Search Results

Search found 14745 results on 590 pages for 'setting'.

Page 432/590 | < Previous Page | 428 429 430 431 432 433 434 435 436 437 438 439  | Next Page >

• How to connect 2 routers (Asmax and D-link) RJ11 vs RJ45 issue

  - by piobyz

  I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

  Read the article

• SYS-5016T-MTFB will not POST without manual assistance (Motherboard: X8STi-F)

  - by Dan

  I have a Supermicro 5016T-MTFB 1U server which I am in the process of setting up, but it has a really strange problem. When the system is powered on it will not POST until I press the reset button a few times, followed by pressing the delete key on the keyboard to "wake it up". If I power it on and do nothing, the fans spin up but nothing else happens at all. After pressing the reset button once, the red "overheat" light comes on and blinks which is supposed to indicate a fan failure - but all the fans are working. Pressing reset again usually stops the blinking, and the system starts the normal POST routine but it will not actually get to the bios screen unless I press delete. If I don't press delete, it just continues to hang. After pressing delete it will take me into the bios setup screen, if I exit without saving changes I can boot the system normally. I was able to successfully install Linux with no trouble...but upon rebooting the same problem happened again. This board has integrated IPMI which I thought was the problem, so I disabled it via the jumper on the board. Did not help. Each time this system powers on, it goes on for a second, then turns off again for another second, then turns back on again. I don't know why it does that. Here is what I put in the system: 1 x Xeon E5630 (Nehalem) 80W TDP (it's not overheating, CPU temps stay under 40 degrees C) 2 x Kingston 2GB x 3 DDR3-1066 Memory ECC, unbuffered, unregistered (kvr1066d3e7sk3/6g) 1 x Intel X25-M 160 GB 2 x Western Digital RE3 1TB

  Read the article

• Problems with image/file upload in MediaWiki on Windows 2008 Server R2, using wrong temp directory

  - by Lasse V. Karlsen

  I have installed MediaWiki 1.15.2 under IIS as per the MediaWiki installation instructions for Windows 2008 Server. I have configured PHP to use a specific temp directory: upload_tmp_dir="C:\php\uploadtemp" I have specified that MediaWiki is allowed to upload: $wgEnableUploads = true; But when I try to upload an image, I get this error message in my browser: Internal error Could not find file "C:\Windows\Temp\php1AEA.tmp". Retrying will simply give me a new filename, but in the same location. The directory does not have any php* files in it, but since they're "temporary", they might be gone in a flash before Windows Explorer is able to show them so that might be a red herring. I've googled for this, and the most promising lead I found was on this page: Image upload problem - Is this bug fixed?, but since the text says "a bugfix was posted on the bug-report page", but provides no link to which bug page this relates to (php or mediawiki) nor the actual bug report, I've not found conclusively the bug report in question so that didn't help me much. Lots of pages indicates that this is a permission issue, so I tried setting permissions on c:\windows\temp as Modify by Everyone, still no dice. I tried changing the two system environment variables TEMP and TMP to point to C:\Temp instead, but MediaWiki still complains about not finding the file in C:\Windows\Temp. Note that I don't care a lot about where the files will actually be stored temporarily, so c:\windows\temp is fine by me. I do, however, care about them actually being uploaded correctly. Does anyone know of a fix, have any leads I can follow, or whatnot? The server is running Windows 2008 Server R2, all patches installed, and the PHP installed is 5.3.2, using IIS FastCGI.

  Read the article

• Can't access my accelerated hard disk from msdos after installing linux on ssd cache

  - by Chibueze Opata

  I mistakenly installed Linux Mint on my ssd (forgot my PC actually came with one), when it detected a ~31GiB disk that it wanted to install to, I was a bit confused since I had brought out 30Gb in my primary disk for it, but I clicked continue. After installation, I tried to boot back into my Windows and it brought out some Intel Raid Disk Utility stuff saying I should disable acceleration on a disk something couldn't be found, I canceled it but whatever I tried, recovery tools, setups etc, I couldn't just access the drive which was apparently using the SSD as cache. Since then I've been stuck. I tried setting the 'raid' flag to the disk from 'gParted', still I couldn't. I tried the diskraid utility from windows recover disk, it said it couldn't detect any raid, diskpart sees the partition but doesn't see the volume, when I remove the raid flag, it sees the volume as one of raw type, and I can't access anything. I can however mount the drive from terminal in Mint and access my files, but I don't have any backup media at the moment so I can do a factory re-install. Please how do I go about solving the issue, precisely I would like to know how to boot into the drive again. Thanks!

  Read the article

• Excel file growing huge (>150 MB)

  - by Josh

  There is one particular Excel file that is used by a number of employees at my company. It is edited from both Excel 2003 and 2007, with the "Sharing" feature turned on to allow multiple writers at once. The file has a decent amount of data on several sheets with some basic formatting, and used to be about 6MB, which seems reasonable for its content. But after a few weeks of editing, the file grew to 10, then 20 MB, and eventually skyrocketed to more than 150 MB, even though it still has about the same amount of data as before. It now takes 5-10 minutes to open it, and that much time again to save it. The first time this happened, I copied the content of each sheet into a new, blank workbook, and saved the new workbook; this brought it back down to about 6MB. Now, it has blown up again. The workbook uses the "Data Validation" feature to limit the values in certain columns to the contents of a few named ranges. Copying all the data into a new workbook means re-setting up all the data validation, which is a pain and not something that we want to do every month. As a troubleshooting step, I tried saving the file in "XML Spreadsheet 2003" format, hoping to get some insight into what was being stored. Sure enough, the file was almost a gig, and almost all of the 10 million lines look like this: <NamedCell ss:Name="Z_21D5114F_E50C_46AC_AA4F_C3FF540C717F_.wvu.FilterData"/> <NamedCell ss:Name="Z_1EE2BA5E_3011_4F9A_8ACD_E58835250FC4_.wvu.FilterData"/> <NamedCell ss:Name="Z_1E3BDCEA_6A72_4ECC_BF4F_7B03CC66181E_.wvu.FilterData"/> I've seen a few VBScripts online to manage and enumerate named cells that are hidden in Excel's built-in interface, though I wonder how they'd handle my 10 million named cells. What I really need, though, is an understanding of why this keeps happening. What actions in excel could be causing this?

  Read the article

• Why is .htaccess not allowed in a directory but is allowed in another?

  - by JD Isaacks

  I have apache2 installed on ubuntu 10.4 inside my var/www/ directory [amung others] I have a cakephp and a dvdcatalog directories. Each of which have CakePHP 1.3 installed. I can access them both via localhost/cakephp and localhost/dvdcatalog But the dvdcatalog shows up with no css styling. They both have these files: /var/www/cakephp/app/webroot/css/cake.generic.css /var/www/dvdcatalog/app/webroot/css/cake.generic.css But when I go to http://localhost/cakephp/css/cake.generic.css it sees the file but it does not see the file when I go to http://localhost/dvdcatalog/css/cake.generic.css I think this means the cakephp folder is able to use .htaccess and the dvdcatalog is not. I setup the cakephp directory last month when I was following in the blog tutorial. I am setting up the dvdcatalog directory now for a different tutorial. So I am not sure if I am missing a step. in my /etc/apache2/apache2.conf file I have this: <Directory "/var/www/*"> Order allow,deny Allow from all AllowOverride All </Directory> Which I thought gave .htaccesss to all. Does anyone have any ideas what the problem is?

  Read the article

• Configuration for Router Behind Uverse 2Wire

  - by Nori

  I have a 2Wire Uverse router(RG). I'm not particularly fond of it and want to use it as a modem only. I have a Linksys router with Tomato firmware on it and want that to be configured as the router. Most of the "guides" I've seen in my searches has been to enable DMZ Plus mode, but I don't see a way to make that work while my router has a static IP address. I played with it for quite some time yesterday and didn't see a way to get it to work. Then I ran across a setting in broadband for configuring another network. I played with that for a little bit but ran out of time and couldn't get it to work. So my question is for anyone out there who has Uverse and successfully setup a Tomato based firmware router behind the RG. How did you get it configured? I'm sure if I continued playing with it I could get it to work, but if someone out there already has it working then that would make my life easier. Thoughts? Thanks.

  Read the article

• ghc6 install trouble: hGetContents: invalid argument (invalid UTF-8 byte sequence)

  - by olimay

  Having trouble installing ghc6 on Ubuntu Maverick via apt. Here's what seems to be the relevant error that comes up when I try to (apt-get|aptitude) install ghc6: A package failed to install. Trying to recover: Setting up ghc6 (6.12.1-13ubuntu1) ... ghc-pkg: /home/opm/.ghc/i386-linux-6.12.1/package.conf.d/unix-compat-0.2-edefa7bced91ebe610d455bab466e200.conf: hGetContents: invalid argument (invalid UTF-8 byte sequence) (Here's the full output, if you're interested: http://paste.ubuntu.com/566475/ ) This still happens after apt-get clean and apt-get update. My searching around has not really helped me understand what's going on, except that it might be caused by a mismatch in locale. So, here's the output of locale too: LANG=en_US.utf8 LANGUAGE=en_US:en LC_CTYPE="en_US.utf8" LC_NUMERIC="en_US.utf8" LC_TIME="en_US.utf8" LC_COLLATE="en_US.utf8" LC_MONETARY="en_US.utf8" LC_MESSAGES="en_US.utf8" LC_PAPER="en_US.utf8" LC_NAME="en_US.utf8" LC_ADDRESS="en_US.utf8" LC_TELEPHONE="en_US.utf8" LC_MEASUREMENT="en_US.utf8" LC_IDENTIFICATION="en_US.utf8" LC_ALL= Any ideas? Additional background: this all seems very strange to me, because I used to have ghc6 installed correctly--I use XMonad as my main window manager most of the time. I tried to install haskell-platform (through apt), which failed and told me that there was something wrong with ghc6, and so I reinstalled ghc6 and began to get the above error message.

  Read the article

• Postfix selective header_checks: smtpd_relay_restrictions vs. smtpd_recipient_restrictions

  - by luke

  Some of my customers implemented commercial software that violate email-RFCs such that we have had to relax our header checks. In consequence, we receive more spam. Prolog: I know the domains (customer.com) and IP-addresses (a.b.c.d/C) these emails come from Kind request for help: Is it possible to setup one Postfix (2.11) instance on Linux such that: It applies only some header checks for emails from .*@customer.com But applies all header checks for all other email sources? I thought of a combination of mynetworks that includes the subnet a.b.c.d/C in smtpd_recipient_restrictions -- allowing all these messages through -- and simultaneously avoid an open-relay with smtpd_relay_restrictions. However, this has not worked out as expected. Any idea or help is highly appreciated. Thanks in advance. Luke ==EDIT== For the current issue, I solved the problem by prepending REDIRECTs to header_checks as follows: /^received: from.*customer.com.*by mail.own.com.*for.*luke@own.*/ REDIRECT [email protected] This works so far as neeeded. Irrespective thereof, I am still looking for a postfix configuration that would turn this text-based setting into an IP-Address-Range based forwarding rule.... Thanks. Luke

  Read the article

• Cisco QoS Guidence

  - by Kyle Brandt

  I have a 10M connection to the internet that is hooked into a 100M port. I am getting started with QoS, and am hopping for a little guidance on setting it up on a Cisco 3825 router. Right now I am going forward with the idea that I have to implement it on my router, and the provider can't provide QoS for me. How I envision it working is that the QoS will drop or queue packets on my router and that will help prevent a situation where the provider has to start dropping a lot of packets. Right now all I am tasked with is making sure that one of the 3 LANs gets a certain slice (say 3M for Gig Lan1) of the 10M internet connection (But ideally this will be more flexible in the Future). 10M Internet on 100M port on HWIC-4ESW +-----------------------+ | | Gig Lan1 | Cisco 3825 | Lan3 on HWIC-4ESW | | +-----------------------+ Gig Lan2 I need to learn more about QoS, but having a target technology and maybe example configuration will help me wrap my head around the reading I am doing a little more. Which Cisco QoS Technology do you recommend for this particular situation? Have a basic sample config of how this might work? Right now the 10M line is not congested, so this more to have something in place in case it starts to become mildly congested in the future.

  Read the article

• Use shared 404 page for virtual hosts in Nginx

  - by Choy

  I'd like to have a shared 404 page to use across my virtual hosts. The following is my setup. Two sites, each with their own config file in /sites-available/ and /sites-enabled/ www.foo.com bar.foo.com The www directory is set up as: www/ foo.com/ foo.com/index.html bar.foo.com/ bar.foo.com/index.html shared/ shared/404.html Both config files in /sites-available are the same except for the root and server name: root /var/www/bar.foo.com; index index.html index.htm index.php; server_name bar.foo.com; location / { try_files $uri $uri/ /index.php; } error_page 404 /404.html; location = /404.html { root /var/www/shared; } I've tried the above code and also tried setting error_page 404 /var/www/shared/404.html (without the following location block). I've also double checked to make sure my permissions are set to 775 for all folders and files in www. When I try to access a non-existent page, Nginx serves the respective index.php of the virtual host I'm trying to access. Can anyone point out what I'm doing wrong? Thanks!

  Read the article

• Running Windows Update inside Windowx XP Mode

  - by Noam Gal

  I am working on a Win 7 Ultimate machine, and was using XP for some development tasks (for compatibility checks). Everything worked like a charm on the XP, including updates. Two days ago I had to switch computer (mainly a new motherboard/cpu), and I had just stuck my old HD inside the newer case. Win 7 worked like a charm - installed all the new drivers, identified everything automatically, no sweat. The trouble started when I tried running my old XP mode - it won't launch, complaining about the cpu change. I figured it's not a big deal, and I deleted the VM, and re-ran XP mode. It told me it can't find it, and offered to create a new one, just what I wanted. I had finished setting up the new XP mode VM, and it seems to work just fine. Got it to use the host network adapter, so I can surf from "inside". But I can't get Windows Update to run. Whenever I click on the "Custom" button on the WU site, after a short while, I get the [Error number: 0x80072EFD] page. I tried several solution from around the web for it (clearing some cache and restarting the wuauserv, even a microsoft fix-it run), but still nothing seems to work. Anyone here has any new tip for me? Thanks.

  Read the article

• Issue booting Linux Mint from Live CD?

  - by Vee

  I had Windows 8 and Linux Mint 15 dual booted on my laptop. When I first installed Linux, I wasn't able to load into because the grub would not show. To fix this, I used boot-repair from a Live CD. This time, I updated to Windows 8.1 and it showed a watermark telling me my secure boot wasn't configured properly. I then went and enabled secure boot (BIOS) and I believe it was after that that the Grub would not show once again. I tried to boot from a Linux CD again but when I try, it gives me the following errors: error: failure reading sector 0x0 from 'hd1' error: you need to load the kernel first. Press any key to continue... Before, it was giving me an error with sector 0x6d200 or something instead of 0x0. I am completely unsure of what to do. I do not know what other details to give except that this my have happened after I enabled secure boot, and I actually clicked reset to default setting so I am unsure if any other settings were changed in the BIOS menu.

  Read the article

• Process files in a folder that haven't previously been processed

  - by Paul

  I have a series of files in a directory that I need to carry an action out on using a script. Once the action is done, then I want to keep a log that the file has been processed, so that the next time the script is run, it does not attempt to carry out the action again. So lets say I can find all the files that should be processed like this: for i in `find /logfolder -name '20*.log'` ; do process_log $i echo $i >> processedlogsfile done So I have a file containing the logs I have processed, and my goal would be to modify the for loop such that these processed logs are not processed a second time. Doing a manual scan each time seems inefficient, particularly as the processedlogfiles gets bigger: if grep -iq "$i" processdlogfiles ; then continue; fi It would be good if these files could be excluded when setting up the for loop. Note that the OS in question is a linux derivative, a managment appliance, with a limited toolset (no attr command for example) and so no way to install additional utilities (well it is possible but not an option). Most common bash shell commands are available though. Also, the filenames and locations of the processed files must remain where they are - they can't be altered to reflect their processed status

  Read the article

• How can I manage AWS VPC ssh access accounts and keys across multiple instances?

  - by deitch

  I am setting up a standard AWS VPC structure: a public subnet some private subnets, hosts on each, ELB, etc. Operational network access will be via either an ssh bastion host or an openvpn instance. Once on the network (bastion or openvpn), admins use ssh to access the individual instances. From what I can tell all of the docs seem to depend on a single user with sudo rights and a single public ssh key. But is that really best practice? Isn't it much better to have each user access each host under their own name? So I can deploy accounts and ssh public keys to each server, but that rapidly gets unmanageable. How do people recommend managing user accounts? I've looked at: IAM: It doesn't like like IAM has a method for automatically distributing accounts and ssh keys to VPC instances. IAM via LDAP: IAM doesn't have an LDAP API LDAP: set up my own LDAP servers (redundant, of course). Bit of a pain to manage, still better than managing on every host, especially as we grow. Shared ssh key: rely on the VPN/bastion to track user activities. I don't love it, but... What do people recommend? NOTE: I moved this over from accidentally posting in StackOverflow.

  Read the article

• Apache 2.4, Ubuntu 12.04 Forbidden Errors

  - by tubaguy50035

  I just installed Apache 2.4 today, and I'm having some issues getting vhost configuration to work correctly. Below is the vhost conf <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /hosting/Client/site.com/www ServerName site.com ServerAlias www.site.com <Directory "/hosting/Client/site.com/www"> Options +Indexes +FollowSymLinks Order allow,deny Allow from all </Directory> DirectoryIndex index.html </VirtualHost> There is an index.html file in /hosting/Client/site.com/www. When I go to the site, I receive a 403 forbidden error. The www-data group is the group on the www folder, which I've already given all permissions (r/w/x). I'm really at a loss as to why this is happening. Any thoughts? If I remove the vhost and go straight to the IP address, I get the default, "It works!" page. So I know that it's working. The error log says "client denied by server configuration". apache2ctl -S dump: nick@server:~$ apache2ctl -S /usr/sbin/apache2ctl: 87: ulimit: error setting limit (Operation not permitted) VirtualHost configuration: *:80 is a NameVirtualHost default server site.com (/etc/apache2/sites-enabled/site.com.conf:1) port 80 namevhost site.com (/etc/apache2/sites-enabled/site.com.conf:1) alias www.site.com port 80 namevhost site.com (/etc/apache2/sites-enabled/site.com.conf:1) alias www.site.com ServerRoot: "/etc/apache2" Main DocumentRoot: "/var/www" Main ErrorLog: "/var/log/apache2/error.log" Mutex watchdog-callback: using_defaults Mutex default: dir="/var/lock/apache2" mechanism=fcntl Mutex mpm-accept: using_defaults PidFile: "/var/run/apache2.pid" Define: DUMP_VHOSTS Define: DUMP_RUN_CFG Define: ENALBLE_USR_LIB_CGI_BIN User: name="www-data" id=33 not_used Group: name="www-data" id=33 not_used Ouput of namei -mo /hosting/Client/site/www/index.html f: /hosting/Client/site.com/www/index.html drwxr-xr-x root root / drwxr-xr-x root root hosting drwxr-xr-x root root Client drwxr-xr-x nick www-data site.com drwxr-xr-x nick www-data www -rw-rwxr-x nick www-data index.html

  Read the article

• java max heap size, how much is too much

  - by brad

  I'm having issues with a JRuby (rails) app running in tomcat. Occasionally page requests can take up to a minute to return (even though the rails logs processed the request in seconds so it's obviously a tomcat issue). I'm wondering what settings are optimal for the java heap size. I know there's no definitive answer, but I thought maybe someone could comment on my setup. I'm on a small EC2 instance which has 1.7g ram. I have the following JAVA_OPTS: -Xmx1536m -Xms256m -XX:MaxPermSize=256m -XX:+CMSClassUnloadingEnabled My first thought is that Xmx is too high. If I only have 1.7gb and I allocated 1.5gb to java, i feel like I'll get a lot of paging. Typically my java process shows (in top) 1.1g res memory and 2g virtual. I also read somewhere that setting the Xms and Xmx to the same size will help as it eliminates time spend on memory allocation. I'm not a java person but I've been tasked with figuring out this problem and I'm trying to find out where to start. Any tips are greatly appreciated!! update I've started analyzing the garbage collection dumps using -XX:+PrintGCDetails When i notice these occasional long load times, the gc logs go nuts. the last one I did (which took 25s to complete) I had gc log lines such as: 1720.267: [GC 1720.267: [DefNew: 27712K->16K(31104K), 0.0068020 secs] 281792K->254096K(444112K), 0.0069440 secs] 1720.294: [GC 1720.294: [DefNew: 27728K->0K(31104K), 0.0343340 secs] 281808K->254080K(444112K), 0.0344910 secs] about 300 of them on a single request!!! Now, I don't totally understand why it's always GC'ng from ~28m down to 0 over and over.

  Read the article

• Determining a realistic measure of requests per second for a web server

  - by Don

  I'm setting up a nginx stack and optimizing the configuration before going live. Running ab to stress test the machine, I was disappointed to see things topping out at 150 requests per second with a significant number of requests taking 1 second to return. Oddly, the machine itself wasn't even breathing hard. I finally thought to ping the box and saw ping times around 100-125 ms. (The machine, to my surprise, is across the country). So, it seems like network latency is dominating my testing. Running the same tests from a machine on the same network as the server (ping times < 1ms) and I see 5000 requests per second, which is more in-line with what I expected from the machine. But this got me thinking: How do I determine and report a "realistic" measure of requests per second for a web server? You always see claims about performance, but shouldn't network latency be taken into consideration? Sure I can serve 5000 request per second to a machine next to the server, but not to a machine across the country. If I have a lot of slow connections, they will eventually impact my server's performance, right? Or am I thinking about this all wrong? Forgive me if this is network engineering 101 stuff. I'm a developer by trade. Update: Edited for clarity.

  Read the article

• Unable to install mysql-server in Ubuntu

  - by Arihant

  I am unable to install mysql-server on my ubuntu 9.10 server machine. When using apt-get install mysql-server the output is : # apt-get install mysql-server Reading package lists... Done Building dependency tree Reading state information... Done mysql-server is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 120 not upgraded. 2 not fully installed or removed. After this operation, 0B of additional disk space will be used. Setting up mysql-server-5.1 (5.1.37-1ubuntu5.4) ... * Stopping MySQL database server Mysqld [ OK ] * Starting MySQL database server mysqld [fail] invoke-rc.d: initscript mysql, action "start" failed. dpkg: error processing mysql-server-5.1 (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of mysql-server: mysql-server depends on mysql-server-5.1; however: Package mysql-server-5.1 is not configured yet. dpkg: error processing mysql-server (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: mysql-server-5.1 mysql-server E: Sub-process /usr/bin/dpkg returned an error code (1) I cant find a satisfactory solution to this problem anywhere. Many sites tell to reinstall it but its not working. Any help will be appreciated. Thank you..

  Read the article

• Explorer.EXE ordinal 423 not found in urlmon.dll after updates/IE8 install

  - by Zoot

  Setting up a brand new Dell Optiplex 980 with Windows XP SP3, and everything started up fine on the first boot. My first task was to install system updates, including IE8 and WGA. After the required reboot after installing updates, I now get this error message: Explorer.EXE Ordinal not found. The ordinal 423 could not be located in the dynamic link library urlmon.dll Per my cursory Google search, this forum thread places the blame squarely on IE8. The solution provided is to enter safe mode and remove IE8. Unfortunately, when I press F8 to choose to boot safe mode, I only have the option of "Windows XP SP3 Professional" and no safe mode options. Any other ideas? Thanks in advance. FYI, I can get to the Windows Task Manager by holding down Control-Alt-Delete, but programs don't seem to run properly if you select them. I tried chatting with Dell Support, and we tried to initiate the system restore at c:\windows\system32\restore\rstrui.exe, but that had a similar "ordinal 423 not found in urlmon.dll" error.

  Read the article

• Prevent Roaming profiles from syncing certain elements

  - by user29919

  Hello everyone, I'm somewhat new to the Server 2008 front, and I'm afraid I've hit my first snag: I've set up roaming profiles, and they appear to be working too well. Is there a way to limit, ideally on a folder/object basis, what gets synced with a roaming profile? What I'm trying to do is: 1) stop my roaming profile from syncing desktop layout - I run a dual-screen desktop and a laptop, and it's really annoying to have to reposition everything after logging onto the laptop, because it forces everything onto one screen. 2) stop it from syncing registry variables - specifically, I want Visual Studio to load different setting files on each computer. Currently, the variable that contains that path is getting synced whenever I log in, so I get the settings from whatever box I last logged out from. 3) stop syncing the start menu - this one's not as big, but I'm noticing 'program not found' icons even for programs that are installed. they work when I click them - they just look ugly. I'm running Windows SBS 2008 x64 with two Win7 clients (x86 Pro, and X64 Ultimate). Is there a simple way to do that? Or am I trying to work too much against what roaming profiles are designed for? I could, of course, set up different profiles for the desktop and laptop, but that seems to defeat the point of roaming profiles entirely... Thanks in advance! Any help will be much appreciated =)

  Read the article

• Windows 7 network performance tuning for LAN

  - by Hubert Kario

  I want to tune Windows 7 TCP stack for speed in a LAN environment. Bit of background info: I've got a Citrix XenServer set up with Windows 2008R2, Windows 7 and Debian Lenny with Citrix kernel, Windows machines have Tools installed the iperf server process is running on different host, also Debian Lenny. The servers are otherwise idle, tests were repeated few times to confirm results. While testing with iperf 2008R2 can achieve around 600-700Mbps with no tuning what so ever but I can't find any guide or set of parameters that will make Windows 7 achieve anything over 150Mbps with no change in TCP window size using -w parameter to iperf. I tried using netsh autotuining to disabled, experimental, normal and highlyrestricted - no change. Changing congestionprovider doesn't do anything, just as rss and chimney. Setting all the available settings to same values as on Windows 2008R2 host doesn't help. To summarize: Windows 2008R2 default settings: 600-700Mbps Debian, default settings: 600Mbps Windows 7 default settings: 120Mbps Windows 7 default, iperf -w 65536: 400-500Mbps While the missing 400Mbps in performance I blame on crappy Realtek NIC in the XenServer host (I can do ~980Mbps from my laptop to the iperf server) it doesn't explain why Windows 7 can't achieve good performance without manually tuning window size at the application level. So, how to tune Windows 7?

  Read the article

• JBoss 5 on AIX 5.3

  - by jess

  I am a very newbie for AIX and system monitoring. Actually our application currently run production on jboss 5.1 in AIX 5.3. Please check below configuration & system settings. AIX system configuration OS Level 5.3.9.0 (oslevel -g) Physical Memory size 24GB (svmon -G) Page space 4GB (lsps -s) processors 3 cores, Processor Type: PowerPC_POWER6, Processor Clock Speed: 4704 MHz (prtconf | grep Processor) Java version JRE 1.6.0 IBM AIX build pap6460sr10fp1-20120321_01 (SR10 FP1) (java -fullversion) JBoss configuration JBoss 5.1/JBoss ESB 4.11 Hornetq messaging with consumer flow control java opts : -d64 -Xms2g -Xmx4g -XX:MaxPermSize=1024m Sometime we observe very strange behavior in the JBoss that freeze without any error logs. Also server log stop without any further trace. We also not able to get thread dump (kill -3) and its not generate at that point. (kill -3 xxxxx works in normal circumstances) Only option available for us was restart the jboss server and its seem all messages that were in queues during the freeze time process after restarting. We try tweak some of setting in JBoss hornetq, we though issue was there. Hornetq Stuck By Default. But we haven't any luck and also unable to isolate the issue in any point. We looking at tool like nmon for monitoring this but no clue is that good enough to do so. Please provide some point to investigate this issue. Thanks

  Read the article

• Rundeck get verbose output of command executing on node

  - by Leon Stafford

  I have Rundeck executing a remote script, which is in python is using print statements to return output normally such as: $ python mytest.py PASS: Condition 1 passed PASS: Condition 2 passed PASS: and so on... When I run this via Rundeck, however, it doesn't show me the same print generated outputs as above. In Rundeck's most detailed Debug output mode, I only receive the following: 06:31:12 Permanently added 'myremotenode.com' (RSA) to the list of known hosts. 06:31:12 SSH_MSG_NEWKEYS sent 06:31:12 SSH_MSG_NEWKEYS received 06:31:12 SSH_MSG_SERVICE_REQUEST sent 06:31:13 SSH_MSG_SERVICE_ACCEPT received 06:31:13 Authentications that can continue: publickey,password,keyboard-interactive 06:31:13 Next authentication method: publickey 06:31:13 Authentication succeeded (publickey). 06:31:13 /cygdrive/c/Program Files (x86)/Mozil... 06:32:06 Adding reference: ant.PropertyHelper 06:32:06 Setting project property: sshexec.output -> /cygdrive/c/Prog... I know that the remote script is actually executing just as usual, as I'm receiving other emails generated by the ~30min long script. Obviously, I don't want to have to wait 30mins to see the result of each print statement within the python script. How can I get the same level of output in Rundeck as I do in the bash shell directly?

  Read the article

• Backup strategy for developer-focused Apple environments?

  - by ewwhite

  It's interesting to see the technological split between structured corporate environments and more developer-driven/startup environments. Some of the Microsoft technologies I take for granted (VSS, Folder Redirection, etc.) simply are not available when managing the increasing number of Apple laptops I see in DevOps shops. I'm interested in centralized and automated backup strategies for a group of 30-40 Apple laptops... How is this typically done safely and securely, assuming these are company-owned machines (versus BYOD)? While Apple has Time Machine, it's geared toward individual computer backups and doesn't seem to work reliably in a group setting. Another issue with these workstations is the presence of Vagrant/Virtual Box VMs on the developers' systems. Time Machine and virtual machines typically don't work well unless the VMs are excluded from the backup set. I'd like a push-based backup process with some flexible scheduling options. I know how to handle the backend storage, but I'm not sure on what needs to be presented to the client systems. Due to the nature of the data here, cloud-based backup may not be a viable option. Any suggestions about how you handle this in your environment would be appreciated. Edit: The virtual machine backups are no longer important. They can be excluded from the process and planning.

  Read the article

< Previous Page | 428 429 430 431 432 433 434 435 436 437 438 439  | Next Page >