Search Results

Search found 11961 results on 479 pages for 'boot arguments'.

Page 440/479 | < Previous Page | 436 437 438 439 440 441 442 443 444 445 446 447  | Next Page >

• Migrating from one linux install to another: How to keep the second disk around?

  - by Jim Miller

  I've got a linux box running Fedora 19 that I want to move to CentOS 6.4. Rather than trying to do something fancy with the current disk (which has also accumulated a lot of sludge over the years), I'm going to get a new disk, put CentOS on that, and then move the to-be-preserved bits of stuff from the old disk to the new one. I haven't done this yet, but I presume it should be semi-straightforward -- do the CentOS install on the new disk, mount the old disk on /olddisk or somesuch, and start copying. However, I'm not sure how to handle getting the machine to recognize the new empty disk as the target of the CentOS install (I suppose I can just pull the old disk during the installation), remember that this is the intended boot disk once the install has happened), and tweak /etc/fstab (right?) to set up the old disk on the desired mount point. (Both disks are, or will be, SATA.) I could probably hack it together without losing too much hair or doing too much damage, but could anyone offer some advice that would get/keep me on the right track? Thanks!

  Read the article

• "could not find suitable fingerprints matched to available hardware" error

  - by Alex

  I have a thinkpad t61 with a UPEK fingerprint reader. I'm running ubuntu 9.10, with fprint installed. Everything works fine (I am able to swipe my fingerprint to authenticate any permission dialogues or "sudo" prompts successfully) except for actually logging onto my laptop when I boot up or end my session. I receive an error below the gnome login that says "Could not locate any suitable fingerprints matched to available hardware." What is causing this? here are the contents of /etc/pam.d/common-auth file # # /etc/pam.d/common-auth - authentication settings common to all services # # This file is included from other service-specific PAM config files, # and should contain a list of the authentication modules that define # the central authentication scheme for use on the system # (e.g., /etc/shadow, LDAP, Kerberos, etc.). The default is to use the # traditional Unix authentication mechanisms. # # As of pam 1.0.1-6, this file is managed by pam-auth-update by default. # To take advantage of this, it is recommended that you configure any # local modules either before or after the default block, and use # pam-auth-update to manage selection of other modules. See # pam-auth-update(8) for details. # here are the per-package modules (the "Primary" block) auth sufficient pam_fprint.so auth [success=1 default=ignore] pam_unix.so nullok_secure # here's the fallback if no module succeeds auth requisite pam_deny.so # prime the stack with a positive return value if there isn't one already; # this avoids us returning an error just because nothing sets a success code # since the modules above will each just jump around auth required pam_permit.so # and here are more per-package modules (the "Additional" block) auth optional pam_ecryptfs.so unwrap # end of pam-auth-update config #auth sufficient pam_fprint.so #auth required pam_unix.so nullok_secure

  Read the article

• What user information is exposed via a browser?

  - by ipso

  Is there a function or website that can collect and display ALL of the user information that can be obtained via a browser? Background: This of course does not account for the significant cross-reference abilities of large corporations to collate multiple sources and signals from users across various properties, but it's a first step. Ghostery is just a great idea; to show people all of the surreptitious scripts that run on any given website. But what information is available – what is the total set of values stored – that those scripts can collect from? If you login to a search engine and stay logged in but leave their tab, is that company still collecting your webpage viewing and activity from other tabs? Can past or future inputs to pages be captured – say comments on another website? What types of activities are stored as variables in the browser app that can be collected? This is surely a highly complex question, given to countless user scenarios – but my whole point is to be able to cut through all that – and just show the total set of data available at any given point in time. Then you can A/B test and see what is available with in a fresh session with one tab open vs. the same webpage but with 12 tabs open, and a full day of history to boot. (Latest Firefox & Chrome – on Win7, Win8 or Mint13 – although I'd like to think that won't make too much of a difference. Make assumptions. Simple is better.)

  Read the article

• K8NDRE motherboard in server fails to complete BIOS load with error 0078

  - by John

  K8NDRE motherboard with 4 sata drives, was running fine. Drives had raid-0 and raid-1 partitions, using mdadm. The onboard raid is disabled. Upon reformatting the drives, setting a new partition structure and new raid partitions, the bios fails to finish loading, with 0078 in the bottom right corner. Tried using completely new set of drives, and bios worked fine. Able to boot from a usb, format the drives, partition them, start raid, and then installed os. Reboot and received the same error from the bios, 0078. Works fine if I unplug the sata drives. Any thoughts? Physical inspection reveals no damage cables, connectors, or capacitors. Server was running happily for over a year, and this is the first problem it has had. Per Michael Hampton's answer: The drives, unjumpered and supporting sata III worked fine originally, and worked fine for formatting and having new partitions and raid installed on them. I did try jumpering one, with no change. If I put a brand new unformatted drive in, the motherboard recognizes it and I can proceed with formatting and installing. When I reboot, I get the 0078. I have 4 sata cables-the board supports 4 drives, so I tried each and no change. I am close to calling the motherboard done.

  Read the article

• how can i move ext3 partition to the beginning of drive without losing data?

  - by Felipe Alvarez

  I have a 500GB external drive. It had two partitions, each around 250GB. I removed the first partition. I'd like to move the 2nd to the left, so it consumes 100% of the drive. How can this be accomplished without any GUI tools (CLI only)? fdisk Disk /dev/sdd: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc80b1f3d Device Boot Start End Blocks Id System /dev/sdd2 29374 60801 252445410 83 Linux parted Model: ST350032 0AS (scsi) Disk /dev/sdd: 500GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 2 242GB 500GB 259GB primary ext3 type=83 dumpe2fs Filesystem volume name: extstar Last mounted on: <not available> Filesystem UUID: f0b1d2bc-08b8-4f6e-b1c6-c529024a777d Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal dir_index filetype needs_recovery sparse_super large_file Filesystem flags: signed_directory_hash Default mount options: (none) Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 15808608 Block count: 63111168 Reserved block count: 0 Free blocks: 2449985 Free inodes: 15799302 First block: 0 Block size: 4096 Fragment size: 4096 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 8208 Inode blocks per group: 513 Filesystem created: Mon Feb 15 08:07:01 2010 Last mount time: Fri May 21 19:31:30 2010 Last write time: Fri May 21 19:31:30 2010 Mount count: 5 Maximum mount count: 29 Last checked: Mon May 17 14:52:47 2010 Check interval: 15552000 (6 months) Next check after: Sat Nov 13 14:52:47 2010 Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 Default directory hash: half_md4 Directory Hash Seed: d0363517-c095-4f53-baa7-7428c02fbfc6 Journal backup: inode blocks Journal size: 128M

  Read the article

• How to verify TRIM/discard on encrypted swap?

  - by svarni

  I am using an encrypted swap partition via ecryptfs-setup-swap on my Ubuntu 13.04 computer using a SSD. I have manually set up trim for my ext4 root partition (simply by adding the "discard" option in /etc/fstab). I also manually ran fstrim on the root partition prior to booting and using dstat I saw that for a few seconds several GB/s of data have been written to the disk. That was presumably the effect of the trim command. These high writerates are reproducable by deleting huge files and have not occured before setting up trim, so I take them as evidence for working trim/discard. Manually enabling trim on my root partition has stopped the wearout of my precious new disk from 365 used reserved blocks (out of 6176 total) within three months down to 0 additional used reserved blocks within three additional months (data from SMART attributes). Because I want to minimize the wearout of my SSD I now would like to know whether my swap partition (which is encrypted using ecryptfs-setup-swap) also makes use of the trim/discard option. I tried sudo swapon -d -v /dev/mapper/cryptswap1 but did not receive particular information ("-v") about whether trim/discard ("-d") was applied. If unsupported, i would expect a message. Then I tried sudo dd if=/dev/sda6 count=1 BS=1M | xxd | less directly after booting and when no swapspace was used but I saw not only zeroes. I assume, when looking at freshly trimmed regions, the disk would send zeroes instead of reading random sectors (and according to some forums, (unencrypted) swap space is trimmed once upon boot). Long story short: Are there any ideas on how to test if trim is effectively used for my encrypted swap? And if not, any ideas on how to - at least manually, for once - trim the whole swap space? I wouldn't want to tinker with the partition itself, because I dont know if it needs to be reinitialized as (encrypted) swap - I dont want to be left with an unbootable system :)

  Read the article

• SSD as primary or secondary drive on a small Linux server?

  - by Alex Martelli

  I'm pensioning off my 10-years-old home server and replacing it with an Ubuntu 10.04 box. The two storage devices are a Western Digital Caviar Green 2.0TB HD and an Intel X25-M 34nm Gen 2 80GB SATA II 2.5inch SSD (the box has 8GB RAM and an i5 750, if it matters). I don't care much about boot times (since I don't plan to reboot all that often;-); the main frequent, performance-demanding task will be (re)building large open source C or C++ software packages from sources (as an open source contributor, I do that often). So, I thought I'd keep the SSD as the secondary drive and the HD as the primary one, using the SSD mostly for the files that can otherwise demand a lot of seeking (esp. in a parallel make). However, the friendly vendor (perhaps more experienced in Windows systems than in Linux ones) thinks the "normal" way to configure the machine would be with the SSD as the primary drive. I'm pretty rusty on configuring and tuning systems, so, I thought I'd better double check on SuperUser... thanks in advance for advice about this choice!

  Read the article

• Extending partition on linux gparted but not more space in the vm

  - by Asken

  I have a vm test installation of a linux running a build server. Unfortunately I just pressed ok when adding the disk and ended up with an 8gb drive to play with. Well into the test the builds are consuming more and more space, of course. The vm drive was resized to 21gb and using gparted I expanded the drive partitions and that all worked fine but when I go back into the console and do df there's still only 8gb available. How can I claim the other 13gb I added? fdisk -l Disk /dev/sda: 21.0 GB, 20971520000 bytes 255 heads, 63 sectors/track, 2549 cylinders, total 40960000 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0006d284 Device Boot Start End Blocks Id System /dev/sda1 * 2048 499711 248832 83 Linux /dev/sda2 501758 40959999 20229121 5 Extended /dev/sda5 501760 40959999 20229120 8e Linux LVM vgdisplay --- Volume group --- VG Name ct System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 2 Open LV 2 Max PV 0 Cur PV 1 Act PV 1 VG Size 19.29 GiB PE Size 4.00 MiB Total PE 4938 Alloc PE / Size 1977 / 7.72 GiB Free PE / Size 2961 / 11.57 GiB VG UUID MwiMAz-52e1-iGVf-eL4f-P5lq-FvRA-L73Sl3 lvdisplay --- Logical volume --- LV Name /dev/ct/root VG Name ct LV UUID Rfk9fh-kqdM-q7t5-ml6i-EjE8-nMtU-usBF0m LV Write Access read/write LV Status available # open 1 LV Size 5.73 GiB Current LE 1466 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 252:0 --- Logical volume --- LV Name /dev/ct/swap_1 VG Name ct LV UUID BLFaa6-1f5T-4MM0-5goV-1aur-nzl9-sNLXIs LV Write Access read/write LV Status available # open 2 LV Size 2.00 GiB Current LE 511 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 252:1

  Read the article

• CPU not working on a specific motherboard

  - by Shaman

  I'm making a computer for someone and I met a weird problem. The CPU that I have doesn't work on this motherboard. The CPU is an Intel Pentium D 925 and the motherboard is an ECS G41T-M6, which in theory should work together. The only thing reused is the power source(400W). When I start the computer, the fans start, and that's it. The BIOS doesn't boot. I tried my own power source (600W Corsair) and nothing. Removed the RAM, no warning. In desperation I tried the last thing, swaped my own CPU with this one (Core2Duo E7200). Lo and behold, it worked. Both. The Core2Duo worked on the ECS with the old power source and the RAM that I used in the first place, and the Pentium D worked on my Gigabyte G31M-ES2L. What I discovered was that the Pentium D didn't receive power on the ECS, because I tried running it without the cooler and it remained at room temperature. On a side note, I also removed the HDDs just in case. So, in conclusion, any ideas? I can't return it, and I can still use it to upgrade another PC, but I would really prefer not to buy another CPU if possible.

  Read the article

• Aging SBS needs updates / Thoughts for one-off, off-line complete backup?

  - by tcv

  Hey guys, So, we checked out the status of an SBS 2003 at one of our more recent, spend-averse clients and found it to be woefully out-of-date. Scary out of date. I think it's running IE2. Ok, maybe not that far back. Anyway, I was thinking that I could use some kind of disk-imaging software to image the four IDE drives within and, in the event the server gets some kind of Update Induced Indigestion, I could completely restore. Usually my go-to software for this is Acronis, but my client will likely balk at a $500 price tag for a one-off backup with their server product. I had thought we could use the boot media from, say, Backup & Recovery 10 to take an off-line image of all the drives. According to their CHAT tech support, however, it will not work. I pressed for the technical reasons and they said they'd email me. They haven't emailed me. They still might. This server is running SBS 2003, pre sp2. It's got four IDE disks. One is a Basic disk, which contains the O/S. The others are bound as a dynamic disk. You might ask: "Don't they already have backup software?" They do! Backup Exec, a very low-end version that won't even do VSS. I don't know much about BE, but it seems to me that if the worst were to happen, it would mean building a new server O/S, installing BE (if the media is available), then restoring. Would it even work? I can take the system down for hours to do a backup and my goal here is a pretty dead-simple restore if the worst happens. Any and all suggestions are exciting. m

  Read the article

• Is there a clean way to obtain exclusive access to a physical partition under Windows?

  - by zneak

  Hey guys, I'm trying, under Windows 7, to run a virtual machine with VMWare Player from an OS installed on a physical partition. However, when I boot the virtual machine, VMWare Player says that it couldn't access the physical drive for writing. This seems to be a generally acknowledged problem in the VMWare community, as Windows Vista introduced a compelling new security feature that makes it impossible to write to a raw drive without obtaining exclusive access to it first. I have googled the issue and found a few workarounds. However, the clean ones seem to only work on whole physical disks, and not on partitions. So I would be left with the dirty solution. In short, it meddles with the MBR to erase any trace of the partitions to use, makes Windows forget about them, then restores the MBR so we can launch the VM. I'm not sure I want to do that. Is there a way to let VMWare acquire exclusive access to the partition without requiring me to nuke it away? What I'd be looking for, I suppose, is a way to put just partitions offline instead of whole physical drives.

  Read the article

• VirtualBox doesn't see raw partitions

  - by smbear

  What I want to achieve is to set up virtual machine with VirtualBox. Host OS is Windows 7 Home Premium, guest will be (k)Ubuntu 12.04 on a raw partition. The first problem is that when I issue following command: VBoxManage.exe internalcommands listpartitions -rawdisk \\.\PhysicalDrive0 I get following result: Number Type StartCHS EndCHS Size (MiB) Start (Sect) 1 0xee 0 /0 /1 1023/254/63 715404 1 I'm guessing that VirtualBox is unable to see my partitions. If I use diskpart tool, then all partitions are listed correctly (note Polish language version of Windows): DISKPART> select disk 0 Obecnie wybranym dyskiem jest dysk 0. DISKPART> list partition Partycja ### Typ Rozmiar Przesuniecie ------------- ---------------- ------- ------------ Partycja 1 System 200 MB 1024 KB Partycja 2 Zarezerwowany 128 MB 201 MB Partycja 3 Podstawowy 139 GB 329 MB Partycja 5 Nieznany 4883 KB 140 GB Partycja 6 Podstawowy 50 GB 140 GB Partycja 7 Podstawowy 484 GB 190 GB Partycja 4 Odzyskiwanie 24 GB 674 GB Additional note: my PC is using EFI to boot OS. Basing on the results listed above, I believe that: I messed up with my partition table. Something is wrong with VirtualBox. Can anyone help with this issue?

  Read the article

• Port to use CentOS init.d functions

  - by jcalfee314

  What are good equivalent centos commands using functions in /etc/init.d/functions such as daemon to perform the following tasks? STARTCMD='start-stop-daemon --start --exec /usr/sbin/swapspace --quiet --pidfile /var/run/swapspace.pid -- -d -p' STOPCMD='start-stop-daemon --stop --oknodo --quiet --pidfile /var/run/swapspace.pid' It looks like daemon will work for the start command and killproc is used for the stop command. . /etc/init.d/functions pushd /usr/sbin daemon --pidfile /var/run/swapspace.pid /usr/sbin/swapspace . /etc/init.d/functions killproc -p $(cat /var/run/swapspace.pid) Would the --oknodo be needed in the CentOS env (the swap file is really only boot-time)? "oknodo - Return exit status 0 instead of 1 if no actions are (would be) taken." I don't see quiet in daemon or killproc, I can't imagine that it would matter though. The original start-stop-daemon for swapspace seems to have both -p and --pidfile (the same command). That must be an error. Did I miss anything? Any idea why daemon not create the pid file?

  Read the article

• In Windows 7 power management, is it possible to set different sleep settings for different SATA disks?

  - by Ben Voigt

  I'm having an issue with Windows 7 either freezing up or generating a BSOD coming out of sleep. I suspect that it is related to my boot/OS drive, an OCZ Vertex SE SSD, because numerous other Vertex users have reported sleep problems. Notably, if I put the computer to sleep, it almost always wakes correctly. If it goes to sleep after a timeout, it almost always BSODs. I disabled timed sleep and now it freezes when left unattended. My next step is to disable "Put hard disks to sleep after X minutes", but I'd like to change this setting only for the SSD and not for the rotating data disks, which I would like to spin down normally. Does anyone know a place to configure sleep on a per-disk basis? I don't need to set different timeouts on different disks (although that would be nice), simply setting "this disk sleeps" and "sleep is disabled for this disk" would be great. Additional system information: Windows 7 Ultimate x64, Core i5 - P55 chipset, Intel RST drivers are installed. One SSD, two rotating HDD, and a DVD-RW drive are all connected to the Intel SATA ports. I could potentially move some of these to my motherboard's other SATA controller if that would help.

  Read the article

• Computer hangs at BIOS screen. Cannot enter setup.

  - by d2jxp

  I have an HP Pavilion a6500f (it's a year out of warranty) and it's hanging on the blue HP BIOS screen. If I mash F10 while it's starting up, it will say "Entering Setup..." but I will see no results. It will hang there and not do anything. If I actually wait until I can see the screen and then hit F10, there's no response at all and the computer will sit at the BIOS menu. I've dusted and cleaned it out, reseated the memory, switched the RAM slots, and reset the CMOS battery using the reset jumper. I'm out of ideas. I'm pretty sure it's not a hard drive issue, since my problem is at the BIOS. After this post, I'll disconnect the hard drive and try to just boot without it. Anyone have any other ideas? Edit: Okay, so I tried disconnecting the hard drive and now I can get back into the BIOS. I reconnected it and I'm locked out again. So the problem is my hard drive.. I guess I should delete this post unless someone has any ideas as to what's wrong with the drive?

  Read the article

• Windows 7 Taskbar resets on every login

  - by Arne Mertz

  I like to reorder my Taskbar a bit, other than the Windows 7 default is. I use two "rows", the lower is for quicklaunch and other toolbars: This works perfectly, as long as I don't log off from the computer. Every time I log in, Windows 7 has messed up/reset the toolbar positions like this: So I have to drag them into position again and again, every morning. Fixing the taskbar positions won't help, I tried to google for the problem but it does not seem to be very common. Does anyone recognize that problem and has a solution? Update: This is not the AutoLogon bug. AutoLogon is off. We have installed Novell at our company, and it does not matter wether I log directly onto the Novell network or only to the computer first and to Novell later. Update2: I get the same issue when I logon without Novell, i.e. when I log on only to the computer. When I boot in safe mode, the taskbar looks essentially the same: Update3: KB979155 says it's "not applicable to my system". Creating a neew user is not an option since I don't have the admin privileges to do that - I have almost any other local admin privileges, though.

  Read the article

• How is network mounted software executed?

  - by CptSupermrkt

  I would like to understand how network mounted software works. For example, at my place of work, we have a software server. Each client machine (hundreds of them) automatically mounts directories from the software server on boot. For example, a program like Matlab is installed just once on the software server, but each client machine can start up an instance of Matlab. What is going on under the hood? Let's say I run /opt/bin/matlab and /opt/ is mounted from the software server, what happens when I press Enter to execute matlab on a client machine? The process is on the client machine, and I've already narrowed down that there isn't any implicit or hidden file transfer (i.e. copying matlab to my machine temporarily for that session) by running matlab on a computer with nearly zero disk space (i.e. not enough room to transfer). Since Matlab was installed on the server, how is my client computer executing it? What mechanism is controlling this? What is happening behind the scenes?

  Read the article

• External Dell Display doesn't work with MacBook Pro (2011) after Thunderbolt Firmware Update (1.0 and 1.2)

  - by tom

  Today two Thunderbolt Firmware Updates (1.0 and 1.2) became available for my MacBook Pro (Early 2011). After installing both, my external monitor, a Dell U2713HM, does no longer work. The system detects the display, but the display shows only black. An Apple Thunderbolt display works fine and a MacBook Air can use the Dell monitor without problems. My MacBook Pro can use the Dell monitor just fine when I boot from a USB stick. Therefore, clearly the Thunderbolt Firmware Update seems to be the problem. Does anyone have the same problem? Any solutions or workarounds? I guess there is no way to remove a Thunderbolt Firmware Update once it's installed, right? Update 24.10.2013: Is there no one else with this problem? In the meantime I tried three different cables – none worked. My colleague with the same generation MacBook Pro also can't use my display after installing the firmware update. All colleagues with MacBook Airs and newer MacBook Pros (all didn't receive the firmware update) can use the display. Update 29.10.2013: Wow, ok today my new MacBook Pro Retina 13' (Late 2013) arrived. Guess what, I cannot use the display with it. Only HDMI works – not with the full resolution.

  Read the article

• Linux RAID: Replacing Failed Drive...permanantly

  - by user137519

  Okay, odd question here. I have a server with RAID 5. A drive failed, in a really physically in a really odd way. On the machine it boots and is seen by the BIOS but...no partition can be seen on the drive consistantly (in and out). 2 out of 3 drives working...I made new spare disk and added it, RAID 5 rebuilt clean. All appears well but...when I reboot it keeps trying to use the 2nd drive which doesn't give any partition data, so of course the RAID 5 gets 2 out of 3...again. The status of my drive is as follows: /dev/sda2:Good /dev/sdb2 (drive has physical problem so no partition data) bad, /dev/sdc2:good /dev/sdd2:good. Every time I reboot the mdadm system seems to keep trying to use /dev/sdb which has physical failure (although spins and is detected). /dev/sdd is the new drive I created. I added /dev/sdd to the raid and it rebuilds the raid but this action isn't memorized upon reboot so it keeps listing /dev/sda and /dev/sdc but doesn't use the perfectly good /dev/sdd until I re-add manually. I've tried removing the dead drive with the mdadm tool, but as it cannot see /dev/sdb paritions it will not fail or remove it (says partition doesn't exist). the /etc/mdadm.conf was automatically made on the original OS install which only lists: DEVICE partitions MAILADDR root ARRAY /dev/md2 super-minor=2 ARRAY /dev/md0 super-minor=0 ARRAY /dev/md1 super-minor=1 Basically just the raids to use on boot. I need to remove this semi-dead drive (/dev/sdb) but I'd prefer to know why this is happening before I do. any ideas or suggestions. I supposed I could attempt to clone/replace /dev/sdb (the partitions on drive show up, then disappear shortly after) but given the partition "chester cat" behaviour this seems risky to me and as I have a working "spare" it seems unnecessary. Thanks in advance for your insight.

  Read the article

• How to locate phpmyadmin on ubuntu

  - by Chris

  Okay, I'm usually a windows user and I write quite happily there, unfortunately (or fortunately) I have installed linux on a dual boot and having installed some software I have a question... Where is it? I installed Apache, PHP, MySQL and separately phpmyadmin, Apache is up and running, I've seen my phpinfo page and MySQL is there. MySQL is telling me that there's a database for phpmyadmin, but...erm.. I can't seem to locate it. On a windows machine the directory would be in the www directory and I'd just navigate there... localhost/phpmyadmin/ but on Ubuntu I can't find it in the equivalent. I've been to /var/www/ and there's my index.html (from apache) and my phptest.php file but no phpmyadmin. There is a phpmyadmin in /lib but that only has 2 files in it. So having rambled lots, my question is, what do I have to do to be able to navigate to the phpmyadmin index page? I realise this could fall under the description of a server related question and should be posted elsewhere but as it's software on a home system some help would be appreciated. Do I need to move some files from somewhere? Help! I really don't want to have to go back to developing on Windows as I'll be deploying to a lamp system, my learning curve will be steep.

  Read the article

• Decrease in disk performance after partitioning and encryption, is this much of a drop normal?

  - by Biohazard

  I have a server that I only have remote access to. Earlier in the week I repartitioned the 2 disk raid as follows: Filesystem Size Used Avail Use% Mounted on /dev/mapper/sda1_crypt 363G 1.8G 343G 1% / tmpfs 2.0G 0 2.0G 0% /lib/init/rw udev 2.0G 140K 2.0G 1% /dev tmpfs 2.0G 0 2.0G 0% /dev/shm /dev/sda5 461M 26M 412M 6% /boot /dev/sda7 179G 8.6G 162G 6% /data The raid consists of 2 x 300gb SAS 15k disks. Prior to the changes I made, it was being used as a single unencrypted root parition and hdparm -t /dev/sda was giving readings around 240mb/s, which I still get if I do it now: /dev/sda: Timing buffered disk reads: 730 MB in 3.00 seconds = 243.06 MB/sec Since the repartition and encryption, I get the following on the separate partitions: Unencrypted /dev/sda7: /dev/sda7: Timing buffered disk reads: 540 MB in 3.00 seconds = 179.78 MB/sec Unencrypted /dev/sda5: /dev/sda5: Timing buffered disk reads: 476 MB in 2.55 seconds = 186.86 MB/sec Encrypted /dev/mapper/sda1_crypt: /dev/mapper/sda1_crypt: Timing buffered disk reads: 150 MB in 3.03 seconds = 49.54 MB/sec I expected a drop in performance on the encrypted partition, but not that much, but I didn't expect I would get a drop in performance on the other partitions at all. The other hardware in the server is: 2 x Quad Core Intel(R) Xeon(R) CPU E5405 @ 2.00GHz and 4gb RAM $ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 32 Lun: 00 Vendor: DP Model: BACKPLANE Rev: 1.05 Type: Enclosure ANSI SCSI revision: 05 Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC 6/i Rev: 1.11 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: CD-ROM GCR-8240N Rev: 1.10 Type: CD-ROM ANSI SCSI revision: 05 I'm guessing this means the server has a PERC 6/i RAID controller? The encryption was done with default settings during debian 6 installation. I can't recall the exact specifics and am not sure how I go about finding them? Thanks

  Read the article

• Random keyboard malfunction - happens in Vista and XP

  - by Stupefy101

  For some weird reason, some of my keyboard keys of my deskop are acting very strangely. I don't remember a certain time when it started and I can't recognize any pattern as to when it happens and when it doesn't. The problem occurs in Windows XP, XP Safe Mode, Vista, and Vista Safe mode (I have a dual boot system) Here's what's happening: When I push the I, K, comma, or 8 keys (notice how they are all in the same column), instead of just getting that character, I get extra characters afterwards. For example, I'll push the k key and it will print "ksfda", pushing "I" gives me "IWREQ", comma gives me ", xvcz", pushing 8 gives me "82431". There are a couple things that I have noticed: It does not happen every time I push the key It happens in all OS and applications I have tested The characters coming after the desired ones are in the same pattern (column order: 2, 4, 3, 1 from the left of the keyboard in the same row as the key pressed. Pressing "]" will sometimes give me "]t", and if done in Notepad, will bring up the "Find" dialog window I cannot seem to remember a specific time the problem started, although I have been defragging, using TuneUp Utilities + CCleaner, and installing lots of new programs lately.

  Read the article

• Need Help Scoping a Server to use for study (MCITP Ent Admin + SharePoint 2010)

  - by AVFamily76

  i need to study for mcitp, but i also need to study for sharepoint 2010 i have a poweredge 1850 with two single-core CPUs + two 73G drives - it kills me on electricity, so don't want to use it, and it won't do VT, but it could be one of three boxes for a lab that's cheap, but will cost a lot on electricity i was thinking . . . OPTION #1 Opteron 4170 HE (50 watt chip), 6-core, only two-bills ($200), but the board's are $250, so that's an $800 box, then get another box to dual-boot Win7/Hyper-V on the cheap...? OPTION #2 Used Quad - but how many VM's that are really banging away could it run at same time? (Server 2008r2, SQL 2008r2, Search Server) OPTION #3 Study from books and just get one box that can run two VM's at same time, even if slowly. the last time i had and used a home lab was five years ago when i had a DC, SQL, Exchange and business app box, that's where i got my server skills was just banging on it for four years, but didn't read any books, so now i have to get certified and know the material, and just am not sure how much attention i should pay to the box i use versus the studying time and reading. sorry it's a subjective question, and am obviously open to all sorts of abuse here, but hope you can tell me also how many VM's i can run at the same time given what they'll be doing (SQL and SharePoint FAST search server are resource hungry) thanks!

  Read the article

• disk space keeps filling up on EC2 instance with no apperent files/directories

  - by sasher

  How come os shows 6.5G used but I see only 3.6G in files/directories? Running as root on an Amazon Linux AMI (seems like Centos), lots of free memory available, no swapping going on, no apparent file descriptors issue. The only thing I can think of is a log file that was deleted while applications append to it. Disk space usage is slowly but continuously rising towards full capacity (~1k/min with very small decreases from time to time) Any explanation? Solution? du --max-depth=1 -h / 1.2G /usr 4.0K /cgroup 22M /lib64 11M /sbin 19M /etc 52K /dev 2.1G /var 4.0K /media 0 /sys 4.0K /selinux du: cannot access /proc/14024/task/14024/fd/4': No such file or directory du: cannot access<br/> /proc/14024/task/14024/fdinfo/4': No such file or directory du: cannot access /proc/14024/fd/4': No such file or directory du: cannot<br/> access/proc/14024/fdinfo/4': No such file or directory 0 /proc 18M /home 4.0K /logs 8.1M /bin 16K /lost+found 12M /tmp 4.0K /srv 35M /boot 79M /lib 56K /root 67M /opt 4.0K /local 4.0K /mnt 3.6G / df -h Filesystem Size Used Avail Use% Mounted on /dev/xvda1 7.9G 6.5G 1.4G 84% / tmpfs 3.7G 0 3.7G 0% /dev/shm sysctl fs.file-nr fs.file-nr = 864 0 761182

  Read the article

• Notebook display problem (multiplication)

  - by SubniC

  Hi, I'm having some troubles with the display of a LG E500 notebook. The thing is that without any known reason the display starts to show the screen divided in eigth parts and each part show the display image as if I had a matrix of eigth displays :) I thought it could be some kind of refresh rate problem or driver related, but it is happening at boot-up as well and the BIOS. I got the computer completely unassambled yesterday and I check all the wires and connectors looking for something broken or unconected, but without luck... You can see a picture here of the problem (sorry for the low quality, but I think it illustrate the problem. EDIT 1: I uploaded a new pictrue, here you cans ee the problem better :) There are three horizontal lines that you can see just between the windows. You can see the grey line at the first moment you turn on the computer and the after the duplicated screens show up just like if they where arranged over a grid (over the horizontal lines...) I hope it makes any sense. Do you know what could be happening? or can you tell me what would you do? Thank you very much for your help.

  Read the article

< Previous Page | 436 437 438 439 440 441 442 443 444 445 446 447  | Next Page >