Search Results

Search found 12019 results on 481 pages for 'stop execution'.

Page 426/481 | < Previous Page | 422 423 424 425 426 427 428 429 430 431 432 433  | Next Page >

• NTPD issue - syncs then slowly loses ground

  - by ethrbunny

  RHEL 5 workstation. Has been running smoothly for years. I did a 'pup' recently and followed with a nice, cleansing reboot. Afterwards the system had some startup issues: namely MySQL refused to start. It just went "...." for 5-10 minutes before I did another boot and skipped that step (using 'interactive'). This was the only service that didn't wan't to start normally. So now that the system is booted I've found that it doesn't want to stay in sync with the NTP master and after 48 hours is refusing any SSH other than root. NTPD: this service starts normally and gets a lock on 4 servers. Almost immediately it starts to lose ground and now (after 3 days) is almost 40 hours behind. If I stop/start the service it gets the lock, resets the system clock and starts losing ground again. The 'hwclock' is set properly and maintains its time. Login: when I (re)start the ntp server I am able to login normally. I assume this problem is due to losing sync with LDAP. This appears to be verified by LDAP errors in /var/log/messages. Suggestions on where to look? ADDENDA: Tried deleting the 'drift' file. After a bit it gets recreated with 0.000. from /var/log/messages: Jan 17 06:54:01 aeolus ntpdate[5084]: step time server 129.95.96.10 offset 30.139216 sec Jan 17 06:54:01 aeolus ntpd[5086]: ntpd [email protected] Tue Oct 25 12:54:17 UTC 2011 (1) Jan 17 06:54:01 aeolus ntpd[5087]: precision = 1.000 usec Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface wildcard, 0.0.0.0#123 Disabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface wildcard, ::#123 Disabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface lo, ::1#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface eth0, fe80::213:72ff:fe20:4080#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface lo, 127.0.0.1#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface eth0, 10.127.24.81#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: kernel time sync status 0040 Jan 17 06:54:02 aeolus ntpd[5087]: frequency initialized 0.000 PPM from /var/lib/ntp/drift Jan 17 06:54:02 aeolus ntpd[5087]: system event 'event_restart' (0x01) status 'sync_alarm, sync_unspec, 1 event, event_unspec' (0xc010) You can see the 30 second offset. This was after about one minute of operation.

  Read the article

• Is Apache 2.2.22 able to sustain 1.000 simultaneous connected clients?

  - by Fnux

  For an article in a news paper, I'm benchmarking 5 different web servers (Apache2, Cherokee, Lighttpd, Monkey and Nginx). The tests made consist of measuring the execution times as well as different parameters such as the number of request served per second, the amount of RAM, the CPU used, during a growing load of simultaneous clients (from 1 to 1.000 with a step of 10) each client sending 1.000.000 requets of a small fixed file, then of a medium fixed file, then a small dynamic content (hello.php) and finally a complex dynamic content (the computation of the reimbursment of a loan). All the web servers are able to sustain such a load (up to 1.000 clients) but Apache2 which always stops to respond when the test reach 450 to 500 simultaneous clients. My configuration is : CPU: AMD FX 8150 8 cores @ 4.2 GHz RAM: 32 Gb. SSD: 2 x Crucial 240 Gb SATA6 OS: Ubuntu 12.04.3 64 bit WS: Apache 2.2.22 My Apache2 configuration is as follows: /etc/apache2/apache2.conf LockFile ${APACHE_LOCK_DIR}/accept.lock PidFile ${APACHE_PID_FILE} Timeout 30 KeepAlive On MaxKeepAliveRequests 1000000 KeepAliveTimeout 2 ServerName "fnux.net" <IfModule mpm_prefork_module> StartServers 16 MinSpareServers 16 MaxSpareServers 16 ServerLimit 2048 MaxClients 1024 MaxRequestsPerChild 0 </IfModule> User ${APACHE_RUN_USER} Group ${APACHE_RUN_GROUP} AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> DefaultType None HostnameLookups Off ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel emerg Include mods-enabled/*.load Include mods-enabled/*.conf Include httpd.conf Include ports.conf LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %O" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent Include conf.d/ Include sites-enabled/ /etc/apache2/ports.conf NameVirtualHost *:8180 Listen 8180 <IfModule mod_ssl.c> Listen 443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule> /etc/apache2/mods-available <IfModule mod_fastcgi.c> AddHandler php5-fcgi .php Action php5-fcgi /cgi-bin/php5.external <Location "/cgi-bin/php5.external"> Order Deny,Allow Deny from All Allow from env=REDIRECT_STATUS </Location> </IfModule> /etc/apache2/sites-available/default <VirtualHost *:8180> ServerAdmin webmaster@localhost DocumentRoot /var/www/apache2 <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel emerg ##### CustomLog ${APACHE_LOG_DIR}/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> <IfModule mod_fastcgi.c> AddHandler php5-fcgi .php Action php5-fcgi /php5-fcgi Alias /php5-fcgi /usr/lib/cgi-bin/php5-fcgi FastCgiExternalServer /usr/lib/cgi-bin/php5-fcgi -host 127.0.0.1:9000 -pass-header Authorization </IfModule> </VirtualHost> /etc/security/limits.conf * soft nofile 1000000 * hard nofile 1000000 So, I would trully appreciate your advice to setup Apache2 to make it able to sustain 1.000 simultaneous clients, if this is even possible. TIA for your help. Cheers.

  Read the article

• Mongodb: why is my mongo server using two PID's?

  - by Lucas

  I started my mongo with the following command: [lucas@ecoinstance]~/node/nodetest2$ sudo mongod --dbpath /home/lucas/node/nodetest2/data 2014-06-07T08:46:30.507+0000 [initandlisten] MongoDB starting : pid=6409 port=27017 dbpat h=/home/lucas/node/nodetest2/data 64-bit host=ecoinstance 2014-06-07T08:46:30.508+0000 [initandlisten] db version v2.6.1 2014-06-07T08:46:30.508+0000 [initandlisten] git version: 4b95b086d2374bdcfcdf2249272fb55 2c9c726e8 2014-06-07T08:46:30.508+0000 [initandlisten] build info: Linux build14.nj1.10gen.cc 2.6.3 2-431.3.1.el6.x86_64 #1 SMP Fri Jan 3 21:39:27 UTC 2014 x86_64 BOOST_LIB_VERSION=1_49 2014-06-07T08:46:30.509+0000 [initandlisten] allocator: tcmalloc 2014-06-07T08:46:30.509+0000 [initandlisten] options: { storage: { dbPath: "/home/lucas/n ode/nodetest2/data" } } 2014-06-07T08:46:30.520+0000 [initandlisten] journal dir=/home/lucas/node/nodetest2/data/ journal 2014-06-07T08:46:30.520+0000 [initandlisten] recover : no journal files present, no recov ery needed 2014-06-07T08:46:30.527+0000 [initandlisten] waiting for connections on port 27017 It appears to be working, as I can execute mongo and access the server. However, here are the process running mongo: [lucas@ecoinstance]~/node/testSite$ ps aux | grep mongo root 6540 0.0 0.2 33424 1664 pts/3 S+ 08:52 0:00 sudo mongod --dbpath /ho me/lucas/node/nodetest2/data root 6541 0.6 8.6 522140 52512 pts/3 Sl+ 08:52 0:00 mongod --dbpath /home/lu cas/node/nodetest2/data lucas 6554 0.0 0.1 7836 876 pts/4 S+ 08:52 0:00 grep mongo As you can see, there are two PID's for mongo. Before I ran sudo mongod --dbpath /home/lucas/node/nodetest2/data, there were none (besides the grep of course). How did my command spawn two PID's, and should I be concerned? Any suggestions or tips would be great. Additional Info In addition, I may have other issues that might suggest a cause. I tried running mongo with --fork --logpath /home/lucas..., but it did not work. More information below: [lucas@ecoinstance]~/node/nodetest2$ sudo mongod --dbpath /home/lucas/node/nodetest2/data --fork --logpath /home/lucas/node/nodetest2/data/ about to fork child process, waiting until server is ready for connections. forked process: 6578 ERROR: child process failed, exited with error number 1 [lucas@ecoinstance]~/node/nodetest2$ ls -l data/ total 163852 drwxr-xr-x 2 mongodb nogroup 4096 Jun 7 08:54 journal -rw------- 1 mongodb nogroup 67108864 Jun 7 08:52 local.0 -rw------- 1 mongodb nogroup 16777216 Jun 7 08:52 local.ns -rwxr-xr-x 1 mongodb nogroup 0 Jun 7 08:54 mongod.lock -rw------- 1 mongodb nogroup 67108864 Jun 7 02:08 nodetest1.0 -rw------- 1 mongodb nogroup 16777216 Jun 7 02:08 nodetest1.ns Also, my db path folder is not the original location. It was originally created under the default /var/lib/mongodb/ and moved to my local data folder. This was done after shutting down the server via /etc/init.d/mongod stop. I have a Debian Wheezy server, if it matters.

  Read the article

• AWS EC2 instance not pingable or available in browser

  - by Slimmons

  I've seen this questions asked other places, but now I've run through every fix proposed in other questions so I'm re asking it here, in hopes that someone will have a different solution. Problem: I have a EC2 instance, and I can ssh into it and work on it, and I have a Elastic ip set to it. I am unable to ping this machine, or log in to it using my browser. Solutions mentioned and tried: service httpd start i. response I get is "unrecognized service" ii. when I run apache2ctl -k start, it shows "httpd already running", so I'm assuming httpd is not the problem, it's just possibly named something else because of apache2, or for whatever reason. I went into EC2-Security Group- Default (which is the one I used.)-inbound, and everything there is set up correctly (I'm assuming). There it shows 80(HTTP) 0.0.0.0/0. 443(HTTPS) 0.0.0.0/0, and various other servies with their ports and 0.0.0.0/0 next to them. I also enabled a rule for enabling ICMP Request All on 0.0.0.0/0 temporarily for testing purposes I've tried disabling the iptables with "service ufw stop" Just in case I'm doing something really stupid, because I'm not all that used to connecting to web servers that I've spun up, I'm typing in the address to the machine into the url like this (assuming my ip address was ip.address). i. http:/(slash)ip.address/ ii. ip.address iii. https:/(slash)ip.address/ iv. ip.address/webFolderName/ v. http:/(slash)ip.address/webFolderName/ None of the attempts worked, and the only thing I haven't tried that i've seen is to start wireshark on the machine, and see if the requests are reaching it, and it's just ignoring them. I'm not sure I want to do that yet, since A). I'm not 100% positive how to use wireshark without the gui, since it's the only way I've ever used it (I really should get used to it in terminal, but I didn't even know you could). B). It really seems like I'm missing something simple in getting this to work. Thanks in advance for any help.

  Read the article

• smartctl -t long isn't finishing

  - by xenoterracide

  I been running smartctl -t long on a drive for about 2 days now and it seems to be stalled at 10%. short and conveyance both passed. I have to send 1 of 2 drives purchased back I found badblocks with badblocks (none on this drive and I'ts made over a pass already). I'm just wondering if I should be concerned about this. smartctl 5.39.1 2010-01-28 r3054 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: WDC WD10EARS-00Y5B1 Serial Number: WD-WMAV51582123 Firmware Version: 80.00A80 User Capacity: 1,000,204,886,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Mon May 10 22:19:52 2010 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 241) Self-test routine in progress... 10% of test remaining. Total time to complete Offline data collection: (20100) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 231) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 2 3 Spin_Up_Time 0x0027 131 131 021 Pre-fail Always - 6408 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 12 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 148 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 10 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 7 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 174 194 Temperature_Celsius 0x0022 106 102 000 Old_age Always - 41 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Conveyance offline Completed without error 00% 99 - # 2 Extended offline Interrupted (host reset) 10% 30 - # 3 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

  Read the article

• Cassandra hangs with kernel exception when adding jna jar to classpath

  - by george_h

  I have a fresh installation of cassandra v2.0.8 on a RedHat Enterprise Linux v5. I have added a sym link of the jna.jar in cassandra's /lib folder. I start cassandra and it hangs after printing out the classpath in the terminal. When I check my /var/log/message I see this message Jun 9 07:19:05 Bigdata1 kernel: INFO: task java:4889 blocked for more than 120 seconds. Jun 9 07:19:05 Bigdata1 kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Jun 9 07:19:05 Bigdata1 kernel: java D ffffffff8006272c 0 4889 1 4890 4888 (NOTLB) Jun 9 07:19:05 Bigdata1 kernel: ffff81022972ba08 0000000000000082 ffffffffffffffff ffffffffffffffff Jun 9 07:19:05 Bigdata1 kernel: ffffffffffffffff 0000000000000006 ffff81022c61c0c0 ffff81022fe6d7f0 Jun 9 07:19:05 Bigdata1 kernel: 0000006c16aa1b88 0000000000002704 ffff81022c61c2a8 00000005ffffffff Jun 9 07:19:05 Bigdata1 kernel: Call Trace: Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff8006468c>] __down_read+0x7a/0x92 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff800a6d77>] futex_wake+0x24/0xd4 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff8003e6c1>] do_futex+0x329/0xd42 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff8008ee54>] enqueue_task+0x41/0x56 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff8008eebf>] __activate_task+0x56/0x6d Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff80047297>] try_to_wake_up+0x472/0x484 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff8008eca2>] dequeue_task+0x18/0x37 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff800a7ee6>] sys_futex+0x11f/0x140 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff800a7d03>] exit_robust_list+0x51/0x115 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff80035857>] mm_release+0xac/0xc0 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff800421e9>] exit_mm+0x16/0xf7 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff800158d6>] do_exit+0x2e7/0x931 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff8004953a>] cpuset_exit+0x0/0x88 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff8002b96c>] get_signal_to_deliver+0x465/0x494 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff8005b090>] do_notify_resume+0x9c/0x7af Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff80131c1f>] avc_has_perm+0x46/0x58 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff8008f4a9>] default_wake_function+0x0/0xe Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff8008ea17>] set_load_weight+0x98/0xb2 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff800624c6>] __sched_text_start+0xf6/0xbd0 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff8008ec58>] task_rq_lock+0x3d/0x6f Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff8008ee54>] enqueue_task+0x41/0x56 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff800bb684>] audit_syscall_exit+0x329/0x344 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff800a7ee6>] sys_futex+0x11f/0x140 Jun 9 07:19:05 Bigdata1 kernel: [<ffffffff8005d33e>] int_signal+0x12/0x17 The only way to stop it is by rebooting the server. If I remove the jna.jar symlink then everything is fine. Anyone know why this is happening ?

  Read the article

• Turn off email notification from abrt (Automatic Bug Reporting Tool)

  - by Banjer

  I'm configuring CentOS 6.2 and have seen a few "[abrt] full crash report" emails. I understand that abrt is useful for creating crash dumps and what not, so I don't want to disable the service, I just would like to stop getting the crash report emails. I probably have to add something to the config file in /etc/abrt/abrt.conf. I can't seem to find anything in my searches. Any idea? Thanks. Edit: Here is my abrt.conf, which is rather simple. [root@myhost~]# cat /etc/abrt/abrt.conf # Enable this if you want abrtd to auto-unpack crashdump tarballs which appear # in this directory (for example, uploaded via ftp, scp etc). # Note: you must ensure that whatever directory you specify here exists # and is writable for abrtd. abrtd will not create it automatically. # #WatchCrashdumpArchiveDir = /var/spool/abrt-upload # Max size for crash storage [MiB] or 0 for unlimited # MaxCrashReportsSize = 1000 # Specify where you want to store coredumps and all files which are needed for # reporting. (default:/var/spool/abrt) # #DumpLocation = /var/spool/abrt And a listing of /etc/abrt: [root@myhost~]# ls -la /etc/abrt total 32 drwxr-xr-x. 3 root root 4096 Apr 13 06:14 . drwxr-xr-x. 97 root root 12288 Apr 13 03:50 .. -rw-r--r--. 1 root root 527 Dec 13 22:50 abrt-action-save-package-data.conf -rw-r--r--. 1 root root 572 Dec 13 22:50 abrt.conf -rw-r--r--. 1 root root 175 Dec 13 22:50 gpg_keys drwxr-xr-x. 2 root root 4096 Apr 13 06:13 plugins [root@myhost~]# ls -la /etc/abrt/plugins/ total 12 drwxr-xr-x. 2 root root 4096 Apr 13 06:13 . drwxr-xr-x. 3 root root 4096 Apr 13 06:14 .. -rw-r--r--. 1 root root 278 Dec 13 22:50 CCpp.conf Actually all of those conf files above are only a few lines and do not mention anything about mail, email, or notifications.

  Read the article

• How to properly shutdown a Linux VMware Server Host

  - by Mikee

  Hi Everybody: In our lab, we have a server running Ubuntu Linux 8.04.4 x64, with VMware Server 2.1 hosting 4 VM's. I have a major concern with regards to shutting down the host server. Mostly, how do I ensure that the guest VM's are being shut down safely? In the VMware web interface console, I have enabled: "Allow virtual machines to start and stop automatically with the system" I enabled the Default Startup Delay for 15 seconds along with the "Start next VM immediately if the VMware Tools start" option checked I enabled the Default Shutdown Delay with a 60 second shutdown delay and a Shutdown Action of "Shut Down Guest" All VM's have the VMware Tools installed and properly working. All VM's are moved up into the "Specified Order" section of "Startup Order", thus when powering the server back on, all those VM's should start up again in that specified order. When I went to shut down the server, I used the shutdown -h now command. Based on the settings I entered above, I was expecting a 4 minute shutdown, as there is an option to delay the shutdown of each VM by 60 seconds. However, that is not what happened. Instead, the server shutdown in under a minute. When I powered the server back on, only 2 VM's properly loaded. The other 2 showed the following error: "Power on Virtual Machine" failed to complete If these problems problems persist, please contact your system administrator. Details: Cannot open the disk '[location to .vmdk]' or one of the snapshot disks it depends on. Reason: Failed to lock the file. Obviously, if this error occured, then it is clear to me that the VM's were not properly shutdown, or the server powered off before the VM's were completely shutdown. I have fixed the above error by deleting the .lck files in the respective VM directories. How would I know if the VM's were properly shut down? I checked the VMware-server logs, but they only seem to display the logs of when the vmware-mgmt service is running in the current session. I'm mostly running Linux VM's, so is there an easy way to know whether or not a server was properly shut down in Linux? Thank you all for the help!

  Read the article

• Specifying network settings during SLES 11 auto installation

  - by banjer

  I'm setting up an autoinst.xml file for auto-installing SLES 11. I get prompted for the various interface settings per below, but they don't seem to stick once the server reboots. I don't think I have the xml defined correctly. I'm hoping someone has experience with this. <ask-list> <ask> <path>networking,dns,hostname</path> <question>Enter Hostname (server name)</question> <stage>initial</stage> <default>merkin</default> </ask> <ask> <path>networking,interfaces,interface,0,device</path> <question>Enter the primary ethernet device:</question> <stage>initial</stage> <default>eth0</default> </ask> <ask> <path>networking,interfaces,interface,0,ipaddr</path> <question>Enter the primary IP Address:</question> <stage>initial</stage> </ask> <ask> <path>networking,interfaces,interface,0,netmask</path> <question>Enter the Netmask Address:</question> <stage>initial</stage> </ask> <ask> <path>networking,routing,routes,route,0,gateway</path> <question>Enter the primary Gateway Address:</question> <stage>initial</stage> </ask> </ask-list> The first one for hostname seems to be sticking just fine, but the rest do not. As an alternative, is there a way to stop the autoinstall at the section where you configure the network devices so that the user can take over? I was able to show the partition proposal, but not sure how to do the same with the networking setup.

  Read the article

• How to connect to a Virtualbox guest from the host when network cable unplugged

  - by Greg K

  I'd like to work offline (I'm flying to the US twice this month), to do this I need access to a linux development server. When I work from home I boot a VirtualBox VM and that acts as my dev server for the day (providing Apache, PHP & MySQL to run my server side code). However, I'd like to work with my VM when I'm not connected to a network. I have my Ubuntu VM guest set up with a bridge connection so it can serve HTTP and provide SSH access from inside my local network. I've tried to manually configure my network settings on both Mac OSX (the host) and Ubuntu (the guest) but I can't even ping my own NIC address (127.0.0.1 can, 192.168.21.x I can't) in OS X when I unplug the cable. Manual network settings: $ ifconfig en0 en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:xx:xx:xx:xx:xx inet 192.168.21.5 netmask 0xffffff00 broadcast 192.168.21.255 media: autoselect (100baseTX <full-duplex,flow-control>) status: active I can ping localhost fine, as well as my VM (.20) and SSH too. $ ping 192.168.21.5 PING 192.168.21.5 (192.168.21.5): 56 data bytes 64 bytes from 192.168.21.5: icmp_seq=0 ttl=64 time=0.085 ms 64 bytes from 192.168.21.5: icmp_seq=1 ttl=64 time=0.102 ms 64 bytes from 192.168.21.5: icmp_seq=2 ttl=64 time=0.100 ms 64 bytes from 192.168.21.5: icmp_seq=3 ttl=64 time=0.094 ms $ ping 192.168.21.20 PING 192.168.21.20 (192.168.21.20): 56 data bytes 64 bytes from 192.168.21.20: icmp_seq=0 ttl=64 time=0.910 ms 64 bytes from 192.168.21.20: icmp_seq=1 ttl=64 time=1.181 ms 64 bytes from 192.168.21.20: icmp_seq=2 ttl=64 time=1.159 ms 64 bytes from 192.168.21.20: icmp_seq=3 ttl=64 time=1.320 ms Network cable unplugged: $ ifconfig en0 en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:xx:xx:xx:xx:xx media: autoselect status: inactive $ ping 192.168.21.5 PING 192.168.21.5 (192.168.21.5): 56 data bytes ping: sendto: No route to host ping: sendto: No route to host Request timeout for icmp_seq 0 ping: sendto: No route to host Request timeout for icmp_seq 1 Does OS X disable the NIC when the network cable is unplugged? Any way to stop it doing this?

  Read the article

• What other protocols must not be fire-walled for FTP to work?

  - by Chris

  my Netgear router randomly reset itself the other day loosing all of my config settings: DSL details, Firewall rules, the lot! So I set about restoring all of the details manually, but when it came to configuring the firewall I wanted improve the security by explicitly setting 'deny' rules for everything that I figured is 'non-essential', and (although not necessary) whilst I was at it I set explicit 'allow' for the 'essential' protocols. I'll admit now I didn't really know what I was doing and everything was just 'my best guess', but I enabled only DNS, HTTP, HTTPS, FTP, SFTP, TFTP with everything else blocked. This did not work for me as I could not access 99% of web sites (although strangely Google worked!), so I played around a bit more and found that (oddly) if I disabled just the explicit 'allow' rules then everything worked fine, for browsing anyway. Today I came to work on some web-sites via FTP and just could not get a consistent connection, it kept dropping out after a few files or being blocked by the server or simply not connecting. It would authenticate okay but then stop when retrieving the initial directory listing! e.g.: Status: Delaying connection for 1 second due to previously failed connection attempt... Status: Resolving address of ftp.domain.co.uk Status: Resolving address of ftp.domain.co.uk Status: Connecting to 123.123.123.123:21... Status: Connecting to 123.123.123.123:21... Status: Connection established, waiting for welcome message... Status: Connection established, waiting for welcome message... Response: 421 Too many connections (8) from this IP Error: Could not connect to server Status: Delaying connection for 5 seconds due to previously failed connection attempt... Response: 421 Too many connections (8) from this IP Error: Could not connect to server Status: Delaying connection for 5 seconds due to previously failed connection attempt... I've checked and re-checked the FTP settings (they worked before anyway), I have Googled the I.T. out of the various protocols that I have blocked in the fire-wall but none seem essential to FTP (other than FTP/SFTP etc. which I have passively enabled). I'm (clearly) no server engineer, or protocols / fire-wall expert so I was hoping that some one could maybe shed some light on why my FTP is failing. I've been wondering if I ought to be allowing BGP, BOOTP and/or IDENT (or any others)? What other protocols are required for FTP? Thanks in advance!

  Read the article

• keyboard mappings are totally screwed after updating to kde4

  - by zeonglow

  I recently upgraded from KDE 3.5 to KDE 4, and I have been having weird issues with my keyboard. In one of the virtual consoles e.g. when I press ctrl + alt 1 , I can type perfectly, but in KDE, several of the number keys don't work, the left and right arrows don't work either. When I press the right arrow key in xev I get this: KeyRelease event, serial 34, synthetic NO, window 0x3600001, root 0x6f, subw 0x0, time 903459, (111,55), root:(115,836), state 0x10, keycode 114 (keysym 0x1008ff11, XF86AudioLowerVolume), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False When I press the '3' key it toggles my Bookmarks toolbar in Firefox, in xev I get this: KeyPress event, serial 34, synthetic NO, window 0x3600001, root 0x6f, subw 0x0, time 999968, (94,115), root:(98,896), state 0x10, keycode 12 (keysym 0x1008ff30, XF86Favorites), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyRelease event, serial 34, synthetic NO, window 0x3600001, root 0x6f, subw 0x0, time 1000032, (94,115), root:(98,896), state 0x10, keycode 12 (keysym 0x1008ff30, XF86Favorites), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False As this is deeper down, changing the type of keyboard in the KDE meun's has no effect. I'm slowly beginning to wade through the mountains of documentation about the X keyboard model, but there has to be a better way. Does anyone no what it is? Edit: 1234567890 ! after deleting the entire .kde folder. but only until I change the Keyboard settings from the "system settings" applet, then its hosed full time. Regardless of what I set the settings too. (restore to default settings doesn't) 2nd Edit: I'm using Gentoo AMD64, I was upgrading from KDE 3.5 KDE 4.2. I think I had manual settings before, although I didn't change anything. I was originally running KDE without HAL until that stop working a year or so ago. The only customisation I made was to set the multimedia keys to control Amarok. 3rd Edit $ grep xkb /var/log/Xorg.0.log (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "evdev" (**) Option "xkb_layout" "us" (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "evdev" (**) Option "xkb_layout" "us" Xorg.0.log has this to say: (WW) AllowEmptyInput is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled. (WW) Disabling Mouse1 (WW) Disabling Keyboard1 My Xorg.conf has this in it. Identifier "Keyboard1" Driver "kbd" Option "AutoRepeat" "500 30" # Specify which keyboard LEDs can be user-controlled (eg, with xset(1)) Option "XkbRules" "xorg" Option "XkbModel" "pc105" Option "XkbLayout" "gb"

  Read the article

• iCloud stuff stops working while connected to OpenVPN [closed]

  - by Taco Bob

  I have a fairly simple OpenVPN setup on an OpenVZ VPS with Ubuntu 11.10. Client is the Viscosity client on Mac OS X 10.8.2, and after some testing, we can rule out the client as being part of the problem. Everything has been working fine except for Apple's iCloud stuff. Web surfing, email, FTP, NNTP, and Skype are all working as expected. It's ONLY the iCloud services that cease to function. If I connect to the VPN, iCloud stuff stops working. I no longer get anything in Messages, Calendar items don't get updated, and Notifications stop working. If I disconnect, the iCloud stuff all starts working. Connect again, iCloud stops working. Here's the server.conf: status openvpn-status.log log /var/log/openvpn.log verb 4 port 1194 proto udp dev tun ca /etc/openvpn/ca.crt cert /etc/openvpn/server.crt key /etc/openvpn/server.key dh /etc/openvpn/dh1024.pem server 10.9.8.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1" push “dhcp-option DNS 10.9.8.1? keepalive 10 120 duplicate-cn cipher BF-CBC comp-lzo user nobody group nogroup persist-key persist-tun tun-mtu 1500 mssfix 1400 I'm using iptables in a script, and it's also fairly simplistic. iptables -F iptables -t nat -F iptables -t mangle -F iptables -A FORWARD -i tun0 -o venet0 -j ACCEPT iptables -A FORWARD -i venet0 -o tun0 -j ACCEPT iptables -A INPUT -p tcp --dport 22 -j ACCEPT iptables -A INPUT -p tcp --dport 1194 -j ACCEPT iptables -A INPUT -p udp --dport 1194 -j ACCEPT iptables -t nat -A POSTROUTING -s 10.9.8.0/24 -j SNAT --to-source <server's public ip> echo 1 > /proc/sys/net/ipv4/ip_forward I tried forwarding ports as well, with no success. iptables -A FORWARD -p tcp -d 10.9.8.0/24 --dport 5222:5230 -j ACCEPT iptables -t nat -A PREROUTING -p tcp --dport 5222:5230 -j DNAT --to-destination 10.9.8.6 I am also sometimes behind a double-NAT situation that I have no control over. Client -> work VPN -> my OpenVPN box -> Internet. Client -> Airport Express -> ISP (which is doing NAT) -> my OpenVPN box -> Internet. Those two situations are just the fact of life where I am, and I cannot change them. I do have full control over my client and the OpenVPN server. I am completely out of ideas. I have posted a similar query at the OpenVPN forums, but it hasn't posted yet and seems to be in their moderation queue still. Tried on freenode irc channels, but nobody is awake, so here I am. I have Googled extensively for this, and can find nothing that is related. Help me get iCloud stuff working again!

  Read the article

• multi-user rvm gem install failure when called from CloudFormation::Init

  - by Peter Mounce

  I've taken an Amazon Linux AMI (based on CentOS) and installed RVM (1.10.3) to it in multi-user fashion (see {1} below). I used that to install ruby 1.9.3-p125, rubygems 1.8.17, and bundler 1.1 as the baseline requirements for most things I'm going to be using the instances for. I've captured that instance to an AMI, and am now launching it via CloudFormation, with some CloudFormation::Init commands. One of them is to use s3cmd to pull down a private gem from S3, and the next one, the one that fails, is to install that gem. It fails with an error message 2012-03-15 16:53:20,201 [ERROR] Command 20_install_gems (/usr/local/rvm/rubies/ruby-1.9.3-p125/bin/gem install ./*.gem) failed 2012-03-15 16:53:20,202 [DEBUG] Command 20_install_gems output: /usr/local/rvm/rubies/ruby-1.9.3-p125/bin/gem:12:in `require': no such file to load -- rubygems (LoadError) from /usr/local/rvm/rubies/ruby-1.9.3-p125/bin/gem:12 Now, that happens during the cfn-init execution - I assume, but haven't checked yet, that cfn-init is being run with an environment different from that of ec2-user (there are no other users on the instance). If I run gem install mygem.gem in an interactive session then that works fine. So, my question really, is what should I do to make this work for cfn-init? Have I correctly set up rvm as multi-user? I've confirmed that cfn-init is being run as the root user, with his restricted environment. How should I source the /etc/profile.d/rvm.sh into root's sessions? {1} My semi-automated rvm installation steps (run in interactive session as ec2-user): sudo bash -s stable < <(curl -s https://raw.github.com/wayneeseguin/rvm/master/binscripts/rvm-installer ) sudo gpasswd -a ec2-user rvm # iconv-devel is baked into centos' glibc sudo yum install -y autoconf automake bison bzip2 gcc-c++ git libffi-devel libtool libxml2-devel libxslt-devel libyaml-devel make openssl-devel patch readline readline-devel zlib zlib-devel source /etc/profile.d/rvm.sh rvm list known # in a new session: rvm install ruby-1.9.3-p125 rvm use 1.9.3 --default gem update --system # gems required by public_web-awareness gem install aws-sdk bundler cocaine sinatra echo -e "gem: --no-ri --no-rdoc\n" > /home/ec2-user/.gemrc # delete unnecessary documentation files rm -rf `gem env gemdir`/doc sudo -s sudo echo -e "gem: --no-ri --no-rdoc\n" > /etc/skel/.gemrc sudo echo -e "gem: --no-ri --no-rdoc\n" > /etc/gemrc # ctrl + d out of the sudo session Some environment information: [ec2-user@ip ~]$ echo $PATH /usr/local/rvm/gems/ruby-1.9.3-p125/bin:/usr/local/rvm/gems/ruby-1.9.3-p125@global/bin:/usr/local/rvm/rubies/ruby-1.9.3-p125/bin:/usr/local/rvm/bin:/usr/local/bin:/bin:/usr/bin:/usr/local/sbin:/usr/sbin:/sbin:/opt/aws/bin:/home/ec2-user/bin [ec2-user@ip ~]$ echo $GEM_HOME /usr/local/rvm/gems/ruby-1.9.3-p125 [ec2-user@ip ~]$ echo $GEM_PATH /usr/local/rvm/gems/ruby-1.9.3-p125:/usr/local/rvm/gems/ruby-1.9.3-p125@global [ec2-user@ip ~]$ echo $BUNDLE_PATH [ec2-user@ip ~]$ gem list *** LOCAL GEMS *** aws-sdk (1.3.6) bundler (1.1.0) cocaine (0.2.1) httparty (0.8.1) json (1.6.5) multi_json (1.1.0) multi_xml (0.4.1) nokogiri (1.5.1, 1.5.0) rack (1.4.1) rack-protection (1.2.0) rake (0.9.2) sinatra (1.3.2) tilt (1.3.3) uuidtools (2.1.2) yamler (0.1.0)

  Read the article

• "No route to host" with ssl but not with telnet

  - by Clemens Bergmann

  I have a strange problem with connecting to a https site from one of my servers. When I type: telnet puppet 8140 I am presented with a standard telnet console and can talk to the Server as always: Connected to athena.hidden.tld. Escape character is '^]'. GET / HTTP/1.1 <!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML 2.0//EN"> <html><head> <title>400 Bad Request</title> </head><body> <h1>Bad Request</h1> <p>Your browser sent a request that this server could not understand.<br /> Reason: You're speaking plain HTTP to an SSL-enabled server port.<br /> Instead use the HTTPS scheme to access this URL, please.<br /> <blockquote>Hint: <a href="https://athena.hidden.tld:8140/"><b>https://athena.hidden.tld:8140/</b></a></blockquote></p> <hr> <address>Apache/2.2.16 (Debian) Server at athena.hidden.tld Port 8140</address> </body></html> Connection closed by foreign host. But when I try to connect to the same host and port with ssl: openssl s_client -connect puppet:8140 It is not working connect: No route to host connect:errno=113 I am confused. At first it sounded like a firewall problem but this could not be, could it? Because this would also prevent the telnet connection. As Firewall I am using ferm on both servers. The systems are debian squeeze vm-boxes. [edit 1] Even when I try to connect directly with the IP address: openssl s_client -connect 198.51.100.1:8140 #address exchanged connect: No route to host connect:errno=113 Bringing down the firewalls on both hosts with service ferm stop is also not helping. But when I do openssl s_client -connect localhost:8140 on the server machine it is connecting fine. [edit 2] if I connect to the IP with telnet it also is not working. telnet 198.51.100.1 8140 Trying 198.51.100.1... telnet: Unable to connect to remote host: No route to host The confusion might come from IPv6. I have IPv6 on all my hosts. It seems that telnet uses IPv6 by default and this works. For example: telnet -6 puppet 8140 works but telnet -4 puppet 8140 does not work. So there seems to be a problem with the IPv4 route. openssl seems to only (or by default) use IPv4 and therefore fails but telnet uses IPv6 and succeeds.

  Read the article

• Debugging IO limitation

  - by Martin F

  I have a Fedora box with some severe IO limitations which I have no idea how to debug. The server has a Areca Technology Corp. ARC-1130 12-Port PCI-X to SATA RAID Controller with 12 7200 RPM 1.5 TB disks and a Marvell Technology Group Ltd. 88E8050 PCI-E ASF Gigabit Ethernet Controller. uname -a output: 2.6.32.11-99.fc12.x86_64 #1 SMP Mon Apr 5 19:59:38 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux The server is a file server running Nginx with the stub status module enabled, so I can see the current amount of connections. The problem present itself when I have a high number of simultaneous connections in a writing state. Usually around 350, at this very moment it's at 590 and the server is almost unusable and stuck at 230mbit/s. If I run stop and hit 1 to see CPU core usages I have all 4 cores with around 99% io wait, if I run iotop the nginx workers are the only processes producing any read load, currently at around 25MB/s. I have each of the workers bound to their own core. Initially I figured it was just the disks being bugged. But I've run fscheck and smartmontools checks and found no errors. I also ran an iozone test which you can see the result of here: http://www.pastie.org/951667.txt?key=fimcvljulnuqy2dcdxa Additionally, when the amount of connections are low I have no problem getting a good speed. If I wget over the local network it easily hits 60MB/sec. Right now I just tried putting a file in /dev/shm, then I symlinked a file from the public dir to it and used wget over the local network and only got 50KB/s. Also, if I try to cp /dev/shm/test /root/test it quickly copies around 740MB and then slows down HEAVILY. Again with iotop reporting 99% iowait. I'm not really sure how to go about figuring out what the problems are. It could be a natural disk limitation but then the file from /dev/shm ought to transfer so it seems there's a network limit, but that's fine when there's not many connections. Perhaps it's a TCP stack problem but I really have no idea how to check that. Any suggestions on how to proceed with debugging would be very welcome. If additional information is required then let me know and I'll try to get it. Thanks.

  Read the article

• innobackupex - after restoring - quit without updating PID file

  - by clarkk

  After restoring a backup the server can't start.. restoring # tar -izxf /var/www/bak/db/2013-11-10-1437_mysql.tar.gz -C /var/www/bak/db_import # innobackupex --use-memory=1G --apply-log /var/www/bak/db_import # service mysql stop # mv /var/lib/mysql /var/lib/mysql-old # mkdir /var/lib/mysql # innobackupex --copy-back /var/www/bak/db_import # chown -R mysql:mysql /var/lib/mysql # service mysql start error log 131110 21:24:20 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql 2013-11-10 21:24:21 0 [Warning] TIMESTAMP with implicit DEFAULT value is deprecated. Please use --explicit_defaults_for_timestamp server option (see documentation for more details). 2013-11-10 21:24:21 6194 [Warning] Using pre 5.5 semantics to load error messages from /opt/mysql/server-5.6/share/english/. 2013-11-10 21:24:21 6194 [Warning] If this is not intended, refer to the documentation for valid usage of --lc-messages-dir and --language parameters. 2013-11-10 21:24:21 6194 [Note] Plugin 'FEDERATED' is disabled. /usr/local/mysql/bin/mysqld: Table 'mysql.plugin' doesn't exist 2013-11-10 21:24:21 6194 [ERROR] Can't open the mysql.plugin table. Please run mysql_upgrade to create it. 2013-11-10 21:24:21 6194 [Note] InnoDB: The InnoDB memory heap is disabled 2013-11-10 21:24:21 6194 [Note] InnoDB: Mutexes and rw_locks use GCC atomic builtins 2013-11-10 21:24:21 6194 [Note] InnoDB: Compressed tables use zlib 1.2.3 2013-11-10 21:24:21 6194 [Note] InnoDB: Using Linux native AIO 2013-11-10 21:24:21 6194 [Note] InnoDB: Not using CPU crc32 instructions 2013-11-10 21:24:21 6194 [Note] InnoDB: Initializing buffer pool, size = 128.0M 2013-11-10 21:24:21 6194 [Note] InnoDB: Completed initialization of buffer pool 2013-11-10 21:24:21 6194 [Note] InnoDB: Highest supported file format is Barracuda. 2013-11-10 21:24:22 6194 [Note] InnoDB: 128 rollback segment(s) are active. 2013-11-10 21:24:22 6194 [Note] InnoDB: Waiting for purge to start 2013-11-10 21:24:22 6194 [Note] InnoDB: 5.6.12 started; log sequence number 636992658 2013-11-10 21:24:22 6194 [Note] Server hostname (bind-address): '127.0.0.1'; port: 3306 2013-11-10 21:24:22 6194 [Note] - '127.0.0.1' resolves to '127.0.0.1'; 2013-11-10 21:24:22 6194 [Note] Server socket created on IP: '127.0.0.1'. 2013-11-10 21:24:22 6194 [ERROR] Fatal error: Can't open and lock privilege tables: Table 'mysql.user' doesn't exist 131110 21:24:22 mysqld_safe mysqld from pid file /var/run/mysqld/mysqld.pid ended mysql_upgrade /opt/mysql/server-5.6/bin/mysql_upgrade -u root -pxxxxx -P 3308 Warning: Using a password on the command line interface can be insecure. Looking for 'mysql' as: /opt/mysql/server-5.6/bin/mysql Looking for 'mysqlcheck' as: /opt/mysql/server-5.6/bin/mysqlcheck FATAL ERROR: Upgrade failed

  Read the article

• How to troubleshoot a PHP script that causes a Segmenation Fault?

  - by johnlai2004

  I posted this on stackoverflow.com as well because I'm not sure if this is a programming problem or a server problem. I'm using ubuntu 9.10, apache2, mysql5 and php5. I've noticed an unusual problem with some of my php programs. Sometimes when visiting a page like profile.edit.php, the browser throws a dialogue box asking to download profile.edit.php page. When I download it, there's nothing in the file. profile.edit.php is supposed to be a web form that edits user information. I've noticed this on some of my other php pages as well. I look in my apache error logs, and I see a segmentation fault message: [Mon Mar 08 15:40:10 2010] [notice] child pid 480 exit signal Segmentation fault (11) And also, the issue may or may not appear depending on which server I deploy my application too. Additonal Details This doesn't happen all the time though. It only happens sometimes. For example, profile.edit.php will load properly. But as soon as I hit the save button (form action="profile.edit.php?save=true"), then the page asks me to download profile.edit.php. Could it be that sometimes my php scripts consume too much resources? Sample code Upon save action, my profile.edit.php includes a data_access_object.php file. I traced the code in data_access_object.php to this line here if($params[$this->primaryKey]) { $q = "UPDATE $this->tableName SET ".implode(', ', $fields)." WHERE ".$this->primaryKey." = ?$this->primaryKey"; $this->bind($this->primaryKey, $params[$this->primaryKey], $this->tblFields[$this->primaryKey]['mysqlitype']); } else { $q = "INSERT $this->tableName SET ".implode(', ', $fields); } // Code executes perfectly up to this point // echo 'print this'; exit; // if i uncomment this line, profile.edit.php will actually show 'print this'. If I leave it commented, the browser will ask me to download profile.edit.php if(!$this->execute($q)){ $this->errorSave = -3; return false;} // When I jumped into the function execute(), every line executed as expected, right up to the return statement. And if it helps, here's the function execute($sql) in data_access_object.php function execute($sql) { // find all list types and explode them // eg. turn ?listId into ?listId0,?listId1,?listId2 $arrListParam = array_bubble_up('arrayName', $this->arrBind); foreach($arrListParam as $listName) if($listName) { $explodeParam = array(); $arrList = $this->arrBind[$listName]['value']; foreach($arrList as $key=>$val) { $newParamName = $listName.$key; $this->bind($newParamName,$val,$this->arrBind[$listName]['type']); $explodeParam[] = '?'.$newParamName; } $sql = str_replace("?$listName", implode(',',$explodeParam), $sql); } // replace all ?varName with ? for syntax compliance $sqlParsed = preg_replace('/\?[\w\d_\.]+/', '?', $sql); $this->stmt->prepare($sqlParsed); // grab all the parameters from the sql to create bind conditions preg_match_all('/\?[\w\d_\.]+/', $sql, $matches); $matches = $matches[0]; // store bind conditions $types = ''; $params = array(); foreach($matches as $paramName) { $types .= $this->arrBind[str_replace('?', '', $paramName)]['type']; $params[] = $this->arrBind[str_replace('?', '', $paramName)]['value']; } $input = array('types'=>$types) + $params; // bind it if(!empty($types)) call_user_func_array(array($this->stmt, 'bind_param'), $input); $stat = $this->stmt->execute(); if($GLOBALS['DEBUG_SQL']) echo '<p style="font-weight:bold;">SQL error after execution:</p> ' . $this->stmt->error.'<p>&nbsp;</p>'; $this->arrBind = array(); return $stat; }

  Read the article

• lighttpd: weird behavior on multiple rewrite rule matches

  - by netmikey

  I have a 20-rewrite.conf for my php application looking like this: $HTTP["host"] =~ "www.mydomain.com" { url.rewrite-once += ( "^/(img|css)/.*" => "$0", ".*" => "/my_app.php" ) } I want to be able to put the webserver in kind of a "maintenance" mode while I update my application from scm. To do this, my idea was to enable an additional rewrite configuration file before this one. The 16-rewrite-maintenance.conf file looks like this: url.rewrite-once += ( "^/(img|css)/.*" => "$0", ".*" => "/maintenance_app.php" ) Now, on the maintenance page, I have a logo that doesn't get loaded. I get a 404 error. Lighttpd debug says the following: 2012-12-13 20:28:06: (response.c.300) -- splitting Request-URI 2012-12-13 20:28:06: (response.c.301) Request-URI : /img/content/logo.png 2012-12-13 20:28:06: (response.c.302) URI-scheme : http 2012-12-13 20:28:06: (response.c.303) URI-authority: localhost 2012-12-13 20:28:06: (response.c.304) URI-path : /img/content/logo.png 2012-12-13 20:28:06: (response.c.305) URI-query : 2012-12-13 20:28:06: (response.c.300) -- splitting Request-URI 2012-12-13 20:28:06: (response.c.301) Request-URI : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.302) URI-scheme : http 2012-12-13 20:28:06: (response.c.303) URI-authority: localhost 2012-12-13 20:28:06: (response.c.304) URI-path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.305) URI-query : 2012-12-13 20:28:06: (response.c.349) -- sanatising URI 2012-12-13 20:28:06: (response.c.350) URI-path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (mod_access.c.135) -- mod_access_uri_handler called 2012-12-13 20:28:06: (response.c.470) -- before doc_root 2012-12-13 20:28:06: (response.c.471) Doc-Root : /www 2012-12-13 20:28:06: (response.c.472) Rel-Path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.473) Path : 2012-12-13 20:28:06: (response.c.521) -- after doc_root 2012-12-13 20:28:06: (response.c.522) Doc-Root : /www 2012-12-13 20:28:06: (response.c.523) Rel-Path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.524) Path : /www/img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.541) -- logical -> physical 2012-12-13 20:28:06: (response.c.542) Doc-Root : /www 2012-12-13 20:28:06: (response.c.543) Rel-Path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.544) Path : /www/img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.561) -- handling physical path 2012-12-13 20:28:06: (response.c.562) Path : /www/img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.618) -- file not found 2012-12-13 20:28:06: (response.c.619) Path : /www/img/content/logo.png, /img/content/logo.png Any clue on why lighttpd matches both rules (from my application rewrite config and from my maintenance rewrite config) and concatenates them with a comma - that doesn't seem to make any sense?! Shouldn't it stop after the first match with rewrite-once?

  Read the article

• Windows Setup could not configure Windows to run on this computer's hardware

  - by Hello71

  The whole installation goes smoothly up to the point of "Completing installation ...". The monitor changes resolution, after which a standard dialog box pops up saying Windows Setup could not configure Windows to run on this computer's hardware Then, in a few seconds, the whole machine powers down. Trying to restart produces the message: STOP: c000021a {Fatal System Error} 0x00000000 (0xc0000001 0x00100448) OR it boots into Setup and comes up with the message: Windows Setup encountered an unexpected error... (This is not the actual error, just paraphrasing) I tried using the OEM restore instead of a regular install, but it fails with the same error. (Even though it worked before...) General specs: HP Pavilion Elite e9262f Intel Core i5-750 Processor ATI Radeon HD 4650 Hitachi HDT721010SLA360 ATA Device 6GB DDR3 RAM SuperMulti DVD Burner with LightScribe Some built-in Wi-Fi module http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01916917 I've tried disconnecting the wireless card and disabling the built-in Ethernet and Firewire via the BIOS, and replacing the wireless keyboard and mouse with wired USB ones. Didn't work. I've also tried changing the SATA controller settings in the BIOS to RAID, AHCI, and IDE, reinstalling each time I changed. Still not working. I think the reason why it is showing the Fatal System Error is because it didn't finish installing before it errored out and shut down, so the system is left in an inconsistent state. I've tried 3 different copies (including the OEM restore) of Windows 7 now, and they're all failing at the same point, with the same error message. I've tried to install Windows 7 maybe 10 times already, with the exact same error message at the exact same location. Hm... Interestingly, the 32-bit version of Windows 7 works, but the 64-bit version doesn't. Perhaps it was a badly burned disk? Reburning the 64-bit version still comes up with the same error. Here's a picture of the side of the case that clearly says it came with Windows 7 64-bit, along with the model number and CPU. sudo fdisk -l: Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009896f Device Boot Start End Blocks Id System /dev/sda1 * 1 13 104391 7 HPFS/NTFS /dev/sda2 14 94119 755906445 7 HPFS/NTFS /dev/sda3 119922 121602 13492224 7 HPFS/NTFS /dev/sda4 94120 119922 207257740+ 5 Extended /dev/sda5 119527 119922 3170769 82 Linux swap / Solaris /dev/sda6 107174 119526 99225441 83 Linux /dev/sda7 94120 107173 104856192 7 HPFS/NTFS Partition table entries are not in disk order

  Read the article

• Effecient organization of spare cables and hardware

  - by Jake Wharton

  As many of you also likely do, I have a growing collection of cables, hardware, and spare parts (screws, connectors, etc.). I'm looking to find a good system of organization so that everything isn't a tangled mess, mismatched, and potentially able to be damaged. Since the the three things listed above are all have varying sizes and degrees of delicacy this poises an interesting problem. Presently I have those cheap plastic storage bins you find at Wal-mart for everything. Cables that were once wrapped neatly have become tangled due to numerous "I know I have a cable for this" moments. Hardware is mixed in other bins with odds and ends with no protection from each other. NICs, CPUs, and HDDs are all interacting and likely causing damage. Finally there are stray parts sprinkled amongst these two both in plastic bags and loose. I'm looking to unify this storage into a controlled chaos. Here are my thoughts: Odds and ends are the easiest. Screws, connectors, and small electronic parts lend themselves perfectly to tackle boxes and jewelry boxes. Since these are usually dynamically compartmentalized I can adjust for the contents and label them on the outside or inside of the lid. Cables are easily wrangled with short velcro strips but that doesn't stop them from being all mixed in together. Hardware is the worst offender. Size, shape, and degree of delicacy changes with nearly every piece. I'm willing to sacrifice a bit of organization for a somewhat efficient manner. What are all your thoughts? What is the best type of tackle or jewelry box to use? Most of them are cheap and flimsy. Is there a better alternative? How can I organize cables to know exactly (within reason) where one is? What about associating cables with hardware (Wall adapter to router, etc.)? What kind of storage unit lends itself to all shapes of hardware? Do I need to separate by size or degree of delicacy for better organization?

  Read the article

• Certain Programs cannot access internet

  - by Cindy

  Operating System: Windows 7 (x64) Problem: Certain Programs are unable to access the internet. They claim that there is no connection when you already are connected. Hello, before we start. Just letting you know I'm new here, and I'm very new to Windows 7. I installed it two days ago. I just installed Windows 7 on my laptop and I have a few problems. I play World of Warcraft, as well as a variety of games. And when I first attempt to log into the game, I get a windows error message, but it doesn't stop there. I thought World of Warcraft got corrupted during the upgrade. It seems that I am unable to access the internet from other online games as well. Most say in along the lines of "Cannot connect to patch server, try again later." I cannot use a downloader Also, I have internet explorer. The x32 version of the browser cannot connect to the internet, and when I try to enter "google.com", it says the same thing. I'm only accessing this site through Internet Explorer x64, which I would have been fine with is it's compatible with Adobe Flash. The only thing that seems to connect to the internet are Internet Explorer x64 and Windows Live Messenger. Here are the steps I have taken, but none worked. 1.) Disable Windows Firewall 2.) Have Windows Firewall Enabled, but allow the specific programs to access internet. And allowed all incoming access. 3.) Disabled UAC, Ran the programs as an admin, and set compatibility to Vista. 4.) Uninstalled an anti-virus program. (McAffee Security Suite 2010) 5.) Reinstalled the programs 6.) Reinstalled Windows 7 7.) Retaken the steps on the Administrator account. Please assist me in this problem. I need to get back into the game. Thanks so much in advance.

  Read the article

• Problems when trying to connect to a router wirelessly

  - by Ruud Lenders

  The situation - At my girlfriend's parents' place there are six Windows 7 devices that are wired or wireless connected to a router: 3 dekstops and 3 laptops. There are also several smartphones using the router. The router is secured with WPA2 (AES). The problem - We never had any problems with the router for over a year. But recently - about 3 weeks ago - my girlfriend's laptop (HP) and my laptop (ASUS) started to develop problems while trying to connect to the router. The router has stopped showing up from the network list. Sometimes it comes back and shows up, but then it keeps saying something along the lines of "Could not connect", and not long after that it dissapears again. The range of the router is not the problem here, because we experience the same when we sit next to the router. Sometimes, if we are lucky, and waited a long time (10-15 minutes) without using the laptop for anything, the laptop will eventually succesful connect to the router. The attempts - Of course, the Window 7 troubleshooter. We tried troubleshooting the connection problems and the wireless network adapter, but no luck. We also reset the router enough times to know that's not helping either. Here's the full list of things we tried, but did not help: Running the Windows 7 troubleshooter Resetting the router (more than once) Setting the router settings to factory defaults Disconnecting all other devices except one laptop Applying a system restore Trying static/dynamic IP/DNS - Dynamic is better, right? Enabling/disabling IPv6 - Should I keep IPv6 disabled? Running the command: netsh wlan stop hostednetwork Running the command: netsh wlan set hostednetwork mode=disallow Updating/reïnstalling wireless adapter drivers The tests - To help finding the core of the problem, we tested the following: Plugging an ethernet cable in the router and in our laptops - worked fine Connecting someone else's laptop to the router (wireless) - worked fine Connecting our laptops to someone else's router - worked fine The router - This information might be relevant: Router model: Sitecom 300N Wireless Router Router hardware: version 01 The DCHP Server's IPs range from 192.168.0.100 to 192.168.0.200. Router settings: Wireless channel: 12 Channel bandwidth: 20/40 MHz Extension channel: 8 Preamble type: Long 802.11g protection: Disabled UPnP: Enabled The laptops - If you are wondering about our laptops: My laptop model: ASUS Pro64JQ Girlfriend's laptop: HP Pavillion G6 OS: Both Windows 7 Professional x64 - with Service Pack 1 My wireless adapter: Atheros AR9285 AdHoc 11n: Enabled The question - Does anyone have experienced the same problems as I do? Or does someone know how to solve this? Are there more tricks I can try, or settings I should change? Note - Our laptops are not slow or old. My laptop is 1.5 years old, and the other laptop is just 5 months old. I know how to keep laptops clean and I'm pretty sure both laptops are not bloated with useless software.

  Read the article

• Write STDOUT & STDERR to a logfile, also write STDERR to screen

  - by Stefan Lasiewski

  I would like to run several commands, and capture all output to a logfile. I also want to print any errors to the screen (or optionally mail the output to someone). Here's an example. The following command will run three commands, and will write all output (STDOUT and STDERR) into a single logfile. { command1 && command2 && command3 ; } > logfile.log 2>&1 Here is what I want to do with the output of these commands: STDERR and STDOUT for all commands goes to a logfile, in case I need it later--- I usually won't look in here unless there are problems. Print STDERR to the screen (or optionally, pipe to /bin/mail), so that any error stands out and doesn't get ignored. It would be nice if the return codes were still usable, so that I could do some error handling. Maybe I want to send email if there was an error, like this: { command1 && command2 && command3 ; } logfile.log 2&1 || mailx -s "There was an error" [email protected] The problem I run into is that STDERR loses context during I/O redirection. A '2&1' will convert STDERR into STDOUT, and therefore I cannot view errors if I do 2 error.log Here are a couple juicier examples. Let's pretend that I am running some familiar build commands, but I don't want the entire build to stop just because of one error so I use the '--keep-going' flag. { ./configure && make --keep-going && make install ; } > build.log 2>&1 Or, here's a simple (And perhaps sloppy) build and deploy script, which will keep going in the event of an error. { ./configure && make --keep-going && make install && rsync -av --keep-going /foo devhost:/foo} > build-and-deploy.log 2>&1 I think what I want involves some sort of Bash I/O Redirection, but I can't figure this out.

  Read the article

• Hour-long shutdown duration "shutting down hyper-v virtual machine management service"

  - by icelava

  I have a Windows 2008 R2 server that is a Hyper-V host (Dell PowerEdge T300). Today for the first time I encountered an odd situation; i lost connection with one of the guest machines but logging on physically it seems the guest OS is still running but no longer contactable via the network. I tried to shut down the guest machine (Windows XP) but it would not shut down, getting stuck in a "Not responding" dialog box that cannot be dismissed. I used the Hyper-V management console to reset the machine and it could not get out of resetting state. I tried to save another Windows 2003 guest machine, and it would be progress with its Saving state (0%). The other running Windows 2003 guest was stuck in the logon dialog. My first suspicion is perhaps one of the Windows update patches this week (10 Nov 2011) may something to do with it, which was still pending a system restart. Well, since I could not do anything with Hyper-V i proceeded with the Windows Update restart, and now it is stuck half an hour at "Shutting down hyper-v virtual machine management service" Prior to restarting I did not observe any hard disk errors reported in the system event log; doubt it is a disk-related condition. Shall I force a hard reboot? UPDATE Ok so i left it hanging over an hour while attending to other matters, and thankfully the host cleanly restarted. I can operate the guest machines fine now. Phew. Hyper-V must have been crawling for some reason. The VMs have been observed to become slow in the past when the host has been up for a long duration (two weeks to a month), but never this slow. Would love to know what types of performance monitoring items i can observe to give a hint why this can happen. UPDATE 2012-02-13 In the months ever since, Hyper-V has stalled into this state another two times. It appears so randomly and without any error event logs to hint what is causing it enter this "drunkard" state. Just an Hyper-V management service timeout. Log Name: System Source: Service Control Manager Date: 13/2/2012 9:16:48 AM Event ID: 7043 Task Category: None Level: Error Keywords: Classic User: N/A Computer: elune Description: The Hyper-V Virtual Machine Management service did not shut down properly after receiving a preshutdown control. Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Service Control Manager" Guid="{555908d1-a6d7-4695-8e1e-26931d2012f4}" EventSourceName="Service Control Manager" /> <EventID Qualifiers="49152">7043</EventID> <Version>0</Version> <Level>2</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x8080000000000000</Keywords> <TimeCreated SystemTime="2012-02-13T01:16:48.882901900Z" /> <EventRecordID>567844</EventRecordID> <Correlation /> <Execution ProcessID="764" ThreadID="8484" /> <Channel>System</Channel> <Computer>elune</Computer> <Security /> </System> <EventData> <Data Name="param1">Hyper-V Virtual Machine Management</Data> </EventData> </Event> The only means out of it is to restart the system.

  Read the article

< Previous Page | 422 423 424 425 426 427 428 429 430 431 432 433  | Next Page >