Search Results

Search found 13082 results on 524 pages for 'ip camera'.

Page 430/524 | < Previous Page | 426 427 428 429 430 431 432 433 434 435 436 437 | Next Page >

Trouble Extending Network with Apple Airport Extreme (PC won't connect with Ethernet)

- by 0x783czar

So I have an Apple Airport Extreme base station that I use to create a wifi network at my house. But on a separate story from this station i have a PC (running Windows 7) that does not have a wireless card. Luckily, I have another Airport Extreme Base Station, so I figured I'd have my second station "extend" the existing network. I asked Apple if this was possible, which it was, and walked through the setup wizard to extend the network. Then I ran an ethernet cable from the Station to my PC. However the PC refuses to connect to the Internet. It says it can access the network, "Unidentified Network (Limited Connectivity)", but that's it. It tells me that my computer does not have an IP address. I tried running the cable to another computer (my Apple MacBook Pro) and got a similar error. Any thoughts?

Read the article
VPN still working after rebooting without client - DrayTek client shows "No Connection"

- by HeavenCore

My home network is a simple router + pc's setup, nothing fancy - the router has DHCP enabled for 192.168.0.X (255.255.255.0) and my PC picks up the address 192.168.0.82. There are no devices on my local lan in the 192.168.1.x range. On my pc i have the DrayTek VPN client, and a company i do some work for has a DrayTek Vigor router. The VPN client establishes a VPN to that remote company using an IPSec Tunnel (PreShared Key - no encryption) Last night i shut down my pc with the VPN tunnel still connected, when i turned my computer on this morning i accidentally clicked an RDP shortcut to 192.168.1.2 (a host in the remote company) and to my amazement it connected?!? I checked and the DrayTek VPN client isnt running, and when i did run it, it clearly shows "Status: No connection". confused as to how my machine can still talk to this remote machine i tried a trace: C:\Users\HeavenCore>tracert 192.168.1.2 Tracing route to C4SERVERII [192.168.1.2] over a maximum of 30 hops: 1 * * * Request timed out. 2 * * * Request timed out. 3 * * * Request timed out. 4 * * * Request timed out. 5 * * * Request timed out. 6 * * * Request timed out. 7 * * * Request timed out. 8 * * * Request timed out. 9 * * * Request timed out. 10 * * * Request timed out. 11 * * * Request timed out. 12 15 ms 21 ms 32 ms C4SERVERII [192.168.1.2] Trace complete. No indication there as to how it's getting from my network to the remote host. with my network mask being 255.255.255.0 with ip 192.168.0.1 i dont even see how packets are routing to 192.168.1.1 - unless there was a static route in place, so i checked the route table: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.0.1 192.168.0.82 266 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.0 On-link 192.168.0.82 266 192.168.0.82 255.255.255.255 On-link 192.168.0.82 266 192.168.0.255 255.255.255.255 On-link 192.168.0.82 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.0.82 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.0.82 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.0.1 Default =========================================================================== As far as i can see, nothing indicating how my packets are getting to 192.168.1.2??? To confirm i was on a different subnet i did an ipconfig /all: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Marvell Yukon 88E8056 PCI-E Gigabit Ether net Controller Physical Address. . . . . . . . . : 00-23-54-F3-4E-BA DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.82(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.1 DNS Servers . . . . . . . . . . . : 192.168.0.1 208.67.222.222 NetBIOS over Tcpip. . . . . . . . : Enabled Yet straight after confirming my ip and subnet as above i can go ahead and ping the remote machine: C:\Users\HeavenCore>ping 192.168.1.2 Pinging 192.168.1.2 with 32 bytes of data: Reply from 192.168.1.2: bytes=32 time=48ms TTL=127 Reply from 192.168.1.2: bytes=32 time=23ms TTL=127 Reply from 192.168.1.2: bytes=32 time=103ms TTL=127 Reply from 192.168.1.2: bytes=32 time=25ms TTL=127 Ping statistics for 192.168.1.2: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 23ms, Maximum = 103ms, Average = 49ms Also, note on the ping how the times are 35ms ish, this clearly shows the pings are to the remote host and not something on my local lan (all stuff on my local lan pings in 0ms) - plus i verified the host was actually the host via RDP. My Question: Can an IPSec tunnel stay up some how after a reboot without use of the VPN client? (well, i can clearly see that it can) - where in windows is there visibility of this? how does my machine know where to route the packets? I appreciate any insights & thoughts!

Read the article
questions about multi threading for sockets/tcp-connections.

- by Fantastic Fourier

I have a server that connects to multiple clients using TCP/IP connections, using C in Unix. Since it won't have more than 20 connections at a time, I figured I would use a thread per connection/socket. But the problem is writing to the sockets as I'll be sending user prompted msgs to clients. Once each socket is handled by a thread, how do I interact with the created thread to write to the sockets? Should each thread just read from the sockets and I'll write to sockets in the main program? Not sure if that's a good way to go about it.

Read the article
Security problem

- by Mehmet Kaleli

Hi All. I have a security problem in my website. A script code was added into my all pages like "<script src="Ip address/viewpic.asp"></script>" . It is between </head> and <body> tag. Now Google says "this site may be hartful for your pc!" about my site. How can i secure my website? I use C# and Visual Studio 2008.

Read the article
NLB and Host Header Value

- by Hafeez

Background: We are using MOSS 2007 in farm configuration, 2 WFE, 1 Indexer and SQL Server. MS NLB is used for load balancing. Host header value mapped to Virtual IP of Cluster in DNS, is used while creating the web applications in MOSS and all are sharing port 80. Problem: When client tries to access the web application that are configured with host header values. Both of WFEs Hangs for 5 minutes, they stop responding to ping and browser shows 'Page not found'. In the Application Log on the WFE, this error is registered "provider: TCP Provider, error: 0 - The semaphore timeout period has expired". Interestingly, the web application with no host header value and hosted on different ports is working correctly. Any clue to solve this problem will be helpful. Thks. Hafeez

Read the article
resolving localhost in php so can be views outside VM

- by DA

I'm running Windows 7. Within, I'm running Virtualbox and Ubuntu. Within Ubuntu, I'm running Apache and using PHP codeigniter. To reference our CSS and JS files, we use this syntax: <?php echo site_url('css/styles.css'); ?> When viewing the site locally (within Ubuntu VM) that resolves to: http://localhost/styles.css So works fine. The catch is when I access that site from within Windows 7 (for IE testing). To access the site in Windows 7, I refer to the IP address of the VM: http://xx.x.x.x/ That loads the site but, alas, all the site_url variables are still being rewritten as 'localhost'. Said files obviously don't exist on the localhost of my windows 7. Is there a way around this short of just hard-coding relative links in my PHP file?

Read the article
Bitbanging a PIO on Coldfire/ucLinux

- by G Forty

Here's the problem: I need to program some hardware via 2 pins of the PIO (1 clock, 1 data). Timing constraints are tight - 10ms clock cycle time. All this, of course, whilst I maintain very high level services (CAN bus, TCP/IP). The downstream unit also ACKS by asserting a PIO pin, configured as an input, high. So this loop has to both read and write. I need to send 16 bits in the serial stream. Is there an established way to do this sort of thing or should I simply get the hardware guys to add a PIC or somesuch. I'd much prefer to avoid exotics like RTAI extensions at this stage. I did once see a reference to user-mode IO which implied a possible interrupt driven driver but lost track of it. Any pointers welcomed.

Read the article
Why do ICMP Redirct Host happen?

- by El Barto

I'm setting up a Debian box as a router for 4 subnets. For that I have defined 4 virtual interfaces on the NIC where the LAN is connected (eth1). eth1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.1.1 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:d98/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6026521 errors:0 dropped:0 overruns:0 frame:0 TX packets:35331299 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:673201397 (642.0 MiB) TX bytes:177276932 (169.0 MiB) Interrupt:19 Base address:0x6000 eth1:0 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.2.1 Bcast:10.1.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth1:1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.3.1 Bcast:10.1.3.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth1:2 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.4.1 Bcast:10.1.4.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth2 Link encap:Ethernet HWaddr 6c:f0:49:a4:47:38 inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:fea4:4738/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:199809345 errors:0 dropped:0 overruns:0 frame:0 TX packets:158362936 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:3656983762 (3.4 GiB) TX bytes:1715848473 (1.5 GiB) Interrupt:27 eth3 Link encap:Ethernet HWaddr 94:0c:6d:82:c8:72 inet addr:192.168.2.5 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:c872/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:110814 errors:0 dropped:0 overruns:0 frame:0 TX packets:73386 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:16044901 (15.3 MiB) TX bytes:42125647 (40.1 MiB) Interrupt:20 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:22351 errors:0 dropped:0 overruns:0 frame:0 TX packets:22351 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2625143 (2.5 MiB) TX bytes:2625143 (2.5 MiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:41358924 errors:0 dropped:0 overruns:0 frame:0 TX packets:23116350 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:3065505744 (2.8 GiB) TX bytes:1324358330 (1.2 GiB) I have two other computers connected to this network. One has IP 10.1.1.12 (subnet mask 255.255.255.0) and the other one 10.1.2.20 (subnet mask 255.255.255.0). I want to be able to reach 10.1.1.12 from 10.1.2.20. Since packet forwarding is enabled in the router and the policy of the FORWARD chain is ACCEPT (and there are no other rules), I understand that there should be no problem to ping from 10.1.2.20 to 10.1.1.12 going through the router. However, this is what I get: $ ping -c15 10.1.1.12 PING 10.1.1.12 (10.1.1.12): 56 data bytes Request timeout for icmp_seq 0 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 81d4 0 0000 3f 01 e2b3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 1 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 899b 0 0000 3f 01 daec 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 2 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 78fe 0 0000 3f 01 eb89 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 3 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 14b8 0 0000 3f 01 4fd0 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 4 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 8ef7 0 0000 3f 01 d590 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 5 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 ec9d 0 0000 3f 01 77ea 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 6 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 70e6 0 0000 3f 01 f3a1 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 7 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 b0d2 0 0000 3f 01 b3b5 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 8 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 f8b4 0 0000 3f 01 6bd3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 9 Request timeout for icmp_seq 10 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 1c95 0 0000 3f 01 47f3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 11 Request timeout for icmp_seq 12 Request timeout for icmp_seq 13 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 62bc 0 0000 3f 01 01cc 10.1.2.20 10.1.1.12 Why does this happen? From what I've read the Redirect Host response has something to do with the fact that the two hosts are in the same network and there being a shorter route (or so I understood). They are in fact in the same physical network, but why would there be a better route if they are not on the same subnet (they can't see each other)? What am I missing? Some extra info you might want to see: # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.8.0.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 127.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 lo 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth3 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 192.168.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth2 10.1.4.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.3.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth2 0.0.0.0 192.168.2.1 0.0.0.0 UG 100 0 0 eth3 # iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # iptables -L -n -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- !10.0.0.0/8 10.0.0.0/8 MASQUERADE all -- 10.0.0.0/8 !10.0.0.0/8 Chain OUTPUT (policy ACCEPT) target prot opt source destination

Read the article
What would be the disadvantages/risks of using AF_UNSPEC?

- by Kiril Kirov

From Beej's Guide to Network programming You can force it to use IPv4 or IPv6 in the ai_family field, or leave it as AF_UNSPEC to use whatever. This is cool because your code can be IP version-agnostic. As the title says - what would be the disadvantages (or risks, if any) of always using AF_UNSPEC, instead of specifying IPv4 or IPv6? Or it's only for one reason - if the version is specified, this will guarantee that this and only this version is supported? A little background - I think about adding support for IPv6 in client-server (C++) applications and both versions should be supported. So I wondered if it's fine to use AF_UNSPEC or it's better to "recognize" the address from the string and use AF_INET6 or AF_INET, depending on the address.

Read the article
Help needed to resolve RMI RemoteException

- by Gabriel Parenza

Hello friends, Any idea why do I get RemoteException while trying to invoke methods on Unix machine from Windows. I am inside the network and dont think this is because of firewall problem as I can do "telnet" from Windows to Unix box after starting the RMI server at the unix box. I also could not understand why is it going to local loopback IP? Stack Trace:: RemoteException occured, details java.rmi.ConnectException: Connection refused to host: 127.0.0.1; nested exception is: java.net.ConnectException: Connection refused: connect java.rmi.ConnectException: Connection refused to host: 127.0.0.1; nested exception is: java.net.ConnectException: Connection refused: connect Many thanks in advance.

Read the article
SocketTimeOutException while creating socket, java

- by Sunil Kumar Sahoo

Hi All, I have created a sample java socket application. I used Socket s = new Socket(ip, port) Now it works fine. but when my internet connection is very slow that time after a long interval (even if sometimes after 2 minutes) i used to get SocketTimeOutException in that line. means it gives that error while creating socket. I want the exception should be handled properly means if internet connection is very slow then if that error occurs it happens very late now . I want if this type of error occurs then it should be caught very fast means the error should not come at such a delay interval of time rather it should come immediately. How to achieve this. Thanks Sunil Kumar Sahoo

Read the article
Hash 32bit int to 16bit int?

- by dkamins

What are some simple ways to hash a 32-bit integer (e.g. IP address, e.g. Unix time_t, etc.) down to a 16-bit integer? E.g. hash_32b_to_16b(0x12345678) might return 0xABCD. Let's start with this as a horrible but functional example solution: function hash_32b_to_16b(val32b) { return val32b % 0xffff; } Question is specifically about JavaScript, but feel free to add any language-neutral solutions, preferably without using library functions. Simple = good. Wacky+obfuscated = amusing.

Read the article
Windows IIS test server setup

- by chopps

hello everyone, I picked up a new server to do some testing and need of a little help in setting up my environment at home. Here is what I would like to do: The test server will be used to test new code and configurations for a SaaS product. I would like from my laptop to enter www.acme.com and have it hit the server. The server is connected to a wireless router. I have windows server 2008 with IIS running on an an IP of 192.168.1.4. What is the best way to set this up? I want to hit the test server for www.acme.com and not go out to the internet. Do i need to mess with the LMHosts file? Thanks for the help. Im sure its easy but have never done this before.

Read the article
Illegal instruction in Assembly

- by Natasha

I really do not understand why this simple code works fine in the first attempt but when putting it in a procedure an error shows: NTVDM CPU has encountered an illegal instruction CS:db22 IP:4de4 OP:f0 ff ff ff ff The first code segment works just fine: .model small .stack 100h .code start: mov ax,@data mov ds,ax mov es,ax MOV AH,02H ;sets cursor up MOV BH,00H MOV DH,02 MOV DL,00 INT 10H EXIT: MOV AH,4CH INT 21H END However This generates an error: .model small .stack 100h .code start: mov ax,@data mov ds,ax mov es,ax call set_cursor PROC set_cursor near MOV AH,02H ;sets cursor up MOV BH,00H MOV DH,02 MOV DL,00 INT 10H RET set_cursor ENDP EXIT: MOV AH,4CH INT 21H END Note: Nothing is wrong with windows config. I have tried many sample codes that work fine Thanks

Read the article
StackExchange API key

- by user21289

I am working on a project with the StackExchange API, the problem is at a moment I have this Exception on eclipse console: java.io.IOException: Server returned HTTP response code: 400 for URL: https://api.stackexchange.com/2.1/questions?order=desc&sort=votes&tagged=OSM&site=stackoverflow at sun.net.www.protocol.http.HttpURLConnection.getInputStream(Unknown Source) at sun.net.www.protocol.https.HttpsURLConnectionImpl.getInputStream(Unknown Source) atbr.inf.pucrio.sog.StackOverflowAcessor.getQuestionsIds(StackOverflowAcessor.java:41) After verifying on the browser with the same link, I have this error message: {"error_id":502,"error_name":"throttle_violation","error_message":"too many requests from this IP, more requests available in 74089 seconds"} I am wondering if this is dur to the limited numbers of the queries per day, if it is the case, how can I do to have the key? if it is not, how can I do to resolve the problem?

Read the article
IPv6 parsing in C

- by The Stig

I wanted to know how i can parse an IPv6 address in 'C' and convert it to a 128 bit value? So a hex address like 1:22:333:aaaa:b:c:d:e:f needs to be converted to its 128 bit equivalent binary. The problem is the IP address could be of the type ::2 and its variant since they are valid IPv6 address. The input is from the keyboard and hence is in ASCII format. Any suggestions or pointers will be appreciated. Thanks!!!

Read the article
php, mySQL - how to create a table?

- by user296516

Hi guys, I have written a code that should check weather there is a table called imei.$addimei and, if not, create it... $userdatabase = mysqli_connect('localhost', 'root', 'marina', 'imei'); ... $result = mysqli_query($userdatabase, "SELECT * FROM imei".$addimei."" ); if ( !$result ) { echo('creating table...'); /// if no such table, make one! mysql_query ( $userdatabase, 'CREATE TABLE imei'.$addimei.'( ID int NOT NULL AUTO_INCREMENT, PRIMARY KEY(ID), EVENT varchar(15), TIME varchar(25), FLD1 varchar(35), FLD2 varchar(35), IP varchar(25), )' ); } Yet the CREATE TABLE somehow doesn't seem to work. Warning: mysql_query() expects parameter 1 to be string, object given in C:\xampp\xampp\htdocs\mobi\mainmenu.php on line 564 Any idea's what wrong? Thanks!

Read the article
testing database application remotely

- by vbNewbie

With advice from users here I was able to deploy an application that connects with sql server 2008 database on to a server. I have the connection string with data source pointing to my machine since the database is stored on my machine temporarily. I do not have access to another machine and wanted to test the application so I remotely connected to the server to test the application and it does not connect to the server. I have TCP/IP enables, port to defaul 1433, and remote connections checked. Is there something I am missing? Please help

Read the article
Too many values problem

- by DraskyVanderhoff

Hi , i was trying to make a full lot of ips for testing using this code : ip_is = [i for i in range(256)] ports = [i for i in range(1024,49152)] return [str(i1)+"."+str(i2)+"."+str(i3)+"."+str(i4)+":"+str(p) for i1,i2,i3,i4,port in ip_is,ip_is,ip_is,ip_is,ports] The problem is the 3rd line in which is made the ip list. If there is a way to make it all at once or how can make one at time in a lazy way ? I'm pretty noob at python :P. Thanks for the Help :)

Read the article
Powershell - Splitting variable into chunks

- by Andrew

I have written a query in Powershell interrogating a F5 BIG-IP box through it's iControl API to bring back CPU usage etc. Using this code (see below) I can return the data back into a CSV format which is fine. However the $csvdata variable contains all the data. I need to be able to take this variable and for each line split each column of data into a seperate variable. The output currently looks like this: timestamp,"Utilization" 1276181160,2.3282800000e+00 Any advice would be most welcome $SystemStats = (Get-F5.iControl).SystemStatistics ### Allocate a new Query Object and add the inputs needed $Query = New-Object -TypeName iControl.SystemStatisticsPerformanceStatisticQuery $Query.object_name = $i $Query.start_time = $startTime $Query.end_time = 0 $Query.interval = $interval $Query.maximum_rows = 0 ### Make method call passing in an array of size one with the specified query $ReportData = $SystemStats.get_performance_graph_csv_statistics( (,$Query) ) ### Allocate a new encoder and turn the byte array into a string $ASCII = New-Object -TypeName System.Text.ASCIIEncoding $csvdata = $ASCII.GetString($ReportData[0].statistic_data)

Read the article
How can I find the places of system calls of my program?

- by Lucky Man

From strace manual: -i Print the instruction pointer at the time of the system call. I straced my programm: strace -i prog As a result I got a lot of system calls. One of them: [000da49c] open("./rabbit.o", O_RDONLY) = 3 But disassembled instruction at this address of prog doesn't call any syscall (hte editor): da49c ! mov r7, ip What is wrong? How can I find the places of system calls of my program? P.S. Architecture of my device doesn't support GDB-command catch syscall.

Read the article
Program occasionally stuck when writing to ldap

- by djerry

hey guys, I have 2 databases for my program : mysql and ldap. All transactions happen to mysql, but i need ldap to connect to ip-phones. There's an option to synchronise the ldap database. So when the ldap is brand new, and mysql contains like 200+ records, it may want to update. But when inserting all those entries, it "freezes". It never happens at the same record, it's very random. Sometimes after 70 records, sometimes at 200 the program quits inserting, and gets stuck. This is very annoying. My best guess is that ldap can't handle that much inserts in a short time. Code isn't the problem, as it is a random problem. Does this seem familiar to somebody or is it just me? Thanks in advance.

Read the article
Delphi - COM/OLE starting example needed

- by durumdara

Hi! 10 years have ellapsed since I used COM/OLE, and I forget 90% of them. Now we need to make a COM object to access some data from PHP/Python (this is specific thing, the php ODBC don't access the output params of a DataBase - like stored proc output), and my idea the I realize a minimal object with one method, and PHP/Python can call this to get the output... procedure ExecSQL(Config, IP, Port, DBName, SQL, IDFieldName : variant) : output output is [IDValue, ErrorMsg, HResult] Please help me a very little example, how to start it? I need only this, but I'm confused by many ActiveX/COM in the palette. What I need to use to make a simple COM DLL, and how to register my COM object with this DLL? Thanks: dd

Read the article
ASP.NET Request.ServerVariables["SERVER_PORT_SECURE"] and proxy SSL by load balancer

- by frankadelic

We have some legacy ASP.NET code that detects if a request is secure, and redirects to the https version of the page if required. This code uses Request.ServerVariables["SERVER_PORT_SECURE"] to detect if SSL is needed. Our operations team has suggested doing proxy SSL at the load balancer (F5 Big-IP) instead of on the web servers (assume for the purposes of this question that this is a requirement). The consequence would be that all requests appear as HTTP to the web server. My question: how can we let the web servers known that the incoming connection was secure before it hit the load balancer? Can we continue to use Request.ServerVariables["SERVER_PORT_SECURE"]? Do you know of a load balancer config that will send headers so that no application code changes are needed?

Read the article
Penalty clause on programming contract

- by Everyone

I am considering the move to the other side of development, as a contract programmer. SO has given me a good few hints on the kind of figures to quote ( and why ), and a few points to bear in mind such as Non-competition and [IP Protection] Having worked as a programmer for a while, I know that a few reasons for deadline delays may be - Estimates can be all over the place both from the Contractor, and the Job provider Things like bandwidth bottlenecks, merge for high-impact code etc Clarification time on provided requirements... etc If you have worked as a contract programmer then How frequently do you encounter a penalty/forfeit clause in your agreement? What do you deem unacceptable in the penalty/forfeit clause?

Read the article

< Previous Page | 426 427 428 429 430 431 432 433 434 435 436 437 | Next Page >