Search Results

Search found 14745 results on 590 pages for 'setting'.

Page 453/590 | < Previous Page | 449 450 451 452 453 454 455 456 457 458 459 460  | Next Page >

• RAID-capable 3.5" SATA Drives

  - by nroam

  I recently purchased a pair of 1TB Western Digital WD1002FBYS RE3 drives for use in an external RAID enclosure. I have found that they tend to drop out of the array after a while. Thinking it was the enclosure I tried them on another one but found the same issue. So a bit of googling and I found http://www.tomshardware.com/forum/251076-32-raid-issues-western-digital-hard-disk which suggests that: "WD's "RE" (RAID Edition) HDDs support Time-Limited Error Recovery ("TLER" ): http://www.wdc.com/en/products/productcatalog.asp?language=en As a non-TLER HDD fills up with data, the error detection firmware might take too long, and the RAID controller may drop that HDD from a RAID array." So now I wonder what SATA drives have firmware which is compatible with RAID arrays (esp. RAID 1, 5, but not 0)? I have not been able to come up with the magic set of keywords to ellicit the answer from Google. However, various sites suggest that Seagate & Hitachi are in general OK. Does anyone have any generic (or even specific) guidance on how to work out if a drive's firmware may harbour code that is potentially an issue in a RAID0 setting other than stating that it must be 'enterprise' ready?

  Read the article

• Losing internet connection after few minutes (5-10 maybe)

  - by Korchkidu

  I took a computer that was not updated for months. Internet was working just fine so basically, I updated zonealarm, avast and installed all windows updates and especially SP3. After that, when I reboot, Internet works fine but after few minutes, Firefox says that the connection was reset. IE does not work either. However, my connection is still up and running as I can make a ping on www.google.com for example. Here are the solutions I tried with no success so far: 1) Uninstalling SP3; 2) Uninstalling IE8 and IE7; 3) Manually setting DNS and IPs; 4) Removed proxy settings from Firefox and IE; 5) Restarting DNS and DHCP related services; 6) Reset TCP/IP with netsh int ip reset c:\resetlog.txt; 7) Updated my ehternet card driver; 8) Restarted, tweaked all the connections in any directions and any configuration possible I believe; 9) Disabled Zone Alarm and Avast; Also, update kb981793 always fails on install. Please, help me as I spent two days already on this and I cannot find any solution. If I cannot fix this problem tomorrow, I will have to format-reinstall everything. Thanks for any help. Regards.

  Read the article

• How to fix GMail time stamps in Outlook?

  - by SWB

  One of my email accounts is hosted at an ISP with unreliable IMAP support, and I can't change it. Fortunately, I have my personal email set up on Google Apps for Domains, so I created another GMail account there and turned on GMail's features that allow me to send and receive mail through the ISP account using GMail ("Send mail as" and "Get mail from other accounts" in GMail settings on the Accounts tab). I'm now using Outlook to retreive mail from the GMail account through IMAP, which in turn is retreiving mail from the ISP account through POP3. This basically works great, except for one very significant issue: Prior to setting this up, I already had several months of mail in the ISP account that I had been accessing via IMAP. GMail grabbed all of this mail via POP3 at, let's say, noon on April 5. In GMail's web interface (and on my iPod touch, and in Mozilla Thunderbird), all is well: the messages are all shown with their original time stamps. But when Outlook downloads these messages from GMail via IMAP, the time stamps are all set to noon on April 5 (the time GMail downloaded them from the ISP via POP3). That's not good, especially since we're talking about hundreds of messages here over a time span of several months. How can I fix this and get Outlook to display the original time stamps?

  Read the article

• Nginx settings are screwing up my Drupal form submissions, how do I fix?

  - by bflora

  How do I tell Nginx to "ignore" specific URLS or pages on my web site? I run a Drupal site where anonymous visitors get served via NGINX while logged in users get served via Apache. We do this to keep the load down and scale better. It works great, except, since we set up nginx, a good number of Drupal forms no longer work. For example, before installing Nginx, if you created a new article, then clicked "edit" and edited the article. You could click "save" and your changes to the article would be saved. After setting up nginx, when you make edits and then click "save," the page simple refreshes, but now with "nginx-index.php" inserted into the URL. And your changes to the form were not actually saved to the database. So if you go to edit an article, you'll be on domain.com/node/##/edit or something like that. When you try to save your changes to the form, you'll wind up at domain.com/nginx-index.php?q=node/##/edit. And your changes will not be saved. There is a way around this, but only for administrative users. If you go to a form where this problem is happening, then comment or comment-out three lines in our settings.php file, the form will save properly. Those three lines are: // 'cache_form' = array( // 'engine' = 'db', // ), If they're commented, you uncomment them, them save the form. If they're uncommented, you comment them out and save the form. Obviously, this sucks. My friend who set up our server (and then left the country) told me that there are some Nginx settings that can tell it to "ignore" certain URLs or pages which could work here. How do I do this and where do I do it?

  Read the article

• Upgrading only certain packages via the getdeb repo

  - by intuited

  I'm a bit confused about how getdeb.net works now. The last time I got a package from there was a while ago; at that point the procedure was that you would just download a .deb for each package that you wanted to install/upgrade and then install it using dpkg -i. However the inexorable march of progress has lent its trumpets to this system as well, and getdeb installs are now done via their repo, which is registered with apt in /etc/apt/sources.list.d, after you install a single package that makes the changes to the apt database. I've installed that package, and I've discovered that aptitude dist-upgrade now wants to upgrade a lot of packages on my system that weren't ready for upgrades prior to the installation of the getdeb package. If I rename the file /etc/apt/sources.list.d/getdeb.list to something with a different extension, then do aptitude update && aptitude dist-upgrade, it stops wanting to upgrade packages. So I gather that the default behaviour is now to upgrade all packages to the version available at getdeb. This is not particularly appropriate, since these packages are not as well tested as the officially released versions. Is there a config setting somewhere that will prevent upgrading packages to versions from the getdeb repo unless this action is specifically selected? I'd like to be able to pick and choose what packages are upgraded via getdeb.

  Read the article

• Cache Control Headers with IIS 7.5

  - by Brad

  I'm trying to wrap my head around client side (web browser) caching and how it works in relation to IIS 7.5 cache control headers. In particular: If we want to force clients to reload cached resources, how must IIS be configured? Do we need to set expire web content immediately if the resources on the server have a more recent Modified Date (or ETag value)? Right now we're not setting any cache headers. So if I set a cache header of no-cache (which I think is the equivalent of expire web content immediately) will that force the web browser to obtain a new version of a particular file. Or will the browser only request a new version after it deems its current copy to be stale and then from that point forward not cache it? Would a best practice be to set a cache control flag of 1 week, then 8 days before I know I am going to make a change set the cache control down to for instance 30 minutes? But if I do that and then need to immediately expire an item from users caches because there was an issue with it how do I do that?

  Read the article

• SQL Server 2008 Replication: Snap Shot Agent timing out on a specific table

  - by Nai

  Hi all, I am going through the process of setting up a transactional replication on my set up. However, I am unable to generate a full snap shot of my database. I keep getting stuck at the same particular point of the process. From snapshot agent: [46%] The process is running and is waiting for a response from the server Other sources have mentioned increasing the timeout period but I do not think this is the problem as this occurs at around the 10 min mark, way within the default value of 1800s. So, I removed that article/table from the snapshot, and lo and behold, it works. So I was looking at the Schema of the table and in my identity column, the NOT FOR REPLICATION was set to TRUE. All my other tables have it set to FALSE. Could this be the source of the error? Also, I tried changing this to false via the GUI but got received a timeout error. Is there a script that allows me to change this? Thanks all.

  Read the article

• Possible to have different SSLCACertificateFiles under different Location in Apache (client side ssl certs)

  - by Mikko Ohtamaa

  I am setting up Apache to do smartcard authentication. The smartcard login is based on client-side SSL certificates handled by an OS driver. I have currently just one smartcard provider, but in the future there are potentially several of them. I am not sure how Apache 2.2. handles client-side certifications per Location. I did some quick testing and it somehow seemed that only the last SSLCACertificateFile directive would have been effective and this doesn't sound right. Is it possible to have different SSLCACertificateFile per Location in Apache (2.2, 2.4) as described below or is SSL protocol somehow limiting that you cannot have more than one SSLCACertificateFile per IP? Example potential config below how I wish to handle several SSLCACertificateFile on the same server to allow users to log in with different smartcard provides. <VirtualHost 127.0.0.1:443> # Real men use mod_proxy DocumentRoot "/nowhere" ServerName local-apache ServerAdmin [email protected] SSLEngine on SSLOptions +StdEnvVars +ExportCertData # Server-side HTTPS configuration SSLCertificateFile /etc/apache2/certificate-test/server.crt SSLCertificateKeyFile /etc/apache2/certificate-test/server.key # Normal SSL site traffic does not require verify client SSLVerifyClient none SSLVerifyDepth 999 # Provider 1 <Location /@@smartcard-login> SSLVerifyClient require SSLCACertificateFile /etc/apache2/certificate-test/ca.crt # Apache does not natively pass forward headers # created by SSLOptions +StdEnvVars, # so we pass them forward to Python using RequestHeader # from mod_headers RequestHeader set X-Client-DN %{SSL_CLIENT_S_DN}e RequestHeader set X-Client-Verify %{SSL_CLIENT_VERIFY}e </Location> # Provider 2 <Location /@@smartcard-login-provider-2> # For real SSLVerifyClient require SSLCACertificateFile /etc/apache2/certificate-test/provider2.crt # Apache does not natively pass forward headers # created by SSLOptions +StdEnvVars, # so we pass them forward to Python using RequestHeader # from mod_headers RequestHeader set X-Client-DN %{SSL_CLIENT_S_DN}e RequestHeader set X-Client-Verify %{SSL_CLIENT_VERIFY}e </Location> # Connect to Plone ZEO client1 running on fg ProxyPass / http://localhost:8080/VirtualHostBase/https/local-apache:443/folder_sits/sitsngta/VirtualHostRoot/ ProxyPassReverse / http://localhost:8080/VirtualHostBase/https/local-apache:443/folder_sits/sitsngta/VirtualHostRoot/ </VirtualHost>

  Read the article

• Dual DC Time Service

  - by poconnor

  I believe I'm having an issue with my Domain Controllers and Time Server. On my back up DC, I keep seeing a warning stating "The time service has stopped advertising as a time source because the local clock is not synchronized." Does this mean that my backup DC believes it's a Time Server? My PDC should be the time server and I have gone through setting up the PDC as the time server. I was not around for the original setup of the time server with the old PDC and Backup DC. But I believe the old PDC was the time server so I setup the new PDC as the new time server, when I decommissioned the old PDC. Is it possible that the Backup DC was setup as the time server and it still thinks it's suppose to be giving out time to everyone? Registry for PDC has NTP Registry for Backup has NT5D5 Results of w32tm /monitor Getting AD DC list for default domain... Analyzing:delayoffset from DC1.local..com Stratum: 4 delayoffset from DC1.local..com Stratum: 3 Warning: Reverse name resolution is best effort. It may not be correct since RefID field in time packets differs across NTP implementations and may not be using IP addresses. DC2.local..com[192.168.1.8:123]: ICMP: 1ms NTP: -0.6349491s RefID: DC1.local..com [192.168.1.9] DC1.local..com *** PDC ***[192.168.1.9:123]: ICMP: 0ms NTP: +0.0000000s RefID: wwwco1test12.microsoft.com [65.55.21.20]

  Read the article

• W7-pro indexing mydoc on disk partition does not work

  - by Yvan Thery

  I am working on a HP-7100 mini tower running W7 Pro 64bits. My Local HD includes C:/ + 2 disk partitions : all my documents are located on disk partition L:/ and all my media files are on disk partition M:/ The indexing process works well on C:/ and M:/ but does not index the L:/ any more also all of them are allowed to be indexed, also the system is present on all drive security tabs. I have tested to rebuilt the indexing file with a new setting including few directories present on drive C/M/L but still with L: does not work ! One more thing I can tell you is that even after rebuilding the indexing file, I can find some residual directories or files which are out of the test selection. It is like unerased components remaining in the indexing database. As I do not know precisely how the indexing process works it is hard to know what to do ... Recently I had a bad time after using a past restoration procedure ... maybe it did corrupt the indexing file ???? If I start indexing the all L:/ disk partition the system stop at 39 found index also many more are existing .... Does any one from you guys could advise the process to create a new indexing database ... ? Any idea to get out of this mess ? Many thanks for assistance Yvan

  Read the article

• Slow manipulation of netfilter rules

  - by Ole Martin Eide

  I have a script maintaining gre tunnels and firewall rules using the "ip" and "iptables" tools. Setting up hundreds of tunnels, and adresses per interface runs just fine. Takes less than 0.1 second per interface, however when I get around to do the firewall rules everything slows down spending 0.5 per insertion. Why is it running so slow? What can I do to improve the speed? It seems like I could try ipset instead, but I really feel there is something wrong with the kernel or something. The interesting thing is that the first 10 rules runs fast, then it slows down.. mybox(root) foo# iptables -V iptables v1.3.5 mybox(root) foo# uname -a Linux foo 2.6.18-164.el5 #1 SMP Tue Aug 18 15:51:48 EDT 2009 x86_64 x86_64 x86_64 GNU/Linux mybox(root) foo# cat test.sh #!/bin/sh for n in {1..100} do /sbin/iptables -A OUTPUT -s ${n} -j ACCEPT /sbin/iptables -D OUTPUT -s ${n} -j ACCEPT done mybox(root) foo# time ./test.sh real 1m38.839s user 0m0.100s sys 1m38.724s Appriciate any help. Cheers!

  Read the article

• Why can't a PC with 2 network cards be accessed by hostname?

  - by lewis

  I set up PC with 2 network cards, connected to the same LAN. I can connect to this PC (e.g. by remote desktop) only via ip-addresses. Accessing by hostname does not work. Why is this the case? UPDATE: Full environment 1. PC with 2 hardware network adapters. 2. On this PC installed VMWare Workstation. Created 3 VM's, networked by "bridged" network setting in VMWare. 3. In LAN all ip-addresses given from DHCP. 4. Win2k8 on all hosts (both physical and vitrual). As result: 1. PC has 2 ip-address (e.g. 192.168.1.71 and 192.168.1.72). PC available in LAN by ip-addreses, but not avail by hostname. 2. VM's has own ip-addr on each (e.g. 192.168.1.73, *74, *75 etc). They are available from LAN by their ip's, BUT not by their hostnames. How can I access to PC and to VM's by hostname?

  Read the article

• PCI Tv Tuner not receiving signal

  - by C-dizzle

  I inherited an Angel II PCI Dual TV Tuner card, popped it into my computer's PCI slot, plugged in my coax cable, but am having trouble getting any type of signal to it. The computer I am using is Windows 7 Ultimate 32 bit, I know the card works because the computer recognizes it and installs the drivers, or at least I assume it works because of that. I'm trying to use Windows Media Center to watch/record tv. Here are a few things I have tried to get it working: Uninstalled/Reinstalled the newest drivers Tried hooking up an antenna to the coax input instead of my cable Instead of using cable splitter, went directly from wall output into card with coax cable Tried using different output on splitter in case the out port was bad I haven't tried a different coax cable yet, it should be fine since it's pretty new. Since this is my first time setting up a TV Tuner card, is there anything specific that I need to do with it? Is there any configuration that needs to be done on it? Do I need to have a digial receiver? I was getting pretty frustrated with it so I wanted to turn here to the experts, I'm sure someone can help me figure it out.

  Read the article

• How does Google geo location service work?

  - by heaosax

  I dont use google maps much, but I was using it today and I clicked the "Show my location" button for the first time, then firefox asked for permission and I clicked "share my location", google maps showed my location pretty accurate. But, how does this system really works? I mean how can google know where I live? I am connecting to the internet with a VPN, so my "public IP" is not from my country, but from sweden, also I use linux and I change the mac of my wireless device, but google still show my location. I know I can disable this feature setting firefox about:config geo.enabled to false, but I am curious about how google can know where I live even when I dont have a real mac address and my IP is not from my real country. Basically I'd like to know if this feature works only because of code that exists in chrome and firefox (which spies my system)? I am worried about anyone knowing where I live, I mean... where is my privacy? Part of the fun about the internet is remaining anonymous.

  Read the article

• Apache Virtual Hosts behind Cisco Router

  - by Theo

  I'm setting up an Apache 2.2 Ubuntu web server for internal services that is also supposed to be accessed from outside our LAN. Our LAN has a single external IP that is the external IP of our RV042 Cisco router. We have set up several A records on our external DNS server that point to this IP. Our internal DNS server resolve the same records to the internal IP of our web server, so computers from inside the network can access them using the same address as if they were outside. We forwarded the router's external 80 port to our web server's 80 port. I have set up one Virtual Host for each domain name in our list, and my httpd.conf is something like this: ServerName web.domain.com NameVirtualHost *:80 <VirtualHost *:80> ServerName alfresco.domain.com <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass /alfresco http://localhost:8080/alfresco ProxyPassReverse /alfresco http://localhost:8080/alfresco ProxyPass /share http://localhost:8080/share ProxyPassReverse /share http://localhost:8080/share </VirtualHost> <VirtualHost *:80> ServerName crm.domain.com DocumentRoot /var/www/sugarcrm </VirtualHost> Now, this works if we are in our LAN. However, if we are outside of our LAN we reach our web server's default page saying: It Works! This is the default web page for this server. But we can't reach the virtual hosts, as if the domain name is not being preserved when the router forward the packets to the web server. Am I doing something wrong? How can I check what is going on? What should be the settings to make this work from outside?

  Read the article

• How can I stop Excel from eating my delicious CSV files and excreting useless data?

  - by atroon

  I have a database which tracks sales of widgets by serial number. Users enter purchaser data and quantity, and scan each widget into a custom client program. They then finalize the order. This all works flawlessly. Some customers want an Excel-compatible spreadsheet of the widgets they have purchased. We generate this with a PHP script which queries the database and outputs the result as a CSV with the store name and associated data. This works perfectly well too. When opened in a text editor such as Notepad or vi, the file looks like this: "Account Number","Store Name","S1","S2","S3","Widget Type","Date" "4173","SpeedyCorp","268435459705526269","","268435459705526269","848 Model Widget","2011-01-17" As you can see, the serial numbers are present (in this case twice, not all secondary serials are the same) and are long strings of numbers. When this file is opened in Excel, the result becomes: Account Number Store Name S1 S2 S3 Widget Type Date 4173 SpeedyCorp 2.68435E+17 2.68435E+17 848 Model Widget 2011-01-17 As you may have observed, the serial numbers are enclosed by double quotes. Excel does not seem to respect text qualifiers in .csv files. When importing these files into Access, we have zero difficulty. When opening them as text, no trouble at all. But Excel, without fail, converts these files into useless garbage. Trying to instruct end users in the art of opening a CSV file with a non-default application is becoming, shall we say, tiresome. Is there hope? Is there a setting I've been unable to find? This seems to be the case with Excel 2003, 2007, and 2010.

  Read the article

• VPN service into 192 network

  - by tophersmith116

  I'm thinking about setting up a security testing lab. I work on a switched network, and that just makes for unnecessary headaches when doing testing. I'd like to create a 192 network with a few machines inside for DBs and AppServers etc. I will need a pivot machine that connects to both the outer network and the 192 (for automation purposes). But I'd like to be able to connect into the 192 network with my own machine from the outer network as the "attacking" machine (rather than have dedicated attack machines inside the 192 network). Therefore, I'd like to have the pivot server be a VPN server as well, so that my machine can VPN into the 192 network from the outer network. First off, is this even possible? Can I have a single computer with two NICs where a VPN service allows remote connections into the 192? Secondly, I'd like to have multiple outer clients connect to the VPN. Does anyone have any suggestions? I've used Hamachi well before, but I've also seen some good stuff from OpenVPN.

  Read the article

• proftpd initial directory for each user

  - by Dels

  After successfully setting up proftpd server, i want to add initial directory for each users, i have 2 user, webadmin that can access all folder and upload that can only access upload folder ... # Added config DefaultRoot ~ RequireValidShell off AuthUserFile /etc/proftpd/passwd # VALID LOGINS <Limit LOGIN> AllowUser webadmin, upload DenyALL </Limit> <Directory /home/webadmin> <Limit ALL> DenyAll </Limit> <Limit DIRS READ WRITE> AllowUser webadmin </Limit> </Directory> <Directory /home/webadmin/upload> <Limit ALL> DenyAll </Limit> <Limit DIRS READ WRITE> AllowUser upload </Limit> </Directory> All set ok, but i need to tell my ftp client initial directory for each user (otherwise it keep fail to retrieve directory), which i think it should be automatically set for each user (no need to type initial directory in ftp client)

  Read the article

• How can I stop SipVicious ('friendly-scanner') from flooding my SIP server?

  - by a1kmm

  I run an SIP server which listens on UDP port 5060, and needs to accept authenticated requests from the public Internet. The problem is that occasionally it gets picked up by people scanning for SIP servers to exploit, who then sit there all day trying to brute force the server. I use credentials that are long enough that this attack will never feasibly work, but it is annoying because it uses up a lot of bandwidth. I have tried setting up fail2ban to read the Asterisk log and ban IPs that do this with iptables, which stops Asterisk from seeing the incoming SIP REGISTER attempts after 10 failed attempts (which happens in well under a second at the rate of attacks I'm seeing). However, SipVicious derived scripts do not immediately stop sending after getting an ICMP Destination Host Unreachable - they keep hammering the connection with packets. The time until they stop is configurable, but unfortunately it seems that the attackers doing these types of brute force attacks generally set the timeout to be very high (attacks continue at a high rate for hours after fail2ban has stopped them from getting any SIP response back once they have seen initial confirmation of an SIP server). Is there a way to make it stop sending packets at my connection?

  Read the article

• SBS 2008 R2: Did something change with anonymous relays?

  - by gravyface

  Have noticed that prior documentation on setting up anonymous relays in SBS 2008 no longer work without some additional configuration. Used to be able to follow this documentation, which is basically: setup a new receive connector add the IP address(es) that will be permitted to relay check off "anonymous" under Permission Group and then run the Exchange shell script to grant permissions. Now what seems to be happening is that if the permitted IP address happens to fall within the same address space as another more restrictive Receive Connector (like the "Default SBS08" one) and possibly if it's ahead of the new Receive Connector alphabetically (haven't tested that yet), the relay attempt fails with "Client Was Not Authenticated" error. To get it to work, I had to modify the scope of the "Default SBS08" Receive Connector to exclude the one LAN IP that I wanted to allow relaying for. I can't recall ever having to do this for Exchange 2007 Standard and/or any other SBS 2008 servers I've setup over the last couple of years and I don't remember doing this and the wiki entry I added at the office doesn't mention it either. So my question is, has anyone else experienced this? Has there been a new change with R2 or perhaps an Exchange Service Pack?

  Read the article

• How to disable Utility Manager (Windows Key + U)

  - by Skizz

  How do I disable the Windows + U hotkey in Windows XP? Alternatively, how do I stop the utility manager from being active? The two are related. The utilty manager is currently providing a potential security hole and I need to remove it[1]. The system I'm developing uses a custom Gina to log in and start a custom shell. This removes most Windows Key hotkeys but the Win + U still pops up the manager app. Update: Things I've tried and don't work: NoWinKeys registry setting - this only affects explorer hotkeys; Renaming utilman.exe - program reappears next login; Third party software - not really an option, these machines are audited by the clients and additional, third party software would be unlikely to be accepted. Also, the proedure needs to be reasonably straightforward - this has to be done by field service engineers to existing machines (machines currently in Russia, Holland, France, Spain, Ireland and USA). [1] The hole is via the internet options in the help viewer the utility app links to.

  Read the article

• Assigning cores to VM in vSphere

  - by user114933

  Complete vSphere newbie here... Background: So, I have a 12 core machine with 24 VMs on it. Currently, all the processing power is shared between these VMs equally. The question: Can I configure one VM to be given two CPU's worth processing no matter what's happening on the other machines? My Research: I tried two things in vSphere... I set the reservation and limit on one VM to equal the same as two cores. To test if my objective was being reached, I measured the time it would take to gzip a file when other VMs were running nothing and when other VMs were running CPU intensive operations. I expected the time to gzip the file would be the same because this VM gets priority for some processing. Unfortunately, the time taken to gzip the file when other VMs were running something was significantly more than when other VMs were not running anything. I tried setting the Hyperthreaded Core Sharing mode to Internal hoping that this would mean that my VM would get at least an entire core to itself. This did not work either. Thanks in advance!

  Read the article

• Windows 7 mouse multi selection on windows explorer with CTRL and point to select / single click to open

  - by bortao

  This is something that have annoyed me since i changed to Windows 7. I don't do double click for a long time now since windows introduced 1 click selection (Folder Options Click items as follows Single click to open an item). The problem is, when i click Control and hover over the items, they select/deselect automatically every small amount of mouse movement i make. What i want is to select/deselect the items only when i enter/exit them. So to deselect an item im hovering, i have to move the mouse out of it, and then back in. I'm using Intellimouse Explorer official drivers. (edit) Here's another related annoyance: When you are hovering something and move the mouse inside other item (Holding Ctrl) The new item may or may not be selected. If you continue moving the mouse it gets selected/deselected as you move. (more edit) I have found that the parameter HKCU\Control Panel\Mouse\MouseHoverHeight / MouseHoverWidth have some influence here. If it's set to 2, the item select/deselect really quickly as you move the mouse. When set to larger numbers, its slower. But setting to 20 or 200 don't seem to be much different.

  Read the article

• Recommendations for good Unix MTA / groupware solutions? [closed]

  - by Jez

  Possible Duplicate: Exchange server replacement that runs on Linux I'm setting up a Debian server, and one of the things I need on it is an MTA. I don't want to use something like Exim or Postfix because I want something that ties in SMTP, POP3, and IMAP all in one (a la Microsoft Exchange). Most MTAs also seem to be hellishly difficult to configure. Try and read the Exim documentation; you could do a university degree on it (I'm not kidding). When you can get an HTTP server like Cherokee which is easy to configure and has a nice web interface, do MTAs or groupware solutions need to be that hard? I'm aware that some people think "the Unix way" is to have lots of different interacting pieces of software (like maybe an SMTP MTA, POP3 service, webmail service, and overarching manager to tie them all together), but I think this is a situation where that just makes things a lot harder to deal with and one large software suite fits in much more nicely. So, I'm looking for good open source software suites that will run on Debian that: Combine (at least) SMTP, POP3, and IMAP Are easy(ish) to configure Have a nice configuration web interface or GUI Are not defunct projects I don't mind if it's groupware and offers calendaring too, but I would only be using the e-mail functionality for now. Another nice-to-have would be built-in webmail (if we're combining a bunch of functionality, why not?) Note however that I do NOT need Outlook support. I am not really looking for an "Exchange replacement drop-in". The suites I've found so far that seem to match the above criteria (and have appropriate licenses) are Citadel, Kolab, and Zimbra. I'd appreciate anyone who has experience with any of these giving me the pros and cons of them, such as how easy they are to configure and what their performance is like. I'd also appreciate any other suggestions for solutions that fulfil my criteria that I may have missed out.

  Read the article

• One Windows Domain workstation can ping gateway but gets no internet access

  - by dindeman

  One of the (Windows XP SP3) workstations of our Windows Domain could not access internet anymore, this problem suddenly happened overnight. The domain controllers (there are three of them) are all running Windows Server 2008. First I compared the output of ipconfig /all on the faulty workstation with the output of a working workstation and it was just fine as it had always been. In particular the default gateway was correct and always remained pingable from the faulty workstation. I guessed that something was wrong with the DHCP service and I restarted the DHCP server service on all of our three DCs as well as the DHCP client service on the faulty workstation. This didn't solve the issue. I then thought of renewing the DHCP lease with ipconfig /release and ipconfig /renew and here is my first question: why did this never work? The same IP address (192.168.0.45) kept being assigned despite all my attempts to renew it (note that all our workstation are getting their TCP/IP automatically.) Even by leaving the domain and changing the computer name the same address was yet again obtained... Anyway I then proceeded to switch the TCP/IP configuration for that machine manually to another free valid IP address (192.168.0.41)... and then the internet access came back! I then cleared any traces of the previous IP in the DHCP leases list and in the DNS tables of our DCs and, after setting back the TCP/IP configuration to 'automatic', finally, the new lease would be granted (192.168.0.41) alongside with the internet access. My second question: what went suddenly wrong with the original IP address?

  Read the article

< Previous Page | 449 450 451 452 453 454 455 456 457 458 459 460  | Next Page >