Search Results

Search found 27336 results on 1094 pages for 'network state'.

Page 433/1094 | < Previous Page | 429 430 431 432 433 434 435 436 437 438 439 440  | Next Page >

• How can I use my laptop's monitor as my PC's ONLY monitor? [closed]

  - by Randell

  Possible Duplicate: Can I use my laptop as a second monitor for my desk computer? My PC's monitor just died and I'm not looking at buying a new monitor anytime soon. So I'm thinking of using my laptop's monitor for it. Both machines are running on Fedora linux. Edit: Both machines are connected to the same wireless network. PC needs to log in before it can connect to the network if I'm not mistaken. Update: This is different from Can I use my laptop as a second monitor for my desk computer? , because that question is asking how to use the laptop screen as the secondary display, not as the only display.

  Read the article

• b43 module loaded, but no interface showed up

  - by Eduardo Bezerra

  I'm using CentOS 6.3 x86_64 on a hardware with a BCM43224 chip for wi-fi. I installed the b43-fwcutter module and then run modprobe b43, with no error messages. However, no new network interface showed up, and the return of iwconfig is: lo no wireless extensions. eth0 no wireless extensions. lspci -nn | grep 43224 returns: 03:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01) and uname -a: Linux localhost.localdomain 2.6.32-279.14.1.el6.x86_64 #1 SMP Tue Nov 6 23:43:09 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux Any ideas of how to make the wireless device work?

  Read the article

• Ubuntu Software Center Missing and cannot install?

  - by luqman

  My ubuntu was remove ubuntu software center because i want to reinstall again.but i used terminal...i cannot to install ubuntu software center.. :~$ sudo apt-get install software-center Reading package lists... Done Building dependency tree Reading state information... Done Package software-center is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source Why?

  Read the article

• Can a switch consume bandwidth?

  - by aashiq

  I have a network with a router and a switch. At first my ISP's optical fiber is connected with media converter input port. Than Ethernet cable (output port of Media converter) is connected with the switch. Then an output Ethernet cable is connected with our inner Microtik router. Then this router is connected with another LAN switch. From this switch we have got every connection other switch. It is our total network structure. Our bandwidth is 2 Mbps. From the 11th of March our MRTG graph shows high all the time even when my all switch is switched off except LAN switch. That's why our line is breaking up (Voice call). How could be it possible? My all PC's bandwidth is limited but when connected PC with media converter directly then the graph shows normal. That's why I can't blame my ISP.

  Read the article

• How can I connect to my Airport Extreme Shared Disk using Windows?

  - by matt ryan

  I have a shared disk attached to my Airport Extreme, which I can connect to remotely in OS X through the finder via command - k, and entering in the proper address: afp://test.dyndns.org:1111 1111 being the port I've reserved for the disk in the AE port mapping. This is such a great feature, but I don't always have access to a Mac. My question is how can I connect to this drive via Windows XP? Please note, that the shared drive is a Drobo FS and formatted to handle both Windows and Mac OS. I've tried mapping a network drive via My Computer - Tools - Map Network Drive and entering: \\test.dyndns.org:1111\Drobo-Name I've also tried Start - Run and entering the same, both with and without the port #.

  Read the article

• NAT and ISP Subnet when load balancing on pfsense?

  - by dannymcc

  I have a pfsense box that I'm trying to plan the configuration for. I am going to be load balancing two ISP's, each with their own /29 static IP subnet. The question I have is in relation to the way those IP's are associated with workstations on the local network. Currently I have some workstations with local (192.168.1.0/29) IP addresses, and other more complicated workstation setups have their own public IP address. Some of the more complicated systems have a NAT 1:1 configuration where I forward a public IP address to a local IP address. Others however are directly on the ISP subnet and cannot be seen on our local network. Is this configuration possible with pfsense? If so, what terms should I be looking through the documentation for? Here is a simple/brief diagram of what I am trying to achieve.

  Read the article

• NT4 server generate too much weird DNS queries, How can i see the source PID?

  - by Hanan N.

  I have a NT4 server that in the last two weeks started to generate too many weird DNS queries to the DNS server is set to use. I have got warnings from the IPS system that it has blocked the responses from the DNS server back to the NT4 server. The queries it generate doesn't relate to any computer in the network, it is like 120624100088.xxxxxxx.net where xxx is the internal network, the numbers are just random at each query. I have done some research on how to get the PID that is generating the queries, and i found that only Process Monitor could give me that information, but since it is NT4 system Process Monitor doesn't work on it. It is a production server and i am just can't stop services as i want. I would like to get your advice on how can i get the PID that is generating these queries? Thanks.

  Read the article

• OpenVPN Configuration - Windows 7 client & debian server

  - by Guillaume

  I recently formatted my Windows 7 computer and lost my client's config files for OpenVPN. I recovered the certificates and default config that were left on the server but I haven't managed to make the whole thing work again. I assume the server's config and routing table are OK because it was working before (although quite some time ago). Would any of you experts be able to help? server.conf # Serveur TCP/666 mode server proto udp port 666 dev tun # Cles et certificats ca ca.crt cert server.crt key server.key dh dh1024.pem tls-auth ta.key 0 cipher AES-256-CBC # Reseau server 10.8.0.0 255.255.255.0 #push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 208.67.222.222" push "dhcp-option DNS 208.67.220.220" push "redirect-gateway def1" keepalive 10 120 # Securite user nobody group nogroup chroot /etc/openvpn/jail persist-key persist-tun comp-lzo # Log verb 3 mute 20 status openvpn-status.log log-append /var/log/openvpn.log client.conf # Client client dev tun proto udp remote *my server's ip address*:666 cipher AES-256-CBC # Cles ca ca.crt cert client1.crt key client1.key tls-auth ta.key 1 # Securite nobind persist-key persist-tun comp-lzo verb 3 Routing table on debian server when OpenVPN server is running: Destination Gateway Genmask Indic Metric Ref Use Iface 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 my server's ip * 255.255.255.0 U 0 0 0 eth0 default 72815.trg.dedic 0.0.0.0 UG 0 0 0 eth0 Routing table on Windows 7 client (OpenVPN not working) =========================================================================== Interface List 19...00 f0 8a 1b 6e 5c ......TAP-Win32 Adapter V9 12...90 2e 34 33 84 7b ......Atheros AR8151 PCI-E Gigabit Ethernet Controller ( NDIS 6.20) 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.11 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.11 276 192.168.1.11 255.255.255.255 On-link 192.168.1.11 276 192.168.1.255 255.255.255.255 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.11 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.11 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: [...] =========================================================================== Persistent Routes: None And when the link is established between my client and the server: The server's routing table stays the same. The client's becomes: =========================================================================== Interface List 19...00 f0 8a 1b 6e 5c ......TAP-Win32 Adapter V9 12...90 2e 34 33 84 7b ......Atheros AR8151 PCI-E Gigabit Ethernet Controller ( NDIS 6.20) 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.11 20 0.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 10.8.0.1 255.255.255.255 10.8.0.5 10.8.0.6 30 10.8.0.4 255.255.255.252 On-link 10.8.0.6 286 10.8.0.6 255.255.255.255 On-link 10.8.0.6 286 10.8.0.7 255.255.255.255 On-link 10.8.0.6 286 my server's ip 255.255.255.255 192.168.1.1 192.168.1.11 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 192.168.1.0 255.255.255.0 On-link 192.168.1.11 276 192.168.1.11 255.255.255.255 On-link 192.168.1.11 276 192.168.1.255 255.255.255.255 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 10.8.0.6 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.11 276 255.255.255.255 255.255.255.255 On-link 10.8.0.6 286 =========================================================================== Persistent Routes: None What's working: Server and client do connect to each other, SSL certificates are OK. The client gets an IP (10.8.0.6) from the server OpenVPN client is started as an administrator. But: I cannot ping the other one on either side. 'Gateway' value is empty on client's side (in the adapter's "status" window). Client has got no internet access when the link is up. Ideal configuration: I only want the client to be able to use the server's Internet access and access its resources (MySQL server in particular). I do not need or want the server to access the client's local network. The client needs to be able to access it's local network, although all Internet traffic should be redirected to the VPN link. I spent a considerable amount of time on this but it's still not working, any help would be much appreciated. Thanks :)

  Read the article

• Is there no such thing as a Gigabit switch?

  - by Torben Gundtofte-Bruun

  According to the manufacturer specification, even my rather plain desktop computer has "Gigabit Ethernet". So when I want to copy large files over the LAN (not Internet) it would make sense to have a gigabit switch. I'm searching eBay for a gigabit switch for a planned home network upgrade. The products I find are all labeled "gigabit" but they all have 24 x 10/100Mbit autosensing ports and sometimes 2 x 10/100/1000Mbit autosensing ports. It was my understanding that 10/100 is ancient and that modern computers have network interfaces that work with 1000Mbit, so it would make sense to get a switch that has 24 x 1000Mbit ports. Did I misunderstand, or are sellers (deliberately?) mislabeling older hardware? (Let's not dive into wired vs. wireless networks and how "N" wireless is fast. You'd be right, but not answering the question.)

  Read the article

• SQL2008 Won't Work After SP1 Install?

  - by leen3o

  I have SQL2008 installed on my Win2008 server, and its been working fine - I have sites running using SQL databases etc.. I thought I would install SQL2008 SP1, but after install I cannot connect to SQL via Management Studio, and in configuration manager I cannot start SQL? TITLE: Connect to Server Cannot connect to #MYINSTANCENAME#. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=-1&LinkId=20476 BUTTONS: OK I'm not really a techie so a bit stuck?? any ideas??

  Read the article

• Wireless drops on HP ENVY dv6 with RT3290 wireless, worked without problem prior to upgrading to Ubuntu 13.10, can it be fixed?

  - by Tim

  I have a HP ENVY dv6 Notebook PC with an AMD A10 quad core and RT3290 wireless. Since I upgraded from Ubuntu 13.04 to 13.10, the wireless connects, but then drops after a few minutes or longer, whether or not I am running openconnect to get through a VPN. If I attempt to run a remote X client (e.g. remote xterm) it drops. If I don't run an X client, it disconnects after a while, requiring a reload of the driver and reconnect. Wireless info... sudo lshw -c network *-network description: Wireless interface product: RT3290 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 68:94:23:a7:09:cb width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.11.0-12-generic firmware=0.37 ip=192.168.1.115 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:55 memory:f0210000-f021ffff I have successfully built and installed the MediaTek driver with no luck on connecting, then the system hangs on reboot and I have to recover/undo the changes to boot successfully.

  Read the article

• Connected to internet but can't browse after trying to remove Covenant Eyes

  - by Joanna

  I recently got a MacBook Pro. It connects to ethernet\wifi and has internet but when I open Safari or Firefox, nothing happens. I get a timeout for all websites. I had Covenant Eyes on my Mac before and tried to remove it. My friends who work with computers have tried everything (ping, nslookup etc). Network diagnostics show no problems I can see I'm connected through ifconfig because I get an IP. I also get a response pinging www.google.gr. There are no proxies set in my Network preferences. Any ideas?

  Read the article

• RDP failing due to Audit Failure on the IPSec driver

  - by paulwhit

  I am trying to RDP into a Windows 7 Hyper-V image connected to a corporate network that publishes IPSec policies via Active Directory. I am seeing this error in the log: IPsec dropped an inbound clear text packet that should have been secured. If the remote computer is configured with a Request Outbound IPsec policy, this might be benign and expected. This can also be caused by the remote computer changing its IPsec policy without informing this computer. This could also be a spoofing attack attempt. Remote Network Address: XXX.XXX.XXX.XXX Inbound SA SPI: 0 How do I change my settings on the computer using RDP to something suitable for the domain-joined Hyper-V image?

  Read the article

• Airport Express chokes Wi-Fi for a few seconds, several times per hour. Any idea why?

  - by user13727

  I'm using a MacBookPro connected to an AiportExpress' Wi-FI network. Every once in a while, the Wi-Fi will choke up and either drop some packets, or lag horribly for several seconds. I'm losing hair over this because every time I chat on Skype, the call hangs randomly due to this problem. Any idea what's wrong? Some more details: two networks are set up: 2.4Ghz and 5Ghz, and the issue happens on both the network uses WPA2 Personal for security the Airport is in the same room with my computer the Airport is fairly new, bought this summer, model number off the back: A1392 tried connecting to a neighbours wifi to see if it's a problem with my computer, or interference. It's not, it doesn't happen on their network. tried resetting it several times tried changing channels manually Ping results are below, so you can see what I'm talking about. EDIT: 10.0.1.1 is the Airport's IP 64 bytes from 10.0.1.1: icmp_seq=1795 ttl=255 time=0.813 ms 64 bytes from 10.0.1.1: icmp_seq=1796 ttl=255 time=3.335 ms 64 bytes from 10.0.1.1: icmp_seq=1797 ttl=255 time=3.403 ms 64 bytes from 10.0.1.1: icmp_seq=1798 ttl=255 time=3.414 ms 64 bytes from 10.0.1.1: icmp_seq=1799 ttl=255 time=3.227 ms 64 bytes from 10.0.1.1: icmp_seq=1800 ttl=255 time=3.274 ms 64 bytes from 10.0.1.1: icmp_seq=1801 ttl=255 time=3.253 ms 64 bytes from 10.0.1.1: icmp_seq=1802 ttl=255 time=3.292 ms >>>> choke starts <<< 64 bytes from 10.0.1.1: icmp_seq=1803 ttl=255 time=53.977 ms 64 bytes from 10.0.1.1: icmp_seq=1804 ttl=255 time=35.049 ms 64 bytes from 10.0.1.1: icmp_seq=1805 ttl=255 time=19.820 ms >>>> choke ends <<< 64 bytes from 10.0.1.1: icmp_seq=1806 ttl=255 time=0.716 ms 64 bytes from 10.0.1.1: icmp_seq=1807 ttl=255 time=0.705 ms 64 bytes from 10.0.1.1: icmp_seq=1808 ttl=255 time=0.919 ms 64 bytes from 10.0.1.1: icmp_seq=1809 ttl=255 time=0.659 ms 64 bytes from 10.0.1.1: icmp_seq=1810 ttl=255 time=0.877 ms 64 bytes from 10.0.1.1: icmp_seq=1811 ttl=255 time=0.679 ms 64 bytes from 10.0.1.1: icmp_seq=1812 ttl=255 time=0.854 ms 64 bytes from 10.0.1.1: icmp_seq=1813 ttl=255 time=0.644 ms 64 bytes from 10.0.1.1: icmp_seq=1814 ttl=255 time=3.779 ms ... time passes .. 64 bytes from 10.0.1.1: icmp_seq=1599 ttl=255 time=0.674 ms 64 bytes from 10.0.1.1: icmp_seq=1600 ttl=255 time=0.930 ms 64 bytes from 10.0.1.1: icmp_seq=1601 ttl=255 time=0.665 ms 64 bytes from 10.0.1.1: icmp_seq=1602 ttl=255 time=1.085 ms Request timeout for icmp_seq 1603 Request timeout for icmp_seq 1604 64 bytes from 10.0.1.1: icmp_seq=1605 ttl=255 time=104.969 ms 64 bytes from 10.0.1.1: icmp_seq=1606 ttl=255 time=11.521 ms 64 bytes from 10.0.1.1: icmp_seq=1607 ttl=255 time=0.926 ms 64 bytes from 10.0.1.1: icmp_seq=1608 ttl=255 time=0.993 ms 64 bytes from 10.0.1.1: icmp_seq=1609 ttl=255 time=0.745 ms And the Signal-Noise ratio:

  Read the article

• Pretty URL in ADF Faces of JDeveloper 11.1.2.2

  - by Frank Nimphius

  Many features planned for Oracle JDeveloper 12c find their way into current releases of Oracle JDeveloper 11g R1 and JDeveloper 11g R2. One example of such a feature is "pretty URL" - or "clean URL" as the Oracle JDeveloper 11g R2 (11.1.2.2) documentation puts it. "A.2.3.24 Clean URLs Historically, ADF Faces has used URL parameters to hold information, such as window IDs and state. However, URL parameters can prevent search engines from recognizing when URLs are actually the same, and therefore interfere with analytics. URL parameters can also interfere with bookmarking. By default, ADF Faces removes URL parameters using the HTML5 History Management API. If that API is unavailable, then session cookies are used.You can also manually configure how URL parameters are removed using the context parameter oracle.adf.view.rich.prettyURL.OPTIONS. Set the parameter to off so that no parameters are removed. Set the parameter to useHistoryApi to only use the HTML5 History Management API. If a browser does not support this API, then no parameters will be removed. Set the parameter to useCookies to use session cookies to remove parameters. If the browser does not support cookies, then no parameters will be removed." See: http://docs.oracle.com/cd/E26098_01/web.1112/e16181/ap_config.htm#ADFUI12856 So basically, what this part in the documentation says is: In JDeveloper 11g R2 (11.1.2.2), Oracle ADF Faces automatically removes its internally used dynamic parameters from the URL You can influence the setting with the prettyURL.OPTIONS context option, which however is not recommended you to do because the default behavior is able to detect if the browser client supports HTML 5 History management or not. In the latter case it the uses a session cookie and if this doesn't work, falls back to the "old" URL parameter adding. The information that is not so explicit and clearly mentioned in the documentation is that this is only for ADF Faces parameters (such as _afrLoop, Adf-Window-Id, etc.), but not the ADF controller token (_adf.ctrl-state)! Removing the ADF controller token is an enhancement request that will be implemented in Oracle JDeveloper 12c

  Read the article

• Allow users to view Word documents only and not be able to edit, copy or save them.

  - by Alexander

  Hello In a traditional Windows Server 2003 environment with AD, we have shared a folder for our policy documents (MS Word). These documents get edited/updated now and then by the administrator(principal of college). Users only have read-only access to the folder, but they can still save-as and then change the content. Sharepoint is a possible solution but not easy to implement. We also thought of using a CMS on Linux and installing Joomla to let users only view the docs with a document management system... but is it possible to automatically retrieve the policy folder on the network and convert or put it in a format that users can only view and not copy? We also thought of saving the docs to secure pdf format but the principal wants an automated system. Basically she just wants to work in Word and the policies must be available to staff members on the network. Any ideas? Much appreciated.

  Read the article

• Remote Access to Owncloud Server

  - by John

  I'm currently trying to setup my own own-cloud server, and I've got it fully installed, configured, and accessible from within my own local network. I cannot figure out how to access it from the outside. So far I've: Successfully setup port-forwarding on my local router. I've done so via 'single port forwarding' and 'port range forwarding' Ports 80, 443, 3306 (Apache-Full and MySQL) Successfully obtained my external IP address. I've also tested this magic number from within the network at #insertIPhere/owncloud and it did work. Successfully setup the server using SQLite Successfully setup the server using MySQL Created the following exceptions in my firewall: Allow In Port 80 (Apache Full) Allow In Port 443 (Apache Full) Allow In Port 3306 (MySQL) Tried connecting from several different remote networks, as to troubleshoot something on their end As far as trying to access it, I'm doing so through Google-Chrome and Mozilla Firefox trying to reach the server through #insertIPhere/owncloud using the above public IP address. So what have I missed, and how do I access my server from outside? Thanks in advance for your help and time, and I apologize in advance for what will probably result in my noobish mistake in networking. I've looked at the official documentation. And also this question here.

  Read the article

• 7 Ways To Free Up Hard Disk Space On Windows

  - by Chris Hoffman

  Hard drives are getting larger and larger, but somehow they always seem to fill up. This is even more true if you’re using a solid-state drive (SSD), which offers much less hard drive space than traditional mechanical hard drives. If you’re hurting for hard drive space, these tricks should help you free up space for important files and programs by removing the unimportant junk cluttering up your hard disk. Image Credit: Jason Bache on Flickr 7 Ways To Free Up Hard Disk Space On Windows HTG Explains: How System Restore Works in Windows HTG Explains: How Antivirus Software Works

  Read the article

• Where are Wireless Profiles stored in Ubuntu

  - by LonnieBest

  Where does Ubuntu store profiles that allow it to remember the credentials to private wireless networks that it has previously authenticate to and used? I just replaced my Uncle's hard drive with a new one and installed Ubuntu 10.04 on it (he had Ubuntu 9.10 on his old hard drive. He is at my house right now, and I want him to be able to access his private wireless network when he gets home. Usually, when I upgrade Ubuntu, I have his /home directory on another partition, so his wireless profile to his own network persists. However, right now, I'm trying to figure out which .folder I need to copy from his /home/user folder on the old hard drive, to the new hard drive, so that he will be able to have wireless Internet when he gets home. Does anyone know with certainty, exactly which folder I need to copy to the new hard drive to achieve this?

  Read the article

• See you at OSCON!

  - by darcy

  In just under a month, I'll be speaking at the OSCON Java conference about various OpenJDK and JDK 7 matters: JDK 7 in a Nutshell The State of JDK and OpenJDK More detailed talks on those topics include Stuart's session on Coin in Action: Using New Java SE 7 Language Features in Real Code and Dalibor's OpenJDK – When And How To Contribute To The Java SE Reference Implementation. See you in Portland!

  Read the article

• ASA and cisco vs NSA sonic firewall

  - by Lbaker101

  Currently I’m trying to structure our network to fully support and be redundant with BGP/Multi homing. Our current company size is 40 employees but the major part of that is our Development department. We are a software company and continued connection to the internet is a requirement as 90% of work stops when the net goes down. The only thing hosted on site (that needs to remain up) is our exchange server. Right now i'm faced with 2 different directions and was wondering if I could get your opinions on this. We will have 2 ISPs that are both 20meg up/down and dedicated fiber (so 40megs combined). This is handed off as an Ethernet cable into our server room. ISP#1 first digital ISP#2 CenturyLink we currently have 2x ASA5505s but the 2nd one is not in use. It was there to be a failover and it just needs the security+ license to be matched with the primary device. But this depends on the network structure. I have been looking into the hardware that would be required to be fully redundant and I found that we will either of the following. 2x Cisco 2921+ series routers with failover licenses. They will go in front of the ASAs and either connects in a failover state or 1 ISP into each of the 2921 series routers and then 1 line into each of the ASAs (thus all 4 hardware components will be used actively). So 2x Cisco 2921+ series routers 2x Cisco ASA5505 firewalls The other route 2x SonicWalls NSA2400MX series. 1 primary and the secondary will be in a failover state. This will remove the ASAs from the network and be about 2k cheaper than the cisco route. This also brings down the points of failure because it’s just the 2x sonicwalls It will also allow us to scale all the way up to 200-400 users (depending on their configuration). This also makes so the Sonic walls. So the real question is with the added functionality ect of the sonicwall is there a point in paying so much more to stay the cisco route? Thanks!

  Read the article

• SOA &amp; Application Grid Specialization&ndash; Education Implementation Assessment - Step 4 of 6

  - by Jürgen Kress

    In our first step to become SOA Specialized & Application Grid Specialized we highlighted the OMM system to register your opportunities. In our second step we featured marketing activities to create your reference cases and run joint marketing campaigns. In the third step we focused on the competence center assessments SOA Sales assessment & SOA Pre-Sales assessment & Support assessment / Application Grid Sales assessment & Application Grid Pre-Sales assessment & Support assessment In the forth step we will focus on the education implementation assessment criteria: · Oracle Application Grid Certified Implementation Specialist · Oracle Service-Oriented Architecture Certified Implementation Specialist Bootcamp training steps (optional): Login to Oracle Partner Network (support for login contact Partner Business Centers) Attend a SOA or Application Grid bootcamp to learn the product hands-on Find a training close to your location in the local training calendar Pearsonvue Steps: Go to http://www.pearsonvue.com/Oracle/ ·Create a web account. (will take up to 24 hours) if you need your OPN Company ID (please contact Partner Business Centers) ·Register and attend the Oracle Service-Oriented Architecture Certified Implementation Specialist (1Z1-451) or Oracle Application Grid Certified Implementation Specialist  (1Z1-523) at a training center close to you. The Application Grid Specialized is in beta phase, therefore we give away free vouchers; please contact Jürgen Kress if you like to get one. ·Submit your successful exam If you need to get an Oracle Partner Network Account please contact our Partner Business Centers. For more information on Specialization please visit our OPN Specialized Webcast Series and become a member in our SOA Partner Community for registration please visit www.oracle.com/goto/ema/soa Jürgen Kress, SOA Partner Adoption EMEA Thanks for your efforts to become Specialized! Technorati Tags: soa specialization

  Read the article

• wireshark not seeing all packets on WiFi

  - by Caffeine Coma

  I'm using Wireshark on OSX, trying to sniff my home network over WiFi. While I can see packets that are sent to/from the host I'm sniffing on, I'm not seeing anything else that goes over the WiFi. It's like I'm not in promiscuous mode or something (the promiscuous mode box is in fact checked). The router is an Apple Airport Extreme, protected by WPA2. I'm attached to the network I'm trying to sniff, so I'm confused about why I can't see other traffic. Edit: I solved this by the following: Plug Macbook directly into the Airport Extreme router Enable "internet sharing" on Macbook, with no password. Bind wireless device (the one I wanted to sniff) to the WiFi hotspot generated by Internet sharing in step 2. Run Wireshark on the Macbook, bound to device en1. Don't forget to disable sharing after you're done. :-)

  Read the article

• Java Road Trip: Code to Coast (#javaroadtrip)

  - by Justin Kestelyn

  Hey, have you heard? The Java Road Trip bus may be stopping at a city near you this summer, starting June 14. And your peeps at Oracle Technology Network have donated some goodies. What is the Java Road Trip? Basically, we have packed a rock-star bus with demos (Java FX, Oracle ADF, Java EE 6, JDK 7, GlassFish, Java ME) and are putting it on the road; it will make 20 stops across the U.S. in the next couple of months (and MAY may make a special appearance at JavaOne, if we can find a big enough parking space). In many cases these stops will coincide with Java or Oracle user group meet-ups and will always involve beer, food, and free stuff. Furthermore, engineers from HQ will be flying out at various times to rendezvous with these meet-ups and answer your questions. Also, because this tour will only reach a relatively small number of people, we're working hard to provide a virtual experience: there will be a blogger/videographer/photog/tweeter on board, reporting on its every move. You'll find all this content at java.com/roadtrip, and you can get real-time updates via @java. And this new update: If you're attending ODTUG Kaleidoscope in Washington, D.C., in late June, you'll get a chance to see the Java Bus in all its glory. And don't forget your t-shirt, cup, and screen cleaner, all provided by Oracle Technology Network.

  Read the article

• There's IP but can't reach gateway

  - by icky

  I have just installed ubuntu 12.04 on my new laptop, and brought it back to home, but I found the wireless network does not work. Strangely, it has the correct ip, but can't connect to the gateway. ifconfig gives ip 192.168.64.36, with broadcast 192.168.79.255 and mask 255.255.240.0, this are all correct, the gateway is at 192.168.64.1 cat /etc/resolv.conf nameserver 192.168.64.1 nameserver 127.0.0.1 which i think it's also right. but when I ping 192.168.64.1, all packages are lost. Please help me with this, I really do not know what happened to my network settings. Huckle, Thank you for your reply ifconfig wlan0 Link encap:Ethernet Hwaddr 88:f9:af:2a:ca:1b inet addr:192.168.64.36 Bcast:192.168.79.255 Mask:255.255.240.0 inet6 addr: fe80::8a9f:faff:fea2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:376 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3950 TX byetes:60288 iwconfig wlan0 IEEE 802.11bgn ESSID:"Chiono" Mode:Managed Frequency:2.417 GHz Access Point: 82:54:99:94:6D:43 Bit Rate=13.5 Mb/s Tx-Power=13 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=70/70 Signal Level=-32 dBm Rx invalid nwid:0 Rx invalid crypt:0 RX invalid frag:0 Tx excessive retries: 9 Invalid misc:10 Missed beacon:0 route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.64.1 0.0.0.0 UG 0 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.64.0 * 255.255.240.0 U 2 0 0 0 wlan0 Thank you very much

  Read the article

< Previous Page | 429 430 431 432 433 434 435 436 437 438 439 440  | Next Page >