Search Results

Search found 11938 results on 478 pages for 'secure boot'.

Page 440/478 | < Previous Page | 436 437 438 439 440 441 442 443 444 445 446 447  | Next Page >

• Display issue with fresh install of windows server 2012

  - by Tony

  I installed windows server 2012 last night on my home "server". I use server loosely. From the get go I had display and graphic issues. The image was fuzzy and jumbled up during the install. This continued once booted into the install. I did installed Server 2012 twice now as the first time, I only installed "core". I know this is not a busted graphics card because it worked fine in Win7, during boot, and fine in "core" mode. Once booted into "GUI" install of Server 2012, the image was messed up again. To make things even more weird, the windows "loading" screen looks fine. Once the login screen appears the image is fuzzy and jumbled. My guess was that it was a driver issue. I did try to install the win8 x64 drivers from nvidia. This caused the system to become unbootable and I had to restore to a previous working point and uninstall the driver. I did try two different monitors and cables. Also both ports on the back of the video card. I did manage to get RDP running and that works fine. I rarely work directly on this machine but it would be nice to have the option back. Geforce 210, AMD 4600+, 4 gigs of ram.

  Read the article

• Computer hangs at BIOS screen. Cannot enter setup.

  - by d2jxp

  I have an HP Pavilion a6500f (it's a year out of warranty) and it's hanging on the blue HP BIOS screen. If I mash F10 while it's starting up, it will say "Entering Setup..." but I will see no results. It will hang there and not do anything. If I actually wait until I can see the screen and then hit F10, there's no response at all and the computer will sit at the BIOS menu. I've dusted and cleaned it out, reseated the memory, switched the RAM slots, and reset the CMOS battery using the reset jumper. I'm out of ideas. I'm pretty sure it's not a hard drive issue, since my problem is at the BIOS. After this post, I'll disconnect the hard drive and try to just boot without it. Anyone have any other ideas? Edit: Okay, so I tried disconnecting the hard drive and now I can get back into the BIOS. I reconnected it and I'm locked out again. So the problem is my hard drive.. I guess I should delete this post unless someone has any ideas as to what's wrong with the drive?

  Read the article

• K8NDRE motherboard in server fails to complete BIOS load with error 0078

  - by John

  K8NDRE motherboard with 4 sata drives, was running fine. Drives had raid-0 and raid-1 partitions, using mdadm. The onboard raid is disabled. Upon reformatting the drives, setting a new partition structure and new raid partitions, the bios fails to finish loading, with 0078 in the bottom right corner. Tried using completely new set of drives, and bios worked fine. Able to boot from a usb, format the drives, partition them, start raid, and then installed os. Reboot and received the same error from the bios, 0078. Works fine if I unplug the sata drives. Any thoughts? Physical inspection reveals no damage cables, connectors, or capacitors. Server was running happily for over a year, and this is the first problem it has had. Per Michael Hampton's answer: The drives, unjumpered and supporting sata III worked fine originally, and worked fine for formatting and having new partitions and raid installed on them. I did try jumpering one, with no change. If I put a brand new unformatted drive in, the motherboard recognizes it and I can proceed with formatting and installing. When I reboot, I get the 0078. I have 4 sata cables-the board supports 4 drives, so I tried each and no change. I am close to calling the motherboard done.

  Read the article

• Linux will not activate wireless after device has been re-enabled

  - by XHR

  Using a Eee 900A netbook by Asus. By pressing Fn + F2, I can disable or enable the wireless chip on the netbook, a blue LED indicates the status. I've been able to connect to wireless networks just fine with this netbook. However, if the wireless chip ever becomes disabled, I have to reboot to get my network connection back. This generally happens when suspending. For some reason the LED will be off and I have to hit Fn + F2 for it to light up again. However, after doing so, Linux will not reconnect to the network. It simply changes the wireless status from "wireless is disabled" to "device not ready". Even worse, I've recently had issues with the chip being enabled at boot, thus making it nearly impossible to get connected. I've searched around on-line but haven't found much of anything useful on this. This happens on all kinds of different distros including Ubuntu 9.10 Netbook, EeeBuntu 4 beta, Jolicloud and Ubuntu 10.04 Netbook. Edit I noticed this question is getting a lot of views. To give a quick update, I never did resolve this issue with the given distro's. However, I'm currently running Ubuntu 10.10 netbook edition and this issue has gone away.

  Read the article

• How do I cancel windows server 2003 repair install?

  - by Kilgore2k

  System: Windows 2003 Server Enterprise Scenario: NTDS db is corrupt and all attempts to fix with esentutl fail. Ran chkdsk which seemed to repair disk error and give access to the ntds.dit file but still esentutl fails. (Attached the drive to a different server to run the esentutl) Error: Access to source database '[path to copy of]/ntds.dit' failed with Jet error -1022. Operation terminated with error -1022 (JET_errDiskIO, Disk IO error) after 0.170 seconds. This error occurs on any disk I cpoy the files to including original location in C:\WINDOWS\NTDS\ Now enter the "Stupid!" and "what was I thinking!?" part (must be the late hour...) Stupid: No updated backup - after using a backup I get a network password error in the lsass error. what was I thinking!?: Started the install repair from the original CD but the install fails since the AD fails to start. Now I cant boot into any mode (safe mode, AD restore etc) nor complete the repair install. I would really like to avoid a fresh install since I have the Exchange server on this DC and would rather migrate to a new server than have to start from scratch. Thanks!

  Read the article

• Random keyboard malfunction - happens in Vista and XP

  - by Stupefy101

  For some weird reason, some of my keyboard keys of my deskop are acting very strangely. I don't remember a certain time when it started and I can't recognize any pattern as to when it happens and when it doesn't. The problem occurs in Windows XP, XP Safe Mode, Vista, and Vista Safe mode (I have a dual boot system) Here's what's happening: When I push the I, K, comma, or 8 keys (notice how they are all in the same column), instead of just getting that character, I get extra characters afterwards. For example, I'll push the k key and it will print "ksfda", pushing "I" gives me "IWREQ", comma gives me ", xvcz", pushing 8 gives me "82431". There are a couple things that I have noticed: It does not happen every time I push the key It happens in all OS and applications I have tested The characters coming after the desired ones are in the same pattern (column order: 2, 4, 3, 1 from the left of the keyboard in the same row as the key pressed. Pressing "]" will sometimes give me "]t", and if done in Notepad, will bring up the "Find" dialog window I cannot seem to remember a specific time the problem started, although I have been defragging, using TuneUp Utilities + CCleaner, and installing lots of new programs lately.

  Read the article

• SBS DC DNS entries going missing?

  - by Chris W

  I've been looking at a problem on a friends SBS (2003) server where the client PC's aren't able to connect to the server with a variety of errors reported. Checking the server itself the only indicator of an issue is an error 5782: Dynamic registration or deregistration of one or more DNS records failed with the following error: No DNS servers configured for the local system. Running a dcdiag reports that there are no DNS records registered for the DC so I fixed the problem by doing a netdiag /fix after which the dcdiag comes back clean and clients are ok again. It happened a few weeks ago as well and the same fix solved it. What are the possible causes of the DC DNS entries going missing? Is this a config option that needs tweaking or could it be solved by something simple like scheduling the SBS server to re-boot periodically? The only change they can think of that was made near to the time of the first instance of this problem occurring is that RRAS was started up to allow for a VPN connection from a home user. NB - The server is setup with a pair of NICs in a team so the server has a single virtual NIC providing both LAN/WAN connections to it. An external hardware firewall is in use rather than the windows firewall.

  Read the article

• Backup data from RAID 1 disk out of its server

  - by Doomsday

  I'm facing with a pretty easy problem in my opinion. I've extracted a working disk from a RAID1 and I'm looking to copy only data (FS and RAID configuration doesn't matter) into another location (another FS). My problem is I'm not able to mount properly this disk into another linux. I've first looked the partition table : # fdisk -l /dev/sdc Disk /dev/sdc: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders, total 1250263728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 63 1249535699 624767818+ fd Linux raid autodetect /dev/sdc2 1249535700 1250017649 240975 fd Linux raid autodetect /dev/sdc3 1250017650 1250258624 120487+ 82 Linux swap / Solaris I've understood I should use dmraid tools. Once installed : # cat /proc/mdstat Personalities : md0 : inactive sdc1[1](S) 624767744 blocks unused devices: <none> And some other informations : # mdadm --examine /dev/sdc1 /dev/sdc1: Magic : a92b4efc Version : 0.90.00 UUID : 8f292f54:7e5aef72:7e5ab5fd:b348fd05 Creation Time : Mon Jun 2 03:39:41 2008 Raid Level : raid1 Used Dev Size : 624767744 (595.82 GiB 639.76 GB) Array Size : 624767744 (595.82 GiB 639.76 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Update Time : Tue Feb 7 22:34:59 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Checksum : a505b324 - correct Events : 15148 Number Major Minor RaidDevice State this 1 8 1 1 active sync /dev/sda1 0 0 8 17 0 active sync /dev/sdb1 1 1 8 1 1 active sync /dev/sda1 From here, I've tried to mount but I'm not comfortable with dmtools and how it's working. # mount /dev/sdc1 /mnt/sdc1 mount: unknown filesystem type 'linux_raid_member' # mount /dev/md0 /mnt/sdc1 mount: /dev/md0: can't read superblock I've seen some options to alter RAID array with mdadm but I only want to copy data on its filesystem before wiping them... Anyone has a clue ?

  Read the article

• How is network mounted software executed?

  - by CptSupermrkt

  I would like to understand how network mounted software works. For example, at my place of work, we have a software server. Each client machine (hundreds of them) automatically mounts directories from the software server on boot. For example, a program like Matlab is installed just once on the software server, but each client machine can start up an instance of Matlab. What is going on under the hood? Let's say I run /opt/bin/matlab and /opt/ is mounted from the software server, what happens when I press Enter to execute matlab on a client machine? The process is on the client machine, and I've already narrowed down that there isn't any implicit or hidden file transfer (i.e. copying matlab to my machine temporarily for that session) by running matlab on a computer with nearly zero disk space (i.e. not enough room to transfer). Since Matlab was installed on the server, how is my client computer executing it? What mechanism is controlling this? What is happening behind the scenes?

  Read the article

• Primary/secondary ethernet interfaces in Ubuntu 9.10

  - by Josh

  I have an Ubuntu 9.10 machine with three ethernet interfaces, eth0, eth1 and eth2. eth2 is connected to a private network. eth0 and eth2 are connected to two different LANs. Either one will provide access to the internet. All three networks have DHCP servers. Using Ubuntu's the default settings (And Gnome), when I boot up all the interfaces are active and my system gets three IP addresses. However any attempt to access the internet results in connection timeouts and other weirdness. I suspect that traffic is going out on one NIC (like eth0) and coming back in on another (like eth1). I'm not sure what's going on. The only way I can access the internet at the moment is to bring two of the devices down with ifdown. How can I configure eth0 as my primary interface so all trafic goes out by default on that interface, while keeping the other two active? Also, I want to make sure Avahi broadcasts properly on all three IPs so that the computers on the LAN of eth1 can still connect to myHostname.local...

  Read the article

• Notebook display problem (multiplication)

  - by SubniC

  Hi, I'm having some troubles with the display of a LG E500 notebook. The thing is that without any known reason the display starts to show the screen divided in eigth parts and each part show the display image as if I had a matrix of eigth displays :) I thought it could be some kind of refresh rate problem or driver related, but it is happening at boot-up as well and the BIOS. I got the computer completely unassambled yesterday and I check all the wires and connectors looking for something broken or unconected, but without luck... You can see a picture here of the problem (sorry for the low quality, but I think it illustrate the problem. EDIT 1: I uploaded a new pictrue, here you cans ee the problem better :) There are three horizontal lines that you can see just between the windows. You can see the grey line at the first moment you turn on the computer and the after the duplicated screens show up just like if they where arranged over a grid (over the horizontal lines...) I hope it makes any sense. Do you know what could be happening? or can you tell me what would you do? Thank you very much for your help.

  Read the article

• My home router randomly disconnects me and I'm unable to reconnect to it

  - by Roy Tang

  It's happened a few times, I'm not sure how to diagnose/debug, so any advise would be appreciated. Symptons: sometimes the router will randomly disconnect; the connection icon on my desktop (wired to the router) gets that yellow "!" symbol that tells me my connection just went down. At this point I'm unable to ping the router. afterwards I try to reset the router by removing then reconnecting the power jack on the router side (this is the fastest way as I can't reset the power strip it's connected to without rebooting my desktop. the router has a reset thingy, but it's one of those things where i have to find a pin to stick into the hole, and when I get disconnected I usually need to get reconnected immediately so I just pull and put back the power jack), but even after that the connection has the same state. after the router reboots, if I try to connect to it using a wifi device like my ipad, the ipad prompts me for the wifi password even though it had already "remembered" all the settings for this router forever after i finally decide to reboot the power strip, and my desktop and the router boot up again, the connection returns to its normal state somewhat and i'm able to connect to it as normal using the desktop and wifi devices. What do I need to check the next time this happens so I can figure out the problem? Is it possibly because we've been using the power jack on the router as an easier way to reboot it? Should I be shopping around for a new router? If it helps, the router is a DLink DIR-300

  Read the article

• Windows drive letters A: and B:

  - by Workshop Alex

  This is a question that just popped into my mind and I can't help but wonder why it's still common for a Windows installation to be installed on C: with all other drive letters going up from D: to Z:. In the early MS-DOS times, all we had were floppy disks and they were at A:. When the 3.5 inch floppy started to replace the 5.25 floppy, many people had an A: and B: drive. Then the hard disk became popular and the hard disk was at C: because A: and B: were taken. Then the 5.25 floppy disappeared and most computers had a gap between A: and C:. Nowadays, the 3.5 floppy is just too outdated so A: disappeared too. All disks now start at C:. Yeah, I know I can assign my own drive letters and I've done so with my data disks. My installation disk will just continue to be stuck at C: and I don't really mind. I have no problems with drive letters. But why do the new Windows versions just continue to install themselves by default on C: instead of assigning the letter A: to the boot hard disk?

  Read the article

• How to verify TRIM/discard on encrypted swap?

  - by svarni

  I am using an encrypted swap partition via ecryptfs-setup-swap on my Ubuntu 13.04 computer using a SSD. I have manually set up trim for my ext4 root partition (simply by adding the "discard" option in /etc/fstab). I also manually ran fstrim on the root partition prior to booting and using dstat I saw that for a few seconds several GB/s of data have been written to the disk. That was presumably the effect of the trim command. These high writerates are reproducable by deleting huge files and have not occured before setting up trim, so I take them as evidence for working trim/discard. Manually enabling trim on my root partition has stopped the wearout of my precious new disk from 365 used reserved blocks (out of 6176 total) within three months down to 0 additional used reserved blocks within three additional months (data from SMART attributes). Because I want to minimize the wearout of my SSD I now would like to know whether my swap partition (which is encrypted using ecryptfs-setup-swap) also makes use of the trim/discard option. I tried sudo swapon -d -v /dev/mapper/cryptswap1 but did not receive particular information ("-v") about whether trim/discard ("-d") was applied. If unsupported, i would expect a message. Then I tried sudo dd if=/dev/sda6 count=1 BS=1M | xxd | less directly after booting and when no swapspace was used but I saw not only zeroes. I assume, when looking at freshly trimmed regions, the disk would send zeroes instead of reading random sectors (and according to some forums, (unencrypted) swap space is trimmed once upon boot). Long story short: Are there any ideas on how to test if trim is effectively used for my encrypted swap? And if not, any ideas on how to - at least manually, for once - trim the whole swap space? I wouldn't want to tinker with the partition itself, because I dont know if it needs to be reinitialized as (encrypted) swap - I dont want to be left with an unbootable system :)

  Read the article

• Extending partition on linux gparted but not more space in the vm

  - by Asken

  I have a vm test installation of a linux running a build server. Unfortunately I just pressed ok when adding the disk and ended up with an 8gb drive to play with. Well into the test the builds are consuming more and more space, of course. The vm drive was resized to 21gb and using gparted I expanded the drive partitions and that all worked fine but when I go back into the console and do df there's still only 8gb available. How can I claim the other 13gb I added? fdisk -l Disk /dev/sda: 21.0 GB, 20971520000 bytes 255 heads, 63 sectors/track, 2549 cylinders, total 40960000 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0006d284 Device Boot Start End Blocks Id System /dev/sda1 * 2048 499711 248832 83 Linux /dev/sda2 501758 40959999 20229121 5 Extended /dev/sda5 501760 40959999 20229120 8e Linux LVM vgdisplay --- Volume group --- VG Name ct System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 2 Open LV 2 Max PV 0 Cur PV 1 Act PV 1 VG Size 19.29 GiB PE Size 4.00 MiB Total PE 4938 Alloc PE / Size 1977 / 7.72 GiB Free PE / Size 2961 / 11.57 GiB VG UUID MwiMAz-52e1-iGVf-eL4f-P5lq-FvRA-L73Sl3 lvdisplay --- Logical volume --- LV Name /dev/ct/root VG Name ct LV UUID Rfk9fh-kqdM-q7t5-ml6i-EjE8-nMtU-usBF0m LV Write Access read/write LV Status available # open 1 LV Size 5.73 GiB Current LE 1466 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 252:0 --- Logical volume --- LV Name /dev/ct/swap_1 VG Name ct LV UUID BLFaa6-1f5T-4MM0-5goV-1aur-nzl9-sNLXIs LV Write Access read/write LV Status available # open 2 LV Size 2.00 GiB Current LE 511 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 252:1

  Read the article

• External Dell Display doesn't work with MacBook Pro (2011) after Thunderbolt Firmware Update (1.0 and 1.2)

  - by tom

  Today two Thunderbolt Firmware Updates (1.0 and 1.2) became available for my MacBook Pro (Early 2011). After installing both, my external monitor, a Dell U2713HM, does no longer work. The system detects the display, but the display shows only black. An Apple Thunderbolt display works fine and a MacBook Air can use the Dell monitor without problems. My MacBook Pro can use the Dell monitor just fine when I boot from a USB stick. Therefore, clearly the Thunderbolt Firmware Update seems to be the problem. Does anyone have the same problem? Any solutions or workarounds? I guess there is no way to remove a Thunderbolt Firmware Update once it's installed, right? Update 24.10.2013: Is there no one else with this problem? In the meantime I tried three different cables – none worked. My colleague with the same generation MacBook Pro also can't use my display after installing the firmware update. All colleagues with MacBook Airs and newer MacBook Pros (all didn't receive the firmware update) can use the display. Update 29.10.2013: Wow, ok today my new MacBook Pro Retina 13' (Late 2013) arrived. Guess what, I cannot use the display with it. Only HDMI works – not with the full resolution.

  Read the article

• In Windows 7 power management, is it possible to set different sleep settings for different SATA disks?

  - by Ben Voigt

  I'm having an issue with Windows 7 either freezing up or generating a BSOD coming out of sleep. I suspect that it is related to my boot/OS drive, an OCZ Vertex SE SSD, because numerous other Vertex users have reported sleep problems. Notably, if I put the computer to sleep, it almost always wakes correctly. If it goes to sleep after a timeout, it almost always BSODs. I disabled timed sleep and now it freezes when left unattended. My next step is to disable "Put hard disks to sleep after X minutes", but I'd like to change this setting only for the SSD and not for the rotating data disks, which I would like to spin down normally. Does anyone know a place to configure sleep on a per-disk basis? I don't need to set different timeouts on different disks (although that would be nice), simply setting "this disk sleeps" and "sleep is disabled for this disk" would be great. Additional system information: Windows 7 Ultimate x64, Core i5 - P55 chipset, Intel RST drivers are installed. One SSD, two rotating HDD, and a DVD-RW drive are all connected to the Intel SATA ports. I could potentially move some of these to my motherboard's other SATA controller if that would help.

  Read the article

• How to disable monitor "sleep" on Ubuntu without access to X?

  - by exhuma

  I just received a CuBox (basically a tiny ARM based PC). It comes pre-installed with Ubuntu, and I did not (yet) want to fiddle with the OS itself. My aim is to have it automaticall start a browser in fullscrren upon boot. Using chromium with the "--kiosk" flag works perfectly in that regard. But now I have the problem that the screen turns off after a certain time. I managed to turn off the screen saver using: gconftool-2 -s /apps/gnome-screensaver/idle_activation_enabled --type=bool false And tried to turn off the power management using: gconftool-2 -s /apps/gnome-power-manager/ac_sleep_display --type=int 0 and gconftool-2 -s /apps/gnome-power-manager/timeout/sleep_display_ac --type=int 0 Neither of the power-management commands worked. Theoretically I could hook up a mouse and keyboard and configure it manually. But I want to learn how to do it over the console. The box will eventually be only reachable via SSH. So I'd like to be able to trouble-shoot it later. I don't quite know where to look for. I searched the gconf tree using gconftool-2 -S for anything related to the terms power, idle and sleep but did not find anything promising. Maybe it's not even gconf related... Any ideas what else I could look for?

  Read the article

• Decrease in disk performance after partitioning and encryption, is this much of a drop normal?

  - by Biohazard

  I have a server that I only have remote access to. Earlier in the week I repartitioned the 2 disk raid as follows: Filesystem Size Used Avail Use% Mounted on /dev/mapper/sda1_crypt 363G 1.8G 343G 1% / tmpfs 2.0G 0 2.0G 0% /lib/init/rw udev 2.0G 140K 2.0G 1% /dev tmpfs 2.0G 0 2.0G 0% /dev/shm /dev/sda5 461M 26M 412M 6% /boot /dev/sda7 179G 8.6G 162G 6% /data The raid consists of 2 x 300gb SAS 15k disks. Prior to the changes I made, it was being used as a single unencrypted root parition and hdparm -t /dev/sda was giving readings around 240mb/s, which I still get if I do it now: /dev/sda: Timing buffered disk reads: 730 MB in 3.00 seconds = 243.06 MB/sec Since the repartition and encryption, I get the following on the separate partitions: Unencrypted /dev/sda7: /dev/sda7: Timing buffered disk reads: 540 MB in 3.00 seconds = 179.78 MB/sec Unencrypted /dev/sda5: /dev/sda5: Timing buffered disk reads: 476 MB in 2.55 seconds = 186.86 MB/sec Encrypted /dev/mapper/sda1_crypt: /dev/mapper/sda1_crypt: Timing buffered disk reads: 150 MB in 3.03 seconds = 49.54 MB/sec I expected a drop in performance on the encrypted partition, but not that much, but I didn't expect I would get a drop in performance on the other partitions at all. The other hardware in the server is: 2 x Quad Core Intel(R) Xeon(R) CPU E5405 @ 2.00GHz and 4gb RAM $ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 32 Lun: 00 Vendor: DP Model: BACKPLANE Rev: 1.05 Type: Enclosure ANSI SCSI revision: 05 Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC 6/i Rev: 1.11 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: CD-ROM GCR-8240N Rev: 1.10 Type: CD-ROM ANSI SCSI revision: 05 I'm guessing this means the server has a PERC 6/i RAID controller? The encryption was done with default settings during debian 6 installation. I can't recall the exact specifics and am not sure how I go about finding them? Thanks

  Read the article

• What user information is exposed via a browser?

  - by ipso

  Is there a function or website that can collect and display ALL of the user information that can be obtained via a browser? Background: This of course does not account for the significant cross-reference abilities of large corporations to collate multiple sources and signals from users across various properties, but it's a first step. Ghostery is just a great idea; to show people all of the surreptitious scripts that run on any given website. But what information is available – what is the total set of values stored – that those scripts can collect from? If you login to a search engine and stay logged in but leave their tab, is that company still collecting your webpage viewing and activity from other tabs? Can past or future inputs to pages be captured – say comments on another website? What types of activities are stored as variables in the browser app that can be collected? This is surely a highly complex question, given to countless user scenarios – but my whole point is to be able to cut through all that – and just show the total set of data available at any given point in time. Then you can A/B test and see what is available with in a fresh session with one tab open vs. the same webpage but with 12 tabs open, and a full day of history to boot. (Latest Firefox & Chrome – on Win7, Win8 or Mint13 – although I'd like to think that won't make too much of a difference. Make assumptions. Simple is better.)

  Read the article

• System x3550 M2 stuck on system initializing after firmware upgrades

  - by itmanager223

  Hey guys so i have been having this major issue for the last few hours now. I have a system x 3550M2 server and i ran the UEFI and IMM firmware upgrades within windows server 2008 R2 x64. All upgrades went fine and i was told to reboot. I performed the reboot cleanly using the OS restart option. Upon restarting it showed the system initializing screen and it stayed there for a good hour. After that hour i figured it froze and so i powered down and power up again. Now i can not boot back up to even see the IBM splash screen or the OS... I have tried switching the Jumpers to go to the backup UEFI and backup IMM and no luck. I have also reset the CMOS power and i have pressed the reset button 3 times on the light path and no luck. There are no lights light on the light path to indicate anything is broken. The only thing i see on the light path is the number 0.5. Any ideas guys i am quite stumped with this problem. Thanks a lot, Dani Cela

  Read the article

• Migrating from one linux install to another: How to keep the second disk around?

  - by Jim Miller

  I've got a linux box running Fedora 19 that I want to move to CentOS 6.4. Rather than trying to do something fancy with the current disk (which has also accumulated a lot of sludge over the years), I'm going to get a new disk, put CentOS on that, and then move the to-be-preserved bits of stuff from the old disk to the new one. I haven't done this yet, but I presume it should be semi-straightforward -- do the CentOS install on the new disk, mount the old disk on /olddisk or somesuch, and start copying. However, I'm not sure how to handle getting the machine to recognize the new empty disk as the target of the CentOS install (I suppose I can just pull the old disk during the installation), remember that this is the intended boot disk once the install has happened), and tweak /etc/fstab (right?) to set up the old disk on the desired mount point. (Both disks are, or will be, SATA.) I could probably hack it together without losing too much hair or doing too much damage, but could anyone offer some advice that would get/keep me on the right track? Thanks!

  Read the article

• Proper approach to debug PC startup problems (POST)

  - by saurabhj

  My CPU was heating up to around 65 deg C and last time this had happened (about a year ago), I got thermal paste put between the CPU and heat sink and this managed to get it down to about 45 - 50 degrees. This time, I got some thermal paste and put it myself. However, my PC is not showing the POST display and not starting up. This is what happens LEDs light up HDDs spin Mouse is getting power All fans including the processor fan starts No display on monitor No diagnostic beep sounds (no sounds at all) What I have tried Removing everything including RAM, HDD, PCI cards, AGP card Boot up machine No changes from first state. What steps can I take to figure out where the problem lies? Note (might be important) When I removed the heat sink, the processor came out with it (it was stuck to it inspite of the processor latch on) Had to pry it separate with a screw-driver. Configuration Pentium 4, 2.8 Ghz with HT (very old, I know) Original Intel Mobo with onboard sound and graphics (GB series) 2x512 Mb DDR-RAM 2 SATA disks (320 Gigs / 250 gigs) DVD Writer Creative Sound Card Network card Any help would be appreciated. Thanks!

  Read the article

• Deploying multiple identical copies of a virtual machine for compute tasks

  - by Reid

  I have a compute task which has a large number of library dependencies. I would like to deploy it on some of my company's large Linux clusters, where I do not have root. I could probably track down, compile, and install the right versions of all the libraries, but this looks to be quite tedious and would have to be repeated if I deployed it again somewhere else. On the other hand, it's pretty easy to install on current Ubuntu. This led me to wonder about a virtual machine approach. Could I put together a virtual machine which booted up, ran the computation (with parameters from and results to the host), and then shut down? In other words, I'd like a command like this that I could run on the host: $ ./run-vm --ram N --task /path/on/host/foo.sh --results /another/host/dir/ This would boot the VM, run foo.sh, and put the (relatively small) results of the computation in /another/host/dir/. It's important to start up many instances of the VM simultaneously, both on a single node and multiple nodes of the cluster. So it would be nice if I didn't have to make many copies of the VM virtual disk and metadata. As the task instances are completely independent, the VMs would not need any network support once deployed, or any outside communications beyond reading and writing the host filesystem. Is this possible, and if so, how might I go about doing it? Are there assumptions I've made above which are bogus?

  Read the article

• Windows 7 Taskbar resets on every login

  - by Arne Mertz

  I like to reorder my Taskbar a bit, other than the Windows 7 default is. I use two "rows", the lower is for quicklaunch and other toolbars: This works perfectly, as long as I don't log off from the computer. Every time I log in, Windows 7 has messed up/reset the toolbar positions like this: So I have to drag them into position again and again, every morning. Fixing the taskbar positions won't help, I tried to google for the problem but it does not seem to be very common. Does anyone recognize that problem and has a solution? Update: This is not the AutoLogon bug. AutoLogon is off. We have installed Novell at our company, and it does not matter wether I log directly onto the Novell network or only to the computer first and to Novell later. Update2: I get the same issue when I logon without Novell, i.e. when I log on only to the computer. When I boot in safe mode, the taskbar looks essentially the same: Update3: KB979155 says it's "not applicable to my system". Creating a neew user is not an option since I don't have the admin privileges to do that - I have almost any other local admin privileges, though.

  Read the article

< Previous Page | 436 437 438 439 440 441 442 443 444 445 446 447  | Next Page >