Search Results

Search found 14283 results on 572 pages for 'django generic views'.

Page 456/572 | < Previous Page | 452 453 454 455 456 457 458 459 460 461 462 463  | Next Page >

• Dual NVidia graphics cards in Ubuntu / xorg.conf mania

  - by John Zwinck

  I have two NVidia graphics cards: Quadro NVS 295 (PCI Express, dual DisplayPort outputs) GeForce FX 5200 (PCI, DVI and VGA outputs) I have three identical monitors, two on DisplayPort and one on DVI. I'm on Ubuntu Hardy (and cannot currently dist-upgrade for separate reasons). I use the "nvidia" driver. What's new is the GeForce card and the third monitor. I currently have the dual DisplayPort monitors working fine. Here are the display-related parts of my xorg.conf: Section "ServerLayout" Identifier "Default Layout" Screen "PCI-Express Screen" 0 0 # adding this makes X fail to start: Screen "PCI Screen" 0 Inputdevice "Generic Keyboard" Inputdevice "Configured Mouse" EndSection Section "Module" Load "glx" # not sure why/if this is needed EndSection Section "Monitor" Identifier "DELL 2408WFP" Option "DPMS" EndSection Section "Device" Identifier "NVIDIA Quadro NVS 295" Driver "nvidia" Option "RenderAccel" "true" Screen 0 BusID "PCI:2:0:0" EndSection Section "Device" Identifier "NVIDIA GeForce FX 5200" Driver "nvidia" Option "RenderAccel" "true" Screen 1 BusID "PCI:6:4:0" EndSection Section "Screen" Identifier "PCI-Express Screen" Device "NVIDIA Quadro NVS 295" Monitor "DELL 2408WFP" Defaultdepth 24 Option "TwinView" "True" Option "UseEdidFreqs" "True" Option "MetaModes" "1920x1200 +0+1200, 1920x1200 +0+0" EndSection Section "Screen" Identifier "PCI Screen" Device "NVIDIA GeForce FX 5200" Monitor "DELL 2408WFP" Defaultdepth 24 Option "TwinView" "True" Option "UseEdidFreqs" "True" Option "MetaModes" "1920x1200 +0+0" EndSection I use nvidia-settings to configure my monitors, and it does not show the second GPU. lspci, though, shows: 02:00.0 VGA compatible controller: nVidia Corporation Unknown device 06fd 06:04.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] Which is where I got the BusID settings for the two devices (when I just had one device, I didn't have any BusID listed...and adding the BusID hasn't broken anything). What am I missing? How can I make nvidia-settings show my second GPU so I can then configure its monitor?

  Read the article

• Remove Kernel Lock from Unmounted Mass Storage USB Device from the Command Line in Linux

  - by Casey

  I've searched high and low, and can't figure this one out. I have a older Olympus Camera (2001 or so). When I plug in the USB connection, I get the following log output: $ dmesg | grep sd [20047.625076] sd 21:0:0:0: Attached scsi generic sg7 type 0 [20047.627922] sd 21:0:0:0: [sdg] Attached SCSI removable disk Secondly, the drive is not mounted in the FS, but when I run gphoto2 I get the following error: $ gphoto2 --list-config *** Error *** An error occurred in the io-library ('Could not lock the device'): Camera is already in use. *** Error (-60: 'Could not lock the device') *** What command will unmount the drive. For example in Nautilus, I can right click and select "Safely Remove Device". After doing that, the /dev/sg7 and /dev/sdg devices are removed. The output of gphoto2 is then: # gphoto2 --list-config /Camera Configuration/Picture Settings/resolution /Camera Configuration/Picture Settings/shutter /Camera Configuration/Picture Settings/aperture /Camera Configuration/Picture Settings/color /Camera Configuration/Picture Settings/flash /Camera Configuration/Picture Settings/whitebalance /Camera Configuration/Picture Settings/focus-mode /Camera Configuration/Picture Settings/focus-pos /Camera Configuration/Picture Settings/exp /Camera Configuration/Picture Settings/exp-meter /Camera Configuration/Picture Settings/zoom /Camera Configuration/Picture Settings/dzoom /Camera Configuration/Picture Settings/iso /Camera Configuration/Camera Settings/date-time /Camera Configuration/Camera Settings/lcd-mode /Camera Configuration/Camera Settings/lcd-brightness /Camera Configuration/Camera Settings/lcd-auto-shutoff /Camera Configuration/Camera Settings/camera-power-save /Camera Configuration/Camera Settings/host-power-save /Camera Configuration/Camera Settings/timefmt Some things I've tried already are sdparm and sg3_utils, however I am unfamiliar with them, so it's possible I just didn't find the right command. Update 1: # mount | grep sdg # mount | grep sg7 # umount /dev/sg7 umount: /dev/sg7: not mounted # umount /dev/sdg umount: /dev/sdg: not mounted # gphoto2 --list-config *** Error *** An error occurred in the io-library ('Could not lock the device'): Camera is already in use. *** Error (-60: 'Could not lock the device') ***

  Read the article

• Cannot install jdk 1.5 on Ubuntu 12.04

  - by u123

  I have installed Ubuntu 12.04.1 LTS (GNU/Linux 3.2.0-23-generic x86_64). Some info about the machine: $ grep --color "model name" /proc/cpuinfo model name : Intel(R) Xeon(R) CPU E5430 @ 2.66GHz model name : Intel(R) Xeon(R) CPU E5430 @ 2.66GHz model name : Intel(R) Xeon(R) CPU E5430 @ 2.66GHz model name : Intel(R) Xeon(R) CPU E5430 @ 2.66GHz I need to install jdk5 to support an old application. I have tried: ~$ sudo apt-get install openjdk-5-jdk Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package openjdk-5-jdk I have also tried: ~$ sudo apt-get install sun-java5-jdk Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package sun-java5-jdk So its not available in the repos. I have tried to follow this guide (adding the jaunty repos): http://leonardo-pinho.blogspot.dk/2010/11/java-15-no-ubuntu-1010.html but same result. Then I have tried to download jdk-1_5_0_22-linux-i586.bin from here: http://www.oracle.com/technetwork/java/javasebusiness/downloads/java-archive-downloads-javase5-419410.html#jdk-1.5.0_22-oth-JPR and do: ~$ chmod a+x jdk-1_5_0_22-linux-i586.bin ~$ sudo ./jdk-1_5_0_22-linux-i586.bin Sun Microsystems, Inc. Binary Code License Agreement yes Unpacking... Checksumming... 0 0 Extracting... ./jdk-1_5_0_22-linux-i586.bin: 424: ./jdk-1_5_0_22-linux-i586.bin: ./install.sfx.19556: not found ./jdk-1_5_0_22-linux-i586.bin: 1: cd: can't cd to jdk1.5.0_22 Any suggestions?

  Read the article

• SATA drives or chipset throwing DRDY ERR and ICRC ABRT

  - by Matt

  I have an SD-VIA-1A2S PCI card with 2 sata ports (and one ATA-133 that isn't used). Two new Western Digital Caviar Green drives (WD10EARS 1TB) throw repeated errors in kern.log (removed date/time/host info for brevity): [ 7.376475] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1000500 action 0x6 [ 7.376480] ata2.00: BMDMA stat 0x5 [ 7.376483] ata2: SError: { UnrecovData Proto TrStaTrns } [ 7.376489] ata2.00: cmd c8/00:40:20:00:00/00:00:00:00:00/e0 tag 0 dma 32768 in [ 7.376490] res 51/84:2f:20:00:00/00:00:00:00:00/e0 Emask 0x12 (ATA bus error) [ 7.376493] ata2.00: status: { DRDY ERR } [ 7.376495] ata2.00: error: { ICRC ABRT } [ 7.376504] ata2: hard resetting link I'm using Ubuntu 9.04 - 2.6.28-18-generic, though I have tried live cds of Ubuntu 9.10, Fedora 12 and OpenSUSE 11.2 - all running various 2.6.31 kernels - and all received the same error. Based on testing these drives and this card in two other machines and combos of connecting the drives directly to the motherboard or the add-in card, I'm relatively convinced that it's the VIA chipset that is the problem. Another computer that also has an onboard VIA SATA chipset (like the add-in card) produces the same errors when the drives are directly on that motherboard. I have been able to verify that the drives are perfectly good, and I tried everything I can think of in terms of swapping cables, psu isn't overloaded, etc. The error happens on boot once or twice, after using fdisk on the drive once or twice, and constantly when attempting to sync a new mdadm raid 1 array created on the two drives. Any thoughts on where to go from here - driver/kernel wise? I'm completely open to buying a new PCI add-in card if someone can recommend one with 2 internal sata ports that works well in Debian/Ubuntu. Thanks!

  Read the article

• Printer sharing problem (win7 / WinXP): Canon pixma USB printer

  - by Rabarberski

  For a friend, I am trying to share a USB Canon pixma ip3000 printer between two computers in his home network. But I can't get it to work due tot a Canon driver problem. The printer is connected to the Windows 7 (64 bit) computer, and we would like to be able to print from a Windows XP computer. 'Normally' it should be no problem to use Windows printer sharing, however, because one machine is 32-bit and the other is 64-bit, installing an extra driver is required. T he driver provided by canon (here) is described as a 'Canon Inkjet Printer Driver Add-On Module'. The problem is that the .inf file contained in the .exe file isn't accepted as a driver when prompted by the Printer Sharing Wizard, I suspect because it is an add-on driver (whatever that may be). I've connected and installed the printer locally on the XP machine first (which works), so that the XP machine would already know the driver when using it as a network printer, but that doesn't work; the wizard still wants a driver file. Anybody suggestions how to get this working? Maybe there is some sort of generic driver (would be OK even with limited functionality)?

  Read the article

• HTTP Error 503 - Service is unavailable (how fix?)

  - by SilverLight

  i have a web site for download mobile files and there many users in my web site. sometimes i have the error below : HTTP Error 503 - Service is unavailable 1-so why this error happens and what is that mean? 2-as i know appache free up itself when it's oveloaded, but what about iis? how can i put some limitations in my server (i have remote access to my server) for prevent this error happening? a.is limitation of dowload's speed efficient for prevent that error's occur? how can i do that? is squid useful for this job or i can do that with another iis extension. b.is limitation of download's Bandwidth efficient for prevent that error's occur? how can i do that (with iis or another extension)? in right side of iis - configure area - i found some limits. what do those limits mean and can i use them for keep my server alive all the time? EDIT: after viewing event viewer of windows - custom views - server rols - web server (iis) i figure out there is no error in that area. but many warnings and information. the latest warnings and information are like below : warning A worker process '2408' serving application pool 'ASP.NET 4.0 (Integrated)' failed to stop a listener channel for protocol 'http' in the allotted time. The data field contains the error number. warning A process serving application pool 'ASP.NET 4.0 (Integrated)' exceeded time limits during shut down. The process id was '6764'. warning A worker process '3232' serving application pool 'ASP.NET 4.0 (Integrated)' failed to stop a listener channel for protocol 'http' in the allotted time. The data field contains the error number. warning A process serving application pool 'ASP.NET 4.0 (Integrated)' exceeded time limits during shut down. The process id was '3928'. thanks in advance best regards

  Read the article

• Troubleshooting transient Windows I/O "The parameter is incorrect." errors

  - by Kevin

  We have a set of .Net 2.0 applications running on Windows 2003 servers which have started experiencing transient "The parameter is incorrect." Windows I/O errors. These errors always happen accessing a file share on a SAN. The fact that this error has happened with multiple applications and multiple servers leads me to believe that this is an infrastructure issue of some sort. The applications all run under the same domain account. When the errors occur they generally will resolve themselves within a few minutes. I can log in to the application server once the error starts occurring and access the file share myself with no problems. I have looked at the Windows event logs and haven't found anything useful. Due to the generic nature of "The parameter is incorrect.", I am looking for additional troubleshooting suggestions for this error. A sample stack trace is below. Note that while this example was during a directory creation operation, when the problem is occurring, this exception is thrown for any file system operations on the share. Exception 1: System.IO.IOException Message: The parameter is incorrect. Method: Void WinIOError(Int32, System.String) Source: mscorlib Stack Trace: at System.IO.__Error.WinIOError(Int32 errorCode, String maybeFullPath) at System.IO.Directory.InternalCreateDirectory(String fullPath, String path, DirectorySecurity dirSecurity) at System.IO.Directory.CreateDirectory(String path, DirectorySecurity directorySecurity) at System.IO.Directory.CreateDirectory(String path)

  Read the article

• CoreStore Encryption Error on Mac Lion

  - by Michael

  I am trying to encrypt an external drive using diskutil CoreStorage on Mac Lion 10.7.4. I thought the only requirements were that the drive have GUID partition scheme and Journaled HFS+ file system. I think my drive is configured accordingly but when I type the following command I get an error message back: Michaels-MacBook-Pro:~ Michael$ diskutil cs convert disk2 -passphrase TestPassword Error converting disk to CoreStorage: The given file system is not supported on Core Storage (-69756) Here are the details reported for the drive in question: Michaels-MacBook-Pro:~ Michael$ diskutil list disk2 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *500.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Test1 499.8 GB disk2s2 Michaels-MacBook-Pro:~ Michael$ diskutil list disk2 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *500.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Test1 499.8 GB disk2s2 Michaels-MacBook-Pro:~ Michael$ diskutil info disk2s2 Device Identifier: disk2s2 Device Node: /dev/disk2s2 Part of Whole: disk2 Device / Media Name: Test1 Volume Name: Test1 Escaped with Unicode: Test1 Mounted: Yes Mount Point: /Volumes/Test1 Escaped with Unicode: /Volumes/Test1 File System Personality: Journaled HFS+ Type (Bundle): hfs Name (User Visible): Mac OS Extended (Journaled) Journal: Journal size 40960 KB at offset 0xe8e000 Owners: Disabled Partition Type: Apple_HFS OS Can Be Installed: Yes Media Type: Generic Protocol: FireWire SMART Status: Not Supported Volume UUID: 1024D0B8-1C45-3057-B040-AE5C3841DABF Total Size: 499.8 GB (499763888128 Bytes) (exactly 976101344 512-Byte-Blocks) Volume Free Space: 499.3 GB (499315826688 Bytes) (exactly 975226224 512-Byte-Blocks) Device Block Size: 512 Bytes Read-Only Media: No Read-Only Volume: No Ejectable: Yes Whole: No Internal: No I'm a little concerned that the "Partition Type: Apple_HFS" entry is causing the problem, but I don't know how to change that. I only seem to be able to control the "File System Personality: Journaled HFS+" in Disk Utility. Can anyone shed some light on this for me?

  Read the article

• SQL Server Management Studio not scripting all objects

  - by Ian Boyd

  i've been attempting to script a database using SQL Server 2005 Management Studio. i cannot get it to script some objects. It scripts others, but skips some. i can provide detailed screen shots the options being selected including all tables the folder where the script files will go the folder being empty before scripting the scripting process saying Sucess when scripting a table the destination folder no longer empty, with a hundred or so script files the script of some tables not being in the folder. And earlier SSMS would not script some views. Is this a known thing that the the Generate Scripts task does not generate scripts? Update Known issue on Microsoft Connect, but Microsoft couldn't repro the steps, so they closed closed the ticket. Fails on SQL Server 2005, also fails on SQL Server 2008. Update Two Some basic questions: 1.What version of SQL Server? Microsoft SQL Server 2000 - 8.00.194 (Intel X86) Microsoft SQL Server 2005 - 9.00.3042.00 (Intel X86) Microsoft SQL Server 2008 - 10.0.2531.0 (Intel X86) Microsoft SQL Server 2005 Management Studio: 9.00.4035.00 Microsoft SQL Server 2008 Management Studio: 10.0.1600.22 2.What O/S are you running on? Windows Server 2000 Windows Server 2003 Windows Server 2008 3.How are you logging in to SQL server? sa/password Trusted authentication 4.Have you verified your account has full access to all objects? Yes, i have access to all objects. 5.Can you use the objects that fail to script? (eg: select top(10) * from nonScriptingTable) Yes, all objects work fine. SQL Server Enterprise Manager can script the objects fine. Update Three They fail no matter what version of SQL Server you script against. It wasn't a problem in Enterprise Manager: Client Tools SQL Server 2000 SQL Server 2005 SQL Server 2008 ============ =============== =============== =============== 2000 Yes n/a n/a 2005 No No No 2008 No No No Update Four No errors found in the database using: DBCC CHECKDB go DBCC CHECKCONSTRAINTS go DBCC CHECKFILEGROUP go DBCC CHECKIDENT go DBCC CHECKCATALOG go EXECUTE sp_msforeachtable 'DBCC CHECKTABLE (''?'')' Honk if you hate SSMS.

  Read the article

• MSI Installer error 2203; how to force permissions on installer directory?

  - by goober

  [Cross-Posted on StackOverflow.com as well because the question relates to development. Feel free to let me know where it best belongs.] Hi all, I'll try to bullet-point to keep it short: Background / Issue Trying to install ASP.NET MVC 3 RC on my Windows 7 machine. Uninstalled other versions of MVC (2 and 3 Beta 1). Ran the installer -- got a generic error, 2203. Log files said that it was a permissions error on C:\Windows\Installer. Checked C:\Windows\Installer -- sure enough, it's marked as read-only. I un-checked "Read-Only" in the folder properties and applied. It appears to open the dialog and apply to all files. However, when clicking properties again, the read-only box is backed to checked. Checked the security tab of the folder -- both system and the Administrators group have full access. I checked ownership -- the Administrators group is listed as an owner. Verified that I'm in the system as an Administrator (in fact, the only account in the Administrators group besides Administrator). So, what gives? Thanks in advance for any help you can provide!

  Read the article

• Ubuntu NBR karmic boot freezes at fsck from util-linux-ng 2.16

  - by BlueBill

  Hi all, I have a netbook (emachine e250 - equivalent to an acer aspire one) and I have Ubunutu NBR 9.10 installed on it. Every other cold boot freezes at the following error message: "fsck from util-linux-ng 2.16" There is no disk activity, no activity what so ever. I have left the machine sit for over an hour and nothing. It takes a couple of hard resets to be able to boot properly. Once it boots everything works great (wireless, suspend/resume, etc.)! I have spent the last couple of weeks researching the problem and the only thing that seems to work is setting nolapic in the boot string in grub - it boots every time. Unfortunately, nolapic disables the second core and causes problems with suspend resume. At first I thought it was an fsck problem with the first partition on the hard disk as it is a hidden ntfs partition containing the windows xp recover information. So in /etc/fstab I set the partition so that it would be ignored by fsck. This didn't seem to do anything. I have these partitions: /dev/sda1 - an ntfs recovery partition /dev/sda2 - /boot /dev/sda3 - swap /dev/sda5 - / /dev/sda6 - /home I am running kernel version 2.6.31-19-generic and have all the patches (as indicated by update manager). I also have no splash screen so I can see the boot progress. I have only been using NBR since January, I have been using Ubuntu on my desktop since last June (2009-06). What logs should I be looking at? Is there a log for failed boots? Thanks, Troy

  Read the article

• How do I force Windows 7 to recognize my Projector?

  - by user63564

  I have a new Dell XPS with an NVIDIA GeForce GT 445M and an old (several years) Epson PowerLite Cinema 550 projector. Windows 7 refuses to recognize that the projector is connected under normal conditions (I'll get to the strange condition in a moment). Here are some things that I have already tried: Confirm that the projector continues to work well on my old Windows XP laptop. Confirm that the video cable (HDMI to HDMI) is connected Make sure the Dell laptop is plugged in to wall power at all times Reboot both the computer and the projector Click "Detect" under the "Connect to an External Display" Windows dialog (no reaction) Click "Rigorous Display Detection" under NVIDIA Control Panel (dialog: none found) Checked "Force Television Detection on startup" under "My display is not shown..." in NVIDIA Control Panel (no effect) Here's where it gets weird... My projector has three states: off, standby and on. Standby means the power switch on the back is on, but the projector is effectively off (no picture, no access to menu or controls). When I plug in the HDMI cable while the projector is in standby, Windows detects the projector! It lets me switch to Duplicate, Extend, or Project Only mode, and adjusts the resolution appropriately. A new Generic Plug-n-Play monitor shows up in my device manager. A "Seiko EPSON PJ" display shows up in my NVIDIA control panel. Then if I turn my projector on, Windows no longer recognizes the display. This is true whether I turn the projector on while the HDMI cable is plugged in, or if I unplug the HDMI cable while turning on the projector. Anyone have any ideas, because I'm completely stumped...?

  Read the article

• can't find port 22 traffic under VirtualBox

  - by telliott99

  I'm trying to learn to use tcpdump. I thought I'd eavesdrop on my ssh login. The setup is a bit unusual, I have OS X Lion running VirtualBox, with Ubuntu running in the VM. I have ssh enabled and can login from OS X normally: > ssh -p 22 10.0.1.2 -l telliott Welcome to Ubuntu 11.10 (GNU/Linux 3.0.0-17-generic i686) * Documentation: https://help.ubuntu.com/ 0 packages can be updated. 0 updates are security updates. Last login: Sat Mar 31 19:54:36 2012 from toms-mac-mini.local telliott@U32:~$ logout Connection to 10.0.1.2 closed. > I have not obfuscated the ssh port on Ubuntu. From OS X, stroke gives what I expect: > ./stroke 10.0.1.2 22 22 Port Scanning host: 10.0.1.2 Open TCP Port: 22 ssh So from OS X I do: > sudo tcpdump -i en1 -v port 22 Password: tcpdump: listening on en1, link-type EN10MB (Ethernet), capture size 65535 bytes Then I login from OS X to Ubuntu using ssh, but I see nothing with tcpdump. Here is ifconfig from Ubuntu: telliott@U32:~$ ifconfig eth1 Link encap:Ethernet HWaddr 08:00:27:d7:ba:0e inet addr:10.0.1.2 Bcast:10.0.1.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fed7:ba0e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:799 errors:0 dropped:0 overruns:0 frame:0 TX packets:465 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:96863 (96.8 KB) TX bytes:68638 (68.6 KB) Where are the packets I was hoping to see? Thanks for any help.

  Read the article

• How does Subnetting Work?

  - by Kyle Brandt

  How does Subnetting Work, and How do you do it by hand or in your head? Can someone explain both conceptually and with several examples? Server Fault gets lots of subnetting homework questions, so we could use an answer to point them to on Server Fault itself. What is classless routing and why is class-based routing obsolete? If I have a network, how do I figure out how to split it up? If I am given a netmask, how do I know what the network Range is for it? Sometimes there is a slash followed by a number, what is that number? Sometimes there is a subnet mask, but also a wildcard mask, they seem like the same thing but they are different? Someone mentioned something about knowing binary for this? Not looking for links to other sites (unless maybe you have one post with a bunch of good ones). I already know how to subnet, I just thought it would be nice if Server Fault had a generic subnetting answer.

  Read the article

• Using GitOAuthPlugin for Jenkins - not working as expected

  - by Blundell

  I need some clarity and maybe a fix. I'm using this plugin to authorise who views our Jenkins ci server: https://wiki.jenkins-ci.org/display/JENKINS/Github+OAuth+Plugin As I understand it anyone who is auth'd to view one of our github project's can also login to our Jenkins box. This works I thought it would also allow the person logging in to only view the Project that they have GitHub permission on. For instance. Three projects on GitHub (A,B,C). Three builds on Jenkins. User 1 has Git access to all 3 projects (A B C). User 2 has Git access to only 1 project (A). When logging into Jenkins: User 1 can see all 3 projects ( this works ) User 2 can only see project A The problem is User 2 can also see all 3 projects when they should only see 1! Have I got this correct, and if so is this a bug? I have the settings set in Jenkins configuration Github Authorization Settings. Here we have some admin users. One organization. And none out of the 4 checkboxes ticked. (User 2, is not an admin, is not part of the org). The plugin is open sourced here: https://github.com/mocleiri/github-oauth-plugin I was trying to get Jenkins to print me the Logs from the plugin but I also failed at viewing these (to see if there was an issue). I followed these instructions: https://wiki.jenkins-ci.org/display/JENKINS/Logging It's the same concept as outlined below but using GitHub rather than manually selecting users: https://wiki.jenkins-ci.org/display/JENKINS/2012/01/03/Allow+access+to+specific+projects+for+Users%28Assigning+security+for+projects+in+Jenkins%29 Have I got this right or wrong? Is it possible to auth a Jenkins user to only see one project?

  Read the article

• strange Postfix logwatch log summary on my ubuntu vps

  - by DannyRe

  Hi I would be very thankful if someone could help me on explaining this logwatch summary of my postfix installation on my ubuntu 10.04 vps. I dont really know if this might be a normal log file because of the many authentication failed entries and foreign IP addresses. Any advise for a novice? Thx! ****** Summary ************************************************************************************* 113 SASL authentication failed 195 Miscellaneous warnings 8.419K Bytes accepted 8,621 8.419K Bytes delivered 8,621 ======== ================================================== 3 Accepted 60.00% 2 Rejected 40.00% -------- -------------------------------------------------- 5 Total 100.00% ======== ================================================== 2 5xx Reject relay denied 100.00% -------- -------------------------------------------------- 2 Total 5xx Rejects 100.00% ======== ================================================== 116 Connections 1 Connections lost (inbound) 116 Disconnections 3 Removed from queue 3 Delivered 1 Hostname verification errors ****** Detail (10) ********************************************************************************* 113 SASL authentication failed -------------------------------------------------------------- 113 92.24.80.207 host-92-24-80-207.ppp.as43234.net 113 LOGIN 113 generic failure 195 Miscellaneous warnings ------------------------------------------------------------------ 113 SASL authentication failure: cannot connect to saslauthd server: Permission denied 41 inet_protocols: IPv6 support is disabled: Address family not supported by protocol 41 inet_protocols: configuring for IPv4 support only 2 5xx Reject relay denied ----------------------------------------------------------------- 1 46.242.103.110 unknown 1 [email protected] 1 114.42.142.103 114-42-142-103.dynamic.hinet.net 1 [email protected] 1 Connections lost (inbound) -------------------------------------------------------------- 1 After RCPT 3 Delivered ------------------------------------------------------------------------------- 3 myhost.xx 1 Hostname verification errors ------------------------------------------------------------ 1 Name or service not known 1 46.242.103.110 broadband-46-242-103-110.nationalcablenetworks.ru === Delivery Delays Percentiles ============================================================ 0% 25% 50% 75% 90% 95% 98% 100%

  Read the article

• Outlook 2007 / 2010 Calendar: hide meetings in specific category

  - by Jeroen

  Question Is there any easy way in Outlook 2007/2010 to show/hide meetings in a specific category? Preferably only for a specific view (the Month view, in this case). Note: I was almost done writing this question, adding just one more "What I've tried" option, when I found an acceptable (though imperfect) solution. Remembering this SE blog post I figured I might as well post it after all and answer it myself. And who knows, perhaps someone else has a more elegant solution. The reason for me personally is that I'd like to hide the "small, recurring meetings" like our daily stand-up meeting in the month view. I'd prefer an Outlook feature that is meant for this (there must be one for this, right?), but I'm open to workarounds or plugin suggestions as well. What I expected to find somewhere was a list of categories (with added option "No category") where you could select/deselect from which categories you'd see meetings. Something like this mock-up: What I've tried Edit "View Settings", and use a "Filter..." on categories. This has several disadvantages, the major one is that the filter only allows me to choose what I want to show, but not what I want to hide. Even if I tick all categories but one for the filter it would still hide any uncategorized meeting. Similar to 1, but then using Advanced filters. Still a bit clumsy as changing views can be up to three clicks, but this is the best solution so far (see the corresponding answer below). Creating a sub-calendar for these "small" meetings that I wish to hide. This felt a bit clumsy and like overkill, but did provide an easy "select/deselect" option to show/hide these meetings. Search for plug-ins that do this. Couldn't find one (yet).

  Read the article

• pure-ftpd not listening on specified port

  - by Jason McLaren

  I installed the pure-ftpd package (version 1.0.35-1) on an Ubuntu 12.04 box (an EC2 instance based on the standard Ubuntu 12.04 AMI). The pure-ftpd daemon is running (verified with ps), though there is no PID file (expected one to be created by the /etc/init.d/pure-ftpd script). Here's the resulting command that gets run by the init.d script: /usr/sbin/pure-ftpd -l pam -O clf:/var/log/pure-ftpd/transfer.log -o -8 UTF-8 -u 1000 -E -B -g /var/run/pure-ftpd/pure-ftpd.pid Here's my real problem: the ftp server isn't actually listening on any port (checked with netstat and nmap). So I can't ftp to the server (either locally using localhost or remotely using the public IP address). I tried adding a Bind file to /etc/pure-ftpd/conf and restarting, but it didn't help. When I installed pure-ftpd, it replaced inetd with openbsd-inetd, but did not run it since there were no services enabled. So inetd is not listening on port 21 either. (Apparently Ubuntu has a no-inetd-by-default policy, according to https://lists.ubuntu.com/archives/ubuntu-users/2010-September/227905.html .) I want to run pure-ftpd by itself (not with inetd) anyways, since the /etc/init.d/pure-ftpd script requires no inetd if you use the UploadScript feature. I'm not familiar with how Ubuntu handles network services (and can't find any relevant docs besides generic man pages), so I'm probably missing something obvious. Nothing seems out of the ordinary with /etc/hosts.allow (empty) or hosts.deny (empty), and I didn't add any firewall rules (iptables -L shows that the firewall is in its initial state). I've checked the pure-ftpd docs; not sure what else to look at. Any help would be appreciated, thanks!

  Read the article

• Editing a windows XP installation's registry without being able to log in.

  - by Alain

  I've got a windows XP installation that has a corrupt registry. A worm (which was removed) had hijacked the HKLM\Software\Microsoft\Windows NT\CurrentVersion\Winlogon entry (which should have a value of Userinit=C:\windows\system32\userinit.exe When the worm was removed, the corrupt entry was deleted entirely, and now the system automatically logs off immediately after attempting to log in. Regardless of the user and boot mode, no accounts can be logged in to. The only thing required to correct this behavior is to restore the registry key, but I cannot come up with any ways of editing the registry without logging in to an account. I tried remotely connecting to the registry but the required services aren't enabled on the machine. I tried booting on the same machine using the BartPE boot CD but I could not find any way of editing the registry on the C:\Windows installation - running regedit only modifies the X:\I386\ registry in memory. So, what can I use modify the registry of an un-login-able Windows XP instance so that I can log in again? Thanks guys. EDIT: The fix worked. The solution to the auto-logoff problem was, as hoped, to simply add the value mentioned above to the appropriate registry entry. This can be done using the BartPE Boot CD, as described in the accepted answer below, but I used the Offline NT Registry Editor software mentioned in another answer. The steps were: Boot from the NT Registry Editor CD Follow the directions until the appropriate boot sector is loaded. Instead of using one of the default options for modifying passwords or user accounts, type "software" to edit that hive. Type '9' to enter the command line based registry editor. Type "cd Microsoft" (enter) "cd Windows NT" (enter) "cd CurrentVersion" (enter) "cd Winlogon" (enter) Type "nv 1 Userinit" to create a new value under the Winlogon key Type "ev Userinit" to edit the new value, and when prompted, type "C:\windows\system32\userinit.exe" (enter) Type 'q' to quit the registry editor, and as you back out of the system, follow directions to write the hive back to disk. Restart your computer and log in - problem solved. (generic 'warning: back up your registry' disclaimer)

  Read the article

• saslauthd authentication error

  - by James

  My server has developed an expected problem where I am unable to connect from a mail client. I've looked at the server logs and the only thing that looks to identify a problem are events like the following: Nov 23 18:32:43 hig3 dovecot: imap-login: Login: user=, method=PLAIN, rip=xxxxxxxx, lip=xxxxxxx, TLS Nov 23 18:32:55 hig3 postfix/smtpd[11653]: connect from xxxxxxx.co.uk[xxxxxxx] Nov 23 18:32:55 hig3 postfix/smtpd[11653]: warning: SASL authentication failure: cannot connect to saslauthd server: No such file or directory Nov 23 18:32:55 hig3 postfix/smtpd[11653]: warning: xxxxxxx.co.uk[xxxxxxxx]: SASL LOGIN authentication failed: generic failure Nov 23 18:32:56 hig3 postfix/smtpd[11653]: lost connection after AUTH from xxxxxxx.co.uk[xxxxxxx] Nov 23 18:32:56 hig3 postfix/smtpd[11653]: disconnect from xxxxxxx.co.uk[xxxxxxx] The problem is unusual, because just half an hour previously at my office, I was not being prompted for a correct username and password in my mail client. I haven't made any changes to the server, so I can't understand what would have happened to make this error occur. Searches for the error messages yield various results, with 'fixes' that I'm uncertain of (obviously don't want to make it worse or fix something that isn't broken). When I run testsaslauthd -u xxxxx -p xxxxxx I also get the following result: connect() : No such file or directory But when I run testsaslauthd -u xxxxx -p xxxxxx -f /var/spool/postfix/var/run/saslauthd/mux -s smtp I get: 0: OK "Success." I found those commands on another forum and am not entirely sure what they mean, but I'm hoping they might give an indication of where the problem might lie. If it makes any difference, I'm running Ubuntu 10.04.1, Postfix 2.7.0 and Webmin/ Virtualmin.

  Read the article

• Use synergy with Physical KVM

  - by Mr. Man

  I am using synergy on a Linux Mint computer as the server with a Mac as the client. I also have a physical KVM switch. The problem I have is that when ever I switch the physical KVM to my Mac, synergy stops working as in the keyboard and mouse don't work with the Mac. Thanks in advance! EDIT: here are some logs: From the Mint machine: INFO: synergys.cpp,1042: Synergy server 1.3.1 on Linux 2.6.31-14-generic #48-Ubuntu SMP Fri Oct 16 14:04:26 UTC 2009 i686 DEBUG: synergys.cpp,1051: opening configuration synergy.conf DEBUG: synergys.cpp,1062: configuration read successfully DEBUG: CXWindowsScreen.cpp,847: XOpenDisplay(:0.0) DEBUG: CXWindowsScreenSaver.cpp,339: xscreensaver window: 0x00000000 DEBUG: CXWindowsScreen.cpp,117: screen shape: 0,0 1024x768 DEBUG: CXWindowsScreen.cpp,118: window is 0x03800004 DEBUG: CScreen.cpp,38: opened display DEBUG: CXWindowsScreen.cpp,679: registered hotkey F12 (id=efc9 mask=0000) as id=1 NOTE: synergys.cpp,500: started server INFO: CServer.cpp,1141: screen ubuntu shape changed NOTE: CClientListener.cpp,127: accepted client connection DEBUG: CClientProxy1_0.cpp,404: received client marks-mac.local info shape=-1024,0 2304x800 NOTE: CServer.cpp,278: client mac has connected INFO: CServer.cpp,447: switch from ubuntu to mac at -1024,393 INFO: CScreen.cpp,116: leaving screen DEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDEBUG: CXWinavDEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDEBUG302)DEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDE47DEBUG: CXWindowsClipboard.cDEBUG: CXWindowsrset=utf-8 (633), text/plain (462) DEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipboard.cpp,555: added f DEBUG: CXWindCXWDEBUG: CXWindowsClipboard.cpp,555: added fDEBUG:SerDEBUG: CXWindowsClipboard.cpp,555: ed DEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipboard.cpp,555owsClDEBUG: CXWindowsClipboard.cpp,555: 1DEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: getDEBUG: CXWindowsClipboard.cpp,555: added f DEBUG: CXW8_STDEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipboard.cpp,555: added fD textDEBUG: CXWindowsClipboard.cpp,555: added fDEBU DEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipinDEBUG: CXWindowsClipboard.cpp,555:oardDEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindCXWDEBUG: CXWindowsClipboard.cpp,555: added fDEBUG:SerDEBUG: CXWindowsClipboard.cpp,555: ed DEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipboard.cpp,555owsClDEBUG: CXWindowsClipboard.cpp,555: 1DEBUG: CXWindowsClipboard.cpp, s From the Mac: connecting to '192.168.3.5': 192.168.3.5:24800 connected to server entering screen leaving screen entering screen leaving screen stopped client

  Read the article

• Ubuntu Postfix Gmail SMTP Relay Not Working

  - by Nick DeMayo

  I currently have postfix set up to relay messages from my websites through gmail, and up until recently it was working perfectly. However, within the last week or so (not really sure when) I started getting the below error whenever attempting to send an email: Jul 20 07:40:46 localhost postfix/smtp[11958]: connect to smtp.gmail.com[2001:4860:800a::6c]:587: Network is unreachable Jul 20 07:40:46 localhost postfix/smtp[11958]: connect to smtp.gmail.com[173.194.76.109]:587: Connection refused Jul 20 07:40:46 localhost postfix/smtp[11958]: connect to smtp.gmail.com[173.194.76.108]:587: Connection refused Here is my configuration file: # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h #readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = [my domain name] alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases #myorigin = /etc/mailname mydestination = [my host name], localhost.localdomain, localhost relayhost = [smtp.gmail.com]:587 mynetworks = 127.0.0.0/8 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = loopback-only inet_protocols = all ########################################## ##### non debconf entries start here ##### ##### client TLS parameters ##### smtp_tls_loglevel=1 smtp_tls_security_level=encrypt smtp_sasl_auth_enable=yes smtp_sasl_password_maps=hash:/etc/postfix/sasl/passwd smtp_sasl_security_options = noanonymous ##### map username@localhost to [email protected] ##### smtp_generic_maps=hash:/etc/postfix/generic Nothing changed on my server, as far as I know...any ideas what could have caused it to stop working?

  Read the article

• VPN Error 619: Behind Cisco Router WRT310N

  - by ty91011

  I've researched a lot on all the forums and this error is too generic for any of the proposed solutions to work. I'll try to give as much detail and tried solutions. I'm running a CentOS PPTP server behind a Cisco WRT310N Router. Multiple clients from outside with different OS have failed with the same error 619, along with turning off windows firewall and disabling antivirus. I believe this is a router and IP routing issue, and not a client issue. When I connect from a client on the same router as the VPN server, it works when I use the 192. network address- but doesn't work with the public IP address. I've tried telnet to port 1723 from an outside server and I get in. I've opened up the VPN port (1723) on the router, VPN udp port (500), and the GRE port (47) to route to the VPN server's ip. Also, the server's router is behind a DSL modem. I had a glimmer of hope when this site: http://www.chicagotech.net/casestudy/vpnerror619.htm suggested that the PPoE authentication should reside on the router and not the modem. But I still came up empty. So does anybody know what the problem is?

  Read the article

• How do I keep a table up to date across 4 db's to be used in SQL Replication Filtering?

  - by Refracted Paladin

  I have a Win Form, Data Entry, application that uses 4 seperate Data Bases. This is an occasionally connected app that uses Merge Replication (SQL 2005) to stay in Sync. This is working just fine. The next hurdle I am trying to tackle is adding Filters to my Publications. Right now we are replicating 70mbs, compressed, to each of our 150 subscribers when, truthfully, they only need a tiny fraction of that. Using Filters I am able to accomplish this(see code below) but I had to make a mapping table in order to do so. This mapping table consists of 3 columns. A PrimaryID(Guid), WorkerName(varchar), and ClientID(int). The problem is I need this table present in all FOUR Databases in order to use it for the filter since, to my knowledge, views or cross-db query's are not allowed in a Filter Statement. What are my options? Seems like I would set it up to be maintained in 1 Database and then use Triggers to keep it updated in the other 3 Databases. In order to be a part of the Filter I have to include that table in the Replication Set so how do I flag it appropriately. Is there a better way, altogether? SELECT <published_columns> FROM [dbo].[tblPlan] WHERE [ClientID] IN (select ClientID from [dbo].[tblWorkerOwnership] where WorkerID = SUSER_SNAME()) Which allows you to chain together Filters, this next one is below the first one so it only pulls from the first's Filtered Set. SELECT <published_columns> FROM [dbo].[tblPlan] INNER JOIN [dbo].[tblHealthAssessmentReview] ON [tblPlan].[PlanID] = [tblHealthAssessmentReview].[PlanID] P.S. - I know how illogical the DB structure sounds. I didn't make it. I inherited it and was then told to make it a "disconnected app."

  Read the article

• Resolving "JBoss Web Console is Accessible to Unauthenticated Remote Users" vulnerability

  - by IAmJeff

  Our security team has determined there is a vulnerability in one of our systems. We are using version JBoss 5.1.0GA on RHEL 5.10. Vulnerability description: JBoss Web Console is Accessible to Unauthenticated Remote Users Yes, this looks familiar. Refer to Question 501417. I do not find the answer there complete. Can someone (or multiple someones) answer Does a newer version of JBoss fix this vulnerability? Are there links describing, in more detail, manual modification of JBoss configuration files to resolve the issue? Are there others options to remediate this vulnerability? Why don't I find the other answer complete? I'm not at all familiar with JBoss, so this answer seems a bit too simple. The web-console.war contains commented-out templates for basic security in its WEB-INF/web.xml as well as commented-out setup for a security domain in WEB-INF/jboss-web.xml. Just uncomment those basic security blocks and restart? Is there anything else I need to include? This seems generic. Do I need to include anything about my environment, such as absolute paths, etc.? Am I making this too complicated?

  Read the article

< Previous Page | 452 453 454 455 456 457 458 459 460 461 462 463  | Next Page >