Search Results

Search found 11840 results on 474 pages for 'assembly context'.

Page 432/474 | < Previous Page | 428 429 430 431 432 433 434 435 436 437 438 439  | Next Page >

• Juniper SSG-5 subinterface vlan routing to the internet

  - by catfish

  I'm unable to get a brand new Juniper SSG-5 with latest 6.3.0r05 firmware routing to the internet from a subinterface I created on bgroup0 setup as vlan2 (bgroup0.1 on "wifi" zone). When connected on the default vlan it gets on the internet just fine. When I switch to vlan2 I'm unable to get to the internet. I am able to get the correct ip address (10.150.0.0/24) from dhcp, able to get to the juniper management page, etc but nothing past the firewall, can't ping 4.2.2.2 or the internet gateway. Even setting up logging on the wifi-to-untrust policy and it does shows the attempts (it's it's timeouts). 172.31.16.0/24 is the untrusted lan, it's already nat'ed but works fine for testing. Can ping this ip from the default vlan but not from vlan2 192.168.1.0/24 is the trusted main lan 10.150.0.0/24 is the wifi isolated lan on vlan2 The idea is to setup an AP with lan and guest access (AP supports multiple ssid's on different vlans). I know I can setup the juniper to use different ports for the wifi lan and use their procurve switch to do the vlan separation, but I never used vlan'ing on a Juniper firewall and I would like to try it out this way. Here is the complete config file: unset key protection enable set clock timezone -5 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set alg appleichat enable unset alg appleichat re-assembly enable set alg sctp enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin name "netscreen" set admin password "xxxxxxxxxxxxxxxx" set admin auth web timeout 10 set admin auth dial-in timeout 3 set admin auth server "Local" set admin format dos set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone id 100 "Wifi" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "MGT" block unset zone "V1-Trust" tcp-rst unset zone "V1-Untrust" tcp-rst set zone "DMZ" tcp-rst unset zone "V1-DMZ" tcp-rst unset zone "VLAN" tcp-rst unset zone "Wifi" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Untrust" set interface "bgroup0" zone "Trust" set interface "bgroup0.1" tag 2 zone "Wifi" set interface "bgroup1" zone "DMZ" set interface bgroup0 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup0 port ethernet0/5 set interface bgroup0 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 172.31.16.243/24 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup0.1 ip 10.150.0.1/24 set interface bgroup0.1 nat set interface bgroup0.1 mtu 1500 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup0.1 ip manageable set interface ethernet0/0 manage ping set interface ethernet0/1 manage ping set interface bgroup0.1 manage ping set interface bgroup0.1 manage telnet set interface bgroup0.1 manage web unset interface bgroup1 manage ping set interface bgroup0 dhcp server service set interface bgroup0.1 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup0.1 dhcp server enable set interface bgroup0 dhcp server option gateway 192.168.1.1 set interface bgroup0 dhcp server option netmask 255.255.255.0 set interface bgroup0 dhcp server option dns1 8.8.8.8 set interface bgroup0.1 dhcp server option lease 1440 set interface bgroup0.1 dhcp server option gateway 10.150.0.1 set interface bgroup0.1 dhcp server option netmask 255.255.255.0 set interface bgroup0.1 dhcp server option dns1 8.8.8.8 set interface bgroup0 dhcp server ip 192.168.1.33 to 192.168.1.126 set interface bgroup0.1 dhcp server ip 10.150.0.50 to 10.150.0.100 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup0.1 dhcp server config next-server-ip set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set flow tcp-mss unset flow no-tcp-seq-check set flow tcp-syn-check unset flow tcp-syn-bit-check set flow reverse-route clear-text prefer set flow reverse-route tunnel always set pki authority default scep mode "auto" set pki x509 default cert-path partial set crypto-policy exit set ike respond-bad-spi 1 set ike ikev2 ike-sa-soft-lifetime 60 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit set policy id 1 exit set policy id 2 from "Wifi" to "Untrust" "Any" "Any" "ANY" permit log set policy id 2 exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 unset license-key auto-update set telnet client enable set snmp port listen 161 set snmp port trap 162 set snmpv3 local-engine id "0162122009006149" set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route set route 0.0.0.0/0 interface ethernet0/0 gateway 172.31.16.1 exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit

  Read the article

• OpenGL/SharpGL - Points only on -near surface of Ortho projection?

  - by FTLPhysicsGuy

  When you create points using three dimensions for each point and you use an Ortho projection to view the points, would there be a reason that only the points on the -near surface would appear? For example, if you use (the SharpGL method) gl.Ortho(0, width, height, 0, -10, 10), only the points at z=10 (because the near surface is at -10) actually show up. I'm currently using SharpGL - but I'm hoping the issue I'm having isn't with that particular implementation/library. EDIT: I'm adding the code below that demonstrates the issue. Note that this example requires SharpGL and is in fact a modification of a WPF sample project that comes with the current SharpGL source code (the original sample project is called TwoDSample). The project requires a MainWindow.xaml and a MainWindow.xaml.cs. Here's the xaml: <Window x:Class="TwoDSample.MainWindow" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" Title="MainWindow" Height="350" Width="525" xmlns:my="clr-namespace:SharpGL.WPF;assembly=SharpGL.WPF"> <Grid> <my:OpenGLControl Name="openGLControl1" OpenGLDraw="openGLControl1_OpenGLDraw" OpenGLInitialized="openGLControl1_OpenGLInitialized" Resized="openGLControl1_Resized"/> </Grid> </Window> Here is the code behind: using System; using System.Collections.Generic; using System.Linq; using System.Text; using System.Windows; using System.Windows.Controls; using System.Windows.Data; using System.Windows.Documents; using System.Windows.Input; using System.Windows.Media; using System.Windows.Media.Imaging; using System.Windows.Navigation; using System.Windows.Shapes; using SharpGL.Enumerations; namespace TwoDSample { /// <summary> /// Interaction logic for MainWindow.xaml /// </summary> public partial class MainWindow : Window { public MainWindow() { InitializeComponent(); } // NOTE: I use this to restrict the openGLControl1_OpenGLDraw method to // drawing only once after m_drawCount is set to zero; int m_drawCount = 0; private void openGLControl1_OpenGLDraw(object sender, SharpGL.SceneGraph.OpenGLEventArgs args) { // NOTE: Only draw once after m_drawCount is set to zero if (m_drawCount < 1) { // Get the OpenGL instance. var gl = args.OpenGL; gl.Color(1f, 0f, 0f); gl.PointSize(2.0f); // Draw 10000 random points. gl.Begin(BeginMode.Points); Random random = new Random(); for (int i = 0; i < 10000; i++) { double x = 10 + 400 * random.NextDouble(); double y = 10 + 400 * random.NextDouble(); double z = (double)random.Next(-10, 0); // Color the point according to z value gl.Color(0f, 0f, 1f); // default to blue if (z == -10) gl.Color(1f, 0f, 0f); // Red for z = -10 else if (z == -1) gl.Color(0f, 1f, 0f); // Green for z = -1 gl.Vertex(x, y, z); } gl.End(); m_drawCount++; } } private void openGLControl1_OpenGLInitialized(object sender, SharpGL.SceneGraph.OpenGLEventArgs args) { } private void openGLControl1_Resized(object sender, SharpGL.SceneGraph.OpenGLEventArgs args) { // NOTE: force the draw routine to happen again when resize occurs m_drawCount = 0; // Get the OpenGL instance. var gl = args.OpenGL; // Create an orthographic projection. gl.MatrixMode(MatrixMode.Projection); gl.LoadIdentity(); // NOTE: Basically no matter what I do, the only points I see are those at // the "near" surface (with z = -zNear)--in this case, I only see green points gl.Ortho(0, openGLControl1.ActualWidth, openGLControl1.ActualHeight, 0, 1, 10); // Back to the modelview. gl.MatrixMode(MatrixMode.Modelview); } } }

  Read the article

• Download a file with DefaultHTTPClient and preemptive authentication

  - by Nils

  After I had a lot of problems with preemptive authentication , I got it finally working. Now the next problem. I want to get a file with it, but I don't know how. I thought the file data might be in the variable response, but it isn't. Any ideas how this might work? I'm trying it since days without success :( - Basically I'm trying to download an jpeg file, which is on a server protected by prem. auth. // BASIC AUTH /* * ==================================================================== * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. * The ASF licenses this file to You under the Apache License, Version 2.0 * (the "License"); you may not use this file except in compliance with * the License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. * See the License for the specific language governing permissions and * limitations under the License. * ==================================================================== * * This software consists of voluntary contributions made by many * individuals on behalf of the Apache Software Foundation. For more * information on the Apache Software Foundation, please see * <http://www.apache.org/>. */ //http://svn.apache.org/repos/asf/httpcomponents/httpclient/branches/4.0.x/httpclient/src/examples/org/apache/http/examples/client/ClientPreemptiveBasicAuthentication.java httpclient = new DefaultHttpClient(); httpclient.getCredentialsProvider().setCredentials( new AuthScope(host, port), new UsernamePasswordCredentials(username, password)); // Generate BASIC scheme object and stick it to the local // execution context BasicHttpContext localcontext = new BasicHttpContext(); BasicScheme basicAuth = new BasicScheme(); localcontext.setAttribute("preemptive-auth", basicAuth); //first request interceptor httpclient.addRequestInterceptor(new PreemptiveAuth(), 0); HttpHost targetHost = new HttpHost(host, port, "http"); //HttpGet httpget = new HttpGet("/"); HttpGet httpget = new HttpGet(http.url); System.out.println("executing request" + httpget.getRequestLine()); /// !!! HttpResponse response = httpclient.execute(targetHost, httpget, localcontext); HttpEntity entity = response.getEntity(); System.out.println("----------------------------------------"); System.out.println("+"+response.getStatusLine()+"+"); ...

  Read the article

• NHibernate LINQ query throws error "Could not resolve property"

  - by Xorandor

  I'm testing out using LINQ with NHibernate but have run into some problems with resolving string.length. I have the following public class DC_Control { public virtual int ID { get; private set; } public virtual string Name { get; set; } public virtual bool IsEnabled { get; set; } public virtual string Url { get; set; } public virtual string Category { get; set; } public virtual string Description { get; set; } public virtual bool RequireScriptManager { get; set; } public virtual string TriggerQueryString { get; set; } public virtual DateTime? DateAdded { get; set; } public virtual DateTime? DateUpdated { get; set; } } public class DC_ControlMap : ClassMap<DC_Control> { public DC_ControlMap() { Id(x => x.ID); Map(x => x.Name).Length(128); Map(x => x.IsEnabled); Map(x => x.Url); Map(x => x.Category); Map(x => x.Description); Map(x => x.RequireScriptManager); Map(x => x.TriggerQueryString); Map(x => x.DateAdded); Map(x => x.DateUpdated); } } private static ISessionFactory CreateSessionFactory() { return Fluently.Configure() .Database(FluentNHibernate.Cfg.Db.MsSqlConfiguration.MsSql2008) .Mappings(m => m.FluentMappings.AddFromAssembly(Assembly.GetExecutingAssembly())) .ExposeConfiguration(c => c.SetProperty("connection.connection_string", "CONNSTRING")) .ExposeConfiguration(c => c.SetProperty("proxyfactory.factory_class", "NHibernate.ByteCode.Castle.ProxyFactoryFactory,NHibernate.ByteCode.Castle")) .BuildSessionFactory(); } public static void test() { using (ISession session = sessionFactory.OpenSession()) { var sqlQuery = session.CreateSQLQuery("select * from DC_Control where LEN(url) > 80").AddEntity(typeof(DC_Control)).List<DC_Control>(); var linqQuery= session.Linq<DC_Control>().Where(c => c.Url.Length > 80).ToList(); } } In my test method I first try and perform the query using SQL, this works just fine. Then I want to do the same thing in LINQ, and it throws the following error: NHibernate.QueryException: could not resolve property: Url.Length of: DC_Control I've searched alot for this "could not resolve property" error, but I can't quite figure out, what this means. Is this because the LINQ implementation is not complete? If so it's a bit disappointing coming from Linq2Sql where this would just work. I also tried it setting up the mapping with a hbm.xml instead of using FluentNHibernate but it produced teh same error.

  Read the article

• Replacing UISplitViewController. New version isn't added for current orientation, frame size

  - by Justin Williams

  My application has two different modes I am switching between by replacing the two views in a UISplitViewController. This involves instantiating the new views and a new UISplitViewController. I then set the new detail view as the UISplitViewController's delegate. I'm running into an issue where when I replace the view controllers and splitview controller, they are not properly sized or added for the current orientation. For instance, if I have my iPad in UIDeviceOrientationPortraitUpsideDown the view will be upside down when I call addSubview, but will rotate to the proper orientation after a second. In another instance, if I have the device in landscape mode and swap the views, the detail view controller is not fully stretched to the size of the view. If I rotate the device to portrait and back to landscape, its resized properly. The code I'm using to create the new split view and view controllers is as follows. - (void)showNotes { teiphoneAppDelegate *appDelegate = (teiphoneAppDelegate *)[[UIApplication sharedApplication] delegate]; [appDelegate.splitViewController.view removeFromSuperview]; OMSavedScrapsController *notesViewController = [[OMSavedScrapsController alloc] initWithNibName:@"SavedScraps" bundle:nil]; UINavigationController *navController = [[UINavigationController alloc] initWithRootViewController:notesViewController]; ComposeViewController *noteDetailViewController = [[ComposeViewController alloc] initWithNibName:@"ComposeView-iPad" bundle:nil]; UISplitViewController *newSplitVC = [[UISplitViewController alloc] init]; newSplitVC.viewControllers = [NSArray arrayWithObjects:navController, noteDetailViewController, nil]; newSplitVC.delegate = noteDetailViewController; appDelegate.splitViewController = newSplitVC; // Fade in the new split view appDelegate.splitViewController.view.alpha = 0.0f; [appDelegate.window addSubview:appDelegate.splitViewController.view]; [appDelegate.window makeKeyAndVisible]; [UIView beginAnimations:nil context:appDelegate.window]; [UIView setAnimationDuration: 0.5f]; [UIView setAnimationCurve: UIViewAnimationCurveEaseInOut]; appDelegate.splitViewController.view.alpha = 1.0f; [UIView commitAnimations]; [notesViewController release]; [navController release]; [noteDetailViewController release]; [newSplitVC release]; } Any suggestions for how to get the new splitview to add for the device's current orientation and frame?

  Read the article

• Debugging XSLT with extension objects in Visual Studio 2010

  - by Alex Ciminian

  I'm currently working on a project that involves a lot of XSLT transformations and I really need a debugger (I have XSLTs that are 1000+ lines long and I didn't write them :-). The project is written in C# and makes use of extension objects: xslArg.AddExtensionObject("urn:<obj>", new <Obj>()); From my knowledge, in this situation Visual Studio is the only tool that can help me debug the transformations step-by-step. The static debugger is no use because of the extension objects (it throws an error when it reaches elements that reference their namespace). Fortunately, I've found this thread which gave me a starting point (at least I know it can be done). After searching MSDN, I found the criteria that makes stepping into the transform possible. They are listed here. In short: the XML and the XSLT must be loaded via a class that has the IXmlLineInfo interface (XmlReader & co.) the XML resolver used in the XSLTCompiledTransform constructor is file-based (XmlUriResolver should work). the stylesheet should be on the local machine or on the intranet (?) From what I can tell, I fit all these criteria, but it still doesn't work. The relevant code samples are posted below: // [...] xslTransform = new XslCompiledTransform(true); xslTransform.Load(XmlReader.Create(new StringReader(contents)), null, new BaseUriXmlResolver(xslLocalPath)); // [...] // I already had the xml loaded in an xmlDocument // so I have to convert to an XmlReader XmlTextReader r = new XmlTextReader(new StringReader(xmlDoc.OuterXml)); XsltArgumentList xslArg = new XsltArgumentList(); xslArg.AddExtensionObject("urn:[...]", new [...]()); xslTransform.Transform(r, xslArg, context.Response.Output); I really don't get what I'm doing wrong. I've checked the interfaces on both XmlReader objects and they implement the required one. Also, BaseUriXmlResolver inherits from XmlUriResolver and the stylesheet is stored locally. The screenshot below is what I get when stepping into the Transform function. First I can see the stylesheet code after stepping through the parameters (on template-match), I get this: If anyone has any idea why it doesn't work or has an alternative way of getting it to work I'd be much obliged :). Thanks, Alex

  Read the article

• Cannot get UISearchBar Scope Bar to appear in Toolbar on iPad

  - by Jann

  This is really causing me fits. I put a toolbar on the IUView on the iPad. I added the following: Search Bar (not Search Bar and Search Display) to the toolbar. I set the options to be as follows: Show Cancel Button, Show Scope Bar, Scope Button Titles are: "Title1" and "Title2" (with Title2's radio button selected). Opaque, Clear Context and Auto Resize are checked. I hooked up the delegate of Search Bar to the "File's Owner" and linked it to IBOutlet theSearchBar. In my viewWillAppear I have the following: [theSearchBar setScopeButtonTitles:[NSArray arrayWithObjects:@"Near Me",@"Everywhere",nil]]; //Just in case: [theSearchBar setShowsScopeBar:YES]; //doesn't seem to do anything: //[theSearchBar sizeToFit]; searchDisplayController = [[UISearchDisplayController alloc] initWithSearchBar:theSearchBar contentsController:self]; [self setSearchDisplayController:searchDisplayController]; [searchDisplayController setDelegate:self]; [searchDisplayController setSearchResultsDataSource:self]; //again--does not seem to do anything..but people have suggested it: [theSearchBar sizeToFit]; Okay, so far, I thought, so good. So, I made the File's Owner .m file to be a delegate for: UISearchBarDelegate, UISearchDisplayDelegate. My issue: I have yet to implement the delegates necessary to do the search but still... shouldn't I be seeing the scopeBar next to the search field when I click into the search field? Just so you know I DO see the log of the characters I type, so the delegate is working. I have the following dummy functions in the .m file (just in case) // called when keyboard search button pressed - (void)searchBarSearchButtonClicked:(UISearchBar *)searchBar { NSLog(@"Search Button Clicked\n"); [theSearchBar resignFirstResponder]; } // called when cancel button pressed - (void)searchBarCancelButtonClicked:(UISearchBar *)searchBar { NSLog(@"Cancel Button Clicked\n"); [theSearchBar resignFirstResponder]; } - (void)searchBar:(UISearchBar *)searchBar textDidChange:(NSString *)searchText { NSLog(@"Search Text So Far: '%@'\n",searchText); } - (BOOL)searchBarShouldBeginEditing:(UISearchBar *)searchBar { return YES; } - (BOOL)searchBarShouldEndEditing:(UISearchBar *)searchBar { return YES; } Why doesn't the Scope Bar appear? A results UIPopoverController appears with the title "Results" and "No results found" (of course) when i type the first character in my search...but no scope bar. (not that i expect anything other than "No Results Found". I am wondering where the scope bar is supposed to appear...in the titleView of the UIPopover? In the toolbar to the right of the search area? Where?

  Read the article

• How to change the data in Telerik's RadGrid based on Calendar's selected dates?

  - by Jronny

  I was creating another usercontrol with Telerik's RadGrid and Calendar. <%@ Register Assembly="Telerik.Web.UI" Namespace="Telerik.Web.UI" TagPrefix="telerik" %> <table class="style1"> <tr> <td>From</td> <td>To</td> </tr> <tr> <td><asp:Calendar ID="Calendar1" runat="server" SelectionMode="Day"></asp:Calendar></td> <td><asp:Calendar ID="Calendar2" runat="server" SelectionMode="Day"></asp:Calendar></td> </tr> <tr> <td><asp:Button ID="btnSubmit" runat="server" Text="Submit" OnClick="btnSubmit_Click" /></td> <td><asp:Button ID="btnClear" runat="server" Text="Clear" OnClick="btnClear_Click" /></td> </tr> </table> <telerik:RadGrid ID="RadGrid1" runat="server"> <MasterTableView CommandItemDisplay="Top"></MasterTableView> </telerik:RadGrid> and I am using Linq in code-behind: Entities1 entities = new Entities1(); public static object DataSource = null; protected void Page_Load(object sender, EventArgs e) { if (DataSource == null) { DataSource = (from entity in entities.nsc_moneytransaction select new { date = entity.transaction_date.Value, username = entity.username, cashbalance = entity.cash_balance }).OrderByDescending(a => a.date); } BindData(); } public void BindData() { RadGrid1.DataSource = DataSource; } protected void btnSubmit_Click(object sender, EventArgs e) { DateTime startdate = new DateTime(); DateTime enddatedate = new DateTime(); if (Calendar1.SelectedDate != null && Calendar2.SelectedDate != null) { startdate = Calendar1.SelectedDate; enddatedate = Calendar2.SelectedDate; var queryDateRange = from entity in entities.nsc_moneytransaction where DateTime.Parse(entity.transaction_date.Value.ToShortDateString()) >= DateTime.Parse(startdate.ToShortDateString()) && DateTime.Parse(entity.transaction_date.Value.ToShortDateString()) <= DateTime.Parse(enddatedate.ToShortDateString()) select new { date = entity.transaction_date.Value, username = entity.username, cashbalance = entity.cash_balance }; DataSource = queryDateRange.OrderByDescending(a => a.date); } else if (Calendar1.SelectedDate != null) { startdate = Calendar1.SelectedDate; var querySetDate = from entity in entities.nsc_moneytransaction where entity.transaction_date.Value == startdate select new { date = entity.transaction_date.Value, username = entity.username, cashbalance = entity.cash_balance }; DataSource = querySetDate.OrderByDescending(a => a.date); ; } BindData(); } protected void btnClear_Click(object sender, EventArgs e) { Calendar1.SelectedDates.Clear(); Calendar2.SelectedDates.Clear(); } The problems are, (1) when I click the submit button. the data in the RadGrid is not changed. (2) how can we check if there is nothing selected in the Calendar controls, because there is a date (01/01/0001) set even if we do not select anything from that calendar, thus Calendar1.SelectedDate != null is not enough. =( Thanks.

  Read the article

• ASP.NET MVC 2: Updating a Linq-To-Sql Entity with an EntitySet

  - by Simon

  I have a Linq to Sql Entity which has an EntitySet. In my View I display the Entity with it's properties plus an editable list for the child entites. The user can dynamically add and delete those child entities. The DefaultModelBinder works fine so far, it correctly binds the child entites. Now my problem is that I just can't get Linq To Sql to delete the deleted child entities, it will happily add new ones but not delete the deleted ones. I have enabled cascade deleting in the foreign key relationship, and the Linq To Sql designer added the "DeleteOnNull=true" attribute to the foreign key relationships. If I manually delete a child entity like this: myObject.Childs.Remove(child); context.SubmitChanges(); This will delete the child record from the DB. But I can't get it to work for a model binded object. I tried the following: // this does nothing public ActionResult Update(int id, MyObject obj) // obj now has 4 child entities { var obj2 = _repository.GetObj(id); // obj2 has 6 child entities if(TryUpdateModel(obj2)) //it sucessfully updates obj2 and its childs { _repository.SubmitChanges(); // nothing happens, records stay in DB } else ..... return RedirectToAction("List"); } and this throws an InvalidOperationException, I have a german OS so I'm not exactly sure what the error message is in english, but it says something along the lines of that the entity needs a Version (Timestamp row?) or no update check policies. I have set UpdateCheck="Never" to every column except the primary key column. public ActionResult Update(MyObject obj) { _repository.MyObjectTable.Attach(obj, true); _repository.SubmitChanges(); // never gets here, exception at attach } I've read alot about similar "problems" with Linq To Sql, but it seems most of those "problems" are actually by design. So am I right in my assumption that this doesn't work like I expect it to work? Do I really have to manually iterate through the child entities and delete, update and insert them manually? For such a simple object this may work, but I plan to create more complex objects with nested EntitySets and so on. This is just a test to see what works and what not. So far I'm disappointed with Linq To Sql (maybe I just don't get it). Would be the Entity Framework or NHibernate a better choice for this scenario? Or would I run into the same problem?

  Read the article

• Ninject 3.0 MVC kernel.bind error Auto Registration

  - by user295734

  Getting and error on kernel.Bind(scanner = ... "scanner" has the little error line under it in VS 2010. Cannot convert lambda expression to type 'System.Type[]' because it is not a delegate type Tyring to Auto Register like the old kernel.scan in 2.0. I can not figure out what i am doing wrong. Added and removed so many Ninject packages. completely lost, getting to be a big waste of time. using System; using System.Web; using Microsoft.Web.Infrastructure.DynamicModuleHelper; using Ninject; using Ninject.Web.Common; //using Ninject.Extensions.Conventions; using Ninject.Web.WebApi; using Ninject.Web.Mvc; using CommonServiceLocator.NinjectAdapter; using System.Reflection; using System.IO; using LR.Repository; using LR.Repository.Interfaces; using LR.Service.Interfaces; using System.Web.Http; public static class NinjectWebCommon { private static readonly Bootstrapper bootstrapper = new Bootstrapper(); /// <summary> /// Starts the application /// </summary> public static void Start() { DynamicModuleUtility.RegisterModule(typeof(OnePerRequestHttpModule)); DynamicModuleUtility.RegisterModule(typeof(NinjectHttpModule)); bootstrapper.Initialize(CreateKernel); } /// <summary> /// Stops the application. /// </summary> public static void Stop() { bootstrapper.ShutDown(); } /// <summary> /// Creates the kernel that will manage your application. /// </summary> /// <returns>The created kernel.</returns> private static IKernel CreateKernel() { var kernel = new StandardKernel(); kernel.Bind<Func<IKernel>>().ToMethod(ctx => () => new Bootstrapper().Kernel); kernel.Bind<IHttpModule>().To<HttpApplicationInitializationHttpModule>(); RegisterServices(kernel); return kernel; } /// <summary> /// Load your modules or register your services here! /// </summary> /// <param name="kernel">The kernel.</param> private static void RegisterServices(IKernel kernel) { kernel.Bind(scanner => scanner.FromAssembliesInPath(Path.GetDirectoryName(Assembly.GetExecutingAssembly().Location)) .Select(IsServiceType) .BindToDefaultInterface() .Configure(binding => binding.InSingletonScope()) ); } private static bool IsServiceType(Type type) { // temp return true; // .Any() is not recognized either. return true; // type.IsClass && type.GetInterfaces().Any(intface => intface.Name == "I" + type.Name); }

  Read the article

• Howto - Running Redmine on mongrel as a service on windows

  - by Achilles

  I use Redmine on Mongrel as a project manager and I use a batch file (start-redmine.bat) to start the redmine in mongrel. There are 2 issues with my setup: 1. I have a running IIS on the server that occupies the HTTP port (80) 2. The start-redmine.bat must be periodically checked to see if it's stopped after a restart that is caused by windows update service. for the first issue, I have no choice but running mongrel on a port like 3000 and for the second issue I have to create a windows service that runs automatically in the background when the windows starts; and here comes the trouble! There are at least 3 ways to run redmine as a service that I'm aware of; none of them can satisfy a performance view on this subject. you may read about them on http://stackoverflow.com/questions/877943/how-to-configure-a-rails-app-redmine-to-run-as-a-service-on-windows I tried them all. The easiest way to setup such a service is using mongrel_service approach; in 3 lines of command you're done. but the performance is significantly lower than running that batch file... Now, I wanna show you my approach: First suppose we have ruby installed into c:\ruby and we have issued the command gem install mongrel to get the mongrel gem installed into c:\ruby\bin Also, suppose we have installed the Redmine into a folder like c:\redmine; and we have ruby's path (i.e. c:\ruby\bin) in our PATH environment variable. Now Download and install the Windows NT Resource Kit Tools from microsoft website. Open the command-line tool that comes with the Resource Kit (from start menu). Use instsrv to install a dummy service called Redmine using the following command: "[path-to-instsrv.exe]\instsrv" Redmine "[path-to-srvany.exe]\srvany.exe" in my case (which is the default case) it was something like this: "C:\Program Files\Windows Resource Kits\Tools\instsrv" Redmine "C:\Program Files\Windows Resource Kits\Tools\srvany.exe" Now create the batch file. Open a notepad and paste these instructions into it and then save it as "c:\redmine\start-redmine.bat" @echo off cd c:\redmine\ mongrel_rails start -a 0.0.0.0 -p 3000 -e production Now we need to configure that dummy service we had created before. WATCH OUT WHAT YOU'RE DOING FROM HERE ON, OR YOU MAY CORRUPT YOUR WINDOWS. To configure that service, open windows registry editor (Start - Run - regedit) and navigate to this node: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Redmine Right-Click on "Redmine" node and using the context menu, create a new key called Parameters (New - Key) Right-Click on "Parameters" and create a String Value property called Application. Do this again and create another String Value called AppParameters. Now Double-click on "Application" and put cmd.exe into "Value data" section. Then Double-click on "AppParameters" and put /C "C:\redmine\start-redmine.bat" into Value data section. We're done! issue this command to run the redmine on mongrel as a service: net start Redmine

  Read the article

• qwebview in pyside after packaged with pyinstaller goes wrong

  - by truease.com

  Here's my code import sys from PySide.QtCore import * from PySide.QtGui import * from PySide.QtWebKit import * from encodings import * from codecs import * class BrowserWindow( QWidget ): def __init__( self, parent=None ): QWidget.__init__( self, parent ) self.Setup() self.SetupEvent() def Setup( self ): self.setWindowTitle( u"Truease Speedy Browser" ) self.addr_input = QLineEdit() self.addr_go = QPushButton( "GO" ) self.addr_bar = QHBoxLayout() self.addr_bar.addWidget( self.addr_input ) self.addr_bar.addWidget( self.addr_go ) for attr in [ QWebSettings.AutoLoadImages, QWebSettings.JavascriptEnabled, QWebSettings.JavaEnabled, QWebSettings.PluginsEnabled, QWebSettings.JavascriptCanOpenWindows, QWebSettings.JavascriptCanAccessClipboard, QWebSettings.DeveloperExtrasEnabled, QWebSettings.SpatialNavigationEnabled, QWebSettings.OfflineStorageDatabaseEnabled, QWebSettings.OfflineWebApplicationCacheEnabled, QWebSettings.LocalStorageEnabled, QWebSettings.LocalStorageDatabaseEnabled, QWebSettings.LocalContentCanAccessRemoteUrls, QWebSettings.LocalContentCanAccessFileUrls, ]: QWebSettings.globalSettings().setAttribute( attr, True ) self.web_view = QWebView() self.web_view.load( "http://www.baidu.com" ) layout = QVBoxLayout() layout.addLayout( self.addr_bar ) layout.addWidget( self.web_view ) self.setLayout( layout ) def SetupEvent( self ): self.connect( self.addr_input, SIGNAL("editingFinished()"), self, SLOT("Load()"), ) self.connect( self.addr_go, SIGNAL("pressed()"), self, SLOT("Load()") ) self.connect( self.web_view, SIGNAL("urlChanged(const QUrl&)"), self, SLOT("SetURL()"), ) def Load( self, *args, **kwargs ): url = self.GetCleanedURL() if url != self.CurrentURL(): self.web_view.load( url ) def SetURL( self, *args, **kwargs ): self.addr_input.setText( self.CurrentURL() ) def GetCleanedURL( self ): url = self.addr_input.text().strip() if not url.startswith("http"): url = "http://" + url return url def CurrentURL( self ): url = self.web_view.url().toString() return url def Main(): app = QApplication( sys.argv ) widget = BrowserWindow() widget.show() return app.exec_() if __name__ == '__main__': sys.exit( Main() ) I works well when i using python browser.py. but it goes wrong after packaged with pyinstaller -w browser.py. it doesn't load images can only display correct text in utf-8 And this is the pyinstaller output: E:\true\wuk\app2>pyinstaller -w b.py 16 INFO: wrote E:\true\wuk\app2\b.spec 16 INFO: Testing for ability to set icons, version resources... 32 INFO: ... resource update available 32 INFO: UPX is not available. 46 INFO: Processing hook hook-os 141 INFO: Processing hook hook-time 157 INFO: Processing hook hook-cPickle 218 INFO: Processing hook hook-_sre 312 INFO: Processing hook hook-cStringIO 407 INFO: Processing hook hook-encodings 421 INFO: Processing hook hook-codecs 750 INFO: Processing hook hook-httplib 750 INFO: Processing hook hook-email 843 INFO: Processing hook hook-email.message 1046 WARNING: library python%s%s required via ctypes not found 1171 INFO: Extending PYTHONPATH with E:\true\wuk\app2 1171 INFO: checking Analysis 1171 INFO: building because b.py changed 1171 INFO: running Analysis out00-Analysis.toc 1171 INFO: Adding Microsoft.VC90.CRT to dependent assemblies of final executable 1171 INFO: Searching for assembly x86_Microsoft.VC90.CRT_1fc8b3b9a1e18e3b_9.0.21022.8_x-ww ... 1171 INFO: Found manifest C:\WINDOWS\WinSxS\Manifests\x86_Microsoft.VC90.CRT_1fc8b3b9a1e18e3b_9.0.21022.8_x-ww_d08d0375.manifest 1187 INFO: Searching for file msvcr90.dll 1187 INFO: Found file C:\WINDOWS\WinSxS\x86_Microsoft.VC90.CRT_1fc8b3b9a1e18e3b_9.0.21022.8_x-ww_d08d0375\msvcr90.dll 1187 INFO: Searching for file msvcp90.dll 1187 INFO: Found file C:\WINDOWS\WinSxS\x86_Microsoft.VC90.CRT_1fc8b3b9a1e18e3b_9.0.21022.8_x-ww_d08d0375\msvcp90.dll 1187 INFO: Searching for file msvcm90.dll 1187 INFO: Found file C:\WINDOWS\WinSxS\x86_Microsoft.VC90.CRT_1fc8b3b9a1e18e3b_9.0.21022.8_x-ww_d08d0375\msvcm90.dll 1266 INFO: Analyzing D:\Applications\Python\lib\site-packages\pyinstaller-2.1-py2.7.egg\PyInstaller\loader\_pyi_bootstrap.py 1266 INFO: Processing hook hook-os 1282 INFO: Processing hook hook-site 1296 INFO: Processing hook hook-encodings 1391 INFO: Processing hook hook-time 1407 INFO: Processing hook hook-cPickle 1468 INFO: Processing hook hook-_sre 1578 INFO: Processing hook hook-cStringIO 1671 INFO: Processing hook hook-codecs 2016 INFO: Processing hook hook-httplib 2016 INFO: Processing hook hook-email 2109 INFO: Processing hook hook-email.message 2312 WARNING: library python%s%s required via ctypes not found 2468 INFO: Processing hook hook-pydoc 2516 INFO: Analyzing D:\Applications\Python\lib\site-packages\pyinstaller-2.1-py2.7.egg\PyInstaller\loader\pyi_importers.py 2609 INFO: Analyzing D:\Applications\Python\lib\site-packages\pyinstaller-2.1-py2.7.egg\PyInstaller\loader\pyi_archive.py 2687 INFO: Analyzing D:\Applications\Python\lib\site-packages\pyinstaller-2.1-py2.7.egg\PyInstaller\loader\pyi_carchive.py 2782 INFO: Analyzing D:\Applications\Python\lib\site-packages\pyinstaller-2.1-py2.7.egg\PyInstaller\loader\pyi_os_path.py 2782 INFO: Analyzing b.py 2796 INFO: Processing hook hook-PySide 2875 INFO: Hidden import 'codecs' has been found otherwise 2875 INFO: Hidden import 'encodings' has been found otherwise 2875 INFO: Looking for run-time hooks 7766 INFO: Using Python library C:\WINDOWS\system32\python27.dll 7796 INFO: E:\true\wuk\app2\build\b\out00-Analysis.toc no change! 7796 INFO: checking PYZ 7812 INFO: checking PKG 7812 INFO: building because E:\true\wuk\app2\build\b\b.exe.manifest changed 7812 INFO: building PKG (CArchive) out00-PKG.pkg 7828 INFO: checking EXE 7843 INFO: rebuilding out00-EXE.toc because pkg is more recent 7843 INFO: building EXE from out00-EXE.toc 7843 INFO: Appending archive to EXE E:\true\wuk\app2\build\b\b.exe 7843 INFO: checking COLLECT 7843 INFO: building COLLECT out00-COLLECT.toc Use pyinstaller browser.py, and in the console window i got QFont::setPixelSize: Pixel size <= 0 (0) QSslSocket: cannot call unresolved function SSLv23_client_method QSslSocket: cannot call unresolved function SSL_CTX_new QSslSocket: cannot call unresolved function SSL_library_init QSslSocket: cannot call unresolved function ERR_get_error QSslSocket: cannot call unresolved function SSLv23_client_method QSslSocket: cannot call unresolved function SSL_CTX_new QSslSocket: cannot call unresolved function SSL_library_init QSslSocket: cannot call unresolved function ERR_get_error QSslSocket: cannot call unresolved function SSLv23_client_method QSslSocket: cannot call unresolved function SSL_CTX_new QSslSocket: cannot call unresolved function SSL_library_init QSslSocket: cannot call unresolved function ERR_get_error QSslSocket: cannot call unresolved function SSLv23_client_method QSslSocket: cannot call unresolved function SSL_CTX_new QSslSocket: cannot call unresolved function SSL_library_init QSslSocket: cannot call unresolved function ERR_get_error QFont::setPixelSize: Pixel size <= 0 (0)

  Read the article

• NHibernate which cache to use for WinForms application

  - by chiccodoro

  I have a C# WinForms application with a database backend (oracle) and use NHibernate for O/R mapping. I would like to reduce communication to the database as much as possible since the network in here is quite slow, so I read about second level caching. I found this quite good introduction, which lists the following available cache implementations. I'm wondering which implementation I should use for my application. The caching should be simple, it should not significantly slow down the first occurrence of a query, and it should not take much memory to load the implementing assemblies. (With NHibernate and Castle, the application already takes up to 80 MB of RAM!) Velocity: uses Microsoft Velocity which is a highly scalable in-memory application cache for all kinds of data. Prevalence: uses Bamboo.Prevalence as the cache provider. Bamboo.Prevalence is a .NET implementation of the object prevalence concept brought to life by Klaus Wuestefeld in Prevayler. Bamboo.Prevalence provides transparent object persistence to deterministic systems targeting the CLR. It offers persistent caching for smart client applications. SysCache: Uses System.Web.Caching.Cache as the cache provider. This means that you can rely on ASP.NET caching feature to understand how it works. SysCache2: Similar to NHibernate.Caches.SysCache, uses ASP.NET cache. This provider also supports SQL dependency-based expiration, meaning that it is possible to configure certain cache regions to automatically expire when the relevant data in the database changes. MemCache: uses memcached; memcached is a high-performance, distributed memory object caching system, generic in nature, but intended for use in speeding up dynamic web applications by alleviating database load. Basically a distributed hash table. SharedCache: high-performance, distributed and replicated memory object caching system. See here and here for more info My considerations so far were: Velocity seems quite heavyweight and overkill (the files totally take 467 KB of disk space, haven't measured the RAM it takes so far because I didn't manage to make it run, see below) Prevalence, at least in my first attempt, slowed down my query from ~0.5 secs to ~5 secs, and caching didn't work (see below) SysCache seems to be for ASP.NET, not for winforms. MemCache and SharedCache seem to be for distributed scenarios. Which one would you suggest me to use? There would also be a built-in implementation, which of course is very lightweight, but the referenced article tells me that I "(...) should never use this cache provider for production code but only for testing." Besides the question which fits best into my situation I also faced problems with applying them: Velocity complained that "dcacheClient" tag not specified in the application configuration file. Specify valid tag in configuration file," although I created an app.config file for the assembly and pasted the example from this article. Prevalence, as mentioned above, heavily slowed down my first query, and the next time the exact same query was executed, another select was sent to the database. Maybe I should "externalize" this topic into another post. I will do that if someone tells me it is absolutely unusual that a query is slowed down so much and he needs further details to help me.

  Read the article

• Why 32-bit color EGL configurations fail with EGL_BAD_MATCH on Moto Droid?

  - by Gilead

  I'm trying to figure out why certain EGL configurations cause eglMakeCurrent() call to return EGL_BAD_MATCH on Motorola Droid running Android 2.1u1. This is a full list of hardware-accelerated EGL configurations (those with EGL_CONFIG_CAVEAT == EGL_NONE) as there's a few others with EGL_CONFIG_CAVEAT == EGL_SLOW_CONFIG but those are backed by PixelFlinger 1.2 meaning they're using software renderer. ID: 0 RGB: 8, 8, 8 Alpha: 8 Depth: 24 Stencil: 8 // BAD MATCH ID: 1 RGB: 8, 8, 8 Alpha: 8 Depth: 0 Stencil: 0 // BAD MATCH ID: 2 RGB: 8, 8, 8 Alpha: 8 Depth: 24 Stencil: 8 // BAD MATCH ID: 3 RGB: 8, 8, 8 Alpha: 8 Depth: 24 Stencil: 8 // BAD MATCH ID: 4 RGB: 8, 8, 8 Alpha: 8 Depth: 0 Stencil: 0 // BAD MATCH ID: 5 RGB: 8, 8, 8 Alpha: 8 Depth: 24 Stencil: 8 // BAD MATCH ID: 6 RGB: 5, 6, 5 Alpha: 0 Depth: 24 Stencil: 8 ID: 7 RGB: 5, 6, 5 Alpha: 0 Depth: 0 Stencil: 0 ID: 8 RGB: 5, 6, 5 Alpha: 0 Depth: 24 Stencil: 8 Clearly, all configurations with 32-bit color depth fail and all 16-bit ones are OK but: 1. Why? 2. WHY?! :) 3. How do I tell which ones would fail before actually trying to use them? The code below is as simple as it can get. I put if (v[0] == 6) there to check different configs, normally they're chosen by half-clever config matcher :) private void createSurface(SurfaceHolder holder) { egl = (EGL10)EGLContext.getEGL(); eglDisplay = egl.eglGetDisplay(EGL10.EGL_DEFAULT_DISPLAY); egl.eglInitialize(eglDisplay, null); int[] numConfigs = new int[1]; egl.eglChooseConfig(eglDisplay, new int[] { EGL10.EGL_NONE }, null, 0, numConfigs); EGLConfig[] configs = new EGLConfig[numConfigs[0]]; egl.eglChooseConfig(eglDisplay, new int[] { EGL10.EGL_NONE }, configs, numConfigs[0], numConfigs); int[] v = new int[1]; for (EGLConfig c : configs) { egl.eglGetConfigAttrib(eglDisplay, c, EGL10.EGL_CONFIG_ID, v); if (v[0] == 6) { eglConfig = c; } } eglContext = egl.eglCreateContext(eglDisplay, eglConfig, EGL10.EGL_NO_CONTEXT, null); if (eglContext == null || eglContext == EGL10.EGL_NO_CONTEXT) { throw new RuntimeException("Unable to create EGL context"); } eglSurface = egl.eglCreateWindowSurface(eglDisplay, eglConfig, holder, null); if (eglSurface == null || eglSurface == EGL10.EGL_NO_SURFACE) { throw new RuntimeException("Unable to create EGL surface"); } if (!egl.eglMakeCurrent(eglDisplay, eglSurface, eglSurface, eglContext)) { throw new RuntimeException("Unable to make EGL current"); } gl = (GL10)eglContext.getGL(); }

  Read the article

• XmlSchema.read throws exception when an element is declared nillable

  - by G33kKahuna

  I have a simple schema that I am trying to read using XmlSchema.Read() method. I keep getting The 'nillable' attribute is not supported in this context Here is a simple code in C# XmlSchema schema = null; using (StreamReader reader = new StreamReader(<Path to Schema file name>) { schema = XmlSchema.Read(reader.BaseStream, null); } Below is the schema <xs:schema xmlns:b="http://schemas.microsoft.com/BizTalk/2003" xmlns="http://xyz.com.schema.bc.mySchema" attributeFormDefault="unqualified" elementFormDefault="qualified" targetNamespace="http://xyz.com.schema.bc.mySchema" xmlns:xs="http://www.w3.org/2001/XMLSchema"> <xs:element name="data"> <xs:complexType> <xs:sequence> <xs:element name="Component"> <xs:complexType> <xs:sequence> <xs:element minOccurs="1" maxOccurs="unbounded" name="row"> <xs:complexType> <xs:sequence> <xs:element name="changed_by" type="xs:string" nillable="true" /> <xs:element name="column_name" type="xs:string" nillable="true" /> <xs:element name="comment_text" type="xs:string" nillable="true" /> <xs:element name="is_approved" type="xs:string" nillable="true" /> <xs:element name="log_at" type="xs:dateTime" nillable="true" /> <xs:element name="new_val" type="xs:string" nillable="true" /> <xs:element name="old_val" type="xs:string" nillable="true" /> <xs:element name="person_id" type="xs:string" nillable="true" /> <xs:element name="poh_id" type="xs:string" nillable="true" /> <xs:element name="pol_id" type="xs:string" nillable="true" /> <xs:element name="search_name" type="xs:string" nillable="true" /> <xs:element name="unique_id" type="xs:integer" nillable="true" /> </xs:sequence> </xs:complexType> </xs:element> </xs:sequence> </xs:complexType> </xs:element> </xs:complexType> </xs:element> </xs:schema>

  Read the article

• iPhone MapKit problems: viewForAnnotation inconsistently setting pinColor?

  - by blackkettle

  Hi, I'm trying setup a map that displays different pin colors depending on the type/class of the location in question. I know this is a pretty common thing to do, but I'm having trouble getting the viewForAnnotation delegate to consistently update/set the pin color. I have a showThisLocation function that basically cycles through a list of AddressAnnotations and then based on the annotation class (bus stop, hospital, etc.) I set an if( myClass == 1){ [defaults setObject:@"1" forKey:@"currPinColor"]; [defaults synchronize]; NSLog(@"Should be %@!", [defaults objectForKey:@"currPinColor"]); } else if( myClass ==2 ){ [defaults setObject:@"2" forKey:@"currPinColor"]; [defaults synchronize]; NSLog(@"Should be %@!", [defaults objectForKey:@"currPinColor"]); } [_mapView addAnnotation:myCurrentAnnotation]; then my viewForAnnotation delegate looks like this, - (MKAnnotationView *) mapView:(MKMapView *)mapView viewForAnnotation:(id )annotation { if( annotation == mapView.userLocation ){ return nil; } NSUserDefaults *defaults = [NSUserDefaults standardUserDefaults]; MKPinAnnotationView *annView = nil; annView = (MKPinAnnotationView*)[mapView dequeueReusableAnnotationViewWithIdentifier:@"currentloc"]; if( annView == nil ){ annView = [[MKPinAnnotationView alloc] initWithAnnotation:annotation reuseIdentifier:@"currentloc"]; } annView.pinColor = [defaults integerForKey:@"currPinColor"]; NSLog(@"Pin color: %d", [defaults integerForKey:@"currPinColor"]); annView.animatesDrop=TRUE; annView.canShowCallout = YES; annView.calloutOffset = CGPointMake(-5, 5); return annView; } The problem is that, although the NSLog statements in the "if" block always confirm that the color has been set, the delegate sometimes but not always ends up with the correct color. I've also noticed that what generally happens is that the first search for a new location will set all pins to the last color in the "if" block, but search for the same location again will set the pins to the correct color. I suspect I am not supposed to usen NSUserDefaults in this way, but I also tried to create my own subclass for MKAnnotation which included an additional property "currentPinColor", and while this allowed me to set the "currentPinColor", when I tried to access the "currentPinColor from the delegate method, the compiler complained that it didn't know anything about "currentPinColor in connection with MKAnnotation. Fair enough I guess, but then I tried to revise the delegate method, - (MKAnnotationView *) mapView:(MKMapView *)mapView viewForAnnotation:(id )annotation instead of the default - (MKAnnotationView *) mapView:(MKMapView *)mapView viewForAnnotation:(id )annotation at which point the compiler complained that it didn't know anything about the protocol for MyCustomMKAnnotation in this delegate context. What is the proper way to set the delegate method and/or MyCustomMKAnnotation, or what is the appropriate way to achieve consistent pinColor settings. I'm just about out of ideas for things to try here.

  Read the article

• How do I use the gravity vector to correctly transform scene for augmented reality?

  - by gpdawson

  I'm trying figure out how to get an OpenGL specified object to be displayed correctly according to the device orientation (ie. according to the gravity vector from the accelerometer, and heading from compass). The GLGravity sample project has an example which is almost like this (despite ignoring heading), but it has some glitches. For example, the teapot jumps 180deg as the device viewing angle crosses the horizon, and it also rotates spuriously if you tilt the device from portrait into landscape. This is fine for the context of this app, as it just shows off an object and it doesn't matter that it does these things. But it means that the code just doesn't work when you attempt to emulate real life viewing of an OpenGL object according to the device's orientation. What happens is that it almost works, but the heading rotation you apply from the compass gets "corrupted" by the spurious additional rotations seen in the GLGravity example project. Can anyone provide sample code that shows how to adjust correctly for the device orientation (ie. gravity vector), or to fix the GLGravity example so that it doesn't include spurious heading changes? //Clear matrix to be used to rotate from the current referential to one based on the gravity vector bzero(matrix, sizeof(matrix)); matrix[3][3] = 1.0; //Setup first matrix column as gravity vector matrix[0][0] = accel[0] / length; matrix[0][1] = accel[1] / length; matrix[0][2] = accel[2] / length; //Setup second matrix column as an arbitrary vector in the plane perpendicular to the gravity vector {Gx, Gy, Gz} defined by by the equation "Gx * x + Gy * y + Gz * z = 0" in which we arbitrarily set x=0 and y=1 matrix[1][0] = 0.0; matrix[1][1] = 1.0; matrix[1][2] = -accel[1] / accel[2]; length = sqrtf(matrix[1][0] * matrix[1][0] + matrix[1][1] * matrix[1][1] + matrix[1][2] * matrix[1][2]); matrix[1][0] /= length; matrix[1][1] /= length; matrix[1][2] /= length; //Setup third matrix column as the cross product of the first two matrix[2][0] = matrix[0][1] * matrix[1][2] - matrix[0][2] * matrix[1][1]; matrix[2][1] = matrix[1][0] * matrix[0][2] - matrix[1][2] * matrix[0][0]; matrix[2][2] = matrix[0][0] * matrix[1][1] - matrix[0][1] * matrix[1][0]; //Finally load matrix glMultMatrixf((GLfloat*)matrix);

  Read the article

• ModalPopupExtender and validation problems

  - by Malachi

  The problem I am facing is that when there is validation on a page and I am trying to display a model pop-up, the pop-up is not getting displayed. And by using fire-bug I have noticed that an error is being thrown. The button that is used to display the pop-up has cause validation set to false so I am stuck as to what is causing the error. I have created a sample page to isolate the problem that I am having, any help would be greatly appreciated. The Error function () {Array.remove(Page_ValidationSummaries, document.getElementById("ValidationSummary1"));}(function () {var fn = function () {AjaxControlToolkit.ModalPopupBehavior.invokeViaServer("mpeSelectClient", true);Sys.Application.remove_load(fn);};Sys.Application.add_load(fn);}) is not a function http://localhost:1131/WebForm1.aspx Line 136 ASP <%@ Page Language="C#" AutoEventWireup="true" CodeBehind="WebForm1.aspx.cs" Inherits="CLIck10.WebForm1" %> <%@ Register Assembly="AjaxControlToolkit" Namespace="AjaxControlToolkit" TagPrefix="ajaxToolkit" %> <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml" > <head runat="server"> <title></title> </head> <body> <form id="form1" runat="server"> <asp:ScriptManager ID="ScriptManager1" runat="server"> </asp:ScriptManager> <div> <asp:Button ID="btnPush" runat="server" Text="Push" CausesValidation="false" onclick="btnPush_Click" /> <asp:TextBox ID="txtVal" runat="server" /> <asp:RequiredFieldValidator ID="RequiredFieldValidator1" runat="server" ControlToValidate="txtVal" ErrorMessage="RequiredFieldValidator" /> <asp:ValidationSummary ID="ValidationSummary1" runat="server" /> <asp:Panel ID="pnlSelectClient" Style="display: none" CssClass="box" runat="server"> <asp:UpdatePanel ID="upnlSelectClient" runat="server"> <ContentTemplate> <asp:Button ID="btnOK" runat="server" UseSubmitBehavior="true" Text="OK" CausesValidation="false" OnClick="btnOK_Click" /> <asp:Button ID="btnCancel" runat="server" Text="Cancel" CausesValidation="false" OnClick="btnCancel_Click" /> </ContentTemplate> </asp:UpdatePanel> </asp:Panel> <input id="popupDummy" runat="server" style="display:none" /> <ajaxToolkit:ModalPopupExtender ID="mpeSelectClient" runat="server" TargetControlID="popupDummy" PopupControlID="pnlSelectClient" OkControlID="popupDummy" BackgroundCssClass="modalBackground" CancelControlID="btnCancel" DropShadow="true" /> </div> </form> Code Behind using System; using System.Collections.Generic; using System.Linq; using System.Web; using System.Web.UI; using System.Web.UI.WebControls; namespace CLIck10 { public partial class WebForm1 : System.Web.UI.Page { protected void Page_Load(object sender, EventArgs e) { } protected void btnOK_Click(object sender, EventArgs e) { mpeSelectClient.Hide(); } protected void btnCancel_Click(object sender, EventArgs e) { mpeSelectClient.Hide(); } protected void btnPush_Click(object sender, EventArgs e) { mpeSelectClient.Show(); } } }

  Read the article

• How to debug nondeterministic access violation crash?

  - by Special Touch

  Our C#/COM/C++ application is crashing and I need help debugging it. Running with gflags enabled and WinDbg attached, we determined the crashes are caused by an access violation, but we haven't been able to narrow it down any more than that. We are not seeing the issue on all machines; there are a couple of machines that seem to reproduce the issue frequently but not deterministically. We have observed the application crash from simply switching away from the application (say, Alt-Tab) and then back. Output from WinDbg is below. We have been trying to systematically comment out areas of code that could be causing the problem, but we haven't had much success yet. Any suggestions on what debugging steps or tools we should try? !analyze -v EXCEPTION_RECORD: ffffffff -- (.exr 0xffffffffffffffff) ExceptionAddress: 1a584ff2 (+0x1a584ff1) ExceptionCode: c0000005 (Access violation) ExceptionFlags: 00000000 NumberParameters: 2 Parameter[0]: 00000000 Parameter[1]: 1a584ff2 Attempt to read from address 1a584ff2 PROCESS_NAME: ProcessFiles.exe ERROR_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s. EXCEPTION_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s. EXCEPTION_PARAMETER1: 00000000 EXCEPTION_PARAMETER2: 1a584ff2 READ_ADDRESS: 1a584ff2 FOLLOWUP_IP: Ed20+1a584ff1 1a584ff2 ?? ??? NTGLOBALFLAG: 2000000 APPLICATION_VERIFIER_FLAGS: 0 IP_MODULE_UNLOADED: Ed20+1a584ff1 1a584ff2 ?? ??? MANAGED_STACK: (TransitionMU) 0EC6F6F4 7B1D8CCE System_Windows_Forms_ni!System.Windows.Forms.Application+ComponentManager.System.Windows.Forms.UnsafeNativeMethods.IMsoComponentManager.FPushMessageLoop(Int32, Int32, Int32)+0x24e 0EC6F790 7B1D8937 System_Windows_Forms_ni!System.Windows.Forms.Application+ThreadContext.RunMessageLoopInner(Int32, System.Windows.Forms.ApplicationContext)+0x177 0EC6F7E4 7B1D8781 System_Windows_Forms_ni!System.Windows.Forms.Application+ThreadContext.RunMessageLoop(Int32, System.Windows.Forms.ApplicationContext)+0x61 0EC6F814 7B195911 System_Windows_Forms_ni!System.Windows.Forms.Application.Run(System.Windows.Forms.Form)+0x31 0EC6F828 0969D97A Extract_Utilities_Forms!Extract.Utilities.Forms.VerificationForm`1[[System.__Canon, mscorlib]].A(System.Object)+0x23a 0EC6F8C0 79A00EEE mscorlib_ni!System.Threading.ThreadHelper.ThreadStart_Context(System.Object)+0x72a25e 0EC6F8CC 792E019F mscorlib_ni!System.Threading.ExecutionContext.Run(System.Threading.ExecutionContext, System.Threading.ContextCallback, System.Object)+0x6f 0EC6F8E4 797DB48A mscorlib_ni!System.Threading.ThreadHelper.ThreadStart(System.Object)+0x4a (TransitionUM) LAST_CONTROL_TRANSFER: from 7e418734 to 1a584ff2 FAULTING_THREAD: ffffffff ADDITIONAL_DEBUG_TEXT: Followup set based on attribute [ip_not_executable] from Frame:[0] on thread:[e30] BUGCHECK_STR: APPLICATION_FAULT_BAD_INSTRUCTION_PTR_INVALID_POINTER_READ_WRONG_SYMBOLS_WINDOW_HOOK PRIMARY_PROBLEM_CLASS: BAD_INSTRUCTION_PTR DEFAULT_BUCKET_ID: BAD_INSTRUCTION_PTR STACK_TEXT: 7b1d8cce System_Windows_Forms_ni!System.Windows.Forms.Application+ComponentManager.System.Windows.Forms.UnsafeNativeMethods.IMsoComponentManager.FPushMessageLoop+0xc 7b1d8937 System_Windows_Forms_ni!System.Windows.Forms.Application+ThreadContext.RunMessageLoopInner+0x0 7b1d8781 System_Windows_Forms_ni!System.Windows.Forms.Application+ThreadContext.RunMessageLoop+0x0 7b195911 System_Windows_Forms_ni!System.Windows.Forms.Application.Run+0x31 0969d97a Extract_Utilities_Forms!Extract.Utilities.Forms.VerificationForm`1[[System.__Canon, mscorlib]].A+0x23a 79a00eee mscorlib_ni!System.Threading.ThreadHelper.ThreadStart_Context+0x72a25e 792e019f mscorlib_ni!System.Threading.ExecutionContext.Run+0x6f 797db48a mscorlib_ni!System.Threading.ThreadHelper.ThreadStart+0x4a STACK_COMMAND: .ecxr ; ~~[e30] ; .frame 0 ; ** Pseudo Context ** ; kb FAILED_INSTRUCTION_ADDRESS: Ed20+1a584ff1 1a584ff2 ?? ??? SYMBOL_NAME: Ed20 FOLLOWUP_NAME: MachineOwner MODULE_NAME: Ed20 IMAGE_NAME: Ed20 DEBUG_FLR_IMAGE_TIMESTAMP: 0 FAILURE_BUCKET_ID: BAD_INSTRUCTION_PTR_c0000005_Ed20!Unloaded BUCKET_ID: APPLICATION_FAULT_BAD_INSTRUCTION_PTR_INVALID_POINTER_READ_WRONG_SYMBOLS_WINDOW_HOOK_BAD_IP_Ed20 Followup: MachineOwner

  Read the article

• Unable to retrieve information form HP-UX pst_status object

  - by bogertron

  I am attempting to get process information by using the HP-UX C/C++ library. After scouring the internet, I have discovered that HP-UX has the pstat.h header file which allows programmers to retrieve the process information. After attempting to understand code from the internet hp website, I attempted to create a little test sample to comprehend what the code does. I attempted to use example 3, however, I ran into several issues. The first issue came when I attempted to execute the following line of code: (void)printf("pid is %d, command is %s\n", pst[i].pst_pid, pst[i].pst_ucomm); When I attempted to print the string, I hit a memory fault. So I decided to attempt to see what the string is and came up with the following: #include <sys/param.h> #include <sys/pstat.h> #include <sys/unistd.h> #include <string.h> int main(int argc, char** argv) { #define BURST ((size_t)10) struct pst_status pst[BURST]; int i, count; int idx = 0; /* index within the context */ int index = 0; /* loop until count == 0, will occur all have been returned */ while ((count=pstat_getproc(pst, sizeof(pst[0]),BURST,idx))>0) { index = 0; printf("index: %d", index); /* got count (max of BURST) this time. process them */ while (pst[i].pst_ucomm[index] != '\0') { printf("%c", pst[i].pst_ucomm[index]); index++; } printf("\n"); for (i = 0; i < count; i++) { printf("pid is %d, command is \n", pst[i].pst_pid); } /* * now go back and do it again, using the next index after * the current 'burst' */ idx = pst[count-1].pst_idx + 1; } if (count == -1) perror("pstat_getproc()"); #undef BURST } Unfortunately, what happens is that I get the first process printed, then pid is 2, command is pid is 2, command is pid is 2, command is... I know that I must be doing something foolish since my C/C++ skills are not that great, but I cannot figure out what the issue is since the code is largely copied from the hp website. So here's the question(s) for clarity: 1. Why can't printf("%s", pst[i].pst_ucomm); handle strings? 2. Why can't I iterate over the processes in the system? Any help is greatly appreciated.

  Read the article

• WPF UserControl Style results in error message

  - by Didier

  Hi I'm new in WPF so I try to create a WPF UserControl. My problem is about the style of the user control I've Created. On a design time I got this error message Can only base on a Style with target type that is base type 'RichTextBox'. at System.Windows.Style.Seal() at System.Windows.StyleHelper.UpdateStyleCache(FrameworkElement fe, FrameworkContentElement fce, Style oldStyle, Style newStyle, Style& styleCache) at System.Windows.FrameworkElement.OnStyleChanged(DependencyObject d, DependencyPropertyChangedEventArgs e) at System.Windows.DependencyObject.OnPropertyChanged(DependencyPropertyChangedEventArgs e) at System.Windows.FrameworkElement.OnPropertyChanged(DependencyPropertyChangedEventArgs e) at System.Windows.DependencyObject.NotifyPropertyChange(DependencyPropertyChangedEventArgs args) at System.Windows.DependencyObject.UpdateEffectiveValue(EntryIndex entryIndex, DependencyProperty dp, PropertyMetadata metadata, EffectiveValueEntry oldEntry, EffectiveValueEntry& newEntry, Boolean coerceWithDeferredReference, OperationType operationType) at System.Windows.DependencyObject.InvalidateProperty(DependencyProperty dp) at System.Windows.FrameworkElement.UpdateStyleProperty() at System.Windows.TreeWalkHelper.InvalidateStyleAndReferences(DependencyObject d, ResourcesChangeInfo info, Boolean containsTypeOfKey) at System.Windows.TreeWalkHelper.OnResourcesChanged(DependencyObject d, ResourcesChangeInfo info, Boolean raiseResourceChangedEvent) at System.Windows.TreeWalkHelper.OnResourcesChangedCallback(DependencyObject d, ResourcesChangeInfo info) at System.Windows.DescendentsWalker1._VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.VisitNode(FrameworkElement fe) at System.Windows.DescendentsWalker1.VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.WalkLogicalChildren(FrameworkElement feParent, FrameworkContentElement fceParent, IEnumerator logicalChildren) at System.Windows.DescendentsWalker1.WalkFrameworkElementLogicalThenVisualChildren(FrameworkElement feParent, Boolean hasLogicalChildren) at System.Windows.DescendentsWalker1.IterateChildren(DependencyObject d) at System.Windows.DescendentsWalker1._VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.VisitNode(FrameworkElement fe) at System.Windows.DescendentsWalker1.VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.WalkLogicalChildren(FrameworkElement feParent, FrameworkContentElement fceParent, IEnumerator logicalChildren) at System.Windows.DescendentsWalker1.WalkFrameworkElementLogicalThenVisualChildren(FrameworkElement feParent, Boolean hasLogicalChildren) at System.Windows.DescendentsWalker1.IterateChildren(DependencyObject d) at System.Windows.DescendentsWalker1._VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.VisitNode(FrameworkElement fe) at System.Windows.DescendentsWalker1.VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.WalkLogicalChildren(FrameworkElement feParent, FrameworkContentElement fceParent, IEnumerator logicalChildren) at System.Windows.DescendentsWalker1.WalkFrameworkElementLogicalThenVisualChildren(FrameworkElement feParent, Boolean hasLogicalChildren) at System.Windows.DescendentsWalker1.IterateChildren(DependencyObject d) at System.Windows.DescendentsWalker1._VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.VisitNode(FrameworkElement fe) at System.Windows.DescendentsWalker1.VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.WalkLogicalChildren(FrameworkElement feParent, FrameworkContentElement fceParent, IEnumerator logicalChildren) at System.Windows.DescendentsWalker1.WalkFrameworkElementLogicalThenVisualChildren(FrameworkElement feParent, Boolean hasLogicalChildren) at System.Windows.DescendentsWalker1.IterateChildren(DependencyObject d) at System.Windows.DescendentsWalker1._VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.VisitNode(FrameworkElement fe) at System.Windows.DescendentsWalker1.VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.WalkLogicalChildren(FrameworkElement feParent, FrameworkContentElement fceParent, IEnumerator logicalChildren) at System.Windows.DescendentsWalker1.WalkFrameworkElementLogicalThenVisualChildren(FrameworkElement feParent, Boolean hasLogicalChildren) at System.Windows.DescendentsWalker1.IterateChildren(DependencyObject d) at System.Windows.DescendentsWalker1._VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.VisitNode(FrameworkElement fe) at System.Windows.DescendentsWalker1.VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.WalkLogicalChildren(FrameworkElement feParent, FrameworkContentElement fceParent, IEnumerator logicalChildren) at System.Windows.DescendentsWalker1.WalkFrameworkElementLogicalThenVisualChildren(FrameworkElement feParent, Boolean hasLogicalChildren) at System.Windows.DescendentsWalker1.IterateChildren(DependencyObject d) at System.Windows.DescendentsWalker1._VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.VisitNode(FrameworkElement fe) at System.Windows.DescendentsWalker1.VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.WalkLogicalChildren(FrameworkElement feParent, FrameworkContentElement fceParent, IEnumerator logicalChildren) at System.Windows.DescendentsWalker1.WalkFrameworkElementLogicalThenVisualChildren(FrameworkElement feParent, Boolean hasLogicalChildren) at System.Windows.DescendentsWalker1.IterateChildren(DependencyObject d) at System.Windows.DescendentsWalker1._VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.VisitNode(FrameworkElement fe) at System.Windows.DescendentsWalker1.VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.WalkLogicalChildren(FrameworkElement feParent, FrameworkContentElement fceParent, IEnumerator logicalChildren) at System.Windows.DescendentsWalker1.WalkFrameworkElementLogicalThenVisualChildren(FrameworkElement feParent, Boolean hasLogicalChildren) at System.Windows.DescendentsWalker1.IterateChildren(DependencyObject d) at System.Windows.DescendentsWalker1._VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.VisitNode(FrameworkElement fe) at System.Windows.DescendentsWalker1.VisitNode(DependencyObject d) at System.Windows.DescendentsWalker1.WalkLogicalChildren(FrameworkElement feParent, FrameworkContentElement fceParent, IEnumerator logicalChildren) at System.Windows.DescendentsWalker1.WalkFrameworkElementLogicalThenVisualChildren(FrameworkElement feParent, Boolean hasLogicalChildren) at System.Windows.DescendentsWalker1.IterateChildren(DependencyObject d) at System.Windows.DescendentsWalker`1.StartWalk(DependencyObject startNode, Boolean skipStartNode) at System.Windows.TreeWalkHelper.InvalidateOnResourcesChange(FrameworkElement fe, FrameworkContentElement fce, ResourcesChangeInfo info) at System.Windows.ResourceDictionary.NotifyOwners(ResourcesChangeInfo info) at System.Windows.ResourceDictionary.EndInit() at MS.Internal.Host.Designer.OnAppResourcesChanged(Object sender, EventArgs e) at MS.Internal.Host.Designer.get_View() at MS.Internal.Designer.VSDesigner.Load() at MS.Internal.Designer.VSIsolatedDesigner.VSIsolatedView.Load() at MS.Internal.Designer.VSIsolatedDesigner.VSIsolatedDesignerFactory.Load(IsolatedView view) at MS.Internal.Host.Isolation.IsolatedDesigner.BootstrapProxy.LoadDesigner(IsolatedDesignerFactory factory, IsolatedView view) at MS.Internal.Host.Isolation.IsolatedDesigner.BootstrapProxy.LoadDesigner(IsolatedDesignerFactory factory, IsolatedView view) at MS.Internal.Host.Isolation.IsolatedDesigner.Load() at MS.Internal.Designer.DesignerPane.LoadDesignerView() And at a run time An error Message type XamlParseException Occurs and the message is: Cannot create instance of 'RichTextBox' defined in assembly 'PresentationFramework, Version=3.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35'. Can only base on a Style with target type that is base type 'RichTextBox'. Error at object 'System.Windows.Controls.Grid' in markup file 'NameSpace;component/usercontrols /myusercontrol.xaml' Line 125 Position 14. My user control have 3 richtextboxes 1 textbox and 3 dropdownlist and about 10 buttons. I think The problem is about to define the style of my user control, can anyone help me to do this. Thanks

  Read the article

• MSSQL: How to copy a file (pdf, doc, txt...) stored in a varbinary(max) field to a file in a CLR sto

  - by user193655

  I ask this question as a followup of this question. A solution that uses bcp and xp_cmdshell, that is not my desired solution, has been posted here: stackoverflow.com/questions/828749/ms-sql-server-2005-write-varbinary-to-file-system (sorry i cannot post a second hyperlink since my reputation is les than 10). I am new to c# (since I am a Delphi developer) anyway I was able to create a simple CLR stored procedures by following a tutorial. My task is to move a file from the client file system to the server file system (the server can be accessed using remote IP, so I cannot use a shared folder as destination, this is why I need a CLR stored procedure). So I plan to: 1) store from Delphi the file in a varbinary(max) column of a temporary table 2) call the CLR stored procedure to create a file at the desired path using the data contained in the varbinary(max) field Imagine I need to move C:\MyFile.pdf to Z:\MyFile.pdf, where C: is a harddrive on local system and Z: is an harddrive on the server. I provide the code below (not working) that someone can modify to make it work? Here I suppose to have a table called MyTable with two fields: ID (int) and DATA (varbinary(max)). Please note it doesn't make a difference if the table is a real temporary table or just a table where I temporarly store the data. I would appreciate if some exception handling code is there (so that I can manage an "impossible to save file" exception). I would like to be able to write a new file or overwrite the file if already existing. [Microsoft.SqlServer.Server.SqlProcedure] public static void VarbinaryToFile(int TableId) { using (SqlConnection connection = new SqlConnection("context connection=true")) { connection.Open(); SqlCommand command = new SqlCommand("select data from mytable where ID = @TableId", connection); command.Parameters.AddWithValue("@TableId", TableId); // This was the sample code I found to run a query //SqlContext.Pipe.ExecuteAndSend(command); // instead I need something like this (THIS IS META_SYNTAX!!!): SqlContext.Pipe.ResultAsStream.SaveToFile('z:\MyFile.pdf'); } } (one subquestion is: is this approach coorect or there is a way to directly pass the data to the CLR stored procedure so I don't need to use a temp table?) If the subquestion's answer is No, could you describe the approach of avoiding a temp table? So is there a better way then the one I describe above (=temp table + Stored procedure)? A way to directly pass the dataastream from the client application to the CLR stored procedure? (my files can be any size but also very big)

  Read the article

• Defining a ContextMenu in a DataGridRow style

  - by Brent

  I'm trying to clean up some of my xaml in my views by moving a lot of the DataGrid styles into a ResourceDictionary. One of the things I'd like to move is the ContextMenu that is bound to some commands in the ViewModel. However, when I move the context menu to the ResourceDictionary, the commands are are never firing anymore, and I can't figure out why. I've defined the ContextMenu in the DataGridRow style so that when the user right clicks on the columnheader, no ContextMenu is shown... it will only be shown they right click on a row. Am I doing something wrong here? FYI I'm using VS 2010 RTM if that makes a difference. <Style x:Key="DataGridRowStyle" TargetType="{x:Type DataGridRow}"> <Setter Property="Height" Value="20"/> <Setter Property="ContextMenu"> <Setter.Value> <ContextMenu> <MenuItem Header="New" Command="{Binding RelativeSource={RelativeSource AncestorType=DataGrid}, Path=DataContext.NewCommand}"> <MenuItem.Icon> <Image Source="/Images/DocumentWhite(32N).png" Width="16" Height="16"/> </MenuItem.Icon> </MenuItem> <MenuItem Header="Open" Command="{Binding RelativeSource={RelativeSource AncestorType=DataGrid}, Path=DataContext.OpenCommand}"> <MenuItem.Icon> <Image Source="/Images/FolderOpenYellow(32N).png" Width="16" Height="16"/> </MenuItem.Icon> </MenuItem> <MenuItem Header="Delete" Command="{Binding RelativeSource={RelativeSource AncestorType=DataGrid}, Path=DataContext.DeleteCommand}"> <MenuItem.Icon> <Image Source="/Images/Delete(32N).png" Width="16" Height="16"/> </MenuItem.Icon> </MenuItem> </ContextMenu> </Setter.Value> </Setter> <Style.Triggers> <Trigger Property="IsMouseOver" Value="True"> <Setter Property="Background" Value="{StaticResource hoverGradient}"/> </Trigger> <Trigger Property="IsSelected" Value="True"> <Setter Property="Background" Value="{StaticResource BtnOverFill}"/> </Trigger> </Style.Triggers> </Style>

  Read the article

• WCF errors in VS 2010/.Net 4 using sample publish/subscribe app from IDesign website

  - by Bill

  I am attempting to compile/run a sample WCF application from Juval Lowy's website (author of Programming WCF Services & founder of IDesign). The application is an example of a publish/subscribe 'traffic-light' application that requires using VS 2010/.Net 4. This is my first attempt at using anything other than VS 2008/Net 3.5. Initially I recieved the following binding error: "Configuration binding extension 'system.serviceModel/bindings/ netOnewayRelayBinding' could not be found." This error appeared to be resolved by amending the .Net 4 machine.config file, to incorporate the following references from the .Net 2 machine.config file. <xml> <bindingElementExtensions> <add name="tcpRelayTransport" type="Microsoft.ServiceBus.Configuration.TcpRelayTransportElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="httpRelayTransport" type="Microsoft.ServiceBus.Configuration.HttpRelayTransportElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="httpsRelayTransport" type="Microsoft.ServiceBus.Configuration.HttpsRelayTransportElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="onewayRelayTransport" type="Microsoft.ServiceBus.Configuration.RelayedOnewayTransportElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="webMessageEncoding" type="System.ServiceModel.Configuration.WebMessageEncodingElement, System.ServiceModel.Web, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35"/> <add name="context" type="System.ServiceModel.Configuration.ContextBindingElementExtensionElement, System.ServiceModel, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089"/> <add name="byteStreamMessageEncoding" type="System.ServiceModel.Configuration.ByteStreamMessageEncodingElement, System.ServiceModel.Channels, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35"/> <add name="discoveryClient" type="System.ServiceModel.Discovery.Configuration.DiscoveryClientElement, System.ServiceModel.Discovery, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35"/> </bindingElementExtensions> <bindingExtensions> <add name="webHttpBinding" type="System.ServiceModel.Configuration.WebHttpBindingCollectionElement, System.ServiceModel.Web, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35"/> <add name="basicHttpContextBinding" type="System.ServiceModel.Configuration.BasicHttpContextBindingCollectionElement, System.ServiceModel, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089"/> <add name="basicHttpRelayBinding" type="Microsoft.ServiceBus.Configuration.BasicHttpRelayBindingCollectionElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="webHttpRelayBinding" type="Microsoft.ServiceBus.Configuration.WebHttpRelayBindingCollectionElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="ws2007HttpRelayBinding" type="Microsoft.ServiceBus.Configuration.WS2007HttpRelayBindingCollectionElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="netTcpRelayBinding" type="Microsoft.ServiceBus.Configuration.NetTcpRelayBindingCollectionElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="netOnewayRelayBinding" type="Microsoft.ServiceBus.Configuration.NetOnewayRelayBindingCollectionElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="netEventRelayBinding" type="Microsoft.ServiceBus.Configuration.NetEventRelayBindingCollectionElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35"/> <add name="wsHttpContextBinding" type="System.ServiceModel.Configuration.WSHttpContextBindingCollectionElement, System.ServiceModel, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089"/> <add name="netTcpContextBinding" type="System.ServiceModel.Configuration.NetTcpContextBindingCollectionElement, System.ServiceModel, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089"/> </bindingExtensions> Unfortunately running the application results in the following security error: An error occurred creating the configuration section handler for system.serviceModel/client: That assembly does not allow partially trusted callers. (\TrafficLights\TrafficController\bin\Debug\TrafficController.vshost.exe.Config line 4) The sample source code is available for download at the following link: http://www.idesign.net/idesign/DesktopDefault.aspx?tabindex=-1&tabid=19&download=226 I know that Juval's code is not at fault here and that it must be something I'm doing wrong with my VS 2010 configuration. I have not been able to find a solution online. Could someone please steer me in the right direction as to how best to deal with this issue?

  Read the article

• UIViewAnimation done by a UIViewController belonging to a UINavigationController?

  - by RickiG

  Hi I have an UINavigationController which the user navigates with. When pushing a specific UIViewController onto the navigation stack, a "settings" button appear in the navigationBar. When the user clicks this button I would like to flip the current view/controller, i.e. everything on screen, including the navigationBar, over to a settings view. So I have a SettingsViewController which I would like to flip to from my CurrentViewController that lives on a navigationController stack. I get all kinds of strange behavior trying to do this, the UIViews belonging to the SettingsViewController will start to animate, sliding into place, the navigationButtons moves around, nothing acts as I would think. -(void)settingsHandler { SettingViewController *settingsView = [[SettingViewController alloc] init]; [UIView beginAnimations:nil context:nil]; [UIView setAnimationDuration:1.0]; [UIView setAnimationTransition:UIViewAnimationTransitionFlipFromRight forView:self.navigationController.view cache:YES]; [self.navigationController.view addSubview:settingsView.view]; [UIView commitAnimations]; } The above results in the views flipping correctly, but the subviews of the SettingsViewController are all positioned in (0, 0) and after the transition, they 'snap' into place? Is it because I instantiate and add my subviews in viewDidLoad, like this? - (void)viewDidLoad { UIImageView *imageBg = [[UIImageView alloc] initWithFrame:CGRectMake(0.0f, 0.0f, 320.0f, 460.0f)]; [imageBg setImage:[UIImage imageNamed:@"background.png"]]; [self.view addSubview:imageBg]; [imageBg release]; SettingsSubview *switchView = [[SettingsSubview alloc] initWithFrame:CGRectMake(0.0f, 0.0f, 320.0f, 460.0f)]; [self.view addSubview:switchView]; [switchView release]; [super viewDidLoad]; } 1: How should I correctly do the "flip" transition, from within the UIViewController in the UINavigationController, to a new UIViewController and subsequently from the new UIViewController and back to the "original" UIViewController residing on the UINavigationControllers stack? 2: Should I use a different approach, than the "viewDidLoad" method, when instantiating and adding subviews to a UIViewController? -question 2 is more of a "best practice" thing. I have seen different ways of doing it and I am having trouble either finding or understanding the life-cycle documentation and the different threads and posts on the subject. I am missing the "best practice" examples. Thank You very much for any help given:)

  Read the article

< Previous Page | 428 429 430 431 432 433 434 435 436 437 438 439  | Next Page >