Search Results

Search found 13930 results on 558 pages for 'dev center'.

Page 440/558 | < Previous Page | 436 437 438 439 440 441 442 443 444 445 446 447  | Next Page >

• Disk IO slow on ESXi, even slower on a VM (freeNAS + iSCSI)

  - by varesa

  I have a server with ESXi 5 and iSCSI attached network storage(4x1Tb Raid-Z on freenas 8.0.4). Those two machines are connected to each other with Gigabit ethernet. The raid-z volume is divided into three parts: two zvols, shared with iscsi, and one directly on top of zfs, shared with nfs and similar. I ssh'd into the freeNAS box, and did some testing on the disks. I used ddto test the third part of the disks (straight on top of ZFS). I copied a 4GB (2x the amount of RAM) block from /dev/zero to the disk, and the speed was 80MB/s. Other of the iSCSI shared zvols is a datastore for the ESXi. I did similar test with time dd .. there. Since the dd there did not give the speed, I divided the amount of data transfered by the time show by time. The result was around 30-40 MB/s. Thats about half of the speed from the freeNAS host! Then I tested the IO on a VM running on the same ESXi host. The VM was a light CentOS 6.0 machine, which was not really doing anything else at that time. There were no other VMs running on the server at the time, and the other two "parts" of the disk array were not used. A similar dd test gave me result of about 15-20 MB/s. That is again about half of the result on a lower level! Of course the is some overhead in raid-z - zfs - zvolume - iSCSI - VMFS - VM, but I don't expect it to be that big. I belive there must be something wrong in my system. I have heard about bad performance of freeNAS's iSCSI, is that it? I have not managed to get any other "big" SAN OS to run on the box (NexentaSTOR, openfiler). Can you see any obvious problems with my setup?

  Read the article

• Accidentally mounted a ReiserFS drive as MBR on my windows box - how do I recover?

  - by Ryan

  I had a WD Netcenter with a 160GB drive that kept dropping off the network. I opened up the enclosure and removed the hard drive, connected to a Windows box without knowing the drive used ReiserFS.... When mounting on the Windows box, I chose "MBR" as filesystem. 70GB of data corrupted: 90% of data is word documents, excel spreadsheets, and jpg's - all mission critical. Attempted recovery on Linux box (ubuntu) using TestDisk: I could see the container, but couldn't get anything out – according to TestDisk this was because I chose "none" as filesystem. Attempted recovery using Nucleus Kernel Recovery for windows: 98% of what was recovered is incomplete and/or unusable. I need to know if a way exists to recover or rebuild original ReiserFS MBR, or what tools/techniques might give me the best results in recovering the data. Found a Windows version of TestDisk and I ran it yesterday - here are the results: TestDisk 6.14-WIP, Data Recovery Utility, May 2012 Christophe GRENIER <[email protected]> http://www.cgsecurity.org Disk /dev/sda - 160 GB / 149 GiB - CHS 19457 255 63 The harddisk (160 GB / 149 GiB) seems too small! (< 519 GB / 483 GiB) Check the harddisk size: HD jumpers settings, BIOS detection... The following partitions can't be recovered: Partition Start End Size in sectors > ReiserFS 3.6 62 241 8 19458 0 18 311581568 ReiserFS 3.6 62 248 55 19458 8 2 311581568 ReiserFS 3.6 62 254 37 19458 13 47 311581568 ReiserFS 3.6 63 6 28 19458 20 38 311581568 ReiserFS 3.6 63 13 11 19458 27 21 311581568 ReiserFS 3.6 63 21 43 19458 35 53 311581568 ReiserFS 3.6 63 27 41 19458 41 51 311581568 ReiserFS 3.6 63 37 35 19458 51 45 311581568 ReiserFS 3.6 63 54 20 19458 68 30 311581568 ReiserFS 3.6 63 76 26 19458 90 36 311581568

  Read the article

• How to enable Ipv6 on my ubunutu 11.04 virtual machine

  - by liv2hak

  I have installed 3 VM's on my PC.(Ubuntu 11.04).I want to setup an IPV6 network to review and test some of the IPV6 tools like NDPMonitor.(monitors ICMP messages of Neighbour Discovery Protocol.) IP v6 addresses are as follows. linux_router - fe80::a00:27ff:fed5:f7e9/64 labhack1 - fe80::a00:27ff:fed2:8bd1/64 labhack2 - fe80::a00:27ff:fed7:2f2d/64 The below commands have been run on both linux_router and labhack1. sudo ip r a 2001:468:181:f100::/64 dev eth0 sudo vim /etc/radvd.conf /file looks like below./ interface eth0 { AdvSendAdvert on; /*means that we are sending out advertisments.*/ MinRtrAdvInterval 5; /*these options control how often advertisments are sent*/ MaxRtrAdvInterval 15; /*these are not mandatory but valueable settings.*/ prefix fe80::a00:27ff::/64 { AdvOnLink on; /*Says to the host everyone sharing this prefix is on the sam local link as you.*/ AdvAutonomous on; /*Says to a host: "Use this prefix to autoconfigure your address"*/ }; }; sudo sysctl -w net.ipv6.conf.all.forwarding=1 I try to do a ping6 -I eth0 fe80::a00:27ff:fed5:f7e9 I get Destination unreachable: Address unreachable.I am not sure what I am doing wrong here.I am a beginner at linux administration.Basically I think I am missing whatever is analogous to physically connecting VM's.Any help that would point me in the right direction would be greatly appreciated.

  Read the article

• MySQL Server Is Slow

  - by user2853965746

  I have two MySQL servers and one was just recently setup. The one I just recently setup is a bit slower than my older one, which kind of bothers me because I don't want my clients to be upset with the speed difference when I launch the new one. The older server runs on Ubuntu (~13.04 I believe) and the new one is on Debian 6. Both servers are 2GB ram, but my newer server is has an SSD, so I thought it might be the same speed if not faster. Anyway, the speed difference isn't too much (both are still under a second, but still noticeable). Whenever I select 50 rows from the user table on my older server (SELECT * FROM users LIMIT 50), I get the results in 0.003 s. There is 100,000+ accounts in that table. Whenever running the same command on the same table with only six dev accounts, it takes 0.069 s. It may not seem like a lot, but it's noticeable when you're used to a fast response. I added skip-name-resolve to the config and it didn't seem to help. Basically I'm asking if anyone knows what can cause a MySQL server to be slow in Debian 6? Should I just drop it and switch to Ubuntu like the older server (I don't think the OS is the problem, but you never know)? The older server is under a lot of use too, it's used a lot for web api's on my website. A lot of connections and stuff, and it still remains fast.

  Read the article

• some windows 8 metro (modern UI) apps don't open, but live tiles DO work

  - by DiegoDD

  Some of my default windows 8 metro (modern UI) apps don't work properly, the apps are the Weather and the News apps. when I open them, I only get the loading screen, that is, the big colorful screen with the logo in the center, and the "loading" spinning dots. They just keep like that forever and never actually open. There are no error messages or anything. The strange this is that the live tiles for those apps DO work and show current information. current weather for my location (saved before they started failing) and current news. Both apps did work well in the past, and every other default windows 8 app I've tried work well (both live tiles and the app itself). Every other non-default apps that I've downloaded still work correctly, so the problem so far is only with those two apps. (weather and news). I really don't know since when exactly they started to fail because I really don't use them (or any metro app) that often, so I can't recall if I did something like installing some other app, either metro or regular, or messed with some drivers, etc. they simply don't open now, but they DID work before. any ideas?

  Read the article

• VNC server failed to start CentOS

  - by Shaun

  I followed a tutorial on how to install and get VNCserver to run on CentOS 6 (since freenx isnt supported yet) and I keep getting Starting VNC server: 1:user [FAILED] How do I figure out whats going on here? Im new to Linux/CentOS and im trying to get RDP going so I can step away from SSH as much as possible (you know us Windows users love our pretty GUI's). So, where is the error log at and how do I find it? Or maybe someone else has experienced this and knows the solution based on the simple error given? After running in debug mode, here is my error + . /etc/init.d/functions ++ TEXTDOMAIN=initscripts ++ umask 022 ++ PATH=/sbin:/usr/sbin:/bin:/usr/bin ++ export PATH ++ '[' -z '' ']' ++ COLUMNS=80 ++ '[' -z '' ']' +++ /sbin/consoletype ++ CONSOLETYPE=pty ++ '[' -f /etc/sysconfig/i18n -a -z '' -a -z '' ']' ++ . /etc/profile.d/lang.sh ++ unset LANGSH_SOURCED ++ '[' -z '' ']' ++ '[' -f /etc/sysconfig/init ']' ++ . /etc/sysconfig/init +++ BOOTUP=color +++ RES_COL=60 +++ MOVE_TO_COL='echo -en \033[60G' +++ SETCOLOR_SUCCESS='echo -en \033[0;32m' +++ SETCOLOR_FAILURE='echo -en \033[0;31m' +++ SETCOLOR_WARNING='echo -en \033[0;33m' +++ SETCOLOR_NORMAL='echo -en \033[0;39m' +++ PROMPT=yes +++ AUTOSWAP=no +++ ACTIVE_CONSOLES='/dev/tty[1-6]' +++ SINGLE=/sbin/sushell ++ '[' pty = serial ']' ++ __sed_discard_ignored_files='/\(~\|\.bak\|\.orig\|\.rpmnew\|\.rpmorig\|\.rpmsave\)$/d' + '[' -r /etc/sysconfig/vncservers ']' + . /etc/sysconfig/vncservers ++ VNCSERVERS='1:larry 2:moe 3:curly' ++ VNCSERVERARGS[1]='-geometry 800x600' ++ VNCSERVERARGS[2]='-geometry 640x480' ++ VNCSERVERARGS[3]='-geometry 640x480' + prog='VNC server' + RETVAL=0 + case "$1" in + start + '[' 0 '!=' 0 ']' + . /etc/sysconfig/network ++ NETWORKING=yes ++ HOSTNAME=vps.binaryvisionaries.com ++ DOMAINNAME=server.name ++ GATEWAYDEV=venet0 ++ NETWORKING_IPV6=yes ++ IPV6_DEFAULTDEV=venet0 + '[' yes = no ']' + '[' -x /usr/bin/vncserver ']' + '[' -x /usr/bin/Xvnc ']' + echo -n 'Starting VNC server: ' Starting VNC server: + RETVAL=0 + '[' '!' -d /tmp/.X11-unix ']' + for display in '${VNCSERVERS}' + SERVS=1 + echo -n '1:larry ' 1:larry + DISP=1 + USER=larry + VNCUSERARGS='-geometry 800x600' + runuser -l larry -c 'cd ~larry && [ -r .vnc/passwd ] && vncserver :1 -geometry 800x600' + RETVAL=1 + '[' 1 -eq 0 ']' + break + '[' -z 1 ']' + '[' 1 -eq 0 ']' + failure 'vncserver start' + local rc=1 + '[' color '!=' verbose -a -z '' ']' + echo_failure + '[' color = color ']' + echo -en '\033[60G' + echo -n '[' [+ '[' color = color ']' + echo -en '\033[0;31m' + echo -n FAILED FAILED+ '[' color = color ']' + echo -en '\033[0;39m' + echo -n ']' ]+ echo -ne '\r' + return 1 + '[' -x /usr/bin/plymouth ']' + /usr/bin/plymouth --details + return 1 + echo + '[' 1 -eq 98 ']' + return 1 + exit 1

  Read the article

• Problem building PHP extension module

  - by tixrus

  I'm trying to get GD into my PHP. So I compiled it, made php.ini point to it, restarted apache etc. But no GD. So in apache error log it says PHP Warning: PHP Startup: gd: Unable to initialize module\nModule compiled with module API=20060613\nPHP compiled with module API=20090115\nThese options need to match\n in Unknown on line 0 So a bit of googling says I should not use the phpize I have before configuring and making these. I should use a new one called phpize5. I surely don't have any such thing. Unless its packed up inside something else in my php5.3. distro. Where do you get it. In Ubuntu I could just run sudo apt-get install php-dev, (apparently) and it would just appear by magic. At least that's what the webpage said. Unfortunately I am running MacOSX version Leopard. How can I build this GD module so that it will match the API number in my PHP?

  Read the article

• SQL Server 2005 SP3 on Windows 7 - No Management Studio

  - by Mike Thomas

  I've been trying for a day and a half now to get SQL Server 2005, DEV edition, to work on Windows 7, 64 bit prof. I install from the disk, then run SP 3. I get a failure on the Client Components section of the Installation Progress along with this vague message - Product : Client Components Product Version (Previous): 1399 Product Version (Final) : Status : Failure Log File : C:\Program Files\Microsoft SQL Server\90\Setup Bootstrap\LOG\Hotfix\SQLTools9_Hotfix_KB955706_sqlrun_tools.msp.log Error Number : 1712 Error Description : MSP Error: 1712 One or more of the files required to restore your computer to its previous state could not be found. Restoration will not be possible. I've uninstalled all Visual Studio and tried to make this as clean as possible, and have read a lot of the blog posts, but am really at my wits end about this. I am not a DBA, but I use SQL Server all the time when coding and testing apps. Does anyone have any ideas as to where I can get this sorted out? I've been ati this for a long time and have never encountered an installation as bad as this one. Thanks Mike Thomas

  Read the article

• Cannot Kill Process in Vista 64

  - by JanSolo

  Hi I have a weird situation where a Zombie process is causing my Vista64 Dev machine to become useless. I use Incredibuild 3.40 to distribute builds of a large software product that I work on. Occasionally, a build will fail and a Zombie process is left behind. The process holds a handle to a file that is needed by the build system to retry the build. Since I cannot kill the process, the handle remains open and I cannot build my code at all. I've tried TargetManager and ProcessExplorer, but neither can kill this process. It gets worse; since Vista cannot kill all its processes, my PC refuses to shut down correctly, requiring a hard reboot after each failed build. Is there a way to really-really-kill a process in Vista? Or maybe a way to force a file handle to close? Any help is appreciated. Cheers Jan. EDIT: This is still occurring. I've used Lockhunter (which appears to successfully unlock the file handle), but retrying the build still fails because the (now unlocked) file cannot be deleted. Explorer and Lockhunter both fail to delete the file. LockHunter also tells me that there are no processes that hold handles to it. Basically, nothing owns it, but you still cant delete it. This sucks.

  Read the article

• How to find out which program a default beep is coming from in Windows 7?

  - by leeand00

  There's a "default beep" (as defined in System Sounds) that emanates from my computer every so often. It kind of goes like this (where each number is a "default beep" sound): 1, 2, 3, 4, 5. So there's a distinct pattern to it. I thought I had this figured out a way to figure out what was happening by going to Control Panel-Ease of Access-Ease of Access Center-Replace sounds with visual cues But that just isn't the case. Whichever window I click on, that one displays the visual queue when this happens. It's driving me crazy, and I can't figure out which program is causing this. Update: it appears to only happen on one user profile on the computer...does that help? Update 2: Discovered that this sound was coming from a utility on my laptop called ASUS NB Probe; I'm certain that it is emanating from this program because the error message displayed by it changes in sync with the sound playing. Apparently the S.M.A.R.T. feature of my hard drive was reporting an issue. It displays the issue for a brief second and then makes it disappear, I'll have to keep watching it to see what it says, but I believe is says something about a read. I have an external hdd connected with eSATA to a container of sorts (BlacX) that you can plug two hdds into. I have one hdd attached and it's a Western Digital WD1001FALS - 00E8B0 Thanks again! Now I'm off to go around the Internet and report on this...since I posted it so many places!

  Read the article

• Fatal Execution Engine Error on the Windows2008 r2, IIS7.5

  - by user66524

  Hi Guys We are running some asp.net(3.5) applications on the Windows2008 r2, IIS7.5. Recently we got some event logs so difficult, we have not idea hope some guys can help. 1.EventID: 1334 (9-1-2011 8:41:57) Error message An error occurred during a process host idle check. Exception: System.AccessViolationException Message: Attempted to read or write protected memory. This is often an indication that other memory is corrupt. StackTrace: at System.Collections.Hashtable.GetEnumerator() at System.Web.Hosting.ApplicationManager.IsIdle() at System.Web.Hosting.ProcessHost.IsIdle() 2.EventID: 1023 (9-1-2011 19:44:02) Error message .NET Runtime version 2.0.50727.4952 - Fatal Execution Engine Error (742B851A) (80131506) 3.EventID: 1000 (9-1-2011 19:44:03) Error message Faulting application name: w3wp.exe, version: 7.5.7600.16385, time stamp: 0x4a5bcd2b Faulting module name: mscorwks.dll, version: 2.0.50727.4952, time stamp: 0x4bebd49a Exception code: 0xc0000005 Fault offset: 0x0000c262 Faulting process id: 0x%9 Faulting application start time: 0x%10 Faulting application path: %11 Faulting module path: %12 Report Id: %13 4.EventID: 5011 (9-1-2011 19:44:03) Error message A process serving application pool 'AppPoolName' suffered a fatal communication error with the Windows Process Activation Service. The process id was '2552'. The data field contains the error number. 5.some info: we got the memory.hdmp(234MB) and minidump.mdmp(19.2) from control panel action center but I donot know how to use that :(

  Read the article

• High latency issue for web service call from amazon aws ec2 to local server

  - by SibzTer

  We have a legacy web application that is running in our data center on premises located in Houston. We have a developed a new .net 4 based web application in order to provide new features to customers. The new web application is hosted in amazon aws ec2 environment (N. Virginia region us-east-1b zone). In order to get seamlessly integrate with the legacy application the new web application makes web service calls to retrieve data. We are seeing an unusually high latency time in the order of 5+ seconds for these web service calls. The exact same web service call returns in less than a second on our local PCs (which makes sense given physical proximity to the actual server). The weird part is that we have developers in California who also have the same milliseconds response time. We are testing the web service response using third party tools such as SoapUI, Google Chrome extensions such as Advanced REST Client, Postman REST Client, etc. As if this wasnt weird enough, we have noticed the same low latency from certain other ec2 instances while testing which are in the same region and availability zone as well. If we experienced the high latency consistently from all the ec2 instances I could understand. But there is something else going on. Comparing the various stats and results between the low latency and high latency ec2 servers do not show any significant differences: ping (constant 40ms), tracert, winmtr, etc. We have instances that are in the VPC as well. So I tried both the public and private IP address of the web service host server and that didnt make a difference either for the above results. We need to resolve this latency issue as this is causing the resulting web pages to load very slowly (almost 15+ seconds which is simply unacceptable). The ec2 instances have Windows Server Datacenter 64 bit. Let me know if there is any other infor I can provide to help diagnose this.

  Read the article

• With Ubuntu 9.10, my DVD keeps spinning up

  - by Ken

  I have Ubuntu 9.10 on my Intel Mac Mini. When there's a DVD in the drive, and even if there's no program open at all (just looking at the desktop), every minute or so the disc spins up with a loud whirring noise, and I can hear it cranking the motor to seek across the disc. How do I find out what's causing this? And how can I make it stop? Thanks! EDIT: I straced nautilus, and saw nothing it's doing directly, even when the disc spins up. It does poll inotify regularly, but I don't know how to trace what it's watching, or if that's even how it receives disc-inserted notifications. It doesn't call inotify_add_watch when I insert a disc or mount it (or eject or umount), but it could be watching all of /dev already or something like that. Of course, a DVD is mounted read-only, so whether it's inotify or something else, it should never need to poll anything on that. And if it is inotify, it's happening in the kernel, and the kernel should really never need to poll a device it's mounted to check for notifications.

  Read the article

• Why can't Logman start?

  - by Bill Paetzke

  I'm setting up my first logman counter. But it's not working! There is some file or folder permissions problem. Or maybe I wrote the create-counter statement wrong. Here's my counter commands: logman create counter BillTest -si 30 -v nnnnnn -max 200 -o "C:\Temp" -c "\Processor(*)\*" "\Memory(*)\*" "\LogicalDisk(*)\*" logman start BillTest The first command works. It says counter creation successful. The second command fails: Collection "BillTest" did not start, check the application event log for any errors Here's the error in the Event Viewer: The service was unable to open the log file C:\Temp_000001.blg for log BillTest and will be stopped. Check the log folder for existence, spelling, permissions, and ensure that no other logs or applications are writing to this log file. You can reenter the log file name using the configuration program. This log will not be started. The error returned is: Access is denied. I verified that C:\Temp exists. I'm not a permissions guru, but I did set all the accounts in the security tab of that folder to "full control." Still, the logman start command failed with the same error. I noticed that it was trying to write to C:\Temp_000001.blg instead of C:\Temp\000001.blg. That might be part of the problem. So, I tried to update my counter to "C:\Temp\" instead of "C:\Temp", but that failed with a path-invalid error. Also, all the examples I saw online used did not put a trailing slash. So, no dice there. I tried this on my machine (Windows XP) and my dev server (Windows Server 2003). Both failed with the same error. How can I fix this?

  Read the article

• Resolving a BSOD/CPU/GPU issue...

  - by Christian Sciberras

  Hello all, I'm getting a BSOD / system crash (sometimes the PC just quits without a BSOD). Hardware Specifications cpu: i7 920 2666MHz / 8 cores (not OCed afaik) mobo: Asus P6T SE ram: 2x Corsair CM3X2G1333C9 (64bit DDR3 667MHz) gfx: ATI Radeon HD 5970 1GB (XFX HD5970 BE) os: Windows 7 Ultimate 64 bit (legit) All bios, firmware and drivers are all up to date (as of today). Symptoms Sometimes the PC runs smoothly, sometimes I get this BSOD. The BSOD always happens when I'm doing something related to graphics, such as viewing a video or playing a game. I get to know about the imminent BSOD ~10 seconds earlier; the PC starts freezing occasionally but increasing in frequency and length of lag (I noticed processor usage in creased from Process Monitor). I've tweaked BIOS settings occasionally but afaik, it was in vain. A day or so ago, I reset it to factory settings. BSOD contents The computer has rebooted from a bugcheck. The bugcheck was: 0x00000101 (0x0000000000000019, 0x0000000000000000, 0xfffff88001f35180, 0x0000000000000004). 15-12-2010 A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Internal Timer Error Processor ID: 4 23-12-2010 A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Internal Timer Error Processor ID: 2 Important The interesting thing is that although the event log (and BSOD screen) blame a "secondary processor", Windows Action Center sometimes blamed the GFX driver (for the same error). Also It is interesting to note that after hibernating my PC, I always get the BSOD.

  Read the article

• Routing data through VPN in linux

  - by Shadyabhi

  I think its a silly question but still here it goes.. Terminal Output: eth0 Link encap:Ethernet HWaddr 00:1c:c0:37:5e:25 inet addr:10.100.98.51 Bcast:10.100.98.255 Mask:255.255.255.0 inet6 addr: fe80::21c:c0ff:fe37:5e25/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:29677 errors:0 dropped:0 overruns:0 frame:0 TX packets:5209 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:3179007 (3.1 MB) TX bytes:610142 (610.1 KB) Memory:e0380000-e03a0000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:76 errors:0 dropped:0 overruns:0 frame:0 TX packets:76 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:9555 (9.5 KB) TX bytes:9555 (9.5 KB) vpn_0 Link encap:Ethernet HWaddr 00:ac:39:95:a1:16 inet6 addr: fe80::2ac:39ff:fe95:a116/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1786 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:128597 (128.5 KB) TX bytes:468 (468.0 B) Actually, I followed this tutorial to setup the PacketiX VPN on ubuntu. Now, how do I actually use this VPN? Terminal Output: shadyabhi@shadyabhi-desktop:~$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default 10.100.98.4 0.0.0.0 UG 0 0 0 eth0 shadyabhi@shadyabhi-desktop:~$ As told in tutorial, if I do route del default route add default dev vpn_0 I am not able to surf the internet. And I get the route command output as: root@shadyabhi-desktop:/home/shadyabhi# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default * 0.0.0.0 U 0 0 0 vpn_0 root@shadyabhi-desktop:/home/shadyabhi# I know I am not able to route the traffic properly. How do i do that?

  Read the article

• Gray Progress Bar in Macbook Boot caused by Partition Fault

  - by Konstantin Bodnya

  Here's my problem: When I try to load my macbook it shows the gray progress bar. It takes a while to fill the whole progress and after it macbook just shuts down. I tried to boot from recovery partition and run Disk Utility to repair it. Disk Utility showed my "Macintosh HD" in a gray color and failed to repair it. I thought all my data was lost, but then I tried the following: So I booted into ubunto from live usb and it successfully mounted my macintosh hd hfs+ partition. Parted shows me the following partitions on my disk: Disk /dev/sda: 500GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 20.5kB 210MB 210MB fat32 EFI System Partition boot 2 210MB 499GB 499GB hfs+ Macintosh HD 3 499GB 500GB 650MB hfs+ Recovery HD Seems legit except for FAT32 for EFI System Partition. Since all my data is okay and backed up what should I do to recover the system. I don't really want to reinstall all the system though I believe there's a command to make it allright in linux. Thank you everyone!

  Read the article

• Web hosting for multiple web sites providing system isolation

  - by Justin

  We have a small number of projects where we expect the client will not be maintaining the installed versions of applications we install to power the site (such as Drupal). Given that an important part of security is keeping things updated, we don't want to host these projects on our Plesk-powered dedicated servers that currently host lots of our other client's websites. Our goal is to find a host where we can deploy isolated instances (be these slices, virtual servers, grid servers, etc) for each individual (or groups of 2-3) web sites as we need them. These instances would be completely separate, so that if one web site were hacked it would not impact any other site. Typical hosting requirements: Linux Apache PHP 5 MySQL Supports Drupal Ability to setup a cron task (but we don't need SSH access) Daily backups Virtualized/cloud hosting (we want to avoid shared) Pricing per site is around $25/month OS is patched automatically Some options we have considered but won't work: MediaTemple: Two major data center-wide security incidents and recent downtime foster doubt about this host's technical ability. Slicehost: This would require us to manage the entire server, which we don't want to do. Rackspace Cloud Sites (formerly Mosso): No backup options. Do you have any recommended hosting options for given these requirements?

  Read the article

• SPDIF passthrough not working in Windows 7

  - by adriangrigore

  Hi, I'm running Windows 7 on a computer with an Audigy Platinum eX sound card connected to a surround receiver via optical cabling. Sound works fine when listening to non-surround audio sources, such as windows sounds or MP3. However, when I view a DVD in Media Center and the SPDIF passthrough kicks in, I can only hear an awful noise instead of the movie soundtrack. Also, the receiver does not show the Dolby Digital or DTS symbol, but stays at Dolby Prologic, so it seems it doesn't identify the sound encoding properly. I could switch off SPDIF passthrough and use the sound card's decoder instead, but that's not an option for me since it would create more problems with regular MP3 playback via additional Stereo Receiver which is also connected to the same sound card. I've tried both the default Audigy drivers that come with Windows 7 and the latest drivers from the Soundblaster website, but the problem remains unchanged. Also, I have ensured that the receiver's Dolby Digital decoder is not broken by successfully connecting it to my PS3 to view a Dolby Digital DVD. Besides, SPDIF passthrough was working fine in Vista before I upgraded to Windows 7. Is there anything else I could try?

  Read the article

• Increasing Java's heapspace in Tomcat startup script

  - by Ankur

  I want to increase my heap size when using Tomcat. I was told to add this line export CATALINA_OPTS=-Xms16m -Xmx256m; In to the startup.sh script - I did so (at the beginning) but got the error export: 24: -Xmx256m: bad variable name Where am I supposed to add it, am I doing something else wrong? <b>export CATALINA_OPTS=-Xms16m -Xmx256m;</b> # Better OS/400 detection: see Bugzilla 31132 os400=false darwin=false case "`uname`" in CYGWIN*) cygwin=true;; OS400*) os400=true;; Darwin*) darwin=true;; esac # resolve links - $0 may be a softlink PRG="$0" while [ -h "$PRG" ] ; do ls=`ls -ld "$PRG"` link=`expr "$ls" : '.*-> \(.*\)$'` if expr "$link" : '/.*' > /dev/null; then PRG="$link" else PRG=`dirname "$PRG"`/"$link" fi done PRGDIR=`dirname "$PRG"` EXECUTABLE=catalina.sh # Check that target executable exists if $os400; then # -x will Only work on the os400 if the files are: # 1. owned by the user # 2. owned by the PRIMARY group of the user # this will not work if the user belongs in secondary groups eval else if [ ! -x "$PRGDIR"/"$EXECUTABLE" ]; then echo "Cannot find $PRGDIR/$EXECUTABLE" echo "This file is needed to run this program" exit 1 fi fi exec "$PRGDIR"/"$EXECUTABLE" start "$@"

  Read the article

• apache 2.4 redirect within virtualhost

  - by user129545

  I have a couple http (port 80) vhosts that I want to redirect to http if an https request is made to them. Apparently some things have changed with Apache 2.4 (NameVirtualHost not used like it was in the past, etc). Apache 2.4 on centos 5.5, This is all using a single ip for all vhosts below, I don't have multiple ip's on this box, my /usr/local/apache2/conf/extra/httpd-vhosts.conf : # <VirtualHost www.dom1.com:80> ServerName www.dom1.com ServerAlias dom1.com DocumentRoot /usr/local/apache2/htdocs/dom1/wordpress </VirtualHost> <VirtualHost webmail.dom2.com:443> ServerName webmail.dom2.com DocumentRoot /usr/local/apache2/htdocs/webmail SSLEngine On SSLCertificateFile /usr/local/apache2/webmail.crt SSLCertificateKeyFile /usr/local/apache2/webmail.key </VirtualHost> # my /usr/local/apache2/conf/extra/httpd-ssl.conf, # Listen 443 SSLPassPhraseDialog builtin SSLSessionCache shmcb:/var/cache/mod_ssl/scache(512000) SSLSessionCacheTimeout 300 Mutex default SSLRandomSeed startup file:/dev/urandom 512 SSLRandomSeed connect builtin SSLCryptoDevice builtin # webmail.dom2.com works fine. Problem is I can connect to https://www.dom1.com, and it serves up the content from webmail.dom2.com. I want any https requests for www.dom1.com on port 443 to simply redirect to http://www.dom1.com on port 80. Thanks

  Read the article

• Custom flash uploader breaks only on Media Temple

  - by LaserWolf

  I've built a flash uploader to upload files up to 100MB using a php backend. It works wonderfully on our dev server, on a hostgator vps, and on one of our clients' servers running Debian. It will not work on our Media Temple (dv)3.5 and I don't know why. The upload will start but will choke after a few seconds with this flash error message: ioerror: [IOErrorEvent type="ioError" bubbles=false cancelable=false eventPhase=2 text="Error #2038: File I/O Error. URL: http://..._upload.php"] The problem seems to be specific to the asynchronous nature of the flash uploader because if I try a straight php upload it works fine. The php.ini settings are set to allow such a large upload as well. Also, I've thoroughly googled flash, 2038, I/O error, etc but have yet to find anything that helped. Here's the weird part though: We work in Seattle. It won't work from the office. It won't work from home. But, while on the phone with MT's support, they were able to upload a file through our flash uploader just fine. I'm not sure where his office was located but I think it was Atlanta. So the problem also seems specific to physical location. Has anyone run into this sort of problem before?

  Read the article

• Java issues with Apache 2.0 Agent 2.202 for RHEL5 Linux 64bit

  - by Richard

  In trying to install Apache 2.0 Agent 2.202 for RHEL5 Linux 64bit, the dialogue appears as follows. $ ./setup Error : java is not present in path. Please enter JAVAHOME path to pick up java:/usr/lib/jvm/java-1.6.0-openjdk-1.6.0.0.x86_64/jre/ Launching installer... Attach to native process failed $ ./setup Error : java is not present in path. Please enter JAVAHOME path to pick up java:/usr/lib/jvm/java-1.6.0-openjdk-1.6.0.0.x86_64/jre/lib ./setup: line 80: [: 107:: integer expression expected ./setup: line 83: [: 107:: integer expression expected Error : Incorrect java version (1.2.2 or above is needed). Please enter JAVAHOME path to pick up java: On the server we have the following JREs and I've tried both. $ sudo rpm -qa | egrep "(openjdk|icedtea)" java-1.6.0-openjdk-1.6.0.0-1.27.1.10.8.el5_8 $ find 2>/dev/null | grep -i '/jre/' ./usr/lib/jvm/java-1.4.2-gcj-1.4.2.0/jre/bin/ ... ./usr/lib/jvm/java-1.6.0-openjdk-1.6.0.0.x86_64/jre/ Any suggestions? I know I'm overlooking something. In previous searches I've only found one other posting that comes close but it has no responses (http://forum.parallels.com/showthread.php?t=76556).

  Read the article

• Getting Windows (VMware) to load from OSX's localhost without an Internet Connection

  - by Jonah Goldstein

  I'm using MAMP to host my local sites, and VirtualHostX so that I can access sites during local development via a convenient URL like mysite.dev I'm also running Windows XP via VirtualBox, and it would be great to be able to load up any of my local sites within windows while offline as currently often working without access, on the move, unfortunately. I know that I can append my IP and a nice domain name to the host file in C:/WINDOWS/system32/drivers/etc ... and i can find my IP simply through terminal with "ifconfig" while I'm online. The problem is that when I'm not online, there's no IP. Even if there is an IP (when i have a connection), I still have grab it and update the windows hosts' file all the time, since I'm developing from a laptop and have a new IP at the drop of a dime. I found a tutorial where the author is able to get a permanent IP. He uses VMware Fusion as his VMachine, which is the only difference between his setup and mine. By running the terminal command "ifconfig vmnet1" he gets: a secret IP the virtual machine uses to talk to OSX And that doesn't change - which is awesome. I'm assuming it exists even if he's offline. His tutorial is here, http://bit.ly/U2lq It would be pretty fantabulous if I could replicate this with virtualBox. Anyone have ideas? Thanks:)

  Read the article

• SCCM 2012 Clients no longer detecting

  - by user3685428

  Here is the scenario I had a fully functioning SCCM 2012 site server with the DP, MP, SUP, Application catalog, etc. roles configured and working. There is only one server on this site. Everything was great but i was not happy with SUP, so i decided to create a separate WSUS server and configure Windows Updates through GPOs. That setup worked great as well so i went ahead and removed the SUP role from SCCM and removed the WSUS feature from my SCCM server (they were configured on the same SCCM Server). I did not notice any problems right away. A couple days later i noticed that the OSD deployments were giving errors, and after a couple hours of trying suggestions from Google, i was able to uninstall PXE and make a few changes and reinstall with WDS to get it working again. Again, thought everything was fine and continued on. The last couple days i have noticed that any new machine deployed or installing the Client will show in the SCCM console as "No" Client. The client machines will show connected to a site but the software center shows "IT Organization" instead of our site like the previous clients. The existing clients all seem to be functioning normally. they still receive application distributions and configuration baselines, etc. Reinstalling, uninstalling and reinstalling, repairing does not fix the problems and this happens on all new clients. ClientLocation.log shows it connecting to the correct MP. Nothing odd in any of the logs except for the ClientMessaging.log which repeats continuously this line: <![LOG[Raising event: instance of CCM_CcmHttp_Status { ClientID = "GUID:0450fde3-ab82-41bf-9c33-87a18113744b"; DateTime = "20140528214824.993000+000"; HostName = "SOUNDWAVE.domain.org"; HRESULT = "0x00000000"; ProcessID = 4092; StatusCode = 0; ThreadID = 3720; }; ]LOG]!><time="16:48:24.994+300" date="05-28-2014" component="CcmMessaging" context="" type="1" thread="3720" file="event.cpp:706"> thanks

  Read the article

< Previous Page | 436 437 438 439 440 441 442 443 444 445 446 447  | Next Page >