Search Results

Search found 41561 results on 1663 pages for 'linux command'.

Page 446/1663 | < Previous Page | 442 443 444 445 446 447 448 449 450 451 452 453  | Next Page >

• Can't set-up Wifi Adhoc on my Raspberry Pi with an USB dongle

  - by Wouter

  I am trying to set-up an access point (ad-hoc) for my Raspberry Pi. That means I'm trying to "share" the ethernet connection over Wi-Fi. I am doing this using my Ralink Technology, Corp. RT2501/RT2573 Wireless Adapter. When following a tutorial (or actually every tutorial), it immediately goes wrong. root@pinkypi:/home/pi# iwconfig wlan0 mode ad-hoc Error for wireless request "Set Mode" (8B06) : SET failed on device wlan0 ; Device or resource busy. I already tried ifdown and not having it in the USB port at the startup. If it helps, every action with the thing fail (or at least setting the mode). I am using Debian. I'm sure I'm overseeing something, but I can't find out what. What is wrong?

  Read the article

• Packet loss with Broadcom wireless and Ubuntu

  - by stevemegson

  I have a machine with Ubuntu 9.04 and a Broadcom BCM4306 wireless card which has been running quite happily for many months with the b43legacy driver that's suggested by Hardware Drivers. Suddenly, I'm now seeing crippling packet loss, varying between 30% and 90% when pinging the router. My WinXP machine is still quite happy even when sat next to the Ubuntu box, so I assume that it's not some new source of interference. What else is likely to have changed? How should I go about diagnosing and fixing this?

  Read the article

• VPN in Ubuntu fails every time

  - by fazpas

  I am trying to setup a vpn connection in Ubuntu 10.04 to use the service from relakks.com I used the network manager to add the vpn connection and the settings are: Gateway: pptp.relakks.com Username: user Password: pwd IPv4 Settings: Automatic (VPN) Advanced: MSCHAP & MSCHAPv2 checked Use point-to-point encryption (security:default) Allow BSD data compression checked Allow deflate data compression checked Use TCP header compression checked The connection always fail, here is the syslog: Jun 27 20:11:56 desktop NetworkManager: <info> Starting VPN service 'org.freedesktop.NetworkManager.pptp'... Jun 27 20:11:56 desktop NetworkManager: <info> VPN service 'org.freedesktop.NetworkManager.pptp' started (org.freedesktop.NetworkManager.pptp), PID 2064 Jun 27 20:11:56 desktop NetworkManager: <info> VPN service 'org.freedesktop.NetworkManager.pptp' just appeared, activating connections Jun 27 20:11:56 desktop NetworkManager: <info> VPN plugin state changed: 3 Jun 27 20:11:56 desktop NetworkManager: <info> VPN connection 'Relakks' (Connect) reply received. Jun 27 20:11:56 desktop pppd[2067]: Plugin /usr/lib/pppd/2.4.5//nm-pptp-pppd-plugin.so loaded. Jun 27 20:11:56 desktop pppd[2067]: pppd 2.4.5 started by root, uid 0 Jun 27 20:11:56 desktop NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/ppp1, iface: ppp1) Jun 27 20:11:56 desktop NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/ppp1, iface: ppp1): no ifupdown configuration found. Jun 27 20:11:56 desktop pppd[2067]: Using interface ppp1 Jun 27 20:11:56 desktop pppd[2067]: Connect: ppp1 <--> /dev/pts/0 Jun 27 20:11:56 desktop pptp[2071]: nm-pptp-service-2064 log[main:pptp.c:314]: The synchronous pptp option is NOT activated Jun 27 20:11:57 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 1 'Start-Control-Connection-Request' Jun 27 20:11:58 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_disp:pptp_ctrl.c:739]: Received Start Control Connection Reply Jun 27 20:11:58 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_disp:pptp_ctrl.c:773]: Client connection established. Jun 27 20:11:58 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 7 'Outgoing-Call-Request' Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_disp:pptp_ctrl.c:858]: Received Outgoing Call Reply. Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_disp:pptp_ctrl.c:897]: Outgoing call established (call ID 0, peer's call ID 1024). Jun 27 20:11:59 desktop kernel: [ 56.564074] Inbound IN=ppp0 OUT= MAC= SRC=93.182.139.2 DST=186.110.76.26 LEN=61 TOS=0x00 PREC=0x00 TTL=52 ID=40460 DF PROTO=47 Jun 27 20:11:59 desktop kernel: [ 56.944054] Inbound IN=ppp0 OUT= MAC= SRC=93.182.139.2 DST=186.110.76.26 LEN=60 TOS=0x00 PREC=0x00 TTL=52 ID=40461 DF PROTO=47 Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[pptp_read_some:pptp_ctrl.c:544]: read returned zero, peer has closed Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[callmgr_main:pptp_callmgr.c:258]: Closing connection (shutdown) Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 12 'Call-Clear-Request' Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[pptp_read_some:pptp_ctrl.c:544]: read returned zero, peer has closed Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[call_callback:pptp_callmgr.c:79]: Closing connection (call state) Jun 27 20:11:59 desktop pppd[2067]: Modem hangup Jun 27 20:11:59 desktop pppd[2067]: Connection terminated. Jun 27 20:11:59 desktop NetworkManager: <info> VPN plugin failed: 1 Jun 27 20:11:59 desktop NetworkManager: SCPlugin-Ifupdown: devices removed (path: /sys/devices/virtual/net/ppp1, iface: ppp1) Jun 27 20:11:59 desktop pppd[2067]: Exit. Does someone can identify something in the syslog? I've been googling and reading about pptp but couldn't find anything about the error "read returned zero, peer has closed"

  Read the article

• if I put accept all 0.0.0.0/0 means this server is totally open for any ip ?

  - by davyzhang

  ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 is this means allow all ip from all port? but I still can not visit the server except I go through the allowed ip address and if I put this line in any line, did I make this server totally open for any connection? the full iptable list is below Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 116.211.25.89 0.0.0.0/0 ACCEPT all -- 222.215.136.8 0.0.0.0/0 ACCEPT all -- 125.82.87.21 0.0.0.0/0 ACCEPT all -- 127.0.0.1 127.0.0.1 ACCEPT tcp -- 61.172.251.109 0.0.0.0/0 tcp spt:8080 ACCEPT tcp -- 61.172.254.123 0.0.0.0/0 tcp spt:8080 ACCEPT tcp -- 61.129.44.191 0.0.0.0/0 ACCEPT tcp -- 61.129.44.128 0.0.0.0/0 ACCEPT tcp -- 61.172.251.109 0.0.0.0/0 tcp spt:8080 ACCEPT tcp -- 61.172.254.123 0.0.0.0/0 tcp spt:8080 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 0 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:53 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp spt:53 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp spt:123 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:123 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:20 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:21 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:80 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:88 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:8000 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:8080 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:8888 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:873 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:6969 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:6900 ACCEPT tcp -- 61.172.241.98 0.0.0.0/0 ACCEPT tcp -- 61.172.247.98 0.0.0.0/0 ACCEPT tcp -- 61.172.247.100 0.0.0.0/0 ACCEPT tcp -- 61.152.122.33 0.0.0.0/0 ACCEPT tcp -- 61.152.110.130 0.0.0.0/0 ACCEPT tcp -- 210.51.28.220 0.0.0.0/0 ACCEPT tcp -- 210.51.28.120 0.0.0.0/0 ACCEPT tcp -- 61.172.241.120 0.0.0.0/0 ACCEPT tcp -- 211.147.0.85 0.0.0.0/0 ACCEPT tcp -- 211.147.0.114 0.0.0.0/0 ACCEPT tcp -- 222.73.61.249 0.0.0.0/0 ACCEPT tcp -- 222.73.61.250 0.0.0.0/0 ACCEPT tcp -- 222.73.61.251 0.0.0.0/0 ACCEPT tcp -- 210.51.31.11 0.0.0.0/0 tcp dpt:38422 ACCEPT tcp -- 210.51.31.12 0.0.0.0/0 tcp dpt:38422 ACCEPT tcp -- 61.172.254.123 0.0.0.0/0 tcp spt:8080 ACCEPT tcp -- 61.172.251.109 0.0.0.0/0 tcp spt:8080 ACCEPT tcp -- 61.172.247.85 0.0.0.0/0 ACCEPT tcp -- 222.73.12.248 0.0.0.0/0 ACCEPT tcp -- 61.172.254.184 0.0.0.0/0 ACCEPT tcp -- 61.172.254.78 0.0.0.0/0 ACCEPT tcp -- 61.172.254.243 0.0.0.0/0 ACCEPT tcp -- 61.152.97.115 0.0.0.0/0 ACCEPT tcp -- 221.231.128.206 0.0.0.0/0 ACCEPT tcp -- 221.231.130.199 0.0.0.0/0 ACCEPT udp -- 172.0.0.0/8 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 10.0.0.0/8 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 192.168.0.0/16 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 61.172.252.58 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 61.183.13.201 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 222.73.2.11 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 221.208.157.158 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 218.30.74.250 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 202.102.54.234 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 125.64.2.115 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 222.73.23.23 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 210.51.33.97 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 210.51.33.98 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 222.73.11.112 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 222.73.11.111 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 222.73.11.89 0.0.0.0/0 udp spt:38514 DROP tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:38423 REJECT tcp -- 0.0.0.0/0 0.0.0.0/0 reject-with tcp-reset DROP all -- 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT) target prot opt source destination DROP all -- 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- 0.0.0.0/0 222.73.11.89 udp dpt:38514

  Read the article

• TFTP uploads failing

  - by dunxd

  I am running TFTPD via xinetd on a Centos 5.4 server. I am able to access files via tftp fine, so I know the service is running ok. However, whenever I try and upload a file I get a 0 Permission denied message. I have already created the file in /tftpboot and set the permissions to 666. My tftpd config has verbose logging (-vvvv), but all I see in my /var/log/messages is: START: tftp pid=20383 from=192.168.77.4 I have seen some mention that SELinux can prevent TFTPD uploads, but I'd expect to see something in the logs. I have SELinux set in permissive mode. Any ideas?

  Read the article

• Cygwin Python and Windows Ruby

  - by Cheezo

  I have a peculiar setup as follows: I have cygwin installed on a Windows 7 machine. I need execute a python script setup in cygwin from the windows CLI. This works fine : c:\cygwin\bin\python2.6.exe c:\cygwin\bin\python-script This python-script accesses a file: ~/.some_config_file which translates to /home/user-name when i execute it from Windows as above. So this works as expected. Now, the next step is to execute this python script from ruby(which is setup on Windows natively w/o Cygwin). When i execute the script from ruby, the ~/.some_config_file translates to /cygdrive/c/Users/user-name instead of the expected /home/user-name leading to the script failing. I understand that something in the environment, PATH etc needs to be set correctly although i cannot seem to find what exactly.

  Read the article

• PXE booting LACP hosts on Force10 S50N with FTOS

  - by lolwutreddit

  Hardware: S50N Firmware: FTOS 8.4.2.6 Problem: We're trying to PXE boot some servers that are connected via port-channel interfaces with LACP. Current Work-around: we PXE boot a server with a single interface (eth0), and then use a Perl script to turn up the port-channel interfaces after the server is built. Details: Is anyone doing anything similar on Force10 S50 switches with FTOS? If not, is anyone doing this on another S series, or larger chassis-based Force10? I'm wondering if Native VLAN will solve this, since ports in a port-channel cannot explicitly have a VLAN set, and they don't seem to use the tagged or untagged VLAN that the port channel is in. I will confirm this next (I think it's the only thing I haven't tried) Juniper Example: http://broken.net/openindiana/how-to-pxe-boot-systems-on-lacp-using-juniper-switches/ Cisco: there are plenty of documented ways to solve this issue on IOS and Nexus Update/Edit: since there seems to be no way to use interface or port-channel mode commands to get the individual interfaces to show up in spanning-tree (rtsp in this case), the ports should never go into a forwarding state. I'm not going to mess with it anymore unless a) someone that has experience passes it on, or b) Force10 comes up with a solution for this (I'm guessing it will only be introduced on other S platforms (S55, S60), since the S50 seems to be near EOL). I'm basing that on the fact that the Open Automation type features are only being supported on the newer switches.

  Read the article

• kmemsize problems in VPS even when there is about 500MB free mem

  - by Amer

  Hello, I have a site hosted on a Plesk VPS with 512MB memory and keep on getting kmemsize in "black zone" QoS errors. The soft limit of kmemsize is 12,288,832 and hard limit is 13,517,715. The definition Virtuozzo gives is: Size of unswappable memory, allocated by the operating system kernel. What's eating up the kmemsize? Is there any way to reconfigure and increase the kmemsize? The servers barely have any load or processing. Thanks for the help...

  Read the article

• xorg version in centos 5.4

  - by sanjan

  Hi what is the release version of Xorg in CentOs 5.4? can somebody do a 'Xorg -version' and paste the output here. Thanks.

  Read the article

• Google images sometimes terribly slow when using dnsmasq

  - by Joril

  Hi everyone! I am the admin of a small LAN of 10+ computers. I've set up a dnsmasq server for DHCP and DNS resolution, and it's working almost fine.. My problem is that when I try to use Google images, sometimes it takes ages to show the actual images. I get just the textual part of the page (menus and so on) while the images themselves are shown as the still-loading-white boxes.. When I use the DSL router directly as DNS, the site works fine all the time. The problem sometimes presents itself with Google maps too.. The map takes ages to load. Any idea on what I could try to troubleshoot this? (dnsmasq 2.47 on CentOS 5.2 64bit, our outside connection is an asymmetrical 4Mbps DSL)

  Read the article

• Google images sometimes terribly slow when using dnsmasq

  - by Joril

  Hi everyone! I am the admin of a small LAN of 10+ computers. I've set up a dnsmasq server for DHCP and DNS resolution, and it's working almost fine.. My problem is that when I try to use Google images, sometimes it takes ages to show the actual images. I get just the textual part of the page (menus and so on) while the images themselves are shown as the still-loading-white boxes.. When I use the DSL router directly as DNS, the site works fine all the time. The problem sometimes presents itself with Google maps too.. The map takes ages to load. Any idea on what I could try to troubleshoot this? (dnsmasq 2.47 on CentOS 5.2 64bit, our outside connection is an asymmetrical 4Mbps DSL)

  Read the article

• CentOS will not boot. Error 13

  - by ipengineer

  I am having trouble with one of our CentOS servers. I migrated this server to XenServer, installed a new xen kernel, and performed a mkinitrd with: mkinitrd --omit-scsi-modules --with=xennet --with=xenblk --preload=xenblk initrd-2.6.18-308.4.1.el5xen-no-scsi.img 2.6.18-308.4.1.el5xen Now I am getting an error 13 on boot. Screenshot: http://postimage.org/image/k7js0l41v/ I can still boot with the PAE kernel. Does anyone have any idea on how to resolve this? My Grub file looks like: default=0 timeout=5 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title CentOS (2.6.18-308.4.1.el5xen) root (hd0,0) kernel /vmlinuz-2.6.18-308.4.1.el5xen ro root=/dev/hdb1 ramdisk_size=256000 initrd /initrd-2.6.18-308.4.1.el5xen-no-scsi.img title CentOS (2.6.18-308.4.1.el5PAE) root (hd0,0) kernel /vmlinuz-2.6.18-308.4.1.el5PAE ro root=/dev/hdb1 ramdisk_size=256000 initrd /initrd-2.6.18-308.4.1.el5PAE.img title CentOS (2.6.18-274.17.1.el5PAE) root (hd0,0) kernel /vmlinuz-2.6.18-274.17.1.el5PAE ro root=/dev/hdb1 ramdisk_size=256000 initrd /initrd-2.6.18-274.17.1.el5PAE.img

  Read the article

• Stack , data and address space limits on an Ubuntu server

  - by PaulDaviesC

  I am running an Ubuntu server which has around 5000 users. The users are allowed to SSH in to the system. So in order to cap the memory used up by a process I have capped the address space limits using limits.conf. So my question is , should I be limiting the data and stack ? I feel that is not required since I am capping address space. Are there any pitfalls if I do not cap the stack and data limits?

  Read the article

• KVM-Guests can't get past bridge - no internet connection

  - by tmn29a

  I'm running a backported KVM on a Debian Squeeze. ATM the KVM-Guest can't connect to the internet through the bridge I have set up. The guests can reach each other, the host but nothing outside. I can neither ping, nslookup or do anything to a remote address. The guest are configured to have a static IP. When I didn;t have the bridge but a virtual bridge (the KVM-default) the guest could connect fine. After setting up the bridge things broke, so I think the problem lies there. # The loopback network interface auto lo br0 iface lo inet loopback # Bonding Interface auto bond0 iface bond0 inet static address 10.XXX.XXX.84 netmask 255.255.255.192 network 10.XXX.XXX.64 gateway 10.XXX.XXX.65 slaves eth0 eth1 bond_mode active-backup bond_miimon 100 bond_downdelay 200 bond_updelay 200 iface br0 inet static bridge_ports eth0 eth1 address 172.xxx.xxx.65 broadcast 172.xxx.xxx.127 netmask 255.255.255.192 gateway 172.xxx.xxx.65 bridge_stp on bridge_maxwait 0 Thanks in advance for your help !

  Read the article

• Correct way to treat iptables init failure?

  - by chris_l

  Hi, I'm initializing my iptables rules via /etc/network/if-pre-up.d/iptables, using iptables-restore. This works fine, but I'm a bit worried about what would happen, if that script failed for some reason (maybe the saved iptables file is corrupt or whatever). In case the script failed, I'd like to: Start up my network interfaces without any iptables rules Start up OpenSSH server But not any other services like web server, ... (and maybe stop running instances) Is there a good canonical way to do that? Going into a lower init stage? - I haven't done that in a long time, and I think a lot about init has changed in recent years (?) - which stage should I drop to, and would the OpenSSH server and my network interfaces still run? Thanks Chris (On Debian Lenny)

  Read the article

• Run script before shutdown/restart

  - by dtbarne

  I'd like to run a PHP script when an instance is told to shutdown, but of course before it actually finishes shutting down. My particular script is just looking to push some log files from the local partition to a another server. I've got the gist of how this process works, but I need some clarification. How I understand it. Please correct me if I'm wrong. Create an executable script in /etc/init.d (lets call it /etc/init.d/push-logs) Create a symlink to /etc/init.d/push-logs from /etc/rc0.d (shutdown) and /etc/rc6.d (reboot). The name should be KXXpush-logs Here's my questions: Of course - am I understanding correctly? For #2 above - it sounds like the lower the XX the better - is there too low a number I can use? Does it matter if it shares a number with another script? Does the script in /etc/init.d/push-logs HAVE to follow the standard init.d template (supporting start/stop, etc. commands)? This doesn't really apply to my use case. If possible I just want the script to be the following: #!/bin/sh # # Run PHP file prior to shutdown # /usr/bin/php /path/to/php_file.php

  Read the article

• Can connect to Samba server but cannot access shares?

  - by jlego

  I have setup a stand-alone box running Fedora 16 to use as a file-sharing and web development server. Needs to be able to share files with a PC running Windows 7 and a Mac running OSX Snow Leopard. I've setup Samba using the Samba configuration GUI tool. Added users to Fedora and connected them as Samba users (which are the same as the Windows and Mac usernames and passwords). The workgroup name is the same as the Windows workgroup. Authentication is set to User. I've allowed Samba and Samba client through the firewall and set the ethernet to a trusted port in the firewall. Both the Windows and Mac machines can connect to the server and view the shares, however when trying to access the shares, Windows throws error 0x80070035 " Windows cannot access \SERVERNAME\ShareName." Windows user is not prompted for a username or password when accessing the server (found under "Network Places"). This also happens when connecting with the IP rather than the server name. The Mac can also connect to the server and see the shares but when choosing a share gives the error "The original item for ShareName cannot be found." When connecting via IP, the Mac user is prompted for username and password, which when authenticated gives a list of shares, however when choosing a share to connect to, the error is displayed and the user cannot access the share. Since both machines are acting similarly when trying to access the shares, I assume it is an issue with how Samba is configured. smb.conf: [global] workgroup = workgroup server string = Server log file = /var/log/samba/log.%m max log size = 50 security = user load printers = yes cups options = raw printcap name = lpstat printing = cups [homes] comment = Home Directories browseable = no writable = yes [printers] comment = All Printers path = /var/spool/samba browseable = yes printable = yes [FileServ] comment = FileShare path = /media/FileServ read only = no browseable = yes valid users = user1, user2 [webdev] comment = Web development path = /var/www/html/webdev read only = no browseable = yes valid users = user1 How do I get samba sharing working? UPDATE: Before this box I had another box with the same version of fedora installed (16) and samba working for these same computers. I started up the old machine and copied the smb.conf file from the old machine to the new one (editing the share definitions for the new shares of course) and I still get the same errors on both client machines. The only difference in environment is the hardware and the router. On the old machine the router received a dynamic public IP and assigned dynamic private IPs to each device on the network while the new machine is connected to a router that has a static public IP (still dynamic internal IPs though.) Could either one of these be affecting Samba? UPDATE 2: As the directory I am trying to share is actually an entire internal disk, I have tried to things: 1.) changing the owner of the mounted disk from root to my user (which is the same username as on the Windows machine) 2.) made a share that only included one of the folders on the disk instead of the entire disk with my user again as the owner. Both tests failed giving me the same errors regarding the network address. UPDATE 3: Not sure exactly what I did, but now whenever I try to connect to the share on the Windows 7 client I am prompted for my username and password. When I enter the correct credentials I get an access denied message. However I did notice that under the login box "domain: WINDOWS-PC-NAME" is listed. I believe this could very well be the problem. Any suggestions? UPDATE 4: So I've completely reinstalled Fedora and Samba now. I've created a share on the first harddrive (one fedora is installed on) and I can access that fine from Windows. However when I try to share any data on the second disk, I am receiving the same error. This I believe is the problem. I think I need to change some things in fstab or fdisk or something. UPDATE 5: So in fstab I mapped the drive to automount in a folder which works correctly. I also added the samba_share_t SElinux label to the mountpoint directory which now allows me to access the shares on the Windows machine, however I cannot see any of the files in the directory on the windows machine. (They are there, I can see them in the fedora file browser locally) UPDATE 6: Figured it out. See answer below

  Read the article

• What is the best distro to host a KVM virtualization solution

  - by elventear

  I am looking for a Server oriented distro that we can expect have decent support but also offer as much as possible some of the latest features that KVM might offer. I am leaning towards Ubuntu LTS 10.04, because well it's LTS and more bleeding edge, but I find Ubuntu not serious enough in terms of support (I say this a heavy Ubuntu user). Given that Centos 6 is not out yet, I am not sure if going Centos 5 would be the best option in terms of getting more features from KVM. Any other distro you would recommend that could meet the criteria of long term support? (At least 4 years)

  Read the article

• Storage subsystem borking after server restart (all on a Parallel SCSI bus)

  - by Dat Chu

  I have a server (with a SCSI HBA) connected to two Promise VTrak M310p RAID enclosure on the same bus. Everything is working fine until I have to restart my server. Once restarted, the server can no longer communicate with the enclosures: lots of read errors and bus resets. I have to turn off both enclosure, then turn off the server, then turn on the enclosure, then turn on the server for things to work. I don't believe this is the normal behavior, what could I be missing?

  Read the article

• Getting an error when mounting LVM snapshot

  - by Sandra

  I have migrated a file based Xen guest to LVM using dd bs=1M if=/dev/zero of=/dev/vg00/vm10 qemu-img convert ~/vm10.qcow2 -O raw /dev/vg00/vm10 and changed the Xen domain file for the VM to use the LV instead of the old file. The VM boots up, and now on the Xen host would I like to make a snapshot of the running VM. # lvcreate --size 10G --snapshot --name vm10-snapshot /dev/vg00/vm10 Logical volume "vm10-snapshot" created # mount /dev/vg00/vm10-snapshot /mnt/snapshot/ mount: you must specify the filesystem type # dmesg |tail EXT3 FS on dm-3, internal journal EXT3-fs: mounted filesystem with ordered data mode. hfs: unable to find HFS+ superblock VFS: Can't find ext3 filesystem on dev dm-4. hfs: unable to find HFS+ superblock hfs: unable to find HFS+ superblock VFS: Can't find ext3 filesystem on dev dm-2. hfs: unable to find HFS+ superblock hfs: unable to find HFS+ superblock hfs: unable to find HFS+ superblock For some reason it can't see it is an EXT3 filesystem. I have also tried to mount with -t ext3, but still didn't mount. # lvdisplay --- Logical volume --- LV Name /dev/vg00/vm10 VG Name vg00 LV UUID I1y1vQ-Bac5-5jwW-melh-TY5h-l9NO-qaelKk LV Write Access read/write LV snapshot status source of /dev/vg00/vm10-snapshot [active] LV Status available # open 2 LV Size 8.00 GB Current LE 2048 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:2 --- Logical volume --- LV Name /dev/vg00/vm10-snapshot VG Name vg00 LV UUID GWsOx3-TPpr-GW64-uiMz-u1YN-QU4h-l0Kala LV Write Access read/write LV snapshot status active destination for /dev/vg00/vm10 LV Status available # open 0 LV Size 8.00 GB Current LE 2048 COW-table size 10.00 GB COW-table LE 2560 Allocated to snapshot 0.00% Snapshot chunk size 4.00 KB Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:4 # What could the problem be?

  Read the article

• Is there a way to change the GTK theme for applications run as superuser on KDE?

  - by Patches

  When I run GTK applications on KDE, they use the QtCurve theme that matches my color and font scheme as configured in the KDE System Settings application. However GTK applications run as superuser use the old default GNOME, regardless of whether I run them with kdesudo, gksudo, or sudo on a terminal. For example, here's gedit run as superuser on top, and under my normal user account on the bottom: Strangely, KDE applications run with kdesudo display the default Oxygen styling but use my settings when run with sudo on a terminal. Is there any way to configure the stying GTK applications use when run as superuser on KDE?

  Read the article

• If I'm a web server, for which accounts can I turn off shells within passwd file?

  - by eric01

  I am making a web server running LAMP and want to access it using SSH. When I open the passwd file, I see all those accounts and I want to know for which ones I can put false. I have the following accounts: root, daemon, bin, sys, sync, games, man, lp, mail, news, uucp, proxy, www-data backup, list, irc, gnats, nobody, libuuid, syslog, messagebus, whoopsie, mandscape, sshd, eric Except root, sshd and eric, which ones should I not disable? How about www-data and sshd? Thanks a lot for your help.

  Read the article

• multiple php compiler on single apache installation

  - by getmizanur

  elloo, i have some old php scripts which runs on php-5.2.x and the current server has php-5.3.x. to get around this problem,i have got two options one is to downgrade php-5.3.x or install php-5.2.x and php-5.3.x at the same time where php-5.2.x serve cgi script. i have decided go for the second option i have followed this tutorial and i can get most of it working however except execution of shell script which selects php-cgi version. i cannot get apache to execute this script. how do i get apache to execute #!/bin/sh # you can change the PHP version here. version="5.2.6" # php.ini file location, */php-5.2.6/lib equals */php-5.2.6/lib/php.ini. PHPRC=/etc/php/phpfarm/inst/php-${version}/lib/php.ini export PHPRC PHP_FCGI_CHILDREN=3 export PHP_FCGI_CHILDREN PHP_FCGI_MAX_REQUESTS=5000 export PHP_FCGI_MAX_REQUESTS # which php-cgi binary to execute exec /etc/php/phpfarm/inst/php-${version}/bin/php-cgi my apache vhost.conf <VirtualHost *:80> ServerName 526.localhost DocumentRoot /home/getmizanur/public_html/www <Directory "/home/getmizanur/public_html/www"> AddHandler php-cgi .php Action php-cgi /php-fcgi/php-cgi-5.2.6 </Directory> </VirtualHost> can some one tell me what am i doing wrong? thanks in advance. solution: if i did a2dismod php5 then the above configuration worked. when a2enmod php5 had been activated, apache was executing php5.3 instead of php5.2 even after telling apache to execute php5.2 shell script. to solve my problem, i had to change my virtualhost configuration <VirtualHost *:80> ServerName 526.localhost DocumentRoot /home/getmizanur/public_html/www DirectoryIndex index.php <Directory "/home/getmizanur/public_html/www"> AddHandler php-cgi .php Action php-cgi /php-fcgi/php-cgi-5.2.6 <FilesMatch "\.php"> SetHandler php-cgi </FilesMatch> </Directory> </VirtualHost> presto, it started working.

  Read the article

• Xen dom0 reports incorrect amount of RAM with dom0_mem set

  - by xen_amnesiac

  I've done a fair bit of searching about this, but have found nothing that answers my question. I have a system with 6GB of RAM which acts as a Xen server. For reference, it runs Ubuntu 12.04. I've set the kernel parameter dom0_mem:512M,max:512M in /etc/default/grub as follows: GRUB_CMDLINE_XEN_DEFAULT="dom0_mem=min:512M,max:512M" I've tried variations of that, with the same result. My question is this: With the above set, the dom0 reports in all applications a RAM amount of 422M. cat /proc/meminfo gives the following: $ cat /proc/meminfo MemTotal: 432472 kB MemFree: 54144 kB Buffers: 17640 kB Cached: 220104 kB SwapCached: 30172 kB Active: 136500 kB Inactive: 167780 kB Active(anon): 6156 kB Inactive(anon): 60516 kB Active(file): 130344 kB Inactive(file): 107264 kB Unevictable: 52 kB Mlocked: 52 kB SwapTotal: 1794044 kB SwapFree: 1682012 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 39572 kB Mapped: 8048 kB Shmem: 136 kB Slab: 44324 kB SReclaimable: 22012 kB SUnreclaim: 22312 kB KernelStack: 1280 kB PageTables: 3840 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 2010280 kB Committed_AS: 329192 kB VmallocTotal: 34359738367 kB VmallocUsed: 313988 kB VmallocChunk: 34359417340 kB HardwareCorrupted: 0 kB AnonHugePages: 0 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 524696 kB DirectMap2M: 0 kB top, htop, free -m, and byobu's RAM monitor all report the same amount. At first I thought this was because of the onboard graphics borrowing some memory, but have now switched to a dedicated GPU and it persists. Is this normal behavior, or has something gone amiss? It's just about 100MB of RAM that's "gone", and I have no idea where it went. I understand that it's normal that not all RAM is available for allocation, but does the system really take an amount relatively high to the amount of RAM available?

  Read the article

• Selinux interfering with vboxwebsrv or phpvirtualbox

  - by Mike W

  I have a brand new installation of Fedora 18, with a brand new installation of Virtualbox 4.2. I have spent a painful few hours trying to get phpVirtualBox working. Apache 2.4 and PHP 5.4 are installed, along with the phpVirtualBox software. Attempting to access phpVirtualBox allowed me to login, but then I'd have a prolonged wait until an 'Error fetching HTTP headers' message appeared. Finally, I set SeLinux to permissive, and Bingo! things start to work. For some reason the SeLinux Troubleshooter isn't flagging any messages from SeLinux, I don't know what to look for now. This is a development box so I could leave SeLinux set to permissive but I will need to make this work in anger on the next project. My question, then, is this: What changes to SeLinux policies do I need to make to allow phpVirtualBox and vboxwebsrv to work together? If there's more information I can post that will assist I'll gladly post it - just let me know what it is.

  Read the article

< Previous Page | 442 443 444 445 446 447 448 449 450 451 452 453  | Next Page >