Search Results

Search found 23311 results on 933 pages for 'multiple computers'.

Page 454/933 | < Previous Page | 450 451 452 453 454 455 456 457 458 459 460 461  | Next Page >

• File permissions issue with an NFSv4 share, uploaded from a Mac Lion

  - by POP.sicle

  I have an NFSv4 share that was working fine, with Macs using Snow Leopard, to share files across the network. The NFS share has one cloned user/group that all clients autoconnect as. However, when I use a Lion Mac to copy a file from their user directory to the NFS, no other computer (mac SL/mac Lion/Win7) can edit/delete/write to the file that was uploaded - despite having the correct read/write/ex permissions visible on the NFS and through terminal. Attempting to edit the file permissions through Finder completely locks the file. I suspect this has something to do with Lion's ACLs (or maybe its version control) conflicting with NFSv4. Is there a way to disable or ignore extended ACLs or extended file permissions on the NFSv4 side, that would allow users to not run into this conflict? The work around currently is to use NFS Manager and set automounts to ignore ownership but installing NFS manager and configuring automounts for all of the computers seems more troubling than attempting to reconfigure the NFS settings. Advice?

  Read the article

• Listing the routing table takes long time to complete

  - by Rafal Rawicki

  When I print routes defined on my computer using route, it takes about 5 to 20 seconds to complete. Why does it take so much time? With VPN enabled: $ time sudo route Kernel IP routing table (...) real 0m21.423s user 0m0.000s sys 0m0.012s With no VPN, this is about 5 seconds - still, computer can do a lot in this time. I've repeated my measurements few times, getting very similar results each try. My machine is Ubuntu with 3.0.0 kernel, but as far as I know, route on the other computers works the same way.

  Read the article

• Encoding video stream for playback on a vanilla Windows XP with mencoder

  - by Tamás

  I have a bunch of PNG files, generated from a script. They represent consecutive frames of a video sequence and I'd like to encode them into a single AVI file (or some other video format) using mencoder. What parameters should I use to ensure that the video can be viewed on a vanilla Windows XP using Windows Media Player with no extra codecs installed apart from the default ones? So far I've tried -ovc lavc -lavcopts vcodec=wmv2 and -ovc lavc -lavcopts vcodec=msmpeg4 with no success. (Background story: some of the people I'm collaborating with on a scientific project cannot install any codecs on their university computers without the help of the local sysadmins, who are of course not very willing to install anything. I'd like to ensure that they can also view the video files I am creating).

  Read the article

• Mac internet problems

  - by Bradley Herman

  Our office is set up with mostly macs (7 of them) but we do have a windows laptop and a windows desktop on the network as well. The network is configured with a modem going into a switch/router throughout the office to the computers, along with a wireless router. Everything runs fine most of the time, but periodically while using the web, certain sites will stop loading and timeout repeatedly. This usually lasts 20 minutes or so and can be incredibly annoying. Resetting the modem/router and/or rebooting the computer never helps. The weirdest part is that in almost every case, the websites are fine on our Windows machines. I frequently use github, google, Stack Overflow, and jQuery reference and I can count on the sites being unavailable to me at least once a day. While I can't get them to load, I can spin my chair around to the windows server behind me and load the sites just fine. Any idea what the hell could be going on here?

  Read the article

• Umbraco template issues

  - by bomortensen

  Hi fellow Umbraco users, I'm currently building my first umbraco website and since I'm completely new to umbraco I've already ran into a problem which I'm sure is pretty straight-forward to do. That said, I'm by no means a beginner when it comes to building sites that run on a (open source) CMS as I've been using Joomla! since it was called Mambo. Anyway, the site I'm building is here: my site What I want to do is to have some content in the white box that changes when you mouseover/hover one of the menu items. Also that content has to stay "active" when you've clicked on a link (i.e. if you click on "Profile" I need to highlight the Profile menu item with the gray color and the white boxs content needs to be what would be related to the Profile menu item. How do I go about this? What would be the best practice when it comes to showing multiple content on a site? I've watched the video about multiple Content Place Holders, but I never really got it to work. I can't get a page to display in the NavigationPlaceHolder (the placeholder I put in the white box), but thats because the actual page is Frontpage.aspx and not WhateverIsInThenavigationPlaceHolder.aspx. If I go to the mysite.dk/WhateverIsInTheNavigationPlaceHolder.aspx it shows up fine. What have I missed here? :) Thanks in advance! If my question is not clear in some ways, please tell me and I will try to explain it better. All the best, Bo

  Read the article

• Windows - how to clone network connections entry to another machine

  - by tomash

  Let's assume we have two Windows XP computers with identical hardware configuration, including GPRS modem connected to COM1 serial port. On the first PC we add new modem device, set up gprs connection on this port in "Network connections" folder. How avoid clicking the same procedure on second computer? Detailed questions: Where are the entries from "Network connections" stored? File, registry? Is there a possibility to clone such entry between PCs? Question as above but regarding modem entry in device manager - can it be exported from one pc and imported on second?

  Read the article

• Help desk cannot respond to UAC prompts over Remote Assistance

  - by blsub6

  I'm trying to use the in-built Remote Assistance (RA) software in Windows 7 to support my users. I initiate a RA session with the user and ask to remotely control their desktop. They tick a little check box that says something to the effect of 'allow helper to respond to UAC prompts' and it pops up with a UAC prompt. The user cannot respond to the UAC prompt because they're not a local administrator - I am. Isn't that what that little check box is for??? I've found this on TechNet from back in '07 on Vista. From what I've found, I could disable UAC (terrible idea) or make all my users local administrators on their computers (yet another terrible idea). I'm hoping that MS has fixed this little oversight in Windows 7. Remote Assistance is completely useless to me if I can't respond to UAC prompts with my username and password

  Read the article

• Alt-Escape has different effect on different Win-XP machines

  - by Ram Rachum

  This is really weird. On my desktop computer, I often use Alt-Escape to send the active window to the background. This is really useful for window management. However, when I try pressing Alt-Escape on my new laptop, it does something similar but not identical: It sends the active window back, but not all the way to the background. i.e., instead of giving it the lowest index number, it just decrements its index number, probably by 1. Both computers have the same Windows XP Professional. Why is this? And how can I make my laptop computer send the active window to the background instead?

  Read the article

• Ways for managing the installation and configuration of various software applications and settings i

  - by EmpireJones

  What are some ways for managing the installation and configuration of various software applications and settings in group of linux development and server computers? Is a set of basic scripts a good means of attack? I was thinking about just having a ton of scripts, such as: setup_dev_env [install|uninstall|reinstall] setup_nfs [...] setup_nfs_share [...] setup_http [...] setup_memcache_node [...] Is there any better method? It would be nice to be able to "upgrade" an installation script too, for example, to change common development settings.

  Read the article

• How come I can't ping my home computer?

  - by bikefixxer

  I'm trying to set up a vpn into my home computer in order to access files from wherever. I have the home computer set up with a no-ip dynamic dns program so I can always connect, and have also tried using the actual ip address. However, when I try to connect or even ping from anywhere outside of my house I can't get through. I've tried putting that particular computer in the dmz, turned off the computers firewall and anti-virus, and I still don't get anything. I have comcast as my home internet provider. I have also tried from two different locations. Are there any other solutions I can try or is comcast the issue? I used to be able to do this when I ran a small web server at home for fun but now nothing works. Thanks in advance for any suggestions!

  Read the article

• Minimum cost strongly connected digraph

  - by Kazoom

  I have a digraph which is strongly connected (i.e. there is a path from i to j and j to i for each pair of nodes (i, j) in the graph G). I wish to find a strongly connected graph out of this graph such that the sum of all edges is the least. To put it differently, I need to get rid of edges in such a way that after removing them, the graph will still be strongly connected and of least cost for the sum of edges. I think it's an NP hard problem. I'm looking for an optimal solution, not approximation, for a small set of data like 20 nodes. Edit A more general description: Given a grap G(V,E) find a graph G'(V,E') such that if there exists a path from v1 to v2 in G than there also exists a path between v1 and v2 in G' and sum of each ei in E' is the least possible. so its similar to finding a minimum equivalent graph, only here we want to minimize the sum of edge weights rather than sum of edges. Edit: My approach so far: I thought of solving it using TSP with multiple visits, but it is not correct. My goal here is to cover each city but using a minimum cost path. So, it's more like the cover set problem, I guess, but I'm not exactly sure. I'm required to cover each and every city using paths whose total cost is minimum, so visiting already visited paths multiple times does not add to the cost.

  Read the article

• Can't access certain specific IP/domain on Windows 7

  - by jfrobishow

  Been banging my head on the wall for some time now. I have a fresh install of Windows 7 - Ultimate ~x86. Some IPs can't resolve properly, it doesn't matter if I try using Firefox, Chrome or IE I end up with a domain not found (server not found, etc.) I am behind a router, all the other computers aren't affected only this Win 7 machine. It's only certain sites. e.g. xkcd.com, facebook's cdn, google group. Things I have tried: flushdns ipconfig renew Disable IP v6 on the NIC Double checked that the computer was in the right timezone @ the right time. Reinstall the NIC driver. Again 90% of the sites will work but not the major one :P help!!!

  Read the article

• Purpose of LAN Domain?

  - by Leonard Thieu

  What is the purpose of creating a domain name for your LAN? I'm using DD-WRT on my router and assigned local.moofz.com as the LAN domain. I setup Apache HTTP servers on two of the computers on my LAN to test it out. I could reach them on oneil.local.moofz.com and vala.local.moofz.com, but I found out that I could also reach them via their hostnames oneil and vala. If I can reach them through their host names, then what would be the purpose of having a domain name for my LAN?

  Read the article

• Windows Server 2003 AD User Properties Environment doesn't override end user Remote Desktop Client s

  - by caleban

  Windows Server 2003 Domain Controller and Windows XP workstations: Active Directory Users and Computers/Users/User/Properties/Environment/Client devices Connect client drives at logon Connect client printers at logon Shouldn't the above Terminal Services settings in Active Directory override the end user Remote Desktop client settings? In our environment the end user Remote Desktop Client settings take precedence. If printing is disabled on the client but enabled in the user's AD profile then printing is not available. Is this working by design or can I change something to allow the user environment settings in AD to override the end user settings RDC settings?

  Read the article

• Using WDS to make a router act like a makeshift signal booster

  - by cornjuliox

  I've got a router that supports WDS, and I was wondering if I could use it to help extend the range of an existing wireless router? The PC I'm using right now is just barely within the signal range of a wireless router, and the signal is rather weak so I moved my wireless USB adapter away from the computer using a USB extension cord and used a pie tin + some packing tape + a stack of books and a tall wooden stand to make a sort of reflector dish. Sometime in the future I'd like other PCs to be able to connect wirelessly but with the way things are set up I can't move any farther from this spot or I lose the signal entirely. Can I use WDS to bridge the two networks together both to increase the range of the first network and allow computers connected to the 2nd router to share internet access?

  Read the article

• Crossover LAN connection between Ubuntu And Windows 7 is not working

  - by brett

  my question is closely related to: How do I connect Ubuntu 10.04 and Windows 7 with an Ethernet cable? What I am after is: Windows 7-------wireless-----\ Wifi router Ubuntu 10.04----wireless-----/ Windows 7-------wireless-----\ | cross_over_cable Wifi router | Ubuntu 10.04----wireless-----/ What I did was On Windows edit system32\drivers\etc\hosts Add the following line: 192.168.253.2 my_ubuntu_computer_name_&-wired //?not sure if this is right On Ubuntu: sudo gedit /etc/hosts Add the following line: 192.168.253.1 my_pc_computer_name&-wired //?not sure if this is right and then Ubuntu 12.04 as the host Right click on the Network Manager applet, click Edit Connections... In the Wired tab, click Auto eth0, then click Edit... In the IPv4 Settings tab, change Method: to Shared to other computers. Click Apply and enter your password when it asks you. Close everything and reboot. Plug the Ethernet cable into both computers. But, I can connect to my windows network folders from ubuntu via wifi I can't connect to my ubuntu network folders from windows via wifi(in fact this bit was working before - so my wifi connection is worse) my ubuntu Auto Ethernet seems to be on From Ubuntu eth0 Link encap:Ethernet HWaddr 00:11:2f:f3:43:8d inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:2fff:fef3:438d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:172 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:27279 (27.2 KB) Interrupt:19 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1147 errors:0 dropped:0 overruns:0 frame:0 TX packets:1147 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94380 (94.3 KB) TX bytes:94380 (94.3 KB) wlan0 Link encap:Ethernet HWaddr 00:03:c9:e9:6f:bf inet addr:10.1.1.7 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::203:c9ff:fee9:6fbf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13186 errors:0 dropped:0 overruns:0 frame:0 TX packets:12187 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1598882 (1.5 MB) TX bytes:1189555 (1.1 MB) From Windows: Windows IP Configuration Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : BoB Link-local IPv6 Address . . . . . : fe80::ecf7:c445:3725:b9c1%12 IPv4 Address. . . . . . . . . . . : 10.1.1.4 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.1.1.1 Tunnel adapter Local Area Connection* 15: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:1423:3ae3:f5fe:fefb Link-local IPv6 Address . . . . . : fe80::1423:3ae3:f5fe:fefb%23 Default Gateway . . . . . . . . . : :: Tunnel adapter isatap.BoB: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : BoB Tunnel adapter isatap.{D0C8EBA1-335D-4620-8570-6C36E8786D72}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

  Read the article

• Copy files between two windows machines on seperate domains

  - by Simon

  I need to copy several database backups between two computers. The source computer initiates the copy and is a Windows 2000 pc and is a member of domain1. The destination machine is running Windows Server 2000 and is a member of domain2. The machines are on separate networks physically connected via a firewall. The files are currently copied via ssh with http://sshwindows.sourceforge.net/ installed on the destination machine. There is no need to encrypt the contents during the copy, however the passwords should not be sent in the clear. I am looking for a way to copy the files without having to install a server on the destination. I specifically need help with how to set up the permissions and what ports would need to be opened on the firewall.

  Read the article

• How to crop black bars or zoom on Youtube and other Video websites?

  - by cloneman

  Many desktop software (VLC, MPC) and have an option to 'zoom in' , 'crop black bars', or crop to a specific aspect ratio. How can we do this in Fullscreen on Youtube or other flash Video sites? I am the viewer, NOT the video's creator/publisher. iOS Can do this (double tap to zoom, which removes black bars, zoom depth not configurable). afaik, Desktop computers (and android devices), cannot do this on the fly. The only 'workaround' I've found is F11 and zooming of the entire web page - basically a fake full screen and zooming the web page beyond the screen size. Use Case: watching 4:3 flash videos from the web on a widescreen monitor. Looking for all creative solutions, including any software that accesses YouTube without using a web browser.

  Read the article

• Iterating Over Params Hash

  - by Joe Clark

  I'm having an extremely frustrating time getting some images to upload. They are obviously being uploaded as rack/multipart but the way that I'm iterating over my params hash must be causing the problem. I could REALLY use some help, so I can stop pulling out my hair. So I've got a params hash that looks like this: Parameters: {"commit"=>"Submit", "sighting_report"=>[{"number_seen"=>"1", "picture"=>#<File:/var/folders/IX/IXXrbzpCHkq68OuyY-yoI++++TI/-Tmp-/RackMultipart.85991.5>, "species_id"=>"2"}], "authenticity_token"=>"u0eN5MAfvGWtfEzrqBt4qfrL54VJ9SGX0jFLZCJ8iRM=", "sighting"=>{"sighting_date(2i)"=>"6", "name"=>"", "sighting_date(3i)"=>"5", "county"=>"0", "notes"=>"", "location"=>"", "sighting_date(1i)"=>"2010", "email"=>""}} My form can have multiple sighting reports with multiple pictures in each sighting report. Here's my controller code: def create_multiple @report = Report.new @report.name = params[:sighting]["name"] @report.sighting_date = Date.civil(params[:sighting][:"sighting_date(1i)"].to_i, params[:sighting][:"sighting_date(2i)"].to_i, params[:sighting][:"sighting_date(3i)"].to_i) @report.county_id = params[:sighting][:county] @report.location = params[:sighting][:location] @report.notes = params[:sighting][:notes] @report.email = params[:sighting][:email] @report.save! @report.reload for sr in params[:sighting_report] do sighting = SightingReport.new sighting.report_id = @report.id sighting.species_id = sr[:species_id] sighting.number_seen = sr[:number_seen] sighting.save if sr[:picture] sighting.reload for pic in sr[:picture] do p = SpeciesPic.new p.uploaded_picture = pic p.species_id = sighting.species_id p.report_id = @report.id p.save! end end end redirect_to :action => 'new_multiple' end

  Read the article

• Can I find the session ID for a user logged on to another machine?

  - by Dan Tao

  I want to open an application on another computer on the same network via the command line. The scenario here is that the user is in a room surrounded by about 20 computers and wants to be able to launch the same app on every computer without walking from screen to screen opening it up on each individual machine. I've discovered that I can get the basic functionality for this using PsExec as follows: psexec \\[computer] -u [username] -p [password] -d -i [SessionID] [program] For computer, username, password, and program, I'm good. Does anyone know of a way I can figure out which SessionID is assigned to a particular user logged on to a particular machine on the network? Alternately, is there a better way to go about what I'm trying to accomplish?

  Read the article

• ASP.NET Memory Usage in IIS is FAR greater than in DevEnv. Is this normal?

  - by Tom

  Greetings! I have an ASP.NET app that scrapes data from a handful of external pages, parses the relevant bits and displays them in a table. Total data retrieved is 3-4MB and the resulting page is about 1MB. I am using synchronous WebRequest GetResponse for the retrieval, but the same problem existed using an asynchronous BeginGetResponse/EndGetResponse process. There is no database access, no session storage, no caching, but an in-memory list of about 100 objects (total 1MB of data), plus a good amount of AJAX (AjaxControlToolkit). This issue appears on the very first run of the app, even if I have restarted IIS. The issue: When I run the app on my dev computer, the maximum commit charge is about 1.5GB. The biggest user, measured by Task Manager's VM Size, is WebDev.WebServer.exe (600MB). The app runs perfectly. When I run it on my rent-a-server (IIS 7.5, 1GB RAM), the maximum commit charge is over 3.8GB. The biggest user is w3wp.exe at 2.7GB. IIS grinds to a halt and spits out a timed-out error page. Given my limited server budget and the hope of having multiple simultaneous users, I'm kind of in a panic. Is this normal? If I bump the server RAM up to 4GB, will that be enough? Will multiple users require even more memory? Could the culprit be AJAX or the list of objects? Thanks for any insight you can provide.

  Read the article

• Limited connection whenever I connect to a Wi-Fi network outside the company

  - by anderZubi

  Whenever I connect my work laptop to a wireless network outside of my company, the connection shows as Limited, and there is no internet access. I have tried several times by disabling/enabling the network adapter, restarting the computer... without success. Sometimes, after a while, without taking any action, it shows fine, and I have internet access. But can pass 2 hours before this happens. My computer is under a domain network, but I don't think that's the problem, because I can successfuly connect other computers belonging to same domain to other networks. I'm running Windows 8 Pro and my network adapter is the following: Qualcomm Atheros AR9285 Wireless Network Adapter Any idea of which is the problem and how to solve it?

  Read the article

• Prevent registry changes by users

  - by graf_ignotiev

  Background: I run a small computer lab of 10 computers using Windows 7 x64 Enterprise. Our users are set up as limited users. For additional restrictions, I set up local group policy for non-administrators using the microsoft management console. Problem: Recently, I found out that some of these restrictions had been removed. Reviewing the settings MMC and in ntuser.pol showed that the settings should still be in place. However, the related registry settings were missing in ntuser.dat. I already have registry editing disabled in the GPO (though not in silent mode). Question: What is the best way to deal with this situation? Should I look into preventing registry setting changes? Should I set up registry auditing to found out how these keys are getting changed in the first place? Or should I give up the ghost and write some kind of logon script that enforces registry values if they've been change? Any other ideas?

  Read the article

• MySQL Stored Procedures not working with SELECT (basic question)

  - by TMG

  Hello, I am using a platform (perfectforms) that requires me to use stored procedures for most of my queries, and having never used stored procedures, I can't figure out what I'm doing wrong. The following statement executes without error: DELIMITER // DROP PROCEDURE IF EXISTS test_db.test_proc// CREATE PROCEDURE test_db.test_proc() SELECT 'foo'; // DELIMITER ; But when I try to call it using: CALL test_proc(); I get the following error: #1312 - PROCEDURE test_db.test_proc can't return a result set in the given context I am executing these statements from within phpmyadmin 3.2.4, PHP Version 5.2.12 and the mysql server version is 5.0.89-community. When I write a stored procedure that returns a parameter, and then select it, things work fine (e.g.): DELIMITER // DROP PROCEDURE IF EXISTS test_db.get_sum// CREATE PROCEDURE test_db.get_sum(out total int) BEGIN SELECT SUM(field1) INTO total FROM test_db.test_table; END // DELIMITER ; works fine, and when I call it: CALL get_sum(@t); SELECT @t; I get the sum no problem. Ultimately, what I need to do is have a fancy SELECT statement wrapped up in a stored procedure, so I can call it, and return multiple rows of multiple fields. For now I'm just trying to get any select working. Any help is greatly appreciated.

  Read the article

• JSON VIEW using GROUP_CONCAT question

  - by Dan Beam

  Hey DBAs and overall smart dudes. I have a question for you. We use MySQL VIEWs to format our data as JSON when it's returned (as a BLOB), which is convenient (though not particularly nice on performance, but we already know this). But, I can't seem to get a particular query working right now (each row contains NULL when it should contain a created JSON object with the values of multiple JOINs). Here's the general idea: SELECT CONCAT( "{", "\"some_list\":[", GROUP_CONCAT( DISTINCT t1.id ), "],", "\"other_list\":[", GROUP_CONCAT( DISTINCT t2.id ), "],", "}" ) cool_json FROM table_name tn INNER JOIN ( some_table st ) ON st.some_id = tn.id LEFT JOIN ( another_table at, another_one ao, used_multiple_times t1 ) ON st.id = at.some_id AND at.different_id = ao.different_id AND ao.different_id = t1.id LEFT JOIN ( another_table2 at2, another_one2 ao2, used_multiple_times t2 ) ON st.id = at2.some_id AND at2.different_id = ao2.different_id AND ao2.different_id = t2.id GROUP BY tn.id ORDER BY tn.name Anybody know the problem here? Am I missing something I should be grouping by? It was working when I was only doing 1 LEFT JOIN & GROUP_CONCAT, but now with multiple JOINs / GROUP_CONCATs it's messing it up. When I move the GROUP_CONCATs from the "cool_json" field they work as expected, but I'd like my data formatted as JSON so I can decode it server-side or client-side in one step.

  Read the article

< Previous Page | 450 451 452 453 454 455 456 457 458 459 460 461  | Next Page >