Search Results

Search found 12546 results on 502 pages for 'aidan host'.

Page 462/502 | < Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >

• Network Bridging for WiFi-to-Ethernet in linux

  - by shakaran

  It is possible Network Bridging for WiFi-to-Ethernet in linux instead of Ethernet-to-Ethernet? I have a CentOS 6.3 machine. I am using KVM and I want perform a brigde for virtualize more machines. This machine is connected only via wireless connection and it doesn't have a ethernet connection. So, I did a bridge over the WiFi interface like: # cat /etc/sysconfig/network-scripts/ifcfg-br0 DEVICE="br0" NM_CONTROLLED="yes" ONBOOT=yes TYPE=Bridge BOOTPROTO=none IPADDR=192.168.1.50 PREFIX=24 GATEWAY=192.168.1.1 DNS1=8.8.8.8 DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="System br0" Then I edit my wireless conection like: # cat /etc/sysconfig/network-scripts/ifcfg-mywireless ESSID="mywireless" MODE=Managed KEY_MGMT=WPA-PSK WPA_ALLOW_WPA2=yes CIPHER_PAIRWISE=CCMP CIPHER_GROUP=CCMP TYPE=Wireless #BOOTPROTO=none #IPADDR=192.168.1.50 #PREFIX=24 #GATEWAY=192.168.1.1 #DNS1=8.8.8.8 #DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="Auto mywireless" UUID=874***** ONBOOT=yes LAST_CONNECT=1355923469 BRIDGE=br0 After, I restart the network: # /etc/init.d/network restart Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface Auto_mywireless: Error: Unknown connection: 874***** [FAILED] Bringing up interface br0: [ OK ] But as you can see, it show a error. My ifconfig output shows now: # ifconfig br0 Link encap:Ethernet HWaddr 6E:20:AD:CE:D8:AB inet addr:192.168.1.50 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6c20:adff:fece:d8ab/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:6393 (6.2 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:432 errors:0 dropped:0 overruns:0 frame:0 TX packets:432 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:62433 (60.9 KiB) TX bytes:62433 (60.9 KiB) ra0 Link encap:Ethernet HWaddr 00:22:F7:2B:87:E5 inet addr:192.168.1.42 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::222:f7ff:fe2b:87e5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:46 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:487894880 (465.2 MiB) TX bytes:148136473 (141.2 MiB) virbr0 Link encap:Ethernet HWaddr 52:54:00:5B:30:9A inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:70 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:5838 (5.7 KiB) But this doesn't give internet connection and I loss access to 192.168.1.50. So, it is possible setup this networking bridge WiFi-to-Ethernet?

  Read the article

• Unable to connect to SVN server on VPS : Subversion Configuration Problem

  - by Pritam Barhate

  Hello everybody, I purchased a VPS account (centos-5-x86_64) from Hostgator mainly for the purpose of setting up an online Subversion Server. This is the first time I am managing a VPS and my linux skills are not so great, but I have basic knowledge of the OS and have been using it on and off as desktop from last few years. So after foxing through a few tutorials online, as the first step I logged in using SSH root account provided by Hostgator and tried to run, yum install mod_dav_svn subversion As it turns out my account has Cpanel/WHM and since it some concept of easy apache straight forward procedure of yum install mod_dav_svn subversion won't work. After that I found out how it can be worked out by compiling the source and stuff. But the whole procedure looked long and scary. [I am just a linux nub]. so I decided I would just skip whole apache integration stuff and just access the server using svn:// protocol, anyways that's how I configure svn on our LAN. So I installed subversion using yum install subversion It installed fine. Then I created a folder /svn_repos/testproject and ran svnadmin create /svn_repos/testproject/ No Problems Using vi I changed svnserve.conf and passwd files for the repository and added a user with my name. Anonymous users don't have any access, authenticated users have write access. Then I started svnserve using svnserve -d then in same terminal window svn list svn://localhost/svn_repos/testproject Asks for authentication for realm, provided root password then for svn username and password. Provided both. The command returns nothing but exists properly. Returns nothing is understood I didn't import anything. But if try to access svn remotely using in another terminal: svn list svn://ip.add.of.server/svn_repos/testproject svn: Can't connect to host 'ip.add.of.server': Operation timed out Is what I get. Parallels Power Panel that I got from Hostgator reports that: The firewall is not active now. To activate the firewall, choose one of the firewall operation modes. So if firewall is not running and I can access svn using localhost, why the operation is timing out when I try to access svn from a remote machine? Experienced network admins please help. Thanks in advance. Also please suggest a good book which gives detailed information on configuring Dedicated servers + WHM and CPanel.

  Read the article

• HOSTS ignored when disconnected [closed]

  - by Synetech

  Problem I’m seeing a strange and extremely frustrating problem. Any system that is not connect to the Internet (Windows 7 shows the no Internet access icon because it cannot constantly ping Microsoft’s servers) cannot even access locally hosted servers. Hypothesis The problem appears to be that the HOSTS file is not being used to resolve DNS entries when there are no active NICs. Tests / Reproduction You can reproduce it as so: Disconnect a system from the Internet (make sure all wired and wireless connections are disconnected). If necessary, add an entry to the HOSTS file (e.g., 127.0.0.1 foobar or 127.0.0.1 foobar.com) Open a command-prompt Type ping foobar or ping foobar.com Observations The screenshots below show a clear and demonstrative example. In the first snap, a laptop is connected to a router wirelessly. The HOSTS file has only three entries and they resolve just fine. In the second snap, the wireless radio is turned off, so the entries in the HOSTS file are ignored. Moreover, notice that pinging localhost still works even without any active NICs (as does 127.0.0.1), but it is using the IPv6 address (must be hard-coded). You can see the same results in Windows XP with no IPv6 installed, so it has nothing to do with IPv6. I tried pining what should have resolved to 127.0.0.1 while the desktop system (with no wireless NICs) was connected via its Ethernet adapter, then again after pulling the cable from the router and waiting a couple of seconds, then again after plugging the cable back in. The same thing happens if instead of pulling out the cable, the NIC is disabled through software (the [Disable] button in the NIC’s Status dialog or via Device Manager). Conclusions It looks as though the HOSTS file is only being read and used if there is an active NIC, otherwise it is being ignored. This makes some sense in that if there are no active network adapters, then presumably there will not be any network activity, and thus no need to resolve host names via the HOSTS file. This assumption is specious however because it precludes locally hosted virtual servers. The HOSTS file should be used regardless of external DNS server connectivity, otherwise you cannot use simple/consistent/testing-production names for locally hosted servers when not connected to the Internet (for example web servers; help servers for Visual Studio, 3dsmax, etc.; and so on). Question Does anyone know how to force Windows to use the HOSTS file even if there are no active NICs? Appendix Figure 1: While the wireless NIC is connected to the router (the cable-modem is in standby, so no external Internet connectivity). Figure 2: With the wireless radio turned off (the Ethernet port is not unconnected in both cases). Figure 3: Same results in XP with no IPv6

  Read the article

• Asterisk Outgoing CDR Logging To Mysql

  - by user3295551

  Trying to utilize the cdr logging (to mysql) using custom fields. The problem I am facing is only when an outbound call is placed, during inbound calls the custom field I am able to log no problem. The reason I am having an issue is because the custom cdr field I need is a unique value for each user on the system. sip.conf ... ... [sales_department](!) type=friend host=dynamic context=SalesAgents disallow=all allow=ulaw allow=alaw qualify=yes qualifyfreq=30 ;; company sales agents: [11](sales_agent) secret=xxxxxx callerid="<...>" [12](sales_agent) secret=xxxxxx callerid="<...>" [13](sales_agent) secret=xxxxxx callerid="<...>" [14](sales_agent) secret=xxxxxx callerid="<...>" extensions.conf [SalesAgents] include => Services ; Outbound calls exten=>_1NXXNXXXXXX,1,Dial(SIP/${EXTEN}@myprovider) ; Inbound calls exten=>100,1,NoOp() same => n,Set(CDR(agent_id)=11) same => n,CELGenUserEvent(Custom Event) same => n,Dial(${11_1},25) same => n,GotoIf($["${DIALSTATUS}" = "BUSY"]?busy:unavail) same => n(unavail),VoiceMail(11@asterisk) same => n,Hangup() same => n(busy),VoiceMail(11@asterisk) same => n,Hangup() exten=>101,1,NoOp() same => n,Set(CDR(agent_id)=12) same => n,CELGenUserEvent(Custom Event) same => n,Dial(${12_1},25) same => n,GotoIf($["${DIALSTATUS}" = "BUSY"]?busy:unavail) same => n(unavail),VoiceMail(12@asterisk) same => n,Hangup() same => n(busy),VoiceMail(12@asterisk) same => n,Hangup() ... ... For the inbound section of the dialplan in the above example I am able to insert the custom cdr field (agent_id). But above it you can see for the Oubound section of the dialplan I have been stumped on how I would be able to tell the dialplan which agent_id is making the outbound call. My Question: how to take the agent_id=[11] & agent_id=[12] and agent_id=[13] and agent_id=[14] etc and use that as a custom field for cdr on outbound calls?

  Read the article

• VPN Connection causes DNS to use wrong DNS server

  - by Bryan

  I have a Windows 7 PC on our company network (which is a member of our Active Directory). Everything works fine until I open a VPN connection to a customer's site. When I do connect, I lose network access to shares on the network, including directories such as 'Application Data' that we have a folder redirection policy for. As you can imagine, this makes working on the PC very difficult, as desktop shortcuts stop working, software stops working properly due to having 'Application Data' pulled from under it. Our network is routed (10.58.5.0/24), with other local subnets existing within the scope of 10.58.0.0/16. The remote network is on 192.168.0.0/24. I've tracked the issue down to being DNS related. As soon as I open the VPN tunnel, all my DNS traffic goes via the remote network, which explains the loss of local resources, but my question is, how can I force local DNS queries to go to our local DNS servers rather than our customers? The output of ipconfig /all when not connected to the VPN is below: Windows IP Configuration Host Name . . . . . . . . . . . . : 7k5xy4j Primary Dns Suffix . . . . . . . : mydomain.local Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mydomain.local Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : F0-4D-A2-DB-3B-CA DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::9457:c5e0:6f10:b298%10(Preferred) IPv4 Address. . . . . . . . . . . : 10.58.5.89(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 31 January 2012 15:55:47 Lease Expires . . . . . . . . . . : 10 February 2012 10:11:30 Default Gateway . . . . . . . . . : 10.58.5.1 DHCP Server . . . . . . . . . . . : 10.58.3.32 DHCPv6 IAID . . . . . . . . . . . : 250629538 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-AC-76-2D-F0-4D-A2-DB-3B-CA DNS Servers . . . . . . . . . . . : 10.58.3.32 10.58.3.33 NetBIOS over Tcpip. . . . . . . . : Enabled This is the output of the same command with the VPN tunnel connected: Windows IP Configuration Host Name . . . . . . . . . . . . : 7k5xy4j Primary Dns Suffix . . . . . . . : mydomain.local Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mydomain.local PPP adapter Customer Domain: Connection-specific DNS Suffix . : customerdomain.com Description . . . . . . . . . . . : CustomerDomain Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.85(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.0.16 192.168.0.17 Primary WINS Server . . . . . . . : 192.168.0.17 NetBIOS over Tcpip. . . . . . . . : Disabled Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : F0-4D-A2-DB-3B-CA DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::9457:c5e0:6f10:b298%10(Preferred) IPv4 Address. . . . . . . . . . . : 10.58.5.89(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 31 January 2012 15:55:47 Lease Expires . . . . . . . . . . : 10 February 2012 10:11:30 Default Gateway . . . . . . . . . : 10.58.5.1 DHCP Server . . . . . . . . . . . : 10.58.3.32 DHCPv6 IAID . . . . . . . . . . . : 250629538 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-AC-76-2D-F0-4D-A2-DB-3B-CA DNS Servers . . . . . . . . . . . : 10.58.3.32 10.58.3.33 NetBIOS over Tcpip. . . . . . . . : Enabled Routing table Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.58.5.1 10.58.5.89 20 10.58.5.0 255.255.255.0 On-link 10.58.5.89 276 10.58.5.89 255.255.255.255 On-link 10.58.5.89 276 10.58.5.255 255.255.255.255 On-link 10.58.5.89 276 91.194.153.42 255.255.255.255 10.58.5.1 10.58.5.89 21 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.0 192.168.0.95 192.168.0.85 21 192.168.0.85 255.255.255.255 On-link 192.168.0.85 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.58.5.89 276 224.0.0.0 240.0.0.0 On-link 192.168.0.85 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.58.5.89 276 255.255.255.255 255.255.255.255 On-link 192.168.0.85 276 The binding order for the interfaces is as follows: I've not configured the VPN tunnel to use the default gateway at the remote end, and network comms to nodes on both networks are fine. (i.e. I can ping any node on our network or the remote network). I've modified the PPTP connection properties to use the DNS servers 10.58.3.32 followed by 192.168.0.16, yet the query still goes to 192.168.0.16. Edit: The local resources that disappear are hosted on domain DFS roots, which might (or might not) be relevant.

  Read the article

• postfix error: open database /var/lib/mailman/data/aliases.db: No such file

  - by Thufir

  In trying to follow the Ubuntu guide for postfix and mailman, I do not understand these directions: This build of mailman runs as list. It must have permission to read /etc/aliases and read and write /var/lib/mailman/data/aliases. Do this with these commands: sudo chown root:list /var/lib/mailman/data/aliases sudo chown root:list /etc/aliases Save and run: sudo newaliases I'm getting this kind of error: root@dur:~# root@dur:~# root@dur:~# telnet localhost 25 Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. 220 dur.bounceme.net ESMTP Postfix (Ubuntu) ehlo dur 250-dur.bounceme.net 250-PIPELINING 250-SIZE 10240000 250-VRFY 250-ETRN 250-STARTTLS 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN quit 221 2.0.0 Bye Connection closed by foreign host. root@dur:~# root@dur:~# tail /var/log/mail.log Aug 28 01:16:43 dur postfix/master[19444]: terminating on signal 15 Aug 28 01:16:43 dur postfix/postfix-script[19558]: starting the Postfix mail system Aug 28 01:16:43 dur postfix/master[19559]: daemon started -- version 2.9.1, configuration /etc/postfix Aug 28 01:16:45 dur postfix/postfix-script[19568]: stopping the Postfix mail system Aug 28 01:16:45 dur postfix/master[19559]: terminating on signal 15 Aug 28 01:16:45 dur postfix/postfix-script[19673]: starting the Postfix mail system Aug 28 01:16:45 dur postfix/master[19674]: daemon started -- version 2.9.1, configuration /etc/postfix Aug 28 01:17:22 dur postfix/smtpd[19709]: error: open database /var/lib/mailman/data/aliases.db: No such file or directory Aug 28 01:17:22 dur postfix/smtpd[19709]: connect from localhost[127.0.0.1] Aug 28 01:18:37 dur postfix/smtpd[19709]: disconnect from localhost[127.0.0.1] root@dur:~# root@dur:~# postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases, hash:/var/lib/mailman/data/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix default_transport = smtp home_mailbox = Maildir/ inet_interfaces = loopback-only mailbox_command = /usr/lib/dovecot/deliver -c /etc/dovecot/conf.d/01-mail-stack-delivery.conf -m "${EXTENSION}" mailbox_size_limit = 0 mailman_destination_recipient_limit = 1 mydestination = dur, dur.bounceme.net, localhost.bounceme.net, localhost myhostname = dur.bounceme.net mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 readme_directory = no recipient_delimiter = + relay_domains = lists.dur.bounceme.net relay_transport = relay relayhost = smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_recipient_restrictions = reject_unknown_sender_domain, reject_unknown_recipient_domain, reject_unauth_pipelining, permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_authenticated_header = yes smtpd_sasl_local_domain = $myhostname smtpd_sasl_path = private/dovecot-auth smtpd_sasl_security_options = noanonymous smtpd_sasl_type = dovecot smtpd_tls_auth_only = yes smtpd_tls_cert_file = /etc/ssl/certs/ssl-mail.pem smtpd_tls_key_file = /etc/ssl/private/ssl-mail.key smtpd_tls_mandatory_ciphers = medium smtpd_tls_mandatory_protocols = SSLv3, TLSv1 smtpd_tls_received_header = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes tls_random_source = dev:/dev/urandom transport_maps = hash:/etc/postfix/transport root@dur:~# root@dur:~# And am wondering what connection might be. I do see that I don't have the requisite files: root@dur:~# root@dur:~# ll /var/lib/mailman/data/aliases ls: cannot access /var/lib/mailman/data/aliases: No such file or directory root@dur:~# At what stage were those aliases created? How can I create them? Is that what's causing the error error: open database /var/lib/mailman/data/aliases.db: No such file or directory Aug 28 01:17:22 dur postfix/smtpd[19709]: connect from localhost[127.0.0.1]?

  Read the article

• Setting up Virtual Hosts with Apache on Windows 2008 server for multiple sites. Complicated setup,

  - by Roeland

  Hey guys! I am setting up apache on my windows 2008 server at my home. It will serve 2 functions. Subversion hosting to allow me and some others to manage company documents with version control Local website hosting for web development. Will need to run several websites since I generally work on more then one site at a time. Heres what I have done so far. I set up subversion and apache 2.2 using some walk troughs. I changed the default port to 1337. (im a nerd) Using dyndns.com I created a domain to forward to my home ip which is dynamic. ( company.gotdns.org) I then went into my DNS for my company.com and added a record to point repo.company.com to company.gotdns.org At this point people who need access to my file repository can access by going to repo.company.com/repo which is good so far. My question comes on the next step, setting up virtual hosts with apache. Ideally I would like to have my local website be viewable by some others in the company from their homes. So, say I am working on site1, I would like to have them be able to view this by going site1.roeland.bythepixel.com. At the same time, I would like to have site10.wouter.bythepixel.com go to his local setup for site10. What I have done for this: I went into my DNS for company.com and added a record to point roeland.company.com to company.gotdns.org (which translates to my ip). I added code to my httpd-vhosts.conf (listed at bottom) I added code to my host file (listed at bottom) Hah, so of course this doenst work as excepted.. going to site1.roeland.bythepixel.com doesnt bring up my test1 site. Could anyone point me where I may be going wrong? Thanks! hosts: 127.0.0.1 localhost 127.0.0.1 sensenich.roeland.bythepixel.com ::1 localhost httpd-vhosts.conf: <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot "F:/Current Projects/sensenich.com" ServerName sensenich.roeland.bythepixel.com ErrorLog "logs/sensenich.roeland.bythepixel.com-error.log" CustomLog "logs/sensenich.roeland.bythepixel.com-access.log" common </VirtualHost>

  Read the article

• LDAP installed, running, but can't connect remotely [Ubuntu 10.10]

  - by Casey Jordan

  Hi all, I installed LDAP on my ubuntu 10.10 system, using the tutorial found here: https://help.ubuntu.com/10.10/serverguide/C/openldap-server.html Everything seems to be working well, when logged into the server via ssh I can run commands like: > ldapsearch -xLLL -b "dc=easydita,dc=com" uid=john sn givenName cn dn: uid=john,ou=people,dc=easydita,dc=com sn: Doe givenName: John cn: John Doe So I think that's a good sign that things are working well. However I have had zero luck connecting to the server remotely via GUI tools or command line. I have tied JXplorer, and LDAP administration tool. Running commands like this: > ldapsearch -xLLL -W -H ldap://ice.rit.edu -d1 "dc=easydita,dc=com" ldap_url_parse_ext(ldap://ice.rit.edu) ldap_create ldap_url_parse_ext(ldap://ice.rit.edu:389/??base) Enter LDAP Password: ldap_sasl_bind ldap_send_initial_request ldap_new_connection 1 1 0 ldap_int_open_connection ldap_connect_to_host: TCP ice.rit.edu:389 ldap_new_socket: 3 ldap_prepare_socket: 3 ldap_connect_to_host: Trying 127.0.0.1:389 ldap_pvt_connect: fd: 3 tm: -1 async: 0 ldap_open_defconn: successful ldap_send_server_request ber_scanf fmt ({it) ber: ber_scanf fmt ({i) ber: ber_flush2: 34 bytes to sd 3 ldap_result ld 0xb8940170 msgid 1 wait4msg ld 0xb8940170 msgid 1 (infinite timeout) wait4msg continue ld 0xb8940170 msgid 1 all 1 ** ld 0xb8940170 Connections: * host: ice.rit.edu port: 389 (default) refcnt: 2 status: Connected last used: Thu Mar 17 19:42:29 2011 ** ld 0xb8940170 Outstanding Requests: * msgid 1, origid 1, status InProgress outstanding referrals 0, parent count 0 ld 0xb8940170 request count 1 (abandoned 0) ** ld 0xb8940170 Response Queue: Empty ld 0xb8940170 response count 0 ldap_chkResponseList ld 0xb8940170 msgid 1 all 1 ldap_chkResponseList returns ld 0xb8940170 NULL ldap_int_select read1msg: ld 0xb8940170 msgid 1 all 1 ber_get_next ber_get_next: tag 0x30 len 16 contents: read1msg: ld 0xb8940170 msgid 1 message type bind ber_scanf fmt ({eAA) ber: read1msg: ld 0xb8940170 0 new referrals read1msg: mark request completed, ld 0xb8940170 msgid 1 request done: ld 0xb8940170 msgid 1 res_errno: 49, res_error: <>, res_matched: <> ldap_free_request (origid 1, msgid 1) ldap_parse_result ber_scanf fmt ({iAA) ber: ber_scanf fmt (}) ber: ldap_msgfree ldap_err2string ldap_bind: Invalid credentials (49) I am pretty sure that I set up the admin password correctly, but the tutorial was not very specific about that. (Also could not find instructions on how to reset admin password.) Additional info: I was told that this file might hold important information so I will post it: /etc/ldap/slapd.d/cn=config/olcDatabase={0}config.ldif dn: olcDatabase={0}config objectClass: olcDatabaseConfig olcDatabase: {0}config olcAccess: {0}to * by dn.exact=cn=localroot,cn=config manage by * break olcRootDN: cn=admin,cn=config structuralObjectClass: olcDatabaseConfig entryUUID: eca09490-e524-102f-87c5-17d7a82e8985 creatorsName: cn=config createTimestamp: 20110317205733Z entryCSN: 20110317205733.193089Z#000000#000#000000 modifiersName: cn=config modifyTimestamp: 20110317205733Z Given that it seems I have this almost set up correctly is there any steps I can take to correct this? Thanks, Casey

  Read the article

• Configuring Windows 2003 As A Router

  - by Sean M

  I am trying to configure a Windows 2003 server to act as a router, so that the two subnetworks that I'm dealing with can communicate with one another without NAT. I am mostly sure that I have configured Windows 2003 incorrectly, and I'm finding it very difficult to drill down through Google results to something helpful. I have a 192.168.1.0/24 network that is my "production" network (in the sense that I'm in trouble if I screw it up) and a 10.0.0.0/8 network that is my test network. The 192.168.1.0 network is ruled by a gateway whose routing table looks like this (my address redacted): The Windows 2003 server, "prime," is multihomed. Its network adapters are at 192.168.1.122, (as seen above), 10.0.0.1, and 10.0.0.2. I added the Routing and Remote Access role to it, and enabled LAN routing. I do not have it using RIP or other routing protocols. Its current routing table is shown below. To me, it looks like all of the right routes are there for traffic to pass between the 192.168.1.0 network and the 10.0.0.0 network. However, traffic does not pass. The 10.0.0.11 and .12 clients cannot be contacted from the 192.168.1.0 network. When I use traceroute to try to get to them, the trace gets to the Windows 2003 server's 192.168.1.122 address, then produces nothing but "* * *" timeouts. When I try to traceroute to 192.168.1.1 from a 10.0.0.0-network client, I get "destination host unreachable." However, I know that the routing is working at least a little, because from the 192.168.1.0 network, I can connect to the Windows server just fine by referring to it as 10.0.0.1. What static routes would allow me to contact 10.0.0.11 and .12 from the 192.168.1.0 network? Is it possible to tell the Windows server "since you are a DHCP/DNS server, you already know routes to get to machines that are getting IP addresses from you, please add those to your routing table" ? Will using RIP or OSPF on the Windows server actually be helpful in this situation?

  Read the article

• Apache + PHP in paths with accented letters

  - by Álvaro G. Vicario

  I'm not able to run a PHP enabled web site under Apache on Windows XP if the path to DOCUMENT_ROOT contains accented letters. I'm not referring to the script file names themselves but to any folder in the path components. I have this virtual host definition: <VirtualHost *:80> ServerName foo.local DocumentRoot "E:/gonzález/sites/foo" ErrorLog logs/foo.local-error.log CustomLog logs/foo.local-access.log combined <Directory "E:/gonzález/sites/foo"> AllowOverride All Options Indexes FollowSymLinks Order allow,deny Allow from all </Directory> </VirtualHost> If I save the file in ANSI I get a syntax error: DocumentRoot must be a directory If I save the file in Unicode I get another syntax error: Invalid command '\xff\xfe#', perhaps misspelled or defined by a module not included in the server configuration (looks like it's complaining about the BOM) If I save the file in BOM-less UTF-8 Apache works fine and it serves static files with no apparent issue... ... however, PHP complaints when loading any *.php file (even an empty one): Warning: Unknown: failed to open stream: No such file or directory in Unknown on line 0 Fatal error: Unknown: Failed opening required 'E:/gonzález/sites/foo/vacio.php' (include_path='.;C:\Archivos de programa\PHP\pear') in Unknown on line 0 I decided to try the 8+3 short name of the directory (just a test, I don't want to use such a workaround): <VirtualHost *:80> ServerName foo.local DocumentRoot "E:/GONZLE~1/sites/foo" ErrorLog logs/foo.local-error.log CustomLog logs/foo.local-access.log combined <Directory "E:/GONZLE~1/sites/foo"> AllowOverride All Options Indexes FollowSymLinks Order allow,deny Allow from all </Directory> </VirtualHost> But I get the same behaviour: Warning: Unknown: failed to open stream: No such file or directory in Unknown on line 0 Fatal error: Unknown: Failed opening required 'E:/gonzález/sites/foo/vacio.php' (include_path='.;C:\Archivos de programa\PHP\pear') in Unknown on line 0 While there're obvious workarounds (use plain ASCII in all directory names or create NTFS junctions to hide actual names) I can't believe that this cannot be done. Do you have more information about the subject? My specs include 32 bit Windows XP Professional SP3, Apache/2.2.13 and PHP/5.2.11 running as Apache module (but I've noticed the same issue in another box with Windows Vista and PHP/5.3.1).

  Read the article

• Linux not picking up new partition correctly on emc pseudo device

  - by James

  Hi We have a database server running oracle rac. We were recently running out of space on the main LUN that it is attached to. I created a new 100GB LUN and concatenated this onto the existing LUN creating a new MetaLUN. After some messing I managed to get linux to recognise the new space. I then created a new partition in on the pseudo device, to use the new space. Previously when I have done this on other system the next step is to create an ASM disk on the new partition and add this disk to the oracle disk group. This however fails. I am aware of various issues with ASM and powerpath, but I don't think this is the issue here. As on while investigating the issue I discovered that one of the underlying logical device is not reflecting the size change. See below; Powermt displays all of the underlying logical units [root@XXXXX~]# powermt display dev=emcpowerd Pseudo name=emcpowerd CLARiiON ID=CKM00091500009 [VFRAC2] Logical device ID=6006016030312200787502866C65DE11 [LUN 30] state=alive; policy=CLAROpt; priority=0; queued-IOs=0 Owner: default=SP A, current=SP A Array failover mode: 1 ============================================================================== ---------------- Host --------------- - Stor - -- I/O Path - -- Stats --- ### HW Path I/O Paths Interf. Mode State Q-IOs Errors ============================================================================== 3 qla2xxx sde SP A0 active alive 0 0 3 qla2xxx sdj SP B0 active alive 0 0 4 qla2xxx sdo SP A1 active alive 0 0 4 qla2xxx sdt SP B1 active alive 0 0 Fdisk on the pseudo device shows correct space. [root@XXXXX ~]# fdisk -l /dev/emcpowerd Disk /dev/emcpowerd: 429.4 GB, 429496729600 bytes 255 heads, 63 sectors/track, 52216 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/emcpowerd1 1 39162 314568733+ 83 Linux /dev/emcpowerd2 39163 52216 104856255 83 Linux fdisk on one of the logical units is wrong [root@XXXXX~]# fdisk -l /dev/sde Disk /dev/sde: 322.1 GB, 322122547200 bytes 255 heads, 63 sectors/track, 39162 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sde1 1 39162 314568733+ 83 Linux /dev/sde2 39163 52216 104856255 83 Linux fdisk on the rest of the units is fine [root@XXXXX ~]# fdisk -l /dev/sdj Disk /dev/sdj: 429.4 GB, 429496729600 bytes 255 heads, 63 sectors/track, 52216 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdj1 1 39162 314568733+ 83 Linux /dev/sdj2 39163 52216 104856255 83 Linux Also when I created the the partition linux did not create the any entries in the /dev directory for the second partition so I created these manually [root@XXXXX dev]# mknod sde2 b 8 66 [root@XXXXX dev]# ls -al sd[ejot]? brw-r----- 1 root disk 8, 65 Dec 29 14:20 sde1 brw-r--r-- 1 root disk 8, 66 Apr 8 20:31 sde2 brw-r----- 1 root disk 8, 145 Dec 29 14:19 sdj1 brw-r--r-- 1 root disk 8, 146 Apr 8 20:33 sdj2 brw-r----- 1 root disk 8, 225 Apr 6 23:12 sdo1 brw-r--r-- 1 root disk 8, 226 Apr 8 20:33 sdo2 brw-r----- 1 root disk 65, 49 Dec 29 14:19 sdt1 brw-r--r-- 1 root disk 65, 50 Apr 8 20:33 sdt2 This is a production server that we cannot easily reboot. Any ideas would be much appreciated. J

  Read the article

• Connecting to localhost resolves 127.0.0.1 but connects with external IP [Linux, Debian]

  - by skgsergio

  I'm having a problem with a dedicated server, I don't known if it's the default behavior but this is the problem: If I connect to a service located on the server with localhost the service gets as source IP the external IP. Let me show an example, I use netcat for listening on 127.0.0.1:4444 xxxxxx # nc -vv -l -s 127.0.0.1 -p 4444 listening on [127.0.0.1] 4444 ... Lets check if it's ok: xxxxxx ~ # netstat -atnp | grep 4444 tcp 0 0 127.0.0.1:4444 0.0.0.0:* LISTEN 14038/nc Ok lets connect: xxxxxx ~ # nc -vv 127.0.0.1 4444 localhost [127.0.0.1] 4444 (?) open Return to the tty that have the listening process and I get this: connect to [127.0.0.1] from xxxxxx.net [176.31.xxx.xx] 50354 So that's the problem. I have a server daemon that have to listen on localhost and checks that the ip is 127.0.0.1 when the client connects but for some reason when I connect to localhost it reports the external ip... If I do the same with IPv6 it works as excepted... Detects connection as localhost (::1). Some info that can be useful: "localhost" resolves without problems to 127.0.0.1 xxxxxx ~ # ping -c1 localhost PING localhost (127.0.0.1) 56(84) bytes of data. 64 bytes from localhost (127.0.0.1): icmp_req=1 ttl=64 time=0.086 ms Nothing weird on my hosts file, I think... xxxxxx ~ # grep -v ^# /etc/hosts 127.0.0.1 localhost localhost.localdomain 176.31.xxx.xx xxxxxx.net ns1.xxxxxx.net ::1 ip6-localhost ip6-loopback feo0::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters ff02::3 ip6-allhosts And ifconfig reports all ok... eth0 Link encap:Ethernet HWaddr e0:69:95:d8:30:a1 inet addr:176.31.xxx.xx Bcast:176.31.108.255 Mask:255.255.255.0 inet6 addr: 2001:41d0:8:xxxx::/64 Scope:Global inet6 addr: 2001:41d0:8:xxxx:x:xx:xx:xx/64 Scope:Global inet6 addr: fe80::e269:95ff:fed8:30a1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16916 errors:0 dropped:0 overruns:0 frame:0 TX packets:16914 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8410679 (8.0 MiB) TX bytes:10539881 (10.0 MiB) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:5570 errors:0 dropped:0 overruns:0 frame:0 TX packets:5570 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:744490 (727.0 KiB) TX bytes:744490 (727.0 KiB)

  Read the article

• Ubuntu unattended-upgrades stops apache

  - by Robbie

  This morning i was alerted to the fact that both apache instances serving my app were not responding to requests from my load balancer. I attempted apachectl restart and it said apache was not running. So, i started apache on both instances and got the service up again. I then followed the logs and worked out that both had performed upgrades via the unattended-upgrades package moments before they stopped responding. /var/log/unattended-upgrades/unattended-upgrades.log 2013-07-02 06:30:51,875 INFO Starting unattended upgrades script 2013-07-02 06:30:51,875 INFO Allowed origins are: ['o=Ubuntu,a=precise-security'] 2013-07-02 06:33:57,771 INFO Packages that are upgraded: accountsservice apache2 apache2-mpm-prefork apache2-utils apache2.2-bin apache2.2-common apparmor apport apt apt-transport-https apt-utils bind9-host binutils dbus dnsutils gnupg gpgv isc-dhcp-client isc-dhcp-common krb5-locales libaccountsservice0 libapt-inst1.4 libapt-pkg4.12 libbind9-80 libc-bin libc-dev-bin libc6 libc6-dev libcurl3-gnutls libdbus-1-3 libdbus-glib-1-2 libdns81 libdrm-intel1 libdrm-nouveau1a libdrm-radeon1 libdrm2 libexpat1 libfreetype6 libgc1c2 libgnutls-dev libgnutls-openssl27 libgnutls26 libgnutlsxx27 libisc83 libisccc80 libisccfg82 liblwres80 libruby1.8 libx11-6 libx11-data libxcb1 libxext6 libxml2 linux-firmware linux-image-virtual linux-libc-dev linux-virtual multiarch-support openssl perl perl-base perl-modules python-apport python-crypto python-keyring python-problem-report python-software-properties ri1.8 ruby1.8 ruby1.8-dev sudo tzdata update-manager-core 2013-07-02 06:33:57,772 INFO Writing dpkg log to '/var/log/unattended-upgrades/unattended-upgrades-dpkg_2013-07-02_06:33:57.772399.log' 2013-07-02 06:36:10,584 INFO All upgrades installed I'm running Ubuntu 12.04 on Amazon EC2 servers. I have unattended-upgrades installed and configured as follows: /etc/apt/apt.conf.d/50unattended-upgrades // Automatically upgrade packages from these (origin:archive) pairs Unattended-Upgrade::Allowed-Origins { "${distro_id}:${distro_codename}-security"; // "${distro_id}:${distro_codename}-updates"; // "${distro_id}:${distro_codename}-proposed"; // "${distro_id}:${distro_codename}-backports"; }; // List of packages to not update Unattended-Upgrade::Package-Blacklist { }; /etc/apt/apt.conf.d/20auto-upgrades APT::Periodic::Update-Package-Lists "1"; APT::Periodic::Unattended-Upgrade "1"; I've struggled to find documentation about what happens to running processes during an upgrade. - Is this expected behaviour? Or should unattended-upgrades restart apache after upgrading it? - What can I do to ensure apache is restarted correctly? Should I just blacklist the apache package?

  Read the article

• Installing Yaws server on Ubuntu 12.04 (Using a cloud service)

  - by Lee Torres

  I'm trying to get a Yaws web server working on a cloud service (Amazon AWS). I've compilled and installed a local copy on the server. My problem is that I can't get Yaws to run while running on either port 8000 or port 80. I have the following configuration in yaws.conf: port = 8000 listen = 0.0.0.0 docroot = /home/ubuntu/yaws/www/test dir_listings = true This produces the following successful launch/result: Eshell V5.8.5 (abort with ^G) =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Using config file /home/ubuntu/yaws.conf =INFO REPORT==== 16-Sep-2012::17:21:06 === Ctlfile : /home/ubuntu/.yaws/yaws/default/CTL =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Listening to 0.0.0.0:8000 for <3> virtual servers: - http://domU-12-31-39-0B-1A-F6:8000 under /home/ubuntu/yaws/www/trial - =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Listening to 0.0.0.0:4443 for <1> virtual servers: - When I try to access the the url (http://ec2-72-44-47-235.compute-1.amazonaws.com), it never connects. I've tried using paping to check if port 80 or 8000 is open(http://code.google.com/p/paping/) and I get a "Host can not be resolved" error, so obviously something isn't working. I've also tried setting the yaws.conf so its at Port 80, appearing like this: port = 8000 listen = 0.0.0.0 docroot = /home/ubuntu/yaws/www/test dir_listings = true and I get the following error: =ERROR REPORT==== 16-Sep-2012::17:24:47 === Yaws: Failed to listen 0.0.0.0:80 : {error,eacces} =ERROR REPORT==== 16-Sep-2012::17:24:47 === Can't listen to socket: {error,eacces} =ERROR REPORT==== 16-Sep-2012::17:24:47 === Top proc died, terminate gserv =ERROR REPORT==== 16-Sep-2012::17:24:47 === Top proc died, terminate gserv =INFO REPORT==== 16-Sep-2012::17:24:47 === application: yaws exited: {shutdown,{yaws_app,start,[normal,[]]}} type: permanent {"Kernel pid terminated",application_controller," {application_start_failure,yaws,>>>>>>{shutdown,>{yaws_app,start,[normal,[]]}}}"} I've also opened up the port 80 using iptables. Running sudo iptables -L gives this output: Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT tcp -- ip-192-168-2-0.ec2.internal ip-192-168-2-16.ec2.internal tcp dpt:http ACCEPT tcp -- 0.0.0.0 anywhere tcp dpt:http ACCEPT all -- anywhere anywhere ctstate RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:http ACCEPT tcp -- anywhere anywhere tcp dpt:http Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination In addition, I've gone to the security group panel in the Amazon AWS configuration area, and add ports 80, 8000, and 8080 to ip source 0.0.0.0 Please note: if you try to access the URL of the virtual server now, it likely won't connect because I'm not running currently running the yaws daemon. I've tested it when I've run yaws either through yaws or yaws -i Thanks for the patience

  Read the article

• Having troubles connectiong Magento to external Windows Database Server using Windows Azure

  - by Kevin H

  "I tried to make this easy to read through" I am using Ubuntu 12.04 LTS for Magento and installed these commands onto the system: sudo apt-get install apache2 sudo apt-get install php5 libapache2-mod-php5 sudo apt-get install php5-mysql sudo apt-get install php5-curl php5-mcrypt php5-gd php5-common sudo apt-get install php5-gd I used Windows Server 2008 R2 August 2012 for Mysql Server For a reference, I used http://www.windowsazure.com/en-us/manage/windows/common-tasks/install-mysql/ When the server was setup, I added an empty disk to it Then, I added endpoints 3306 Next I accessed the server remotely After that, I formatted the empty disk and was inserted as F: Next I downloaded Mysql from http://*.mysql.com version Windows (x86, 64-bit), MSI Installer 5.5.28 In the installation process, I used these settings: Typical Setup - Clicked Next, install, next Chose Detailed Configuration - Clicked next Chose Dedicated MySQL Server Machine - Clicked Next Chose Transactional Database Only - Clicked Next Chose the "F:" Drive - Clicked Next Chose Online Transactional Processing (OLTP) - Clicked Next For Networking Options, I checkmarked 'Enable TCP/IP Networking" 'Add firewall exception for this port' 'Enable Strict Mode' - Clicked Next Chose Standard Character Set - Clicked Next For Windows Options, I checkedmarked 'Install as Window Service" 'Launch the MySQL Server automatically' 'Include Bin Directory in Windows PATH - Clicked Next For Security Options, I checkmarked 'Modify Security Settings' and set root password - Clicked Next Finally clicked Execute and Finish These are the Firewall Setting that I set I clicked inbound rules Properties Scope Allow IP Address and used the internal Address for Magento Server Clicked Apply and exited Next, I opened up MySQL 5.x Command Line Client Entered Root Password Then entered these commands mysql create database magento; mysql Create user magentouser identified by 'password'; mysql Grant select, insert, create, alter, update, delete, lock tables on magento.* to magentouser mysql exit Finally, I opened up the Magento Downloader Magento validation has approved all PHP version is right. Your version is 5.3.10-1ubuntu3.4. PHP Extension curl is loaded PHP Extension dom is loaded PHP Extension gd is loaded PHP Extension hash is loaded PHP Extension iconv is loaded PHP Extension mcrypt is loaded PHP Extension pcre is loaded PHP Extension pdo is loaded PHP Extension pdo_mysql is loaded PHP Extension simplexml is loaded These are all installed on Magento Server For the Database Connection, I used: The Database server only has MySQL 5.5 Server installed on it Host - Internal IP address User Name - The User I created when setting up database Password - The Password I created when setting up database For the password, I did some research and found out that Magento only accepts alphanumeric, so I went and set it up again and used only alphanumeric for the User password Now, I am still getting Accessed denied for database Connection. Also, I have tryed to setup mysql on independant Linux Server but kept getting errors. When, I found the solution. Wouldn't work, so I decided to try Windows. These is the questions, I have been asking and researching to debug this issue Is it because I am using Linux for magento and Windows for Database. I have had no luck in finding a reason why this wouldn't work There must be something, I am missing I also researched the difference between linux sql databases and windows sql databases but have not come to conclusion, if installing Mysql on windows would make a difference in syntax and coding. I have spent a lot of time looking into this and need some help with direction on how to complete my project. Any type of help would be appreciated.

  Read the article

• Email delivery management grievances

  - by joxl

  The question I have may be more of principle than anything else, but here's my dilemma. I manage an email system for a small company (about 20 email users). We own a plain-letter .com domain name through Network Solutions. Our email service is hosted by Google Apps. Recently (Feb. 2011) we've been having customers report that they aren't getting our emails. Upon further investigation it seems that the failed emails are all to a common (well known) domain. We have not received any bounce messages for the emails. We've also contacted a few of the intended recipients, who have reported that the messages are not in their spam box; they simply did not receive anything. In these cases we re-sent the same email to an alternate address on another domain, which was successful received. One customer contacted their email provider about the issue. The provider recommended that we submit a form to be white-listed by their domain. Here's where my problem begins. I feel like this is heading down a slippery slope. Doesn't this undermine the very principle of email? If this is the appropriate action to take in these situations where will it end? In theory (following this model) it could be argued that eventually one will first need to "whitelist" (or more appropriately termed "authenticate") themselves with an email host before actually sending any messages. More to this point, what keeps the "bad" spammers from doing the same thing...? We've just gone full circle. I know avoiding anti-spam measures is a big cat-and-mouse game, but I think this is the wrong way of "patching" the problem. Email standards say that messages should not just disappear silently. I have a problem supporting a model that says "you must do < this to make sure your emails aren't ignored". I have a notion to call the provider and voice my complaint, although I have a feeling it will probably fall on deaf ears. Am I missing something here? Is this an acceptable approach to email spam problems? What should I do?

  Read the article

• TeamSpeak 3 Disconnects

  - by ArchUser

  I've recently had a few random TS3 mass disconnects and I'm am curious to know where I may find any applications that can help me determine the cause of any types of TS3 server disconnections as we plan on having many more users in the future. I run an almost empty VPS (OpenVZ) server with an ArchLinux template on it. I have 1.5/2GB of RAM, 2GHz of CPU and plenty of hard drive space, to run for the most part, just my TS3 and a low traffic apache web server. This is what I am investigating. 2011-02-04 06:07:05.130343|INFO |VirtualServer | 1| client disconnected 'Valamoor'(id:224) reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.131338|INFO |VirtualServer | 1| client disconnected 'Kevrow'(id:19? reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.191849|INFO |VirtualServer | 1| client disconnected 'scuba'(id:200) reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.192633|INFO |VirtualServer | 1| client disconnected '[Ash] Setna'(id:75) reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.193350|INFO |VirtualServer | 1| client disconnected 'Akiris'(id:254) reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.194047|INFO |VirtualServer | 1| client disconnected 'Marcus'(id:25? reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.194726|INFO |VirtualServer | 1| client disconnected 'Guthry'(id:275) reason 'reasonmsg=connection lost' 2011-02-04 07:18:50.327071|INFO |VirtualServer | 1| client disconnected 'Valamoor'(id:224) reason 'reasonmsg=connection lost' 2011-02-04 07:18:51.339018|INFO |VirtualServer | 1| client disconnected 'Marcus'(id:25? reason 'reasonmsg=connection lost' 2011-02-04 07:18:51.339870|INFO |VirtualServer | 1| client disconnected '[Ash] Setna'(id:75) reason 'reasonmsg=connection lost' 2011-02-04 07:18:51.340515|INFO |VirtualServer | 1| client disconnected 'Guthry'(id:275) reason 'reasonmsg=connection lost' 2011-02-05 04:55:20.797353|INFO |VirtualServer | 1| client disconnected 'JohnyRingo'(id:240) reason 'reasonmsg=connection lost' 2011-02-05 04:55:20.798517|INFO |VirtualServer | 1| client disconnected 'Maloo roots'(id:196) reason 'reasonmsg=connection lost' 2011-02-05 04:55:20.799314|INFO |VirtualServer | 1| client disconnected 'Cpt dravyn'(id:234) reason 'reasonmsg=connection lost' 2011-02-05 04:55:20.839254|INFO |VirtualServer | 1| client disconnected 'scuba'(id:200) reason 'reasonmsg=connection lost' etc... I need to determine if it is my hosting provider or my server, and what tools I can use to determine the issues. My VPS host has told me this... "I checked out the node that your VPS runs on and there is no abnormal system load, or I/O wait from the drive. I also checked the bandwidth history from the server and there have been no spikes or outages."

  Read the article

• Slow wifi from Windows Server 2003 virtualized in XenServer

  - by John Clayton

  I'm a brand spanking new user of OS X, coming from a lifetime of Windows use. I've been setting up my new Macbook Pro and have run into a very unusual problem. Over wifi, I am unable to copy files to or from my Windows Home Server. The problem seems to exist only over wifi, and only to WHS. Here are the details of my setup: 2010 Macbook Pro (Core i7), OS X 10.6.3 Windows Home Server PP3 (virtualized in XenServer 5.5) Windows 7 Ultimate x64 desktop Windows 7 Ultimate x64 in Boot Camp D-Link DIR-655 wireless N router Here is what I've done to narrow down the problem: Files copy fine from WHS to OS X when using gigabit ethernet Files copy fine from desktop to OS X when using gigabit ethernet Files fail to copy from WHS to OS X when using wifi (error -51) Files copy fine from desktop to OS X when using wifi Files copy fine from WHS to Boot Camp when using wifi Files copy fine from desktop to Boot Camp when using wifi From what I can tell, it seems to be some sort of issue between OS X and WHS, but I can't for the life of me see what would be different between shares on WHS and my desktop. They are both connected using smb://ADDRESS (I've tried both by IP and name). I can browse the shares on the WHS, but copying to OS X fails. I originally found the issue while installing VS2010 off an ISO from WHS, mounted to a Windows 7 VM using VMware Fusion. During the installation the VM was unusable - even the clock got behind the host be about 8 minutes. Once I plugged in the ethernet and disabled the wifi things picked up and finished quickly. The Fusion 3.1 RC is the only I think of that I installed that may have messed with the wifi driver. I've also tried resetting the wifi router, and have changed it from being G & N to N-only. Under Boot Camp I get similar speeds as my wife's N laptop. Any ideas? Thanks! Update: The issue has been further narrowed down to Windows Server 2003, which Windows Home Server is based on, running in XenServer with the XenServer tools installed.

  Read the article

• How to unlock and remove a protected partition from Prestigio USB stick?

  - by mr.b

  Ok, so, I have one of those fancy schmancy devices, which is given to me by a frustrated friend of mine. Device is a Prestigio Leather 8GB, which identifies itself to Linux host as: Bus 001 Device 006: ID 1307:0165 Transcend Information, Inc. 2GB/4GB Flash Drive Kernel messages as USB device is plugged in: kernel: [ 2769.580042] usb 1-9: new high speed USB device using ehci_hcd and address 7 kernel: [ 2769.714782] scsi8 : usb-storage 1-9:1.0 kernel: [ 2770.713937] scsi 8:0:0:0: Direct-Access 8192MB flash drive 1.00 PQ: 0 ANSI: 2 kernel: [ 2770.714535] scsi 8:0:0:1: Direct-Access 8192MB flash drive 1.00 PQ: 0 ANSI: 2 kernel: [ 2770.715734] sd 8:0:0:0: Attached scsi generic sg3 type 0 kernel: [ 2770.716108] sd 8:0:0:1: Attached scsi generic sg4 type 0 kernel: [ 2770.722175] sd 8:0:0:0: [sdc] 962560 512-byte logical blocks: (492 MB/470 MiB) kernel: [ 2770.722657] sd 8:0:0:0: [sdc] Write Protect is on kernel: [ 2770.731078] sd 8:0:0:1: [sdd] 14012416 512-byte logical blocks: (7.17 GB/6.68 GiB) kernel: [ 2770.731215] sdc: kernel: [ 2770.738251] sd 8:0:0:1: [sdd] Write Protect is off kernel: [ 2770.880328] kernel: [ 2770.885876] sd 8:0:0:0: [sdc] Attached SCSI removable disk kernel: [ 2770.887442] sdd: unknown partition table kernel: [ 2771.049605] sd 8:0:0:1: [sdd] Attached SCSI removable disk So, symptoms are typical for U3-like devices: two separate devices inside of a single flash device. Windows sees it also as two identical usb devices, and mounts two separate drives to system, whereas first one presents itself as a CDROM device, holding a write-protected content, and second is a regular flash-disk partition, that "can" be written to. However, it seems like it's broken in some weird way, since it won't let me write anything to it, format it, nothing, but that's not the issue right now. Question: How can I unlock entire USB stick so it appears to system as a single, 8GB device which can be partitioned and used normally, without restrictions? Since it appeared to be an U3 device, I have tried standard utilities: both U3 Uninstaller by u3.com (found on SoftPedia), and opensource u3_tool from sourceforge (on both Windows and Linux). First utility failed to even detect USB stick as U3 device (simply stood idle while I re-plugged stick several times), while second tool failed with some obscure error about SCSI command unable to do something (I might be able to provide exact errors when I switch back to windows). u3_tool -i /dev/sg3 (Display device info) fails with u3_partition_info() failed: Device reported command failed: status 1 ...and every other option fails with same error, minus first part which states which command precisely has failed. So, apparently, this isn't a U3 device. Or, if it is, it doesn't behave like one. I read on a few occasions that this device protection is done by special command sent to device which tells it to lock itself, and so there should be an unlock command, that would set drive straight. Does anyone have any idea about what could I do to this device to fix it? P.S. I also mentioned a problem with being unable to use second "drive", but I'll tackle that problem when (and if) I manage to merge those two devices into one...

  Read the article

• Vagrant reporting VirtualBox guest additions out of date

  - by DTest

  Fairly new to Vagrant, so bear with me if I don't understand the process. I downloaded a CentOS box off http://www.vagrantbox.es/ Started it up running VirtualBox 4.2.4 and got this message: [default] The guest additions on this VM do not match the install version of VirtualBox! This may cause things such as forwarded ports, shared folders, and more to not work properly. If any of those things fail on this machine, please update the guest additions and repackage the box. Guest Additions Version: 4.0.8 VirtualBox Version: 4.2.4 So I used the vbguest plugin to update the guest additions, then repackaged the box as suggested. Having replaced the old box and loading it up I get the same message about guest additions being outdated, but vbguest reports that they are up to date (the automatic vbguest update is disabled in my Vagrantfile): Vagrant::Config.run do |config| config.vm.box = "centos56_64" config.vbguest.auto_update = false config.vbguest.no_remote = true end And the commands: dtest$ vagrant up [default] Importing base box 'centos56_64'... [default] The guest additions on this VM do not match the install version of VirtualBox! This may cause things such as forwarded ports, shared folders, and more to not work properly. If any of those things fail on this machine, please update the guest additions and repackage the box. Guest Additions Version: 4.0.8 VirtualBox Version: 4.2.4 [default] Matching MAC address for NAT networking... [default] Clearing any previously set forwarded ports... [default] Forwarding ports... [default] -- 22 => 2222 (adapter 1) [default] Creating shared folders metadata... [default] Clearing any previously set network interfaces... [default] Booting VM... [default] Waiting for VM to boot. This can take a few minutes. [default] VM booted and ready for use! [default] Mounting shared folders... [default] -- v-root: /vagrant dtest$ vagrant vbguest --no-install [default] Detected Virtualbox Guest Additions 4.2.4 --- OK. [default] Virtualbox Guest Additions on host: 4.2.4 - guest's version is 4.2.4 Since they appear to be updated after an install, I could ignore the message. But is it possible to get rid of it?

  Read the article

• Sysadmin 101: How can I figure out why my server crashes and monitor performance?

  - by bflora

  I have a Drupal-powered site that seems to have neverending performance problems. It was butt-slow about 5 months ago. I brought in some guys who installed nginx for anonymous visitors, ajaxified a few queries so they wouldn't fire during page load, and helped me find a few bottlenecks in the code. For about a month, the site was significantly faster, though not "fast" by any stretch of the word. Meanwhile, I'm now shelling out $400/month to Slicehost to host a site that gets less than 5,000/uniques a day. Yes, you read that right. Go Drupal. Recently the site started crashing again and is slow again. I can't afford to hire people to come in, study my code from top to bottom, and make changes that may or may not help anymore. And I can't afford to throw more hardware at the problem. So I need to figure out what the problem is myself. Questions: When apache crashes, is it possible to find out what caused it to crash? There has to be a way, right? If so, how can I do this? Is there software I can use that will tell me which process caused my server to die? (e.g. "Apache crashed because someone visited page X." or "Apache crashed because you were importing too many RSS items from feed X.") There's got to be a way to learn this, right? What's a good, noob-friendly way to monitor my current apache performance? My developer friends tell me to "just use Top, dude," but Top shows me a bunch of numbers without any context. I have no clue what qualifies as a bad number or a good number in Top, or which processes are relevant and which aren't. Are there any noob-friendly server monitoring tools out there? Ideally, I could have a page that would give me a color-coded indicator about how apache is performing and then show me a list of processes or pages that are sucking right now. This way, I could know when performance is bad and then what's causing it to be so bad. Why does PHP memory matter? My apparently has a 30MB memory foot print. Will it run faster if I bring that number down? Thanks for any advice. I spent a year or so trying to boost my advertising income so I could hire a contractor to solve my performance woes. I didn't want to have to learn all this sysadmin voodoo. I'm now resigned to the fact that might not have a choice.

  Read the article

• ubuntu eth0 not reconnecting after cable unplugged

  - by Alex

  I'm running kubuntu 9.10 w/ gnome, I have a static IP defined in /etc/network/interfaces When I unplugged my network cable and rebooted, then reconnected the network cable I was not able to connect. I tried using sudo ifup eth0, and then ifconfig and it seemed as though the IP address had been assigned and I was connected, but I wasn't. I then did ifdown eth0, and again ifup eth0. For some reason I'm not able to access the network. Furthermore, I also attempted to connect via wlan, and was able to connect to the wireless network, but cannot "see" the network. I can't transfer data or access the internet or anything on the network including the router. How do I resolve this? topsy@monolyth:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1c:25:1c:df:70 inet addr:192.168.1.145 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:25ff:fe1c:df70/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5720 errors:0 dropped:0 overruns:0 frame:0 TX packets:565 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:378035 (378.0 KB) TX bytes:46832 (46.8 KB) Memory:fe000000-fe020000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240 (240.0 B) TX bytes:240 (240.0 B) By access the network I mean the local network as well as the internet. topsy@monolyth:~$ ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=9.14 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=1.24 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=1.01 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=1.00 ms [snip... all OK, icmp_seq from 5-30, time between 0.981-1.25ms] ^C --- 192.168.1.1 ping statistics --- 30 packets transmitted, 30 received, 0% packet loss, time 29035ms rtt min/avg/max/mdev = 0.971/1.300/9.140/1.458 ms topsy@monolyth:~$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default 192.168.1.1 0.0.0.0 UG 100 0 0 eth0 root@monolyth:~# cat /etc/resolv.conf # Generated by NetworkManager

  Read the article

• Areca 1280ml RAID6 volume set failed

  - by Richard

  Today we hit some kind of worst case scenario and are open to any kind of good ideas. Here is our problem: We are using several dedicated storage servers to host our virtual machines. Before I continue, here are the specs: Dedicated Server Machine Areca 1280ml RAID controller, Firmware 1.49 12x Samsung 1TB HDDs We configured one RAID6-set with 10 discs that contains one logical volume. We have two hot spares in the system. Today one HDD failed. This happens from time to time, so we replaced it. Upon rebuilding a second disc failed. Normally this is no fun. We stopped heavy IO-operations to ensure a stable RAID rebuild. Sadly the hot-spare disc failed while rebuilding and the whole thing stopped. Now we have the following situation: The controller says that the raid set is rebuilding The controller says that the volume failed It is a RAID 6 system and two discs failed, so the data has to be intact, but we cannot bring the volume online again to access the data. While searching we found the following leads. I don't know whether they are good or bad: Mirroring all the discs to a second set of drives. So we would have the possibility to try different things without loosing more than we already have. Trying to rebuild the array in R-Studio. But we have no real experience with the software. Pulling all drives, rebooting the system, changing into the areca controller bios, reinserting the HDDs one-by-one. Some people are saying that the brought the system online by this. Some are saying that the effect is zero. Some say, that they blew the whole thing. Using undocumented areca commands like "rescue" or "LeVel2ReScUe". Contacting a computer forensics service. But whoa... primary estimates by phone exceeded 20.000€. That's why we would kindly ask for help. Maybe we are missing the obvious? And yes of course, we have backups. But some systems lost one week of data, thats why we'd like to get the system up and running again. Any help, suggestions and questions are more than welcome.

  Read the article

• Showing Directory Root When Launching Rails App Using Apache2 and Passenger

  - by LightBe Corp

  I have done the following in an attempt to host a Rails 3.2.3 application using Apache 2.2.21 and Passenger 3.0.13: Installed gem Passenger rvmsudo passenger-install-apache2-module Added website info in /etc/apache2/extra/httpd-vhosts.conf Added line to /etc/hosts (not sure if this was needed or not; not mentioned in Passenger documentation Uncommented out the line in /etc/apache2/httpd.conf to Include /etc/apache2/extra/httpd-vhosts.conf Restarted Apache When I try to pull up my website the following displays: Index of / Name Last modified Size Description Apache/2.2.21 (Unix) mod_ssl/2.2.21 OpenSSL/0.9.8r DAV/2 PHP/5.3.10 with Suhosin-Patch Phusion_Passenger/3.0.13 Server at lightbesandbox2.com Port 443 Here is /etc/hosts entry for the website: 127.0.0.1 www.lightbesandbox2.com Here is my /etc/apache2/extra/httpd-vhosts.conf entry for the website: NameVirtualHost *:80 <VirtualHost *:80> ServerName www.lightbesandbox2.com ServerAlias lightbesandbox2.com PassengerAppRoot /Users/server1/Sites/iktusnetlive_RoR/ DocumentRoot /Users/server1/Sites/iktusnetlive_RoR/public <Directory /Users/server1/Sites/iktusnetlive_RoR/public> AllowOverride all Options -MultiViews </Directory> </VirtualHost> When I do rvmsudo passenger-status I get the following output: ----------- General information ----------- max = 6 count = 1 active = 0 inactive = 1 Waiting on global queue: 0 ----------- Application groups ----------- /Users/server1/Sites/iktusnetlive_RoR/: App root: /Users/server1/Sites/iktusnetlive_RoR/ * PID: 8140 Sessions: 0 Processed: 2 Uptime: 20m 51s None of my assets are in the public folder in my Rails app. I have written an application using the template presented in Michael Hartl's Ruby on Rails Tutorial. The home page is in /app/views/static_pages/home.html.erb. I decided to copy an index.html file in the public folder to see if it would display. It displayed as I had hoped.. Is there a way to get Passenger to find my assets without me having to rewrite my application? Any help would be appreciated. Update 6/23/2012 10:00 am CDT GMT-6 I corrected the problems with my file and have successfully executed the rake assets:precompile command. I still get the index page as before. I have made no other changes. I did a passenger-status command and it is still loaded. Restarting Apache did nothing.

  Read the article

• Hylafax / Capi4hylafax: faxgetty does not recognize number of lines

  - by Wrikken

  We've got a T.30 card, 30 working lines on it, but for some reason, if I add more then 30 faxes in the queue at any time (and we're busy enough at peak times that this happens a lot), faxgetty sends faxes to non-existent lines and they appear in the error queue as a 'busy' signal on the line, which results in a lot of failed faxes because the counter of max 3 tries increases rapidly. This is using faxgetty (USE_FAXGETTY="y" in /etc/default/hylafax). I've inherited this thing, so I'm not entirely sure how faxgetty is supposed to know the number of lines. However, if I alter the script to faxmodem (USE_FAXGETTY="n" in /etc/default/hylafax and manually enabling 30 modems), this behavior goes away (new faxes 'wait' for a line to be available before trying to send, so each try / fail is a valid one on a working line, majorly descreasing the amount of failed faxes. However, when researching this almost anyone talks about faxgetty being the preferred, more robust, method, and on top of that for some unexplained reason all FIFO's disappeared for some reason after several errorless hours with faxmodem, forcing a hylafax restart using faxgetty until we figured out why this faxmodem solution failed (which is another question, and somewhat out of scope here). Environment: Debian 2.6.26-2-amd64 capi4hylafax 1:01.03.00.99.svn.300-12 hylafax-client 2:4.4.4-10.1 hylafax-server 2:4.4.4-10.1 Config --hfaxd.conf-- LogFacility: daemon ServerTracing: 0x1ff --hyla.conf-- Host: localhost Verbose: No VRes: 196 TimeZone: local DialRules: "/etc/hylafax/dialrules.europe" --/etc/hylafax/config -- InternationalPrefix: 00 LongDistancePrefix: 0 AreaCode: 99999 CountryCode: 31 DialStringRules: "etc/dialrules.europe" ModemGroup: any:faxCAPI SendFaxCmd: "/usr/bin/wrapc2faxsend" --/etc/hylafax/config.faxCAPI -- SpoolDir: /var/spool/hylafax FaxRcvdCmd: /var/spool/hylafax/bin/faxrcvd PollRcvdCmd: /var/spool/hylafax/bin/pollrcvd FaxReceiveUser: uucp FaxReceiveGroup: dialout LogFile: /var/spool/hylafax/log/capi4hylafax #no, checking this log did not yield anything interesting LogTraceLevel: 4 LogFileMode: 0600 ModemGroup: any:faxCAPI #repeats of faxCAPI2 = faxCAPI30, with of course another devicename/local ident: { HylafaxDeviceName: faxCAPI RecvFileMode: 0600 FAXNumber: ****redacted**** LocalIdentifier: ****some-ident-per-device*** MaxConcurrentRecvs: 0 OutgoingController: 1 OutgoingMSN: SuppressMSN: 0 NumberPrefix: NumberPlusReplacer: "00" UseISDNFaxService: 0 RingingDuration: 0 { Controller: 1 AcceptSpeech: 0 UseDDI: 0 DDIOffset: DDILength: 0 IncomingDDIs: IncomingMSNs: AcceptGlobalCall: 1 } } So in short: How does faxgetty determine the number of lines available? (the man page isn't terribly revealing, and I can't find an appropriate setting in hylafax-config. And how can I get a capi4hylafax/hylafax setup which queues more faxes then lines are available correctly without immediately incrementing the fail count? We will not be receiving any faxes on this machine b.t.w. As I said, I've inherited this thing, so if there are important configuration options I'm not including, please let me know.

  Read the article

< Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >