Search Results

Search found 12795 results on 512 pages for 'video tutorials'.

Page 462/512 | < Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >

• Windows 7 boots to black screen with blinking cursor

  - by murgatroid99

  I have an Alienware M17x that dual boots into Ubuntu 11.04 and Windows 7 Home Premium. Currently, the computer starts at the GRUB loader and will boot into Ubuntu, but if I try to boot into Windows, I immediately get a black screen with a blinking cursor in the upper left corner. The output of fdisk -l is Device Boot Start End Blocks Id System /dev/dm-0p1 1 5 40131 de Dell Utility Partition 1 does not start on physical sector boundary. /dev/dm-0p2 6 1918 15360000 7 HPFS/NTFS Partition 2 does not start on physical sector boundary. /dev/dm-0p3 * 1918 64772 504878877+ 7 HPFS/NTFS Partition 3 does not start on physical sector boundary. /dev/dm-0p4 64772 77827 104858625 5 Extended Partition 4 does not start on physical sector boundary. /dev/dm-0p5 64772 67204 19531008 83 Linux /dev/dm-0p6 67204 74498 58593536 83 Linux /dev/dm-0p7 74498 77577 24731648 83 Linux /dev/dm-0p8 77578 77827 2000128 82 Linux swap / Solaris I have used the Windows rescue CD, and run the automatic error fixer until it finds no errors. I have run chkdsk /R on both the main Windows 7 (/dev/dm-0p3) partition and the recovery partition (/dev/dm-0p2). I set the main Windows 7 partition to be active. I also tried running in the recovery console the commands bootrec /fixmbr bootrec /fixboot bootrec /rebuildbcd None of these helped and the last set of commands deletes grub, which I then have to reinstall from Ubuntu. I think the last thing I did in windows before this started was install the newest ATI driver for my video card. This would suggest using system restore, and I actually had a restore point earlier (after the problem started), but after whatever I did that restore point does not appear in the list on the recovery disk any more, so I cannot do a system restore. Is there anything else I can try to make Windows boot properly again? Edit: Running the suggested commands bootsect /nt60 c: bcdboot c:\windows /s c: was also ineffective.

  Read the article

• picking a linux compatable motherboard

  - by Chris

  Last time I bought a new computer (I build them myself) I got a motherboard that had really poor linux support for a long time. Specifically the audio. I had to wait months before the kernel supported the on board audio chipset. That is exactly the situation I'm trying to avoid this time around. I have some specific questions about "server motherboards" actually. I looked at a few models of server motherboards by intel, and some random models on newegg. I wasn't able to see much of a difference from regular desktop motherboard other than most had two sockets, and support for much more ram. These boards seem more popular with Linux users. Why? AMD and Intel both have server CPUs as well. Some question, what's the difference? To make this question more concrete, I was looking at this this motherboard. The main questions about it that I can't answer are: Can I get a motherboard without on board raid and audio? I wanted to get a hardware raid controller and a PCI audio card. I thought a server motherboard would be cheaper and not have these "extras", since who wants an audio card on a server? Where can I found out about Linux support for the components on this board? "Intel ICH10R", "Realtek ALC889", "Marvell 88E8056" I'm buying this computer to work as a Linux desktop for a lot of compiling, coding and audio/video work, but I don't want to rule out the possibility of installing windows and playing some games at one point. (even if the last game I got has been sitting in its box unopened for almost a year). Is it a good idea to buy a "server motherboard" and play games on it, or are desktop boards better value for this? The ultimate solution for me would be a motherboard that had GPL divers for onboard LAN, a single CPU socket, lots of PCI express and PCI. USB 3.0, and no fancy hard disk controllers since I'll be getting a separate one.

  Read the article

• TCP Server Memory management: #Connections Vs. #Requests

  - by Andrew

  Given that, there is no theoretical limit to number of concurrent TCP connections a Windows 2008 server can handle. Only thing will happen is, with each connection there will be memory consumption in server. Unfortunately, memory is not unlimited (and I want to utilize only physical memory). For example, lets say we've 2GB server memory. Now there are two extreme cases: Case 1: If we've allocated 64KB buffer for each connection (only to receive incoming request), then 32768 connections can consume all the 2GB of memory. This will not leave any memory to queue/process incoming requests from those connections. Case 2: On the other hand, lets say a single (or very few) connections continuously keeps sending request buffers (for example, video streaming from one connection to other) and server cannot process them within time, those buffers will get piled up in server and eventually will occupy most of the servers memory. And it will not leave any memory for new connection thereafter. This is the real dilemma in server design bugging me badly for last many days. If I can decide on max size of request buffer per connection and max number of requests to allow in queue per connection. Then, based on available server memory, it will then automatically set limit on max number of concurrent connections. How to decide on these limits to achieve best performance and throughput? I am just looking for perfect utilization of server resources. Are there any standard guidelines or empirical data available with someone who can share with me please.

  Read the article

• Monitor goes black for a few seconds

  - by privatehuff

  I have a Hanns G 28" monitor, Model # HG281D It has its issues (viewing angle sucks) but has been functional and solid, great for desktop stuff. Worked without any sign of any problems for 6-12 months. However, now the monitor "goes black" for about 2-3 seconds, almost like when you click "detect display" It does not turn off (power light does not go amber) The computer is completely unaffected and the video mode never changes when the picture returns. The computer is fully responsive and will keep playing music or taking my keypresses during the time I can't see anything. (it just happened and I kept typing, etc) It happens on multiple computers across several operating systems. (I have an 8-port iogear KVM switch that has several computers connected) But, it seems to happen only on certain computers. I have a hackintosh that does it, a windows 7 PC that does not, a lenovo laptop that does not, and my old ubuntu 8.10 box did not do it, but my new mint 8 box does do it. I've check the connections and tried changing out the power cable and the vga cable. Sometimes it won't happen for hours (or days) and sometimes it happens several times per hour. It was happening many months ago, did not happen for months, and has now started happening again. Does this make any sense? What could it be?

  Read the article

• BSOD: PFN_LIST_CORRUPT and IRQ_NOT_LESS_OR_EQUAL

  - by David Lively

  I built a desktop about a year ago that has, until a few weeks ago, been running without a hitch using Windows 7 Ultimate. Recently, the PC started occasionally rebooting with a blue screen indicating a "PFN_LIST_CORRUPT" error. Also, I've seen at least once the error IRQ_NOT_LESS_OR_EQUAL. I seem to remember temporarily connecting an internal DVD burner about the same time this happened. I burned a DVD for another machine and promptly removed the drive. Yesterday, I reformatted the drive and installed Win7 Ultimate x64. During the first install, the PFN_LIST_CORRUPT bluescreen reared its ugly head again. A second install attempt completed with no errors. The fact that this error happened during a clean install leads me to believe that this is not a driver or OS issue. I also ran the memory diagnostic from the Win7 32-bit install DVD. It completed both passes with no errors. Periodically, the screen will flicker, as if explorer or the video are resetting. In the event log, I see a series of 8 or so errors indicating that some services unexpectedly stopped, and were apparently reset. These include an HID service and some others (I don't have a list in front of me). The PC is a Phenom X2 3 Ghz with a 500GB Seagate drive, 4GB of Corsair XMS2 cm2x2048-6400c5c. Anyone know what would suddenly cause a couple of sticks of RAM to go bad?

  Read the article

• come on!teach u save photos from iphone to computer

  - by goodm

  i am using iphone ,when we have fun,we took a lot of nice pics ,but,that is a question,how to transfer photos from iphone to computer,now ,let me show you,step by step: Step 1: Download Tansee iPhone Transfer Photo free trial version here,and then install it. You also need iTunes above 7.3 installed.or download at: http://www.softseeking.com/prodail.aspx?proid=74 Step 2: Connect iPhone to your computer. Step 3: Launch Tansee iPhone Transfer Photo and all the photos in your iPhone will display automatically, Step 4: Select the photos to be transferred to your computer, the selected file will marked with red border. You can select photos by click on each one, or just drag a rectangle to select a bundle of photos. You can also select all photos by click right button of your mouse or click "File" to choose. Note: you can only select first 6 photos if you haven't purchase. Step 5: Click "Copy" button to select output path and start to transfer photos to your computer: iPhone Camera Photo & Camera Video: Click "Camera Roll", do as steps above can copy your iPhone Camera Photos and iPhone Camera Videos to PC. Options Setting 1.Backup File Format: To select backup photo file format, Tansee iPhone Transfer Photo support BMP and JPG file now. 2.Backup Path: To select directory for storing the backup photos. You can select backup directory for each photo during backup by check "Ask Every Time" or store all files in a specified directory by checking "Save Here" and select the directory in the edit box. 3.Backup Resolution: To select the photo size to be backup.

  Read the article

• Add single sign-on into existing web app

  - by EvilDr

  Apologies if this isn't the best site, I've search for an answer but can't find anything quite right. I don't actually now the correct terminology I should be using here, so any pointers will be appreciated. I have a web application that accessed by many different users across different organisations. Access is provided by each user having a unique username/password which is stored in SQL (database fields are customerID, userID, username). Some organisations are now asking if we can change this to allow "Active Directory single sign-on" so that users don't need to remember yet another set of login details. From research I can see how this is achieved using OpenAuth and Google (etc), but I know hardly anything about AD and can't find much information on this (again I'm sure it helps when you know the terminology). Is this request even possible to achieve, given that most users will be from different (and unrelated) organisations? I saw on a Microsoft Build video not long ago that there is some kind of replication service for AD to allow Cloud authentication. Is this what I should be aiming for?

  Read the article

• Is VGA port hot-pluggable?

  - by Martin Bøgelund

  In meetings, I often see people detaching the VGA connector from one running laptop and connecting it to another, while the projector is still on. Is this 100% risk free, and OK by design of the VGA standard? If there's a risk involved in hot-plugging VGA, can it be removed by turning off or suspending either laptop, display, or both? I see this being done all the time without causing disaster, so clearly I'm not interested in answers stating "we do it all the time, so it should be OK!". I want to know if there's a risk - real or in theory - that something breaks when doing this. EDIT: I did an internet search on the topic, and I never found a clear statement as to why it is safe or unsafe to hot swap VGA devices. The typical form is a forum question asking basically the same question as I did, and the following types of statements Yes it's hot swappable! I do it all the time! It involves some kind of risk, so don't do it! You're some kind of moron if you think there's a risk, so just do it! But no explanation as to why it safe or not... Joe Taylors answer below contains a link to a forum post and answers that basically give me the same statements as mentioned above. But again, no good explanation why. So I looked for an actual manual for a projector, and found "Lenovo C500 Projector User’s Guide". It states on page 3-1: Connecting devices Computers and video devices can be connected to the projector at the same time. Check the user’s manual of the connecting device to confirm that it has the appropriate output connector. [image] Attention: As a safety precaution, disconnect all power to the projector and devices before making connections. But again, no good explanation.

  Read the article

• Hosting a server for websites, ftp and random use at home?

  - by Zolomon

  I'm wondering what's the best option for me if I want to move all my hosted websites (from a hosting company) to a server at my own home? Basically, the needs I have are: be able to host websites using PHP/ASP.NET (haven't really decided yet - both would be preferred!) enable FTP so I can create accounts for my family members to access the server for file handling SSH SSL - for secure connections (this is something you have to buy/apply for per domain, not sure if there are any server side settings that have to be made) be able to stream video remote desktop host home-brew applications that can run as services use either MySQl/SQLite/SQL for relational database storage What should I think of before I buy a server? What hardware will I need, what will limit my server? I basically want to learn networking better as I'm a software and web developer but haven't had the resources to acquire any serious toys until now. At the time of writing, most of my websites have 60 visits/day so I don't suspect them to be very demanding. Is there something I haven't thought of that I should have? What OS would you suggest I run? FreeBSD vs Windows Server vs ?

  Read the article

• Windows 7 Won't Boot

  - by Vie

  I recently built a new computer, my fifth one. ASUS Maximus III Formula LGA 1156 Intel P55 ATX Motherboard EVGA 01G-P3-1452-TR GeForce GTS 450 Superclocked 1GB 128-bit GDDR5 PCI Express 2.0 x16 HDCP Video Card COOLMAX RM-1000B 1000W ATX psu Intel Core i7-875K lynnfield 2.93GHz LGA 1156 95w Quad-Core unlocked processor G.SKILL Ripjaws Series 16 (4x4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10666) memory WD VelociRaptor WD3000GLFS 300gb 10000 RPM SATA 3.0Gb/s Hard Drive Sony Optiarc CD/DVD Burner model AD-7261S-0B LightScribe Windows 7 Home Premium 64-bit It gets hung up on the starting windows screen. When I went to install the OS it did the same thing wouldn't go past the windows logo, so I put the new HDD into my old computer and installed windows 7 thinking it was just an installer error. Put the fully installed HDD back into my new machine and it still gets stuck on the starting windows screen. I've tried most everything I've looked up. Disabled USB, Disabled Turbo Boost, Disabled everything that wasn't essential(just about every configuration I can think of), took it apart and put it back together, took all the ram out save one 4g stick(wouldn't even boot when I did this), did a memory scan which came back successful, I don't know what could be wrong. Only thing I can think of is a compatibility issue somewhere, but I've ran over it again and again and I don't know where there would be an issue like that. Need Backup! .<

  Read the article

• Firefox cannot render icons from Font Awesome webfont set

  - by ADTC

  In Firefox (Windows 7), icons and glyphs that are called from the Font Awesome package do not render properly. An example of this can be seen on the Khan Academy website. Below the video the icons are shown as boxes with hex codes in them. This means that it isn't getting downloaded by Firefox. How it appears on Chrome (Windows 7), Safari (Mac OS X) and Stainless (Mac OS X): I found this question on Stack Overflow that may explain why this happens -- the CSS does use single quotes to enclose the font's src location. However, I don't have any write access to Khan Academy servers so I can't modify the actual website. I want to know if this can be fixed in Firefox, and how. I can run Greasemonkey scripts if that would help. I've already tried manually downloading the font and adding it to Windows' Fonts folder but this does not help. For reference, the CSS that sets this font up (not processed properly by Firefox) is: @font-face { font-family:'FontAwesome'; src:url('./fontawesome-webfont.eot'); src:url('./fontawesome-webfont.eot?#iefix') format('embedded-opentype'), url('./fontawesome-webfont.woff') format('woff'), url('./fontawesome-webfont.ttf') format('truetype'), url('./fontawesome-webfont.svg#FontAwesome') format('svg'); font-weight:normal; font-style:normal } [class^="icon-"]:before, [class*=" icon-"]:before { font-family:FontAwesome; font-weight:normal; font-style:normal; display:inline-block; text-decoration:inherit }

  Read the article

• How does Tunlr work?

  - by gravyface

  For those of you not in the US, Tunlr uses DNS witchcraft to allow you to access US-only (and UK-only stuff like BBC radio online) services and Websites like Hulu.com, etc. without using traditional methods like a VPN or Web proxy. From their FAQ: Tunlr does not provide a virtual private network (VPN). Tunlr is a DNS (domain name system) unblocking service. We’re using sophisticated technologies (a.k.a. the Tunlr Secret Sauce ©) to re-adress certain data envelopes, tricking the receiver into thinking the envelope originated from within the U.S. For these data envelopes, Tunlr is transparently creating a network tunnel from your location to our U.S.-based servers. Any data that’s not directly related to the video or music content providers which Tunlr supports is not only left untouched, it’s also not even routed through Tunlr. In order to use Tunlr, you will have to change the DNS address. See Get started for more information. I can't really wrap my head around how this works; I have always assumed that these services performed a geolocation lookup via your client IP. Just really curious as to how this works. EDIT 2 I believe they're only proxying the initial geo check and then modifying the data stream request to include your real IP address so that the streaming is direct, not proxied.

  Read the article

• using a second computer as a mere screen/monitor in X (VNC?)

  - by lara michaels

  Hello My goal is to use three monitors with my Linux system. It is a laptop, so adding another video card is not the easiest solution. (I have investigated a number of such options: getting a docking station with a PCI slot, USB/Cardbus vga adapters, etc, and for the time being don't want to go that way.) I am wondering if using an older desktop+screen I have lying around as the third "monitor" might be the easiest solution, if only there is a way to get it to work as a seamless, integrated desktop. I was wondering if I can use VNC or perhaps X itself (?) to achieve the following: computer A is my main computer; it has all my files, etc. computer B is used just to display on an additional screen keyboard+mouse are connected to computer A use VNC or X to connect the two so that computer B shows a X screen that is just as if it was a third physical screen connected to computer A. I don't know if the last point is clear, but what I mean is that I would like to be able to: be able to have my window manager assign/move around virtual desktops on all three screens move windows back and forth between the screens attached to computer A and the screen of computer B be able to copy something in an app being shown on a screen of computer A and paste it into an app being shown on the screen attached to computer B access the filesystem on my main computer (A) when using applications that are being shown on the screen attached to computer B Basically, I would like X to treat computer B just like it was nothing but a third physical screen... Is this doable? : ) ~lara

  Read the article

• Computer does not boot after ram upgrade

  - by Calmarius

  I have a Dell Optiplex GX520 desktop (it's abount 5 yr old) PC with 512 MB DDR2 RAM. Since my computer always swapping I thought I should upgrade my RAM. I bought a Kingmax 2GB DDR2 RAM. But my system does not boot. The status leds are on 2 and 4. The user manual says 'video card failure' wtf? I put back the original module and everything works. I tried many combinations. When I leave the old 512 RAM in and put the 2GB next to it to the other socket my system completes the POST and I'm able to enter the BIOS menu. It says my system has 2.5 GB installed, one 0.5GB and one 2GB in dual asymmetric channel mode. It's seemingly right. Exiting the BIOS setup GRUB loads successfully, but when I try to boot Ubuntu it crashes with kernel panic immediately. Trying to load Windows XP does not get past the loading screen, it crashes with 0x8E stop error. Does this mean the ram I bought is faulty? Or is it just mean that the memory module I bought is too new to be handled my computer? I this case I may exchange the RAM with my friends. No other computer is in my house (my very old box has DDR1 ram, my systers new box has DDR3 ones. I can't plug my memory in neither one.) I'm going to return the RAM to store to replace it with a better one tomorrow. Is there any hope to get this new module work?

  Read the article

• Home Server: storage virtualisation, what to choose?

  - by Huygens

  I'm looking for virtualisation solutions for storage and OS for a home server. A sort of private cloud where I manage the storage space independently of the VM one. This question focus on storage management. (I have another question related to the VM/compute instance management). Here my environement and wishes. Server: HP Proliant MicroServer with 8 GB RAM (AMD Turion dual core with AMD-V technology) with 1 250GB system disk and up to 4 HDD (2 TB) for "data" OS types: only Linux (perhaps a *BSD VM in the future) Linux distributions do not matter, I'm familiar with RHEL, Fedora, Suse, Ubuntu, but any other recommandation will be fine The 4 HDD is going to be a software RAID array, probably RAID 5. storage should be "virtualised/cloudified": easy to extend: if I add a NAS on the network, I can include the NAS space capacity within this storage space as one virtual disk. This can be a NAS, an external HDD or another server. cluster FS or S3 style space or OpenStack block storage? Whatever is easier to manage/maintain and easy to integrate/plug to VM/compute instance. I would prefer free (libre, as in a free speach) and open source tools. But it does not have to be free as in a free beer. Note: the VMs I intend to run on top of this server are one dedicated to backup, one for a "owncloud/dropbox"-like service and perhaps one for media server (hosting video and photos). I'm not sure if traditional VMs or compute instance are the most suitable for this.

  Read the article

• How to serve media across home network?

  - by TK Kocheran

  I'm looking to share my media across my home network. Router fully supports running a DLNA server, but I don't know if it'd be better to run the server from my main server computer instead of from the router, as the router would have to operate off of a network share and my server can operate directly off of the files. Here's what I need to serve, in order of importance: ISO 1:1 DVD rips (4-8GB files), MP4/H.264 encoded videos, MKV videos, MP3 files, JPEG/CR2 images. Maybe I'm completely ludicrous for wanting to push full DVD files across my network, but in reality, I would assume that only the parts of the actual file needed (ie: menu, main video payload for main title) would be served at any one time. Plus, encoding takes time and precious disk space, so why not stream it 1:1 ;) Does anyone know of the best way to accomplish this? Main goal is to serve it to Logitech Revue downstairs and secondary goal is to serve it to other computers in the house. For music, I assume I could run a DAAP server, but I don't think that the Revue supports that (and I can't exactly throw together an app that does it just yet).

  Read the article

• Is it possible for a faulty processor to cause audio static/noise?

  - by Tom

  I have a Core 2 Extreme processor I received from a friend and have set up an XBMC box using it. However, I constantly get audio static whenever playing any music or videos. Here is a video of the sound: http://www.youtube.com/watch?v=SqKQkxYRVA4 I have tried replacing everything short of the case and the processor, including cables, audio interfaces, operating systems, ram, etc, leading me to think it might be either the case shorting out the motherboards I have tried or a faulty processor. Is it possible for a faulty processor to cause audio static/noise? Any feedback would be appreciated. Edit - Here's a list of things I have tried: Reinstalling OS Installing/upgrading/repairing PulseAudio/Alsa Installing alternate OSes, straight Ubuntu, Lubuntu, Xubuntu, Arch, Mint, Windows 7 Switching audio from the external card to internal Optical, audio out through HDMI, audio out through headphones Different ports on receiver (my main desktop sounds fine on the same sound system) Different optical cables Unplugging everything unnecessary from the motherboard (1 HD, 1 Stick of Ram, 1 Keyboard) Swapping out ram Swapping out the motherboard Replacing the Graphics Card (was replaced due to fan being noisy, not specifically for this problem) Different harddrives Swapping power supply Disabling onboard audio Switching Power Cable Plugging in through surge protector Plugging into different outlet on separate circuit

  Read the article

• How can I wipe my iPod classic and fix any bad sectors on the hard drive without killing it?

  - by Sam Meldrum

  My iPod never finishes syncing and only syncs audio, not pictures or video. Any ideas as to how I can fix it? My iPod classic 160GB worked well for a couple of years. I used to sync a lot of photos at full resolution to it, but this recently stopped working after I moved to Windows 7. iTunes is on latest version - 9.1.1.12 iPod software is up to date - 1.1.2 Windows 7 is fully up to date and patched The symptoms are that the iPod will start to sync, all audio (music and podcasts will sync successfully) but the syncing will then just appear to continue - itunes message: Syncing iPod. Do not Disconnect. This sync never completes - I have left it trying for days. I have tried resetting the iPod using the Restore button, whereupon it restarts sync from default options and again will sync audio, but nothing else. I suspect that something has gone wrong on the hard-drive - either a bad sector or some corrupt data. Is there a process I can go through to fix this? E.g. SpinRite or a format? If so how do I go about formatting an iPod and will it be recognised as an iPod after format and work as normal? Any advice on what to try next much appreciated? Update I have eliminated problems with the files, PC or iTunes as they sync fine to other iPods. I have also eliminated the cable by trying different cables which work with other iPods. What I'd really like to know is if there is any way to more fundamentally wipe the iPod safely, attempt to repair any bad sectors on the hard drive and then start from scratch. Anyone ever managed this?

  Read the article

• Very high-pitched noise when computer does something intense?

  - by Starkers

  "Intense" is the best word I can use to describe it because I'm not sure what it is, whether it's RAM, GPU or CPU. If I pan the camera in unity: A high pitched noise issues from the computer. The picosecond I start panning the sound starts. Stops the picosecond I stop panning. If I start an infinite loop: 2.0.0p247 :016 > x = 1 => 1 2.0.0p247 :017 > while x < 2 do 2.0.0p247 :018 > puts 'huzzah!' 2.0.0p247 :019?> end huzzah! huzzah! huzzah! An identical high pitched noise can be heard. I don't think it's the GPU due to this simple experiment. Or any monitor-weirdness (although the sound does sound like one of those old CRT monitors if you're old enough to be young when those things were about) The CPU? Or maybe my SSD? It's my first SSD and the first time I've heard this noise. Should I be worried? Regardless, what's causing this sound? I can't think what would cause such high frequency vibrations. I built the PC myself. Not enough heat paste on the CPU? Too much? Just no idea what's going on. Info: CPU Type QuadCore Intel Core i5-3570K, 3800 MHz (38 x 100) Motherboard Name Asus Maximus V Extreme Flash Memory Type Samsung 21nm TLC NAND Video Adapter Asus HD7770

  Read the article

• Sudden and frequent hangs on desktop computer: mobo or CPU fault?

  - by djechelon

  I have a desktop computer equipped with an ASUS Crosshair 2 Formula and a Phenom x6 3.2GHz CPU. My problem is that often the computer will hang all of a sudden, completely stopping responding. When that occurs, reset key is inoperative and power button turns the computer off but is unable to turn it back on. I have to physically disconnect power cable. The problem can occur anytime, when I'm booting Windows, when I'm logging in, when I'm listening to a song, when I'm browsing Internet, etc. It always occurs after very few minutes of 3D gameplay I thought it was a video card fault. I had 3 8800GTX so I could try all combinations of them: didn't fix I thought it was a RAM problem: I tried running with only a subset of my DDR2 banks but didn't fix. Almost every time I have to reset and reconfigure BIOS (without AHCI, Win7 won't boot, so I need to restore a few things). If I enable AMD Live, Cool&Quiet or other things from CPU configuration menu I'll be sure that the computer won't reach Windows desktop in 99% of cases (it randomly hangs somewhere in the boot process or even in the BIOS POST). Another interesting thing is that during the POST process the computer always takes unusually long time detecting USB devices (LCD POSTer shows USB INIT), and I've also tried disconnecting all USB devices but didn't take less time to POST BIOS revision is 2702, the latest. Today I found a different behaviour once: during boot screen I got a BSOD with error Stop 0x00000101 A clock interrupt was not received on a secondary processor within the allocated time interval, and this is usually related to overclocking, but I never overclocked my CPU. Judging from the description of my problem, hoping someone had the same and fixed, and since I don't have a spare CPU or motherboard for replacement, I'd like to ask if you think this is a problem with faulty CPU or faulty motherboard, and if I can perform additional tests (I mean software tests because of my lack of spare components) to identify the component to replace.

  Read the article

• Linux Mint Constantly freezing on Dell XPS L502X

  - by Josh

  I recently partitioned my hard drive to dual boot the existing Windows 7 with Linux Mint because I am tired of using Windows, especially the lack of terminal. I want to eventually remove Windows 7 and just run it from a VM within Linux Mint, but I want to make sure that I like the Mint before going all in. I ran Linux Mint on a VM inside Windows for a while, enjoyed it, and never had any issues with it. Since installing on my hard drive it has started freezing every 5-10 minutes, and the only way to get it back is to either power down, or close the lid and reopen once it sleeps. I've also tried running Ubuntu on dual boot in the past, and while it never froze, the battery life was terrible, and the fan was constantly running. I'm experiencing the same battery/fan problem with Mint, which doesn't make sense to me, as Linux should be lighter on the CPU than windows. If I had to guess I'd say it's probably a driver thing, with my video card or fan or something. My battery life in Windows is ~2 hours and its about 40 minutes in Linux. At this point, that is even if my laptop doesn't freeze before then. On a less important note, I also have an intel Centrino 6150 WiMax card that I'd like to be able to use, but that won't register on the Linux system either. I have tried downloading drivers for both of these, but neither have solved my problems. I'm definitely getting frustrated and am getting close to giving up on Linux even though I dread working on a Windows machine.

  Read the article

• Flickering dual screens in Virtual Box Ubuntu 13.10 Guest

  - by alexleonard

  I have Ubuntu 13.10 x64 installed as a guest in VirtualBox (under a Windows 8.1 host) and have the settings for the virtual machine setup to run with a monitor count of 2, 128MB video memory and 3D acceleration enabled. In my guest I have the virtual box additions installed (which allowed me to have two 1920x1080 screens). Here's a screenshot of my VM settings. My laptop is an Asus N550JV which has both Intel's HD Graphics 4600 GPU and Nvidia's GeForce GT 750M. By default though I believe the Intel GFX card is being used to render the VM. When I boot up the VM it loads perfectly on dual screens, however whenever I move the mouse from one screen to the other (I have a Dell S2340L running over a HDMI connection as a second screen) the screen flickers. I've tried a variety of settings changes in both Ubuntu and the VM settings, but cannot seem to stop this screen flicker. I also used the NVidia control panel in Windows to force the dedicated graphics card to always be used but found that the display driver sometimes crashed whilst working in the VM, resulting in my VM session being destroyed, so I figured it's better to stick with the Intel GFX as that appears to be more stable. I also tried without 3D acceleration but that was much worse, and if I ran the VM with a low amount of graphics memory it really struggled. Here's my dmesg output: http://pastebin.com/1LJuYWMj (not sure if this is helpful in this situation). I read some posts suggesting changes to /etc/X11/xorg.conf but I don't appear to have an xorg.conf file. There were also a few posts (though related to Synergy) suggesting running xset -dpms but this command doesn't appear to have had any effect for me. As an additional note, I'm finding that window drawing in the guest is a little laggy/glitchy. For example, quickly scrolling through a web page may result in parts of the viewport displaying original content. Certainly I notice drawing issues most in the web browser, but it also impacts other software with parts of the window not being drawn when, say, switching between accounts in thunderbird. Any suggestions greatly appreciated!

  Read the article

• httpd.config Easy Apache WHM CentOS

  - by jessie

  First let me explain how I got to this situation. I run a Streaming Video Site. Videos are about 100-250MB in size at any given time there are 500 people on the site. So I guess that would make then static. Recently My site started getting really slow and the only way to fix it temporarily was to restart apache. Now there was no change in traffic that could have caused this. My site is not being attacked. My hosting company recomended to implement mpm_mod and suPHP. They did that by using Easy Apache in WHMS. Then everything was working fine but a little slow. I researched around and to my understanding that mpm will do that but be more table. I was told that installing FastCGI would speed things up just enough. Well that made everything worse. The site is slow and time's out. I used WHM and took off fastCGI but its still the same, it seems like everything i do as of now nothing changes. I even did a roll back on the htconfig file but that didn't work. I'm not sure how to fix this. and my hosting network guy wont be able to touch the problem until Tuesday. I have root access.

  Read the article

• Proxychains, Tortunnel, Privoxy: cannot connect() to port

  - by Benjamin

  Hi all, I'm trying to do an nmap scan through tor using tortunnel, privoxy and proxychains like explained in the following video: http://vimeo.com/6238958 I'm getting rather weird results. I can successfully perform any SYN scan on any port. However as soon as I try to do connect() scans, proxychains cannot connect itself to all ports. In other words, I can perform connect() scans to port 80: proxychains nmap -P0 -A -sV www.zzz.com -p80 but not port 21: proxychains nmap -P0 -A -sV www.zzz.net -p21 I get the following error: Starting Nmap 4.62 ( http://nmap.org ) at 2010-06-02 08:34 UTC ProxyChains-2.1 (http://proxychains.sf.net) random chain (1):....127.0.0.1:5060....can't connect to..113.I2.1W1.YY:21 random chain (1):....127.0.0.1:5060....can't connect to..113.I2.1W1.YY:21 random chain (1):....127.0.0.1:5060....can't connect to..113.I2.1W1.YY:21 random chain (1):....127.0.0.1:5060....can't connect to..113.I2.1W1.YY:21 random chain (1):....127.0.0.1:5060....can't connect to..113.I2.1W1.YY:21 random chain (1):....127.0.0.1:5060....can't connect to..113.I2.1W1.YY:21 My only guess would be that the exit node I'm using does not allow connections to port 21. Would that be correct? How could I fix it? Thanks for your time.

  Read the article

• Connecting a laptop to a TV via HDMI

  - by Madmartigan

  I just bought a new Dell XPS17 laptop (Win7) that only has HDMI output. My last 2 laptops had VGA, which I used to connect to my Sony Bravia 32" TV with no issues, but with the HDMI it's been quite a headache. Drivers for display adapters have been updated to the latest versions: Intel(R) HD Graphics Family NVIDIA GeForce GT 550M I went to a store and plugged in to 4 different TVs from different manufacturers. A sales rep and I spent about 30 minutes being baffled by the results (which are the same as my current TV): Extreme buggy behavior in the Nvidia and Windows display/resolution control panel Can not extend or duplicate displays, can only select one Third and fourth output devices "randomly" detected by the Windows control panel Could not get the screen to fit the output (edges cut off on all sides by about a half inch) Resolution and colors less than perfect. Artifacts around text. Display "randomly" cuts out Defaults to TV output only when plugged in Can not change resolution on either device when connected No audio from the TV Plugged in to 3 monitors from different manufacturers: Defaults to duplicated displays when plugged in Everything works perfectly So far, four people have gone through all the settings in the latop with no luck. I had similar, but not exactly matching results with a different laptop. I'm using the Sony Bravia currently at home, but in order to get it to work I have to turn on the laptop, wait until the display shows up on it, close the lid, then cycle through each output channel on the TV until I come back around to the HDMI port again, but still I have the symptoms described above. However: Once in a while, it just works. Sometimes, seemingly randomly, the output fits the screen perfectly. Sometimes the audio comes through the speakers too, but not always. Usually my screen saver "Mystify" will come up with a message that it cannot be displayed due to a limitation of the video card, but then sometimes it works fine. These 3 things seem to be independent of each other and don't always happen together. So, is there any way to get the laptop to output correctly to a TV, or is it just not meant to be?

  Read the article

< Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >