Search Results

Search found 87957 results on 3519 pages for 'system error'.

Page 427/3519 | < Previous Page | 423 424 425 426 427 428 429 430 431 432 433 434  | Next Page >

  • Kernel panic error

    - by cioby23
    We have a dedicated server with software RAID1 and one of the disk failed recently. The disk was replaced but after rebuilding the array and rebooting the server freezes with a Kernel Panic message No filesystem could mount root, tried: reiserfs ext3 ext2 cramfs msdos vfat iso9660 romfs fuseblk xfs Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(9,1) The filesystem on both disks is ext4. It seems the kernel can't load ext4 support. Is there any way to add ext4 support or do I need to recompile a new kernel again ? Interesting point that before disk replacement all was fine. The kernel is a stock kernel bzImage-2.6.34.6-xxxx-grs-ipv6-64 from our provider OVH Kind regards,

    Read the article

  • Why is the latency on one LVM volume consistently higher?

    - by David Schmitt
    I've got a server with LVM over RAID1. One of the volumes has a consistently higher IO latency (as measured by the diskstats_latency munin plugin) than the other volumes from the same group. As you can see, the dark orange /root volume has consistently high IO latency. Actually ten times the average latency of the physical devices. It also has the highest Min and Max values. My main concern are not the peaks, which occur under high load, but the constant load on (semi-)idle. The server is running Debian Squeeze with the VServer kernel and has four VServer containers and one KVM guest. I'm looking for ways to fix - or at least understand - this situation. Here're some parts of the system configuration: root@kvmhost2:~# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/system--host-root 19G 3.8G 14G 22% / tmpfs 16G 0 16G 0% /lib/init/rw udev 16G 224K 16G 1% /dev tmpfs 16G 0 16G 0% /dev/shm /dev/md0 942M 37M 858M 5% /boot /dev/mapper/system--host-isos 28G 19G 8.1G 70% /srv/isos /dev/mapper/system--host-vs_a 30G 23G 6.0G 79% /var/lib/vservers/a /dev/mapper/system--host-vs_b 5.0G 594M 4.1G 13% /var/lib/vservers/b /dev/mapper/system--host-vs_c 5.0G 555M 4.2G 12% /var/lib/vservers/c /dev/loop0 4.4G 4.4G 0 100% /media/debian-6.0.0-amd64-DVD-1 /dev/loop1 4.4G 4.4G 0 100% /media/debian-6.0.0-i386-DVD-1 /dev/mapper/system--host-vs_d 74G 55G 16G 78% /var/lib/vservers/d root@kvmhost2:~# cat /proc/mounts rootfs / rootfs rw 0 0 none /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0 none /proc proc rw,nosuid,nodev,noexec,relatime 0 0 none /dev devtmpfs rw,relatime,size=16500836k,nr_inodes=4125209,mode=755 0 0 none /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000 0 0 /dev/mapper/system--host-root / ext3 rw,relatime,errors=remount-ro,data=ordered 0 0 tmpfs /lib/init/rw tmpfs rw,nosuid,relatime,mode=755 0 0 tmpfs /dev/shm tmpfs rw,nosuid,nodev,relatime 0 0 fusectl /sys/fs/fuse/connections fusectl rw,relatime 0 0 /dev/md0 /boot ext3 rw,sync,relatime,errors=continue,data=ordered 0 0 /dev/mapper/system--host-isos /srv/isos ext3 rw,relatime,errors=continue,data=ordered 0 0 /dev/mapper/system--host-vs_a /var/lib/vservers/a ext3 rw,relatime,errors=continue,data=ordered 0 0 /dev/mapper/system--host-vs_b /var/lib/vservers/b ext3 rw,relatime,errors=continue,data=ordered 0 0 /dev/mapper/system--host-vs_c /var/lib/vservers/c ext3 rw,relatime,errors=continue,data=ordered 0 0 /dev/loop0 /media/debian-6.0.0-amd64-DVD-1 iso9660 ro,relatime 0 0 /dev/loop1 /media/debian-6.0.0-i386-DVD-1 iso9660 ro,relatime 0 0 /dev/mapper/system--host-vs_d /var/lib/vservers/d ext3 rw,relatime,errors=continue,data=ordered 0 0 root@kvmhost2:~# cat /proc/mdstat Personalities : [raid1] md1 : active raid1 sda2[0] sdb2[1] 975779968 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdb1[1] 979840 blocks [2/2] [UU] unused devices: <none> root@kvmhost2:~# iostat -x Linux 2.6.32-5-vserver-amd64 (kvmhost2) 06/28/2012 _x86_64_ (8 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 3.09 0.14 2.92 1.51 0.00 92.35 Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 23.25 161.12 7.46 37.90 855.27 1596.62 54.05 0.13 2.80 1.76 8.00 sdb 22.82 161.36 7.36 37.66 850.29 1596.62 54.35 0.54 12.01 1.80 8.09 md0 0.00 0.00 0.00 0.00 0.14 0.02 38.44 0.00 0.00 0.00 0.00 md1 0.00 0.00 53.55 198.16 768.01 1585.25 9.35 0.00 0.00 0.00 0.00 dm-0 0.00 0.00 0.48 20.21 16.70 161.71 8.62 0.26 12.72 0.77 1.60 dm-1 0.00 0.00 3.62 10.03 28.94 80.21 8.00 0.19 13.68 1.59 2.17 dm-2 0.00 0.00 0.00 0.00 0.00 0.00 9.17 0.00 9.64 6.42 0.00 dm-3 0.00 0.00 6.73 0.41 53.87 3.28 8.00 0.02 3.44 0.12 0.09 dm-4 0.00 0.00 17.45 18.18 139.57 145.47 8.00 0.42 11.81 0.76 2.69 dm-5 0.00 0.00 2.50 46.38 120.50 371.07 10.06 0.69 14.20 0.46 2.26 dm-6 0.00 0.00 0.02 0.10 0.67 0.81 12.53 0.01 75.53 18.58 0.22 dm-7 0.00 0.00 0.00 0.00 0.00 0.00 7.99 0.00 11.24 9.45 0.00 dm-8 0.00 0.00 22.69 102.76 407.25 822.09 9.80 0.97 7.71 0.39 4.95 dm-9 0.00 0.00 0.06 0.08 0.50 0.62 8.00 0.07 481.23 11.72 0.16 root@kvmhost2:~# ls -l /dev/mapper/ total 0 crw------- 1 root root 10, 59 May 11 11:19 control lrwxrwxrwx 1 root root 7 Jun 5 15:08 system--host-kvm1 -> ../dm-4 lrwxrwxrwx 1 root root 7 Jun 5 15:08 system--host-kvm2 -> ../dm-3 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-isos -> ../dm-2 lrwxrwxrwx 1 root root 7 May 11 11:19 system--host-root -> ../dm-0 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-swap -> ../dm-9 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-vs_d -> ../dm-8 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-vs_b -> ../dm-6 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-vs_c -> ../dm-7 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-vs_a -> ../dm-5 lrwxrwxrwx 1 root root 7 Jun 5 15:08 system--host-kvm3 -> ../dm-1 root@kvmhost2:~#

    Read the article

  • check history of cpu/memory usage in ubuntu?

    - by johnlai2004
    Is there a way for me to review cpu or memory usage on my ubuntu linux server? I've noticed my server (lamp set up) being slow at times, but by the time I log in as root and run a PS command, everything may have returned to normal. It would be great to review a log of what resources different parts of the server consumed.

    Read the article

  • Cobalt Qube 3 Unresponsive

    - by Devin Gund
    I recently bought a used Cobalt Qube 3 server off of eBay. The seller listed it as working before it was shipped. After starting it up for the first time, the "Cobalt Networks" logo scrolled across the LCD screen (this is normal), but then it stayed there. It will not go away, and the server will not respond to any of the buttons besides turning it off. I read the manual, and it does not say anything about this normally occurring. If necessary, could anyone walk me through or provide links to a reset tutorial? I have the OS Restore CD. Please help? I'm not sure why my question is being downvoted but if you need any more information please comment.

    Read the article

  • Legacy VB6 application under Win7 SQL error

    - by Shial
    We have a rather unfortunate legacy application at work, written originally in VB6 it predates anybody in our IT department by at least 5 years. We have a contracted developer for ongoing maintenance and where he can he rewrites sections over into .NET code (Not sure about his techniques here, this is a side job for his regular work as an IBM engineer) the application works fine (such as it is) under windows XP. We have only a couple of Windows 7 machines mainly for testing and this application seems to run into a wall. Things like the background not loading and SQL errors. This is even running under administrator. Running an SQL trace from the ODBC control panel shows several interesting things. It makes a connection to the database successfully initially where it runs a query to determine if it is running the correct version. This query works fine. 558-1af0 ENTER SQLExecDirectW HSTMT 0x020D7548 WCHAR * 0x04C8F0F0 [ 115] "SELECT count(*) c FROM tblSoftwareVersion WHERE fldSoftwareVersion = '123456' AND fldSoftwareName = 'Application.VB'" SDWORD 115 BMS 558-1af0 EXIT SQLExecDirectW with return code 1 (SQL_SUCCESS_WITH_INFO) HSTMT 0x020D7548 WCHAR * 0x04C8F0F0 [ 115] "SELECT count(*) c FROM tblSoftwareVersion WHERE fldSoftwareVersion = '123456' AND fldSoftwareName = 'Application.VB'" SDWORD 115 It then seems to drop its connection and can't find the ODBC connection despite the fact its connecting to the same DB. From the trace it looks like it configures the connection then it starts firing off SQLFreeStmt to unbind and close out then when in the application and it tries to do its thing there is no connection. 558-1af0 ENTER SQLFreeStmt HSTMT 0x020D7548 UWORD 2 <SQL_UNBIND> BMS 558-1af0 EXIT SQLFreeStmt with return code 0 (SQL_SUCCESS) HSTMT 0x020D7548 UWORD 2 <SQL_UNBIND> Then this happens when I try to do something that pulls data 558-1af0 ENTER SQLDriverConnectW HDBC 0x020DDA00 HWND 0x00000000 WCHAR * 0x73EF8634 [ -3] "******\ 0" SWORD -3 WCHAR * 0x73EF8634 SWORD -3 SWORD * 0x00000000 UWORD 0 <SQL_DRIVER_NOPROMPT> BMS 558-1af0 EXIT SQLDriverConnectW with return code -1 (SQL_ERROR) HDBC 0x020DDA00 HWND 0x00000000 WCHAR * 0x73EF8634 [ -3] "******\ 0" SWORD -3 WCHAR * 0x73EF8634 SWORD -3 SWORD * 0x00000000 UWORD 0 <SQL_DRIVER_NOPROMPT> DIAG [IM002] [Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified (0) Nearly all of my searching on this issue comes up with programming issues where the connection string has a problem. The only thing that is different in this particular scenario though is Windows 7, I know the connection string is fine since it works on the XP machines. The VB components are supposed to be still functional under Win7. My computer is running 32 bit win7 and my VP is running Win7 64 bit and both have the same problem so that can be ruled out. I have already tried reinstalling the SQL Native Client and the VB runtime as well as the application in question. Hopefully I can find a solution and not have to resort to using the XP VM.

    Read the article

  • My website is infected, I restored a backup of the uninfected files, how long will it take to un-mark as dangerous?

    - by Cyclone
    My website www.sagamountain.com was recently infected by a malware distributor (or at least I think it may have been). I have removed all external content, google ads, firefly chat, etc. I uploaded a backup from a few weeks ago, when there was no issue. I patched the SQL injection hole. Now, how long will it take to unmark it as dangerous? Where can I contact google? I am not sure if this is the right place to post it, but since it may have been a server issue I may as well. Can sites inject base64 code via a virus on the whole server, or is it only via sql injection? Thanks for the help, viruses freak me out. Is there an online virus scanner that can scan my page and tell me what is wrong?

    Read the article

  • Why is my mono/XSP site loading slow?

    - by acidzombie24
    I have two sites on the same server. One is loading perfectly and incredibly fast. The other is an equally complex site except a bit less javascript and 0 images. Its taking several seconds to load and there is a 1 in 3 chance that i get a Http500 error. WTF I grabbed the lastest 2.6.? version of mono, mod_mono and xsp (libgdiplus-2.6.7, xsp-2.6.5, mod_mono-2.6.3 and mono 2.6.7) This is whats in apache error.log [Mon Jan 03 19:33:40 2011] [error] (70014)End of file found: read_data failed [Mon Jan 03 19:33:40 2011] [error] Command stream corrupted, last command was 1 [Mon Jan 03 19:34:52 2011] [error] (70014)End of file found: read_data failed [Mon Jan 03 19:34:52 2011] [error] (70014)End of file found: read_data failed [Mon Jan 03 19:34:52 2011] [error] Command stream corrupted, last command was 1 [Mon Jan 03 19:34:52 2011] [error] Command stream corrupted, last command was 1 this is the page error Internal Server Error The server encountered an internal error or misconfiguration and was unable to complete your request. Please contact the server administrator, webmaster@localhost and inform them of the time the error occurred, and anything you might have done that may have caused the error. More information about this error may be available in the server error log. Apache/2.2.9 (Debian) PHP/5.2.6-1+lenny9 with Suhosin-Patch mod_mono/2.6.3 Server

    Read the article

  • How to estimate a server specifications for this particular system? [on hold]

    - by Alvaro Fallas
    I'm working in a college project and I'm supposed to specify the server's hardware to hold a system. The system is some kind of social network. And it is supposed to hold around 100 000 users the first year, also the system must be able to handle 1000 users working at the same time. It is the first time I'm asked to do something like this, so I hope you can give me a hand and help me because I feel a little lost. The system's data base is Mysql. I found some server configurations offered by Amazon Web Services, but I don't know which of them is the better for my system due to lack of experience Hope you can help me.

    Read the article

  • Create an alias in Windows XP

    - by Lord Torgamus
    Back in school, I used to have a .login file along the lines of alias ll = ls -l alias dir = ls -Fhl alias web = cd ~/public/public_www/development ... I'd like to do that sort of thing with my XP box here at work, but most of the resources I've found online seem fairly complicated and heavy-duty. Is there a way to do this that doesn't involve mucking about in the registry or running a large batch file? EDIT: My original reason for asking this was that I only need the command line for one command in one specific folder, and I wanted to be able to get to that folder quickly when I launched the command line. But the accepted answer for this question is so good that I decided to ask about my original issue as a separate question here.

    Read the article

  • Dualbooting Win7 and Gentoo, error

    - by Tommy Jakobsen
    Hello I'm trying to setup a dualboot with Gentoo Linux and Windows 7. Heres my partitions: /dev/sda1 /boot partition, ext2 /dev/sda2 win7 partition, ntfs /dev/sda3 swap partition, linux swap /dev/sda4 root partition, btrfs Using Grub, I can boot into Gentoo, but when I'm choosing to boot Windows 7, nothing happens. It just writes the Grub options for that choice, and then it hangs. grub.conf: default 0 timeout 30 title Gentoo root (hd0,0) kernel /boot/kernel-x86_64-2.6.31 root=/dev/sda4 title Windows rootnoverify (hd0,1) makeactive chainloader +1 Any ideas? Help will be much appreciated!

    Read the article

  • Error installing Windows7 64 bits on VirtualBox

    - by MetaDark
    I am trying to set up Windows in Virtual Box, so I don't need to reboot in the rare occasion that I actually need it. The problem is, Virtual Box doesn't preform any errors when I insert the 32bit installation CD but when I try to use the 64bit installation; What!? I am already using the installation disc! I've checked my BIOS to see if I have SVM (AMD's version of VT) disabled and all I see is "Enabled" I have a K9N6PGM2-V2 motherboard A Triple Core AMD Athlon II A Nvdia NForce 430 integrated graphics card 4GB of RAM An 80GB IDE And a 1TB SATA I don't think the last three specifications matter but just in case XP I am pretty sure the CD isn't broken ( I am going to make sure in just a moment ), what could be the cause to this problem? Edit: The 64bit installation CD is not broken, but I found out when trying to install from the 32bit version that it's trying to upgrade, not preform a fresh install - Odd.

    Read the article

  • Microsoft Excel Error

    - by Chris
    I am working with a user that has Office 2007 installed. When they open excel with a blank workbook and then they try to close excel without having done anything, it gets hung for about a minute or two and then gives the warning message: "Microsoft Office Excel is waiting on another application to complete an OLE action." Has anyone ever seen this happen before? If so can you please help me figure out how to resolve this. It doesn't matter what excel file they open or if it is a blank/new workbook. Please Help.

    Read the article

  • Monitoring Dell/HP Servers Running ESXi (Free)

    - by Untalented
    What are you all doing to monitor ESXi servers that run the free edition? With the lack of SNMP support, it seems fairly limited to me. What'd I'd like to be able to do is get some type of alert when a drive or other hardware fails. I've seen a few articles on getting OpenManage installed on an ESXi box (to rebuild an array), but it seems to be quite a pain as well. Even if I get OpenManage working, I won't have alerts without SNMP. Any comments, input, or guidance would be greatly appreciated.

    Read the article

  • IIS7 Binary Stream Error

    - by WDuffy
    I'm struggling to understand the problem I'm seeing so please accept my apology if the question is vague. I'm running a classic asp app in IIS7 and everything seems to work fine except for one issue that has me stumped. Basically, files can be downloaded from the server which is done using the sendBinary method of Persits ASP Upload component. This component works fine for uploading etc it's just the downloading I have a problem. The strange thing is, I cannot have a pure asp page that serves the binary file. Everything works fine in II6, but in II7 there is a strange problem. For example this does not work. <% SET objUpload = server.createObject("Persits.Upload") objUpload.sendBinary "D:\sites\file.pdf", true, "application/octet-binary", true SET objUpload = NOTHING %> However, if I put anything in front of the asp code the file is served fine. serve this <% SET objUpload = server.createObject("Persits.Upload") objUpload.sendBinary "D:\sites\file.pdf", true, "application/octet-binary", true SET objUpload = NOTHING %> I can also write something to the response stream first and it works fine. <% Response.Write("server this") SET objUpload = server.createObject("Persits.Upload") objUpload.sendBinary "D:\sites\file.pdf", true, "application/octet-binary", true SET objUpload = NOTHING %> Does anyone have any ideas of what could be causing this or has anyone ran into a similar situation? I'm sure it has something to do with the setup in IIS 7.

    Read the article

  • Why do "ls" in UNIX and "dir" in DOS have different names?

    - by bizso09
    Why do they have different names for the same command, listing a directory? Surely, they could have talked to each other and agreed on one common name, such as for example cd which is the same for both unix and dos. This decision to have different names has created many headaches for developers and users and also increased incompatibility between the two systems. Did they do it on purpose? Then how come "cd" is the same?

    Read the article

  • How can I allow anonymous access to OTRS FAQ area?

    - by robbie
    I have been searching for this for quite some time now. I am using OTRS 2.4.7 and installed the FAQ package version 1.6.5. Everything seems to work fine. When I am logged in, I can create articles and other users have the ability to browse the articles. I want to be able to allow access to any anonymous non-user to be able to read these articles. Can anyone shed some light on how to allow this type of access? Thanks

    Read the article

  • How to upgrade a single instance's size without downtime

    - by Justin Meltzer
    I'm afraid there may not be a way to do this since we're not load balancing, but I'd like to know if there is any way to upgrade an EC2 EBS backed instance to a larger size without downtime. First of all, we have everything on one instance: both our app and our database (mongodb). This is along the lines i'm thinking: I know you can create snapshots of your EBS and an AMI of your instance. We already have an AMI and we create hourly snapshots. If I spin up a new separate instance of a larger size and then implement (not sure what the right term is here) the snapshots so that our database is up to date, then I could switch the A record of our domain from the old ip address to the new one. However, I'm afraid that after copying over the data from the snapshot, by the time it takes to change the A record and have that change propagate, the data could potentially be stale. Is there a way to prevent this, and is there a better way to do this than I am suggesting?

    Read the article

  • How do I backup my Ubuntu 9.10 system and then restore it to a new machine with different hardware?

    - by EricJLN
    I have a nicely configured Ubuntu 9.10 machine, with crossover linux (from Codeweavers) installed. I have the Nvidia drivers installed. Everything is just as I want it. Now I want to move to a new machine with different hardware: different sized hard drive, different size RAM, different video card, etc. I tried the technique suggested on Ubuntu forums, "Howto: Backup and restore your system!". The results: New system complains about swap not being found New system complains about not finding Nvidia hardware, and I can't open the System-Administration-Hardware Drivers application (i.e., /usr/bin/jockey-gtk) to fix the problem. As result of nvidia, X-Windows is throwing errors, and the on screen process for fixing X-Windows isn't working. How do I restore a backup of my old system, including my Crossover Linux installation, to a new machine with different hardware installed?

    Read the article

  • Importing Outlook 2007 rules error

    - by Alex
    I'm trying to move an Outlook 2007 account (POP3, no Exchange) to a new machine and I'm having trouble importing the rules from the old machine to the new one. Here is the deal, I imported the .pst file on the new machine but when I try to import the rules, every single one of them brakes. The folders and sub-folders hierarchy is preserved upon the import of the .pst but the rules don't point to the right folder in the respective rule. Instead it points to "the specified folder". Same OS (Windows XP), same mail client (Outlook 2007) and the .psf file is about 8 GB. Any help i greatly appreciated.

    Read the article

  • NGINX - CORS error affecting only Firefox

    - by wiherek
    this is an issue with Nginx that affects only firefox. I have this config: http://pastebin.com/q6Yeqxv9 upstream connect { server 127.0.0.1:8080; } server { server_name admin.example.com www.admin.example.com; listen 80; return 301 https://admin.example.com$request_uri; } server { listen 80; server_name ankieta.example.com www.ankieta.example.com; add_header Access-Control-Allow-Origin $http_origin; add_header 'Access-Control-Allow-Methods' 'GET, POST, OPTIONS, PUT, PATCH, DELETE'; add_header 'Access-Control-Allow-Credentials' 'true'; add_header 'Access-Control-Allow-Headers' 'Access-Control-Request-Method,Access-Control-Request-Headers,Cache,Pragma,Authorization,Accept,Accept-Encoding,Accept-Language,Host,Referer,Content-Length,Origin,DNT,X-Mx-ReqToken,Keep-Alive,User-Agent,X-Requested-With,If-Modified-Since,Cache-Control,Content-Type'; return 301 https://ankieta.example.com$request_uri; } server { server_name admin.example.com; listen 443 ssl; ssl_certificate /srv/ssl/14182263.pem; ssl_certificate_key /srv/ssl/admin_i_ankieta.example.com.key; ssl_protocols SSLv3 TLSv1; ssl_ciphers ALL:!aNULL:!ADH:!eNULL:!LOW:!EXP:RC4+RSA:+HIGH:+MEDIUM; location / { proxy_pass http://connect; } } server { server_name ankieta.example.com; listen 443 ssl; ssl_certificate /srv/ssl/14182263.pem; ssl_certificate_key /srv/ssl/admin_i_ankieta.example.com.key; ssl_protocols SSLv3 TLSv1; ssl_ciphers ALL:!aNULL:!ADH:!eNULL:!LOW:!EXP:RC4+RSA:+HIGH:+MEDIUM; root /srv/limesurvey; index index.php; add_header 'Access-Control-Allow-Origin' $http_origin; add_header 'Access-Control-Allow-Methods' 'GET, POST, OPTIONS, PUT, PATCH, DELETE'; add_header 'Access-Control-Allow-Credentials' 'true'; add_header 'Access-Control-Allow-Headers' 'Access-Control-Request-Method,Access-Control-Request-Headers,Cache,Pragma,Authorization,Accept,Accept-Encoding,Accept-Language,Host,Referer,Content-Length,Origin,DNT,X-Mx-ReqToken,Keep-Alive,User-Agent,X-Requested-With,If-Modified-Since,Cache-Control,Content-Type'; client_max_body_size 4M; location / { try_files $uri $uri/ /index.php?q=$uri&$args; } location ~ /*.php$ { fastcgi_split_path_info ^(.+\.php)(/.+)$; #NOTE: You should have "cgi.fix_pathinfo = 0;" in php.ini include fastcgi_params; fastcgi_param SCRIPT_FILENAME /srv/limesurvey$fastcgi_script_name; # fastcgi_param HTTPS $https; fastcgi_intercept_errors on; fastcgi_pass 127.0.0.1:9000; } location ~* \.(js|css|png|jpg|jpeg|gif|ico)$ { expires max; log_not_found off; } } this is basically an AngularJS app and a PHP app (LimeSurvey), served under two different domains by the same webserver (Nginx). AngularJS is in fact served by ConnectJS, which is proxied to by Nginx (ConnectJS listens only on localhost). In Firefox console I get this: Cross-Origin Request Blocked: The Same Origin Policy disallows reading the remote resource at https://ankieta.example.com/admin/remotecontrol. This can be fixed by moving the resource to the same domain or enabling CORS. which of course is annoying. Other browsers work fine (Chrome, IE). Any suggestions on this?

    Read the article

  • Conection refused error for telnet and ssh

    - by pnp
    I try to telnet to one of my systems 172.16.xx.z from 172.16.xx.y, but the response i get is- sudo telnet 172.16.xx.z Trying 172.16.xx.z... telnet: Unable to connect to remote host: Connection refused Same for localhost- sudo telnet localhost Trying ::1... Trying 127.0.0.1... telnet: Unable to connect to remote host: Connection refused And the same experience with ssh: sudo ssh 172.16.xx.z ssh: connect to host 172.16.xx.z port 22: Connection refused Any guesses what could be wrong here? Both my systems run on Ubuntu.

    Read the article

  • Decrypting EFS w/o altering timestamp - possible?

    - by grojo
    Hi, I'd like to decrypt some EFS-encrypted files, but I do not know how to do that without altering the timestamp. When encrypting/decrypting files, the modified-time is set to the current time. I'd like to preserve the original timestamp, as the files have not really changed. Is this possible? Solutions i dont think work copy to/from FAT (timestamp resolution differs) copy to from Samba share (same) programmatically copy original timestamp and reapply after decryption (possible, but need to handle decryption time which may vary)

    Read the article

  • CVS gives error files fail to update, but they are updated on the server

    - by Alvin Sim
    We are using CVSNT on machine running Windows XP Pro. After using it for more than 5 years, today we have an issue with CVS. When we try to update a subdirectory in a repository, some of the files failed to update with message "Permission denied" and some files fail with the message "ABC.java is no longer in the repository". But when we login to the CVS machine itself and browse the subdirectory, we can see the files are there. We have checked the Windows folder permissions and they seem correct.

    Read the article

  • When a server gets rooted, should I disconnect network or power?

    - by Aleksandr Levchuk
    When a server gets rooted (e.g. a situation like this), one of the first things that should be done is containment. Quoting from Robert Moir's Answer: "disconnect the victim from its muggers" A server can be contained by pulling the network cable or the power cable. Taking into consideration the need for: Protecting victims from further damage Executing successful forensics (Possibly) Protecting valuable data on the server Which method is better?

    Read the article

< Previous Page | 423 424 425 426 427 428 429 430 431 432 433 434  | Next Page >