Search Results

Search found 13224 results on 529 pages for 'redirection errors'.

Page 468/529 | < Previous Page | 464 465 466 467 468 469 470 471 472 473 474 475  | Next Page >

• Simple mdadm RAID 1 not activating spare

  - by Nick Liu

  I had created two 2TB HDD partitions (/dev/sdb1 and /dev/sdc1) in a RAID 1 array called /dev/md0 using mdadm on Ubuntu 12.04 LTS Precise Pangolin. The command sudo mdadm --detail /dev/md0 used to indicate both drives as active sync. Then, for testing, I failed /dev/sdb1, removed it, then added it again with the command sudo mdadm /dev/md0 --add /dev/sdb1 watch cat /proc/mdstat showed a progress bar of the array rebuilding, but I wouldn't spend hours watching it, so I assumed that the software knew what it was doing. After the progress bar was no longer showing, cat /proc/mdstat displays: md0 : active raid1 sdb1[2](S) sdc1[1] 1953511288 blocks super 1.2 [2/1] [U_] And sudo mdadm --detail /dev/md0 shows: /dev/md0: Version : 1.2 Creation Time : Sun May 27 11:26:05 2012 Raid Level : raid1 Array Size : 1953511288 (1863.01 GiB 2000.40 GB) Used Dev Size : 1953511288 (1863.01 GiB 2000.40 GB) Raid Devices : 2 Total Devices : 2 Persistence : Superblock is persistent Update Time : Mon May 28 11:16:49 2012 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 Name : Deltique:0 (local to host Deltique) UUID : 49733c26:dd5f67b5:13741fb7:c568bd04 Events : 32365 Number Major Minor RaidDevice State 1 8 33 0 active sync /dev/sdc1 1 0 0 1 removed 2 8 17 - spare /dev/sdb1 I've been told that mdadm automatically replaces removed drives with spares, but /dev/sdb1 isn't being moved into the expected position, RaidDevice 1. UPDATE (30 May 2012): A badblocks destructive read-write test of the entire /dev/sdb yielded no errors as expected; both HDDs are new. As of the latest edit, I assembled the array with this command: sudo mdadm --assemble --force --no-degraded /dev/md0 /dev/sdb1 /dev/sdc1 The output was: mdadm: /dev/md0 has been started with 1 drive (out of 2) and 1 rebuilding. Rebuilding looks like it's progressing normally: md0 : active raid1 sdc1[1] sdb1[2] 1953511288 blocks super 1.2 [2/1] [U_] [>....................] recovery = 0.6% (13261504/1953511288) finish=2299.7min speed=14060K/sec unused devices: <none> I'm now waiting on this rebuild, but I'm expecting /dev/sdb1 to become a spare just like the five or six times that I've tried rebuilding before. UPDATE (31 May 2012): Yeah, it's still a spare. Ugh! UPDATE (01 June 2012): I'm trying Adrian Kelly's suggested command: sudo mdadm --assemble --update=resync /dev/md0 /dev/sdb1 /dev/sdc1 Waiting on the rebuild now... My questions are: Why isn't the spare drive becoming active sync? How can I make the spare drive become active?

  Read the article

• 502 Bad Gateway with nginx + apache + subversion + ssl (SVN COPY)

  - by theplatz

  I've asked this on stackoverflow, but it may be better suited for serverfault... I'm having a problem running Apache + Subversion with SSL behind an Nginx proxy and I'm hoping someone might have the answer. I've scoured google for hours looking for the answer to my problem and can't seem to figure it out. What I'm seeing are "502 (Bad Gateway)" errors when trying to MOVE or COPY using subversion; however, checkouts and commits work fine. Here are the relevant parts (I think) of the nginx and apache config files in question: Nginx upstream subversion_hosts { server 127.0.0.1:80; } server { listen x.x.x.x:80; server_name hostname; access_log /srv/log/nginx/http.access_log main; error_log /srv/log/nginx/http.error_log info; # redirect all requests to https rewrite ^/(.*)$ https://hostname/$1 redirect; } # HTTPS server server { listen x.x.x.x:443; server_name hostname; passenger_enabled on; root /path/to/rails/root; access_log /srv/log/nginx/ssl.access_log main; error_log /srv/log/nginx/ssl.error_log info; ssl on; ssl_certificate server.crt; ssl_certificate_key server.key; add_header Front-End-Https on; location /svn { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; set $fixed_destination $http_destination; if ( $http_destination ~* ^https(.*)$ ) { set $fixed_destination http$1; } proxy_set_header Destination $fixed_destination; proxy_pass http://subversion_hosts; } } Apache Listen 127.0.0.1:80 <VirtualHost *:80> # in order to support COPY and MOVE, etc - over https (443), # ServerName _must_ be the same as the nginx servername # http://trac.edgewall.org/wiki/TracNginxRecipe ServerName hostname UseCanonicalName on <Location /svn> DAV svn SVNParentPath "/srv/svn" Order deny,allow Deny from all Satisfy any # Some config omitted ... </Location> ErrorLog /var/log/apache2/subversion_error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/subversion_access.log combined </VirtualHost> From what I could tell while researching this problem, the server name has to match on both the apache server as well as the nginx server, which I've done. Additionally, this problem seems to stick around even if I change the configuration to use http only.

  Read the article

• How to get wireless working (properly) with Sitecom Wireless USB micro adapter 300N on Windows 7?

  - by Timo

  The question says it all, but more detail follows ;) I've got a new computer that runs Windows 7 64-bits (Home Edition) and I'd like to connect it to my wireless home network (Sitecom wireless gigabit router 300N wl-352 v1 002) with a Sitecom wireless USB micro adaptapter 300 wl-352 V2 001. After installing the router (i.e. connected to the modem and power) and ensuring that wireless is indeed enabled, I've installed the driver of the USB adapter on the new computer described above. After the installation (drivers and utility on CD) completes successfull I rebooted my computer and inserted the USB adapter. After discovering the right network and connecting to it using the network key, a connection is succesfully made. (Using the Sitecom 300N USB Wireless LAN utility). In the LAN utility I can see that the signal strength is approximately 50% and connection quality is approximately 80%. Judging from these numbers I assumed that all was fine and started to use the connection (reading news on nu.nl, a dutch news site), but noticed that the connection was lost several times in a very short time span, but each time the connections was resumed, resulting in the 50/80 percent numbers described above. However, the website was not loaded completely and often a timeout would be reported. When inspecting the drivers through Device Management (Windows' Apparaatbeheer in dutch) there were no errors/warnings; everything seemed to be in order. In an attempt to solve this, I downloaded the latest drivers for the USB adapter, but the problems remained. Finally I tried to connect the computer with a Siemens Gigaset USB Adapter 108. This process was a troublesome since I had to download a driver (from the site above) and tell Windows (7) to use the Windows Vista driver when installing the new hardware, since there is (was) no Windows 7 driver available. This resulted in a usable connection, although not very stable when reconfiguring the router. Which took the form of selecting a different wireless channel on the router, even using the Sitecom utility mentioned above to check if there were other networks communicating on that channel (and thus picking a channel that was not used by other networks). Again no result when changing back to the Sitecom USB adapter. Note that this means (I think) that I could use the internet connection with the Siemens adapter, meaning the problem was not in the router. So: How to get wireless working (properly) with Sitecom Wireless USB micro adapter 300N on Windows 7? PS Sorry, but should be able to post one link, while I had links in place for the USB adapter, router and the siemens adapter in place as well, but I'm not (yet) allowed to post these... (The site says I can post one link, but only when no links are present will it allow me to post the question...)

  Read the article

• Ubuntu 12.04 crash analysis - strange binary data on all open files at the moment of crash

  - by lanbo

  A couple of hours ago we got a system crash on Ubuntu 12.04. We checked all the log files and there is nothing suspicious to blame to. Last stuff that was logged was some dovecot activity. There are no kernel panic messages. Nothing. It is a new server (new hardware) we are testing before production. And because it is new hard, I'm suspicious the problem may be due to some faulty hardware. We already run memtester with no problem detected. I'll be happy to hear from other hardware testing tools (the machine has SSD). Anyway, the thing I wanted to ask you is a different one. The strange thing is on every open file at the moment of the crash we found the next sequence of symbols was written into them: "@^@^@^@^@^@^@...". For example, on the syslog log file we got: Apr 16 15:53:56 odyssey dovecot: pop3-login: Aborted login (auth failed, 1 attempts): user=<info>, method=PLAIN, rip=46.29.255.73, lip=5.9.58.177 ^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^ [these continues for about 1000 chars...] ^@^@^@^@Apr 16 15:55:12 odyssey kernel: imklog 5.8.6, log source = /proc/kmsg started. We got all these symbols in all open files. These include: syslog, mail.log, kern.log, ... But also on some logs that are output by php scripts run in CRONs from user accounts (not root). So, any idea why all open files got these characters written during the crash? This is pretty bad since the crash corrupted many files (we don't even know which other ones may be affected). We are suspicious that all open files (in write mode maybe) at the moment of the crash got all these symbols inserted. Why is that? BTW [in case it helps], the system automatically rebooted after the crash but Apache did not start. There were not traces in /var/apache2/*log why apache did not start. After running a "service apache2 start" it started with no problems. Also, we rebooted the machine manually and Apache also started on reboot. But it did not start after the crash and no errors were reported. Thanks guys!

  Read the article

• Raid1 with active and spare partition

  - by Daniel Baron

  I am having the following problem with a RAID1 software raid partition on my Ubuntu system (10.04 LTS, 2.6.32-24-server in case it matters). One of my disks (sdb5) reported I/O errors and was therefore marked faulty in the array. The array was then degraded with one active device. Hence, I replaced the harddisk, cloned the partition table and added all new partitions to my raid arrays. After syncing all partitions ended up fine, having 2 active devices - except one of them. The partition which reported the faulty disk before, however, did not include the new partition as an active device but as a spare disk: md3 : active raid1 sdb5[2] sda5[1] 4881344 blocks [2/1] [_U] A detailed look reveals: root@server:~# mdadm --detail /dev/md3 [...] Number Major Minor RaidDevice State 2 8 21 0 spare rebuilding /dev/sdb5 1 8 5 1 active sync /dev/sda5 So here is the question: How do I tell my raid to turn the spare disk into an active one? And why has it been added as a spare device? Recreating or reassembling the array is not an option, because it is my root partition. And I can not find any hints to that subject in the Software Raid HOWTO. Any help would be appreciated. Current Solution I found a solution to my problem, but I am not sure that this is the actual way to do it. Having a closer look at my raid I found that sdb5 was always listed as a spare device: mdadm --examine /dev/sdb5 [...] Number Major Minor RaidDevice State this 2 8 21 2 spare /dev/sdb5 0 0 0 0 0 removed 1 1 8 5 1 active sync /dev/sda5 2 2 8 21 2 spare /dev/sdb5 so readding the device sdb5 to the array md3 always ended up in adding the device as a spare. Finally I just recreated the array mdadm --create /dev/md3 --level=1 -n2 -x0 /dev/sda5 /dev/sdb5 which worked. But the question remains open for me: Is there a better way to manipulate the summaries in the superblock and to tell the array to turn sdb5 from a spare disk to an active disk? I am still curious for an answer.

  Read the article

• windows 2008 R2 TS printer security - can't take owership

  - by Ian

  I have a Windows 2008 R2 server with Terminal server role installed. I'm seeing a problem with an ordinary user who is member of local printer operators group on the server. If the user opens a cmd window using ‘run as administrator’ they can run printmanager.msc without needing to enter their password again. In printmanager they can change the ownership of redirected (easy print) printers without problems. If, from the same cmd window, they use subinacl to try and change the onwership of the queue to themselves they get access denied: >subinacl.exe /printer "_#MyPrinter (2 redirected)" /setowner="MyDom\MyUsr" Elapsed Time: 00 00:00:00 Done: 1, Modified 0, Failed 1, Syntax errors 0 Last Done : _#MyPrinter (2 redirected) Last Failed: _#MyPrinter (2 redirected) - OpenPrinter Error : 5 Access denied so, same context, same action but one works and one doesn't. Any ideas for this odd behaviour? I'm using subinacl x86 on an x64 server as I can't find anything more up to date. I've tried with icacls and others but couldn't get them to do anything with printers. EDIT: added after Gregs comments regarding setacl below If I log into the TS server as Testusr and open Admin Tools Printer Admin (as administrator) and then type mydomain\testusr and the testusr's password, then I can change the ownership of the printer queue and set testusr as the owner. However if I open cmd as administrator and, again, type mydomain\testusr and the users password when I try to change the ownership of my redirected printer I get the following: C:\>setacl -on "Bullzip PDF Printer (12 redireccionado)" -ot prn -actn setowner -ownr n:mydom\testusr WARNING: Privilege 'Back up files and directories' could not be enabled. SetACL's powers are restricted. WARNING: Privilege 'Restore files and directories' could not be enabled. SetACL's powers are restricted. INFORMATION: Processing ACL of: <Bullzip PDF Printer (12 redireccionado)> ERROR: Enabling the privilege SeTakeOwnershipPrivilege failed with: No todos los privilegios o grupos a los que se hace referencia son asignados al llamador. [meaning not all referenced privs or groups are assigned to the caller] SetACL finished with error(s): SetACL error message: A privilege could not be enabled maybe I'm getting something wrong but if the built in windows tool can do it with just membership of the 'print operators' group then setacl should be able to as well, no? However setacl seems to depend on other privileges, which in reality are not required to do this.

  Read the article

• Mercurial browser on Windows 2003 takes several refreshes before displaying repositories

  - by Tim Murphy

  When attempt to browse my Mercurial repositories it usually takes several refreshes before the repository list is displayed. The configuration is as follows: Windows Server 2003 (Dedicated machine hosted by http://www.server4you.com/. Site has anonymous password protection with self-signed SSL. Mercurial 1.5.3 Python 2.6.5 Python for Windows 32 extensions 214 py2.6 isapi-wsgi 0.4.2 The repositories are being served via ISAPI using the standard hgwebdir_wspi.py file (copy to follow). Other problems with the repository server: Before doing a clone/push/etc I have to browse the repositories first otherwise hg on my local machine can not locate the site. I have one a repository with a large changeset that after a minute or so throw error "abort: error: An existing connection was forcibly closed by the remote host". Will be asking another question for this problem. What can I do to start tracking down this problem? hgwebdir_wsgi.py # Configuration file location hgweb_config = r'C:\Public\Mercurial\WebSite\hgweb.config' # Global settings for IIS path translation path_strip = 0 # Strip this many path elements off (when using url rewrite) path_prefix = 0 # This many path elements are prefixes (depends on the # virtual path of the IIS application). import sys # Adjust python path if this is not a system-wide install #sys.path.insert(0, r'c:\path\to\python\lib') # Enable tracing. Run 'python -m win32traceutil' to debug if hasattr(sys, 'isapidllhandle'): import win32traceutil # To serve pages in local charset instead of UTF-8, remove the two lines below import os os.environ['HGENCODING'] = 'UTF-8' import isapi_wsgi from mercurial import demandimport; demandimport.enable() from mercurial.hgweb.hgwebdir_mod import hgwebdir # Example tweak: Replace isapi_wsgi's handler to provide better error message # Other stuff could also be done here, like logging errors etc. class WsgiHandler(isapi_wsgi.IsapiWsgiHandler): error_status = '500 Internal Server Error' # less silly error message isapi_wsgi.IsapiWsgiHandler = WsgiHandler # Only create the hgwebdir instance once application = hgwebdir(hgweb_config) def handler(environ, start_response): # Translate IIS's weird URLs url = environ['SCRIPT_NAME'] + environ['PATH_INFO'] paths = url[1:].split('/')[path_strip:] script_name = '/' + '/'.join(paths[:path_prefix]) path_info = '/'.join(paths[path_prefix:]) if path_info: path_info = '/' + path_info environ['SCRIPT_NAME'] = script_name environ['PATH_INFO'] = path_info return application(environ, start_response) def __ExtensionFactory__(): return isapi_wsgi.ISAPISimpleHandler(handler) if __name__=='__main__': from isapi.install import * params = ISAPIParameters() HandleCommandLine(params) hgweb.config [paths] / = C:\Public\Mercurial\Repositories\* [web] allow_archive = bz2 gz zip ; Allows archive downloads. allow_push = ######## ; Users that are allowed to push.

  Read the article

• Package problems after upgrade

  - by Dan

  I installed a new upgrade on ubuntu which seemed to fail near the end. Now I'm being told that an error has occurred and to please run apt-get to see what's wrong. After some further tries with that I eventually gave up. It seems there's a left over latex package(?) somewhere and I can't seem to get rid of or fix it. Here's an example: blank@ubuntu:~$ sudo apt-get dist-upgrade Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these. The following packages have unmet dependencies: tex-common : Breaks: texlive-common (< 2010) but 2009-15 is installed texlive-base : Depends: texlive-binaries (>= 2012.20120516) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-doc-base : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-extra-utils : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed texlive-font-utils : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-generic-recommended : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-base : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-base-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-extra : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-extra-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-recommended : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-recommended-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-luatex : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-pictures : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-pictures-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-pstricks : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-pstricks-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed zlib1g : Breaks: texlive-binaries (< 2009-12) but 2009-11ubuntu2 is installed zlib1g:i386 : Breaks: texlive-binaries (< 2009-12) but 2009-11ubuntu2 is installed E: Unmet dependencies. Try using -f. I've seen similar errors on the site here, but not close enough that i could get it fixed. Any help would be great, Thanks

  Read the article

• How to resolve `bootpd` crashing constantly on Mac OS X 10.6.4 Snow Leopard Server?

  - by morgant

  I've got a Mac Pro running Mac OS X 10.6.4 Snow Leopard Server and it's recently started getting numerous 'kNetworkError's in Server Admin.app when viewing services. It's acting as a gateway w/NAT and has been so for quite some time. There is one glaring issue, bootpd crashes all the time with the following errors in `/var/log/system.log/: Aug 12 16:54:59 servername bootpd[3572]: server starting Aug 12 16:54:59 servername bootpd[3572]: server name servername.domain.tld Aug 12 16:54:59 servername bootpd[3572]: interface en0: ip 10.0.1.9 mask 255.255.255.0 Aug 12 16:54:59 servername bootpd[3572]: bsdpd: re-reading configuration Aug 12 16:54:59 servername bootpd[3572]: bsdpd: shadow file size will be set to 48 megabytes Aug 12 16:54:59 servername bootpd[3572]: bsdpd: age time 00:15:00 Aug 12 16:54:59 servername bootpd[3572]: [3572] detected buffer overflow Aug 12 16:54:59 servername com.apple.launchd[1] (com.apple.bootpd[3572]): Job appears to have crashed: Abort trap Aug 12 16:54:59 servername com.apple.ReportCrash.Root[3571]: 2010-08-12 16:54:59.828 ReportCrash[3571:2807] Saved crash report for bootpd[3572] version ??? (???) to /Library/Logs/DiagnosticReports/bootpd_2010-08-12-165459_localhost.crash It is correctly configured to serve DHCP through en1 (not en0), the "LAN" port. This happens even with no hardware (even switches) connected to the "LAN" port. There are no DHCP clients listed. Oddly, the "Overview" shows 1 static map, but nothing is listed under "Static Maps" and there are no "Computers" in Open Directory. /var/db/dhcp_leases is empty. /Library/Logs/DiagnosticReports/bootpd_2010-08-12-165459_localhost.crash is as follows: Process: bootpd [3572] Path: /usr/libexec/bootpd Identifier: bootpd Version: ??? (???) Code Type: X86-64 (Native) Parent Process: launchd [1] Date/Time: 2010-08-12 16:54:59.713 -0400 OS Version: Mac OS X Server 10.6.4 (10F569) Report Version: 6 Exception Type: EXC_CRASH (SIGABRT) Exception Codes: 0x0000000000000000, 0x0000000000000000 Crashed Thread: 0 Dispatch queue: com.apple.main-thread Application Specific Information: __abort() called Thread 0 Crashed: Dispatch queue: com.apple.main-thread 0 libSystem.B.dylib 0x00007fff803c13d6 __kill + 10 1 libSystem.B.dylib 0x00007fff80461913 __abort + 103 2 libSystem.B.dylib 0x00007fff80456157 mach_msg_receive + 0 3 libSystem.B.dylib 0x00007fff803b92cf __strncpy_chk + 14 4 bootpd 0x0000000100014e5d PLCache_read + 782 5 bootpd 0x0000000100004a3d BSDPClients_init + 68 6 bootpd 0x00000001000053b5 bsdp_init + 2396 7 bootpd 0x000000010000200b S_update_services + 1228 8 bootpd 0x0000000100002344 S_server_loop + 571 9 bootpd 0x0000000100003963 main + 1766 10 bootpd 0x0000000100000984 start + 52 Thread 0 crashed with X86 Thread State (64-bit): rax: 0x0000000000000000 rbx: 0x00007fff5fbfe220 rcx: 0x00007fff5fbfe218 rdx: 0x0000000000000000 rdi: 0x0000000000000df4 rsi: 0x0000000000000006 rbp: 0x00007fff5fbfe240 rsp: 0x00007fff5fbfe218 r8: 0x0000000000000001 r9: 0x0000000100114280 r10: 0x00007fff803bd412 r11: 0xffffff80002e1680 r12: 0xffffffffffffffff r13: 0x00007fff5fbfe330 r14: 0x00007fff5fbfe33b r15: 0x00007fff7009bec0 rip: 0x00007fff803c13d6 rfl: 0x0000000000000202 cr2: 0x000000010004c000 Any thoughts or suggestions as to resolving this?

  Read the article

• Weird IIS with Windows Authentication + IE problem

  - by Paulius Maruška

  I have a website running on IIS and using Windows Authentication. All users that are configured to get access to the site are form a AD domain (not local users). In the properties of a Website, I have set to use the AD domain as the realm. Now, when using Firefox, Safari or Chrome - Everything is fine. When the user tries to open the site, he get's the login box. he enters simply "username" and "password" (let's pretend that it's an actual login and password :P) and he get's into the site. When using IE, however, things get nasty. When the user tries to open the site - he get's the login box. User enters the "username" and "password" again, but those get rejected! And when the second time login box pops up - it has the username filled in as "web-server-domain-name\username" which is wrong, because web-server-domain-name is not the domain where all users reside (it's "ad-domain"). I've spent days trying to figure out what's going on... Note, that if I manually enter "ad-domain\username" - I get accepted into the site without problems. So, my guess is that IE sends wrong username if domain is not specified. Anyway, IE is the only browser that triggers this behavior! Is it possible to do a server-side fix? Maybe it's possible to somehow auto-map the users to AD users? If it's not solvable server-side - is there a client-side fix for this? Thank you. PS: I'm more of a programmer than a sys-admin, so configuring servers isn't the strong side of mine... :P UPDATE: @Evan: Yes, "Digest authentication for Windows domain servers" is also enabled. @Eric: IIS version is 6.0. The authentication methods enabled are: Integrated and digest - all other methods are disabled. As for the security log. I looked at it, when doing "username" and "password" login in Chrome/Firefox and when doing "ad-domain\username" and "password" login from IE - the generated log messages are the same (I see no difference, anyway). When entering "username" and "password" I don't see any errors in the security (or any other) log, so can't tell what method it's trying to use. UPDATE 2: As suggested by Eric in the comments - I played around with Fiddler... While playing with it, I noticed, that when "username" and "password" is entered in FF and IE - the "Authorization" header value (encrypted) sent by IE is longer (almost two times) than one sent by FF. I tried to disable Windows Integrated authentication and only leave the Digest enabled - that fixed the problem (meaning, IE used the right realm just like other browsers), but that caused bazillion other problems with my site, because with Digest - user impersonation on the server doesn't work (that causes problems, when connecting to database etc). Any ideas?

  Read the article

• Wirelss card not being detected in backtrack 5

  - by Jesse Nelson

  I just installed backtrack 5 and I am unable to detect my wireless card. iwconfig doesn't list my interface. I can see that the hardware is present in lspci -vnn (see below) but I can't get the interface detected. I have tried to reinstall the compat-wireless package but I get errors during the build (see below) I have done a ton of researching and I keep hitting a brick wall, mostly because the wiki for backtrack is down and I can't find any good resources. Does anyone know how to fix the issue? Also, does anyone no how I can scan the hardware to determine what NIC is assigning my interface? If I can figure out the interface name I think I can set it up manually by putting up the link and using wireless-tools to manually configure the connection, this is what I had to do in arch on my mac. As stated the wiki for backtrack is down and I can't find any help on the issue. I tried to do the full kernel upgrade suggested in my software update but after the update was complete and I logged back in I had a new log in manager and the only thing I was able to log into was window managers. However, after this update my wireless was working fine. Please help I am new to Linux and the wiki is down, I have nowhere else to turn. Forgot to mention I am using the KDE version, not Gnome. Thanks in advance for any help or support. Attempt at make: root@bt:/usr/src/compat-wireless-3.3-rc1-2# make /usr/src/compat-wireless-3.3-rc1-2/config.mk:254: "WARNING: CONFIG_CFG80211_WEXT will be deactivated or not working because kernel was compiled with CONFIG_WIRELESS_EXT=n. Tools using wext interface like iwconfig will not work. To activate it build your kernel e.g. with CONFIG_LIBIPW=m." make -C /lib/modules/2.6.38/build M=/usr/src/compat-wireless-3.3-rc1-2 modules make: *** /lib/modules/2.6.38/build: No such file or directory. Stop. make: *** [modules] Error 2 lspci output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn -i net lspci: I/O error at net, line 0 root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn 02:00.0 Network controller [0280]: Atheros Communications Inc. Device [168c:0032] (rev ff) (prog-if ff) !!! Unknown header type 7f ( This is the problem but I can't find the solution) Kernel modules: ath9k iwconfig output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# iwconfig lo no wireless extensions. eth0 no wireless extensions.

  Read the article

• Error: Multilib version problems found

  - by Kovács Ákos

  What causes this error? Error: Multilib version problems found. This often means that the root cause is something else and multilib version checking is just pointing out that there is a problem. Eg.: 1. You have an upgrade for glibc which is missing some dependency that another package requires. Yum is trying to solve this by installing an older version of glibc of the different architecture. If you exclude the bad architecture yum will tell you what the root cause is (which package requires what). You can try redoing the upgrade with --exclude glibc.otherarch ... this should give you an error message showing the root cause of the problem. 2. You have multiple architectures of glibc installed, but yum can only see an upgrade for one of those arcitectures. If you don't want/need both architectures anymore then you can remove the one with the missing update and everything will work. 3. You have duplicate versions of glibc installed already. You can use "yum check" to get yum show these errors. ...you can also use --setopt=protected_multilib=false to remove this checking, however this is almost never the correct thing to do as something else is very likely to go wrong (often causing much more problems). Protected multilib versions: glibc-2.12-1.107.el6_4.5.i686 != glibc-2.12-1.107.el6_4.2.x86_64 Error: Protected multilib versions: db4-4.7.25-18.el6_4.i686 != db4-4.7.25-17.el6.x86_64 You could try using --skip-broken to work around the problem ** Found 10 pre-existing rpmdb problem(s), 'yum check' output follows: 32:bind-libs-9.8.2-0.17.rc1.el6_4.6.x86_64 is a duplicate with 32:bind-libs-9.8.2-0.17.rc1.el6_4.5.x86_64 chkconfig-1.3.49.3-2.el6_4.1.x86_64 is a duplicate with chkconfig-1.3.49.3-2.el6.x86_64 db4-4.7.25-18.el6_4.x86_64 is a duplicate with db4-4.7.25-17.el6.x86_64 12:dhcp-common-4.1.1-34.P1.el6_4.1.x86_64 is a duplicate with 12:dhcp-common-4.1.1-34.P1.el6.centos.x86_64 glibc-2.12-1.107.el6_4.5.x86_64 is a duplicate with glibc-2.12-1.107.el6_4.2.x86_64 glibc-common-2.12-1.107.el6.x86_64 has missing requires of glibc = ('0', '2.12', '1.107.el6') glibc-common-2.12-1.107.el6_4.2.x86_64 is a duplicate with glibc-common-2.12-1.107.el6.x86_64 glibc-common-2.12-1.107.el6_4.5.x86_64 is a duplicate with glibc-common-2.12-1.107.el6_4.2.x86_64 krb5-libs-1.10.3-10.el6_4.6.x86_64 is a duplicate with krb5-libs-1.10.3-10.el6_4.4.x86_64 tzdata-2013g-1.el6.noarch is a duplicate with tzdata-2013c-2.el6.noarch

  Read the article

• Unable to telnet out on port 25 on windows server 2008

  - by NickGPS

  Hi All, I just setup a Windows 2008 R2 server and am trying to get a basic mail server up and running so that I can send emails from my applications. I setup a virtual SMTP server in IIS6 and tried doing a local telnet to port 25, which seemed to work fine. There were no errors during this stage and I can see the mail message appear in the Queue folder. The problem is that mail never leaves the Queue folder. I then tried to telnet to a remote mail server on port 25 but couldn't connect:- telnet 209.85.227.27 25 Could not open connection to the host, on port 25: Connection failed) I checked my firewall and there is a default setting to allow all outgoing TCP traffic with no restriction. I even setup a specific rule for outgoing port 25 traffic but to no avail. I then ran a SmtpDiag.exe command .\SmtpDiag.exe [email protected] [email protected] and received the following output Searching for Exchange external DNS settings. Computer name is WIN-SERVERNAME. Failed to connect to the domain controller. Error: 8007054b Checking SOA for gmail.com. Checking external DNS servers. Checking internal DNS servers. SOA serial number match: Passed. Checking local domain records. Checking MX records using TCP: gmail.com. Checking MX records using UDP: gmail.com. Both TCP and UDP queries succeeded. Local DNS test passed. Checking remote domain records. Checking MX records using TCP: gmail.com. Checking MX records using UDP: gmail.com. Both TCP and UDP queries succeeded. Remote DNS test passed. Checking MX servers listed for [email protected]. Connecting to gmail-smtp-in.l.google.com [209.85.227.27] on port 25. Connecting to the server failed. Error: 10060 Failed to submit mail to gmail-smtp-in.l.google.com. Is there any other diagnostics I can do to figure out if it's my firewall or something else? I have removed antivirus to make sure that it wasn't causing the problem. Any ideas would be much appreciated.

  Read the article

• Windows Server 2008 Software Raid 5 - Data integrity issues

  - by Fopedush

  I've got a server running Windows Server 2008 R2, with a (windows native) software raid-5 array. The array consists of 7x 1TB Western Digital RE3 and RE4 drives. I have offline backups of this array. The problem is this: I noticed a few days ago after copying a large file to the disk that there was an integrity issue with that file - it was a ~12GB file that I had downloaded via uTorrent. After moving it to the raid array, I used uTorrent to relocate the download location, and performed a re-check so I could seed it from that location. The recheck found that only 6308/6310 chunks of the copied file were intact. My next step was to write a quick powershell script that would copy files to the array, while performing a SHA1 hash of the original and resultant files and comparing them. Smaller files (100-1000MB) copied over just fine. When I started copying larger data (~15GB), I found that the hash check failed about 2/3rds of the time. The corrupt files had very, very small inconsistencies - less than .01%. I further eliminated the possibility of networking or client issues by placing this large file on the C:\ of the server, and copying it repeatedly from there to the array, seeing similar results. Copying the data via explorer, powershell, or the standard windows command prompt yield the same results. None of the copies fail or report any problems. The raid array itself is listed as healthy in disk management. After a few experiments, I shut down the server and ran memtest overnight. No errors were detected. A basic run of chkdsk found no problems, but I did not use the /R flag, as I was unsure how that might affect a software raid-5 volume. I next ran Crystal Disk Info to check the smart data on the drives - but found that CDI only detected 5 out of 7 of the disks in the array. I have no idea why. Nevertheless, CDI shows the following "caution" flags on a single one of the drives: 05 199 199 140 000000000001 Reallocated Sectors Count C5 200 200 __0 000000000001 Current Pending Sector Count Which is a little bit alarming, but I don't really know what to do with the information. I hardly feel like one reallocated sector could be causing this. At this point, I'm looking for some guidance on what to do next. I need to determine the cause of this issue, but I'm hesitant to run chkdsk /R or any bootable disk health checkers because I'm afraid they might break the array. I've considered triggering a re-sync of the array, but I'm not actually sure how to do that without doing something silly like manually dropping a disk and then restoring it. Any advice that could help me ferret out the precise cause of this issue would be greatly appreciated.

  Read the article

• How to conform to update-rc.d with LSB standard?

  - by user34881

  This is a migrated question from stackoverflow, as I was told, this is the place for it to be. http://stackoverflow.com/questions/2263567/how-to-conform-to-update-rc-d-with-lsb-standard I have set up a simple script to back up some directories. While I haven't had any problems setting up the functionality, I'm stuck with adding the script to rcX.d dir's using update-rc.d. My script: #! /bin/sh ### BEGIN INIT INFO # Provides: backup # Required-Start: backup # Required-Stop: # Should-Stop: # Default-Start: 0 6 # Default-Stop: # Description: Backs up some dirs ### END INIT INFO check_mounted() { # Check if HD is mounted } do_backup() { if check_mounted; then # Some rsync statements. fi } case "$1" in start) do_backup ;; restart|reload|force-reload) echo "Error: argument '$1' not supported" >&2 exit 3 ;; stop|"") # No-op ;; *) echo "Usage: backup [start]" >&2 exit 3 ;; esac : Using update-rc.d backup start 10 0 6 . I get the following warnings and errors: update-rc.d: warning: backup start runlevel arguments (none) do not match LSB Default-Start values (0 6) update-rc.d: warning: backup stop runlevel arguments (0 6.) do not match LSB Default-Stop values (none) update-rc.d: error: start|stop arguments not terminated by "." The syntax I try to use is the following: update-rc.d [-n] <basename> start|stop NN runlvl [runlvl] [...] . Google wasn't that helpful at finding a solution. How can I correctly set up a script and add it via update-rc.d? I'm using Ubuntu 9.10. UPDATE Using update-rc.d backup start 10 0 6 . stop 10 0 . the error disappears. The warnings about default values persists: update-rc.d: warning: backup start runlevel arguments (none) do not match LSB Default-Start values (0 6) update-rc.d: warning: backup stop runlevel arguments (0 6 0 6) do not match LSB Default-Stop values (none) It even is added to the appropiate rcX-dirs but it still does not get executed...

  Read the article

• How to Setup Ubuntu Mail Server with Google Apps?

  - by Apreche

  I have a domain, let's call it foobar.com. All of the MX records for foobar.com point to Google's mail servers because I am using Google Apps for your domain to manage it. It's great because everyone gets all the advantages of GMail, but our e-mail addresses aren't @gmail.com. I also have a server. Primarily, it's a web server, but it also serves other things. One of the things it serves is the web site for foobar.com and also sites for various virtual hosts such as shop.foobar.com and forum.foobar.com. The server is running Ubuntu 8.04, because I like using LTS releases in production. The thing is, there are various applications running on the server that need the ability to send out emails. Various applications, like the cron jobs, send me e-mails in case of errors. Some of the web applications need to send e-mail to users when they forget their passwords, to confirm new registered users, etc. Lastly, it's nice to be able to send e-mail from the command line using the mail command, or mutt. How can I setup the mail on the web server to go through the Google apps mail servers? I don't need the web server to receive mail, though that would be cool. I do need it to be able to send mail as any legitimate address @foobar.com. That way the forum application can send mails with [email protected] in the from field, and the ecommerce application will have [email protected] in the from field. Also, by sending the mail through the Google servers, we can avoid a lot of the problems with the e-mails being blocked by various spam filters on the web. Google's SMTP servers are trusted a lot more than mine would be. I'm pretty good with administering Linux systems, but I am absolutely brain dead when it comes to e-mail. I need step by step directions from beginning to end on how to set this up. I need to know every thing to install, and every single change to the configuration files that is necessary. I have tried following various howtos and guides in the past, but none of them were quite right. Either they didn't work at all, or they offered a configuration that is not what I wanted. Please help. Thanks.

  Read the article

• Exchange IMAP4 connector - Error Event ID 2006

  - by MikeB

  Hi, A couple of users in my organisation use IMAP4 to connect to Exchange 2007 (Update rollup 9 applied) because they prefer Thunderbird / Postbox clients. One of the users is generating errors in the Application Log as follows: An exception Microsoft.Exchange.Data.Storage.ConversionFailedException occurred while converting message Imap4Message 1523, user "*******", folder *********, subject: "******", date: "*******" into MIME format. Microsoft.Exchange.Data.Storage.ConversionFailedException: Message content has become corrupted. ---> System.ArgumentException: Value should be a valid content type in the form 'token/token' Parameter name: value at Microsoft.Exchange.Data.Mime.ContentTypeHeader.set_Value(String value) at Microsoft.Exchange.Data.Storage.MimeStreamWriter.WriteHeader(HeaderId type, String data) at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimeStreamAttachment(StreamAttachmentBase attachment, MimeFlags flags) --- End of inner exception stack trace --- at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimeStreamAttachment(StreamAttachmentBase attachment, MimeFlags flags) at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimeAttachment(MimePartInfo part, MimeFlags flags) at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimePart(MimePartInfo part, MimeFlags mimeFlags) at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimeParts(List`1 parts, MimeFlags mimeFlags) at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimePart(MimePartInfo part, MimeFlags mimeFlags) at Microsoft.Exchange.Data.Storage.ImapItemConverter.<>c__DisplayClass2.<WriteMimePart>b__0() at Microsoft.Exchange.Data.Storage.ConvertUtils.CallCts(Trace tracer, String methodName, String exceptionString, CtsCall ctsCall) at Microsoft.Exchange.Data.Storage.ImapItemConverter.WriteMimePart(ItemToMimeConverter converter, MimeStreamWriter writer, OutboundConversionOptions options, MimePartInfo partInfo, MimeFlags conversionFlags) at Microsoft.Exchange.Data.Storage.ImapItemConverter.GetBody(Stream outStream) at Microsoft.Exchange.Data.Storage.ImapItemConverter.GetBody(Stream outStream, UInt32[] indices) From my reading around it seems that the suggestion is to ask users to log in to Outlook / OWA and view the messages there. However, having logged in as the users myself, the messages cannot be found either through searching or by browsing the folder detailed in the log entry. The server returns the following error to the client: "The message could not be retrieved using the IMAP4 protocol. The message has not been deleted and may be accessible using either Microsoft Outlook or Microsoft Office Outlook Web Access. You can also try contacting the original sender of the message to find out about the contents of the message. Retrieval of this message will be retried when the server is updated with a fix that addresses the problem." Messages were transferred in to Exchange by copying them from the old Apple Xserve, accessed using IMAP. So my question, finally: 1. Is there any way to get the IMAP Exchange connector to rebuild its cache of messages since it doesn't seem to be pulling them directly from the MAPI store? 2. Alternatively, if there is no database, any ideas on why these messages don't appear in Outlook or OWA would be gratefully received. Many thanks, Mike

  Read the article

• graphic error on console

  - by Christian Elsner

  I have Linux on an embedded system. There is no graphic system, but I still have graphic errors. For example, if I type: ifconfig eth2 hw ether 00:0e:8c:d0:59:d2 I see: ifconfig eth hw ether 00:0e:8:2:2 If I type Enter, it accepts the command I typed, so it's just a matter of displaying. Everything is fine, when I log in via SSH. Anyone any ideas, what could be the cause or where to look at? Output of lspci: 00:00.0 Host bridge: Intel Corporation 3100 Chipset Memory I/O Controller Hub 00:00.1 Unassigned class [ff00]: Intel Corporation 3100 DRAM Controller Error Reporting Registers 00:01.0 System peripheral: Intel Corporation 3100 Chipset Enhanced DMA Controller 00:02.0 PCI bridge: Intel Corporation 3100 Chipset PCI Express Port A 00:03.0 PCI bridge: Intel Corporation 3100 Chipset PCI Express Port A1 00:1c.0 PCI bridge: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 1 (rev 01) 00:1c.1 PCI bridge: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 2 (rev 01) 00:1d.0 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #2 (rev 01) 00:1d.7 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset EHCI USB2 Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c9) 00:1f.0 ISA bridge: Intel Corporation 631xESB/632xESB/3100 Chipset LPC Interface Controller (rev 01) 00:1f.2 IDE interface: Intel Corporation 631xESB/632xESB/3100 Chipset SATA IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation 631xESB/632xESB/3100 Chipset SMBus Controller (rev 01) 02:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection 03:01.0 Network controller: Siemens Nixdorf AG Device 4003 (rev 02) 03:01.1 Unassigned class [ff00]: Siemens Nixdorf AG Device 4003 (rev 02) 03:02.0 Ethernet controller: Siemens Nixdorf AG Device 4047 (rev 01) 03:03.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller 03:04.0 Unassigned class [ff00]: Siemens Nixdorf AG Device 4057 (rev 01) 04:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) 05:00.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 44) 06:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) 07:00.0 VGA compatible controller: Silicon Motion, Inc. SM720 Lynx3DM (rev c1) 07:01.0 USB Controller: NEC Corporation USB (rev 43) 07:01.1 USB Controller: NEC Corporation USB (rev 43) 07:01.2 USB Controller: NEC Corporation USB 2.0 (rev 04) The whole thing is running on an Intel Core 2 Duo U2500

  Read the article

• What is good usage scenario for Rackspace Cloud Files CDN (powered by AKAMAI) [closed]

  - by Andrew Smith

  I have just setup my website as static page via Rackspace CDN / Akamai. www.example.co.uk is an alias for d9771e6f24423091aebc-345678991111238fabcdef6114258d0e1.r61.cf3.rackcdn.com. d9771e6f24423091aebc-345678991111238fabcdef6114258d0e1.r61.cf3.rackcdn.com is an alias for a61.rackcdn.com. a61.rackcdn.com is an alias for a61.rackcdn.com.mdc.edgesuite.net. a61.rackcdn.com.mdc.edgesuite.net is an alias for a63.dscg10.akamai.net. a63.dscg10.akamai.net has address 63.166.98.41 a63.dscg10.akamai.net has address 63.166.98.40 a63.dscg10.akamai.net has IPv6 address 2001:428:4c02::cda8:ecb9 a63.dscg10.akamai.net has IPv6 address 2001:428:4c02::cda8:ed09 The HTTP header: HTTP/1.0 200 OK Last-Modified: Fri, 19 Oct 2012 23:27:41 GMT ETag: fdf9e14b77def799e09e8ce815a521da X-Timestamp: 1350689261.23382 Content-Type: text/html X-Trans-Id: tx457979be3bd746c2b4e5403a1189cdbc Cache-Control: public, max-age=900 Expires: Sat, 27 Oct 2012 22:18:56 GMT Date: Sat, 27 Oct 2012 22:03:56 GMT Content-Length: 7124 Connection: keep-alive I am wondering, if it's really the fastest solution to power the website? By investigating it thru http://www.just-ping.com/ it seems, that from many places the ping is very high, and during quick investigation I found that they use GeoIP to resolve addresses based on WHOIS, which is not accurate and because of that from many places the ping is above 300ms (for example, if ISP is in balgladore and request is routed to bangladore even if it's 300ms, for period of 1 month), while by just using Amazon Web Services and Route 53 Anycast DNS servers and only 4 EC2 instances it seems that for example India is always below 100ms, while using Akamai it goes above 300ms in some cases, and this is because Route 53 is using BGP. By quickly checking the Akamai, it seems that they are not getting feedback from the traffic - the high ping stays constant even if I keep downloading large files and videos, which is opposite to what they say on their website. They state, that they optimize the performance by taking feedback from the requests, while it seems they just use GeoIP with per City resolution (which are mostly big cities). Because of this, AWS with Route 53 / Anycast DNS seems to be much more reliable, as well EdgeCast which is using BGP, but I dont know how much does it cost to deploy static website. Actually, I dont know if EdgeCast is not a lie, because from isolated places there are many errors - so their performance is at the cost of quality of delivery, because of BGP switching the routes during transfer of large files. So I was wondering, what is really Akamai good for, because they dont seem to pose any strength in any field in what I do understand now, except they offer some software based WAF on their website, but what I really care about is the core distribiution, so the question is? Is really Akamai good for Videos? For static websites? ??? I found so far AWS most usable with most consistent ping and stable transfers.

  Read the article

• Ubuntu and Postfix Configuration Issues

  - by Obi Hill

  I recently installed postfix on Ubuntu Natty. I'm having a problem with the configuration. Firstly here is my postfix configuration file: # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. mydomain = $myorigin myhostname = mail.nairanode.com alias_maps = hash:/etc/postfix/aliases alias_database = hash:/etc/postfix/aliases # this specifies where the virtual mailbox folders will be located virtual_mailbox_base = /var/spool/mail/virtual # this specifies where the virtual mailbox folders will be located virtual_mailbox_base = /var/spool/mail/virtual # this is for the mailbox location for each user virtual_mailbox_maps = mysql:/etc/postfix/mysql_mailbox.cf # and this is for aliases virtual_alias_maps = mysql:/etc/postfix/mysql_alias.cf # and this is for domain lookups virtual_mailbox_domains = mysql:/etc/postfix/mysql_domains.cf # this is how to connect to the domains (all virtual, but the option is there) # not used yet # transport_maps = mysql:/etc/postfix/mysql_transport.cf virtual_uid_maps = static:5000 virtual_gid_maps = static:5000 mydestination = $myorigin, $myhostname, localhost.localdomain, , localhost relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all #mynetworks_style = host # ADDITIONAL unknown_local_recipient_reject_code = 550 maximal_queue_lifetime = 7d minimal_backoff_time = 1000s maximal_backoff_time = 8000s smtp_helo_timeout = 60s smtpd_recipient_limit = 16 smtpd_soft_error_limit = 3 smtpd_hard_error_limit = 12 # Requirements for the HELO statement smtpd_helo_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_hostname, reject_invalid_hostname, permit # Requirements for the sender details smtpd_sender_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_sender, reject_unknown_sender_domain, reject_unauth_$ # Requirements for the connecting server smtpd_client_restrictions = reject_rbl_client sbl.spamhaus.org, reject_rbl_client blackholes.easynet.nl, reject_rbl_client dnsbl.n$ # Requirement for the recipient address smtpd_recipient_restrictions = reject_unauth_pipelining, permit_mynetworks, reject_non_fqdn_recipient, reject_unknown_recipient_do$ # require proper helo at connections smtpd_helo_required = yes # waste spammers time before rejecting them smtpd_delay_reject = yes disable_vrfy_command = yes Here is also my /etc/postfix/aliases: # See man 5 aliases for format postmaster: root Here is also my /etc/mailname: nairanode.com I've also updated my hostname to nairanode.com However, when I run postalias /etc/postfix/aliases I get the following : postalias: warning: valid_hostname: invalid character 47(decimal): /etc/mailname postalias: fatal: file /etc/postfix/main.cf: parameter mydomain: bad parameter value: /etc/mailname Is there something I'm doing wrong?! I noticed that when I replace myorigin = /etc/mailname with myorigin = nairanode.com in my postfix config, I don't see any errors anymore after calling postalias. Is this a bug or something?!

  Read the article

• SQL Server 2008 - Error starting service - model.mdf not found?!

  - by alex

  my SQL server 2008 was running fine. About an hour ago, it suddenly stopped - the MSSQLSERVER service had stopped I right clicked, clicked start, and it said the service had started, and stopped I looked in the event log and saw these two errors: 17207 : udopen: Operating system error 3(error not found) during the creation/opening of physical device C:\Program Files\Microsoft SQL Server\MSSQL\data\model.mdf. 17204 : FCB::Open failed: Could not open device C:\Program Files\Microsoft SQL Server\MSSQL\data\model.mdf for virtual device number (VDN) 1. The model.mdf db has NEVER been in that location - i specified drive F: to use for data / log during install. I checked the SQL Configuration Manager, to try and set startup params, but SQL Server is not listed as one of the services..... EDIT: I've now moved the db to where it was looking for: C:\Program Files\Microsoft SQL Server\MSSQL\data\ directory. Now if I start the service, it still does not work - i get this error message in the log: Could not find row in sysindexes for database ID 3, object ID 1, index ID 1. Run DBCC CHECKTABLE on sysindexes. Interestingly, i checked the error log - around the time users reported problems, there is this: 2010-01-08 17:11:26.44 spid51 Configuration option 'show advanced options' changed from 0 to 1. Run the RECONFIGURE statement to install. 2010-01-08 17:11:26.44 spid51 FILESTREAM: effective level = 0, configured level = 0, file system access share name = 'MSSQLSERVER'. 2010-01-08 17:11:26.44 spid51 Configuration option 'Agent XPs' changed from 1 to 0. Run the RECONFIGURE statement to install. 2010-01-08 17:11:26.44 spid51 FILESTREAM: effective level = 0, configured level = 0, file system access share name = 'MSSQLSERVER'. 2010-01-08 17:11:26.44 spid51 Configuration option 'show advanced options' changed from 1 to 0. Run the RECONFIGURE statement to install. 2010-01-08 17:11:26.44 spid51 FILESTREAM: effective level = 0, configured level = 0, file system access share name = 'MSSQLSERVER'. 2010-01-08 17:11:44.89 spid10s Service Broker manager has shut down. 2010-01-08 17:11:47.83 spid7s SQL Server is terminating in response to a 'stop' request from Service Control Manager. This is an informational message only. No user action is required. 2010-01-08 17:11:47.83 spid7s SQL Trace was stopped due to server shutdown. Trace ID = '1'. This is an informational message only; no user action is required.

  Read the article

• DPM 2010 PowerShell Script to Easily Restore Multiple Files

  - by bmccleary

  I’ve got what I thought would be a simple task with Data Protection Manager 2010 that is turning out to be quite frustrating. I have a file server on one server and it is the only server in a protection group. This file server is the repository for a document management application which stores the files according to the data within a SQL database. Sometimes users inadvertently delete files from within our application and we need to restore them. We have all the information needed to restore the files to include the file name, the folder that the file was stored in and the exact date that the file was deleted. It is easy for me to restore the file from within the DPM console since we have a recovery point created every day, I simply go to the day before the delete, browse to the proper folder and restore the file. The problem is that using the DPM console, the cumbersome wizard requires about 20 mouse clicks to restore a single file and it takes 2-4 minutes to get through all the windows. This becomes very irritating when a client needs 100’s of files restored… it takes all day of redundant mouse clicks to restore the files. Therefore, I want to use a PowerShell script (and I’m a novice at PowerShell) to automate this process. I want to be able to create a script that I pass in a file name, a folder, a recovery point date (and a protection group/server name if needed) and simply have the file restored back to its original location with some sort of success/failure notification. I thought it was a simple basic task of a backup solution, but I am having a heck of a time finding the right code. I have seen the sample code at http://social.technet.microsoft.com/wiki/contents/articles/how-to-use-a-windows-powershell-script-to-recover-an-item-in-data-protection-manager.aspx that I have tried to follow, but it doesn’t accomplish what I really want to do (it’s too simplistic) and there are errors in the sample code. Therefore, I would like to get some help writing a script to restore these files. An example of the known values to restore the data are: DPM Server: BACKUP01 Protection Group: Document Repository Data Protected Server: FILER01 File Path: R:\DocumentRepository\ToBackup\ClientName\Repository\2010\07\24\filename.pdf Date Deleted: 8/2/2010 (last recovery point = 8/1/2010) Bonus Points: If you can help me not only create this script, but also show me how to automate by providing a text file with the above information that the PowerShell script loops through, or even better, is able to query our SQL server for the needed data, then I would be more than willing to pay for this development.

  Read the article

• Thinkpad speaker turns mute - Linux Codec issue?

  - by Curlew

  At some point a few days ago the speakers on my Lenovo Thinkpad T410 (Model number: 2537A11) suddenly stopped working randomly. This error happens every time I watch a video or listen to a music file. The sound just abruptly stops. At the moment, I can't produce a single sound no matter what I do. I am using Debian GNU/Linux on this laptop and there doesn't appear to be anything else wrong (the fan is working, no abnormal heat (staying around ~40°C), no other obvious errors or problems). Here is the output of a nice program someone pointed me to: martin@martin:~/Downloads$ sudo python run.py --monitor Using temporary directory: /dev/shm/hda-analyzer You may remove this directory when finished or if you like to download the most recent copy of hda-analyzer tool. Downloading file hda_analyzer.py Downloading file hda_guilib.py Downloading file hda_codec.py Downloading file hda_proc.py Downloading file hda_graph.py Downloading file hda_mixer.py Downloaded all files, executing hda_analyzer.py Watching 1 cards ====================================== Sound is working normally and then it stops and the following lines appear: Diff for codec 0/0 (0x14f15069): --- +++ @@ -164,17 +164,17 @@ Power: setting=D0, actual=D0 Node 0x1f [Pin Complex] wcaps 0x400501: Stereo Pincap 0x00000010: OUT Pin Default 0x901701f0: [Fixed] Speaker at Int N/A Conn = Analog, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT - Power: setting=D0, actual=D0 + Power: setting=D3, actual=D3 Connection: 2 0x10* 0x11 Node 0x20 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE And now there is also an error in the dmesg output hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj. I changed the bdl_pos_adj to various numbers (-1, 0, 64, 1024) and either there is no change at all or dmesg reports that the adjustment is too big. I wonder if this bdl_pos_adj is the real reason for the error. Here is my hardware information provided by alsa-info.sh website. Okay, i did some serious testing and even installed Windows and now i officially conclude that this is a hard-ware related issue with my Laptop speakers. Reason: The error occurs in my installed Debian Linux, an Ubuntu Live distribution and Windows XP No error-message appears in all of the OS. The sound just keeps running and i can't hear a thing. I tested different setups, including OSS, ALSA and the pulseaudio server on top If i use my new usb-headphones i can hear sound all the time without any sudden silences. So obviously, although hard to believe, my laptop speakers are not okay (never heard of similar cases). I'll award the bounty to anyone who can point me to good tutorials or the procedure how to exchange my T410 speakers (i still have warranty. The laptop was bought in Germany, but now i am in Denmark). Or to someone who can explain me the output from hda-analyzer (big log above).

  Read the article

• Localhost has just stopped working (using xampp)

  - by Joe Taylor

  I installed Xampp to use for local development of a Drupal site. Its been working fine out of the box until now. The main Xampp localhost welcome menu loads, however my subdirectory (localhost/drupal) doesn't. It just spins in the browser for ages and nothing happens. Just a blank screen. I've tried the edit people suggest in the hosts file but that hasn't work and I'm getting no errors so not sure what to do. Anyone have any ideas what might be wrong? PS I'm running Windows 7 edit: Log files: Fatal error: Allowed memory size of 134217728 bytes exhausted (tried to allocate 123731968 bytes) in C:\xampp\apps\drupal\htdocs\sites\all\themes\directory\node--job.tpl.php on line 41 Fatal error: Allowed memory size of 134217728 bytes exhausted (tried to allocate 123731968 bytes) in C:\xampp\apps\drupal\htdocs\sites\all\themes\directory\node--job.tpl.php on line 41 [Tue Nov 05 20:52:07.242454 2013] [ssl:warn] [pid 8432:tid 260] AH01909: RSA certificate configured for www.example.com:443 does NOT include an ID which matches the server name [Tue Nov 05 20:52:07.331459 2013] [core:warn] [pid 8432:tid 260] AH00098: pid file C:/xampp/apache/logs/httpd.pid overwritten -- Unclean shutdown of previous Apache run? [Tue Nov 05 20:52:07.820487 2013] [ssl:warn] [pid 8432:tid 260] AH01909: RSA certificate configured for www.example.com:443 does NOT include an ID which matches the server name [Tue Nov 05 20:52:07.898492 2013] [mpm_winnt:notice] [pid 8432:tid 260] AH00455: Apache/2.4.4 (Win32) OpenSSL/0.9.8y PHP/5.4.16 configured -- resuming normal operations [Tue Nov 05 20:52:07.898492 2013] [mpm_winnt:notice] [pid 8432:tid 260] AH00456: Server built: Feb 23 2013 13:07:34 [Tue Nov 05 20:52:07.898492 2013] [core:notice] [pid 8432:tid 260] AH00094: Command line: 'c:\xampp\apache\bin\httpd.exe -d C:/xampp/apache' [Tue Nov 05 20:52:07.905492 2013] [mpm_winnt:notice] [pid 8432:tid 260] AH00418: Parent: Created child process 7588 [Tue Nov 05 20:52:08.882548 2013] [ssl:warn] [pid 7588:tid 272] AH01909: RSA certificate configured for www.example.com:443 does NOT include an ID which matches the server name [Tue Nov 05 20:52:09.467582 2013] [ssl:warn] [pid 7588:tid 272] AH01909: RSA certificate configured for www.example.com:443 does NOT include an ID which matches the server name [Tue Nov 05 20:52:09.534585 2013] [mpm_winnt:notice] [pid 7588:tid 272] AH00354: Child: Starting 150 worker threads. Fatal error: Allowed memory size of 134217728 bytes exhausted (tried to allocate 123731968 bytes) in C:\xampp\apps\drupal\htdocs\sites\all\themes\directory\node--job.tpl.php on line 41 Fatal error: Allowed memory size of 134217728 bytes exhausted (tried to allocate 123731968 bytes) in C:\xampp\apps\drupal\htdocs\sites\all\themes\directory\node--job.tpl.php on line 41

  Read the article

• 10.6.4 Apple Wiki: New just created users can do nothing?

  - by beefon

  Hello, After update to 10.6.4 there's an issue: any new users that I create in Server Prefs/WGM can't post to their blogs, comment, create wiki pages... They can't do anything! There's log from Wiki errors (when user DURAK tries to create new blog entry): [HTTPChannel,5,127.0.0.1] Traceback (most recent call last): [HTTPChannel,5,127.0.0.1] File "/usr/share/caldavd/lib/python/twisted/web/server.py", line 126, in process self.render(resrc) [HTTPChannel,5,127.0.0.1] File "/usr/share/caldavd/lib/python/twisted/web/server.py", line 133, in render body = resrc.render(self) [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_xmlrpc_server/WebAppServer.py", line 90, in render d = defer.maybeDeferred(function, *args) [HTTPChannel,5,127.0.0.1] File "/usr/share/caldavd/lib/python/twisted/internet/defer.py", line 104, in maybeDeferred result = f(*args, **kw) [HTTPChannel,5,127.0.0.1] --- <exception caught here> --- [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_xmlrpc_server/ContentServiceBase.py", line 121, in xmlrpc_addEntry aPage = ContentEntry.newBundleBasedContentEntry (path = path, content = content, author = author, title = title, uid = uid, type = kind, versioned = self.versioned, templateName = template) [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_wlt/ContentEntry.py", line 794, in newBundleBasedContentEntry aPage.save('First created', 'created') [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_wlt/ContentEntry.py", line 445, in save revisions.addRevision(self.serializeEntry(revisionAttributes), inComment = comment, inAuthor = updateAuthor, inChangeType = editType) [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_utilities/sqlitersion.py", line 36, in _func result = f(self, *args, **kwargs) [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_utilities/sqlitersion.py", line 49, in addRevision contentPlistStr = plistlib.writePlistToString(inContentDict).decode("utf-8") [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 110, in writePlistToString [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 94, in writePlist [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 251, in writeValue [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 280, in writeDict [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 238, in writeValue [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 171, in simpleElement [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 221, in _escapeAndEncode [HTTPChannel,5,127.0.0.1] exceptions.UnicodeDecodeError: 'ascii' codec can't decode byte 0xd0 in position 0: ordinal not in range(128) [HTTPChannel,5,127.0.0.1] 'Unparseable html in page, removing whatever was already written.' [HTTPChannel,5,127.0.0.1] Removing /Library/Collaboration/Users/durak/weblog/27133.page Any "old" user CAN create, modify, comment, etc. What can you recommend to fix this issue? Hope for your help...

  Read the article

< Previous Page | 464 465 466 467 468 469 470 471 472 473 474 475  | Next Page >