Search Results

Search found 20799 results on 832 pages for 'long integer'.

Page 466/832 | < Previous Page | 462 463 464 465 466 467 468 469 470 471 472 473  | Next Page >

• PackageForTheWeb "should not be executed directly"

  - by Sergei Ousynin

  When trying to install package (specifically, chipset drivers for Nexcom PEAK-series computer, but I guess it doesn't really matters) I get "PackageForTheWeb Error" saing "This program is used internally by PackageFromTheWeb. It should not be executed directly." I get this error on both Windows 2000 (where it should be installed) and Windows 7. The original driver CD was lost long time ago, so the package was downloaded from the Nexcom website, found no info about installer prerequisites there. What should I install (or anything else) to install this package? UPD: I found a solution - unpacked the package and executed setup.exe that was inside. But I'm pretty sure it's not an action supposed by vendor, so answers are still welcome.

  Read the article

• Tell the linux kernel to put a file in the disk cache?

  - by Rory

  Is there any command to for a file to be read in and loaded into the linux disk cache? This is on an up-to-date debian system. I know in the general case, it's better to let the linux kernel figure this out. But I have an edge case. I have a laptop that has an NFS director mounted, and i want to play a long video file, but I don't want to have a network problem interrupt the playnig. I know that (largeish) file will be read in it's entirety later on. I know that nothing else (really) will be running while playing this video. There is enough free memory to store this file. (I know I could just copy the file into a new tmpfs filesystem, but I'm curious if there's an even shorter way to do it)

  Read the article

• How to write to a file and, while the file is still being writen, read and parse its contents using

  - by Isabelle

  Hello. I'm actually trying to write a shell script that logs the output of a command to a file but, since the command takes a long time to complete (about 15 minutes), I would like to start parsing the output of the command (content of the file) before the command is completed, so I can send messages to the standard output (the user), like: 10% complete 45% complete and so on. Program steps Redirect command to a file: $(command) $FILE Start reading and parsing the output ($FILE) before the command is finished. I thought of using pararell programming, but I havent't got the hang of it. Any help you be appreciated. Best regards.

  Read the article

• Failed 11.10 to 12.04 upgrade and drove me crazy!

  - by Ivan

  Please help me with this! I first tried to upgrade my Ubuntu server from 11.10 to 12.04 thru Upgrade Manager, but never succeeded! Then I tried upgrading thru terminal, which took me ~4 hours as I was warned. When I restarted my computer, my login GUI did not show up at all! (Panic I was!) But when I switched to tty6 and it seemed the upgrade has finished, at least partially and got message Ubuntu 12.04LTS and telling me 12.10 is available. There are bunch of unmet dependencies...."apt-get install -f" may resolve the problem. Then I tried: sudo apt-get -f install, did not succeed! Also I tried sudo apt-get update && sudo apt-get upgrade I got bunch of error message too long to list here. Then I tried: sudo do-release-upgrade still bunch of error message there! There seems a lot trouble with the upgrade from 11.10 to 12.04 for me. Did I miss anything? Anyway, can I ask how I can get the gnome login GUI back? Thanks a lot! Yifang

  Read the article

• How to start a Software Company

  - by MeshMan

  I've always been interested in wondering how software companies happen. I find it extremely difficult once you're tied down with car, house, life etc. Funding is always the biggest concern. To make this a bit more specific, I see two types. Those offering a product/service or those offering a consultancy company. One things that bugs me about the product/service kind is that we all know how burning the candle at both ends is extremely exhausting. Coding for 8-10 hours in the day and then code in the evenings on your own stuff, doesn't last long. No matter how passionate you are about your idea, simply put, coding day and night is a recipe for burn out. Is this a defeatist attitude though? Can it be balanced? A consultancy kind isn't as tricky in my honest opinion. I think once you have spent years and years in the industry building up relationships, contacts from contracting or moving around, and of course, being involved in the community, then landing your first project as a consultant I'm sure is easier than the product/service kind. I'd imagine friends then could join you as you take on bigger company projects, like an Agile implementation or TDD training, then off you go gaining bigger things. Could you please specify which company type you're answering if you can't contribute to both. I'd like to hear everyone's experiences or ideas on any level for software company start-ups.

  Read the article

• Why does MOVE command in DOS treat wildcard patterns oddly in this case?

  - by Adisak

  I am using the "move" command with a wildcard pattern in the CMD prompt under Windows 7. In my source directory, I have the following files: movie1.avi movie1.avi_metadata movie2.avi movie2.avi_metadata If I type the command move source\*.avi dest it will move all four files even though I would expect it to only move the two *.avi files and not the *.avi_metadata files. As expected, move source\*.a dest and move source\*.av dest don't move any files. However when the length of the extension for the wildcard pattern is 3 characters, it will move all extensions that begin with those first three characters. Is this a bug in the "move" command or expected behavior and is it documented anywhere? Edit: John Watts notes that this is probably do to "short" filenames. Is it possible then to make commands in the CMD interpreter only operate on long filenames and to ignore short filenames?

  Read the article

• Inverting colors of a PDF

  - by legr3c

  I need to invert all the colors of a PDF document (background, text, graphics, and images). I want it persistent in the file so the inverted viewing options, that some viewers offer, won't help. Rasterizing the document and using image manipulation software is also not an option. I read somewhere that this can be done with the Enfocus PitStop plugin for Acrobat. However I didn't see a corresponding command anywhere. Am I missing something? Then I read that the ARTS PDF Crackerjack plugin for Acrobat offers negative printing so I tried that, too. The option is there but it simply doesn't work. I have been searching for very long for a way to do this. It seems like a common enough task but I just can't find out how to do it. Are there maybe any virtual printer drivers or something of the sort that support negative printing? Can anyone help?

  Read the article

• Ubuntu 12.04 Fails to Boot after Reboot

  - by Joe

  I have installed Ubuntu 12.04 on several Dell c6220 servers. The install was successful and all hardware is recognized. The problem that I am running into is that when issuing the reboot command or when pressing ctrl-alt-del, the server shuts down, but never comes back up. Instead, the fan revs up to full speed and stays that way until I power the server down. Once the server has been powered down via the power button, Ubuntu will boot just fine -- until the next reboot. I have found that by rebooting the server via the DRAC web interface will reboot the server correctly. I have also found that this problem does not exist with CentOS -- I can press ctrl-alt-del all day long and it always comes back up. I've tried several kernel parameters such as: reboot=bios reboot=pci reboot=acpi reboot=cold acpi=off noapic Nothing seems to work. I have also tried upgrading to kernel 3.4, but no change there, either. Has anyone run into a similar problem or any pointers on troubleshooting? Thanks, Joe

  Read the article

• Ubuntu 11.10 w/ Cinnamon - Icons are gone and pictures do not display

  - by B U N N Y

  I'm new on this site and new to using Ubuntu and all. I currently have Ubuntu 11.10 and Cinnamon along with it. I've recently downloaded only a few applications, like the Adobe shockwave as well as a few games. After the downloads, the icons for the windows (the close, minimize, and maximize) are nothing but streaks of colours, and now just plain black, picture previews in my picture folder is gone, some icons on the panels are missing, and icons in the control center are gone. I'm sure more are gone, but that's the ones that I see often. I'm not sure what caused this to happen?? Please get back to me soon! I'm worried about what has happened. ): This is my only laptop to get online. I have no other way besides the library but that takes too long.. EDIT: Okay, I had asked my sister for some help and she helped me restore my minimize, maximize, and close button but I still haven't figured out how to show the icons in the cinnamon dock (which I have set at the top of the window) and how to have my pictures show up again. All of my pictures are just blank and I can't even preview them. They still have their file names but that is it. I'm not sure what has happened. I haven't downloaded any new apps as of the new edit.

  Read the article

• Old Fglrx Driver - AMD Radeon HD 3200 - ubuntu won't start

  - by Yohannes

  I've been using Ubuntu 12.04 64 bit for about 2 weeks now and I installed the latest Fglrx driver (Graphics Card- AMD HD 3200, PC- Acer Aspire 5336, 4GB RAM, 500GB Harddrive). The problem is that sometimes video's lag and play out of sync sometimes the windows take long to show up after I've clicked them etc. After looking around I found a video on Youtube by Ubuntu help guy and in the video he recommended using an older driver if you have an older graphics card, his was about 4 years old (same as mine) and he used the 11.10 catalyst driver so I decided to try it. I removed the previous installation of the driver and then installed the 11.10 driver. However, when I restarted it instead of going to the GUI it goes to a terminal like window and asks for my login. Now its pretty clear I need to remove the old driver and go back to using the latest one. The only problem is I'm not sure where I saved the latest driver and in order to connect to the Internet I need to change /etc/resolv.conf (I use a static IP). So what should I do? Also anyone from personal experience, what propitiatory driver works best with my graphics card? As in the version. Thanks

  Read the article

• Is there a product planning tool that has these specific features? [closed]

  - by acjohnson55

  I am working on a web startup in the early stages, and we are struggling a bit to manage the scope and scheduling of our product. We have loads of high-level features in the pipeline, but we need a good way of scheduling them for release iterations and breaking them into actual tasks that can be scheduled (that could be a separate tool, but integration would be preferred). I would say that our product can be pretty cleanly divided into "aspects", and we want to be able to separate features by the aspect to which they apply. Perhaps most importantly, it should be really simple to create and move features between target release points. We don't have physical space for a war room type setup, so whatever we settle upon should ideally have a cloud-type web interface. Right now, we're using Excel to make a grid of product aspects vs. target releases, and we store features at the intersections. But this is not providing a good way of indexing tasks to those features or being able to move them around. I would much rather have something that automates the grid overview. I'm less interested in something that helps with low-level scheduling than I am in something that is good at organizing the product plan at the long-term, high-level view. Is there a product planning tool out there that matches these specifications?

  Read the article

• ubuntu 10.04: boot error for custom compiled kernel - gave up wating for root device

  - by atharva

  Hi, I have installed lucid on my Lenevo Laptop (Y 410 series , x86 platoform) and it is working fine. Now I have compiled kernel 2.6.37 from the downloaded from the kernel tree. I followed usual procedure of compileing kernel (make menuconfig,make. make modules etc). Then I created the initrd image using mkinitramfs and updated my grub using upadate grub command. Update-grub detects the initrd image of the compiled kernel. However when I boot from this kernel it gives me following error: Gave up waiting for root device. Common problems: -Boot args (cat /proc/cmdline) -Check rootdelay= (did the system wait long enough?) -Check root= (did the system wait for the right device?) -Missing modules (cat /proc/modules; ls /dev) ALERT! root=UUID=/... does not exist and then it falls onto initramfs prompt. I have tried following solutions discussed in different ubuntu forums: 1. disable uuid and point root=/dev/sda8 (sda8 is where my kernele image resides (both default kernel and compiled one) from /etc/default/grub 2. compile kernel using CONFIG_DEVTMPFS=y suggested here Still I am unable to boot from the compile kernel. Could someone please suggest me the solution ?

  Read the article

• Changing wallpaper depending on time of day via script or batch file?

  - by Patrick

  I want to have 2 different wallpapers that change according to time of day (6 and 22 hours respectively) and only want to display the night one after 22 hours and the day one only after 6 hours and until 22 hours. I didn't find a program that can do this after a standby, so I thought it should be easy to realize with the task scheduler running a script. Now the question is not only how to realize such a script, but also if the script should include the time checking or the task scheduler. I'm not sure what would work better with long times of the PC being in standby. I tried a few scripts already from similar questions and hoped I could modify to them to my needs, but they didn't work at all. Anyone able to help me? TIA.

  Read the article

• Lenovo v570 ubuntu 12.04 wireless hard blocked even when ext. switch is on

  - by user100987

  When I run iwconfig it say's lo and eth0 have no wireless extensions, but wlan0 it says IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS the:off Fragment the:off Power Management:off and I believe that's my problem, I just don't know how to turn it back on Any help? When I ran lspci | grep Network it gave me this 02:00.0 Network controller: Intell Corporation Centrino Wireless -N + WiMAX 6150 (rev 67) How I know that my wireless is hard blocked because when I run sudo rfkill list all I get 0: Ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes when I run lshw -c network I get. *-network DISABLED description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: mon1 version: 67 serial: 40:25:c2:d2:96:2c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-32-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:d0500000-d0501fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: f0:de:f1:d7:a0:4d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.65 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d0404000-d0404fff memory:d0400000-d0403fff

  Read the article

• How to cleanup tmp folder safely on Linux

  - by Syncopated

  I use RAM for my tmpfs /tmp, 2GB, to be exact. Normally, this is enough but sometimes, processes create files in there and fail to cleanup after themselves. This can happen if they crash. I need to delete these orphaned tmp files or else future process will run out of space on /tmp. How can I safely garbage collect /tmp? Some people do it by checking last modification timestamp, but this approach is unsafe because there can be long-running processes that still need those files. A safer approach is to combine the last modification timestamp condition with the condition that no process has a file handle for the file. Is there a program/script/etc that embodies this approach or some other approach that is also safe? Incidentally, does Linux/Unix allow a mode of file opening with creation wherein the created file is deleted when the creating process terminates, even if it's from a crash?

  Read the article

• Using iptables to block ALL outgoing traffic from one NIC?

  - by edanfalls

  Hi, I must pretty bad at Googling as this seems like a very basic question but I can't seem to find the answer anywhere... and man iptables is a very long read! I have two NICs - eth0 and eth1 - on a linux box and I want to block ALL outbound traffic (TCP and UDP across all ports) from one of the NICs, so that no traffic makes its way back up to the router. What is the command for this? I have only seen examples with specific ports. Thanks in advance.

  Read the article

• NAT Policy Inbound Source Problem on SonicWall TZ-210 with Multiple DSL Lines

  - by HK1

  We recently added three more DSL connections to our SonicWall TZ-210. My NAT Policies work fine as long as I leave them set with an inbound interface of X1, which hosts our original DSL connection. However, I'd like to change some of the NAT Policies to use inbound source/interface X2, X3, X4 or Any. In my initial tests, when I change one of the policies to use an inbound interface of X2, that port forward policy does not work at all. Traffic never makes it to the internal destination. What could be the problem?

  Read the article

• How do you proactively guard against errors of omission?

  - by Gabriel

  I'll preface this with I don't know if anyone else who's been programming as long as I have actually has this problem, but at the very least, the answer might help someone with less xp. I just stared at this code for 5 minutes, thinking I was losing my mind that it didn't work: var usedNames = new HashSet<string>(); Func<string, string> l = (s) => { for (int i = 0; ; i++) { var next = (s + i).TrimEnd('0'); if (!usedNames.Contains(next)) { return next; } } }; Finally I noticed I forgot to add the used name to the hash set. Similarly, I've spent minutes upon minutes over omitting context.SaveChanges(). I think I get so distracted by the details that I'm thinking about that some really small details become invisible to me - it's almost at the level of mental block. Are there tactics to prevent this? update: a side effect of asking this was fixing the error it would have for i 9 (Thanks!) var usedNames = new HashSet<string>(); Func<string, string> name = (s) => { string result = s; if(usedNames.Contains(s)) for (int i = 1; ; result = s + i++) if (!usedNames.Contains(result)) break; usedNames.Add(result); return result; };

  Read the article

• Debian 6 or CentOS 6 - which one is easiest for latest versions of Ruby and Postgres?

  - by A4J

  I am getting a new server as I've messed up my current box, while trying to install Postgres 9 (on my CentOS 5.8 box). To cut a long story short, I removed postgres but yum decided to remove virtualmin-base as well, which broke my virtualmin install (postfix/dovcot stopped working). Virtualmin advise a fresh install once virtualmin-base has been removed/reinstalled. So I'll probably make a decision based on this simple criteria: which distro out of the two makes it easiest for installing the latest versions of Ruby and Postgres? They are both equally respected as web servers, so I really don't mind either way - I just want to use the one that will work best with the software I need.

  Read the article

• Cannot access windows share

  - by Wrigley

  I have an accounting program specifically tailored to the IT industry, its called Fincon (exe based). It basically works on a client to server directory base system. the server is currently running on a windows 7 machine with a NTFS partition. I have installed Wine. Have the shared Windows directory mounted with what I assume is the correct command for such being (mount -tsmbfs //servername/sharedir /mnt/fincon -0 usename=username,password=password). I can see the shared dir although it does take a bit long to access it on the Ubuntu machine via the mapped directory but instant via normal network browsing. I have also set up the mapped directory to my D: drive in Wine and have pointed the fincon.ini to read server field from D: directly. Here's my issue, it seems that for some odd reason I cant write to the mapped directory from Ubuntu, yet I can with my Windows machines, the permissions are set correct on the Windows 7 share and I really dunno what I'm missing. I'm quite a Linux noob just switched yesterday. Thanks guys for any help in this would be quite appreciated. As I'm pulling out my hair here and really want to migrate my work PCs to a Linux OS as it just gives less issues than Windows does ever.

  Read the article

• Neverending issues with grub (ubuntu 14.04 on ASUS with Win8 dual boot)

  - by Mariana

  This is the most frustrating issue I have ever run into using Ubuntu and Windows in the same machine. I have an ASUS K46CB, 6GB RAM and preinstalled Windows 8.1 64-bits. I have successfully installed Ubuntu 14.04 LTS, also 64-bits. To do so,I followed this tutorial whenever possible. I only failed on the disable secure boot part: there is no 'Secure-boot' or even UEFI mention in my BIOS! Screenshots from other BIOS of the same model show the option under Boot, but in mine there is absolutely none. Because of this, I cannot boot into Ubuntu. The computer loads straight into Windows. I tried running boot repair, but got an error (i can show the log, but it's pretty long). Does anyone know how to fix this issue? UPDATE I reinstalled Ubuntu. Same problem, goes straight to Window. Boot-Repair informs me that i am using Windows in Legacy mode. It excecuted with no errors this time, but after restarting GRUB was still missing. I can't turn off Secure Boot yet. UPDATE I tried using Boot Repair to install grub on a boot-grub 1mb partition. Still boots straight to windows. I feel like punching something

  Read the article

• How to prevent one account from unlocking products on other devices using Apple StoreKit?

  - by reapz

  We are currently wrapping up a free-to-play game on iOS in which you can purchase non-consumable products. We have been discussing this case internally and are not quite sure what the best practices are as this is our first title. For example, if a user downloads our app, and makes some purchases. These can be restored should the app ever be deleted and reinstalled as long as the user uses the same Apple ID. What is to stop him from making a fake Apple account, purchasing items and then posting this account on the web allowing everyone to get the items for free? That is obviously a worst case situation. But a smaller case would be a user unlocking items for his friends. We do not want this to be an always online game but have considered doing a check on startup if there is internet available. If the currently logged in account doesn't own the products do we lock them again? Probably not because people may simply sign into the device with different Game Center logins at which point we don't want to constantly lock and unlock items. At some point we will be adding multiplayer at which point we can definately do a check with the currently logged in account. This is because A, they will be online when attempting multiplayer, and B, they will want to use their own account for multiplayer. Unfortunately we aren't quite ready for this yet. Has anyone tackled this issue. Are we overthinking here?

  Read the article

• Amazon EC2 vs Dedicated server at Hetzner, what's the use for EC2?

  - by C-Blu

  After searching the web I still can't find the reason to use EC2. What's the point to scale EC2? If you expect a huge burst in traffic, they say. OK, but what if you already have a couple of sites with good traffic, and for example medium reserved EC2 instance is not enough. You are paying $36.60(medium reserved for 1year) in EU(Ireland) + traffic + optional expenses for databases and S3 if you use them. Of course as some point when you are under $56.6-$66.1 you can optimize your hosting costs with Amazon EC2. But when you get at some point if purchase EX4 server from Hetzner, it will surpass your perfomance needs for a long time, before you get a massive traffic. (I am wrong?) CPU: i7-2600 Quadcore (3.4-3.8 Ghz) RAM: 16 GB HDD: 2x3 TB SATA (6 Gbit/s) - I think that disc performance of a dedicated is better then of Amazon EBS Traffic: 10 TiB in month included. This is what you get from Hetzner for $56(- 19% VAT) or $66 for EU residents. Please, tell me what's the reason to use Amazon? Which load won't a server from Hetzner take, but Amazon Auto Scaling will? The maintenance of dedicated vs EC2 is still the same? Or hardware failure at Amazon, won't ruin your EBS storage? I'm still not at the level when I need expensive hosting, but want to know beforehand, just to be sure if Amazon infrastructure is better then pure performance of Hetzner's hardware.

  Read the article

• Unity gizmos vs. referenced game objects

  - by DuckMaestro

  I'm designing a Unity script that I intend to be highly reusable and as easy as possible to setup within the editor. To this end, a number of properties of this script really need some kind of visual representation on screen. It is an unresolved question to me whether the design of the script should require references to placeholder game objects, OR just Vector3's and float's that have associated gizmos drawn for them. Normally a gizmo would be a natural choice, except that Unity gizmos are not directly manipulable (as far as I can tell). Because of this shortcoming I'm having to consider whether depending on references to placeholder game objects is a more designer-friendly approach ultimately, in spite of the extra setup required, and that it might be counter-intuitive when the placeholder game objects disappear at run-time (which my script would do). Is there a community standard or preference here in this case? Can a Unity-experienced game programmer / designer speak to which approach they feel is more intuitive or more convenient to setup, when using a 3rd party script? Or is this just splitting hairs as long as I ship an example prefab with my script?

  Read the article

• nVidia 9800 GTX+ X11 fails to initialize. no unity or lightdm

  - by rlemon

  I have just upgraded my work pc to 12.04 (not upgrade, fresh install), installing updates during the install, and after everything has loaded (with no errors) and I restart I get brought to console 1 tty login. Console 7 looks like this: IIRC I did not have to finagle with my drivers on 11.10 to get this card working. If this is in fact a driver bug I will remove this post and submit the bug but i'm not 100% confident that it is. I attempted to run unity --reset and got this: Lastly I tried $ sudo apt-get install nvidia-current which tells me nvidia-current is already the newest version. so I ran $ sudo dpkg-reconfigure nvidia-current which says /usr/sbin/dpkg-reconfigure: nvidia-current is broken or not fully installed. Anything I can try from here would be awesome. Currently the only way to get the system up and running was to shut down, plug one of my monitors into the onboard video, enable the onboard video card from the BIOS, then boot back up (and on my single monitor everything is fine). update So I have been able to boot fresh with the ext card plugged in as long as I don't take the updates with the install. past this if I only install the nvidia drivers (nvidia-current or nvidia-current-updates) from the main server (or canadian) I then get the problems.. My proposal; which I don't know where to look for: Can I try installing the previous version of this driver? In the past, on another machine I had issues with my NIC driver being funky... downgraded to the previous driver and bam everything was merry and well.

  Read the article

< Previous Page | 462 463 464 465 466 467 468 469 470 471 472 473  | Next Page >