, check memory, reinstall windows etc..) but it still bluescreened. At the time my temps were as follows... CPU - aprox 40/50c. GPU - arpox 60 idle, aprox 90 during heavy use. HDDs - aprox 55c after the PC had been on a while. I thought the 55c was ok, but I have since realized it was probably too high and may have been the direct cause of the bluescreening. I've installed a spare fan I had in the front of the PC blowing air in, (so there's airflow from front to back) Since then, obviously, all my temps are down. Especially the HDDs - three of them reach 30c and one has been up to 47c (it is some distance away from the airflow, in one of the 5.25inch drive bays) I haven't had the PC on for as long as it would normally take to bluescreen yet, but If it does I want to know what all the temps were right before the bluescreen. I have tried Everest but it only shows me realtime temps or gives me the ability to create one-off reports. I want something that can record all the temps to a file at 30 seconds intervals. If the computer bluescreens I can load it up again and check the last entry in the file. Side question: Am I right in thinking 55c was far too hot for a HDD? (It might have got higher than that before the bluescreens.. I don't know) Another side question: Is 47c too high? This is actually why I am asking the main question - I am concerned that this one drive that isn't getting the benefit of the extra fan may still cause the computer to bluescreen.

  Read the article

• Some Apps don't start on Windows 8 Release Preview

  - by Exa

  I recently installed the Release Preview of Windows 8 in a virtual machine. Some apps do not work. When I open them (by clicking on their tile in the start screen) I see a splash screen and nothing else happens. Sometimes the app crashes after 30 seconds, sometimes it just keeps on loading. A good example is the "Map"-App from Windows 8 or the app "Cookbook" by Bewise. I installed Cookbook and when I had a look at the task manager I saw that it was the 32bit version running, but I have an x64 Windows 8... Could this be a problem? Shouldn't the Windows Store download the correct version? This is the setup of my virtual machine: Windows 8 Release Preview x64 Oracle VirtualBox 4 of 8 cores from host system 8 of 16 GB RAM from the host system 256 MB graphics memory guest additions installed resolution 1920 x 1080 Do you need further information? Unfortunately there is no error message... I just see the start screen of the app with its logo and it keeps loading, but nothing happens. Other Apps (like Mail, Video, Social, etc.) work fine.

  Read the article

• Server 2008 RAID 5 Write Speeds

  - by Solipsism

  I recently configured a RAID 5 partition in Server 2008 with 4 RAID 5 disks. These disks are connected through a SATA expansion card that uses PCIe. This morning, I checked and they had finally finished synchronizing, and so I tried to do some speed tests. Copying off the disks started pretty much fine - speeds began at 125MB/s, then trailed down to about 70MB/s, which I found odd but not worrying. Writing TO the disks however is a completely different story. I attempted to copy some of my VM host ISOs onto the disks (~2-4 GB apiece) and this resulted in speeds of approximately 10MB/s. I tried copying both from a local disk (connected directly to the motherboard) and from another server ththe gigabit network and results were the same. I checked the performance monitor while transferring the files and the only thing that stuck out was that my memory hard faults shot up to 6,000 per minute (spiking around 200/s) by explorer.exe. The system is running 2GB of DDR667 ECC RAM and a quad-core 2.3GHz opteron. Is there anything I can do to fix this performance issue (buy more RAM? move the drives to a faster box?, etc) or am I just screwed so long as I stick to windows.

  Read the article

• How long will a "safely stored" Solid-State-Drive (SSD) keep its data? (e.g. bank safety-deposit box)

  - by user31575

  Here's my usecase: once-and-only-once copy off photos/videos to an internal SATA Solid State Drive (SSD) put this drive in a well-ventilated, air-conditioned bank "safety deposit box" for safe keeping The question: How long can I safely store a solid-state-drive in such an environment? i.e. 0% bitrot, 100% success when "plugged in" Are some SSD drives more reliable than other for this usecase? (e.g. smaller size vs larger size, SLC vs MLC, different brands, etc) More fodder: I have read that solid state memory cards (e..g compactflash, or sd cards) have much longer durability than other media (DVD's, CD's, hard drives) for this usecase (guaranteed against bitrot/other dysfunction on the order of ~ a decades vs a year ). I don't know if this applies to "SSD hard drives". Copying to one 500Gb ssd vs 8 64gb flash drives is easier SSD SATA hard drives have no moving parts, but they have more "visible electronics" than a compact flash card. I don't know if this "visible electronics" can fail, i.e. in contr I know many will point to carbonite, other cloud backup stuff, but I like the simplicity of having physical copies and wanted to understand the risks/implications thanks,

  Read the article

• Replacing the LCD panel in a netbook (Asus Eee PC 1005)

  - by neilfein

  Yesterday, I was cleaning up and dropped my Asus Eee 1005PE. The screen is cracked inside (i.e., cracks are visible only when on), and no longer works properly. I booted up with another monitor attached, and the computer itself is fine, but needs a new screen. Best Buy wants at least $250 to repair it (that includes their $150 fee to breathe in the same room as the unit), and Asus was of no help at all. (They're incredibly cagey and won't provide any money numbers at all, not even the cost of the part.) If replacing the LCD is no more trouble than replacing memory or a hard drive, I can do that. It's within my means to buy the part (18G241010402, a TFT LCD), but I'd like to know more about the procedure involved. My question: How does one replace the screen in this unit? Do I simply open the case and swap out the unit, or do I need to disassemble anything else to get to the screen? I don't want to order the part and then end up in a situation like this. Is the case screwed shut, or is it like an iPod where they glue things closed? I know enough about my abilities with a soldering gun to not attempt to solder tiny wires, would any of that be involved?

  Read the article

• Measuring performance indicators on a cluster

  - by Aditya Singh

  My architecture is based on Amazon. A ELB load balancer balances POST requests among m1.large instances. Every instance has a nginx server on port 80 which distributes the requests to 4 python-tornado servers on backend which handle the request. These tornado servers are taking about 5 - 10ms to respond to one request but this is the internal compute time of every request. I want to put this thing on test and i want to measure the response time from ELB to upstream and back and how does it vary when the QPS throughput is increased and plot a graph of Time vs. QPS vs. Latency and other factors like CPU and Memory. Is there a software to do that or should i log everything somewhere with latency checks and then analyze the whole log to get the stuff out. I would also need to write a self-monitor which keeps checking the whole response time. Is it possible to do it with a script from within the server. If so, will it be accurate ?

  Read the article

• bond0:0 + define virtual IP

  - by yael

  hi all in my linux server I have the follwoing: Linux Version - RedHat-Linux- 5.3.0.0 (this linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it posible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

  Read the article

• bond0:0 + define virtual IP

  - by yael

  hi all in my linux server I have the follwoing: Linux Version - RedHat-Linux- 5.3.0.0 (this linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it posible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

  Read the article

• How to kill ostensibly immortal process?

  - by DeeDee

  I had some huge file transfers operating on an NFS mount. The server on which the mount point resided was carelessly rebooted, and now the server from which these large transfers were initiated seems to be bogged down by them. If I run top, I see the following: The first thing I tried was to run kill with each the -1 -2 -9 and -15 flags, and each of the process ids shown above in turn. This allowed me to proceed, but didn't kill the processes. The next thing I attempted was to reboot the server, but neither reboot nor shutdown -r now worked. When I ran shutdown -r now the standard broadcast message was sent out, but the sever did not reboot. I confirmed this by looking at the server uptime, which was 25 days. So now I'm a little stuck. I'm running these commands as root. EDIT: Here's another interesting tidbit: In top, I don't see that any other processes are using more than a fraction of a percent of memory or more than 5% of CPU. EDIT 2: output of /var/log/messages

  Read the article

< Previous Page | 417 418 419 420 421 422 423 424 425 426 427 428  | Next Page >