Search Results

Search found 22874 results on 915 pages for 'hidden network'.

Page 453/915 | < Previous Page | 449 450 451 452 453 454 455 456 457 458 459 460  | Next Page >

• VLAN Tagging Traffic on Cisco Switch

  - by David W

  I have a situation where I'm setting up multiple VLANS on a pfSense firewall on the same physical interface for a client. So in pfSense, I now have VLAN 100 (employees) and VLAN 200 (students - student computer lab). Downstream from pfSense, I have a Cisco SG200 switch, and coming off of the SG200 is the student lab (running on a Catalyst 2950. Yes, that's old, but it works, and this is a poor nonprofit we're talking about). What I'd like to do is tag everything on the network as VLAN 100, except for the student computer lab. Earlier today when I was on-site with the client, I went into to the old Catalyst 2950, and assigned all of its ports to access VLAN 200 (switchport mode access vlan 200) without setting up a trunk on the Catalyst or on the SG200. Looking back on it, I now understand why internet in the lab broke. I reverted the lab back to the default VLAN1 (we're still running on a different firewall - we haven't deployed pfSense -, and the traffic is still separated physically). So my question is, what do I need to do in order to properly deploy this scenario? I believe the correct answer is: Ensure VLANs 100 and 200 are setup in pfSense, and that DHCP is operating correctly (on separate subnets) Setup a trunkport VLAN that allows both 100 & 200 traffic, and plug that port directly into pfSense. Setup a VLAN 200 trunkport on the SG200 (It's not running iOS, but if it were, the command would be switchport trunk native vlan 200), which will then plug into the Catalyst 2950. Setup a VLAN 200 trunkport on the Catalyst 2950 (that is plugged into the SG200 VLAN200 port with the same command - switchport trunk native vlan 200) Setup the rest of the ports on the old Catalyst 2950 in the lab to be access ports on VLAN200. Is there anything that I'm missing, or do I need to tweak any of these steps, in order to properly segment the network traffic?

  Read the article

• EXCEL workbook, intermitently, takes 30 seconds to load

  - by Julio Nobre

  I am trying to figure out why a simple .XLS EXCEL workbook is taking, randomly, 30 seconds to open. Before answering: Please, bear mind the following: Problem symptoms Hanging is intermitent and it takes exactly 30 seconds; During hanging there is no cpu or disk activity; It only happens during workbook load. Every runs smooth after that; Windows Explorer.exe hangs on folder, but all other folders, system and applications are still responsive; There are no consecutive hangings. I have to wait for while to reproduce this behaviour; All workbooks where located on a local drive (C:\BPI); The workbook has no macros and no addins; Office 2003 is being used for several years; The computer is running Windows XP; Computer has several network mapped drives, all addressed to main file server; Recently, main fileserver was replaced by Windows 2011 SBS Standard Edition What I have done so far I have traced machine Explorer.exe, using Process Monitor, added Duration column, and filtered by Duration 1. That's is how I found that hanging was taking exactly 30 seconds. For further information, please refer to Oliver Salzburg tutorial. Using Process Monitor, I have also figured out than five operations were taking most of sample collecting duration. Looking at sample image below, column Operation below you will notice that one single operation was taking 29 seconds; I have tried different workbooks (all of them smaller than 30 KB); I have, temporarily, removed all shortcuts on User Document's folder that were pointing to network drives or shares; I have runned CCleaner to fix registry issues; I made sure that there were no external links on tested workbooks; I have reproduced this behaviour for hours; I have extensivelly researched for hours on the web; Process Monitor's collected and filtered data

  Read the article

• Cannot Connect To VMWare Guest OS Using Either RDP or VNC

  - by Humanier

  I have a PC (Windows XP SP3) with VMWare Workstation 7 installed. The VMWare hosts Windows Server 2003 Enterprise Edition R2. RealVNC (4.1.3) is installed on both OS'es. Both of them use Hamachi2. Host OS (WinXP) also runs ZoneAlarm Firewall. Hamachi network is set as trusted. My goal is to allow RDP and VNC connections to be made to the guest OS (Windows Server 2003). Both options work absolutely fine if I connect from the host OS. However I have problems when other computers from our Hamachi network try to connect the guest OS (Win2K3). RDP connections. RDP window opens, shows black content and after 15-20 seconds displays following error: RealVCN connections. Users are able to connect but all they see is a black screen inside VNC window. At the same their input (keystrokes or mouse moves/clicks) are visible when looking at the console window of the Win2K3. I really appreciate any ideas on how to resolve the mentioned problems.

  Read the article

• How does Tunlr work?

  - by gravyface

  For those of you not in the US, Tunlr uses DNS witchcraft to allow you to access US-only (and UK-only stuff like BBC radio online) services and Websites like Hulu.com, etc. without using traditional methods like a VPN or Web proxy. From their FAQ: Tunlr does not provide a virtual private network (VPN). Tunlr is a DNS (domain name system) unblocking service. We’re using sophisticated technologies (a.k.a. the Tunlr Secret Sauce ©) to re-adress certain data envelopes, tricking the receiver into thinking the envelope originated from within the U.S. For these data envelopes, Tunlr is transparently creating a network tunnel from your location to our U.S.-based servers. Any data that’s not directly related to the video or music content providers which Tunlr supports is not only left untouched, it’s also not even routed through Tunlr. In order to use Tunlr, you will have to change the DNS address. See Get started for more information. I can't really wrap my head around how this works; I have always assumed that these services performed a geolocation lookup via your client IP. Just really curious as to how this works. EDIT 2 I believe they're only proxying the initial geo check and then modifying the data stream request to include your real IP address so that the streaming is direct, not proxied.

  Read the article

• VPN on a ubuntu server limited to certain ips

  - by Hultner

  I got an server running Ubuntu Server 9.10 and I need access to it and other parts of my network sometimes when not at home. There's two places I need to access the VPN from. One of the places to an static IP and the other got an dynamic but with DynDNS setup so I can always get the current IP if I want to. Now when it comes to servers people call me kinda paranoid but security is always my number one priority and I never like to allow access to the server outside the network therefor I have two things I have to have on this VPN. One it shouldn't be accessiable from any other IP then these 2 and two it has to use a very secure key so it will be virtually impossible to bruteforce even from the said IP´s. I have no experience what so ever in setting up VPNs, I have used SSH tunneling but never an actuall VPN. So what would be the best, most stable, safest and performance effiecent way to set this up on a Ubuntu Server? Is it possible or should I just set up some kind of SSH Tunnel instead? Thanks on beforehand for answers.

  Read the article

• Fedora 15: em1 recently dissapeared and hostapd no longer serves internet to wirelessly connected devices

  - by Daniel K

  I have a laptop running hostapd, phpd, and mysql. This laptop uses an Ethernet connection to connect to the internet and acts as a wireless access point for my workplace's wifi devices. After installing some software and reconnecting my Ethernet elsewhere, my "em1" device is no longer present and wirelessly connected devices can no longer reach the internet. The software I recently installed is: pptp, pptpd, and updated some fedora libraries. I have also recently moved my desk and laptop to another location and thus had to reconnect the Ethernet elsewhere. Wifi devices no longer have access to the internet. Wirelessly connected devices are able to successfully log into the laptop, showing full strength, correct SSID, and uses the proper password. However, when I tried to connect to a site like google, the request times out. The device "em1" also no longer appears on my machine. Running: # ifup em1 will give me the following output: ERROR : [/etc/sysconfig/network-scripts/ifup-eth] Device em1 does not seem to be present, delaying initialization. And running: # dhclient em1 has the following output: Cannot find device "em1" When I run # dmesg|grep renamed, I get the following: renamed network interface eth0 to p4p1. I've tried to connect to the internet through p4p1 directly from the laptop and was successful. However, my wireless devices connected to my laptop are not able to connect to the internet. I have uninstalled pptp and pptpd using # yum erase ... but the problem still persists. To install pptp I used: # yum install pptp To install pptpd I did the following: # rpm -Uvh http://poptop.sourceforge.net/yum/stable/fc15/pptp-release-current.noarch.rpm # yum install pptpd To update my fedora libraries I used: # yum check-update # yum update EDIT: Running # route produces the following results: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.11.200.1 0.0.0.0 UG 0 0 0 p4p1 10.11.200.0 * 255.255.252.0 U 0 0 0 p4p1 172.16.100.0 * 255.255.255.0 U 0 0 0 wlan0

  Read the article

• After connecting wlan0 to bridge interface (and then removing it), can't connect to AP

  - by gmonk

  I'm on a laptop running Debian Jessie with kernel 3.13-1-amd64; lspci shows that my wireless NIC + driver is 04:00.0 Network controller: Intel Corporation Wireless 3160 (rev 83) Subsystem: Intel Corporation Dual Band Wireless-AC 3160 Kernel driver in use: iwlwifi This has been working without any problems, until I tried creating a bridge for lxc containers to use. I did the same thing as this person here: How-to set up a network bridge on a laptop for LXC use? -- and ended up having the same problem as this poster did, so I decided to "undo" my actions. This hasn't been successful. Actions taken so far: To configure the bridge: #> ip link add type veth #> iw dev wlan0 set 4addr on #> ifconfig veth0 up #> brctl addbr br0 #> brctl addif br0 wlan0 #> brctl addif br0 veth0 #> ifconfig br0 192.168.0.4/24 #> ifconfig wlan0 0.0.0.0 To "deconfigure": #> brctl delif br0 wlan0 #> brctl delif br0 veth0 #> iw dev wlan0 set 4addr off #> ifconfig veth0 down #> ifconfig wlan0 down #> ifconfig br0 down #> brctl delbr br0 Now, dmesg and /var/log/syslog show repeated attempts at connecting to the AP that was working before, which fail after authentication: May 27 09:16:01 myhostname kernel: [11350.757172] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:01 myhostname kernel: [11350.759036] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:01 myhostname kernel: [11350.762615] wlan0: authenticated May 27 09:16:01 myhostname kernel: [11350.762753] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.762755] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.765080] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:01 myhostname kernel: [11350.767474] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:01 myhostname kernel: [11350.767476] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:01 myhostname kernel: [11350.788475] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:02 myhostname dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 14 May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname kernel: [11354.559579] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.561458] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> associating May 27 09:16:04 myhostname kernel: [11354.563445] wlan0: authenticated May 27 09:16:04 myhostname kernel: [11354.563631] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.563633] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.565727] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.568091] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:04 myhostname kernel: [11354.569030] wlan0: associated May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:05 myhostname kernel: [11354.978204] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:05 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:05 myhostname kernel: [11354.992729] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:05 myhostname kernel: [11354.995004] cfg80211: World regulatory domain updated: May 27 09:16:05 myhostname kernel: [11354.995005] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:05 myhostname kernel: [11354.995006] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995008] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995009] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995010] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.763968] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:09 myhostname kernel: [11358.765796] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.769957] wlan0: authenticated May 27 09:16:09 myhostname kernel: [11358.770102] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770104] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770846] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname kernel: [11358.773358] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:09 myhostname kernel: [11358.773361] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:09 myhostname kernel: [11358.802187] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.573442] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.575270] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.580334] wlan0: authenticated May 27 09:16:12 myhostname kernel: [11362.580503] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.580516] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.583508] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.585908] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:12 myhostname kernel: [11362.586781] wlan0: associated May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:13 myhostname kernel: [11362.947693] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:13 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:13 myhostname kernel: [11362.973461] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:13 myhostname kernel: [11362.975673] cfg80211: World regulatory domain updated: May 27 09:16:13 myhostname kernel: [11362.975675] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:13 myhostname kernel: [11362.975676] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975677] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0/wireless): association took too long. May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: config -> failed (reason 'no-secrets') [50 120 7] May 27 09:16:14 myhostname NetworkManager[13992]: <info> Marking connection 'Auto myaccesspoint' invalid. May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0) failed for connection 'Auto myaccesspoint' May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: failed -> disconnected (reason 'none') [120 30 0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): deactivating device (reason 'none') [0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> disconnected The things that jump out at me are "deauthenticating ... by local choice( reason=3)" and the lines that contain "(reason=15)". I've tried various fixes: iwconfig wlan0 power off killing wpa_supplicant connecting with iwconfig + dhclient instead of gnome's network -manager explicitly configuring wlan0 in /etc/network/interfaces creating a /etc/wpa_supplicant.conf file ...but nothing seems to work. I'm not sure what I did wrong, or what step I've skipped in trying to get wlan0 back as a non-bridged device -- I removed it from the bridge and then deleted the bridge itself. Any ideas?

  Read the article

• Unable to connect to FTP - Connection timeout after MLSD

  - by Afrosimon

  So here is my problem, I'm absolutely unable to connect to a FTP server, in circumstances I've never seen before. Here is the situation : I get a "Connection timed out" just after the MLSD command. I usually use Filezilla, under Ubuntu, but to make sure the problem isn't related to this particular client I tried a few others : gftp on ubuntu and winscp and freeftp on windows 7. All the same result. Also made sure to try with Active or Passive modes. Same result. At this point I would be inclined to think there is something wrong with my current network (furthermore, according to a coworker the FTP server is OK). But I did check with http://ftptest.net/ and I am able to get the directory listing (which I'm not able to through a FTP client). So in the end the last thing I didn't tried is to go on another network, solution which seems would work, but wouldn't be very practical in the long run. And thus I guess there's something wrong with my router... but what could it possibly be? Note : I did try to register and post this question on filezilla's board first... but I can't create an account with a gmail nor hotmail account. WTF?

  Read the article

• Default IPv6 route on debian squeeze does not come up after boot

  - by Georg Bretschneider

  I have a problem with my default IPv6 route not coming up after boot on a Debian Squeeze system. This is my config (/etc/network/interfaces): # Loopback device: auto lo iface lo inet loopback iface lo inet6 loopback # device: br0 auto br0 iface br0 inet static bridge_ports eth0 bridge_fd 0 address 88.198.62.xx broadcast 88.198.62.63 netmask 255.255.255.224 gateway 88.198.62.33 up route add -net 88.198.62.32 netmask 255.255.255.224 gw 88.198.62.33 br0 iface br0 inet6 static address 2a01:4f8:131:10x::2 netmask 64 gateway 2a01:4f8:131:100::1 up route -A inet6 add 2a01:4f8:131:100::1/59 dev br0 My inet comes up alright, but I have to exec the route command manually after boot to make IPv6 work. Otherwise I can't even reach my gateway. This is the output of ip -6 route show after boot: 2a01:4f8:131:10x::/64 dev br0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 unreachable fe80::/64 dev lo proto kernel metric 256 error -101 mtu 16436 advmss 16376 hoplimit 4294967295 fe80::/64 dev br0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 I already tried it with: up ip -6 route add 2a01:4f8:131:100::1 dev br0 up ip -6 route add default via 2a01:4f8:131:100::1 dev br0 in /etc/network/interfaces, but with the same results. If I execute those commands manually on my shell, everything starts working nicely. And yes, I tried with post-up instead of up, too. Only other changes I made was to activate ip forwarding for IPv6, because I want to run some LXC containers on that system.

  Read the article

• Win Svr 2003 DHCP Bad Addresses

  - by VinceM

  After looking at other posts I still can figure this out. I'll start at the beginning... I inherited this network and I'm not the most knowledgeable about networking... We have a AD DHCP Server that is also our DNS server, We were having some VPN issues (on the same server) and my boss decided to disable routing and remote access, which cleared the settings. We couldn't get it set back up correctly so we rolled back to a backup drive they created a number of months ago. Since rolling back I've had Bad_Address listings in DHCP and there is a number of duplicate records in the DNS Forward Lookup Zones. We have less than 50 devices on the network but I have over 90 Bad Addresses showing. This server is currently running but we get IP address conflicts all the time on pretty much all the computers. I have had people do release and renew but it didn't help... I have also deleted and re-added the scope to no avail either. Any help or ideas would be greatly appreciated and I apologize if I missed another post that has information to help. Thanks, Vince

  Read the article

• I get "An error occurred while Windows was synchronizing with [name of time server]." when trying t

  - by ChrisF

  Prompted by the answers to this question I decided to give the Windows built in time synchronisation another go. However, no matter what time server I use I get this error: "An error occurred while Windows was synchronizing with [name of time server]." The help suggests the following as reasons for failure: You are not connected to the Internet. Establish an Internet connection before you attempt to synchronize your clock. Your personal or network firewall prevents clock synchronization. Most corporate and organizational firewalls will block time synchronization, as do some personal firewalls. Home users should read the firewall documentation for information about unblocking network time protocol (NTP). You should be able to synchronize your clock if you switch to Windows Firewall. The Internet time server is too busy or is temporarily unavailable. If this is the case, try synchronizing your clock later, or update it manually by double-clicking the clock on the taskbar. You can also try using a different time server. The time shown on your computer is too different from the current time on the Internet time server. Internet time servers might not synchronize your clock if your computer's time is off by more than 15 hours. To synchronize the time properly, ensure that the date and time settings are set close to your current time in the Date and Time Properties in Control Panel. Now the first reason is clearly wrong - I am connected to the internet. I can see the 2nd being the most likely cause. I have Sygate Personal Firewall running, but it normally asks if something it trying to connect for the first time. Does anyone know I can unblock the NTP protocol - or at least check if it is blocked?. I don't think it's #3 or #4 as I've tried a number of different servers including the one currently used by Atomic Clock Sync. Though if someone knows the address of a UK time server I can double check this.

  Read the article

• Netflix streaming stops loading at 98% on Revo 3700

  - by Martin Harris

  I'm trying to stream Netflix on an Acer Revo 3700 running Windows 7 Home Premium, but it hangs on the loading screen at 98% (after it has formatted the player to the right aspect ratio and added the controls, but before the video starts) with no error messages or failures. I have two other machines on the same network, one running Windows 7 Home Premium and another running XP, which both stream faultlessly. Things I have tried: Both a wired and wireless connection to the router Upgrading the video and audio drivers IE, Chrome and Firefox Boxee software Connecting with a VGA cable instead of HDMI (in case it is a HDCP thing) Uninstalling and reinstalling Silverlight. Getting someway into loading a HD movie and turning "Allow HD" off Does anyone know what Netflix is doing at the 98% load mark? Are there any log files? Anything else worth trying? Full disclosure: I'm using Netflix from the UK through a US based VPN. I've tried multiple VPNs and the problem is exactly the same, also the other machines on the same network through the same VPN work fine so I don't think this is the issue, but it might be a factor. The region check happens at around 7% and I get past that.

  Read the article

• libvirt's dnsmasq does not respond to dns queries or provide dhcp

  - by Jeremy

  This is on Ubuntu 10.04 server, using KVM to run Ubuntu guests. This system has been working for a long time and I have not changed anything (other than applying security updates), but today I found dnsmasq no longer responds to requests. I cannot say how long this has been broken for me because I don't frequently use the NAT'd guests. So it could have started just after the last updates or some other event and I just now found it. I can connect to port 53 with telnet at 192.168.122.1. I've flushed ip-tables to be sure it wasn't firewall rules and that is not the problem. dnsmasq is running, virsh reports default network as stared. I can't find ANY information on troubleshooting libvirt dnsmasq except that it won't play well with other instances of dnsmasq, which is not the problem. I cannot even find where log entries might be for this service. Any ideas on where to look for more information? edit to add: I added another network and that one works fine. I guess I have a workaround but would still like to figure out how to troubleshoot this problem.

  Read the article

• Failure to obtain IP with ARP over Wi-Fi with personal Wi-Fi router in client mode

  - by axk

  I'm trying to connect a Samsung TV to the Internet using a TL-MR3020 personal wireless router in client mode. The TV fails to connect to the network. It sees the ethernet cable connected though. Here's my network topology: Here's what I've captured with Wireshark filtering for ARP (eth.type == 0x0806): It appears the TV fails to get the IP of the gateway (DSL modem/router) for some reason. One thing I've noticed is that the source MAC for the ARP requests coming from the TV is the MAC of the Portable wireless router (that is cd:89:00), not the TV itself and the modem sends the responses to that MAC (I'm not an expert and don't know if its okay or it may make the TV fail to get the requested IP). Also I'm able to ping the TV from the DSL router (through the telnet interface) and the router has an entry in its MAC table for the TV's IP with the Portable wireless router's MAC (that is cd:89:00). If I'm able to ping the TV I suppose it should know the router's MAC to respond to the ping, but then why these continuous ARP requests... I've also tried to connect my desktop trough this Portable wireless router the same way I'm trying to connect the TV and it works fine, I can set the DSL Modem's IP as the default gateway on the desktop's NIC and connect to the Internet. The TV can connect to the Internet when connected to the DSL Router with a wired connection. Any suggestions on what may be the cause of the problem / how to further debug it are welcome. Thanks!

  Read the article

• Server 2003 and XP Client; Why are HTTP connections being silently dropped.

  - by Asa Yeamans

  On my network, my edge-router, a windows 2003 r2 server router with all the latest updates, will drop packets, but only under specific circumstances. I have troubleshot and isolated it down to the most simple configuration i can. There is NO NAT involved. Only fully-public IP addresses. No Firewalls are running either, all ahve been disabled. no packet filters on any interfaces anywhere either. I have a single Windows XP virtual machine and my edge-router(the windows 2003 r2 server, and also a virtual machine) running on a windows 2008 x64 r2 system (running virtual server 2005 as i dont have Intel-VT compatible chip yet). The edge router can access any external http site just fine, no issues. However the windows XP machine is only able to access certain sites. These work: www.google.com www.txstate.edu www.workintexas.com www.thedailywtf.com . These Dont: www.yahoo.com www.utexas.edu en.wikipedia.org slashdot.org www.bing.com. I have removed all possibility of DNS issues by connecting with net-cat from the XP box and sending GET /\r\nHost: \r\n\r\n and that connection replicates the issue as well. The network setup: My statically assigned IP block: x.x.x.168/29 DSL Modem -----PPPoE Connection---- x.x.x.169[EdgeRouter] [EdgeRouter]x.x.x.170 -----Virtual Ethernet----- x.x.x.174 [Test2] Test2's Default gateway is x.x.x.170 and test2 can ping any and every valid, accessible, public IP address with no packet loss what-so-ever. If i connect directly over PPPoE from test2 (the XP box) everything works just fine... Im at my wits end, i have NO IDEA whats causing this.

  Read the article

• Self-connecting printers

  - by Martin Cerny

  Hello, I work as an administrator in a small company using XP Professional on all computers and two servers with Win 2003 Server. Recently a very unusual problam occured one of the computers keeps connecting to all the printers on the network it doesn't matter if it's an administrator or Domain User as soon as somebody logs in the commputer connects all the printers. The printers are either installed on local computers or on the server and shared. There is no log-on script connecting the printers, I install them manualy and none of the other computers shows such behaviour. We have a printer which is installed on two computers and both of them share it (I'm moving it to Server from a small PC which shared it up to now, but some computers still use the old connection), meaning this specific computer connects to one of the printer two times and it can't use either of the connections. How to prevent this self-connecting to all printers (none of the other computers has this problem). If I delte them from the "Printers" folder everything works fine untill I reconnect and the Folder is once again full of all the printers we have. I solved the smaller problem, computer is now capable of printing on all of the printers (it seems there have been some registry issues), after cleaning the registry and reinstalling the printer it seems to work just fine. But the second thing prevails, the computer connects to all the printers in the network (when I remove one/multiple it is reconnected right after the next log-in by any user).

  Read the article

• sporadic routing to another website when opening a common url

  - by user226098

  I have a strange problem in our office: Sometimes when opening a url from one of our projects random url in any browser not the right website shows up but some other website. In most of the cases it redirects to google.com with some parameters like https://www.google.de/?gfe_rd=cr&ei=krOOU8_kGcSKswadyYDQBw&gws_rd=ssl or just the ugly google 404 page). But today it remains on the origial url but shows up the the content of http://debug.netdna-cdn.com/. This happens about 1 time a week and for no apparent reason. Even stranger it only occurs on a single pc in the network. It now happens on two different computers in the network. Both use windows 8. The problem cannot be fixed by clearing the browser cache but by rebooting the pc or using ipconfig /flushdns. So I think it has something to do with the dns cache of the machine. But I have no idea what the reason is for this and how i can figure out how to solve it. Any ideas?

  Read the article

• Which Revision Control Software to use for Personal Dropbox?

  - by wag2639

  I want to set up a sync repositiory that would be similar to Dropbox. Goals/Requirements: Free (Open Source very preferable) Linux host (probably Ubuntu) Windows/Mac/Linux clients Potential for multiple users with limited access (optional) Preferable easy, doesn't necessarily need to be automatic Revision control very preferable Basically, I want to be able to use multiple computers, possible with different OS's, and be able to access, use, and sync files across all of them. I also want to have a local copy of the repository for when I'm not connected to the network (as if I'm working on a laptop, I want to keep a local repository to keep revision and merge later with "master" repository). For example, I'm editing a few pictures on my laptop during the day outside of my network, but when I get home, I would like to sync the changes, including incremental changes, with my desktop at home. I would also like my roommates to be able to access and use this repository too but limit access to certain files. For example, I may want to use this to backup financial records but wouldn't want them to have access to those files. I'm a programmer and familiar with SVN but I know that wouldn't be the most appropriate since it doesn't handle binaries well and doesn't keep a local repository. I know better choices exist but I don't really know them well enough to choose the best one.

  Read the article

• Very slow connection to xserve via afp or smb

  - by Mhoffman13

  Help. File transfer and connection speed to our Xserve are painfully slow from newly purchased iMacs. The Xserve is only used as a file server, its running 10.4.11. The problem seems to be only happening on brand new iMacs running 10.6.3. When connected either over afp or smb copying files is many times slower than usual. Other machines on the network running either 10.4 or 10.5 have a normal connection speed. To try to rule out OS incompatibility I connected the new iMac running 10.6 to another computer running 10.4 over the network. The file transfer speed was fast as normal. So it seems the problems lies with the X serve (maybe). The afp logs either access or error don't show anything unusual. One thing that did look different was when the imac was connected to the Xserve the user had its id listed as its IP address. The other machines connected, had the id of broadcasthost. I also noticed that when connected from the new iMac I can only see one of the mirrors. When any other computer connects both mirrors are shown. Tried a restart of the Xserve but the problem persists. Thanks in advance for any advice

  Read the article

• Regarding AD Domain controllers and remote branch offices

  - by Alex

  We have central HQ building and a lot of small branch offices connecting via VPN and want to implement AD (If you can believe we still haven't). We want everyone to log in using domain accounts and be policed centrally. We are OK with having a RODC in a branch office with like 10 computers. But we have these small branches with two to four PCs only. Some of these branches connect to HQ via IPSec site-to-site VPN, some via remote access (client-based) VPN. So there is no problem with ones that have local RODC or connecting to HQ DCs via VPN router. But how about small branches? We don't really want to set up a machine there, neither we want to invest into Windows Server licenses or fancy network equipment. Also, the problem is that we cannot access HQ DCs via VPN because we are not logged in and connected to HQ internal network yet, so DCs aren't reachable. What is typically done in that situation if it is needed to have central management over policies on those PCs? Or is it better to let 'em loose and use local policies and accounts in this situation?

  Read the article

• Hadoop initscript askes password

  - by Ramesh

  I have installed hadoop on my ubuntu 12.04 single node .I am trying to execute an init script to make the hadoop run on start up but it asks password every time i execute. #!/bin/sh ### BEGIN INIT INFO # Provides: hadoop services # Required-Start: $network # Required-Stop: $network # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Description: Hadoop services # Short-Description: Enable Hadoop services including hdfs ### END INIT INFO PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin HADOOP_BIN=/home/naveen/softwares/hadoop-1.0.3/bin NAME=hadoop DESC=hadoop USER=naveen ROTATE_SUFFIX= test -x $HADOOP_BIN || exit 0 RETVAL=0 set -e cd / start_hadoop () { set +e su $USER -s /bin/sh -c $HADOOP_BIN/start-all.sh > /var/log/hadoop/startup_log case "$?" in 0) echo SUCCESS RETVAL=0 ;; 1) echo TIMEOUT - check /var/log/hadoop/startup_log RETVAL=1 ;; *) echo FAILED - check /var/log/hadoop/startup_log RETVAL=1 ;; esac set -e } stop_hadoop () { set +e if [ $RETVAL = 0 ] ; then su $USER -s /bin/sh -c $HADOOP_BIN/stop-all.sh > /var/log/hadoop/shutdown_log RETVAL=$? if [ $RETVAL != 0 ] ; then echo FAILED - check /var/log/hadoop/shutdown_log fi else echo No nodes running RETVAL=0 fi set -e } restart_hadoop() { stop_hadoop start_hadoop } case "$1" in start) echo -n "Starting $DESC: " start_hadoop echo "$NAME." ;; stop) echo -n "Stopping $DESC: " stop_hadoop echo "$NAME." ;; force-reload|restart) echo -n "Restarting $DESC: " restart_hadoop echo "$NAME." ;; *) echo "Usage: $0 {start|stop|restart|force-reload}" >&2 RETVAL=1 ;; esac exit $RETVAL Please tell me how to run hadoop without entering password.

  Read the article

• Improve wireless performance

  - by djechelon

  Hello, I have a Trust Speedshare Turbo Pro router, which is running on channel 6. I found that the wireless signal (and network performance) dramatically drops from my PDA (I can barely attach to the network, even if I set the PDA's energy settings to maximum wireless performance) when I even exit my room, and I don't have shielded walls or something like that. I can't even stream a SD video from my desktop (connected via LAN) to my laptop using WiFi, while via LAN it works fine. I read that changing router's channel could improve performance due to interference reducing. I found that almost all wireless networks around here run on channels 6 and 11. I tried to go to my router's settings page to change channel, but I found that the combo box only allows me to select 6!! I'm not sure, but I may have been able in the past to change channel, though not to all of the available channels. A few minutes ago I tried a firmware upgrade, but it didn't solve my problem. My question is Is it possible that my router is someway locked to its channel? I bought it on my own, I didn't receive it from my ISP Apart from boosting the antenna power to the maximum (which, by the way, increases the EM radiation my and my family's bodies absorb 24/7 and is little more environment-unfriendly), do you have any tips on getting high quality transmission up to 5 metres from the antenna? Thank you

  Read the article

• Pushing DNSSEC updates with offline keys

  - by eggyal

  In a non-professional capacity, I look after the DNS of some 18 domains: mostly personal/vanity domains for immediate family. I outsource the whole shebang to an inexpensive managed hosting provider with a web interface through which I manage the zones; since the provider also offers DNSSEC, I have successfully deployed that too. These domains are so unimportant that an attack targetted against them seems much less likely than a general compromise of my provider's systems, at which point the records of all their customers might be changed to misdirect traffic (perhaps with extremely long TTLs). DNSSEC could protect against such an attack, but only if the zone's private keys are not held by the hosting provider. So, I wonder: how can one keep DNSSEC private keys offline yet still transfer signed zones to an outsourced DNS host? The most obvious answer (to me, at least) is to run one's own shadow/hidden master (from which the provider can slave) and then copy offline-signed zonefiles to the master as required. The problem is that the only machine I (want to*) control is my personal laptop, which usually connects from a typical home ADSL (behind NAT over a dynamically-assigned IP address). Having them slave from that (e.g. with a very long Expiry time on the zone for periods when my laptop is offline/unavailable) would not only require a Dynamic DNS record from which they can slave (if indeed they can slave from a named host rather than a static IP address), but would also involve me running a DNS server on my laptop and opening both it and my home network up to the incoming zone transfer requests: not ideal. I would prefer a much more push-oriented design, whereby my laptop initiates transfer of offline-signed zonefiles/updates to the provider's servers. I looked into whether nsupdate could fit the bill: documentation is a little sketchy, but my testing (with BIND 9.7) suggests it can indeed update DNSSEC zones, but only where the server holds the keys to perform the zone signing; I have not found a way to have it take an update including the relevant RRSIG/NSEC/etc. records and have the server accept them. Is this a supported use-case? If not, I suspect the only solutions which could fit the bill will involve non-DNS-based transfer of the zone updates and would welcome recommendations that are supported by (hopefully inexpensive) hosting providers: SFTP/SCP? rsync? RDBMS replication? Proprietary API? Finally, what would be the practical implications of such a setup? Key rotation is jumping out at me as being an obvious difficulty, especially if my laptop is offline for extended periods. But the zones are extremely stable, so perhaps I could get away with long-lived ZSKs**...? * Whilst I could run a shadow/hidden master on e.g. an outsourced VPS, I dislike the overhead of having to secure / manage / monitor / maintain yet another system; not to mention the additional financial costs of so doing. ** Okay, this would enable a concerted attacker to replay outdated records—but the risk and impact of such are both tolerable in the case of these domains.

  Read the article

• Problems with XP, Office, and PC in general - any ideas?

  - by molecule

  Hi all This may not make a whole lot of sense so pls bear with me... I am about to perform a routine check on one of my user's PC. Some background - the PC has a Xeon processor and 4Gb of RAM and running XP SP3 He has 2xHDD and pagefile is hosted on the secondary HDD (D:) and min/max values are set to 4096. NO pagefile on C: This user has 6 monitors so he has an NVIDIA Quadro NVS440 hosting 4xmonitors and an NVIDIA Quadro NVS290 hosting 2xmonitors. There is a video card driver from NVIDIA which is compatible with both NVS440 and NVS290 and he is on the latest version of that driver. (Note: Make of video cards are different - one is from leadtek and the other from Nvidia) He is a heavy Bloomberg, Outlook, Word, and Excel user and runs two Citrix applications. Other apps are FoxIt PDF and IE. Problems - Outlook and Excel frequently crashes - I am going to perform an Outlook and Excel repair and also check/remove unnecessary addins - will he lose any customizations if I repaired and chose "Restore my shortcuts while repairing" and do not select "Discard my customized settings and restore default settings". Does repair really repair anything? FYI - It stopped crashing ever since i moved a large spreadsheet he has open to his local HDD instead of over the network. This spreadsheet "refreshes" constantly as it is pulling live data to update cells and I suspect it was auto-saving so frequently that it caused crashes if saving over the network. At times, his right click completely fails to respond. His left click works fine but he can't right click on anything in any Window and even on the desktop. Sometimes, he needs to start to close certain applications such as Adobe and the right click will start functioning again. I removed Adobe and installed FoxIt as I figured it was a resource issue but I do not think so as he does have sufficient resources when the problem is happening. Sometimes he can't bring task manager up until he kills certain apps. Definitely sounds like a resource issue but I am not confident that is the root cause. Also not sure if this is related to one of the apps installed but his Start bar flickers (does not completely disappear) intermittently from time to time. The taskbar icons which are hidden appear and then get hidden again as if it was having "fits". I have performed reg scans, malware scans etc but problems do not go away. I am planning to perform sfc /scannow and office repair but would like to know if anyone has any other suggestions. What about setting a "small" pagefile on C:. I have heard that this is recommended and may be the reason why a minidmp file was not generated when he encountered a blue screen. Also, any feedback on his video cards? Do you think different models would cause problems? The drivers seem to work but he only has 2.5Gb out of 4Gb available RAM as I believe the video card chomped up a portion of this. I have recommended creating a new profile for him but due to the amount of customisations he has and the amount of time and effort it will take to get him up and running again, he prefers to bear with the problem than to go down that path. However, at least once a week, his PC acts up and I can't think of any other tools or techniques to rectify his problems. I guess we are at a stage where we just want to "stabilize" things so he won't encounter issues that frequently. Any feedback is very much appreciated.

  Read the article

• Access server using IP on another interface

  - by Markos

  I am using Windows Server 2012 instead of a router for my home network. Currently I am using RRAS and computers from local network can access Internet correctly. Here is a map of the current setup: [PC1] ---| |---- (lan ip)[Server](wan ip)--> internet [PC2] ---| I have applications running on Server, such as IIS and others. All can be accessed from internet using wan ip and from lan using lan ip. I have a domain, lets say its my-domain.com, which is resolved to my wan ip. What I want is to enable my LAN computers to be able to connect to services on my server using the very same address as internet users: eg http://my-domain.com/. However this does not work for my lan computers. What I understand is that I need to set up some kind of loopback route in a way that packets comming to LAN interface get routed to WAN interface. But I haven't found how to achieve this (in fact, I don't know WHAT to search for). Feel free to ask for additional informations and I will try to update the question.

  Read the article

< Previous Page | 449 450 451 452 453 454 455 456 457 458 459 460  | Next Page >