Search Results

Search found 34056 results on 1363 pages for 'mod access'.

Page 421/1363 | < Previous Page | 417 418 419 420 421 422 423 424 425 426 427 428  | Next Page >

  • Ubuntu Laptop as a wireless hotspot on bridge mode

    - by nixnotwin
    I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

    Read the article

  • Sharepoint Central Administration stuck / high CPU usage

    - by johnnyb10
    I'm using WSS 3 and I recently added a new web application to my SharePoint Server. After adding it, I wasn't able to open the Central Administration site. I also noticed that there was a w3wp.exe error (Event ID 1000) in the Event Viewer. The situation now is that the w3wp.exe process is hovering around 50% CPU usage continuously. I installed a program called IIS Peek, and it shows continuous GET requests on the Central Administration site; this happens even if I stop the Central Administration site in IIS. The IP addresses identified in the GET request is my workstation, which is what I used to attempt to access Central Administration after I created the new web application. Can someone explain what's going on and how I might fix it? It seems as if my computer tried to access Central Administration and then it hung, but the page requests that were happening at the time are somehow continuing over and over again. So my two problems are the inability to access Central Administration, and the CPU Usage of w3wp.exe, which I'm assuming are two symptoms of the same problem. I'd like to know if there's anything I can do besides restarting IIS, because we have clients accessing other sites on this server. Thanks.

    Read the article

  • SQL Server Reporting Services - website blank, builder works

    - by Keith
    We have a few reports in SQL Server Reporting Services. For some reason when we run the report from the website, it doesn't return any data. When I run the same report from the Report Builder, it returns data. I looked in the logs and the only errors I could find is: ReportingServicesService!library!8!6/15/2012-08:12:33:: i INFO: Current DB Version Unknown, Instance Version C.0.8.54. ReportingServicesService!library!8!6/15/2012-08:12:33:: e ERROR: Throwing Microsoft.ReportingServices.Diagnostics.Utilities.InvalidReportServerDatabaseException: The version of the report server database is either in a format that is not valid, or it cannot be read. The found version is 'Unknown'. The expected version is 'C.0.8.54'. To continue, update the version of the report server database and verify access rights., ;Info: Microsoft.ReportingServices.Diagnostics.Utilities.InvalidReportServerDatabaseException: The version of the report server database is either in a format that is not valid, or it cannot be read. The found version is 'Unknown'. The expected version is 'C.0.8.54'. To continue, update the version of the report server database and verify access rights. ReportingServicesService!library!8!6/15/2012-08:12:33:: e ERROR: Exception caught while starting service. Error: Microsoft.ReportingServices.Diagnostics.Utilities.InvalidReportServerDatabaseException: The version of the report server database is either in a format that is not valid, or it cannot be read. The found version is 'Unknown'. The expected version is 'C.0.8.54'. To continue, update the version of the report server database and verify access rights. I'm not really sure why it would be a different version. It's all SQL Server 2008 R2 and I haven't made any changes to it since it's been running.

    Read the article

  • Is Gmail Being Blocked by my ISP (wait till you read this)?

    - by James
    This is the strangest thing I have ever encountered. I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). So okay, maybe my ISP is blocking these for some reason or maybe my firewall is, or maybe there is something wrong with my connectivity, right? NO. On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail ages starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping a complete reinstall would solve the issue, but no luck. So can anyone for the life of them figure out why this could be? And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cabel from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before gmail was perfectly accessible in this computer. I can't remember anything special that happened on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter

    Read the article

  • VirtualBox VM running web server not accessible via external IP

    - by mwigdahl
    I have a Windows 7 machine running VirtualBox with an Ubuntu guest. The guest has a Bitnami LAMP stack installed. I have the guest configured for Bridged networking, and I can access the guest web server just fine from other machines on my LAN using the guest's IP. I'm trying to configure port forwarding so that I can access the web server from outside my LAN. (The router is a 2WIRE model as I'm on ATT's UVerse). I've set up port forwarding for ports 80 and 443 to the guest's IP in a similar manner to how I had them set up for my previous, physical web server, which worked just fine. However, I cannot seem to access the new, virtual web server using my external IP on the forwarded port. I suspected Windows Firewall issues on the host, but disabling it didn't solve the issue. Anyone have advice on what I should try next? EDIT: I've now attempted disabling the firewall on the guest with sudo ufw disable -- that doesn't seem to help either. However, after checking the router's port forwarding in more detail I may see the problem. My VM is named "linux" and in the router's configuration pages it shows up inconsistently. Sometimes it reports with a valid LAN IP and other times it doesn't show up with any IP. Even when it shows the correct IP the router indicates that it is disconnected. Could this be an indication that the 2WIRE router doesn't play well with VirtualBox's bridged networking mode?

    Read the article

  • SFTP, Chroot problems on Redhat

    - by Curtis_w
    I'm having problems setting up sftp with a ChrootDirectory. I've done an equivalent setup on other distros, but for some reason I cannot get it to work on a Redhat AMI. The changes to my sshd_config file are: Subsystem sftp internal-sftp Match Group ftponly PasswordAuthentication yes X11Forwarding no ChrootDirectory %h ForceCommand internal-sftp AllowTcpForwarding no I have the concerned usere's homes at /home/user, owned by root. After connecting with a user in the ftponly group, I'm dropped into / without permissions for anything, and am unable to do anything. sftp bob@localhost Connecting to localhost... bob@localhost's password: sftp> pwd Remote working directory: / I can connect normally with users not in the ftponly group. openssh version 5.3 I've experimented with different permissions, as well as having users own their own home directory (gives a Write failed: Broken pipe error), and so far, nothing has seemed to work. I'm sure it's a permissions error, or something equally as trivial, but at this point my eyes are beginning to glaze over, and any help would be greatly appreciated. EDIT: James and Madhatter, thanks for clarifying. I was confused by chroot dropping me in /... just didn't think through it properly. I've added the appropriate directories and permissions to get read access. One other key part was enabling write access to chrooted homes: setsebool -P ssh_chroot_rw_homedirs on in order to get write access. I think I'm all set now. Thanks for the help.

    Read the article

  • Active Directory + IIS + SQL + ASP.NET

    - by Amira Elsayed Ismail
    I have sent the following question to stackoverflow website I have installed Windows server 2008 r2 on a virtual machine, Can I install Active directory with domain controller + IIS + SQL server on the same machine? I want to make web application and this web application will authenticate users from Active Directory, the web application should be published on the server IIS and the users should access it remotely from their home using domain name of my machine, Someone tell me that its very wrong to have IIS and Active directory on the same machine I got the following Answer You can't use ActiveDirectory over the internet. At least not without something like a VPN as a middle man. Their home computers will not be joined to the domain, so there is no pass-through authentication. Yes, it's a bad idea to put AD on the web server. Why is too complex to get into in an answer here. Suffice it to say that even if you did do this, it's probably would not work the way you are thinking it should. It's not impossible to do this. For instance, many of the Microsoft "Small Businesss" products put IIS, AD, and SQL Server on the same server. But, you kind of have to know what you're doing to configure it securely. Then I add the following comment Thanks for ur reply.so what you think about the best way to do this as I didn't do anything like that before should I install active directory on a machine and IIS on another machine ? and what about SQL should I add it to the same server of active directory ? I didn't mentioned also that it will be Microsoft dynamics server that will access some information about work and i have to read data from axapta also ? also what is VPN and how can I use it to let users access my web application anywhere ? Sorry for my long questions and thanks in advance so please if anyone can help I will be thankful

    Read the article

  • Permissions nightmare - tried all I know

    - by Ben
    Working on a new client's dev site, which is a wordpress install on a Plesk box. I have SSH root access, and FTP access through a separate account. What I've done so far Initially I couldn't make any changes to any files at all. The permissions on all the template files looked a little screwy (644), so I figured change them to allow group, and add myself to the group: CHMOD Recursive on the theme folder to set everything to 664 Quickly realised I'd broken it, set the folders to 755, kept files as 664 Ownership on all files is a mixture of root:root and 500:500 (there is no user nor group with the ID of 500 on the server). Added myself to the group 'root' so I could modify the files too The Problem This worked OK, in terms of being able to edit the existing files, so I began working. However, I can't upload to the directory, even having run CHOWN -R root:root templatefolder/ and being in the root group. I feel like I must be missing something obvious, and it's doing my head in. Questions: Files in the install owned by 500 with group 500 - I've looked in /etc/group and /etc/passwd and there is no user nor group with this ID. Is that left over from another developer's setup or the previous server (they moved recently)? Is being in the 'root' group enough, or do I need to own the theme folder as 'myftpuser' in order to upload and create new files? Like I say, I have edit access, so I got myself this far. I'm now questioning what to do next!

    Read the article

  • Apache22 on FreeBSD - Starts, does not respond to requests

    - by NuclearDog
    Hey folks! I'm running Apache 2.2.17 with the peruser MPM on FreeBSD 8.2-RC1 on Amazon's EC2 (so it's XEN). It was installed from ports. My problem is that, although Apache is running, listening for, and accepting connections, it doesn't actually respond to any or show them in the log at all. If I telnet to the port it's listening on and type out an HTTP request: GET / HTTP/1.1 Host: asdfasdf And hit enter a couple of times, it just sits there... Nothing. No response requesting with a browser either. There doesn't appear to be anything helpful in the error log: [Sun Jan 09 16:56:24 2011] [warn] Init: Session Cache is not configured [hint: SSLSessionCache] [Sun Jan 09 16:56:25 2011] [notice] Digest: generating secret for digest authentication ... [Sun Jan 09 16:56:25 2011] [notice] Digest: done [Sun Jan 09 16:56:25 2011] [notice] Apache/2.2.17 (FreeBSD) mod_ssl/2.2.17 The access log stays empty: root:/var/log# wc httpd-access.log 0 0 0 httpd-access.log root:/var/log# I've tried with accf_http and accf_data both enabled and disabled, and with both the stock configuration and my customized config. I also tried uninstalling apache22-peruser-mpm and just installing straight apache22... Still no luck. I tried removing all of the LoadModule lines from httpd.conf and just re-enabled the ones that were necessary to parse the config. Ended up with only the following loaded: root:/usr/local/etc/apache22# /usr/local/sbin/apachectl -M Loaded Modules: core_module (static) mpm_peruser_module (static) http_module (static) so_module (static) authz_host_module (shared) log_config_module (shared) alias_module (shared) Syntax OK root:/usr/local/etc/apache22# Same results. Apache is definitely what's listening on port 80: root:/usr/local/etc/apache22# sockstat -4 | grep httpd root httpd 43789 3 tcp4 6 *:80 *:* root httpd 43789 4 tcp4 *:* *:* root:/usr/local/etc/apache22# And I know it's not a firewall issue as there is nothing running locally, and connecting from the local box to 127.0.0.1:80 results in the same issue. Does anyone have any idea what's going on? Why it would be doing this? I've exhausted all of my debugging expertise. :/ Thanks for any suggestions!

    Read the article

  • Scripting an 'empty' password in /etc/shadow

    - by paddy
    I've written a script to add CVS and SVN users on a Linux server (Slackware 14.0). This script creates the user if necessary, and either copies the user's SSH key from an existing shell account or generates a new SSH key. Just to be clear, the accounts are specifically for SVN or CVS. So the entry in /home/${username}/.ssh/authorized_keys begins with (using CVS as an example): command="/usr/bin/cvs server",no-port-forwarding,no-agent-forwarding,no-X11-forwarding,no-pty ssh-rsa ....etc...etc...etc... Actual shell access will never be allowed for these users - they are purely there to provide access to our source repositories via SSH. My problem is that when I add a new user, they get an empty password in /etc/shadow by default. It looks like: paddycvs:!:15679:0:99999:7::: If I leave the shadow file as is (with the !), SSH authentication fails. To enable SSH, I must first run passwd for the new user and enter something. I have two issues with doing that. First, it requires user input which I can't allow in this script. Second, it potentially allows the user to login at the physical terminal (if they have physical access, which they might, and know the secret password -- okay, so that's unlikely). The way I normally prevent users from logging in is to set their shell to /bin/false, but if I do that then SSH doesn't work either! Does anyone have a suggestion for scripting this? Should I simply use sed or something and replace the relevant line in the shadow file with a preset encrypted secret password string? Or is there a better way? Cheers =)

    Read the article

  • fail2ban regex working but no action being taken

    - by fpghost
    I have the following snippet of fail2ban configuration on Ubuntu 13.10 server: #jail.conf [apache-getphp] enabled = true port = http,https filter = apache-getphp action = iptables-multiport[name=apache-getphp, port="http,https", protocol=tcp] mail-whois[name=apache-getphp, dest=root] logpath = /srv/apache/log/access.log maxretry = 1 #filter.d/apache-getphp.conf [Definition] failregex = ^<HOST> - - (?:\[[^]]*\] )+\"(GET|POST) /(?i)(PMA|phptest|phpmyadmin|myadmin|mysql|mysqladmin|sqladmin|mypma|admin|xampp|mysqldb|mydb|db|pmadb|phpmyadmin1|phpmyadmin2|cgi-bin) ignoreregex = I know the regex is good, because if I run the test command on my access.log: fail2ban-regex /srv/apache/log/access.log /etc/fail2ban/filter.d/apache-getphp.conf I get a SUCCESS result with multiple hits, and in my log I see entries like 187.192.89.147 - - [13/Apr/2014:11:36:03 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 301 585 "-" "-" 187.192.89.147 - - [13/Apr/2014:11:36:03 +0100] "GET /phpMyAdmin/scripts/setup.php HTTP/1.1" 301 593 "-" "-" Secondly I know email is configured correctly, as each time I service fail2ban restart I get an email for each of the filters stopping/starting. However despite all this no action seems to be taken when one of these requests comes in. No email with whois, and no entries in iptables. What possibly could be preventing fail2ban from taking action? (everything looks in order in fail2ban-client -d and I can see the chains have loaded with iptables -L)

    Read the article

  • iptables port forward + nginx redirect problem

    - by easthero
    Here is my network browser = proxy(iptables port forward) = nginx server proxy: 192.168.10.204, forward 192.168.10.204:22080 to 192.168.10.10:80 nginx server: 192.168.10.10 nginx version:0.7.65 debian testing in nginx settings, I set: server_name _; server_name_in_redirect off; because my server has no domain now, access 192.168.10.10/index.html or 192.168.10.10/foobar is ok then access 192.168.10.204:22080/index.html is ok but access 192.168.10.204:22080/foobar, nginx 301 redirect to http://192.168.10.204/foobar how to fix? thanks telnet 192.168.10.204 22080 Trying 192.168.10.204... Connected to 192.168.10.204. Escape character is '^]'. GET /index.html HTTP/1.1 Host: 192.168.10.10 HTTP/1.1 200 OK Server: nginx/0.7.65 Date: Fri, 28 May 2010 10:07:29 GMT Content-Type: text/html Content-Length: 12 Last-Modified: Fri, 28 May 2010 07:25:12 GMT Connection: keep-alive Accept-Ranges: bytes hello world telnet 192.168.10.204 22080 Trying 192.168.10.204... Connected to 192.168.10.204. Escape character is '^]'. GET /test2 HTTP/1.1 Host: 192.168.10.10 HTTP/1.1 301 Moved Permanently Server: nginx/0.7.65 Date: Fri, 28 May 2010 10:04:20 GMT Content-Type: text/html Content-Length: 185 Location: http://192.168.10.10/test2/ Connection: keep-alive <html> <head><title>301 Moved Permanently</title></head> <body bgcolor="white"> <center><h1>301 Moved Permanently</h1></center> <hr><center>nginx/0.7.65</center> </body> </html>

    Read the article

  • Setting the default permissions for files uploaded via FTP to a directory

    - by Kerri
    Disclaimer: I'm just a web designer/coder, and server admin stuff is my weakest point of them all. So be easy on me (and very specific). I'm using a simple CMS (Unify) on a site, where part of the functionality is that the client can upload files to a specified directory (using FTP). The permissions for the upload directory are set to 755. But when files are uploaded through the interface, they are uploaded with permissions set to 640 (instead of 644), so site visitors cannot acces the files. When I emailed the CMS's support about this, they told me that it was a server setting, and I need to make sure that files uploaded through FTP are set to 644. Makes perfect sense, but I have no idea how to do this. Any help would be greatly appreciated. This site is a shared site hosted by Network Solutions (Unix), so my access options are limited. I can edit .htaccess files, and php.ini, but that's about all I have access to. It appears I can't even log on via shell. ETA: 11/11/2010 Thanks all. I was able to work around this problem by setting up the CMS's settings in a different way. I'd be interested in following up on Nick O'Niel's suggestions, because I think he's on the right track, but unfortunately I can't access the necessary files on this particular server. So, anyway, I'm leaving this open, since the original questions isn't exactly resolved. Unfortunately, I probably can't put a correct answer to the test, since the shared server in question has nearly all of its config files tightly locked down.

    Read the article

  • VLAN for WiFi traffic separation (new to VLANing)

    - by Philip
    I run a school network with switches in different departments. All is routed through to a central switch to access the servers. I would like to install WiFi access points in the different departments and have this routed through the firewall (an Untangle box that can captive-portal the traffic, to provide authentication) before it gets onto the LAN or to the Internet. I know that the ports that the APs connect to on the relevant switches need to be set to a different VLAN. My question is how do I configure these ports. Which are tagged? Which are untagged? I obviously don't want to interrupt normal network traffic. Am I correct in saying: The majority of the ports should be UNTAGGED VLAN 1? Those that have WiFi APs attached should be UNTAGGED VLAN 2 (only) The uplinks to the central switch should be TAGGED VLAN 1 and TAGGED VLAN 2 The central switch's incoming ports from the outlying switches should also be TAGGED VLAN 1 and TAGGED VLAN 2 There will be two links to the firewall (each on its own NIC), one UNTAGGED VLAN 1 (for normal internet access traffic) and one UNTAGGED VLAN 2 (for captive portal authentication). This does mean that all wireless traffic will be routed over a single NIC which will also up the workload for the firewall. At this stage, I'm not concerned about that load.

    Read the article

  • iMac 20inch (Mid 2007) SL DVD Boot Prohibitory Sign

    - by Caitlann Lloyd
    iMac 20inch (Mid 2007 Build) with Ubuntu 12.0.4 How I got in this situation I had a perfectly healthy Intel iMac running Snow Leopard several months ago. Then I got the dreaded spinning gear and several kernel panics. After getting a little frustrated (failing to find a solution online), I found an old macbook installation disk and used it to access Disk Utility. From here, I erased my entire hard drive leaving me with no OS. I then created a Ubuntu DVD and installed Ubuntu onto the system. Now, on Ubuntu, I wine installed Transmac and burned a Single layer copy (with languages, etc. removed to save space) of Snow Leopard onto a 4.7GB DVD. I tried to boot from it and was met with first the grey apple screen and a spinning cog before the grey apple shortly turned into the infamous prohibitory sign. Note: I met this problem previously when using Disk Utility to create a bootable USB of Snow Leopard, hence I severely doubt it has anything to do with the DVD created. Resources at my disposal 1 x iMac running Ubuntu 6 x 4.7GB DVDs 1 x USB Stick 12GB 1 x Windows 7 Laptop Resources I do not have Firewire cables Access to a prebuilt retail disk (Misplaced) Access to another Mac Apple Warranty I would be hugely grateful if someone was able to tell me how to install Snow Leopard again.

    Read the article

  • iptables captive portal remove user

    - by Burgos
    I followed this guide: http://aryo.info/labs/captive-portal-using-php-and-iptables.html I am implementing captive portal using iptables. I've setup web server and iptables on linux router, and everything is working as it should. I can allow user to access internet with sudo iptables -I internet -t mangle -m mac --mac-source USER_MAC_ADDRESS -j RETURN and I can remove access with sudo iptables -D internet -t mangle -m mac --mac-source USER_MAC_ADDRESS -j RETURN However, on removal, user can still open last viewed page as many times he wants (if he restart his Ethernet adapter, future connections will be closed). On blog page I found a script /usr/sbin/conntrack -L \ |grep $1 \ |grep ESTAB \ |grep 'dport=80' \ |awk \ "{ system(\"conntrack -D --orig-src $1 --orig-dst \" \ substr(\$6,5) \" -p tcp --orig-port-src \" substr(\$7,7) \" \ --orig-port-dst 80\"); }" Which should remove their "redirection" connection track, as it is written, but when I execute that script, nothing happens - user still have access to that page. When I execute /usr/sbin/conntrack -L | grep USER_IP after executing script I am having nothing returned, so my questions: Is there anything else that can help me clean these track? Obviously - I can't reset nor mine, nor users network adapter.

    Read the article

  • Problem routing between directly connected Subnets w/ ASA-5510

    - by Zephyr Pellerin
    This is an issue I've been struggling with for quite some time, with a seemingly simple answer (Aren't all IT problems?). And that is the problem of passing traffic between two directly connected subnets with an ASA While I'm aware that best practice is to have Internet - Firewall - Router, in many cases this isn't possible. For example, In have an ASA with two interfaces, named OutsideNetwork (10.19.200.3/24) and InternalNetwork (10.19.4.254/24). You'd expect Outside to be able to get to, say, 10.19.4.1, or at LEAST 10.19.4.254, but pinging the interface gives only bad news. Result of the command: "ping OutsideNetwork 10.19.4.254" Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.19.4.254, timeout is 2 seconds: ????? Success rate is 0 percent (0/5) Naturally, you'd assume that you could add a static route, to no avail. [ERROR] route Outsidenetwork 10.19.4.0 255.255.255.0 10.19.4.254 1 Cannot add route, connected route exists At this point, you might gander if its a NAT or Access list problem. access-list Outsidenetwork_access_in extended permit ip any any access-list Internalnetwork_access_in extended permit ip any any There is no dynamic nat (or static nat for that matter), and Unnatted traffic is permitted. When I try pinging the above address (10.19.4.254 from Outsidenetwork), I get this error message from level 0 logging (debugging). Routing failed to locate next hop for icmp from NP Identity Ifc:10.19.200.3/0 to Outsidenetwork:10.19.4.1/0 This led me to set same-security traffic permit, and assigned the same, lesser and greater security numbers between the two interfaces. Am I overlooking something obvious? Is there a command to set static routes that are classified higher than connected routes?

    Read the article

  • How to clone MySQL DB? Errors with CREATE VIEW/SHOW VIEW privileges

    - by user38071
    Running MySQL 5.0.32 on Debian 4.0 (Etch). I'm trying to clone a WordPress MySQL database completely (structure and data) on the same server. I tried doing a dump to a .sql file and an import into a new empty database from the command line, but the import fails with errors saying the user does not have the "SHOW VIEW" or "CREATE VIEW" privilege. Trying it with PHPMyAdmin doesn't work either. I also tried doing this with the MySQL root user (not named "root" though) and it shows an "Access Denied" error. I'm terribly confused as to where the problem is. Any pointers on cloning a MySQL DB and granting all privileges to a user account would be great (specifically for MySQL 5.0.32). The SHOW GRANTS command for the existing user works (the one who has privileges over the source database). It shows that the user has all privileges granted. I created a new user and database. Here's what I see with the grant commands. $ mysql -A -umyrootaccount --password=myrootaccountpassword mysql> grant all privileges on `newtarget_db`.* to 'newtestuser'@'localhost'; ERROR 1044 (42000): Access denied for user 'myrootaccount'@'localhost' to database 'newtarget_db' mysql> grant all privileges on `newtarget_db`.* to 'existingsourcedbuser'@'localhost'; ERROR 1044 (42000): Access denied for user 'myrootaccount'@'localhost' to database 'newtarget_db'

    Read the article

  • OpenLDAP ACLs are not working

    - by Dr I
    First things first, I'm currently working with an OpenLDAP: slapd 2.4.36 on a Fedora release 19 (Schrödinger’s Cat). I've just install the openldap with yum and my configuration is the following one: ##### OpenLDAP Default configuration ##### # ##### OpenLDAP CORE CONFIGURATION ##### include /etc/openldap/schema/core.schema include /etc/openldap/schema/cosine.schema include /etc/openldap/schema/inetorgperson.schema include /etc/openldap/schema/nis.schema pidfile /var/lib/ldap/slapd.pid loglevel trace ##### Default Schema ##### database mdb directory /var/lib/ldap/ maxsize 1073741824 suffix "dc=domain,dc=tld" rootdn "cn=root,dc=domain,dc=tld" rootpw {SSHA}SECRETP@SSWORD ##### Default ACL ##### access to attrs=userpassword by self write by group.exact="cn=administrators,ou=builtin,ou=groups,dc=domain,dc=tld" write by anonymous auth by * none I launch my OpenLDAP service using: /usr/sbin/slapd -u ldap -h ldapi:/// ldap:/// -f /etc/openldap/slapd.conf As you can see it's a pretty simple ACL which aim to allow access to the userPassword attribute to a specific group read only, then to the owner read and write to anonymous requiring auth and refuse the access to everyone else. The problem is: Even using a valid user with correct password my ldapsearch ends with zero informations retrieved from the directory, plus I've got a strange response on the result line. # search result search: 2 result: 32 No such object # numResponses: 1 here is the ldapsearch request: ldapsearch -H ldap.domain.tld -W -b dc=domain,dc=tld -s sub -D cn=user,ou=service,ou=employees,ou=users,dc=domain,dc=tld I did not specify any filter as I want to check that ldapsearch is correctly printing only allowed attribute.

    Read the article

  • Filesharing mac 10.6 with windows vista

    - by adam
    Ive followed all the tutorials on the net to no avail. I can see my vista pc in finder on the mac but when I click on it tries to connect but fails. The same is true from vista, it can see the mac but i cant connect. Wont even offer a login box. So I tried to troubleshoot by using a 3rd computer with xp. It joined the network and can access both the mac and vista on the same workgroup. Mac sees it and it shows under finder but i cant access it by clicking on the icon i have to access by using the ip of the xp machine...strange. Ive turned off all my firewalls. The fact that xp can connnet to the others and vice versa boggles my mind why vista and mac cant connect directly. Oh and pings indicates the same. I.e. xp has no problem but mac to vista and vice versa fails. Can anyone help.

    Read the article

  • Mavericks permission issues with Windows Server deduplicated shares

    - by dmohlmaster
    We have a number of 10.9-10.9.3 - Mavericks - machines installed throughout our facility. Much of the user content is pulled from shares stored on our Windows Server 2012 fileservers with deduplication enabled. I have found that files newly written or unoptimized are able to be accessed without issue - read, written, modified, etc. Once the file gets optomized/deduplicated and Windows adds the P & L attributes - sparse and symlink - the Macs running Mavericks begin to have access issues. Once the files get deduplicated, users begin receiving read access errors when copying files (see error1 below). This happens when copying to folders within the current folder tree or copying somewhere to the local system. If you 'stop' the copy operation and retry a few more times, it may eventually work for the specific instance but fail again later. I am however, able to copy these files without issue via the terminal. Other systems running 10.7 do not experience the same issues and are able to access file server resources without issue. Many of the systems having issues are newer and thus not able to be downgraded to 10.8 or 10.7. I have tried finder replacements such as Pathfinder but the results are the same. I know this is at least similar to the issues many Mac users are already experiencing and posting about but I haven't seen it directly linked to deduplication and the attributes written by Windows server. Has anyone seen this issue? Have any solutions been found? Error 1: When copying files after the PL attributes have been set by deduplication. "One or more items can't be copied to "Foler" because you don't have permissions to read them. ******************************************' Via the system.log, I am also seeing the following error when accessing these deduplicated file shares. The reparse point tag listed below is "IO_REPARSE_TAG_DEDUP" Reported error: "smbfs_nget: filename.ext - unknown reparse point tag 0x80000013"

    Read the article

  • Running phpmyadmin xampp Ubuntu 12.10

    - by Luigi Tiburzi
    I know it is a common problem and there are many solutions on the web but I'm trying everything and anything is working, I can't have phpmyadmin running on my machine. I installed XAMPP through: sudo tar xvfz ./Downloads/xampp-linux-1.8.1.tar.gz -C /opt then I did the chmod trick supposed to make an end to access issues and I change the default location to my php projects from /var/www to Dropbox/php. Then I started XAMPP in the usual way: sudo /opt/lampp/lampp start When I tried to run one of my php projects the output on the web is fine but if for example I try to write localhost on my browser I get: It works and not the usual XAMPP interface and most of all when I try to access localhost/phpmyadmin I get the login page, insert username (root) and password and I get: You don't have permission to access /phpmyadmin/index.php on this server. Apache/2.2.22 (Ubuntu) Server at localhost Port 80 I tried the Required all granted trick and some others but nothing is working. I even tried to uninstall phpmyadmin and reinstall it but this is not working too. I don't know hot to proceed. Thanks for your help.

    Read the article

  • debugging connection to mysql from python script using MySQLdb

    - by timpone
    I am a python newbie and have a python 2.5 script that is using MySQLdb to connect on OS X 10.5.8. I haven't been able to succesfully connect to the database of interest with this. However, I am able to connect using php's mysqli and also via the mysql cli interface. I get the error: File "build/bdist.macosx-10.5-i386/egg/MySQLdb/connections.py", line 188, in __init__ _mysql_exceptions.OperationalError: (1045, "Access denied for user 'arc_development'@'localhost' (using password: YES)") On my linux box which has the same mysql perms, the script works fine logging in. On my OS X laptop, I am able to create a database named test_python which bypasses mysql authentication scheme. This makes me think that issues like 32bit / 64bit incompatabilities aren't occuring. If I turn on the query log, I get access denied: 100610 20:56:55 4 Connect Access denied for user 'arc_development'@'localhost' (using password: YES) I'm a little bit at a loss to what to do next. Is there any way I can specify in the general log or binary log to get the actual password set on the connection string? How about writing out from connections.py file the value (although not sure how I'd do that)? thanks

    Read the article

  • Windows 2008 server smart card security module problem

    - by chris13work
    Hi, I've got a smart card reader and a server application using it as a security module. If I run it under DOS prompt, everything is fine. The server is running and clients can connect to it. I tried to install the server as window service and start it. The server starts but always gives back authentication error because it cannot call the smart card to do encryption. Then I tried to start it with task scheduler and set the trigger factor as "on startup". The server starts also but still cannot access the smart card reader. Then I tried remote desktop to the machine and run the server application under DOS prompt. Same error is returned. The situation is that the smart card reader only works under active console desktop environment. In the server application, WINSCARD API is used to access the smart card reader. Any suggestion so that we can access the smart card reader in running services? OS: Windows Server 2008 Smart Card Driver: Windows USB smart card Reader Smart Card API: WINSCARD

    Read the article

  • Windows 2008 server smart card security module problem

    - by chris13work
    Hi, I've got a smart card reader and a server application using it as a security module. If I run it under DOS prompt, everything is fine. The server is running and clients can connect to it. I tried to install the server as window service and start it. The server starts but always gives back authentication error because it cannot call the smart card to do encryption. Then I tried to start it with task scheduler and set the trigger factor as "on startup". The server starts also but still cannot access the smart card reader. Then I tried remote desktop to the machine and run the server application under DOS prompt. Same error is returned. The situation is that the smart card reader only works under active console desktop environment. In the server application, WINSCARD API is used to access the smart card reader. Any suggestion so that we can access the smart card reader in running services? OS: Windows Server 2008 Smart Card Driver: Windows USB smart card Reader Smart Card API: WINSCARD

    Read the article

< Previous Page | 417 418 419 420 421 422 423 424 425 426 427 428  | Next Page >