Search Results

Search found 2516 results on 101 pages for 'gigabit ethernet'.

Page 47/101 | < Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54 | Next Page >

debian 6 losing a large amount of packets

- by Sc0rian

I have a rather strange problem. We covered all the obvious hardware related issues (different nic, eth cable and switch) however I cannot seem to stop eth dropping packets. I have 4 servers all exactly the same. driver: e1000e version: 1.2.20-k2 firmware-version: 1.8-0 bus-info: 0000:06:00.0 They are all running the latest kernel(2.6.32-5-amd64). However they do this: RX packets:17073870634 errors:0 dropped:14147208 overruns:0 frame:0 another server: eth0 Link encap:Ethernet HWaddr e0:69:95:05:2f:cb inet addr:10.10.10.86 Bcast:10.10.10.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5455209277 errors:0 dropped:375445 overruns:0 frame:0 TX packets:3666134366 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6688414486673 (6.0 TiB) TX bytes:1611812171539 (1.4 TiB) Interrupt:20 Memory:d0600000-d0620000 eth1 Link encap:Ethernet HWaddr 00:1b:21:b7:7a:ce inet addr:10.10.0.86 Bcast:10.10.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15473695728 errors:0 dropped:5808325 overruns:0 frame:0 TX packets:20112364421 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9192378766434 (8.3 TiB) TX bytes:20216368266761 (18.3 TiB) Interrupt:17 Memory:d0280000-d02a0000 A massive amount of dropped packets. I have tried to load on the latest driver, 1.9.5. This did nothing. I'm not sure what else to do.

Read the article
ssh from 1 ubuntu box to another ubuntu box

- by michael

Hi, I have 2 ubuntu boxes in a WiFi network. Below is the 'ifconfig' of my destination machine. But in my source machine, I tried 'ssh 192.168.1.2' I get connection refused. $ ifconfig eth0 Link encap:Ethernet HWaddr c8:0a:a9:4d:d6:6a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:35 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4508 errors:0 dropped:0 overruns:0 frame:0 TX packets:4508 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:330441 (330.4 KB) TX bytes:330441 (330.4 KB) wlan0 Link encap:Ethernet HWaddr 00:23:14:32:e8:dc inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::223:14ff:fe32:e8dc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:319828 errors:0 dropped:0 overruns:0 frame:0 TX packets:618371 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:30642011 (30.6 MB) TX bytes:921522542 (921.5 MB) How to set up so that I can ssh from 1 box to another?

Read the article
vmware player won't run on CentOS due to missing /dev/vmmon, what could be the problem?

- by Graphics Noob

So I've tried installing vmware player 3.1.4 and 3.1.3 and both times had the same problem, when I try to load a VM I get the error "Could not open /dev/vmmon". When I ls /dev/ I can see there is no "vmmon" device present. When I try running: sudo /etc/init.d/vmware start I get the output: Starting VMware services: VMware USB Arbitrator [ OK ] Virtual machine monitor [FAILED] Virtual machine communication interface [ OK ] VM communication interface socket family [ OK ] Blocking file system [ OK ] Virtual ethernet [FAILED] which shows that the Virtual Machine Monitor fails to load. I tried following the advice on this site and ran vmware-modconfig --console --install-all I notice during the compilation there are no errors, but at the end I get the message: Starting VMware services: VMware USB Arbitrator [ OK ] Virtual machine monitor [FAILED] Virtual machine communication interface [ OK ] VM communication interface socket family [ OK ] Blocking file system [ OK ] Virtual ethernet [ OK ] Unable to start services Out of curiousity I tried: sudo /sbin/insmod /lib/modules/2.6.18-238.9.1.el5xen/misc/vmmod.ko But got the error message: insmod: error inserting 'vmmon.ko': -1 Invalid module format I have a feeling this may be the root of the problem, but I don't know what could be causing it or how to fix it.

Read the article
Broad Band LAN connection through existing 6 wire phone line ( no phone connected )

- by Paul Taylor

I have an (up to but never achieved ) 10 mb broadband signal coming into my house along the telephone line. The modem then connects the broadband signal via a LAN connection and Wi-Fi signal to my computers and iPad. My workshop desk is 54 yards (approx. 50m) downhill from the modem (part of a separate building) – too far to give a good direct signal. The inside corner of the workshop (by a window) receives a weak signal. I have a disconnected telephone cable consisting of 6 wires going from the house to the workshop. The telephone is no longer used in the workshop - we use our mobile number for business calls. A broad band signal using the cable would not have to share with a phone. What would be the most economic price/efficient way to get the broadband signal to the workshop? I am writing in hope that since the telephone didn't need the six wires, an Ethernet connection might be similar and not need all the eight wires for a LAN connection. In theory could use the telephone wire to pull an Ethernet cable trough the underground pipe but I doubt if the cable would survive the strain. The broad band connection in the workshop does not have to have network facility. My skill level is high enough to do house wiring, plumbing and gas fitting; so given any sound advice and a wiring diagram or instructions I can probably work out the rest myself.

Read the article
Two hosts on same subnet can't see each other

- by Joey Hewitt

I've got two routers with two separate public IP addresses on the same subnet, but I can't get them to talk to each other. Both are connected to the internet (ISP-provided gateway) via Ethernet ports provided by the landlord, but I don't have access to or knowledge of how those are physically connected or the protocols used to get back to the ISP. I can ping either from the outside, but they can't ping each other. Traceroutes in and out look the same, and they receive the same gateway over DHCP. I can ping other IPs on the subnet, so I assume this is not any sort of intentional isolation for security/privacy. Since I'm in a setup where my landlord provides internet and we don't have contact with the ISP, I can't really ask the ISP for help (doubt the landlord would know much either.) The situation is similar to the diagram at this question, but instead of the two servers, there's another router coming off the (presumed) switch, and I don't have access to the switch. I've tried giving them static routes to each other with the ISP internet gateway as the gateway, but that's not working. One is a Linksys WRT54GL running DD-WRT, the other is a Netgear WGR614v7, although I could get something more capable if necessary. I'd like to keep them each connected directly to the ISP on their WAN ports, but I can have an ethernet cable between them if necessary - I'm wondering if there's a way without that, and if there isn't, I'd appreciate advice on how to get that working. Sorry this is so nitpicky; there are reasons for all the constraints, but they don't apply to the real question, so I left them out. ;) Thank you!

Read the article
How can I redirect/forward all the UDP/TCP traffic on one interface to another interface in OpenWrt

- by Sina Sou

I am new to networking and I have a measurement device (D) that periodically sends all its readings over few UDP multicast sockets (with different multicast IP addresses and different port numbers). That device even listens to a TCP socket simultaneously to modify its configuration on port 7234. Since the device has just a Ethernet interface for communication and I want to make it work wireless, I decided to use a very small wireless open-wrt based router that attaches to the device (D) and redirect/forward all the network traffic(Both UDP/TCP) to the router wireless interface. In order to simplify the problem assume that the Device (D) establishes following sockets (at the same time) UM_SOCK1: UDP mcast socket on 239.1.2.3 port# 50620 UM_SOCK2: UDP mcast socket on 239.1.2.4 port# 50640 TC_SOCK3: TCP DHCP/STATIC ip address 192.168.1.200 port 7234 And (D) is connected to Open-Wrt router (R) via interface en01 (Ethernet) the router has it own wireless interface on (wlan0) I want all the traffic from interface pass through wlan01 and vice versa (bi-directional) en01 <---- wlan01 What would be the minimum iptables or ... commands that I need to make this possible? Even I am wondering if traffic directing can be made easier like if the direction is not going to be based on IP addresses(not desired if the device is connected via DHCP) I would rather redirection to be Interface(en0) based or on MAC address (The best solution since my device has unique MAC address)? Thanks

Read the article
How to configure network on Windows Server 2008

- by Gokhan Ozturk

I have a IBM x3400 Server Machine with Windows Server 2008 R2 installed on it. But, since I am not expert on networking I have some problems. These roles installed on my server: Active Directory DNS File Sharing Hyper-V ISS VPN There is two network card on them. I configured them like this: Local Connection 1: 192.168.30.3 255.255.255.0 192.168.30.2 127.0.0.1 Local Connection 2: 192.168.30.101 255.255.255.0 192.168.30.6 127.0.0.1 My problem is, when I use this Ip gateways, It is sharing internet to all computers. This is not I want. I want to use Local Connection 1 for internal network. I am giving all computers gateway and DNS IP as 192.168.30.3 The Local Connection 2 is for Hyper-V and VPN connections. 192.168.30.2 and 192.168.30.6 are my modem's gateways. I am using 192.168.30.6 external IP for VPN connections. There is two 24 port switches. There is a connection between them and this two ethernet card connected directly to them. And modems are connected to switches as well (Morems are not near the server. They are somewhere in the building). I disabled network Bridge and removed all ethernet cards from it. With this configuration, all computers can ping my server's IP (192.168.30.3) but on server I cannot ping any clients (Request timeout). What is the best way to configure my network? Thank you. Redgards

Read the article
Router vs switch in a LAN [closed]

- by servernewbie

If I have a LAN and and connect it with a switch, I understand it uses a CAM table to route packets in layer 2 (by saving mac to port relations). So far all good. However, when using a router for a LAN (ONLY for a LAN, not to connect it to "the outside" WAN/internet/etc) I get a bit confused as to how it internally processes packets. I would first split this into two router scenarios: Router with buit-in switch In this scenario, I would expect that it will act exactly as a switch with a CAM table internally. This would probably benefit a bit in speed (guessing here?) compared to the next option. Router without built-in switch Here is where I get confused. If hostA wants to send a packet to hostB, it will ARP to find hostB's MAC address and send it there. Now, if we had a switch (above scenario) this would be easy. But how does it work now in a router WITHOUT a switch? If I would guess, hostA would send an Ethernet frame with hostB's MAC address to the line. The router would fetch the packet (even though the router has another MAC address, it would still fetch this packet even if it only contains hostB's MAC address). It would strip the Ethernet frame header and check the IP, and then check its own internal ARP table again for the MAC address. Now, this would seem like a waste of resources compared to a router with a built-in switch. But maybe it does not work like that at all. Does it also contain a CAM table? If that would be true, what would then the difference between these two routers really be?

Read the article
Setting up /etc/network/interface file for KVM ubuntu 10.10

- by Charles Thornton

I am trying to setup KVM on Unbuntu 10.10 IFCONFIG DUMP: hydra(~}$ifconfig eth0 Link encap:Ethernet HWaddr 00:1b:fc:cb:77:eb inet addr:172.20.20.3 Bcast:172.20.20.255 Mask:255.255.255.0 inet6 addr: fe80::21b:fcff:fecb:77eb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1345 errors:0 dropped:0 overruns:0 frame:0 TX packets:1541 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:820414 (820.4 KB) TX bytes:317708 (317.7 KB) Interrupt:23 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) virbr0 Link encap:Ethernet HWaddr 0a:1e:fb:b4:77:84 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 inet6 addr: fe80::81e:fbff:feb4:7784/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:56 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:8934 (8.9 KB) hydra(~}$ QUESTION:: How should /etc/network/interfaces be setup?? The following attempt just kills my internet connection! --------- /etc/network/interfaces ------------- # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 172.20.20.3 netmask 255.255.255.0 network 172.20.20.0 broadcast 172.20.20.255 gateway 172.20.20.1 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off What am I doing wrong????

Read the article
Ubuntu - wireless connection works great but wired is totally dead

- by Dan

I am running Ubuntu 10.04 on my Acer Aspire One netbook. The wireless connection works great, but the wired is totally dead. When I plug the Ethernet wire, the little led next to the port doesn't blink. If I do ifconfig, this is the output: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1659 errors:0 dropped:0 overruns:0 frame:0 TX packets:1659 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:132304 (132.3 KB) TX bytes:132304 (132.3 KB) wlan0 Link encap:Ethernet HWaddr 18:f4:6a:65:48:1f inet addr:192.168.1.7 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::1af4:6aff:fe65:481f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:94823 errors:0 dropped:0 overruns:0 frame:0 TX packets:81390 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:93028474 (93.0 MB) TX bytes:18002558 (18.0 MB) There is no eth0. Is that normal? In the "Network Connections" GUI there is an entry "Wired connection 1", its "MAC address" field is blank. How can I make the wired connection work?

Read the article
Route web traffic through a separate iterface

- by tkane

I'd like to route web traffic through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

Read the article
"Network is unreachable" When pinging google, can connect to internal computers on debian VM

- by musher

Similar to this SU question: "Network is unreachable" when attempting to ping google, but internal addresses work Actually, it's pretty much the same base issue. I went through that thread trying to find a solution, I changed my resolv.conf: before: domain [my work domain] search [my work domain] nameserver [my gateway] nameserver [my gateway2] I changed it to: after: domain [my work domain] search [my work domain] nameserver 8.8.8.8 nameserver 8.8.4.4 However, any time I reboot the computer the resolv.conf gets overwritten to the previous version (the 'before' above). The issues began after I installed virtualbox additions, X server and (specifically) LXDE: Cat of apt history.log: Start-Date: 2014-08-21 10:03:42 Commandline: apt-get install virtualbox-guest-utils virtualbox-guest-dkms Install: x11-xkb-utils:amd64 (7.7+1, automatic), libxaw7:amd64 (1.0.12-2, automatic), xfonts-utils:$ End-Date: 2014-08-21 10:03:56 Start-Date: 2014-08-21 10:18:39 Commandline: apt-get install lxde Install: desktop-base:amd64 (7.0.3, automatic), libgoa-1.0-0b:amd64 (3.12.4-1, automatic), lxmenu-d$ End-Date: 2014-08-21 10:21:52 Start-Date: 2014-08-21 10:26:40 Commandline: apt-get upgrade Upgrade: libio-socket-ssl-perl:am ifconfig on the guest: root@Peridot:~# ifconfig eth0 Link encap:Ethernet HWaddr 08:00:27:89:c9:20 og inet addr:172.31.2.102 Bcast:172.31.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe89:c920/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2281 errors:0 dropped:1 overruns:0 frame:0 TX packets:463 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:266507 (260.2 KiB) TX bytes:120554 (117.7 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240 (240.0 B) TX bytes:240 (240.0 B) The adapter in VBox is a bridged adapter directly onto my ethernet connection; as are my other 2 VMs (which work) Other SU questions I've tried: "connect: Network is unreachable" in VirtualBox VM

Read the article
Route web browsing through a separate iterface

- by tkane

I'd like to route web browsing through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

Read the article
Wireless driver activation issue in Compaq c700 in Ubuntu 9.04

- by Fazil

I am using Ubuntu 9.04, I cant access my wireless driver, I activate the madwifi in administrationhardware drivers, but I could'nt activated the wireless too. when I type lspci I get the following message, ################################################## # 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 04) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 04) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 04) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 04) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f4) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 04) 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01) 02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) ################################################## but when I tried in Windows I found that the driver for my laptop is ################################################ atheros AR5007 802.11b/g WiFi Adapter ################################################ so what can I do for solving this problem.

Read the article
Windows 7 using llt for ipv6

- by Seoman

The question asked below is based on the specific implementations of the Os not the RFC. Looking on a way to be able to assign a fixed ip address to a host, before it boots I found that Centos 6 works fine with no modifications and Windows 7 does not work at all. As defined in enter link description here exists 3 valid ways of generate a DUID: 1 Link-layer address plus time 2 Vendor-assigned unique ID based on Enterprise Number 3 Link-layer address Looking at the centos, that works fine, I can see the following autogenerated DUID: option dhcp6.client-id 0:1:0:1:19:60:25:f1:52:54:0:6b:b9:9e; and the MAC address for this host is: ifconfig eth1 | grep HWaddr eth1 Link encap:Ethernet HWaddr 52:54:00:6B:B9:9E As you can see, the DUID containts the MAC address. I can assign a fixed ip address to this host by including an entry on my dhcp server similar to: host vm { hardware ethernet 52:54:00:6B:B9:9E; fixed-address6 2001:db8:0:1::200; if packet(0,1) = 1 { log(debug,"VM Request match!"); } } And the Centos 6 gets his ip. On the windows side, I faced a common problem explained on this other link enter link description here As summary, Win7 uses the option 2 of the DUID generation or a variation of this one. On the link explains how to move it to a llt (link layer + time) but is not working fine. If I modify the DUID to one that looks like the one generated on Centos (but with the right MAC) it works as expected. Question 1 How Can I change the DUID generation for Windows 7 to be based on MAC as Centos 6 does? Thanks

Read the article
Windows 7 / TCP/IP network share guide - looking for to resolve failure to mount lacie network drive but works on XP,Linux,Mac.

- by Rob

Can anyone advise me of a really good, readable, Windows 7 TCP/IP network share guide, book, or reference. I want this because I cannot mount my Lacie 2big ethernet network drive in Windows 7 (32 bit home), but I can mount it in Windows XP Home 32bit, Ubuntu Linux 10.04 and Apple MacOS X. This drive is being mounted via the accompanying Lacie Ethernet Agent in XP (which I believe uses "Bonjour" protocol), on Mac and Linux it works without further need for software. Another Super User user has the same problem, but no answer: Trouble accessing network drives in Windows 7 I hope my take on the question shows a better willingness to investigate and do some digging - and therefore invite some suggestions to help with this. The drive is detected by Windows 7 (i.e. speech bubble "network drive found") but on trying to open an Explorer window, this remains blank with the Windows busy pointer. I'd prefer not to reinstall Windows 7 to see if that cures the problem, I'd rather understand what is happening/not happening, perhaps even compare differences with Windows XP. Suggestions, please for such guides or even the original problem itself. Update Edit Rewrote question more comprehensively here: Mhttp://superuser.com/questions/304209/looking-for-definitive-answer-to-accessing-a-network-share-via-windows-7-home-and

Read the article
linux networking: how to redirect incoming connections from old server to new server?

- by aliz

hi I'm in the process of moving my old server to a new server, but i will keep the old server running for database replication and load balancing, etc. each server has a separate internet connection with a static ip, and they are connected through a local Ethernet connection. I've got Ubuntu 8.04 32-bit running on old server and Debian 6.0 64-bit on new one. shorewall firewall is installed on both servers. there are some outdoor devices which are periodically sending data to port 43597 for old server IP address. I can run multiple instances of the network service which is responsible for receiving data from devices on a server but on different ports. here's the question: how can I run the service on new server and have connections coming to old server redirected to it, and new devices can still connect to new server's IP address preferably on the same port and same service? until all devices get updated to send to new server. I've tried a shorewall DNAT rule, but seems like new server's default route should be changed to ethernet connection, which breaks other things. I also found about redir utility, but still haven't tried it. is there any best practice or simple solution for such a scenario, i'm not aware of? thanks in advance.

Read the article
Connect USB hard drive to wireless router on RJ45 port? Possible?

- by lawphotog

just a quick story behind. I was trying to set up wireless networked hard drive at home. My wireless router doesn't take USB. I am considering few options. First i was considering to get something like WD My Cloud. My router is an old one provided by service provider. It only has 10/100 Ethernet. WD My Cloud has Gigabit interface. So unless i changed a new router, data transfer will be slow. So upgrading the router is a must if i want fast transfer speed. Plus I already own an external hard drive with USB 3.0 interface. So if I get a router like Netgear D6300, i can get a decent speed wireless shared drive at home. And i can use my existing HDD instead of WD My Cloud. But the router isn't cheap so I am saving up for that. In the meantime I found out the existence of USB to RJ45 adaptor. I read the reviews and some say it works for them and for some don't. They didn't really say what they were trying to do so I'm confused. So if i bought an adaptor like this, can i connect my existing HDD (USB) with my existing router (RJ45) and use it as a shared drive for data transfer? I know it will be slow as the adaptor will only have USB 2.0 and 10/100 for Ethernet. But it's fine as it's for temporary until i got my new router.

Read the article
vmware player won't run on CentOS due to missing /dev/vmmon, what could be the problem?

- by Graphics Noob

So I've tried installing vmware player 3.1.4 and 3.1.3 and both times had the same problem, when I try to load a VM I get the error "Could not open /dev/vmmon". When I ls /dev/ I can see there is no "vmmon" device present. When I try running: sudo /etc/init.d/vmware start I get the output: Starting VMware services: VMware USB Arbitrator [ OK ] Virtual machine monitor [FAILED] Virtual machine communication interface [ OK ] VM communication interface socket family [ OK ] Blocking file system [ OK ] Virtual ethernet [FAILED] which shows that the Virtual Machine Monitor fails to load. I tried following the advice on this site and ran vmware-modconfig --console --install-all I notice during the compilation there are no errors, but at the end I get the message: Starting VMware services: VMware USB Arbitrator [ OK ] Virtual machine monitor [FAILED] Virtual machine communication interface [ OK ] VM communication interface socket family [ OK ] Blocking file system [ OK ] Virtual ethernet [ OK ] Unable to start services Out of curiousity I tried: sudo /sbin/insmod /lib/modules/2.6.18-238.9.1.el5xen/misc/vmmod.ko But got the error message: insmod: error inserting 'vmmon.ko': -1 Invalid module format I have a feeling this may be the root of the problem, but I don't know what could be causing it or how to fix it.

Read the article
No outbound internet connection after restarting CentOS 6.3

- by wnstnsmth

After restarting a headless CentOS 6.3 machine, it lost outbound internet connectivity, i.e. I can still connect to the server via SSH (ssh root@**.126.18.56), but stuff such as ping google.com gives google.com: unknown host, and yum list some_package gives a lot of network errors. This is what ifconfig gives: eth0 Link encap:Ethernet HWaddr 00:25:90:78:2D:5D inet addr:**.126.18.56 Bcast:**.126.18.255 Mask:255.255.255.0 inet6 addr: fe80::225:90ff:fe78:2d5d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:75594 errors:0 dropped:0 overruns:0 frame:0 TX packets:787 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7074741 (6.7 MiB) TX bytes:144391 (141.0 KiB) Interrupt:20 Memory:f7a00000-f7a20000 eth1 Link encap:Ethernet HWaddr 00:25:90:78:2D:5C UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:16 Memory:f7900000-f7920000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:6 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:504 (504.0 b) TX bytes:504 (504.0 b) I have absolutely no clue how to debug this, and I find it very strange since I can still connect via ssh. EDIT: Weirdly, /etc/resolv.conf does not contain any entries, or none that I can make sense of: # Generated by NetworkManager search sui-inter.net # No nameservers found; try putting DNS servers into your # ifcfg files in /etc/sysconfig/network-scripts like so: # # DNS1=xxx.xxx.xxx.xxx # DNS2=xxx.xxx.xxx.xxx # DOMAIN=lab.foo.com bar.foo.com So is it possible that rebooting the server erased that file? It worked before at least! And how do I solve this? By the way, pinging an IP address works.

Read the article
Is it possible to command a common router without using the web interface?

- by MDeSchaepmeester

Some background The internet arrangement in my student home is really weird. There is one ethernet outlet and several wifi hotspots. Either way requires a login through a web site to get internet access. This is annoying as each device needs to login seperately and with a PS3 for example, it is impossible to get connected at all since the web login procedure doesn't work. Therefore I have installed a D-Link DIR-635 router which is connected to the ethernet outlet. It has DHCP enabled so it uses NAT, but whatever it is connected to also uses NAT and I've read this should not work. A fellow student tried it with an Apple Airport but that keeps giving errors related to NAT after NAT. Anyway my setup does work so bonus points if you can clarify this. I need to login to the web site I mentioned earlier with any device, after which all devices in my LAN have connectivity. This is great. Except... In short From time to time, I lose internet connectivity and my D-Link DIR-635 router needs to do a DHCP renew. I can do this via the web interface but my life would be easier if I could just run a cmd file which tells my router to do this without all the hassle. This would setup a connection to my router and execute the proper command. I have tried googling but couldn't find much helpful stuff.

Read the article
How to use non-free drivers during debian install

- by blokeley

I'm trying to install debian stable using unetbootin. The install process fails with "network autoconfiguration failed", probably due to the ethernet driver not working. My Lenovo U350 has a Broadcom BCM57780 which does not seem to be supported out-of-the-box: there are various bug reports here, here and here, but I don't know if the fix has made it into debian (6) stable. One discussion says that you have to use an ethernet driver from the firmware-linux-nonfree package. I'm not sure that this is correct because the BCM57780 is not in the list of drivers in firmware-linux-nonfree. The specific question tree is: Is BCM57780 supported in debian stable? If so, what could be wrong? Should I install debian unstable instead? If not, do I need to use firmware-linux-nonfree during installation and, if so, how do I do this? Please note: I've used ubuntu and debian loads in the past but please post line-by-line guidance rather than some cryptic abbreviation of any instructions. Thanks in advance for any help. Updates: Debian stable with non-free drivers did not work. Debian unstable (free drivers only) did not work. Tried loading firmware-iwlwifi_0.28_all.deb from another USB stick to get wireless working rather than BCM57780. The .deb file was found but the network configuration still failed! That's it, I'm giving up. Unfortunately I'll use ubuntu even though the Unity user interface will be very unstable for the next couple of years :(

Read the article
VirtualBox bridged network not working as expected

- by iby chenko

I am having hard time getting Bridged network to work with VirtualBox. Idea is to have host as well as one or more guests on same LAN. Using NAT (default) I do get access to internet and any node on the LAN when working from one of the VM guests. However, no LAN node including host can access (or ping) guest in VM. I need to be able to use any guest as if it was a physical computer on the network (need to be accessed by any machine on LAN). According to my understanding of the VirtualBox documentation, this should be Bridged mode. I think I set it correctly, well, actually there is not much to it: 1. select Bridged mode in VM network setup 2. select physical NIC of the host to connect bridge to 3. start VM When I do this, each VM does get new IP address that corresponds to LAN settings : 192.168.1.100 192.168.1.102 192.168.1.103 etc. where host is 192.168.1.80 / 255.255.255.0 (IP addresses above 100 are served by DHCP server). This seem to be correct based on what I know about ethernet. From VM I can ping other nodes like 192.168.1.50 etc. and I still get ethernet access. So far so good... But I STILL cannot ping any of the other VMs (running ones of course). I cannot ping them from other VMs, from host or from other nodes on the LAN. Aside from fact that IP addresses handed to guests are now local, this still acts same as NAT. What is going on? What am I missing? Regards, I

Read the article
Set up layer 2 vlan between 2 data centres

- by user41679

Hello, Our data centre provider operates 2 sites, and we currently have equipment in one and would like to have equipment in the second. They've told me that they operate a layer 2 vlan between the 2 sites over a 20gbit connection, and that they'd just give me ethernet cable at each end to connect the locations. At the current site, we have Cisco 2960 48TC-L switches, all the machines are on a 192.168.x.x subnet and we have cisco firewalls with which we connect to our internet provider with. My question is what would I need to do to connect the 2 sites? could I just plug the ethernet cables the provide into the cisco switches, and have the same switches the other end? would I need to set up a separate internal network on the other side and connect both through the firewalls? Would the cisco switches need special configuration? We expect to maintain a number of connections between the 2 sites, and each site would have its own internal dns name like dc1.xx.com. Sorry if I'm being vague or haven't included enough information, I've a fairly good knowledge of hardware but we're down a netops guy at the moment and I'd like to get both sites on-line ASAP! Thanks in advance!

Read the article
New at TRC: Networking Products

- by uwes

The new category "Networking Products" has been added last week at Oracle Hardware Technical Resource Center (HW TRC). The following list summarize the different areas which are included. Feel free to explore. Oracle Virtual Networking customer and technical presentation, Datasheets, partner FAQ and more 10 GbE Network Adapters and Switches customer and technical presentations, Datasheets, partner FAQ, Documentation and more Gigabit Ethernet customer presentations, partner FAQ, Documentation and more InfiniBand Datasheets, partner FAQ and Documentation Blade Server Network Express Modules (NEMs) technical presentation, Datasheets, partner FAQ, White Paper and more Storage Networking customer presentations, Datasheets, partner FAQ and more Please be aware that you need to be registered at the Oracel HW TRC. To register click here ... and follow the instructions..

Read the article

< Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54 | Next Page >