Search Results

Search found 15209 results on 609 pages for 'configuration'.

Page 462/609 | < Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >

• Windows 7 - "A disk read error occured. Press Ctrl + Alt + Del to restart"

  - by Senthil

  Problem: When I switch on my PC, after BIOS POST, a cursor is blinking for about 5 seconds and then I am getting this error message: A disk read error occurred. Press Ctrl + Alt + Del to restart. I am able to go into BIOS. But Windows loader doesn't even start. This message is shown after my motherboard logo comes and goes. Symptoms: I DID notice my system freezing for minutes at a time for past two days. Also, in the past two days, it stopped half way through the Window booting process. I had to do hard reset couple of times to get it working. But since today morning, I only get this error message. Configuration: Operating System: Windows 7 Ultimate 32-bit only. Hard disk: 1 Physical Disk - 80GB SATA Partitions: Two (2) - C: and D: File System: NTFS No drive encryption or compression is turned on. After I searched on the net, I have found people mentioning these possible causes: Hard Disk is physically failing Corrupt MBR Bad Sector I am planning to buy a new hard disk, install Windows on it and continue. But I need data from the old hard disk. The data I want is in D: drive, outside any Windows user folder, is not encrypted or compressed or protected in anyway. I think if someone/something can get the disk working again and knows NTFS, the data can be hopefully read. What steps should I follow to recover files from the defective disk? Update: I bought a new disk, installed windows on it and added the defective one as a slave. Then I was able to read the data from the defective hard disk. Though chkdsk found lots of errors, the files I wanted were not affected and I got them back :) I am not using that hard disk anymore though it seems to be working at the moment.

  Read the article

• Mplayer no sound when playing some movies

  - by Ivan Peevski

  Ok, that's a bit of a strange problem, that somehow crept into my system. It used to work fine. Here is the problem as far as I can identify it. When I try to play certain video files with mplayer, there is no sound. As far as I can tell, it is only an issue with ac3 and dts sound tracks (using the ffmpeg decoder). Mplayer says: ========================================================================== Opening audio decoder: [ffmpeg] FFmpeg/libavcodec audio decoders AUDIO: 48000 Hz, 6 ch, s16le, 1536.0 kbit/33.33% (ratio: 192000->576000) Selected audio codec: [ffdca] afm: ffmpeg (FFmpeg DTS) ========================================================================== [AO_ALSA] Playback open error: Device or resource busy Failed to initialize audio driver 'alsa' Could not open/initialize audio device -> no sound. Audio: no sound (similar with ac3 sound, but using the ffac3 audio codec). Trying different audio output (-ao oss/pcm/sdl) doesn't fix the problem. The strange thing is that if I play these files directly with ffplay, they work fine. mplayer sound with mp3/ogg is fine My alsa configuration is standard (no /etc/asound.conf or ~/.asound*) OS: Linux Gentoo Mplayer: 1.0_rc4_p20100213 (SVN-r30554-4.3.4) FFMpeg: 0.5_p20601-r1 (SVN-r20601) Any other information I can provide?

  Read the article

• How to rip AVI from VOB using ffmpeg

  - by Linux Jedi

  I am trying to convert a VOB to an AVI. I have ripped an AVI from this VOB before using ffmpeg, but for some reason it's not working this time. This is what I tried: ffmpeg -sameq -acodec copy -i VTS_01_2.VOB output.avi This is the output I get: FFmpeg version 0.6.1, Copyright (c) 2000-2010 the FFmpeg developers built on Dec 29 2010 18:02:10 with gcc 4.2.1 (Apple Inc. build 5664) configuration: libavutil 50.15. 1 / 50.15. 1 libavcodec 52.72. 2 / 52.72. 2 libavformat 52.64. 2 / 52.64. 2 libavdevice 52. 2. 0 / 52. 2. 0 libswscale 0.11. 0 / 0.11. 0 [mpeg2video @ 0x101014200]mpeg_decode_postinit() failure Last message repeated 6 times Input #0, mpeg, from 'VTS_01_2.VOB': Duration: 26:30:29.20, start: 140.171311, bitrate: 90 kb/s Stream #0.0[0x1e0]: Video: mpeg2video, yuv420p, 720x480 [PAR 32:27 DAR 16:9], 9800 kb/s, 31.44 fps, 29.97 tbr, 90k tbn, 59.94 tbc Stream #0.1[0xa0]: Audio: pcm_s16be, 48000 Hz, 2 channels, s16, 1536 kb/s Output #0, avi, to 'output.avi': Metadata: ISFT : Lavf52.64.2 Stream #0.0: Video: mpeg4, yuv420p, 720x480 [PAR 32:27 DAR 16:9], q=2-31, 200 kb/s, 29.97 tbn, 29.97 tbc Stream #0.1: Audio: pcm_s16be, 48000 Hz, 2 channels, 1536 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Could not write header for output file #0 (incorrect codec parameters ?)

  Read the article

• DNS setup problems with Windows Azure VPS

  - by jbigelow

  What is the proper to setup the A record (or CNAME) for a Windows Azure VPS? I can't connect to my website after setting up IIS and believe I don't have the correct DNS setup. I created a small VPS instance with the default Windows Server 2012 configuration. I RDP'd in and added the Webserver role. In my DNSMadeEasy control panel I added an A record with my Public Virtual IP Address. In IIS I went to the default website and added bindings for the hostname of my website, so I should be able to type mywebsite.com and see the IIS 8 splash screen, but instead my browser cannot connect. I attempted to navigate to the site by typing in my Virtual IP address into the browser and still cannot connect. I RDP'd back into the machine and turned off Windows Firewall. No change, still cannot navigate to my website. From within IIS I double checked my binding. If I click "browse *:80" I can bring up my website in IE with the http:// localhost address. If I click "browse mywebsite on *.80" IE says "This page cannot be displayed.", from within the RDP session I can view the site if I navigate to http:// 127.0.0.1 but not if I navigate to my Virtual IP, nor can I view the page if I try navigating to http:// mywebservername.cloudapp.net I'm thinking I must be fundamentally not understanding how do DNS setup with Azure VPS but my initial Google searches aren't turning up any helpful information. (spaces added after the http:// so serverfault doesn't try and render them as valid urls.)

  Read the article

• Exim 4 Virtual Domains and Catchall on Debian (Squeeze)

  - by parazuce

  Hello, I've been at it for about 4 hours now. Searching as well as trying different tutorials. Here's my setup: I have 2 domains, both under my own DNS server (MX records setup as well). I have exim4 successfully running, and it is able to send messages from both of those domains. I have tested this using sendmail, and manually setting the "From" attribute. Exim successfully delivers mail to users no matter which domain was specified. I'm fine with that, but I'm having an issue editing virtual domains, and adding custom delivery options (such as a catch all). I've been searching for about 4 hours, and I can't find any up-to-date documentation on how to do this. The old methods would be to add a line such as: domainlist local_domains = @:localhost:dsearch;/etc/exim4/virtual Once that line was added, I made a directory at /etc/exim4/virtual, then created files inside such as example.com which would then contain rules for delivery under that domain. This did not work, however. Searching further, I've found that exim no longer supports dsearch (I guess because they claim it never has?) This is where I'm stuck. I'm on a "split" configuration as well.

  Read the article

• Serving images from another hostname vs Apache overload for the rewrites

  - by luison

  We are trying to improve further the speed of some sites with older HTML in order as well to obtain better SEO results. We have now applied some minify measures, combined html, css etc. We use a small virtualized infrastructure and we've always wanted to use a light + standar http server configuration so the first one can serve images and static contents vs the other one php, rewrites, etc. We can easily do that now with a VM using the same files and conf of vhosts (bind mounts) on apache but with hardly any modules loaded. This means the light httpd will have smaller fingerprint that would allow us to serve more and quicker, have more minSpareServer running, etc. So, as browsers benefit from loading static content from different hostnames as well, we've thought about building a rewrite rule on our main server (main.com) to "redirect" all images and css *.jpg, *.gif, *.css etc to the same at say cdn.main.com thus the browser being able to have more connections. The question is, assuming we have a very complex rewrite ruleset already (we manually manipulate many old URLs for SEO) will it be worth? I mean will the additional load of main's apache to have to redirect main.com/image.jpg (I understand we'll have to do a 301) to cdn.main.com/image.jpg + then cdn.main.com having to serve it, be larger than the gain we would be archiving on the browser? Could the excess of 301s of all images on a page be penalized by google? How do large companies work this out, does the original code already include images linked from the cdn with absolute paths? EDIT Just to clarify, our concern is not to do so much with server performance or bandwith. We could obviously employ an external CDN server but we have plenty CPU and bandwith. Our concern is with how to have "old" sites with plenty semi-static HTML content benefiting from splitting connections for images and static content via apache without having to change the html to absolute paths (ie. image.jpg to cdn.main.com/image.jpg happening on the server not the code)

  Read the article

• DHCP not responding from laptop or router, but works on directly plugged PC?

  - by Matt H

  I'm at my sister in law's place in Singapore. I'm not from Singapore but am here for a few months. She has some sort of cable modem made by motorolla (SB5101 Surfboard). I think it goes, through starhub or similar provider. Anyhow, her PC is directly attached by cable (not wireless) and she can access the internet. There is no wireless router connected to it. The PC is configured with DHCP and appears to be working. However, the moment I unplug her PC and plug in my laptop, it doesn't get an address. The interesting thing here is that I also see this toredo tunnel adaptor etc. I'm not familiar with what that is. It appears to be being assigned an IP v6 address and an IP v4 address. I thought perhaps it's my laptop, but also when I plug in my DDWRT based router, it also fails to get a DHCP assigned address on the WAN port. I can't also seem to connect into any web configuration on the motorolla modem either. Any ideas? what kind of setup is this? all I'd like to do is plug in my wireless router so I can roam around the house and also access the internet.

  Read the article

• Lightweight Linux distro that includes developer tools? (or, the most BSD-like Linux)

  - by RevAaron

  I cut my teeth on Minix and Slackware 1.1, but I've been in the OS X Wilderness for the last few years. I'm trying to standardize on a Linux distribution for personal and work-related use on less powerful laptops and under virtualization. So far, NetBSD and OpenBSD are the best fit for my purposes- but after plenty of frustration I've come to the conclusion that I need to stick with Linux to get the hardware and software support that comes with it. What I like about NetBSD/OpenBSD that I'd like to keep: X, but no default KDE, GNOME or XFCE! A sensible /etc and dot file setup- startx calls xinit, xinit looks for ~/.xinitrc; nothing more complicated than that is needed. Command line tools and file-based configuration: I shouldn't need a GUI to connect to a WAP. Decent selection of binary packages; building from source is OK, but nothing source-only like Gentoo. pkg_add (BSD) and apt-get both have treated me well in the past. Modest RAM and HDD requirements: boot + X + awesome+ two xterms takes up 80 MB on OpenBSD and 240 MB on Debian 5 and Crunchbang In my experience, most "lightweight" and Live CDs focus on a nice desktop environment crammed into a CD or USB stick; once you add build-essentials you end up with something just about as bloated as Ubuntu or Debian full install. Crunchbang is a great example. Thanks in advance for all suggestions!

  Read the article

• django, mod_wsgi, MySQL High CPU - Problems

  - by Red Rover

  Good Evening, and thank you for reading this post. I am having a problem with Django after migrating the dB from SQLlite to MySQL. Initially, for the first 48hours, all ran well. But now we are experiencing high cpu about every 30 minutes. This is a production ESX4i VM host, with 2 x 2.8 ghz CPUs and 12 GB ram. I have allocated 4 cpu's to this VM and 4 GB memory. Any insight into this configuration and help with the spikes in CPU would be appreciated. IT is configured to use the prefork MPM. Outlined are the config's for the different services: MySQL Server version: 5.1.61 Source distribution Django 1.3 mod_wsgi Apache/2.2.15 httpd.conf Timeout 120 KeepAlive Off MaxKeepAliveRequests 400 KeepAliveTimeout 3 prefork MPM StartServers 8 MinSpareServers 8 MaxSpareServers 16 ServerLimit 40 MaxClients 40 MaxRequestsPerChild 0 worker MPM StartServers 16 MaxClients 1024 MinSpareThreads 64 MaxSpareThreads 256 ThreadsPerChild 64 MaxRequestsPerChild 10240 MySQL my.conf [mysqld] datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql symbolic-links=0 [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid my.cnf wsgi.conf LoadModule wsgi_module modules/mod_wsgi.so /etc/httpd/conf.d/wsgi.conf WSGISocketPrefix /var/run/wsgi WSGIPythonEggs /var/tmp WSGIDaemonProcess SITE maximum-requests=10000 WSGIProcessGroup SITE

  Read the article

• AMD FX8350 CPU - CoolerMaster Silencio 650 Case - New Water Cooling System

  - by fat_mike

  Lately after a use of 6 months of my AMD FX8350 CPU I'm experiencing high temperatures and loud noise coming from the CPU fan(I set that in order to keep it cooler). I decided to replace the stock fan with a water cooling system in order to keep my CPU quite and cool and add one or two more case fans too. Here is my case's airflow diagram: http://www.coolermaster.com/microsite/silencio_650/Airflow.html My configuration now is: 2x120mm intake front(stock with case) 1x120mm exhaust rear(stock with case) 1 CPU stock I'm planning to buy Corsair Hydro Series H100i(www.corsair.com/en-us/hydro-series-h100i-extreme-performance-liquid-cpu-cooler) and place the radiator in the front of my case(intake) and add an 120mm bottom intake and/or an 140mm top exhaust fan. My CPU lies near the top of the MO. Is it a good practice to have a water-cooling system that takes air in? As you can see here the front of the case is made of aluminum. Can the fresh air go in? Does it even fit? If not, is it wiser to get Corsair Hydro Series H80i (www.corsair.com/en-us/hydro-series-h80i-high-performance-liquid-cpu-cooler) and place the radiator on top of my case(exhaust) and keep the front 2x120mm stock and add one more as intake on bottom. If you have any other idea let me know. Thank you. EDIT: The CPU fan running ~3000rpm and temp is around 40~43C on idle and save energy. When temp is going over 55C when running multiple programs and servers on localhost(tomcat, wamp) rpm is around 5500 and loud! I'm running Win8.1 CPU not overclocked PS: Due to my reputation i couldn't post the links that was necessary. I will edit ASAP.

  Read the article

• Postfix: change sender in queued messages

  - by ring0

  Following a complete re-installation we got a problem with the configuration: the sender address was wrong and some recipients (mail servers) rejected them. So there is a bunch of mails stuck in the Postfix queue. Ideally, a change of the sender address directly in the queued mails, and then flushing the queue would be optimal. I tried this answer that addresses this very problem. But messages don't seem to be easily modifiable in the version I have (2.11.0). For instance there is no /var/spool/mqueue dir, but, instead, /var/spool/postfix/... active bounce corrupt defer deferred dev etc flush hold incoming lib maildrop pid private public saved trace usr and the dir of interest is deferred. I tried to modify a few files there changing the wrong domain with the correct one (and was careful to ensure only those were changed). But then, those mails were moved to corrupt, meaning that a simple text change doesn't seem to work (done with vi). Any other cleaner way to change the sender in queued mails?

  Read the article

• htaccess not properly rewriting urls

  - by Cameron Ball

  This is a bit of a weird one. I'm doing some work on a server, and I need rewrite rules for directories that actually exist (in some cases, they are more than one level deep) At the moment my .htaccess looks like this: RewriteEngine on RewriteRule ^simfiles/([-\ a-zA-Z0-9:/]+)$ http://mydomain.com/?portal=simfiles&folder=$1 [L] And this is working OK, for example, a url like: mydomain.com/sifmiles/my-files Will get redirected to mydomain.com/?portal=simfiles&folder=my-files Or in the case of a directory structure that is deeper than one level: mydomain.com/sifmiles/my-files/more-of-my-files Will get redirected to mydomain.com/?portal=simfiles&folder=my-files/more-of-my-files I wrote the regex so that it won't match things with a . in the path, because there are css and js files which reside in simfiles/somedirectory, and if I redirect everything then these cannot be loaded. I tried a configuration like this: RewriteEngine on RewriteCond %{REQUEST_FILENAME} !-f RewriteRule ^simfiles/([-\ a-zA-Z0-9:/\.]+)$ http://mydomain.com/?portal=simfiles&folder=$1 [L] But that doesn't work, things still don't load properly. So my first question is, how can I achieve this "properly"? I don't like my solution because it means redirects won't occur if the folder has a . in its name. My second problem, is that while the redirection is happening properly, the url becomes: http://mydomain.com/?portal=simfiles&folder=my-files I want the URL to remain clean, like: http://mydomain.com/sifmiles/my-files How can I achieve this?

  Read the article

• Windows Media Player 12 Library import keeps dying

  - by duckworth

  I cannot get WMP 12 to import my library. I have searched around various forums and tried all the common solutions like disabling Media Sharing, deleted my %LOCALAPPDATA%\Microsoft\Media Player directory and tried reimporting, etc. but nothing works. I have even removed the Media features from Windows setup and re-added them. I have a large mp3 collection shared on the network from another Windows box. I add the folder (tried as a mapped drive and UNC path) and it begins importing. After about 30 minutes into the import (the CurrentDatabase_372.wmdb hits just under 400MB) my WMP player stops importing and all of the icons in WMP turn to red x's and my library is gone. I close and reopen WMP 12 and the library is empty and the CurrentDatabase_372.wmdb is small and it strarts importing again. Rinse, lather, repeat. I am going nuts as WMP11 on Vista handles this same setup perfectly. I am at my wits end on what else to try. I am running a legit Windows 7 Ultimate X64 RTM install. Here is a screenshot of what WMP12 looks like when the import dies: Any other ideas? Edit: OK, I Just confirmed this is definitely a problem not specific to my computer or configuration. I just did a clean installation of Windows 7 Ultimate x86 on an old test machine, opened WMP12 and added the same network folder of mp3's and it crashed about an hour into the import with the same appearance as the screenshot I posted above and the library disappears. So the problem has to be one of several things: The large size of the library The fact that the library is on the network A specific file or file is causing it the player to crash

  Read the article

• PXE boot -- kernel not found on TFTP server

  - by user70523

  I followed the following link for PXE boot, http://www.howtoforge.com/setting-up-a-pxe-install-server-on-ubuntu-9.10-p3 and I was able to ping the client from the server and also when I booted up the client It is getting the IP address from the server. But later,I got this error PXELinux 3.82 2009-06-09 . . . [other informations] !PXE Entry point found (we hope) at 9D3B:0109 via plan A UNDI code segment at 9D3B len 16C2 UNDI data segment at 933B len A000 Getting cached packet 01 02 03 . . . [other informations] TFTP prefix: Trying to load: pxelinux.cfg/ec5db4c0-74fe-d511-b9e7-3d9235afe5a1 Trying to load: pxelinux.cfg/01-00-17-31-b6-5e-a8 Trying to load: pxelinux.cfg/0A64491E Trying to load: pxelinux.cfg/0A64491 Trying to load: pxelinux.cfg/0A6449 Trying to load: pxelinux.cfg/0A644 Trying to load: pxelinux.cfg/0A64 Trying to load: pxelinux.cfg/0A6 Trying to load: pxelinux.cfg/0A Trying to load: pxelinux.cfg/0 Trying to load: pxelinux.cfg/default Unable to locate configuration file Boot failed: press a key to retry or wait for reset I have put all the files mentioned in the link in tftpboot. Can anyone explain what could be the problem. Thanks in advance

  Read the article

• Windows 7 Black Screen On Boot, Seperate Bootable VHD Works Fine

  - by David Osborn

  I have a Window 7 x64 install with a bootable VHD (also Windows 7 x64). I was having problems getting my homeserver to do backups (VSS erred) so I ran check disk and used a tool from MS (cleanc2r.exe) to remove an empty Q drive from the VHD that I believe was a result of installing Office 2010 Beta. (All of this was done on the bootable VHD, not the main install.) Now I can't boot into the main install. It gets past the Starting Windows screen and then goes black. I can still boot into the bootable VHD and everything works fine from there. I have tried to boot the main install in Safe Mode/Safe Mode with Networking/and Safe Mode command prompt and it has the same issue. I ran chkdsk /r on the main install and after doing all the work there was a message about correcting some free space that was marked as allocated and also that it was unable to make an entry into the event log. I tried the startup repair utility and it found no problems. I don't see the setting for restore to last know good configuration so I couldn't do that. I don't recall installing anything new to the main install nor having hooked up any new hardware recently.

  Read the article

• A complicated nginx/php-fpm chroot setup

  - by Rsaesha

  I'm running nginx and php-fpm, and I want to set up jails for each host. My setup is a little complicated, so following tutorials on the web gets me nowhere. Each site has a directory /var/www/domain.name/ Inside that directory, there will be a public/ directory which will be the website root, a logs/ directory which will store nginx logs for that site specifically, and the chroot filesystem (etc/, usr/, etc.) The first problem I've run into is that nomatter how I configure it, PHP-FPM cannot find the files that are passed to it via nginx. They result in a "Primary script unknown" error, and to make matters worse, the error messages from PHP-FPM are no more verbose than that, so I can't figure out what path is being passed by nginx. A php-fpm pool configuration for a host looks like this: [host] user = host group = www-data chroot = /var/www/domain.name chdir = /public listen = 127.0.0.1:900x 'x' is incremented for each pool. The nginx config for this host looks like this: server { listen 80; server_name domain.name *.domain.name; root /var/www/domain.name/public; index index.php index.html index.html; location ~ \.php$ { expires epoch; fastcgi_split_path_info ^(.+\.php)(/.+)$; include fastcgi_params; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_pass 127.0.0.1:9001; } } I'm guessing that the problem is the SCRIPT_FILENAME parameter, but I've changed it to just $fastcgi_script_name, and various other combinations, but to no avail. Can anyone help?

  Read the article

• What can lead to a zone memory exhaustion and how Nginx reacts to it?

  - by Miles Hughes

  What is a possible scenario for exhausting the memory designated to a connection zone with limit_conn_zone directive and what are the implication in this case? Suppose I have this in my configuration: http { limit_conn_zone $binary_remote_addr zone=connzone:1m; ... server { limit_conn connzone 5; which, according to the documentation, allocates 16000 states for connzone on a 64-bit server. It also says that If the storage for a zone is exhausted, the server will return error 503 (Service Temporarily Unavailable) to all further requests. Well, Ok. But what does it mean on practice? When does this happen? Who receives those 503s? Does it mean that if the number of IPs somehow associated with connzone hits 16000 everyone gets a 503 and it's all over? How does Nginx decide? The documentation is weirdly vague on this. So, considering the example config, who would actually get a 503 and under which circumstances and how would things go from there? Same with request zones?

  Read the article

• Cannot set up dual monitors correctly in Fedora15 with KDE.

  - by adivasile

  I have 2 monitors: 24" LCD connected via DVI(primary) 19" LCD connected via VGA(secondary) Everytime Fedora starts the second display is always set to clone the first one and they both run at 1280x1024 and I always have to disable the 19" monitor, in order for the bigger one to run at 1920x1080. I want to set them up so that my secondary monitor extends the primary one.The problem is that no matter what kind of configuration I choose it has no effect.My secondary monitor remains disabled. I've tried using both the Display manager from KDE and the ATI Control Panel and the behaviour is always the same.The moment I click apply, the screen flickers and nothing changes. I've succesfully used the extended setup in Fedora15 with Gnome3. I have a RadeonHD 4300 series videocard and I'm using the drivers downloaded from the AMD site. This is the output of xrandr -q : Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 1920 x 1920 VGA-0 connected (normal left inverted right x axis y axis) 1280x1024 75.0 60.0 1280x960 60.0 1152x864 75.0 1024x768 75.0 70.1 66.0 60.0 832x624 74.6 800x600 72.2 75.0 60.3 56.2 640x480 75.0 72.8 66.7 59.9 720x400 70.1 DVI-0 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 477mm x 268mm 1920x1080 60.0*+ 60.0 1680x1050 59.9 1600x900 60.0 1280x1024 75.0 60.0 1280x960 60.0 1152x864 75.0 1280x720 60.0 1152x720 60.0 1024x768 75.0 60.0 832x624 74.6 800x600 75.0 60.3 640x480 75.0 59.9 720x400 70.1 Later edit: The problem seems to come from the ATI drivers.I managed to set up the monitors like I wanted after I uninstalled the drivers. Unfortunately I'm working on an OpenCL project so I had to reinstall them.The moment I did that, all my previous settings were forgotten and I was back to square one.

  Read the article

• Display stretches 4:3 ratios; Adds scrolling to other ratios

  - by Matt

  I have a dual monitor setup. Normally, they both display at 1680x1050. They have been setup this way for about a year. I'm using Windows XP Professional 2003 x64 SP2. Today, out of nowhere, one of the monitors kicked back to a lower resolution. I was not playing with any configuration at the time.. in fact all I had done was close a window (maybe a browser). But the thing is that the resolution is still preserved partially by the fact that the screen will scroll when you move the mouse. So it's like looking through a 1024x768 window into a 1680x1050 world. The monitor itself does not appear to be damaged, because I also have it connected to my netbook (via KVM) and higher resolutions work fine. I tried uninstalling/reinstalling the drivers to no avail. System restore doesn't help either. I'm unsure of the exact ATI card I'm using.. Device Manager lists it as "Radeon X300/X550/X1050". There is no Catalyst Control Center software installed. I tried to install it, but there doesn't seem to be a way to install it by itself ... it forces you to install another driver, which breaks both of my displays, forcing me to go into safe mode and run system restore again. Any ideas? Thanks EDIT: After playing around more, I discovered that the "scrolling" behavior is only present for aspect ratios that are not 4:3. For 4:3 ratios, it just stretches out to fit the wide screen. My monitor's native ratio is 16:9 .. what could be causing it to think it needs to scroll?

  Read the article

• can't access SATA card config screen on boot, nor access the disks

  - by Ronald

  We've just upgraded our file server using an ASUS P6T WS Pro board, running FreeBSD-RELEASE 8.2 and using zfs to manage 12 WD20EARS disks. Since our 3ware card has been giving us trouble we started using the six on-board SATA connectors and got a SuperMicro USAS2-L8i to provide eight more ports. Mechanically, the card is an awkward fit but electrically it all seems ok. Upon boot, the LSI controller shows up and states that pressing ctrl-c will bring up the LSI Config Utility. When doing that, the message changes to state that the utility will be started after initialization, however that never happens. There does seem to be an error message that's only displayed too briefly to read and seems to be about PCI and "not enough space". (That message is pushed off by a hardware summary and I've found no way to scroll back at this point.) The disks do not show up in any recognizable ways after booting, either. I found a hint in another discussion to check the address mapping on either the card or the motherboard BIOS, but have found no way to do that. So what I tried on a hunch is to disable everything that's on-board, including network adapters, Firewire controller and SATA. In fact, after doing that, I can successfully launch the LSI Config Utility. As far as I can tell, all looks well in there, and when booting in that configuration it also displays a list of the disks connected to it, which looks just fine as well. Only problem now is that I can't boot that way, because I need the on-board SATA controller and network adapters. As soon as I re-enable any of them I'm back to square one. That discussion I mentioned about mapping addresses said to try D000, then D7FF, then DFFF, in order. The LSI Config Utility shows the card address as D000 but offers no way of changing it. Any tips or insights would be appreciated.

  Read the article

• Solaris ldap Authentication

  - by Tman

  Iv been having a trouble trying to get my Solaris 10 server to authenticate against an eDir server.im managed to Set up my linux(RHeL,SLES) servers to authenticate against the ldap Server.which works fine. Here is my configuration Files. ldapclient list: NS_LDAP_FILE_VERSION= 2.0 NS_LDAP_BINDDN= cn=proxyuser,o=AEDev NS_LDAP_BINDPASSWD= {NS1}ecfa88f3a945c22222233 NS_LDAP_SERVERS= 192.168.0.19 NS_LDAP_SEARCH_BASEDN= ou=auth,o=AEDev NS_LDAP_AUTH= simple NS_LDAP_SEARCH_SCOPE= sub NS_LDAP_CACHETTL= 0 NS_LDAP_CREDENTIAL_LEVEL= anonymous NS_LDAP_SERVICE_SEARCH_DESC= group:ou=Groups,ou=auth,o=AEDev NS_LDAP_SERVICE_SEARCH_DESC= shadow:ou=users,ou=auth,o=AEDev?sub?objectClass=shadowAccount NS_LDAP_SERVICE_SEARCH_DESC= passwd:ou=auth,o=AEDev?sub?objectClass=posixAccount NS_LDAP_BIND_TIME= 10 NS_LDAP_SERVICE_AUTH_METHOD= pam_ldap:simple getent passwd works fine: root:x:0:0:Super-User:/:/sbin/sh daemon:x:1:1::/: bin:x:2:2::/usr/bin: sys:x:3:3::/: adm:x:4:4:Admin:/var/adm: lp:x:71:8:Line Printer Admin:/usr/spool/lp: uucp:x:5:5:uucp Admin:/usr/lib/uucp: nuucp:x:9:9:uucp Admin:/var/spool/uucppublic:/usr/lib/uucp/uucico smmsp:x:25:25:SendMail Message Submission Program:/: listen:x:37:4:Network Admin:/usr/net/nls: gdm:x:50:50:GDM Reserved UID:/: webservd:x:80:80:WebServer Reserved UID:/: postgres:x:90:90:PostgreSQL Reserved UID:/:/usr/bin/pfksh svctag:x:95:12:Service Tag UID:/: nobody:x:60001:60001:NFS Anonymous Access User:/: noaccess:x:60002:60002:No Access User:/: nobody4:x:65534:65534:SunOS 4.x NFS Anonymous Access User:/: tlla:x:2012:100::/home/tlla: test:x:2011:100::/home/test: thato:x:2010:100::/home/thato: pam.conf login auth sufficient pam_unix_auth.so.1 #server_policy login auth sufficient /usr/lib/security/pam_ldap.so.1 try_first_pass login auth required pam_dial_auth.so.1 rlogin auth sufficient pam_rhosts_auth.so.1 rlogin auth requisite pam_authtok_get.so.1 rlogin auth required pam_dhkeys.so.1 rlogin auth required pam_unix_cred.so.1 rlogin auth sufficient pam_unix_auth.so.1 rlogin auth sufficient /usr/lib/security/pam_ldap.so.1 try_first_pass rsh auth sufficient pam_rhosts_auth.so.1 rsh auth required pam_unix_cred.so.1 rsh auth sufficient pam_unix_auth.so.1 #server_policy rsh auth sufficient /usr/lib/security/pam_ldap.so.1 try_first_pass other auth requisite pam_authtok_get.so.1 other auth required pam_dhkeys.so.1 other auth required pam_unix_cred.so.1 other auth sufficient pam_unix_auth.so.1 other auth sufficient /usr/lib/security/pam_ldap.so.1 try_first_pass passwd auth required pam_passwd_auth.so.1 passwd auth sufficient pam_unix_auth.so.1 ssh account sufficient pam_unix.so.1 ssh account sufficient /usr/lib/security/pam_ldap.so.1 try_first_pass other account requisite pam_roles.so.1 other account sufficient pam_unix_account.so.1 other account sufficient /usr/lib/security/pam_ldap.so.1 try_first_pass other password required pam_dhkeys.so.1 other password requisite pam_authtok_get.so.1 other password requisite pam_authtok_check.so.1 other password required pam_authtok_store.so.1 other password sufficient pam_unix.so.1 other password sufficient /usr/lib/security/pam_ldap.so.1 try_first_pass Local Authentication Works But LDAP Authentication Doesn't Work.

  Read the article

• How can I explain to dspam that the user "brandon" is the same as "brandon@mydomain"

  - by Brandon Craig Rhodes

  I am using dspam for spam filtering by running the "dspamd" daemon under Ubuntu 9.10 and then setting up a Postfix rule that says: smtpd_recipient_restrictions = ... check_client_access pcre:/etc/postfix/dspam_everything ... where that PCRE map looks like this: /./ FILTER lmtp:[127.0.0.1]:11124 This works well, and means that all users on my system get all of their email, whether "dspam" thinks it is innocent or not, and have the option of filtering on its decisions or ignoring them. The problem comes when I want to train dspam using my email archives. After reading about the "dspam" command, I tried this on the files in my Inbox and spam boxes (which date from when I was using another filtering solution): for file in Mail/Inbox/*; do cat $file | dspam --class=innocent --source=corpus; done for file in Mail/spam/*; do cat $file | dspam --class=spam --source=corpus; done The symptom I noticed after doing all of this was that dspam was horrible at classifying spam — it couldn't find any! The problem, when I tracked it down, was that I was training the user "brandon" with the above commands, but the incoming email was instead compared against the username "brandon@mydomain", so it was running against a completely empty training database! So, what can I do to make the above commands actually train my fully-qualified email address rather than my bare username? I would like to avoid having to run "dspam" as root with a "--user" option. I would have expected that the "dspam" configuration files would have had an "append_domain" attribute or something with which to decorate local usernames with an appropriate email domain, but I can't find any such thing. When I used to use the Berkeley DB backend to "dspam", I solved this problem by creating a symlink from one of the databases to the other. :-) But that solution eventually died because the BDB backend is not thread-safe, so now I have moved to the PostgreSQL back-end and need a way to solve the problem there. And, no, the table where it keeps usernames has a UNIQUE constraint that prevents me from listing both usernames as mapping to the same ID. :-)

  Read the article

• Understanding what needs to be in place for a server to send outgoing email from a linux box

  - by Matt

  I am attempting to configure an openSuse 11.1 box to send outgoing email for a domain that the same server is hosting. I don't understand enough about smtp servers and the like to know what needs to be in place and working. The system already had Postfix installed, and I confirmed it was running via a > sudo /etc/init.d/postfix status I examined the Postfix config file in /etc/main.cf and configured a couple of items regarding the domain/host name and such, but left it largely default. I attempted to send an email from the command line with the following command: > echo "test 123" | mail -s "test subject" [email protected] Where differentdomain.com was not the same domain as the one best hosted on the server. However, the email never reaches the target account. Any suggestions? EDIT: In the postfix log, (/var/log/mail.info, there's nothing in .err) I see that postfix is trying to connect to what appears to be a different smtp server on our network, with a connection refused: connect to ourdomain.com.inbound15.mxlogic.net[our ip address]:25: Connection refused However, I can't figure out why it is 1) trying to connect to that server and 2) not just sending the messages itself... I mean, isn't postfix an smtp server? I did a grep -ri on ourdomain from /etc and see no configuration files anywhere telling it to do this. Why is it?

  Read the article

• Postfix aliases and duplicate e-mails, how to fix?

  - by macke

  I have aliases set up in postfix, such as the following: [email protected]: [email protected], [email protected] ... When an email is sent to [email protected], and any of the recipients in that alias is cc:ed which is quite common (ie: "Reply all"), the e-mail is delivered in duplicates. For instance, if an e-mail is sent to [email protected] and [email protected] is cc:ed, it'll get delivered twice. According to the Postfix FAQ, this is by design as Postfix sends e-mail in parallel without expanding the groups, which makes it faster than sendmail. Now that's all fine and dandy, but is it possible to configure Postfix to actually remove duplicate recipients before sending the e-mail? I've found a lot of posts from people all over the net that has the same problem, but I have yet to find an answer. If this is not possible to do in Postfix, is it possible to do it somewhere on the way? I've tried educating my users, but it's rather futile I'm afraid... I'm running postfix on Mac OS X Server 10.6, amavis is set as content_filter and dovecot is set as mailbox_command. I've tried setting up procmail as a content_filter for smtp delivery (as per the suggestion below), but I can't seem to get it right. For various reasons, I can't replace the standard OS X configuration, meaning postfix, amavis and dovecot stay put. I can however add to it if I wish.

  Read the article

• Nexus 1000v VEM fails on 2 out of 8 hosts.

  - by cougar694u

  I have 8 ESXi hosts. I do a fresh install from the installable CD directly to 4u1. We have another 2-node cluster with a working Nexus 1000v primary & secondary. Everything's up and running. I installed 6 hosts and everything worked great, migrated them to the Nexus DVS, and VUM installed the modules. I did the 7th host, and when I tried to migrate it to the DVS, it failed with the following error: Cannot complete a Distributed Virtual Switch operation for one or more host memebers. DVS Operation failed on host , error durring the configuration of the host: create dvswitch failed with the following error message: SysinfoException: Node (VSI_NODE_net_create) ; Status(bad0003)= Not found ; Message = Instance(0): Inpute(3) DvsPortset-0 256 cisco_nexus_1000v got (vim.fault.PlatformConfigFault) exception Then, I tried to do host 8, and got the exact same problem. It worked about 15 minutes prior when I did host 6, nothing changed, then went to host 7 and it failed. If I try to remediate either of these two hosts, either patches or extensions, it fails. Anyone else have these problems?

  Read the article

< Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >