Search Results

Search found 12497 results on 500 pages for 'linked servers'.

Page 428/500 | < Previous Page | 424 425 426 427 428 429 430 431 432 433 434 435  | Next Page >

  • How to prevent asymmetric routing with multiple eBGP routers?

    - by Andy Shinn
    I have 2 routers announcing a /22 subnet to different providers (one providers connects to each of the 2 routers). I have split the /22 in two /23 to announce one /23 on each of the routers plus the /22 (the providers will take the more specific route). This allows me to fail over and keep traffic inside the /23 in and out the same provider. What are other ways in which I could announce just the /22 with both routers and have packets from servers on the network behind the routers go back out the same router in which they came in from? EDIT: The main problem I come across, which end users and clients complain about the most, is that the least hop route is sometimes not the "optimal" route. In my case, I know that Provider B may have better latency to X nation. But when packets come in from provider B, they may go out Provider A or provider B. The reverse is also true. If I send a packet to X nation out provider A, even though it may have more hops back, the packet will likely come in from Provider B (which may have higher latency, packet loss, etc. to this nation)

    Read the article

  • MySQL slave server from dumps

    - by HTF
    I've created a slave server from live machine which is acting as a master now. I use the following procedure to create it: mysqldump --opt -Q -B --master-data=2 --all-databases > dump.sql then I imported this dump on the new machine, applied the "CHANGE MASTER TO..." directive with a log file/position from the dump. Please note that I have around 8000 databases and I didn't stop the master while the dumps were running. The replication works fine but is this a properly method for creating a slave server? I'm planning to promote this slave to a master (different location) so I would like to make sure that there is a 100% data consistency between the servers. I've found this article where it says: The naive approach is just to use mysqldump to export a copy of the master and load it on the slave server. This works if you only have one database. With multiple database, you'll end up with inconsistent data. Mysqldump will dump data from each database on the server in a different transaction. That means that your export will have data from a different point in time for each database. Thank you

    Read the article

  • Switch to IPv6 and get rid of NAT? Are you kidding?

    - by Ernie
    So our ISP has set up IPv6 recently, and I've been studying what the transition should entail before jumping into the fray. I've noticed three very important issues: Our office NAT router (an old Linksys BEFSR41) does not support IPv6. Nor does any newer router, AFAICT. The book I'm reading about IPv6 tells me that it makes NAT "unnecessary" anyway. If we're supposed to just get rid of this router and plug everything directly to the Internet, I start to panic. There's no way in hell I'll put our billing database (With lots of credit card information!) on the internet for everyone to see. Even if I were to propose setting up Windows' firewall on it to allow only 6 addresses to have any access to it at all, I still break out in a cold sweat. I don't trust Windows, Windows' firewall, or the network at large enough to even be remotely comfortable with that. There's a few old hardware devices (ie, printers) that have absolutely no IPv6 capability at all. And likely a laundry list of security issues that date back to around 1998. And likely no way to actually patch them in any way. And no funding for new printers. I hear that IPv6 and IPSEC are supposed to make all this secure somehow, but without physically separated networks that make these devices invisible to the Internet, I really can't see how. I can likewise really see how any defences I create will be overrun in short order. I've been running servers on the Internet for years now and I'm quite familiar with the sort of things necessary to secure those, but putting something Private on the network like our billing database has always been completely out of the question. What should I be replacing NAT with, if we don't have physically separate networks?

    Read the article

  • How to avoid sshfs freezing?

    - by Andreas Hagen
    So the issue is this: I've installed sshfs on Ubuntu 12.04 and I'm trying to connect to a couple of remote servers. So initially the mount seams successful. Sometimes Gnome even picks it up and displays the "new device found" box at the bottom of the screen. but from here on there is not much that works. Or at least not any more. The first couple of times i connected it seamed to work fine, and I was able to transfer some files, then i disconnected using fusermount -u <folder> and after reconnecting a little later the trouble started. Now after executing sshfs -o ServerAliveInterval=15 -o reconnect -C -o workaround=all -o idmap=user root@<host>:/ <folder>, when I change directory into the mount-point, the shell just freezes. Strangely ls -al <folder> works when listing just the root of the remote system, but nothing more. Also every file-explorer I've tried freezes just like cd <folder>. To me it seamed like there was some kind of zombie thread or something hanging around my system, due to the fact that it did work the first time, so I have tried rebooting but no luck. sshfs -V gives this: SSHFS version 2.3 FUSE library version: 2.8.6 fusermount version: 2.8.6 using FUSE kernel interface version 7.12 So yea, any ideas?

    Read the article

  • How to Deploy an ASP.NET Web API- and Browser-based Application to a Production Environment [closed]

    - by lmttag
    Possible Duplicate: How to Deploy an ASP.NET Web API- and Browser-based Application to a Production Environment We have an ASP.NET Web API server that serves up a SQL Server data driven website. The API uses JSON to transfer data from SQL Server to the front end. We need to move it to an internal production environment (nothing will be exposed on the public Internet) and we’re having problems - or just not understanding what needs to be done. There are two domains: The corporate domain - where all users login normally. The process domain - contains the database the Web API needs to access. The IT staff wants to put a DMZ between the two domains to house the IIS app and shield the users on the corporate domain from having access into the process domain directly. The ideal configuration is: corp domain (end users) <–> firewall (open port 80) <–> DMZ (web server running IIS) <–> firewall (open port 80 or 1433????) <–> process domain (IIS for Web API and SQL Server) We don’t really understand how to deploy our browser/Web API application in this scenario. Do we need to break up our application so that all the client code is on the IIS server in the DMZ, while the Web API gets installed on the server in the process domain? Does the entire app (client code and Web API) stay together on the IIS server in the DMZ, which then somehow accesses the SQL Server instance to get data? From the IIS server and app in the DMZ, would you simply access the Web API on the server in the process domain by going to http://server/appname/api/getitmes? In the second firewall between the DMZ and the process domain, would you have to open port 1433 or just port 80 since the Web API is a HTTP endpoint? Or, is there some better way of deployment (i.e., how ASP.NET Web API single page applications written all in HTML5 and JavaScript supposed to be deployed to production environments?)? NB: The servers are Win2k8 R2, SQL Server 2k8 R2, and IIS 7.5.

    Read the article

  • How can I avoid permission denied errors when attempting to deploy a rails app with capistrano?

    - by joshee
    Total noob here. I'm attempting to deploy an app through Capistrano. I'm getting relentless permission denied errors when I attempt to run cap deploy:update. Seemingly at least some of these errors are due to missing directories that trigger a "Permission Denied" error. (I'm doing setup on root just temporarily.) set :user, 'root' set :domain, 'domainname.com' set :application, 'appname' # adjust if you are using RVM, remove if you are not $:.unshift(File.expand_path('./lib', ENV['rvm_path'])) require "rvm/capistrano" set :rvm_ruby_string, '1.9.2' # file paths set :repository, "ssh://[email protected]/~/git/appname.git" set :deploy_to, "/var/rails/appname" # distribute your applications across servers (the instructions below put them # all on the same server, defined above as 'domain', adjust as necessary) role :app, domain role :web, domain role :db, domain, :primary => true set :deploy_via, :remote_cache set :scm, 'git' set :branch, 'master' set :scm_verbose, true set :use_sudo, false set :rails_env, :production namespace :deploy do desc "cause Passenger to initiate a restart" task :restart do run "touch #{current_path}/tmp/restart.txt" end desc "reload the database with seed data" task :seed do run "cd #{current_path}; rake db:seed RAILS_ENV=#{rails_env}" end end after "deploy:update_code", :bundle_install desc "install the necessary prerequisites" task :bundle_install, :roles => :app do run "cd #{release_path} && bundle install" end Here's my result: ** [domainname.com :: out] Cloning into '/var/rails/appname/shared/cached-copy'... ** [domainname.com :: err] Permission denied, please try again. ** [domainname.com :: err] Permission denied, please try again. ** [domainname.com :: err] Permission denied (publickey,gssapi-with-mic,password). ** [domainname.com :: err] fatal: The remote end hung up unexpectedly I'm able to ssh without a password, so not sure about that publickey error. By the way, if I run cap deploy:update without set :deploy_via, :remote_cache, here's my result: ** [domainname.com :: out] Cloning into '/var/rails/appname/releases/20120326204237'... ** [domainname.com :: err] Permission denied, please try again. ** [domainname.com :: err] Permission denied, please try again. ** [domainname.com :: err] Permission denied (publickey,gssapi-with-mic,password). ** [domainname.com :: err] fatal: The remote end hung up unexpectedly command finished Thanks a lot for your help with this.

    Read the article

  • Nagios send mail when server is down

    - by tzulberti
    I am using nagios 3.06 to monitor the servers. When a service is critical, it sends a mail, but when a server is down no mail is sent. Even if all the services go to critical state, no mail is sent. I have the following configuration: define command {     command_name notify-host-by-email     command_line python /etc/nagios3/send_mail.py "[Nagios] $HOSTNAME$" "******** Nagios ****\n\n Host: $HOSTNAME$\n Description: the server is down" } define command{     command_name notify-service-by-email     command_line python /etc/nagios3/send_mail.py "[Nagios] $HOSTNAME$: $SERVICEDESC$ ($NOTIFICATIONTYPE$)" "***** Nagios *****\n\nNotification Type: $NOTIFICATIONTYPE$\nService: $SERVICEDESC$\nHost: $HOSTALIAS$\nAddress: $HOSTADDRESS$\nState: $SERVICESTATE$\nDate/Time: $LONGDATETIME$\nAdditional Info:$SERVICEOUTPUT$" } The python script is a script to sent a mail. It works if I execute it from the command line, but it doesn't sents an email from nagios. What I am doing wrong? UPDATE: The contact data is: define contact{     contact_name root     alias Root     service_notification_period 24x7     host_notification_period 24x7     service_notification_options w,u,c,r     host_notification_options d,r     service_notification_commands notify-service-by-email     host_notification_commands notify-host-by-email     email [email protected] } define contactgroup{     contactgroup_name admins     alias Nagios Administrators     members root }

    Read the article

  • Load is 0, yet site crawls (sometimes). What gives?

    - by Yegor
    I have a ~1.5-2mil page views per day site running on 2 servers. One for mysql, other for everything else. Mysql box has a load of 3, frontend is usually 0.0-0.1. Both are dual quad core with 8GB ram running SAS drives in raid5. CPU is idle for majority of the time, iowait is non-existent. Im running nginx, memcache, and site is built on php. Half the time everything runs perfect, while at other times it lags something severe, when it takes 10-15 seconds for a page to load. Page execution time is always super low, but it seems to hang, waiting for something before it actually loads the page. Whats even more weird is that it only happens to 1 file on the site (but its the one thats most commonly accessed, that actually loads the content on the site). Other pages are super fast at all times, even when it takes 15 seconds to load actual content. I have nginx_stats plugin installed, and if I monitor it, the lag spikes happen when the write column starts going above 100, and it frequently does... all the way to 500-1000. It does so at totally random times... not when traffic is heavy... it can do this in the middle of the night, and work perfectly at 5pm when traffic is at its highest. Any ideas?

    Read the article

  • Technology mash: is this possible?

    - by Jon Story
    I'm in the process of setting up my own DNS+hosting on a couple of VPS and my home machines, mostly for academic/learning purposes, but also for convenient accessing of my files, hosting my personal websites, private git repositories etc. I've got a main web server with DNS, and a slave DNS server. I've also got a couple of machines at home doing file hosting, video streaming and all that fun stuff. I'm intending to use my VPS's to provide myself with a dynamic DNS system so that I can point mydomain.com at my DNS servers, with home.mydomain.com going into my home network via a raspberry pi. HOWEVER.... I've not got access to the network infrastructure at home (rented accommodation with managed internet), so I can't forward the ports on the router to my own machines. As such, I'm wondering if it's possible to route all the traffic via an SSH/HTTP tunnel through one of the VPS? My plan is to have the raspberry pi provide a VPN into my home network. The raspberry pi uses SSH to connect to the VPS, and the VPS forwards any traffic to home.mydomain.com via the tunnel to the raspberry pi. Is this even possible, and how do I go about it? I don't mind getting my hands dirty with coding and low level tools, I'm just not sure where to start or what the best way to go about it is.

    Read the article

  • "one-off" use of http_proxy in a Chef remote_file resource

    - by user169200
    I have a use case where most of my remote_file resources and yum resources download files directly from an internal server. However, there is a need to download one or two files with remote_file that is outside our firewall and which must go through a HTTP proxy. If I set the http_proxy setting in /etc/chef/client.rb, it adversely affects the recipe's ability to download yum and other files from internal resources. Is there a way to have a remote_file resource download a remote URL through a proxy without setting the http_proxy value in /etc/chef/client.rb? In my sample code, below, I'm downloading a redmine bundle from rubyforge.org, which requires my servers to go through a corporate proxy. I came up with a ruby_block before and after the remote_file resource that sets the http_proxy and "unsets" it. I'm looking for a cleaner way to do this. ruby_block "setenv-http_proxy" do block do Chef::Config.http_proxy = node['redmine']['http_proxy'] ENV['http_proxy'] = node['redmine']['http_proxy'] ENV['HTTP_PROXY'] = node['redmine']['http_proxy'] end action node['redmine']['rubyforge_use_proxy'] ? :create : :nothing notifies :create_if_missing, "remote_file[redmine-bundle.zip]", :immediately end remote_file "redmine-bundle.zip" do path "#{Dir.tmpdir}/redmine-#{attrs['version']}-bundle.zip" source attrs['download_url'] mode "0644" action :create_if_missing notifies :decompress, "zipp[redmine-bundle.zip]", :immediately notifies :create, "ruby_block[unsetenv-http_proxy]", :immediately end ruby_block "unsetenv-http_proxy" do block do Chef::Config.http_proxy = nil ENV['http_proxy'] = nil ENV['HTTP_PROXY'] = nil end action node['redmine']['rubyforge_use_proxy'] ? :create : :nothing end

    Read the article

  • Create account for service

    - by Andy
    I am configuring a new server. The server is running Hudson that is going to copy some files from this server to another. The other server is a virtual machine. Both running Windows Server 2012. Hudson is started on server A with log on as "Local System". When I come to the copy phase it says "Access denied". Changing the log on to "Administrator" works. However, I guess this is bad. I do not have much experience with user management. I tried to create a own hudson account on both servers A and B. I tried to log on as hudson account in the service-management but it doesn't start. How would you create an account for this particular service that has access to the shared folder on server B and can be used to start the service on server A? I guess I need two accounts with same username and password on server A and server B? The folder on Server B is shared with everyone and the guest account is enabled.

    Read the article

  • Accessing a shared folder in Windows Server 2008 R2.

    - by Triztian
    Hello all, seems my involvement with computers has grown and I've found my self in the need to access a shared folder on a server. I've read some documentation and managed to set up the folder as a share, for this I created a local group and for now just one local user that has access to the share, the folder is in the public user folder and it's permissions should be (and I believe they are) read/write. The problem is that I can't connect from a remote machine I mean I don't know how the way it should be accessed, the server has a public IP and we use it also as a host to our website I don't know if that affects it though, the folder will be used as the "keeper" for the QuickBooks company files and has the database server manager installed. I've tried setting up a VPN Connection to the but no success. The server has a domain name a "http://www.example.com" that redirects to our website, I am unsure if it could be accessed that way, also the share has a location displayed when I right-click properties Heres what I've tried Setting up a VPN Connection (Windows Vista and 7) Got to the point where I got asked for credential and entered the user I created (which is not an admin) but I got a "Connection fail error 800" I suppose this is because in the domain field I entered the servers workgroup. right-click add network connection (Windows 7) Went through the wizard until I reached the point of entering the location, tried many things, the name in the share's properties(\\SOMETHING\Share), the http://www.example.com , the IP address I'm quite unfamiliar with this, so I have my guesses: Since the group and user are local they do not have access to the folder. The firewall in the server is blocking my connection. Anyways, any help and guidence is truly appreciated.

    Read the article

  • virtualized windows 2003 domain with CentOS 5.3 and poor connectivity

    - by Chris Gow
    Hi: I have a test lab set up running a virtualized windows 2003 domain on a CentOS 5.3(xen) host and am experiencing connectivity problems with guests running on other hosts that are part of the same domain. Here's the setup: On Computer A I have CentOS 5.3 running as the host and have virtualized windows 2003 servers for a primary domain controller, a backup domain controller and an exchange server. The primary domain controller also acts as a WINS and dns server. The windows domain appears on a separate subnet from my company's corporate network. Connectivity to any of the virtualized guests on Computer A is fine (remote desktop, ping, what have you). I have another host computer (Computer B) that also has a virtualized Windows 2003 server guest that is part of the same domain. However, connectivity to that guest is flaky at best. I continuously get at least 60% packet loss when I try to ping the guest, and due to that flakiness I can not access any of the services that it runs (remote desktop, web). Now here's the interesting part. It seems to affect only machines running on a different computer than the domain controller that are in the same domain. On Computer B there is another Windows 2003 guest that is not part of the test domain and is on my corporate network. There's no connectivity issues with that guest machine. The problem does not seem to be specific to Computer B either. I created a test VM on my local computer within the test domain and it exhibits the same behaviour as the guest in Computer B. A couple of items to note: - Host OS on both Computer A and B are the same CentOS 5.3 64 bit - Guest OS is Windows 2003 64 bit and 32 bit (the guest on Computer B is 32 bit) - Guest OSes are all up to date (as of Monday) - Host OS on Computer A was upgraded from CentOS 5.2 to 5.3 Update: Sorry I did not follow up with the comments from below. Computer A and B have been moved to their own dedicated switch and the problem has gone away. I'm not sure what the underlying problem(s) were though

    Read the article

  • VMWare web UI intermittent access on CentOS

    - by PeteWilliams
    Hiya, I've got a CentOS 5.2 server that I'm trying to get set up as a development environment. As part of this, I planned to install VMWare Server 2 and set up several virtual development servers. I've got as far as installing VMWare Server 2 but access to the remote control panel is only working intermittently. If I access it through Firefox at https://127.0.0.1:8333/ui/# it usually says either: "Connection intterupted: connection was reset before the page loaded" Or "Firefox can't establish a connection to the server at 127.0.0.1" But every now and then it lets me in and I'll manage a few clicks in the web UI before it kicks me out with the following error: "The server could not complete a request (HTTP 0 ). The server encountered an unexpected condition that prevented it from fulfilling the request. If this problem persists, please contact your system administrator." I've done all the updates available in CentOS except one OpenOffice one that is causing a conflict, and I re-ran wmware-config.pl after updating the kernel. Though I went with all the defaults as I don't really know what I'm doing! I've since rebooted and nothing changed. I've also tried accessing the control panel remotely from another machine in the network and the results are the same. Does anyone have any ideas what might be causing this and how I can resolve it? I'm afraid I'm a developer playing at sys-admin, so I may be missing something obvious! Many thanks Pete Update I have now reinstalled both the operating system and VMWare and I'm still getting the same issue. I wonder if it's a result of the settings I'm putting in on the config.pl script..?

    Read the article

  • vSphere - datastore falling off a host

    - by Chadddada
    Recently we have been running the vCheck powershell script daily in order to help in monitoring our vSphere ESX 4.0 environment. One of the oddities that we have been seeing is that some of the datastores on the SAN don't always show up on every host. Our hosts are connected redundantly, via FC, to some brocade FC switches, which then connect via fiber to our EMC Ax4 SAN. While all the datastores are presented to each host we have, and they see them initially, they sometimes seem to fall off and are no longer visible. It easy enough to rescan for datastores and add them back to the hosts the hosts but this seems to be an error. Has anyone else seen this or know why it may be happening? Responses to questions: 1. Is it always the same ESX servers that lose their connection? – Scott Warren No this happens randomly on random hosts. If a VM is running on a particular host, of which the VM's disks are on a SAN datastore, then that datastore won't disappear. It seems to happen if a host doesn't touch a datastore for a bit and it just forgets about it.

    Read the article

  • Three server processes consume no more than 50% of Dual Core CPU

    - by thor
    I have three processes running on Intel Core 2 Duo CPU. From watching output of 'top' and graphs of CPU load (drawn by MRTG, data collection via SNMP) I can see that CPU load is never more than 50%, and, most of the day, when those processes are busy CPU load has a ceiling at 50 %. I mean, CPU load grows up to 50% in the morning and stays there until late evening. My first thought was that only one core was used at 100% thus giving 50% of both CPUs. But, as there are three processes running and from 'top' I see that both cores are being loaded, so this is not the case. schedtool shows that CPU affinity for those three processes is at default, 0x03, allowing them to use both cores. If I force one process to one core (schedtool -a 0x01), and two others to second (schedtool -a 0x02), cumulative usage grows beyond 50%. Why three processes seem to consume only 50% of two cores? Why forcing them to different CPUs allows usage to grow higher? Any hints? P.S. Processes in question are Counter-Strike servers.

    Read the article

  • How to setup port forwarding from my Webserver (apache) to my Database server (mysql)

    - by karman888
    Hello again guys, and thank you for your help so far. Here is my problem: I have two remote dedicated servers, one webserver that runs apache, and one db server that runs mysql. The apache server is visible on the internet of course, but the second server is only visible to the apache server because they are connected with LAN. I need to connect to the remote mysql server through internet from my home-pc , but only apache server is visible to my home-pc. How can i setup port-forwarding from my apache server to the mysql server so i will be able to "see" the mysql server from my home-pc? This question is a follow-up from my first question Connect to remote mysql server from my application. Problem is that Mysql server is on LAN in which you answered me and helped me a lot by telling me to do "port-forwarding". I looked over the internet, and i cant find a good how-to to do port-forwarding. I'm an experienced programmer, but have little experience on hardware and networks. I can understand though what must be done, so i just need a litle help to sort things out :) I hope you can help me guys, Thank you in advance p.s. machine that Apache is running is on CentOS, mysql server also CentOS. p.s2 webserver runs WebHostManager i dont know if that makes any difference or it can be made easily through this, i just mention it :)

    Read the article

  • CentOS: Init scripts failing to start for some unknown reason

    - by user705142
    I'm running CentOS 6.2 - I've just migrated some applications over to a failover server, and copied their init scripts into /etc/init.d. I've made them executable, added them to chkconfig, with chkconfig -add, set their levels, made sure they're residing in /etc/rc.d/ - made sure I can execute them from rc2.d etc. The permissions are the same on both servers. They're also running in the same order as on the primary server Yet on reboot they don't start. Any ideas? The offenders are these: jetty 0:off 1:off 2:on 3:on 4:on 5:on 6:off smart 0:off 1:off 2:on 3:on 4:on 5:on 6:off /etc/init.d: -rwxr-xr-x. 1 root root 14456 Mar 13 20:21 jetty -rwxrwxrwx. 1 root root 5829 Mar 29 09:58 smart /etc/rc.d/rc3.d lrwxrwxrwx. 1 root root 15 Mar 29 19:21 S99jetty -> ../init.d/jetty lrwxrwxrwx. 1 root root 11 Mar 26 17:12 S99local -> ../rc.local lrwxrwxrwx. 1 root root 15 Mar 29 19:21 S99smart -> ../init.d/smart I've checked, and I'm in run level 3. I've checked their logs, and there's no indication that that they've been started. I can start them manually easily - and other services are starting normally. I'm completely out of ideas really.

    Read the article

  • Terminal emulation has stopped working. Garbage escape chars

    - by oligofren
    To enable me to do some remote administration of our servers I started using a terminal emulation program called TouchTerm Pro on my iPhone. While not the smoothest experience, it has allowed me to leave my computer behind when going out of town, which makes the slightly painful experience worthwhile. As of late, the app unfortunately no longer works. Pressing up and down keys after logging on via ssh gives me garbage like ^[[A and ^[[B. Combinations with Ctrl - like you can see in the video - no longer works either. Writing full command lines and executing by the enter key works though. Being able to search my bash history was the difference between a usable app and endless frustration, so getting it to work is essential. The app has (of course) met its end of life, not getting updated anymore. I am not quite sure, which side (client or server) that has to be "fixed"/hacked to make the control sequences work again. But is there something I can do to make it work as intended? You can see a video of TouchTerm in operation here.

    Read the article

  • Virtualize SBS 2003 - P2V vs migrating to new VM

    - by jlehtinen
    I need to virtualize a SBS 2003 server in my work environment. I need some tips on what people think is the best way to proceed. Background: The SBS 2003 server is the primary DC for the domain and also hosts FTP, RRAS(VPN), DNS, and file shares. Exchange is NOT used, neither is SQL server. DHCP is done via a firewall appliance. I have added a Server 2003 VM to the domain and promoted it to the DC role. AD/DNS is replicating here correctly. This was mainly done to provide fault-tolerance to the domain, I was not intending to make this VM the primary DC. I've already asked about buying upgraded licensing for Server 2008/2012 but was refused due to cost. Options: I see (at least) two routes I could take to complete this. From what I've read option 2 is the "preferred" method, but there's a few steps where I'm not clear on what to expect. Option 1.) P2V the primary DC Power off primary DC Power off secondary DC (to prevent USN rollback in case P2V has issue) P2V (cold clone) primary DC Boot new PDC VM Allow new hardware to detect Remove old NIC hardware from device manager Assign old IPs to new virtual NICs Reboot PDC VM, confirm connectivity and no major issues Power on secondary DC, confirm replication Option 2.) Create new VM, transfer roles, remove original DC from domain Create new VM, install SBS 2003 Do I need the original SBS install discs for this? MS migration doc mentions this. Add VM to domain, promote to DC role Does this start 7 day timer where two SBS servers can be in same domain? Set up RRAS on new VM Set up IIS/FTP on new VM Move file shares to new VM Transfer FSMO roles to new VM DC dcpromo original primary DC out of domain

    Read the article

  • Converting a Windows 2003 server

    - by Jim Bass
    We have a legacy database system based upon MS SQL running on Windows Server 2003. The client software will only run on Windows XP. We have recently had success converting a client into a virtual machine and running it under Fusion on Mac minis. So far, it is working incredibly well. So well, in fact, that we are now considering trying to convert the server to a virtual machine. This raises several questions, though: 1. The server uses a raid array. Does the VM virtualize the raid array? I only ask because in my experience Windows products don't like it when you change core hardware. 2. Is there any reason why running SQL server on a virtual machine won't work? It will be up 24/7. 3. Is there a different converter for servers? 4. Will I have to track down the licensing for MS SQL and Server 2003 or will they come across ok? 5. The company that designed the software is no longer in business. There is some fear that the software is somehow tied to the hardware configuration. We bought the hardware, but their engineers came out and configured the system. Will the virtual machine be able to spoof particular chip sets? Thanks! Jim Bass

    Read the article

  • HP/Lenovo alternative to Buffalo iSCSI TerraStation?

    - by Robin Day
    I'm looking at virtualising some of our infrastructure in order to allow for more resiliance and future expandability. We have successfully virtualised on single servers with Direct Attached Storage and are now looking for a more future proof solution using a high powered host (or two) and a SAN (or two). I'm thinking that the host machine will probably be an HP ProLiant DL360 G7 (all of our exisiting infrastructure is HP). Unfortunately, I am new to the world of SANs. From what I can see, the Buffalo Terrastation III is all I would need in order to setup an iSCSI SAN for VMWare to use. However, I'm a little reticent to go that way as it's a bit too "entry level" for my liking. In particular I would be very keen for more redundancy, power, networking, etc. I'm also very aware that you "get what you pay for". Therefore, can anyone reccommend equivalents from the big boys? HP/Lenovo? I have searched high and low on the HP site and seen many options but am struggling to work out if it is all the hardware I will need. Some options appear to need separate controllers from disk enclosures, etc.

    Read the article

  • VCL - configuration for Magento and Varnish 3.0.2

    - by Tomas
    I would like to kindly ask if there's someone who can help me configure Varnish for Magento to reach far more hits. My current ratio from varnishstat is: cache_hit=271 cache_miss=926 I'm kindly asking this because I've googled almost every site related to this theme, but 99.9% of configurations don't work because of outdated code. Details of my set-up: I use Varnish on port 80, Apache on port 81, PageCache as Magento varnish module, APC for PHP speed and Memcached for dynamic caching. Load speed is about 1.5s on home-page (Pingdom.com average results) USA ping & 2.5s Europe. Servers are located in Toronto, Canada. EDIT: This is my full VCL configuration http://pastebin.com/885BzHCs (I just use xxx.xxx.xxx.xxx for my IPs) This is the info from the command (varnishtop -i TxHeader -I Cookie): TxHeader Cookie: frontend=965b5...(*lots of numbers); adminhtml=3ae65...(*lots of numbers); EXTERNAL_NO_CACHE=1 "(*lots of numbers)" is just my adding to the info Any idea how to avoid Varnish hitting this cookies? (If I got correctly the idea about avoiding Vanrish hitting the cookie and not caching the home page). Thank you for any help!

    Read the article

  • Can I use iptables on my Varnish server to forward HTTPS traffic to a specific server?

    - by Dylan Beattie
    We use Varnish as our front-end web cache and load balancer, so we have a Linux server in our development environment, running Varnish with some basic caching and load-balancing rules across a pair of Windows 2008 IIS web servers. We have a wildcard DNS rule that points *.development at this Varnish box, so we can browse http://www.mysite.com.development, http://www.othersite.com.development, etc. The problem is that since Varnish can't handle HTTPS traffic, we can't access https://www.mysite.com.development/ For dev/testing, we don't need any acceleration or load-balancing - all I need is to tell this box to act as a dumb proxy and forward any incoming requests on port 443 to a specific IIS server. I suspect iptables may offer a solution but it's been a long while since I wrote an iptables rule. Some initial hacking has got me as far as iptables -F iptables -A INPUT -p tcp -m tcp --sport 443 -j ACCEPT iptables -A OUTPUT -p tcp -m tcp --dport 443 -j ACCEPT iptables -t nat -A PREROUTING -p tcp --dport 443 -j DNAT --to 10.0.0.241:443 iptables -t nat -A POSTROUTING -p tcp -d 10.0.0.241 --dport 443 -j MASQUERADE iptables -A INPUT -j LOG --log-level 4 --log-prefix 'PreRouting ' iptables -A OUTPUT -j LOG --log-level 4 --log-prefix 'PostRouting ' iptables-save > /etc/iptables.rules (where 10.0.0.241 is the IIS box hosting the HTTPS website), but this doesn't appear to be working. To clarify - I realize there's security implications about HTTPS proxying/caching - all I'm looking for is completely transparent IP traffic forwarding. I don't need to decrypt, cache or inspect any of the packets; I just want anything on port 443 to flow through the Linux box to the IIS box behind it as though the Linux box wasn't even there. Any help gratefully received... EDIT: Included full iptables config script.

    Read the article

  • few basic questions on webhosting (namservers & dns records)

    - by claws
    I bought a domain name on name.com & I want to use free webhosting on 110mb.com By default name.com integrates services of Google apps. Name server entries are ns1.name.com ns2.name.com ns3.name.com ns4.name.com When I registered on 110mb.com it gave me two addresses ns1.110mb.com ns2.110mb.com This is where I'm lost. The concept is that "Domain name should point to an address of the server where the website is hosted" right? Then why are these 4 entires by default. How exactly is it working? should I remove these 4 and then add 110mb.com servers or just append 110mb.com server addresses to name.com ones. I would like to use google apps. If I change these name server addresses would that remove google apps? I especially want to use email service of google. And I really don't understand what is CNAME, MX, or something something. I want to learn about these stuff & how it exactly works. When I search for webhost tutorial. I'm unable to find any fruitful results.

    Read the article

< Previous Page | 424 425 426 427 428 429 430 431 432 433 434 435  | Next Page >