Search Results

Search found 21171 results on 847 pages for 'cdo message'.

Page 441/847 | < Previous Page | 437 438 439 440 441 442 443 444 445 446 447 448  | Next Page >

• Cisco ASA - Enable communication between same security level

  - by Conor

  I have recently inherited a network with a Cisco ASA (running version 8.2). I am trying to configure it to allow communication between two interfaces configured with the same security level (DMZ-DMZ) "same-security-traffic permit inter-interface" has been set, but hosts are unable to communicate between the interfaces. I am assuming that some NAT settings are causing my issue. Below is my running config: ASA Version 8.2(3) ! hostname asa enable password XXXXXXXX encrypted passwd XXXXXXXX encrypted names ! interface Ethernet0/0 switchport access vlan 400 ! interface Ethernet0/1 switchport access vlan 400 ! interface Ethernet0/2 switchport access vlan 420 ! interface Ethernet0/3 switchport access vlan 420 ! interface Ethernet0/4 switchport access vlan 450 ! interface Ethernet0/5 switchport access vlan 450 ! interface Ethernet0/6 switchport access vlan 500 ! interface Ethernet0/7 switchport access vlan 500 ! interface Vlan400 nameif outside security-level 0 ip address XX.XX.XX.10 255.255.255.248 ! interface Vlan420 nameif public security-level 20 ip address 192.168.20.1 255.255.255.0 ! interface Vlan450 nameif dmz security-level 50 ip address 192.168.10.1 255.255.255.0 ! interface Vlan500 nameif inside security-level 100 ip address 192.168.0.1 255.255.255.0 ! ftp mode passive clock timezone JST 9 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network DM_INLINE_NETWORK_1 network-object host XX.XX.XX.11 network-object host XX.XX.XX.13 object-group service ssh_2220 tcp port-object eq 2220 object-group service ssh_2251 tcp port-object eq 2251 object-group service ssh_2229 tcp port-object eq 2229 object-group service ssh_2210 tcp port-object eq 2210 object-group service DM_INLINE_TCP_1 tcp group-object ssh_2210 group-object ssh_2220 object-group service zabbix tcp port-object range 10050 10051 object-group service DM_INLINE_TCP_2 tcp port-object eq www group-object zabbix object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service http_8029 tcp port-object eq 8029 object-group network DM_INLINE_NETWORK_2 network-object host 192.168.20.10 network-object host 192.168.20.30 network-object host 192.168.20.60 object-group service imaps_993 tcp description Secure IMAP port-object eq 993 object-group service public_wifi_group description Service allowed on the Public Wifi Group. Allows Web and Email. service-object tcp-udp eq domain service-object tcp-udp eq www service-object tcp eq https service-object tcp-udp eq 993 service-object tcp eq imap4 service-object tcp eq 587 service-object tcp eq pop3 service-object tcp eq smtp access-list outside_access_in remark http traffic from outside access-list outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq www access-list outside_access_in remark ssh from outside to web1 access-list outside_access_in extended permit tcp any host XX.XX.XX.11 object-group ssh_2251 access-list outside_access_in remark ssh from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group ssh_2229 access-list outside_access_in remark http from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group http_8029 access-list outside_access_in remark ssh from outside to internal hosts access-list outside_access_in extended permit tcp any host XX.XX.XX.13 object-group DM_INLINE_TCP_1 access-list outside_access_in remark dns service to internal host access-list outside_access_in extended permit object-group TCPUDP any host XX.XX.XX.13 eq domain access-list dmz_access_in extended permit ip 192.168.10.0 255.255.255.0 any access-list dmz_access_in extended permit tcp any host 192.168.10.29 object-group DM_INLINE_TCP_2 access-list public_access_in remark Web access to DMZ websites access-list public_access_in extended permit object-group TCPUDP any object-group DM_INLINE_NETWORK_2 eq www access-list public_access_in remark General web access. (HTTP, DNS & ICMP and Email) access-list public_access_in extended permit object-group public_wifi_group any any pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu public 1500 mtu dmz 1500 mtu inside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 60 global (outside) 1 interface global (dmz) 2 interface nat (public) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 2229 192.168.0.29 2229 netmask 255.255.255.255 static (inside,outside) tcp interface 8029 192.168.0.29 www netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.13 192.168.10.10 netmask 255.255.255.255 dns static (dmz,outside) XX.XX.XX.11 192.168.10.30 netmask 255.255.255.255 dns static (dmz,inside) 192.168.0.29 192.168.10.29 netmask 255.255.255.255 static (dmz,public) 192.168.20.30 192.168.10.30 netmask 255.255.255.255 dns static (dmz,public) 192.168.20.10 192.168.10.10 netmask 255.255.255.255 dns static (inside,dmz) 192.168.10.0 192.168.0.0 netmask 255.255.255.0 dns access-group outside_access_in in interface outside access-group public_access_in in interface public access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.9 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 20 console timeout 0 dhcpd dns 61.122.112.97 61.122.112.1 dhcpd auto_config outside ! dhcpd address 192.168.20.200-192.168.20.254 public dhcpd enable public ! dhcpd address 192.168.0.200-192.168.0.254 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics host threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 130.54.208.201 source public webvpn ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp !

  Read the article

• IIS7 Windows Server 2008 FTP -> Response: 530 User cannot log in

  - by RSolberg

  I just launched my first IIS FTP site following many of the tutorials from IIS.NET... I'm using IIS Users and Permissions rather than anonymous and/or basic. This is what I'm seeing while trying to establish the connection... Status: Resolving address of ftp.mydomain.com Status: Connecting to ###.###.##.###:21... Status: Connection established, waiting for welcome message... Response: 220 Microsoft FTP Service Command: USER MyFTPUser Response: 331 Password required for MyFTPUser. Command: PASS ******************** Response: 530 User cannot log in. Error: Critical error Error: Could not connect to server

  Read the article

• Windows 7 boot manager issue

  - by L.ppt

  I was having windows 7 installed on my laptop, yesterday I tried to install Open Suse operating system. During its installation I chose a NTFS partition and formatted it to ext4 filesystem. During installation an error came that mount point cannot be created on this partition and I aborted the installation. They on reboot a message came BootMgr is missing. I then reinstalled the windows but on complete installation when setup rebooted the system then a blank screen came with a cursor blinking. I went through many forums and learnt may startup repairs and commands but it continues to hang up at a blank screen with cursor blinking. Reinstalling new windows 7 is also not doing any effect. I urgently need to repair my laptop for very important work. Please Help

  Read the article

• supervise apache with daemontools

  - by perlwle

  I am trying to setup daemontools for two apaches in one server. one apache 2.2 listening on port 80 proxy request to a second apache 1.3 listening on port 8888. ./run script as following: #!/bin/sh # apache 1.3 exec /apache_1_3/apache/bin/httpd -F #!/bin/sh # apache 2.2 exec /apache_2_2/apache/bin/httpd -D FOREGROUND daemontools monitors both apache fine. however, If I stop apache2.2 (using svc -t or apachectl), the apache 1.3 will see the following error in error_log [crit] (98)Address already in use: make_sock: could not bind to port 8888 I had to manually apachectl stop the apache1.3 to stop the error message clobber the log file. There is no such problem before using daemontools. any idea why this is happening?

  Read the article

• How do I make an exe into a service on Windows?

  - by user3677994

  I recently made an application that has multiple parts. One of the parts is a networking tool - it always starts with the OS, and it never displays any sort of message. It does, however, start an incredibly irritating console, which is impossible to get rid of without closing the program itself (please just accept this one as given). I have decided to work around this problem by starting the program (it's a *.exe) as a service, thus stopping it from showing up at all. As the application will be distributed to various computers (hence the need for a networking tool in the first place). I need a way to make this program install as a service (so, I don't really want answers that tell me to go through a series of menus on the Control Panel or download a 3rd-party application that has to stay on whichever computer the service will run on). How can I do this?

  Read the article

• Couldn't make Angry birds to work on wine

  - by Ashfame

  I could run Notepad++ easily but I fail to run the Angry bird exe. Whenever I open the exe, I see one of my screen flickrs a bit (as lines and not the whole screen) and nothing happens. Any ideas? Edit: Output of wine angrybirds.exe fixme:actctx:parse_depend_manifests Could not find dependent assembly L"Microsoft.VC80.CRT" (8.0.50727.4053) fixme:actctx:parse_depend_manifests Could not find dependent assembly L"Microsoft.VC90.CRT" (9.0.21022.8) err:module:import_dll Library MSVCP90.dll (which is needed by L"C:\\windows\\system32\\AppUpWrapper.dll") not found err:module:import_dll Library AppUpWrapper.dll (which is needed by L"C:\\windows\\system32\\angrybirds.exe") not found err:module:LdrInitializeThunk Main exe initialization for L"C:\\windows\\system32\\angrybirds.exe" failed, status c0000135 I think it didn't even install. I manually dropped those files in the folder but still no gain. Edit: Progress I dropped the file MSVCP90.dll manually and now this is what I get in the output fixme:actctx:parse_depend_manifests Could not find dependent assembly L"Microsoft.VC80.CRT" (8.0.50727.4053) fixme:actctx:parse_depend_manifests Could not find dependent assembly L"Microsoft.VC90.CRT" (9.0.21022.8) fixme:heap:HeapSetInformation 0x541000 0 0x32fd48 4 fixme:heap:HeapSetInformation (nil) 1 (nil) 0 EXCEPTION: Failed to open data/scripts/starLimits.lua wine: Unhandled exception 0x40000015 at address 0x7b880023:0x78b271d0 (thread 0009), starting debugger... fixme:msvcr90:__clean_type_info_names_internal (0x10267694) stub fixme:msvcr90:__clean_type_info_names_internal (0x78506644) stub ashfame@ashfame-desktop:~$ Process of pid=0008 has terminated No process loaded, cannot execute 'echo Modules:' Cannot get info on module while no process is loaded No process loaded, cannot execute 'echo Threads:' process tid prio (all id:s are in hex) 0000000e services.exe 00000014 0 00000010 0 0000000f 0 00000011 winedevice.exe 00000018 0 00000016 0 00000013 0 00000012 0 00000019 explorer.exe 0000001a 0 You must be attached to a process to run this command. No process loaded, cannot execute 'detach' and there the terminal hangs (I mean I would have to Ctrl + C to get out). It shows up the famous message, that it needs to close down. Edit: Just to let you know that I am still stuck at it. I don't use wine for anything else, so I am ready to do a clean install of wine and everything if anyone is willing to provide me instructions.

  Read the article

• Microsoft Excel 2007 constantly calculating sheets

  - by acseven

  I believe this happening for two weeks now: Excel 2007 (on Windows XP) is acting funny on my computer; any medium sized sheet with some formulas in it takes a significant amount of time recalculating. I can see this because the "calculating: 2 processors xx%" message was almost unseen before and now it appears on most operations like calculating a formula (on one cell), saving, previewing, etc. If the sheet is complex (lots of formulas) I have to disable automatic calculations because excel renders as unusable - it hangs for a really long time, measureable in minutes. Any idea on what may be causing this? ps: this is a Core2 Duo computer with 2 Gb of RAM

  Read the article

• sqlcmd backup script failing

  - by Bryan

  I'm trying to use a simple batch script to backup a local instance of SQL Express 2012, as follows: @echo off SET BACKUP_DIR=E:\BackupData SET SERVER=.\\sqlexpress set dom=%date:~0,2% set month=%date:~3,2% set year=%date:~6,4% set file=%year%-%month%-%dom% sqlcmd -S %SERVER% -d master -Q "exec sp_msforeachdb 'BACKUP DATABASE [?] TO DISK=''%BACKUP_DIR%\?.Full.%file%.bak''' The script is failing to run with the following error: Sqlcmd: Error: Microsoft SQL Server Native Client 10.0 : Client unable to establish connection due to prelogin failure. This is on Server 2008 R2, my SQL database (on localhost) instance is named SQLEXPRESS. There is an instance of SQL Express 2008 on the system (hence client 10.0). The database is configured to use a trusted connection, and the .net desktop software deployed on our network PCs is able to access the database without any problem. Am I missing something obvious here, I've done a fair amount of searching for this error message, and haven't found anything that has been particularly useful so far.

  Read the article

• C-panel mail goes into spam instead of inbox in gmail

  - by Robin Jain

  I have c-panel vps server. I have created a domain on the same server, but when I send mail through webmail to gmail email id it goes into the spam folder. Note--->Mail ip note blacklisted Spf records enable DKIM enable reverse dns are perfect ====================================================================== Email header Information: Delivered-To: [email protected] Received: by 10.143.93.13 with SMTP id v13csp119806wfl; Fri, 6 Jul 2012 08:01:36 -0700 (PDT) Received: by 10.182.52.42 with SMTP id q10mr26133912obo.46.1341586895571; Fri, 06 Jul 2012 08:01:35 -0700 (PDT) Return-Path: <[email protected]> Received: from lakshyacs-u.securehostdns.com ([50.97.147.134]) by mx.google.com with ESMTPS id fx3si18028369obc.144.2012.07.06.08.01.35 (version=TLSv1/SSLv3 cipher=OTHER); Fri, 06 Jul 2012 08:01:35 -0700 (PDT) Received-SPF: pass (google.com: domain of [email protected] designates 50.97.147.134 as permitted sender) client-ip=50.97.147.134; Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates 50.97.147.134 as permitted sender) [email protected] Received: from localhost.localdomain ([127.0.0.1]:39016 helo=harishjoshico.com) by lakshyacs-u.securehostdns.com with esmtpa (Exim 4.77) (envelope-from <[email protected]>) id 1SnA2J-0006Nq-05 for [email protected]; Fri, 06 Jul 2012 20:31:35 +0530 Received: from 223.189.14.213 ([223.189.14.213]) (SquirrelMail authenticated user [email protected]) by harishjoshico.com with HTTP; Fri, 6 Jul 2012 20:31:35 +0530 Message-ID: <[email protected]> Date: Fri, 6 Jul 2012 20:31:35 +0530 Subject: ggglkhl From: [email protected] To: [email protected] User-Agent: SquirrelMail/1.4.22 MIME-Version: 1.0 Content-Type: text/plain;charset=iso-8859-1 Content-Transfer-Encoding: 8bit X-Priority: 3 (Normal) Importance: Normal X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - lakshyacs-u.securehostdns.com X-AntiAbuse: Original Domain - gmail.com X-AntiAbuse: Originator/Caller UID/GID - [47 12] / [47 12] X-AntiAbuse: Sender Address Domain - harishjoshico.com jhkhl ================================================================

  Read the article

• Eclipse on mac: how comes that everytime I install an Eclipse plug-in on my mac I always get this er

  - by Patrick

  I'm using Eclipse for several projects on Leopard OSX. I've installed several versions (Classic, PDT, etc). When I install a new plug-in using the Help Install New Software functionality and I restart it, I always get the same error and I cannot anymore use it: !ENTRY org.eclipse.equinox.launcher 4 0 2010-04-20 17:32:42.540 !MESSAGE Exception launching the Eclipse Platform: !STACK java.lang.ClassNotFoundException: org.eclipse.core.runtime.adaptor.EclipseStarter at java.net.URLClassLoader$1.run(URLClassLoader.java:200) at java.security.AccessController.doPrivileged(Native Method) at java.net.URLClassLoader.findClass(URLClassLoader.java:188) at java.lang.ClassLoader.loadClass(ClassLoader.java:317) at java.lang.ClassLoader.loadClass(ClassLoader.java:252) at org.eclipse.equinox.launcher.Main.invokeFramework(Main.java:556) at org.eclipse.equinox.launcher.Main.basicRun(Main.java:514) at org.eclipse.equinox.launcher.Main.run(Main.java:1311) What is causing the error? How can I get these plugins to work? Thanks

  Read the article

• Tip 16 : Open Multiple Documents within Single Application Instance Using C#

  - by StanleyGu

  1.       Using Microsoft Word 2007 as an example, you can open test1.docx and test2.docx at same time. The two documents are opened within single instance of the word application. World application supports command line argument of passing multiple documents. 2.       Again, Using Microsoft Word 2007 as an example, you can open test1.docx first and then test2.docx. The two documents are opened within single instance of the Word application. Word application supports Multiple Document Interface (MDI). 3.       Using Notepad as an example, you receive error message of “The filename, directory name, or volume label syntax is incorrect” if you want to open two documents at the same time. Notepad does not support command line argument of passing multiple documents 4.       Again, using Notepad as an example, you can open test1.txt first and then test2.txt. The two documents are opened to two different instances of Notepad application. Notepad does not support Multiple Document Interface (MDI). 5.       In conclusion, there is nothing you can do trying to rely on System.Diagnostics.Process class to open multiple documents within a single instance of an application because it is controlled by the application itself. The best approach is to read any developer or user guide of the application and make sure: 1. The application supports Multiple Document Interface (MDI) 2. The application provides command line argument of passing multiple documents. Then, you can use Process class and the command line argument syntax to open multiple documents for the application.  

  Read the article

• Lost in Translation

  - by antony.reynolds

  Using the Correct Character Set for the SOA Suite Database A couple of years ago I spent a wonderful week in Tel Aviv helping with the first Oracle BAM implementation in Israel.  Although everyone I interacted spoke better English than I did, the screens and data for the implementation were all in Hebrew, meaning the Hebrew alphabet.  Over the week I learnt to recognize a few Hebrew words, enough to enable me to test what we were doing.  So I knew SOA Suite worked OK with non-English and non-Latin character sets so I was suspicious recently when a customer was having data corruption of non-Latin characters.  On investigation it turned out that the data received correctly in the SOA Suite, but then it was corrupted after being stored in the database. A little investigation revealed that the customer was using the default database character set, which is “WE8ISO8859P1” which, as the name suggests only supports West European 8-bit characters.  What was happening was that when the customer had installed his SOA repository he had ignored the message that his database was not using AL32UTF as the character. After changing the character set on his database he no longer saw the corruption of non-English character data. So the moral of this story is Always install the SOA Repository in to an AL32UTF8 Database This is true for both SOA Suite 10g and 11g.  Ignore it at your peril, because you never know when you will need to support Hebrew, or Japanese or another multi-byte character set.

  Read the article

• Booting from USB on Mac Air (using setup_mac_usb_boot.sh)

  - by Mike O

  So, I've been working on this for hours and it's getting a little tiring. As some of you may know, installing Ubuntu on Macs is frequently an adventure, and I'm experiencing that right now. The part I'm hung up on at the moment is making a bootable USB. I would just use a CD, but my laptop is a MacBook Air (which doesn't have a CD drive), and I don't own an external CD drive. I initially attempted to use the command line method supplied by the Ubuntu documentation here: https://help.ubuntu.com/community/How%20to%20install%20Ubuntu%20on%20MacBook%20using%20USB%20Stick However, that wasn't even recognized by rEFIt even when I made a number of different modifications to the process, so I quickly decided to look elsewhere. I came across this guide: https://help.ubuntu.com/community/MacBookAir4-2#Basic_Installation_Instructions This ended up working to a large extent. If I choose the supplied grub from rEFIt, it will bring me to the Ubuntu grub, asking me to try it, install, or check the disk. And if I choose to boot Linux directly from rEFIt, it will bring me to the language selection menu. But when I make my selection from either of these menus it pauses for about ten seconds and then gives me a command line error message. It begins with kernel panic - not syncing timer doesn't work through interrupt, and then shows about eight file names. Does anyone here have any ideas as to what can be causing this? I also tried the script with both Ubuntu 11.10 (the current version when the script was written) and 12.04.

  Read the article

• Microsoft MVP 2013 - ASP.NET/IIS

  - by hajan

  Microsoft MVP 2013 I AM VERY PLEASED TO ANNOUNCE THAT I'VE BEEN AWARDED MICROSOFT MVP 2013 - ASP.NET/IIS I'm honored and it feels great to see this kind of appreciation for what we do in community.This is my third year in a row being Microsoft MVP and getting the email from Microsoft feels exactly the same as the very first one... I'm pleased and really happy to be awarded again.And, here is part of the email message I got: Dear Hajan Selmani, Congratulations! We are pleased to present you with the 2013 Microsoft® MVP Award! This award is given to exceptional technical community leaders who actively share their high quality, real world expertise with others. We appreciate your outstanding contributions in ASP.NET/IIS technical communities during the past year. I would like to say a great THANK YOU to everyone who supports me in the quest of sharing and caring about others in community. A special THANK YOU to Microsoft who brings us this opportunity to encourage our work and increase our enthusiasm to create better community and make great impact through the products and technologies they innovate. Thanks to Yulia Belyanina & Alessandro Teglia for their leadership! Thanks to my family, friends, colleagues, students, acquaintances and all stakeholders who are directly or indirectly involved in my network and deserve respect for my success to getting awarded again with the most prestigious award in community, Microsoft MVP. THANK YOU! Hajan

  Read the article

• Configure SQL Server to Allow Remote Connections

  - by Ben Griswold

  Okay. This post isn’t about configuring SQL to allow remote connections, but wait, I still may be able to help you out. "A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 – Could not open a connection to SQL Server)" I love this exception. It summarized the issue and leads you down a path to solving the problem.  I do wish the bit about allowing remote connections was left out of the message though. I can’t think of a time when having remote connections disabled caused me grief.  Heck, I can’t ever remember how to enable remote connections unless I Google for the answer. Anyway, 9 out of 10 times, SQL Server simply isn’t running.  That’s why the exception occurs.  The next time this exception pops up, open up the services console and make sure SQL Server is started.  And if that’s not the problem, only then start digging into the other possible reasons for the failure.

  Read the article

• Virtualmin Configuration

  - by Allen

  I am trying to get Virtualmin setup and have reached a point where my noobish sysadmin skills aren't getting the job done. This is the message I get now when I try and refresh the configuration of Virtualmin. BIND DNS server is installed, and the system is configured to use it. However, the default master DNS server XXXXXX is not a fully qualified domain name. Sendmail is only accepting SMTP connections on the following ports : 127.0.0.1 port smtp. Email from other systems on the Internet will not be accepted. This can be changed in the Sendmail Mail Server module. Please advise what I need to do to get Sendmail configured properly. Thanks!

  Read the article

• DFS replication initial step problem

  - by vn

  Heya, I just setup DFS on my network and it's working fine, and now I'm trying to setup DFS-R on a test folder, but then at the end of the procedure (all went fine, selected my 2 folders, primary folder, replication topology and such) I get this error message (roughly translated from french) : Unable to define security on the replicated folder. The shared administration folder doesn't exist. I'm also wondering if there's any required security on the folders to replicate so that DFS-R can access it. I was trying to add SYSTEM in the security, but it won't find it/allow me. The folder has many many files and folders on the primary DFS pointer, but none on the 2nd, just created it with quite the same rights. Note that the primary DFS pointer is on a 2008 server and the DFS service and the secondary DFS pointer are on a 2008r2. Any help is very appreciated, thanks.

  Read the article

• Server Core remote management from Windows 7 machine

  - by Robert Koritnik

  I've installed Remote Server Administration Tools for Windows 7 because I would like to administer my Windows Server 2008 R2 Server Core machine. The problem that I'm getting when I try to run Server Manager is: Connecting to remote server failed with the following error message: Access is denied. For more information, see the about_Remote_Troubleshooting Help topic. This is what I've done so far: I'm running WinRM service on both machines (Server and Window 7) I've added my server to trusted hosts on my Windows 7 machine: winrm set winrm/config/client @{TrustedHosts="WINSRV2"} I've added registry entry on Windows 7 machine: reg add HKLM\SOFTWARE\Microsoft\Windows\CurrentVersion\Policies\System /v LocalAccountTokenFilterPolicy /t REG_DWORD /d 1 /f I've enabled Remote Management inbound rule on server firewall using CoreConfigurator 2.0 both machines are in the same subnet and when I search for network machines on Windows 7 I see my server. Question What else should I do to make it work? I would like to run several different remote management tools against my server machine.

  Read the article

• How to access apache behind home router?

  - by Filip

  Hi! I have public IP 89.103.xxx.yyy, then router and home network with 192.168.1.zz My router is set to portforward every 8056 on ip adress 192.168.1.5 (my PC), where apache is running. Apache listen is set to: Listen 127.0.0.1:80 Listen 192.168.1.5:8056 When i try: Listen 89.103.xxx.yyy:8056 I get message "unexpected end of apache" (I'm using easyphp for windows). Added: When i try to access 89.103.xxx.yyy via browser, it's prompting router request for authorization to access router web-settings. And when i try 89.103.xxx.yyy:8056, browser says that connection timed out =(

  Read the article

• Introduction to LinqPad Driver for StreamInsight 2.1

  - by Roman Schindlauer

  We are announcing the availability of the LinqPad driver for StreamInsight 2.1. The purpose of this blog post is to offer a quick introduction into the new features that we added to the StreamInsight LinqPad driver. We’ll show you how to connect to a remote server, how to inspect the entities present of that server, how to compose on top of them and how to manage their lifetime. Installing the driver Info on how to install the driver can be found in an earlier blog post here. Establishing connections As you click on the “Add Connection” link in the left pane you will notice that now it’s possible to build the data context automatically. The new driver appears as an option in the upper list, and if you pick it you will open a connection dialog that lets you connect to a remote StreamInsight server. The connection dialog lets you specify the address of the remote server. You will notice that it’s possible to pick up the binding information from the configuration file of the LinqPad application (which is normally in the same folder as LinqPad.exe and is called LinqPad.exe.config). In order for the context to be generated you need to pick an application from the server. The control is editable hence you can create a new application if you don’t want to make changes to an existing application. If you choose a new application name you will be prompted for confirmation before this gets created. Once you click OK the connection is created and you can start issuing queries against the remote server. If there’s any connectivity error the connection is marked with a red X and you can see the error message informing you what went wrong (i.e., the remote server could not be reached etc.). The context for remote servers Let’s take a look at what happens after we are connected successfully. Every LinqPad query runs inside a context – think of it as a class that wraps all the code that you’re writing. If you’re connecting to a live server the context will contain the following: The application object itself. All entities present in this application (sources, sinks, subjects and processes). The picture below shows a snapshot of the left pane of LinqPad after a successful connection. Every entity on the server has a different icon which will allow users to figure out its purpose. You will also notice that some entities have a string in parentheses following the name. It should be interpreted as such: the first name is the name of the property of the context class and the second name is the name of the entity as it exists on the server. Not all valid entity names are valid identifier names so in cases where we had to make a transformation you see both. Note also that as you hover over the entities you get IntelliSense with their types – more on that later. Remoting is not supported As you play with the entities exposed by the context you will notice that you can’t read and write directly to/from them. If for instance you’re trying to dump the content of an entity you will get an error message telling you that in the current version remoting is not supported. This is because the entity lives on the remote server and dumping its content means reading the events produced by this entity into the local process. ObservableSource.Dump(); Will yield the following error: Reading from a remote 'System.Reactive.Linq.IQbservable`1[System.Int32]' is not supported. Use the 'Microsoft.ComplexEventProcessing.Linq.RemoteProvider.Bind' method to read from the source using a remote observer. This basically tells you that you can call the Bind() method to direct the output of this source to a sink that has to be defined on the remote machine as well. You can’t bring the results to the LinqPad window unless you write code specifically for that. Compose queries You may ask – what's the purpose of all that? After all the same information is present in the EventFlowDebugger, why bother with showing it in LinqPad? First of all, What gets exposed in LinqPad is not what you see in the debugger. In LinqPad we have a property on the context class for every entity that lives on the server. Because LinqPad offers IntelliSense we in fact have much more information about the entity, and more importantly we can compose with that entity very easily. For example, let’s say that this code creates an entity: using (var server = Server.Connect(...)) {     var a = server.CreateApplication("WhiteFish");     var src = a         .DefineObservable<int>(() => Observable.Range(0, 3))         .Deploy("ObservableSource"); If later we want to compose with the source we have to fetch it and then we can bind something to     a.GetObservable<int>("ObservableSource)").Bind(... This means that we had to know a bunch of things about this: that it’s a source, that it’s an observable, it produces a result with payload Int32 and it’s named “ObservableSource”. Only the second and last bits of information are present in the debugger, by the way. As you type in the query window you see that all the entities are present, you get IntelliSense support for them and it’s much easier to make sense of what’s available. Let’s look at a scenario where composition is plausible. With the new programming model it’s possible to create “cold” sources that are parameterized. There was a way to accomplish that even in the previous version by passing parameters to the adapters, but this time it’s much more elegant because the expression declares what parameters are required. Say that we hover the mouse over the ThrottledSource source – we will see that its type is Func<int, int, IQbservable<int>> - this in effect means that we need to pass two int parameters before we can get a source that produces events, and the type for those events is int – in the particular case of my example I had the source produce a range of integers and the two parameters were the start and end of the range. So we see how a developer can create a source that is not running yet. Then someone else (e.g. an administrator) can pass whatever parameters appropriate and run the process. Proxy Types Here’s an interesting scenario – what if someone created a source on a server but they forgot to tell you what type they used. Worse yet, they might have used an anonymous type and even though they can refer to it by name you can’t figure out how to use that type. Let’s walk through an example that shows how you can compose against types you don’t need to have the definition of. This is how we can create a source that returns an anonymous type: Application.DefineObservable(() => Observable.Range(1, 10).Select(i => new { I = i })).Deploy("O1"); Now if we refresh the connection we can see the new source named O1 appear in the list. But what’s more important is that we now have a type to work with. So we can compose a query that refers to the anonymous type. var threshold = new StreamInsightDynamicDriver.TypeProxies.AnonymousType1_0<int>(5); var filter = from i in O1              where i > threshold              select i; filter.Deploy("O2"); You will notice that the anonymous type defined with this statement: new { I = i } can now be manipulated by a client that does not have access to it because the LinqPad driver has generated another type in its stead, named StreamInsightDynamicDriver.TypeProxies.AnonymousType1_0. This type has all the properties and fields of the type defined on the server, except in this case we can instantiate values and use it to compose more queries. It is worth noting that the same thing works for types that are not anonymous – the test is if the LinqPad driver can resolve the type or not. If it’s not possible then a new type will be generated that approximates the type that exists on the server. Control metadata In addition to composing processes on top of the existing entities we can do other useful things. We can delete them – nothing new here as we simply access the entities through the Entities collection of the application class. Here is where having their real name in parentheses comes handy. There’s another way to find out what’s behind a property – dump its expression. The first line in the output tells us what’s the name of the entity used to build this property in the context. Runtime information So let’s create a process to see what happens. We can bind a source to a sink and run the resulting process. If you right click on the connection you can refresh it and see the process present in the list of entities. Then you can drag the process to the query window and see that you can have access to process object in the Processes collection of the application. You can then manipulate the process (delete it, read its diagnostic view etc.). Regards, The StreamInsight Team

  Read the article

• Authentication problem: can't bypass the login prompt when browsing to the SQL Reporing Services web

  - by laurens

  Hi all, I'm having a hard time configuring Reporting services on one of our servers. I'm not uninitiated in the domain of IIS7 but I cannot get rid of the login prompt when I'm surfing to the Reporting services website. What I did: I made a windows and SQL user with the same name: Then I choose Anonymous authentication in II7 and filled in the credentials of the specific R.S. user http://img32.imageshack.us/i/iis7auth.jpg/ I choose 'Local Service' as the service account in the R.S. configuration mgr http://img88.imageshack.us/i/rsconfigmgr.jpg/ The first problem is that there's always a pop-up when surfing to the website The second is that when I'm able to log in I get the message that the user doesn't have the appropriate permissions. The pop-up: http://img693.imageshack.us/i/loginpopup.jpg/ The server is a 2008 Web Server with SQL 2008 R2 Express. What I'm I doing wrong? Thanks in advance!

  Read the article

• Restrict SSL access for some paths on a apache2 server

  - by valmar

  I wanted to allow access to www.mydomain.com/login through ssl only. E.g.: Whenever someone accessed http://www.mydomain.com/login, I wanted him to be redirect to https://www.mydomain.com/login so it's impossible for him/her to access that site without SSL. I accomplished this by adding the following lines to the virtual host for www.mydomain.com on port 80 in /etc/apache2/sites-available/default: RewriteEngine on RewriteCond %{SERVER_PORT} ^80$ RewriteRule ^/login(.*)$ https://%{SERVER_NAME}/login$1 [L,R] RewriteLog "/var/log/apache2/rewrite.log" Now, I want to restrict using SSL for www.mydomain.com. That means, whenever someone accessed https://www.mydomain.com, I want him to be redirected to http://www.mydomain.com (for performance reasons). I tried this by adding the following lines to the virtual host of www.mydomain.com on port 443 in /etc/apache2/sites-available/default-ssl: RewriteEngine on RewriteCond %{SERVER_PORT} ^443$ RewriteRule ^/(.*)$ http://%{SERVER_NAME}/$1 [L,R] RewriteLog "/var/log/apache2/rewrite.log" But when I now try to access www.mydomain.com/login, I get an error message that the server has caused to many redirects. That does make sense. Obviously, the two RewriteRules are playing ping-pong against each other. How could I work around this?

  Read the article

• syslogd: Logfile format (not configuration format)

  - by chris_l

  Hi, I'd like to parse logfiles. Is the logfile format of syslogd the same for all systems? On my system (Debian Lenny), it's: Mar 7 04:22:40 my-host-name ... (I'm not much interested in the ... part) Can I rely on this? And is there maybe some more-or-less official description? The manpage of syslogd describes the config format, but not the logfile format. Ideally, the description would give the fields official names like (date, time, host, entry) or (datetime, hostname, message). Maybe additionally some regular expressions. I'd like to use the names and regexes in my script, to avoid an unnecessary deviation from the standard, and to make sure, that the script runs everywhere. Thanks Chris

  Read the article

• WebDAV "PROPFIND" exception in IIS due to network share?

  - by jacko

  Hi all, We're finding continuous exceptions in our event viewer on our live box to the following exception: [snippet] Process information: Process ID: 3916 Process name: w3wp.exe Account name: NT AUTHORITY\NETWORK SERVICE Exception information: Exception type: HttpException Exception message: Path 'PROPFIND' is forbidden. Thread information: Thread ID: 14 Thread account name: OURDOMAIN\Account Is impersonating: True Stack trace: at System.Web.HttpMethodNotAllowedHandler.ProcessRequest(HttpContext context) at System.Web.HttpApplication.CallHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) Other Specs: Windows Server 2003 R2 & IIS 6.0 We've narrowed it down to occuring when people try to access shares on the box from within the network, and have discovered (we think) that its due to the WebDAV web services extension being previously disabled by past staff. The exceptions are being thrown when trying to access directories that are virtual dirs in IIS, and plain old UNC network shares What the implications for enabling the WebDAV extensions on our live web server? And will this solve our problems with the exceptions in our event log?

  Read the article

• Cannot uninstall myspell-he

  - by Yuval Rabinovich

  I tried to install a Hebrew spell checker for LibreOffice. I downloaded a package named myspell-he_1.1-1_all.deb and tried to install it through the software center, installation failed and I can neither complete installation nor remove it. Since then, whenever I run Update Manager I get an error message: The package system is broken, In details: The following packages have unmet dependencies: dictionaries-common: When I try to run the Software center I get a pop-up window: Items cannot be installed or removed until the package catalog is repaired. A Repair option is suggested. If I click it the following nessage appears: installArchives() failed: dpkg: dependency problems prevent configuration of myspell-he: dictionaries-common (1.12.1ubuntu2) breaks myspell-he (<= 1.1-1) and is installed. Version of myspell-he to be configured is 1.1-1. dpkg: error processing myspell-he (--configure): dependency problems - leaving unconfigured No apport report written because MaxReports is reached already Errors were encountered while processing: myspell-he Error in function: dpkg: dependency problems prevent configuration of myspell-he: dictionaries-common (1.12.1ubuntu2) breaks myspell-he (<= 1.1-1) and is installed. Version of myspell-he to be configured is 1.1-1. dpkg: error processing myspell-he (--configure): dependency problems - leaving unconfigured How can I clear this mess?

  Read the article

< Previous Page | 437 438 439 440 441 442 443 444 445 446 447 448  | Next Page >