Search Results

Search found 15248 results on 610 pages for 'slashdot configuration'.

Page 444/610 | < Previous Page | 440 441 442 443 444 445 446 447 448 449 450 451  | Next Page >

• 64-bit 13.10 shows 1GB less RAM than 64-bit 13.04 did

  - by kiloseven

  Multiple 64-bit versions (Kubuntu, Lubuntu and Xubuntu) once installed on my ThinkPad R60 show 3GB of RAM, not the correct 4GB of RAM. Last week with 13.04, I had 4GB of RAM (which matches the BIOS) and this week I have 3GB available. Inquiring minds want to know. Details follow: Linux R60 3.11.0-12-generic #19-Ubuntu SMP Wed Oct 9 16:20:46 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux r60 free -m reports: _ total used free shared buffers cached Mem: 3001 854 2146 0 22 486 -/+ buffers/cache: 346 2655 Swap: 0 0 0 . . . . . . lshw shows: description: Notebook product: 9459AT8 () vendor: LENOVO version: ThinkPad R60/R60i serial: redacted width: 64 bits capabilities: smbios-2.4 dmi-2.4 vsyscall32 configuration: administrator_password=disabled boot=normal chassis=notebook family=ThinkPad R60/R60i frontpanel_password=unknown keyboard_password=disabled power-on_password=disabled uuid=126E4001-48CA-11CB-9D53-B982AE0D1ABB *-core description: Motherboard product: 9459AT8 vendor: LENOVO physical id: 0 version: Not Available *-firmware description: BIOS vendor: LENOVO physical id: 0 version: 7CETC1WW (2.11 ) date: 01/09/2007 size: 144KiB capacity: 1984KiB capabilities: pci pcmcia pnp upgrade shadowing escd cdboot bootselect socketedrom edd acpi usb biosbootspecification {snip} *-memory description: System Memory physical id: 29 slot: System board or motherboard size: 4GiB *-bank:0 description: SODIMM DDR2 Synchronous physical id: 0 slot: DIMM 1 size: 2GiB width: 64 bits *-bank:1 description: SODIMM DDR2 Synchronous physical id: 1 slot: DIMM 2 size: 2GiB width: 64 bits dpkg -l linux-* returns: Desired=Unknown/Install/Remove/Purge/Hold | Status=Not/Inst/Conf-files/Unpacked/halF-conf/Half-inst/trig-aWait/Trig-pend |/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad) ||/ Name Version Description +++-======================================-=======================================-========================================================================== un linux-doc-3.2.0 (no description available) ii linux-firmware 1.79.6 Firmware for Linux kernel drivers ii linux-generic 3.2.0.52.62 Complete Generic Linux kernel un linux-headers (no description available) un linux-headers-3 (no description available) un linux-headers-3.0 (no description available) un linux-headers-3.2.0-23 (no description available) un linux-headers-3.2.0-23-generic (no description available) ii linux-headers-3.2.0-52 3.2.0-52.78 Header files related to Linux kernel version 3.2.0 ii linux-headers-3.2.0-52-generic 3.2.0-52.78 Linux kernel headers for version 3.2.0 on 64 bit x86 SMP ii linux-headers-generic 3.2.0.52.62 Generic Linux kernel headers un linux-image (no description available) un linux-image-3.0 (no description available) ii linux-image-3.2.0-52-generic 3.2.0-52.78 Linux kernel image for version 3.2.0 on 64 bit x86 SMP ii linux-image-generic 3.2.0.52.62 Generic Linux kernel image un linux-initramfs-tool (no description available) un linux-kernel-headers (no description available) un linux-kernel-log-daemon (no description available) ii linux-libc-dev 3.2.0-52.78 Linux Kernel Headers for development un linux-restricted-common (no description available) ii linux-sound-base 1.0.25+dfsg-0ubuntu1.1 base package for ALSA and OSS sound systems un linux-source-3.2.0 (no description available) un linux-tools (no description available)

  Read the article

• How to update all the SSIS packages&rsquo; Connection Managers in a BIDS project with PowerShell

  - by Luca Zavarella

  During the development of a BI solution, we all know that 80% of the time is spent during the ETL (Extract, Transform, Load) phase. If you use the BI Stack Tool provided by Microsoft SQL Server, this step is accomplished by the development of n Integration Services (SSIS) packages. In general, the number of packages made ??in the ETL phase for a non-trivial solution of BI is quite significant. An SSIS package, therefore, extracts data from a source, it "hammers" :) the data and then transfers it to a specific destination. Very often it happens that the connection to the source data is the same for all packages. Using Integration Services, this results in having the same Connection Manager (perhaps with the same name) for all packages: The source data of my BI solution comes from an Helper database (HLP), then, for each package tha import this data, I have the HLP Connection Manager (the use of a Shared Data Source is not recommended, because the Connection String is wired and therefore you have to open the SSIS project and use the proper wizard change it...). In order to change the HLP Connection String at runtime, we could use the Package Configuration, or we could run our packages with DTLoggedExec by Davide Mauri (a must-have if you are developing with SQL Server 2005/2008). But my need was to change all the HLP connections in all packages within the SSIS Visual Studio project, because I had to version them through Team Foundation Server (TFS). A good scribe with a lot of patience should have changed by hand all the connections by double-clicking the HLP Connection Manager of each package, and then changing the referenced server/database: Not being endowed with such virtues :) I took just a little of time to write a small script in PowerShell, using the fact that a SSIS package (a .dtsx file) is nothing but an xml file, and therefore can be changed quite easily. I'm not a guru of PowerShell, but I managed more or less to put together the following lines of code: $LeftDelimiterString = "Initial Catalog=" $RightDelimiterString = ";Provider=" $ToBeReplacedString = "AstarteToBeReplaced" $ReplacingString = "AstarteReplacing" $MainFolder = "C:\MySSISPackagesFolder" $files = get-childitem "$MainFolder" *.dtsx `       | Where-Object {!($_.PSIsContainer)} foreach ($file in $files) {       (Get-Content $file.FullName) `             | % {$_ -replace "($LeftDelimiterString)($ToBeReplacedString)($RightDelimiterString)", "`$1$ReplacingString`$3"} ` | Set-Content $file.FullName; } The script above just opens any SSIS package (.dtsx) in the supplied folder, then for each of them goes in search of the following text: Initial Catalog=AstarteToBeReplaced;Provider= and it replaces the text found with this: Initial Catalog=AstarteReplacing;Provider= I don’t enter into the details of each cmdlet used. I leave the reader to search for these details. Alternatively, you can use a specific object model exposed in some .NET assemblies provided by Integration Services, or you can use the Pacman utility: Enjoy! :) P.S. Using TFS as versioning system, before running the script I checked out the packages and, after the script executed succesfully, I checked in them.

  Read the article

• Web.Config is Cached

  - by SGWellens

  There was a question from a student over on the Asp.Net forums about improving site performance. The concern was that every time an app setting was read from the Web.Config file, the disk would be accessed. With many app settings and many users, it was believed performance would suffer. Their intent was to create a class to hold all the settings, instantiate it and fill it from the Web.Config file on startup. Then, all the settings would be in RAM. I knew this was not correct and didn't want to just say so without any corroboration, so I did some searching. Surprisingly, this is a common misconception. I found other code postings that cached the app settings from Web.Config. Many people even thanked the posters for the code. In a later post, the student said their text book recommended caching the Web.Config file. OK, here's the deal. The Web.Config file is already cached. You do not need to re-cache it. From this article http://msdn.microsoft.com/en-us/library/aa478432.aspx It is important to realize that the entire <appSettings> section is read, parsed, and cached the first time we retrieve a setting value. From that point forward, all requests for setting values come from an in-memory cache, so access is quite fast and doesn't incur any subsequent overhead for accessing the file or parsing the XML. The reason the misconception is prevalent may be because it's hard to search for Web.Config and cache without getting a lot of hits on how to setup caching in the Web.Config file. So here's a string for search engines to index on: "Is the Web.Config file Cached?" A follow up question was, are the connection strings cached? Yes. http://msdn.microsoft.com/en-us/library/ms178683.aspx At run time, ASP.NET uses the Web.Config files to hierarchically compute a unique collection of configuration settings for each incoming URL request. These settings are calculated only once and then cached on the server. And, as everyone should know, if you modify the Web.Config file, the web application will restart. I hope this helps people to NOT write code! Steve WellensCodeProject

  Read the article

• Web.Config is Cached

  - by SGWellens

  There was a question from a student over on the Asp.Net forums about improving site performance. The concern was that every time an app setting was read from the Web.Config file, the disk would be accessed. With many app settings and many users, it was believed performance would suffer. Their intent was to create a class to hold all the settings, instantiate it and fill it from the Web.Config file on startup. Then, all the settings would be in RAM. I knew this was not correct and didn't want to just say so without any corroboration, so I did some searching. Surprisingly, this is a common misconception. I found other code postings that cached the app settings from Web.Config. Many people even thanked the posters for the code. In a later post, the student said their text book recommended caching the Web.Config file. OK, here's the deal. The Web.Config file is already cached. You do not need to re-cache it. From this article http://msdn.microsoft.com/en-us/library/aa478432.aspx It is important to realize that the entire <appSettings> section is read, parsed, and cached the first time we retrieve a setting value. From that point forward, all requests for setting values come from an in-memory cache, so access is quite fast and doesn't incur any subsequent overhead for accessing the file or parsing the XML. The reason the misconception is prevalent may be because it's hard to search for Web.Config and cache without getting a lot of hits on how to setup caching in the Web.Config file. So here's a string for search engines to index on: "Is the Web.Config file Cached?" A follow up question was, are the connection strings cached? Yes. http://msdn.microsoft.com/en-us/library/ms178683.aspx At run time, ASP.NET uses the Web.Config files to hierarchically compute a unique collection of configuration settings for each incoming URL request. These settings are calculated only once and then cached on the server. And, as everyone should know, if you modify the Web.Config file, the web application will restart. I hope this helps people to NOT write code!   Steve WellensCodeProject

  Read the article

• E: mkinitramfs failure cpio 141 gzip 1

  - by Nagaraj Shindagi

  I'm using Ubuntu 12.04 LTS with Dell power-edge R720 server, facing the problem when I apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 2 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Setting up linux-image-3.2.0-37-generic-pae (3.2.0-37.58) ... Running depmod. update-initramfs: deferring update (hook will be called later) The link /initrd.img is a dangling linkto /boot/initrd.img-3.2.0-37-generic-pae Examining /etc/kernel/postinst.d. run-parts: executing /etc/kernel/postinst.d/initramfs-tools 3.2.0-37-generic-pae /boot/vmlinuz-3.2.0-37-generic-pae update-initramfs: Generating /boot/initrd.img-3.2.0-37-generic-pae gzip: stdout: No space left on device E: mkinitramfs failure cpio 141 gzip 1 update-initramfs: failed for /boot/initrd.img-3.2.0-37-generic-pae with 1. run-parts: /etc/kernel/postinst.d/initramfs-tools exited with return code 1 Failed to process /etc/kernel/postinst.d at /var/lib/dpkg/info/linux-image-3.2.0 -37-generic-pae.postinst line 1010. dpkg: error processing linux-image-3.2.0-37-generic-pae (--configure): subprocess installed post-installation script returned error exit status 2 dpkg: dependency problems prevent configuration of linux-image-generic-pae: linux-image-generic-pae depends on linux-image-3.2.0-37-generic-pae; however: Package linux-image-3.2.0-37-generic-pae is not configured yet. dpkg: error processing linux-image-generic-pae (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup erro r from a previous failure. Errors were encountered while processing: linux-image-3.2.0-37-generic-pae linux-image-generic-pae E: Sub-process /usr/bin/dpkg returned an error code (1) ------------ even i tried with apt-get clean apt-get remove apt-get autoremove apt-get purge there is no difference it will show the same error message as above, even i checked the disk space ----------- Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda6 24030076 612456 22196964 3% / udev 16536644 4 16536640 1% /dev tmpfs 6618884 1164 6617720 1% /run none 5120 0 5120 0% /run/lock none 16547208 72 16547136 1% /run/shm cgroup 16547208 0 16547208 0% /sys/fs/cgroup /dev/sda1 93207 75034 13361 85% /boot /dev/sda10 9611492 1096076 8027176 13% /tmp /dev/sda12 9611492 226340 8896912 3% /opt /dev/sda13 9611492 152516 8970736 2% /srv /dev/sda7 9611492 592208 8531044 7% /home /dev/sda8 9611492 2656736 6466516 30% /usr /dev/sda9 9611492 696468 8426784 8% /var /dev/sda14 961237336 134563516 777845764 15% /usr/data /dev/sda15 618991384 84498388 503050052 15% /usr/data1 /dev/sda11 9611492 152616 8970636 2% /usr/local --------------- is there any problem on allotting the space to the partiations please let me know the solution its on urgent please help me on this issue regards

  Read the article

• Oracle Enterprise Manager users present today at Oracle Users Forum

  - by Anand Akela

  Oracle Users Forum starts in a few minutes at Moscone West, Levels 2 & 3. There are more than hundreds of Oracle user sessions during the day. Many Oracle Oracle Enterprise Manager users are presenting today as well.  In addition, we will have a Twitter Chat today from 11:30 AM to 12:30 PM with IOUG leaders, Enterprise Manager SIG contributors and many speakers. You can participate in the chat using hash tag #em12c on Twitter.com or by going to  tweetchat.com/room/em12c      (Needs Twitter credential for participating).  Feel free to join IOUG and Enterprise team members at the User Group Pavilion on 2nd Floor, Moscone West. RSVP by going http://tweetvite.com/event/IOUG  . Don't miss the Oracle Open World welcome keynote by Larry Ellison this evening at 5 PM . Here is the complete list of Oracle Enterprise Manager sessions during the Oracle Users Forum : Time Session Title Speakers Location 8:00AM - 8:45AM UGF4569 - Oracle RAC Migration with Oracle Automatic Storage Management and Oracle Enterprise Manager 12c VINOD Emmanuel -Database Engineering, Dell, Inc. Wendy Chen - Sr. Systems Engineer, Dell, Inc. Moscone West - 2011 8:00AM - 8:45AM UGF10389 -  Monitoring Storage Systems for Oracle Enterprise Manager 12c Anand Ranganathan - Product Manager, NetApp Moscone West - 2016 9:00AM - 10:00AM UGF2571 - Make Oracle Enterprise Manager Sing and Dance with the Command-Line Interface Ray Smith - Senior Database Administrator, Portland General Electric Moscone West - 2011 10:30AM - 11:30AM UGF2850 - Optimal Support: Oracle Enterprise Manager 12c Cloud Control, My Oracle Support, and More April Sims - DBA, Southern Utah University Moscone West - 2011 12:30PM-2:00PM UGF5131 - Migrating from Oracle Enterprise Manager 10g Grid Control to 12c Cloud Control    Leighton Nelson - Database Administrator, Mercy Moscone West - 2011 2:15PM-3:15PM UGF6511 -  Database Performance Tuning: Get the Best out of Oracle Enterprise Manager 12c Cloud Control Mike Ault - Oracle Guru, TEXAS MEMORY SYSTEMS INC Tariq Farooq - CEO/Founder, BrainSurface Moscone West - 2011 3:30PM-4:30PM UGF4556 - Will It Blend? Verifying Capacity in Server and Database Consolidations Jeremiah Wilton - Database Technology, Blue Gecko / DatAvail Moscone West - 2018 3:30PM-4:30PM UGF10400 - Oracle Enterprise Manager 12c: Monitoring, Metric Extensions, and Configuration Best Practices Kellyn Pot'Vin - Sr. Technical Consultant, Enkitec Moscone West - 2011 Stay Connected: Twitter |  Face book |  You Tube |  Linked in |  Newsletter

  Read the article

• Stackify Aims to Put More ‘Dev’ in ‘DevOps’

  - by Matt Watson

  Originally published on VisualStudioMagazine.com on 8/22/2012 by Keith Ward.The Kansas City-based startup wants to make it easier for developers to examine the network stack and find problems in code.The first part of “DevOps” is “Dev”. But according to Matt Watson, Devs aren’t connected enough with Ops, and it’s time that changed.He founded the startup company Stackify earlier this year to do something about it. Stackify gives developers unprecedented access to the IT side of the equation, Watson says, without putting additional burden on the system and network administrators who ultimately ensure the health of the environment.“We need a product designed for developers, with the goal of getting them more involved in operations and app support. Now, there’s next to nothing designed for developers,” Watson says. Stackify allows developers to search the network stack to troubleshoot problems in their software that might otherwise take days of coordination between development and IT teams to solve.Stackify allows developers to search log files, configuration files, databases and other infrastructure to locate errors. A key to this is that the developers are normally granted read-only access, soothing admin fears that developers will upload bad code to their servers.Implementation starts with data collection on the servers. Among the information gleaned is application discovery, server monitoring, file access, and other data collection, according to Stackify’s Web site. Watson confirmed that Stackify works seamlessly with virtualized environments as well.Although the data collection software must be installed on Windows servers, it can monitor both Windows and Linux servers. Once collection’s finished, developers have the kind of information they need, without causing heartburn for the IT staff.Stackify is a 100 percent cloud-based service. The company uses Windows Azure for hosting, a decision Watson’s happy with. With Azure, he says, “It’s nice to have all the dev tools like cache and table storage.” Although there have been a few glitches here and there with the service, it’s run very smoothly for the most part, he adds.Stackify is currently in a closed beta, with a public release scheduled for October. Watson says that pricing is expected to be $25 per month, per server, with volume discounts available. He adds that the target audience is companies with at least five developers.Watson founded Stackify after selling his last company, VinSolutions, to AutoTrader.com for “close to $150 million”, according to press accounts. Watson has since  founded the Watson Technology Group, which focuses on angel investing.About the Author: Keith Ward is the editor in chief of Visual Studio Magazine.

  Read the article

• TFS Auto Shelve - New Visual Studio 2010 / TFS 2010 Extension

  - by MikeParks

  We've been working with the Visual Studio 2010 SDK and the TFS 2010 SDK a lot recently to create new Visual Studio Extensions. You can find these extensions in the Visual Studio Gallery. If you're a developer/programmer, you should check it out, they have some pretty cool tools out there. I'd be surprised if you told me you went there and couldn't find any tools that could help you. One of the new extensions Cory and I made is called TFS Auto Shelve. Check out the description and read about it below. If you're interested and you have VS 2010 w/TFS 2010, feel free to try it out and let us know what you think. You can download it here: http://visualstudiogallery.msdn.microsoft.com/en-us/080540cb-e35f-4651-b71c-86c73e4a633d   Here's a description and screenshots of what it does: Automatically shelves the latest version of all pending changes from local TFS workspaces to the TFS Server every "x" number of minutes when solutions are opened.   ·         Purpose o    Created for Team Foundation Server 2010 and Visual Studio 2010 o    This tool is mainly aimed at the Programmer/Developer audience so they can always have the latest copy of their pending changes backed up to the TFS Server while coding ·         Functionality o    Menu options become active and automatic shelving begins when a solution that mapped to a TFS Workspace is opened in Visual Studio o    In Tools > TFS Auto Shelve (Running/NotRunning):  Automatic shelving can be turned on/off o    In Tools > TFS Auto Shelve Now : Shelve all code can be manually triggered o    Each TFS workspace has its own shelveset which is re-used to save the latest version of pending changes o    Shelvesets are named as Base Name + Workspace Name o    Shelveset comment contains item count o    If there are no pending changes, no shelvesets will be created/updated o    If a solution is opened that is not mapped to a TFS Workspace, menu options are disabled since shelving only works for mapped workspaces. ·         Configuration o    In Tools > Options > TFS Auto Shelve Options: Base Name is configurable o    In Tools > Options > TFS Auto Shelve Options: "x" number of minutes is configurable in options ·         Logging o    Custom Visual Studio Activity Logging is implemented. If you run into any errors, please startup Visual Studio with the /log switch, re-create the error, then close Visual Studio. You can browse to “%AppData%\Microsoft\VisualStudio\10.0\ActivityLog.XML” to view the log. Please feel free to inform us of any errors you see and we can work it out via email. ·         Other Helpful Information o    To view shelvesets, open Source Control Explorer, click on File > Source Control > Unshelve Pending Changes o    Workspaces can be modified by opening the Source Control Explorer > Clicking on Workspaces drop down > Click Workspaces… > Click Add / Edit / Removed   Thanks! - Mike

  Read the article

• Silverlight Cream for May 02, 2010 -- #854

  - by Dave Campbell

  In this Issue: Michael Washington, Jason Young(-2-, -3-), Phil Middlemiss, Jeremy Likness, Victor Gaudioso, Kunal Chowdhury, Antoni Dol, and Jacek Ciereszko(-2-). Shoutout: Victor Gaudioso has aggregated All of My Silverlight Video Tutorials in One Place (revised again 05.02.10) From SilverlightCream.com: Unit Testing A Silverlight 'Simplified MVVM' Modal Popup Michael Washington's latest 'Simplified MVVM' post is published at The Code Project and is on Unit Testing with MVVM. Input Localization in Silverlight without IValueConverter Jason Young sent me some links to posts I've not seen... this first one is on localization by using the Language property of the Root Visual. MVVM – The Model - Part 1 – INotifyPropertyChanged Jason Young's next archive post is the first of a series on MVVM and Silverlight 4 ... implementing a simple ViewModel base class. Silverlight, WCF, and ASP.Net Configuration Gotchas Jason Young worked at tracking down the answers to some forum questions and in the process has produced a post of 'gotchas' with using WCF in Silverlight. A Chrome and Glass Theme - Part 5 Phil Middlemiss has part 5 of his Chrome and Glass Theme tutorial up ... in this one, he's looking at the Progress Bar and Slider. Download the files and play along. Silverlight Out of Browser (OOB) Versions, Images, and Isolated Storage Jeremy Likness has a post up responding to his 3 major questions about OOB apps, and he has to code up for the sample too. New Silverlight Video Tutorial: How to Make a Slide In/Out Navigation Bar – All in Blend Victor Gaudioso's latest video tutorial is on building a Behavior for a Slide in/out Navigation bar... kinda like the menu sliders on my GlyphMap Utility... only easier! Command Binding in Silverlight 4 (Step-by-Step) Kunal Chowdhury has another post up at DotNetFunda, and this time he's talking about Command Binding in Silverlight 4 with an eye toward MVVM usage. The Silverlight PageCurl implementation Antoni Dol has a post up about doing a Page Curl effect in Silverlight. He has a manual up on the effect and full application code. How to center and scale Silverlight applications using ViewBox control Jacek Ciereszko has a couple posts up about centering and scaling your app with the ViewBox control. This first one is a code solution. Source is available, as is a Polish version. Silverlight Center And Scale Behavior Jacek Ciereszko's 2nd post, he provides a Behavior that handles the scaling and centering of the previous post. Stay in the 'Light! Twitter SilverlightNews | Twitter WynApse | WynApse.com | Tagged Posts | SilverlightCream Join me @ SilverlightCream | Phoenix Silverlight User Group Technorati Tags: Silverlight    Silverlight 3    Silverlight 4    Windows Phone MIX10

  Read the article

• Tulsa Azure Boot Camp

  - by dmccollough

  Windows Azure Boot Camp presented by HyperVize & TulsaTech When: Thursday July 1st and Friday July 2nd Registration: Click here. Where: TulsaTech Riverside Campus 801 East 91st Street Tulsa, Ok 74132-4008 Click here for a map. Summary Tulsa Windows Azure Boot Camp is a comprehensive 2 day training program for members of the development community in Tulsa Oklahoma. At the conclusion of this program, the attendees should have a deep understanding of Azure, BPOS, and advanced development techniques for both platforms. Who should attend: Web Developers, Backend Developers, SQL DBAs, Consultants, & IT Leaders who are interested in using Azure for development, data storage, or processing. Both days is suggested, but if you can't attend both days, contact us for a special one day pass. Schedule: Day one of the training sessions will be held from July 1st 2010 between the hours of 9AM and 4:30PM. Topics covered on day 1: Azure Basics, Web Development, & Data Storage. Day two of the training sessions will be held from July 2nd 2010 between the hours of 9AM and 4:30PM. Topics covered on day 2: Architecture, Business Value, SOA Development, SQL Azure, & Advanced Development. Pre-requisites: If you want to stay up to speed on the Windows Azure Labs you will need to install the tools and updates listed on the Windows Azure Boot Camp website: http://windowsazurebootcamp.com/whattobring Boot Camp Agenda Day 1 – July1st 2010:  · 8:30 – 9:00 - Registration · 9:00 – 10:00 - Module 1: Intro to Azure & Cloud Computing · 10:00 – 11:00 - Module 2: Using Web Roles · 11:00 – Noon - Lab 1 & workstation configuration · Noon – 1:00 - Lunch · 1:00 – 2:00 - Module 3: Blobs · 2:00 – 3:00 - Module 4: Tables · 3:00 – 4:00 - Module 5: Queues · 4:00 – ? - Q&A / Open Discussion Day 2 – July 2nd 2010: · 9:00 – 10:00 - Module 6: Building a business with Azure · 10:00 – 11:00 - Module 7: Cloud Scenarios · 11:00 – Noon - Module 8: SQL Azure · Noon – 1:00 - Lunch · 1:00 – 2:00 - Module 9: Basic Worker Roles · 2:00 – 3:00 - Module 10: Advanced Worker Roles · 3:00 – 4:00 - Module 11: Azure Diagnostics · 4:00 –    ??? - Module 12: App Fabric  

  Read the article

• Sixeyed.Caching available now on NuGet and GitHub!

  - by Elton Stoneman

  Originally posted on: http://geekswithblogs.net/EltonStoneman/archive/2013/10/22/sixeyed.caching-available-now-on-nuget-and-github.aspxThe good guys at Pluralsight have okayed me to publish my caching framework (as seen in Caching in the .NET Stack: Inside-Out) as an open-source library, and it’s out now. You can get it here: Sixeyed.Caching source code on GitHub, and here: Sixeyed.Caching package v1.0.0 on NuGet. If you haven’t seen the course, there’s a preview here on YouTube: In-Process and Out-of-Process Caches, which gives a good flavour. The library is a wrapper around various cache providers, including the .NET MemoryCache, AppFabric cache, and  memcached*. All the wrappers inherit from a base class which gives you a set of common functionality against all the cache implementations: •    inherits OutputCacheProvider, so you can use your chosen cache provider as an ASP.NET output cache; •    serialization and encryption, so you can configure whether you want your cache items serialized (XML, JSON or binary) and encrypted; •    instrumentation, you can optionally use performance counters to monitor cache attempts and hits, at a low level. The framework wraps up different caches into an ICache interface, and it lets you use a provider directly like this: Cache.Memory.Get<RefData>(refDataKey); - or with configuration to use the default cache provider: Cache.Default.Get<RefData>(refDataKey); The library uses Unity’s interception framework to implement AOP caching, which you can use by flagging methods with the [Cache] attribute: [Cache] public RefData GetItem(string refDataKey) - and you can be more specific on the required cache behaviour: [Cache(CacheType=CacheType.Memory, Days=1] public RefData GetItem(string refDataKey) - or really specific: [Cache(CacheType=CacheType.Disk, SerializationFormat=SerializationFormat.Json, Hours=2, Minutes=59)] public RefData GetItem(string refDataKey) Provided you get instances of classes with cacheable methods from the container, the attributed method results will be cached, and repeated calls will be fetched from the cache. You can also set a bunch of cache defaults in application config, like whether to use encryption and instrumentation, and whether the cache system is enabled at all: <sixeyed.caching enabled="true"> <performanceCounters instrumentCacheTotalCounts="true" instrumentCacheTargetCounts="true" categoryNamePrefix ="Sixeyed.Caching.Tests"/> <encryption enabled="true" key="1234567890abcdef1234567890abcdef" iv="1234567890abcdef"/> <!-- key must be 32 characters, IV must be 16 characters--> </sixeyed.caching> For AOP and methods flagged with the cache attribute, you can override the compile-time cache settings at runtime with more config (keyed by the class and method name): <sixeyed.caching enabled="true"> <targets> <target keyPrefix="MethodLevelCachingStub.GetRandomIntCacheConfiguredInternal" enabled="false"/> <target keyPrefix="MethodLevelCachingStub.GetRandomIntCacheExpiresConfiguredInternal" seconds="1"/> </targets> It’s released under the MIT license, so you can use it freely in your own apps and modify as required. I’ll be adding more content to the GitHub wiki, which will be the main source of documentation, but for now there’s an FAQ to get you started. * - in the course the framework library also wraps NCache Express, but there's no public redistributable library that I can find, so it's not in Sixeyed.Caching.

  Read the article

• What’s new in Silverlight 4 RC?

  - by pluginbaby

  I am here in Las Vegas for MIX10 where Scott Guthrie announced today the release of Silverlight 4 RC and the Visual Studio 2010 tools. You can now install VS2010 RC!!! As always, downloads links are here: www.silverlight.net He also said that the final version of Silverlight 4 will come next month (so april)! 4 months ago, I wrote a blog post on the new features of Silverlight 4 beta, so… what’s new in the RC ?   Rich Text · RichTextArea renamed to RichTextBox · Text position and selection APIs · “Xaml” property for serializing text content · XAML clipboard format · FlowDirection support on Runs tag · “Format then type” support when dragging controls to the designer · Thai/Vietnamese/Indic support · UI Automation Text pattern   Networking · UploadProgress support (Client stack) · Caching support (Client stack) · Sockets security restrictions removal (Elevated Trust) · Sockets policy file retrieval via HTTP · Accept-Language header   Out of Browser (Elevated Trust) · XAP signing · Silent install and emulation mode · Custom window chrome · Better support for COM Automation · Cancellable shutdown event · Updated security dialogs   Media · Pinned full-screen mode on secondary display · Webcam/Mic configuration preview · More descriptive MediaSourceStream errors · Content & Output protection updates · Updates to H.264 content protection (ClearNAL) · Digital Constraint Token · CGMS-A · Multicast · Graphics card driver validation & revocation   Graphics and Printing · HW accelerated Perspective Transforms · Ability to query page size and printable area · Memory usage and perf improvements   Data · Entity-level validation support of INotifyDataErrorInfo for DataGrid · XPath support for XML   Parser · New architecture enables future innovation · Performance and stability improvements · XmlnsPrefix & XmlnsDefinition attributes · Support setting order-dependent properties   Globalization & Localization · Support for 31 new languages · Arabic, Hebrew and Thai input on Mac · Indic support   More … · Update to DeepZoom code base with HW acceleration · Support for Private mode browsing · Google Chrome support (Windows) · FrameworkElement.Unloaded event · HTML Hosting accessibility · IsoStore perf improvements · Native hosting perf improvements (e.g., Bing Toolbar) · Consistency with Silverlight for Mobile APIs and Tooling · SDK   - System.Numerics.dll   - Dynamic XAP support (MEF)   - Frame/Navigation refresh support   That’s a lot!   You will find more details on the following links: http://timheuer.com/blog/archive/2010/03/15/whats-new-in-silverlight-4-rc-mix10.aspx http://www.davidpoll.com/2010/03/15/new-in-the-silverlight-4-rc-xaml-features/   Technorati Tags: Silverlight

  Read the article

• Fed Authentication Methods in OIF / IdP

  - by Damien Carru

  This article is a continuation of my previous entry where I explained how OIF/IdP leverages OAM to authenticate users at runtime: OIF/IdP internally forwards the user to OAM and indicates which Authentication Scheme should be used to challenge the user if needed OAM determine if the user should be challenged (user already authenticated, session timed out or not, session authentication level equal or higher than the level of the authentication scheme specified by OIF/IdP…) After identifying the user, OAM internally forwards the user back to OIF/IdP OIF/IdP can resume its operation In this article, I will discuss how OIF/IdP can be configured to map Federation Authentication Methods to OAM Authentication Schemes: When processing an Authn Request, where the SP requests a specific Federation Authentication Method with which the user should be challenged When sending an Assertion, where OIF/IdP sets the Federation Authentication Method in the Assertion Enjoy the reading! Overview The various Federation protocols support mechanisms allowing the partners to exchange information on: How the user should be challenged, when the SP/RP makes a request How the user was challenged, when the IdP/OP issues an SSO response When a remote SP partner redirects the user to OIF/IdP for Federation SSO, the message might contain data requesting how the user should be challenged by the IdP: this is treated as the Requested Federation Authentication Method. OIF/IdP will need to map that Requested Federation Authentication Method to a local Authentication Scheme, and then invoke OAM for user authentication/challenge with the mapped Authentication Scheme. OAM would authenticate the user if necessary with the scheme specified by OIF/IdP. Similarly, when an IdP issues an SSO response, most of the time it will need to include an identifier representing how the user was challenged: this is treated as the Federation Authentication Method. When OIF/IdP issues an Assertion, it will evaluate the Authentication Scheme with which OAM identified the user: If the Authentication Scheme can be mapped to a Federation Authentication Method, then OIF/IdP will use the result of that mapping in the outgoing SSO response: AuthenticationStatement in the SAML Assertion OpenID Response, if PAPE is enabled If the Authentication Scheme cannot be mapped, then OIF/IdP will set the Federation Authentication Method as the Authentication Scheme name in the outgoing SSO response: AuthenticationStatement in the SAML Assertion OpenID Response, if PAPE is enabled Mappings In OIF/IdP, the mapping between Federation Authentication Methods and Authentication Schemes has the following rules: One Federation Authentication Method can be mapped to several Authentication Schemes In a Federation Authentication Method <-> Authentication Schemes mapping, a single Authentication Scheme is marked as the default scheme that will be used to authenticate a user, if the SP/RP partner requests the user to be authenticated via a specific Federation Authentication Method An Authentication Scheme can be mapped to a single Federation Authentication Method Let’s examine the following example and the various use cases, based on the SAML 2.0 protocol: Mappings defined as: urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport mapped to LDAPScheme, marked as the default scheme used for authentication BasicScheme urn:oasis:names:tc:SAML:2.0:ac:classes:X509 mapped to X509Scheme, marked as the default scheme used for authentication Use cases: SP sends an AuthnRequest specifying urn:oasis:names:tc:SAML:2.0:ac:classes:X509 as the RequestedAuthnContext: OIF/IdP will authenticate the use with X509Scheme since it is the default scheme mapped for that method. SP sends an AuthnRequest specifying urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport as the RequestedAuthnContext: OIF/IdP will authenticate the use with LDAPScheme since it is the default scheme mapped for that method, not the BasicScheme SP did not request any specific methods, and user was authenticated with BasisScheme: OIF/IdP will issue an Assertion with urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport as the FederationAuthenticationMethod SP did not request any specific methods, and user was authenticated with LDAPScheme: OIF/IdP will issue an Assertion with urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport as the FederationAuthenticationMethod SP did not request any specific methods, and user was authenticated with BasisSessionlessScheme: OIF/IdP will issue an Assertion with BasisSessionlessScheme as the FederationAuthenticationMethod, since that scheme could not be mapped to any Federation Authentication Method (in this case, the administrator would need to correct that and create a mapping) Configuration Mapping Federation Authentication Methods to OAM Authentication Schemes is protocol dependent, since the methods are defined in the various protocols (SAML 2.0, SAML 1.1, OpenID 2.0). As such, the WLST commands to set those mappings will involve: Either the SP Partner Profile and affect all Partners referencing that profile, which do not override the Federation Authentication Method to OAM Authentication Scheme mappings Or the SP Partner entry, which will only affect the SP Partner It is important to note that if an SP Partner is configured to define one or more Federation Authentication Method to OAM Authentication Scheme mappings, then all the mappings defined in the SP Partner Profile will be ignored. Authentication Schemes As discussed in the previous article, during Federation SSO, OIF/IdP will internally forward the user to OAM for authentication/verification and specify which Authentication Scheme to use. OAM will determine if a user needs to be challenged: If the user is not authenticated yet If the user is authenticated but the session timed out If the user is authenticated, but the authentication scheme level of the original authentication is lower than the level of the authentication scheme requested by OIF/IdP So even though an SP requests a specific Federation Authentication Method to be used to challenge the user, if that method is mapped to an Authentication Scheme and that at runtime OAM deems that the user does not need to be challenged with that scheme (because the user is already authenticated, session did not time out, and the session authn level is equal or higher than the one for the specified Authentication Scheme), the flow won’t result in a challenge operation. Protocols SAML 2.0 The SAML 2.0 specifications define the following Federation Authentication Methods for SAML 2.0 flows: urn:oasis:names:tc:SAML:2.0:ac:classes:unspecified urn:oasis:names:tc:SAML:2.0:ac:classes:InternetProtocol urn:oasis:names:tc:SAML:2.0:ac:classes:Telephony urn:oasis:names:tc:SAML:2.0:ac:classes:MobileOneFactorUnregistered urn:oasis:names:tc:SAML:2.0:ac:classes:PersonalTelephony urn:oasis:names:tc:SAML:2.0:ac:classes:PreviousSession urn:oasis:names:tc:SAML:2.0:ac:classes:MobileOneFactorContract urn:oasis:names:tc:SAML:2.0:ac:classes:Smartcard urn:oasis:names:tc:SAML:2.0:ac:classes:Password urn:oasis:names:tc:SAML:2.0:ac:classes:InternetProtocolPassword urn:oasis:names:tc:SAML:2.0:ac:classes:X509 urn:oasis:names:tc:SAML:2.0:ac:classes:TLSClient urn:oasis:names:tc:SAML:2.0:ac:classes:PGP urn:oasis:names:tc:SAML:2.0:ac:classes:SPKI urn:oasis:names:tc:SAML:2.0:ac:classes:XMLDSig urn:oasis:names:tc:SAML:2.0:ac:classes:SoftwarePKI urn:oasis:names:tc:SAML:2.0:ac:classes:Kerberos urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport urn:oasis:names:tc:SAML:2.0:ac:classes:SecureRemotePassword urn:oasis:names:tc:SAML:2.0:ac:classes:NomadTelephony urn:oasis:names:tc:SAML:2.0:ac:classes:AuthenticatedTelephony urn:oasis:names:tc:SAML:2.0:ac:classes:MobileTwoFactorUnregistered urn:oasis:names:tc:SAML:2.0:ac:classes:MobileTwoFactorContract urn:oasis:names:tc:SAML:2.0:ac:classes:SmartcardPKI urn:oasis:names:tc:SAML:2.0:ac:classes:TimeSyncToken Out of the box, OIF/IdP has the following mappings for the SAML 2.0 protocol: Only urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport is defined This Federation Authentication Method is mapped to: LDAPScheme, marked as the default scheme used for authentication FAAuthScheme BasicScheme BasicFAScheme This mapping is defined in the saml20-sp-partner-profile SP Partner Profile which is the default OOTB SP Partner Profile for SAML 2.0 An example of an AuthnRequest message sent by an SP to an IdP with the SP requesting a specific Federation Authentication Method to be used to challenge the user would be: <samlp:AuthnRequest xmlns:samlp="urn:oasis:names:tc:SAML:2.0:protocol" Destination="https://idp.com/oamfed/idp/samlv20" ID="id-8bWn-A9o4aoMl3Nhx1DuPOOjawc-" IssueInstant="2014-03-21T20:51:11Z" Version="2.0">  <saml:Issuer ...>https://acme.com/sp</saml:Issuer>  <samlp:NameIDPolicy AllowCreate="false" Format="urn:oasis:names:tc:SAML:1.1:nameid-format:unspecified"/>  <samlp:RequestedAuthnContext Comparison="minimum">    <saml:AuthnContextClassRef xmlns:saml="urn:oasis:names:tc:SAML:2.0:assertion">      urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport </saml:AuthnContextClassRef>  </samlp:RequestedAuthnContext></samlp:AuthnRequest> An example of an Assertion issued by an IdP would be: <samlp:Response ...>    <saml:Issuer ...>https://idp.com/oam/fed</saml:Issuer>    <samlp:Status>        <samlp:StatusCode Value="urn:oasis:names:tc:SAML:2.0:status:Success"/>    </samlp:Status>    <saml:Assertion ...>        <saml:Issuer ...>https://idp.com/oam/fed</saml:Issuer>        <dsig:Signature>            ...        </dsig:Signature>        <saml:Subject>            <saml:NameID ...>[email protected]</saml:NameID>            <saml:SubjectConfirmation Method="urn:oasis:names:tc:SAML:2.0:cm:bearer">                <saml:SubjectConfirmationData .../>            </saml:SubjectConfirmation>        </saml:Subject>        <saml:Conditions ...>            <saml:AudienceRestriction>                <saml:Audience>https://acme.com/sp</saml:Audience>            </saml:AudienceRestriction>        </saml:Conditions>        <saml:AuthnStatement AuthnInstant="2014-03-21T20:53:55Z" SessionIndex="id-6i-Dm0yB-HekG6cejktwcKIFMzYE8Yrmqwfd0azz" SessionNotOnOrAfter="2014-03-21T21:53:55Z">            <saml:AuthnContext>                <saml:AuthnContextClassRef>                    urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport                </saml:AuthnContextClassRef>            </saml:AuthnContext>        </saml:AuthnStatement>    </saml:Assertion></samlp:Response> An administrator would be able to specify a mapping between a SAML 2.0 Federation Authentication Method and one or more OAM Authentication Schemes SAML 1.1 The SAML 1.1 specifications define the following Federation Authentication Methods for SAML 1.1 flows: urn:oasis:names:tc:SAML:1.0:am:unspecified urn:oasis:names:tc:SAML:1.0:am:HardwareToken urn:oasis:names:tc:SAML:1.0:am:password urn:oasis:names:tc:SAML:1.0:am:X509-PKI urn:ietf:rfc:2246 urn:oasis:names:tc:SAML:1.0:am:PGP urn:oasis:names:tc:SAML:1.0:am:SPKI urn:ietf:rfc:3075 urn:oasis:names:tc:SAML:1.0:am:XKMS urn:ietf:rfc:1510 urn:ietf:rfc:2945 Out of the box, OIF/IdP has the following mappings for the SAML 1.1 protocol: Only urn:oasis:names:tc:SAML:1.0:am:password is defined This Federation Authentication Method is mapped to: LDAPScheme, marked as the default scheme used for authentication FAAuthScheme BasicScheme BasicFAScheme This mapping is defined in the saml11-sp-partner-profile SP Partner Profile which is the default OOTB SP Partner Profile for SAML 1.1 An example of an Assertion issued by an IdP would be: <samlp:Response ...>    <samlp:Status>        <samlp:StatusCode Value="samlp:Success"/>    </samlp:Status>    <saml:Assertion Issuer="https://idp.com/oam/fed" ...>        <saml:Conditions ...>            <saml:AudienceRestriction>                <saml:Audience>https://acme.com/sp/ssov11</saml:Audience>            </saml:AudienceRestriction>        </saml:Conditions>        <saml:AuthnStatement AuthenticationInstant="2014-03-21T20:53:55Z" AuthenticationMethod="urn:oasis:names:tc:SAML:1.0:am:password">            <saml:Subject>                <saml:NameID ...>[email protected]</saml:NameID>                <saml:SubjectConfirmation>                   <saml:ConfirmationMethod>                       urn:oasis:names:tc:SAML:1.0:cm:bearer                   </saml:ConfirmationMethod>                </saml:SubjectConfirmation>            </saml:Subject>        </saml:AuthnStatement>        <dsig:Signature>            ...        </dsig:Signature>    </saml:Assertion></samlp:Response> Note: SAML 1.1 does not define an AuthnRequest message. An administrator would be able to specify a mapping between a SAML 1.1 Federation Authentication Method and one or more OAM Authentication Schemes OpenID 2.0 The OpenID 2.0 PAPE specifications define the following Federation Authentication Methods for OpenID 2.0 flows: http://schemas.openid.net/pape/policies/2007/06/phishing-resistant http://schemas.openid.net/pape/policies/2007/06/multi-factor http://schemas.openid.net/pape/policies/2007/06/multi-factor-physical Out of the box, OIF/IdP does not define any mappings for the OpenID 2.0 Federation Authentication Methods. For OpenID 2.0, the configuration will involve mapping a list of OpenID 2.0 policies to a list of Authentication Schemes. An example of an OpenID 2.0 Request message sent by an SP/RP to an IdP/OP would be: https://idp.com/openid?openid.ns=http%3A%2F%2Fspecs.openid.net%2Fauth%2F2.0&openid.mode=checkid_setup&openid.claimed_id=http%3A%2F%2Fspecs.openid.net%2Fauth%2F2.0%2Fidentifier_select&openid.identity=http%3A%2F%2Fspecs.openid.net%2Fauth%2F2.0%2Fidentifier_select&openid.assoc_handle=id-6a5S6zhAKaRwQNUnjTKROREdAGSjWodG1el4xyz3&openid.return_to=https%3A%2F%2Facme.com%2Fopenid%3Frefid%3Did-9PKVXZmRxAeDYcgLqPm36ClzOMA-&openid.realm=https%3A%2F%2Facme.com%2Fopenid&openid.ns.ax=http%3A%2F%2Fopenid.net%2Fsrv%2Fax%2F1.0&openid.ax.mode=fetch_request&openid.ax.type.attr0=http%3A%2F%2Faxschema.org%2Fcontact%2Femail&openid.ax.if_available=attr0&openid.ns.pape=http%3A%2F%2Fspecs.openid.net%2Fextensions%2Fpape%2F1.0&openid.pape.max_auth_age=0 An example of an Open ID 2.0 SSO Response issued by an IdP/OP would be: https://acme.com/openid?refid=id-9PKVXZmRxAeDYcgLqPm36ClzOMA-&openid.ns=http%3A%2F%2Fspecs.openid.net%2Fauth%2F2.0&openid.mode=id_res&openid.op_endpoint=https%3A%2F%2Fidp.com%2Fopenid&openid.claimed_id=https%3A%2F%2Fidp.com%2Fopenid%3Fid%3Did-38iCmmlAVEXPsFjnFVKArfn5RIiF75D5doorhEgqqPM%3D&openid.identity=https%3A%2F%2Fidp.com%2Fopenid%3Fid%3Did-38iCmmlAVEXPsFjnFVKArfn5RIiF75D5doorhEgqqPM%3D&openid.return_to=https%3A%2F%2Facme.com%2Fopenid%3Frefid%3Did-9PKVXZmRxAeDYcgLqPm36ClzOMA-&openid.response_nonce=2014-03-24T19%3A20%3A06Zid-YPa2kTNNFftZkgBb460jxJGblk2g--iNwPpDI7M1&openid.assoc_handle=id-6a5S6zhAKaRwQNUnjTKROREdAGSjWodG1el4xyz3&openid.ns.ax=http%3A%2F%2Fopenid.net%2Fsrv%2Fax%2F1.0&openid.ax.mode=fetch_response&openid.ax.type.attr0=http%3A%2F%2Fsession%2Fcount&openid.ax.value.attr0=1&openid.ax.type.attr1=http%3A%2F%2Fopenid.net%2Fschema%2FnamePerson%2Ffriendly&openid.ax.value.attr1=My+name+is+Bobby+Smith&openid.ax.type.attr2=http%3A%2F%2Fschemas.openid.net%2Fax%2Fapi%2Fuser_id&openid.ax.value.attr2=bob&openid.ax.type.attr3=http%3A%2F%2Faxschema.org%2Fcontact%2Femail&openid.ax.value.attr3=bob%40oracle.com&openid.ax.type.attr4=http%3A%2F%2Fsession%2Fipaddress&openid.ax.value.attr4=10.145.120.253&openid.ns.pape=http%3A%2F%2Fspecs.openid.net%2Fextensions%2Fpape%2F1.0&openid.pape.auth_time=2014-03-24T19%3A20%3A05Z&openid.pape.auth_policies=http%3A%2F%2Fschemas.openid.net%2Fpape%2Fpolicies%2F2007%2F06%2Fphishing-resistant&openid.signed=op_endpoint%2Cclaimed_id%2Cidentity%2Creturn_to%2Cresponse_nonce%2Cassoc_handle%2Cns.ax%2Cax.mode%2Cax.type.attr0%2Cax.value.attr0%2Cax.type.attr1%2Cax.value.attr1%2Cax.type.attr2%2Cax.value.attr2%2Cax.type.attr3%2Cax.value.attr3%2Cax.type.attr4%2Cax.value.attr4%2Cns.pape%2Cpape.auth_time%2Cpape.auth_policies&openid.sig=mYMgbGYSs22l8e%2FDom9NRPw15u8%3D In the next article, I will provide examples on how to configure OIF/IdP for the various protocols, to map OAM Authentication Schemes to Federation Authentication Methods.Cheers,Damien Carru

  Read the article

• Vidalia detected that the Tor software exited unexpectedly?

  - by Rana Muhammad Waqas

  I have installed the vidalia by following these instructions everything went as they mentioned. When I started vidalia it gave me the error: Vidalia was unable to start Tor. Check your settings to ensure the correct name and location of your Tor executable is specified. I found that bug here and followed their instructions to fix it and now after that it says: Vidalia detected that the Tor software exited unexpectedly. Please check the message log for recent warning or error messages. Logs of Vidalia Oct 18 02:15:06.937 [Notice] Tor v0.2.3.25 (git-3fed5eb096d2d187) running on Linux. Oct 18 02:15:06.937 [Notice] Tor can't help you if you use it wrong! Learn how to be safe at https://www.torproject.org/download/download#warning Oct 18 02:15:06.937 [Notice] Read configuration file "/home/waqas/.vidalia/torrc". Oct 18 02:15:06.937 [Notice] We were compiled with headers from version 2.0.19-stable of Libevent, but we're using a Libevent library that says it's version 2.0.21-stable. Oct 18 02:15:06.938 [Notice] Initialized libevent version 2.0.21-stable using method epoll (with changelist). Good. Oct 18 02:15:06.938 [Notice] Opening Socks listener on 127.0.0.1:9050 Oct 18 02:15:06.938 [Warning] Could not bind to 127.0.0.1:9050: Address already in use. Is Tor already running? Oct 18 02:15:06.938 [Warning] /var/run/tor is not owned by this user (waqas, 1000) but by debian-tor (118). Perhaps you are running Tor as the wrong user? Oct 18 02:15:06.938 [Warning] Before Tor can create a control socket in "/var/run/tor/control", the directory "/var/run/tor" needs to exist, and to be accessible only by the user account that is running Tor. (On some Unix systems, anybody who can list a socket can connect to it, so Tor is being careful.) Oct 18 02:15:06.938 [Warning] Failed to parse/validate config: Failed to bind one of the listener ports. Oct 18 02:15:06.938 [Error] Reading config failed--see warnings above. Please Help !

  Read the article

• High CPU usage with Team Speak 3.0.0-rc2

  - by AlexTheBird

  The CPU usage is always around 40 percent. I use push-to-talk and I had uninstalled pulseaudio. Now I use Alsa. I don't even have to connect to a Server. By simply starting TS the cpu usage goes up 40 percent and stays there. The CPU usage of 3.0.0-rc1 [Build: 14468] is constantly 14 percent. This is the output of top, mpstat and ps aux while I am running TS3 ... of course: alexandros@alexandros-laptop:~$ top top - 18:20:07 up 2:22, 3 users, load average: 1.02, 0.85, 0.77 Tasks: 163 total, 1 running, 162 sleeping, 0 stopped, 0 zombie Cpu(s): 5.3%us, 1.9%sy, 0.1%ni, 91.8%id, 0.7%wa, 0.1%hi, 0.1%si, 0.0%st Mem: 2061344k total, 964028k used, 1097316k free, 69116k buffers Swap: 3997688k total, 0k used, 3997688k free, 449032k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2714 alexandr 20 0 206m 31m 24m S 37 1.6 0:12.78 ts3client_linux 868 root 20 0 47564 27m 10m S 8 1.4 3:21.73 Xorg 1 root 20 0 2804 1660 1204 S 0 0.1 0:00.53 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root RT 0 0 0 0 S 0 0.0 0:00.01 migration/0 4 root 20 0 0 0 0 S 0 0.0 0:00.45 ksoftirqd/0 5 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 6 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/1 7 root 20 0 0 0 0 S 0 0.0 0:00.08 ksoftirqd/1 8 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/1 9 root 20 0 0 0 0 S 0 0.0 0:01.17 events/0 10 root 20 0 0 0 0 S 0 0.0 0:00.81 events/1 11 root 20 0 0 0 0 S 0 0.0 0:00.00 cpuset 12 root 20 0 0 0 0 S 0 0.0 0:00.00 khelper 13 root 20 0 0 0 0 S 0 0.0 0:00.00 async/mgr 14 root 20 0 0 0 0 S 0 0.0 0:00.00 pm 16 root 20 0 0 0 0 S 0 0.0 0:00.00 sync_supers 17 root 20 0 0 0 0 S 0 0.0 0:00.00 bdi-default 18 root 20 0 0 0 0 S 0 0.0 0:00.00 kintegrityd/0 19 root 20 0 0 0 0 S 0 0.0 0:00.00 kintegrityd/1 20 root 20 0 0 0 0 S 0 0.0 0:00.05 kblockd/0 21 root 20 0 0 0 0 S 0 0.0 0:00.02 kblockd/1 22 root 20 0 0 0 0 S 0 0.0 0:00.00 kacpid 23 root 20 0 0 0 0 S 0 0.0 0:00.00 kacpi_notify 24 root 20 0 0 0 0 S 0 0.0 0:00.00 kacpi_hotplug 25 root 20 0 0 0 0 S 0 0.0 0:00.99 ata/0 26 root 20 0 0 0 0 S 0 0.0 0:00.92 ata/1 27 root 20 0 0 0 0 S 0 0.0 0:00.00 ata_aux 28 root 20 0 0 0 0 S 0 0.0 0:00.00 ksuspend_usbd 29 root 20 0 0 0 0 S 0 0.0 0:00.00 khubd alexandros@alexandros-laptop:~$ mpstat Linux 2.6.32-32-generic (alexandros-laptop) 16.06.2011 _i686_ (2 CPU) 18:20:15 CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle 18:20:15 all 5,36 0,09 1,91 0,68 0,07 0,06 0,00 0,00 91,83 alexandros@alexandros-laptop:~$ ps aux USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 1 0.0 0.0 2804 1660 ? Ss 15:58 0:00 /sbin/init root 2 0.0 0.0 0 0 ? S 15:58 0:00 [kthreadd] root 3 0.0 0.0 0 0 ? S 15:58 0:00 [migration/0] root 4 0.0 0.0 0 0 ? S 15:58 0:00 [ksoftirqd/0] root 5 0.0 0.0 0 0 ? S 15:58 0:00 [watchdog/0] root 6 0.0 0.0 0 0 ? S 15:58 0:00 [migration/1] root 7 0.0 0.0 0 0 ? S 15:58 0:00 [ksoftirqd/1] root 8 0.0 0.0 0 0 ? S 15:58 0:00 [watchdog/1] root 9 0.0 0.0 0 0 ? S 15:58 0:01 [events/0] root 10 0.0 0.0 0 0 ? S 15:58 0:00 [events/1] root 11 0.0 0.0 0 0 ? S 15:58 0:00 [cpuset] root 12 0.0 0.0 0 0 ? S 15:58 0:00 [khelper] root 13 0.0 0.0 0 0 ? S 15:58 0:00 [async/mgr] root 14 0.0 0.0 0 0 ? S 15:58 0:00 [pm] root 16 0.0 0.0 0 0 ? S 15:58 0:00 [sync_supers] root 17 0.0 0.0 0 0 ? S 15:58 0:00 [bdi-default] root 18 0.0 0.0 0 0 ? S 15:58 0:00 [kintegrityd/0] root 19 0.0 0.0 0 0 ? S 15:58 0:00 [kintegrityd/1] root 20 0.0 0.0 0 0 ? S 15:58 0:00 [kblockd/0] root 21 0.0 0.0 0 0 ? S 15:58 0:00 [kblockd/1] root 22 0.0 0.0 0 0 ? S 15:58 0:00 [kacpid] root 23 0.0 0.0 0 0 ? S 15:58 0:00 [kacpi_notify] root 24 0.0 0.0 0 0 ? S 15:58 0:00 [kacpi_hotplug] root 25 0.0 0.0 0 0 ? S 15:58 0:00 [ata/0] root 26 0.0 0.0 0 0 ? S 15:58 0:00 [ata/1] root 27 0.0 0.0 0 0 ? S 15:58 0:00 [ata_aux] root 28 0.0 0.0 0 0 ? S 15:58 0:00 [ksuspend_usbd] root 29 0.0 0.0 0 0 ? S 15:58 0:00 [khubd] root 30 0.0 0.0 0 0 ? S 15:58 0:00 [kseriod] root 31 0.0 0.0 0 0 ? S 15:58 0:00 [kmmcd] root 34 0.0 0.0 0 0 ? S 15:58 0:00 [khungtaskd] root 35 0.0 0.0 0 0 ? S 15:58 0:00 [kswapd0] root 36 0.0 0.0 0 0 ? SN 15:58 0:00 [ksmd] root 37 0.0 0.0 0 0 ? S 15:58 0:00 [aio/0] root 38 0.0 0.0 0 0 ? S 15:58 0:00 [aio/1] root 39 0.0 0.0 0 0 ? S 15:58 0:00 [ecryptfs-kthrea] root 40 0.0 0.0 0 0 ? S 15:58 0:00 [crypto/0] root 41 0.0 0.0 0 0 ? S 15:58 0:00 [crypto/1] root 48 0.0 0.0 0 0 ? S 15:58 0:03 [scsi_eh_0] root 50 0.0 0.0 0 0 ? S 15:58 0:00 [scsi_eh_1] root 53 0.0 0.0 0 0 ? S 15:58 0:00 [kstriped] root 54 0.0 0.0 0 0 ? S 15:58 0:00 [kmpathd/0] root 55 0.0 0.0 0 0 ? S 15:58 0:00 [kmpathd/1] root 56 0.0 0.0 0 0 ? S 15:58 0:00 [kmpath_handlerd] root 57 0.0 0.0 0 0 ? S 15:58 0:00 [ksnapd] root 58 0.0 0.0 0 0 ? S 15:58 0:03 [kondemand/0] root 59 0.0 0.0 0 0 ? S 15:58 0:02 [kondemand/1] root 60 0.0 0.0 0 0 ? S 15:58 0:00 [kconservative/0] root 61 0.0 0.0 0 0 ? S 15:58 0:00 [kconservative/1] root 213 0.0 0.0 0 0 ? S 15:58 0:00 [scsi_eh_2] root 222 0.0 0.0 0 0 ? S 15:58 0:00 [scsi_eh_3] root 234 0.0 0.0 0 0 ? S 15:58 0:00 [scsi_eh_4] root 235 0.0 0.0 0 0 ? S 15:58 0:01 [usb-storage] root 255 0.0 0.0 0 0 ? S 15:58 0:00 [jbd2/sda5-8] root 256 0.0 0.0 0 0 ? S 15:58 0:00 [ext4-dio-unwrit] root 257 0.0 0.0 0 0 ? S 15:58 0:00 [ext4-dio-unwrit] root 290 0.0 0.0 0 0 ? S 15:58 0:00 [flush-8:0] root 318 0.0 0.0 2316 888 ? S 15:58 0:00 upstart-udev-bridge --daemon root 321 0.0 0.0 2616 1024 ? S<s 15:58 0:00 udevd --daemon root 526 0.0 0.0 0 0 ? S 15:58 0:00 [kpsmoused] root 528 0.0 0.0 0 0 ? S 15:58 0:00 [led_workqueue] root 650 0.0 0.0 0 0 ? S 15:58 0:00 [radeon/0] root 651 0.0 0.0 0 0 ? S 15:58 0:00 [radeon/1] root 652 0.0 0.0 0 0 ? S 15:58 0:00 [ttm_swap] root 654 0.0 0.0 2612 984 ? S< 15:58 0:00 udevd --daemon root 656 0.0 0.0 0 0 ? S 15:58 0:00 [hd-audio0] root 657 0.0 0.0 2612 916 ? S< 15:58 0:00 udevd --daemon root 674 0.6 0.0 0 0 ? S 15:58 0:57 [phy0] syslog 715 0.0 0.0 34812 1776 ? Sl 15:58 0:00 rsyslogd -c4 102 731 0.0 0.0 3236 1512 ? Ss 15:58 0:02 dbus-daemon --system --fork root 740 0.0 0.1 19088 3380 ? Ssl 15:58 0:00 gdm-binary root 744 0.0 0.1 18900 4032 ? Ssl 15:58 0:01 NetworkManager avahi 749 0.0 0.0 2928 1520 ? S 15:58 0:00 avahi-daemon: running [alexandros-laptop.local] avahi 752 0.0 0.0 2928 544 ? Ss 15:58 0:00 avahi-daemon: chroot helper root 753 0.0 0.1 4172 2300 ? S 15:58 0:00 /usr/sbin/modem-manager root 762 0.0 0.1 20584 3152 ? Sl 15:58 0:00 /usr/sbin/console-kit-daemon --no-daemon root 836 0.0 0.1 20856 3864 ? Sl 15:58 0:00 /usr/lib/gdm/gdm-simple-slave --display-id /org/gnome/DisplayManager/Display1 root 856 0.0 0.1 4836 2388 ? S 15:58 0:00 /sbin/wpa_supplicant -u -s root 868 2.3 1.3 36932 27924 tty7 Rs+ 15:58 3:22 /usr/bin/X :0 -nr -verbose -auth /var/run/gdm/auth-for-gdm-a46T4j/database -nolisten root 891 0.0 0.0 1792 564 tty4 Ss+ 15:58 0:00 /sbin/getty -8 38400 tty4 root 901 0.0 0.0 1792 564 tty5 Ss+ 15:58 0:00 /sbin/getty -8 38400 tty5 root 908 0.0 0.0 1792 564 tty2 Ss+ 15:58 0:00 /sbin/getty -8 38400 tty2 root 910 0.0 0.0 1792 568 tty3 Ss+ 15:58 0:00 /sbin/getty -8 38400 tty3 root 913 0.0 0.0 1792 564 tty6 Ss+ 15:58 0:00 /sbin/getty -8 38400 tty6 root 917 0.0 0.0 2180 1072 ? Ss 15:58 0:00 acpid -c /etc/acpi/events -s /var/run/acpid.socket daemon 924 0.0 0.0 2248 432 ? Ss 15:58 0:00 atd root 927 0.0 0.0 2376 900 ? Ss 15:58 0:00 cron root 950 0.0 0.0 11736 1372 ? Ss 15:58 0:00 /usr/sbin/winbindd root 958 0.0 0.0 11736 1184 ? S 15:58 0:00 /usr/sbin/winbindd root 974 0.0 0.1 6832 2580 ? Ss 15:58 0:00 /usr/sbin/cupsd -C /etc/cups/cupsd.conf root 1078 0.0 0.0 1792 564 tty1 Ss+ 15:58 0:00 /sbin/getty -8 38400 tty1 gdm 1097 0.0 0.0 3392 772 ? S 15:58 0:00 /usr/bin/dbus-launch --exit-with-session root 1112 0.0 0.1 19216 3292 ? Sl 15:58 0:00 /usr/lib/gdm/gdm-session-worker root 1116 0.0 0.1 5540 2932 ? S 15:58 0:01 /usr/lib/upower/upowerd root 1131 0.0 0.1 6308 3824 ? S 15:58 0:00 /usr/lib/policykit-1/polkitd 108 1163 0.0 0.2 16788 4360 ? Ssl 15:58 0:01 /usr/sbin/hald root 1164 0.0 0.0 3536 1300 ? S 15:58 0:00 hald-runner root 1188 0.0 0.0 3612 1256 ? S 15:58 0:00 hald-addon-input: Listening on /dev/input/event6 /dev/input/event5 /dev/input/event2 root 1194 0.0 0.0 3612 1224 ? S 15:58 0:00 /usr/lib/hal/hald-addon-rfkill-killswitch root 1200 0.0 0.0 3608 1240 ? S 15:58 0:00 /usr/lib/hal/hald-addon-generic-backlight root 1202 0.0 0.0 3616 1236 ? S 15:58 0:02 hald-addon-storage: polling /dev/sr0 (every 2 sec) root 1204 0.0 0.0 3616 1236 ? S 15:58 0:00 hald-addon-storage: polling /dev/sdb (every 2 sec) root 1211 0.0 0.0 3624 1220 ? S 15:58 0:00 /usr/lib/hal/hald-addon-cpufreq 108 1212 0.0 0.0 3420 1200 ? S 15:58 0:00 hald-addon-acpi: listening on acpid socket /var/run/acpid.socket 1000 1222 0.0 0.1 24196 2816 ? Sl 15:58 0:00 /usr/bin/gnome-keyring-daemon --daemonize --login 1000 1240 0.0 0.3 28228 7312 ? Ssl 15:58 0:00 gnome-session 1000 1274 0.0 0.0 3284 356 ? Ss 15:58 0:00 /usr/bin/ssh-agent /usr/bin/dbus-launch --exit-with-session gnome-session 1000 1277 0.0 0.0 3392 772 ? S 15:58 0:00 /usr/bin/dbus-launch --exit-with-session gnome-session 1000 1278 0.0 0.0 3160 1652 ? Ss 15:58 0:00 /bin/dbus-daemon --fork --print-pid 5 --print-address 7 --session 1000 1281 0.0 0.2 8172 4636 ? S 15:58 0:00 /usr/lib/libgconf2-4/gconfd-2 1000 1287 0.0 0.5 24228 10896 ? Ss 15:58 0:03 /usr/lib/gnome-settings-daemon/gnome-settings-daemon 1000 1290 0.0 0.1 6468 2364 ? S 15:58 0:00 /usr/lib/gvfs/gvfsd 1000 1293 0.0 0.6 38104 13004 ? S 15:58 0:03 metacity 1000 1296 0.0 0.1 30280 2628 ? Ssl 15:58 0:00 /usr/lib/gvfs//gvfs-fuse-daemon /home/alexandros/.gvfs 1000 1301 0.0 0.0 3344 988 ? S 15:58 0:03 syndaemon -i 0.5 -k 1000 1303 0.0 0.1 8060 3488 ? S 15:58 0:00 /usr/lib/gvfs/gvfs-gdu-volume-monitor root 1306 0.0 0.1 15692 3104 ? Sl 15:58 0:00 /usr/lib/udisks/udisks-daemon 1000 1307 0.4 1.0 50748 21684 ? S 15:58 0:34 python -u /usr/share/screenlets/DigiClock/DigiClockScreenlet.py 1000 1308 0.0 0.9 35608 18564 ? S 15:58 0:00 python /usr/share/screenlets-manager/screenlets-daemon.py 1000 1309 0.0 0.3 19524 6468 ? S 15:58 0:00 /usr/lib/policykit-1-gnome/polkit-gnome-authentication-agent-1 1000 1311 0.0 0.5 37412 11788 ? S 15:58 0:01 gnome-power-manager 1000 1312 0.0 1.0 50772 22628 ? S 15:58 0:03 gnome-panel 1000 1313 0.1 1.5 102648 31184 ? Sl 15:58 0:10 nautilus root 1314 0.0 0.0 5188 996 ? S 15:58 0:02 udisks-daemon: polling /dev/sdb /dev/sr0 1000 1315 0.0 0.6 51948 12464 ? SL 15:58 0:01 nm-applet --sm-disable 1000 1317 0.0 0.1 16956 2364 ? Sl 15:58 0:00 /usr/lib/gvfs/gvfs-afc-volume-monitor 1000 1318 0.0 0.3 20164 7792 ? S 15:58 0:00 bluetooth-applet 1000 1321 0.0 0.1 7260 2384 ? S 15:58 0:00 /usr/lib/gvfs/gvfs-gphoto2-volume-monitor 1000 1323 0.0 0.5 37436 12124 ? S 15:58 0:00 /usr/lib/notify-osd/notify-osd 1000 1324 0.0 1.9 197928 40456 ? Ssl 15:58 0:06 /home/alexandros/.dropbox-dist/dropbox 1000 1329 0.0 0.3 20136 7968 ? S 15:58 0:00 /usr/bin/gnome-screensaver --no-daemon 1000 1331 0.0 0.1 7056 3112 ? S 15:58 0:00 /usr/lib/gvfs/gvfsd-trash --spawner :1.6 /org/gtk/gvfs/exec_spaw/0 root 1340 0.0 0.0 2236 1008 ? S 15:58 0:00 /sbin/dhclient -d -sf /usr/lib/NetworkManager/nm-dhcp-client.action -pf /var/run/dhcl 1000 1348 0.0 0.1 42252 3680 ? Ssl 15:58 0:00 /usr/lib/bonobo-activation/bonobo-activation-server --ac-activate --ior-output-fd=19 1000 1384 0.0 1.7 80244 35480 ? Sl 15:58 0:02 /usr/bin/python /usr/lib/deskbar-applet/deskbar-applet/deskbar-applet --oaf-activate- 1000 1388 0.0 0.5 26196 11804 ? S 15:58 0:01 /usr/lib/gnome-panel/wnck-applet --oaf-activate-iid=OAFIID:GNOME_Wncklet_Factory --oa 1000 1393 0.1 0.5 25876 11548 ? S 15:58 0:08 /usr/lib/gnome-applets/multiload-applet-2 --oaf-activate-iid=OAFIID:GNOME_MultiLoadAp 1000 1394 0.0 0.5 25600 11140 ? S 15:58 0:03 /usr/lib/gnome-applets/cpufreq-applet --oaf-activate-iid=OAFIID:GNOME_CPUFreqApplet_F 1000 1415 0.0 0.5 39192 11156 ? S 15:58 0:01 /usr/lib/gnome-power-manager/gnome-inhibit-applet --oaf-activate-iid=OAFIID:GNOME_Inh 1000 1417 0.0 0.7 53544 15488 ? Sl 15:58 0:00 /usr/lib/gnome-applets/mixer_applet2 --oaf-activate-iid=OAFIID:GNOME_MixerApplet_Fact 1000 1419 0.0 0.4 23816 9068 ? S 15:58 0:00 /usr/lib/gnome-panel/notification-area-applet --oaf-activate-iid=OAFIID:GNOME_Notific 1000 1488 0.0 0.3 20964 7548 ? S 15:58 0:00 /usr/lib/gnome-disk-utility/gdu-notification-daemon 1000 1490 0.0 0.1 6608 2484 ? S 15:58 0:00 /usr/lib/gvfs/gvfsd-burn --spawner :1.6 /org/gtk/gvfs/exec_spaw/1 1000 1510 0.0 0.1 6348 2084 ? S 15:58 0:00 /usr/lib/gvfs/gvfsd-metadata 1000 1531 0.0 0.3 19472 6616 ? S 15:58 0:00 /usr/lib/gnome-user-share/gnome-user-share 1000 1535 0.0 0.4 77128 8392 ? Sl 15:58 0:00 /usr/lib/evolution/evolution-data-server-2.28 --oaf-activate-iid=OAFIID:GNOME_Evoluti 1000 1601 0.0 0.5 69576 11800 ? Sl 15:59 0:00 /usr/lib/evolution/2.28/evolution-alarm-notify 1000 1604 0.0 0.7 33924 15888 ? S 15:59 0:00 python /usr/share/system-config-printer/applet.py 1000 1701 0.0 0.5 37116 11968 ? S 15:59 0:00 update-notifier 1000 1892 4.5 7.0 406720 145312 ? Sl 17:11 3:09 /opt/google/chrome/chrome 1000 1896 0.0 0.1 69812 3680 ? S 17:11 0:02 /opt/google/chrome/chrome 1000 1898 0.0 0.6 91420 14080 ? S 17:11 0:00 /opt/google/chrome/chrome --type=zygote 1000 1916 0.2 1.3 140780 27220 ? Sl 17:11 0:12 /opt/google/chrome/chrome --type=extension --disable-client-side-phishing-detection - 1000 1918 0.7 1.8 155720 37912 ? Sl 17:11 0:31 /opt/google/chrome/chrome --type=extension --disable-client-side-phishing-detection - 1000 1921 0.0 1.0 135904 21052 ? Sl 17:11 0:02 /opt/google/chrome/chrome --type=extension --disable-client-side-phishing-detection - 1000 1927 6.5 3.6 194604 74960 ? Sl 17:11 4:32 /opt/google/chrome/chrome --type=renderer --disable-client-side-phishing-detection -- 1000 2156 0.4 0.7 48344 14896 ? Rl 18:03 0:04 gnome-terminal 1000 2157 0.0 0.0 1988 712 ? S 18:03 0:00 gnome-pty-helper 1000 2158 0.0 0.1 6504 3860 pts/0 Ss 18:03 0:00 bash 1000 2564 0.2 0.1 6624 3984 pts/1 Ss+ 18:17 0:00 bash 1000 2711 0.0 0.0 4208 1352 ? S 18:19 0:00 /bin/bash /home/alexandros/Programme/TeamSpeak3-Client-linux_x86_back/ts3client_runsc 1000 2714 36.5 1.5 210872 31960 ? SLl 18:19 0:18 ./ts3client_linux_x86 1000 2743 0.0 0.0 2716 1068 pts/0 R+ 18:20 0:00 ps aux Output of vmstat: alexandros@alexandros-laptop:~$ vmstat procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 0 1093324 69840 449496 0 0 27 10 476 667 6 2 91 1 Output of lsusb alexandros@alexandros-laptop:~$ lspci 00:00.0 Host bridge: Silicon Integrated Systems [SiS] 671MX 00:01.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge 00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS968 [MuTIOL Media IO] (rev 01) 00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev 01) 00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) 00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) 00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller 00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA Controller / IDE mode (rev 03) 00:06.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge 00:07.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge 00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 00:0f.0 Audio device: Silicon Integrated Systems [SiS] Azalia Audio Controller 01:00.0 VGA compatible controller: ATI Technologies Inc Mobility Radeon X2300 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) The Team Speak log file : 2011-06-19 19:04:04.223522|INFO | | | Logging started, clientlib version: 3.0.0-rc2 [Build: 14642] 2011-06-19 19:04:04.761149|ERROR |SoundBckndIntf| | /home/alexandros/Programme/TeamSpeak3-Client-linux_x86_back/soundbackends/libpulseaudio_linux_x86.so error: NOT_CONNECTED 2011-06-19 19:04:05.871770|INFO |ClientUI | | Failed to init text to speech engine 2011-06-19 19:04:05.894623|INFO |ClientUI | | TeamSpeak 3 client version: 3.0.0-rc2 [Build: 14642] 2011-06-19 19:04:05.895421|INFO |ClientUI | | Qt version: 4.7.2 2011-06-19 19:04:05.895571|INFO |ClientUI | | Using configuration location: /home/alexandros/.ts3client/ts3clientui_qt.conf 2011-06-19 19:04:06.559596|INFO |ClientUI | | Last update check was: Sa. Jun 18 00:08:43 2011 2011-06-19 19:04:06.560506|INFO | | | Checking for updates... 2011-06-19 19:04:07.357869|INFO | | | Update check, my version: 14642, latest version: 14642 2011-06-19 19:05:52.978481|INFO |PreProSpeex | 1| Speex version: 1.2rc1 2011-06-19 19:05:54.055347|INFO |UIHelpers | | setClientVolumeModifier: 10 -8 2011-06-19 19:05:54.057196|INFO |UIHelpers | | setClientVolumeModifier: 11 2 Thanks for taking the time to read my message. UPDATE: Thanks to nickguletskii's link I googled for "alsa cpu usage" (without quotes) and it brought me to a forum. A user wrote that by directly selecting the hardware with "plughw:x.x" won't impact the performance of the system. I have selected it in the TS 3 configuration and it worked. But this solution is not optimal because now no other program can access the sound output. If you need any further information or my question is unclear than please tell me.

  Read the article

• How to Disable Access to the Registry in Windows 7

  - by Mysticgeek

  If you don’t know what your doing in the Registry, you can mess up your computer pretty good. Today we show you how to prevent users from accessing the Registry and making any changes to it. Using Local Group Policy Editor Note: This method uses Group Policy Editor which is not available in Home versions of Windows. First type gpedit.msc into the Search box in the Start menu. When Group Policy Editor opens, navigate to User Configuration \ Administrative Templates then select System. Under Setting in the right panel double-click on Prevent access to registry editing tools. Select the radio button next to Enabled, click OK, then close out of Group Policy Editor. Now if a user tries to access the Registry… They will get the following message advising they cannot access it.   Using Registry Enabler & Disabler 3 If you’re using Home or Starter version of Windows 7, you can use a neat utility called Registry Enabler & Disabler (link below). This app works on XP and Vista as well. There is no installation involved so you can run it from a flash drive, disable the registry, then take the flash drive with you while a the user is on the machine.   Again, if the user tries to access the Registry they will get the following error… Using one of these options will stop users from gaining access to the Registry or running any registry hacks. Of course if you have a shared computer, you may want to set up other users with a Standard Account, as they won’t be able to make changes to the Registry anyway. Download Registry Enabler & Disabler 3 Similar Articles Productive Geek Tips Disable Notification Balloons in XPDisable/Enable Lock Workstation Functionality (Windows + L)Disable Windows Mobility Center in Windows 7 or VistaRegistry Hack to Disable Writing to USB DrivesSpeed Up Disk Access by Disabling Last Access Updating in Windows XP TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows Fun with 47 charts and graphs Tomorrow is Mother’s Day Check the Average Speed of YouTube Videos You’ve Watched OutlookStatView Scans and Displays General Usage Statistics How to Add Exceptions to the Windows Firewall Office 2010 reviewed in depth by Ed Bott

  Read the article

• Accessing JMX for Oracle WebLogic 11g

  - by Anthony Shorten

  In Oracle Utilities Application Framework V4, we use the latest Oracle WebLogic release (11g). The instructions below illustrate a way of allowing a console like jconsole to remotely monitor and manage Oracle WebLogic using the JMX Mbeans. Typically management of Oracle WebLogic is done from Oracle Enterprise Manager or the Oracle Weblogic console application but you can also use JMX. To access the JMX capability for Oracle WebLogic 11g, for an Oracle Utilities Application Framework based product, using a JMX console (such as jconsole) the following process needs to be performed: Enable the JMX Management Server in the Oracle WebLogic console at splapp - Configuration - General - Advanced Settings option. Enable both Compatibility Mbean Server Enabled and Management EJB Enabled (this enables the legacy and new JMX interface). Save the changes This change will require a restart. In the startup of the Oracle WebLogic server in the $SPLSYSTEMLOGS/myserver.log (or %SPLESYSTEMLOGS%\myserver.log on Windows) you will see the BEA-149512 message indicating the Mbean servers have been started. The message will indicate the JMX URL that can be used to access the JMX Mbeans. The URL is in the format: service:jmx:iiop://host:port/jndi/mbeanserver where: host - Oracle WebLogic host name port - Oracle WebLogic port number mbeanserver - Mbean Server to access. Valid Values: weblogic.management.mbeanservers.runtime weblogic.management.mbeanservers.edit weblogic.management.mbeanservers.domainruntime For illustrative purposes we will use the domainruntime Mbean. Ensure that you execute the splenviron[.sh] utility to set the appropriate environment variables for the desired environment. Execute the following jconsole command to initiate the connection to the JMX Mbean server Windows: jconsole -J-Djava.class.path=%JAVA_HOME%\lib\jconsole.jar;%WL_HOME%\server\lib\wljmxclient.jar -J-Djmx.remote.protocol.provider.pkgs=weblogic.management.remote Linux/Unix jconsole -J-Djava.class.path=$JAVA_HOME/lib/jconsole.jar;$WL_HOME/server/lib/wljmxclient.jar -J-Djmx.remote.protocol.provider.pkgs=weblogic.management.remote You will see a New Connection Dialog. Specify the URL from the previous steps into the Remote process (i.,e. service:jmx:iiop...). The credentials are the credentials specified for the Oracle WebLogic console. You are now able to view the JMX classes available. Here is an example from my demonstration machine: Refer to the Oracle WebLogic Mbean documentation to understand the output.

  Read the article

• A few things I learned regarding Azure billing policies

  - by Vincent Grondin

  An hour of small computing time: 0,12$ per hour A Gig of storage in the cloud: 0,15$ per hour 1 Gig of relational database using Azure SQL: 9,99$  per month A Visual Studio Professional with MSDN Premium account: 2500$ per year Winning an MSDN Professional account that comes preloaded with 750 free hours of Azure per month:  PRICELESS !!!      But was it really free???? Hmmm… Let’s see.....   Here's a few things I learned regarding Azure billing policies when I attended a promotional training at Microsoft last week...   1)  An instance deployed in the cloud really means whatever you upload in there... it doesn't matter if it's in STAGING OR PRODUCTION!!!!   Your MSDN account comes with 750 free hours of small computing time per month which should be enough hours per month for one instance of one application deployed in the cloud...  So we're cool, the application you run in the cloud doesn't cost you a penny....  BUT the one that's in staging is still consuming time!!!   So if you don’t want to end up having to pay 42$ at the end of the month on your credit card like this happened to a friend of mine, DELETE them staging applications once you’ve put them in production! This also applies to the instance count you can modify in the configuration file… So stop and think before you decide you want to spawn 50 of those hello world apps  .     2) If you have an MSDN account, then you have the promotional 750 hours of Azure credits per month and can use the Azure credits to explore the Cloud! But be aware, this promotion ends in 8 months (maybe more like 7 now) and then you will most likely go back to the standard 250 hours of Azure credits. If you do not delete your applications by then, you’ll get billed for the extra hours, believe me…   There is a switch that you can toggle and which will STOP your automatic enrollment after the promotion and prevent you from renewing the Azure Account automatically. Yes the default setting is to automatically renew your account and remember, you entered your credit card information in the registration process so, yes, you WILL be billed…  Go disable that ASAP    Log into your account, go to “Windows Azure Platform” then click the “Subscriptions” tab and on the right side, you’ll see a drop down with different “Actions” into it… Choose “Opt out of auto renew” and, NOW you’re safe…   Still, this is a great offer by Microsoft and I think everyone that has a chance should play a bit with Azure to get to know this technology a bit more...     Happy Cloud Computing All

  Read the article

• Gnome Shell segfault in libglib-2.0

  - by slohui

  I have been using Ubuntu 11.10 + Gnome Shell with a Nvidia card, but now I've moved it to my new PC which has an ATI card, at first it wasn't booting but I installed the driver from amd.com and then it worked. Anyway my problem is that gnome-shell is crashing, mostly when I try to start a VirtualBox machine (it happened in other times but I don't remember what I was doing). Sometimes gnome-shell respawns and it continue working but sometimes it doesn't so I have to restart lightdm and lose all the windows I was using. Here's some of the syslog when the crash occurs: Apr 9 12:20:08 desktop-1 NetworkManager[1032]: SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/vboxnet0, iface: vboxnet0) Apr 9 12:20:08 desktop-1 NetworkManager[1032]: SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/vboxnet0, iface: vboxnet0): no ifupdown configuration found. Apr 9 12:20:08 desktop-1 NetworkManager[1032]: <warn> /sys/devices/virtual/net/vboxnet0: couldn't determine device driver; ignoring... Apr 9 12:20:08 desktop-1 kernel: [ 4498.689561] warning: `VirtualBox' uses 32-bit capabilities (legacy support in use) Apr 9 12:24:29 desktop-1 gnome-session[1617]: WARNING: Application 'gnome-shell.desktop' killed by signal Apr 9 12:24:45 desktop-1 gnome-session[1617]: WARNING: App 'gnome-shell.desktop' respawning too quickly Apr 9 12:24:45 desktop-1 gnome-session[1617]: CRITICAL: We failed, but the fail whale is dead. Sorry.... Apr 9 12:25:20 desktop-1 kernel: [ 4810.769775] show_signal_msg: 30 callbacks suppressed |----- > Apr 9 12:25:20 desktop-1 kernel: [ 4810.769785] gnome-shell[3427]: segfault at b0 ip b6bd09cd sp bfc9b650 error 4 in libglib-2.0.so.0.3000.0[b6b71000+f7000]** Apr 9 12:25:20 desktop-1 gnome-session[1617]: WARNING: Application 'gnome-shell.desktop' killed by signal Apr 9 12:25:23 desktop-1 kernel: [ 4814.055705] EXT4-fs (sda1): Unaligned AIO/DIO on inode 133295 by VirtualBox; performance will be poor. Apr 9 12:26:55 desktop-1 gnome-session[1617]: Gdk-WARNING: gnome-session: Fatal IO error 11 (Resource temporarily unavailable) on X server :0.#012 Apr 9 12:26:55 desktop-1 kernel: [ 4905.373256] [fglrx] IRQ 56 Disabled Apr 9 12:26:59 desktop-1 acpid: client 1124[0:0] has disconnected Apr 9 12:26:59 desktop-1 acpid: client connected from 3864[0:0] Apr 9 12:26:59 desktop-1 acpid: 1 client rule loaded Apr 9 12:26:59 desktop-1 kernel: [ 4909.700095] fglrx_pci 0000:02:00.0: irq 56 for MSI/MSI-X Apr 9 12:26:59 desktop-1 kernel: [ 4909.701466] [fglrx] Firegl kernel thread PID: 3867 Apr 9 12:26:59 desktop-1 kernel: [ 4909.701625] [fglrx] Firegl kernel thread PID: 3868 Apr 9 12:26:59 desktop-1 kernel: [ 4909.701852] [fglrx] Firegl kernel thread PID: 3869 Apr 9 12:26:59 desktop-1 kernel: [ 4909.702021] [fglrx] IRQ 56 Enabled Apr 9 12:26:59 desktop-1 kernel: [ 4909.861815] [fglrx] Gart USWC size:1280 M. Apr 9 12:26:59 desktop-1 kernel: [ 4909.861817] [fglrx] Gart cacheable size:508 M. Apr 9 12:26:59 desktop-1 kernel: [ 4909.861820] [fglrx] Reserved FB block: Shared offset:0, size:1000000 Apr 9 12:26:59 desktop-1 kernel: [ 4909.861821] [fglrx] Reserved FB block: Unshared offset:f8fd000, size:403000 Apr 9 12:26:59 desktop-1 kernel: [ 4909.861823] [fglrx] Reserved FB block: Unshared offset:3fff4000, size:c000 Does anyone could guide me on how to fix this? Or the proper place where to ask for help.

  Read the article

• JRockit R28/JRockit Mission Control 4.0 is out!

  - by Marcus Hirt

  The next major release of JRockit is finally out! Here are some highlights: Includes the all new JRockit Flight Recorder – supersedes the old JRockit Runtime Analyser. The new flight recorder is inspired by the “black box” in airplanes. It uses a highly efficient recording engine and thread local buffers to capture data about the runtime and the application running in the JVM. It can be configured to always be on, so that whenever anything “interesting” happens, data can be dumped for some time back. Think of it as your own personal profiling time machine. Automatic shortest path calculation in Memleak – no longer any need for running around in circles when trying to find your way back to a thread root from an instance. Memleak can now show class loader related information and split graphs on a per class loader basis. More easily configured JMX agent – default port for both RMI Registry and RMI Server can be configured, and is by default the same, allowing easier configuration of firewalls. Up to 64 GB (was 4GB) compressed references. Per thread allocation profiling in the Management Console. Native Memory Tracking – it is now possible to track native memory allocations with very high resolution. The information can either be accessed using JRCMD, or the dedicated Native Memory Tracking experimental plug-in for the Management Console (alas only available for the upcoming 4.0.1 release). JRockit can now produce heap dumps in HPROF format. Cooperative suspension – JRockit is no longer using system signals for stopping threads, which could lead to hangs if signals were lost or blocked (for example bad NFS shares). Now threads check periodically to see if they are suspended. VPAT/Section 508 compliant JRMC – greatly improved keyboard navigation and screen reader support. See New and Noteworthy for more information. JRockit Mission Control 4.0.0 can be downloaded from here: http://www.oracle.com/technology/software/products/jrockit/index.html <shameless ad> There is even a book to go with JRMC 4.0.0/JRockit R28! http://www.packtpub.com/oracle-jrockit-the-definitive-guide/book/ </shameless ad>

  Read the article

• MAXDOP in SQL Azure

  - by Herve Roggero

  In my search of better understanding the scalability options of SQL Azure I stumbled on an interesting aspect: Query Hints in SQL Azure. More specifically, the MAXDOP hint. A few years ago I did a lot of analysis on this query hint (see article on SQL Server Central:  http://www.sqlservercentral.com/articles/Configuring/managingmaxdegreeofparallelism/1029/).  Here is a quick synopsis of MAXDOP: It is a query hint you use when issuing a SQL statement that provides you control with how many processors SQL Server will use to execute the query. For complex queries with lots of I/O requirements, more CPUs can mean faster parallel searches. However the impact can be drastic on other running threads/processes. If your query takes all available processors at 100% for 5 minutes... guess what... nothing else works. The bottom line is that more is not always better. The use of MAXDOP is more art than science... and a whole lot of testing; it depends on two things: the underlying hardware architecture and the application design. So there isn't a magic number that will work for everyone... except 1... :) Let me explain. The rules of engagements are different. SQL Azure is about sharing. Yep... you are forced to nice with your neighbors.  To achieve this goal SQL Azure sets the MAXDOP to 1 by default, and ignores the use of the MAXDOP hint altogether. That means that all you queries will use one and only one processor.  It really isn't such a bad thing however. Keep in mind that in some of the largest SQL Server implementations MAXDOP is usually also set to 1. It is a well known configuration setting for large scale implementations. The reason is precisely to prevent rogue statements (like a SELECT * FROM HISTORY) from bringing down your systems (like a report that should have been running on a different in the first place) and to avoid the overhead generated by executing too many parallel queries that could cause internal memory management nightmares to the host Operating System. Is summary, forcing the MAXDOP to 1 in SQL Azure makes sense; it ensures that your database will continue to function normally even if one of the other tenants on the same server is running massive queries that would otherwise bring you down. Last but not least, keep in mind as well that when you test your database code for performance on-premise, make sure to set the DOP to 1 on your SQL Server databases to simulate SQL Azure conditions.

  Read the article

• Configure 27" 2560x1440 for a monitor with corrupt EDID

  - by Aras

  I am trying to get a monitor work with my Ubuntu laptop. The monitor is this cheap 27" Korean monitors which has a 2560x1440 resolution -- and nothing else. Here are some specifications of this monitor: 2560x1440 @60Hz Only one dual link DVI-D input -- no other input port (no HDMI or display port) no OSD no scalar reports corrupt EDID does 2560x1440 @60Hz, did I say that already? Anyways, the monitor works beautifully with my Ubuntu desktop which has an nVidia card with DVI output. However, I am having problem using this monitor with my laptop. After some searching around I found a few posts suggesting to use an active adaptor for mini display port, so I went and bought a mini display to dual link DVI-D adaptor.. When using this adaptor the monitor is recognized by nvidia-settings tool but with incorrect resolution information. As you can see the monitor is incorrectly recognized and there are no other resolution available to set. This post on ubuntu forums and this other post on overclock both suggest that the monitor is reporting corrupt EDID file. I have tried following their instructions, but so far I have not been able to display any image on the monitor from my laptop. The laptop I am using is an ASUS G75VW with a 1920x1080 screen. It has a VGA, an HDMI 1.4a, and a mini display port. The graphic card is an nvidia gforce gtx 660M with 2GB dedicated memory. I am running Ubuntu 12.10 on here which I upgrade from 12.04 a few weeks ago. As I said I have tried several suggestions, including specifying Modeline in xorg.conf and also linking to EDID files I found from those forum posts above. However, I am not sure if the EDID files I found are suitable for my monitor. I think the solution to my problem consist of obtaining the EDID file of my monitor and then fixing it and modifying xorg.conf to force nvidia driver to load the correct resolution. However, I am not sure what steps I need to take to do this. Here is the part of sudo xrandr --prop output that is related to this monitor: DP-1 connected 800x600+1920+0 (normal left inverted right x axis y axis) 0mm x 0mm SignalFormat: DisplayPort supported: DisplayPort ConnectorType: DisplayPort ConnectorNumber: 3 (0x00000003) _ConnectorLocation: 3 (0x00000003) 800x600 60.3*+ I was expecting to see the EDID file in this output as was mentioned in this post, but it is not there. After several hours of tweaking X configurations, I decided it was time to ask for help here. I would really appreciate if someone with experience regarding EDID and X configuration could give me a hand to solve this issue.

  Read the article

• SQL SERVER – Maximize Database Performance with DB Optimizer – SQL in Sixty Seconds #054

  - by Pinal Dave

  Performance tuning is an interesting concept and everybody evaluates it differently. Every developer and DBA have different opinion about how one can do performance tuning. I personally believe performance tuning is a three step process Understanding the Query Identifying the Bottleneck Implementing the Fix While, we are working with large database application and it suddenly starts to slow down. We are all under stress about how we can get back the database back to normal speed. Most of the time we do not have enough time to do deep analysis of what is going wrong as well what will fix the problem. Our primary goal at that time is to just fix the database problem as fast as we can. However, here is one very important thing which we need to keep in our mind is that when we do quick fix, it should not create any further issue with other parts of the system. When time is essence and we want to do deep analysis of our system to give us the best solution we often tend to make mistakes. Sometimes we make mistakes as we do not have proper time to analysis the entire system. Here is what I do when I face such a situation – I take the help of DB Optimizer. It is a fantastic tool and does superlative performance tuning of the system. Everytime when I talk about performance tuning tool, the initial reaction of the people is that they do not want to try this as they believe it requires lots of the learning of the tool before they use it. It is absolutely not true with the case of the DB optimizer. It is a very easy to use and self intuitive tool. Once can get going with the product, in no time. Here is a quick video I have build where I demonstrate how we can identify what index is missing for query and how we can quickly create the index. Entire three steps of the query tuning are completed in less than 60 seconds. If you are into performance tuning and query optimization you should download DB Optimizer and give it a go. Let us see the same concept in following SQL in Sixty Seconds Video: You can Download DB Optimizer and reproduce the same Sixty Seconds experience. Related Tips in SQL in Sixty Seconds: Performance Tuning – Part 1 of 2 – Getting Started and Configuration Performance Tuning – Part 2 of 2 – Analysis, Detection, Tuning and Optimizing What would you like to see in the next SQL in Sixty Seconds video? Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: Database, Pinal Dave, PostADay, SQL, SQL Authority, SQL in Sixty Seconds, SQL Interview Questions and Answers, SQL Query, SQL Scripts, SQL Server, SQL Tips and Tricks, T SQL, Technology, Video Tagged: Identity

  Read the article

• Oracle Utilities Application Framework future feature deprecation

  - by Paula Speranza-Hadley

  From time to time, existing functionality is replaced with alternative features to offer greater flexibility and standardization. In Oracle Utilities Application Framework V4.2.0.0.0 the following features are being announced for deprecation in the next release or have been previously announced and are not being delivered with this version of the Oracle Utilities Application Framework: ·         No SQL Server Support – Oracle Utilities Application Framework V4.2.0.0.0 or above does not ship with any support for SQL Server. ·         No MPL Support – Oracle Utilities Application Framework V4.2.0.0.0 or above does not ship with the Multi-Purpose Listener (MPL) component of the XML Application Integration (XAI) component. Customers using the MPL should migrate to Oracle Service Bus. ·         No provided Crystal Reports/Business Objects Interface – Oracle Utilities Application Framework V4.2.0.0.0 or above does not ship with a supported Crystal Reports/Business Objects Interface. This facility is now available as downloadable customization for existing or new customers. Responsibility for maintenance and new features is now individual customer's responsibility. ·         XAI Servlet deprecation – The XAI Servlet (xaiserver and classicxai) will be removed in the next release of the Oracle Utilities Application Framework. Customers are encouraged to migrate to the native Web Services Support as outlined in XAI Best Practices whitepaper available from My Oracle Support (Doc Id: 942074.1). ·         ConfigLab deprecation – The ConfigLab facility will be removed in the next release of Oracle Utilities Application Framework for products it is shipped with. Customers are recommended to migrate to the Configuration Migration Assistant which provides the same and more functionality.   ·         Archiving deprecation – The inbuilt Archiving has been removed from Oracle Utilities Application Framework V4.2.0.0.0 or above, for products it is shipped with. Customers considering Archiving solution should migrate to the Information Lifecycle Management based solution provided for your product. ·         DISTRIBUTED batch execution mode deprecation – The DISTRIBUTED execution mode used by the batch component of the Oracle Utilities Application Framework will be deprecated in the next release of the Oracle Utilities Application Framework. Customers using DISTRUBUTED mode should migrate to CLUSTERED mode as outlined in the Batch Best Practices For Oracle Utilities Application Framework Based Products whitepaper available from My Oracle Support (Doc Id: 836362.1). ·         XAI Schema Editor deprecation – The XAI Schema Editor which is a component of the Oracle Utilities Software Development Kit will be removed in the next release of the Oracle Utilities Application Framework. Customers should migrate their existing schemas to Business Object based schemas and use the browser based Schema Editor instead.  

  Read the article

• Getting Started With nServiceBus on VAN Mar 31

  - by van

  Topic: nServiceBus is mature and powerful open source framework that enables to design robust, scalable, message-based, service-oriented architectures. Latest improvements in the configuration API enables developers to quickly get started and build a working simple system that uses messaging infrastructure. The goal of this session is to give a jump start with the framework, introduce basic concepts such as message handlers, Sagas, Pub/Sub, Generic Host and also create a working demo application that uses publish/subscribe messaging. The content of the session is addressed to developers that are interested in learning how to get started using nServiceBus in order to design and build distributed systems. Bio: Bernard Kowalski is currently a Software Developer at Microdesk, one of Autodesk's leading partners in providing variety of Geospatial and Computer-Aided Design solutions. Bernard has experience developing .NET framework-based applications utilizing Windows Forms, Windows Services, ASP.NET MVC, and Web services. In a recent project, Bernard architected and implemented a distributed system based on SOA principles using an open source implementation of an Enterprise Service Bus. Bernard develops software with Agile patterns and practices using Domain Driven Design combined with TDD (Test Driven Development). He is familiar with all of the following APIs: Autodesk Vault/Product Stream API, AutoCAD ActiveX/VBA/.NET API, AutoCAD Mechanical API, Autodesk Inventor API, Autodesk MapGuide Enterprise. Prior to joining Microdesk, Bernard worked as a researcher and teacher at the University of Science and Technology in Krakow, Poland where he was awarded with a PhD in Computer Methods in Materials Science. He also participated in research projects where he developed applications for analysis of hot compression test results using advanced optimization techniques. He also developed Finite Element Method-based programs for thermal and stress analysis using C++ and FORTRAN. Bernard is a member of the Domain Driven Design and ALT.NET user groups in NYC. Virtual ALT.NET (VAN) is the online gathering place of the ALT.NET community. Through conversations, presentations, pair programming and dojos, we strive to improve, explore, and challenge the way we create software. Using net conferencing technology such as Skype and LiveMeeting, we hold regular meetings, open to anyone, usually taking the form of a presentation or an Open Space Technology-style conversation. Please see the Calendar(http://www.virtualaltnet.com/Home/Calendar) to find a VAN group that meets at a time convenient to you, and feel welcome to join a meeting. Past sessions can be found on the Recording page. To stay informed about VAN activities, you can subscribe to the Virtual ALT.NET Google Group and follow the Virtual ALT.NET blog. Times below are Central Standard Time Start Time: Wed, Mar 31, 2010 8:00 PM UTC/GMT -5 hours End Time: Wed, Mar 31, 2010 10:00 PM UTC/GMT -5 hours Attendee URL: http://www.virtualaltnet.com/van Zach Young http://www.virtualaltnet.com

  Read the article

< Previous Page | 440 441 442 443 444 445 446 447 448 449 450 451  | Next Page >