Search Results

Search found 34056 results on 1363 pages for 'mod access'.

Page 471/1363 | < Previous Page | 467 468 469 470 471 472 473 474 475 476 477 478  | Next Page >

• Setup IPv6 over IPv4 tunnel in VPN

  - by bfmeb

  Let me explain my szenario: I have a linux server A. A is reachable in a VPN. So if I am connected to the VPN over Internet I can successfully ping A. Server A is connected to a Router B. Router B has a local ipv6 address and there are resources (each of them with a local ipv6 address) connected to Router B. After I am connected to VPN, I am able to use ssh to have access over A. Now I can use the ping6 command to ping the Router B or one of its connected resources. This works fine. The ping fails if I try to ping router B on my computer. Overview: My Computer -- VPN -- Server A(ipv4) -- Router B(ipv6) -- Ressource A(ipv6) On resource A runs for example a HTTP-Server. My question is: How can I access Resource A (for example with HTTP) on my to VPN connected computer? Is it possible? Should I setup a tunnel device? Sorry for this inexpertly explanation, but I am new to network stuff!

  Read the article

• Nginx flv audio pseudo stream works but video is not loading

  - by sarah

  I am working on a development server for a company & they want nginx webserver to work with. So the requirements for their company is, it should be capable of doing following things i.e hotlink protection, mp4 & flv pseudo stream & secure streaming. However nginx fulfills their requirements and i am configuring their server from past 2 days as i am new to this field so i've only acheived hotlinking prevention in past 2 days. But the problem on which i am stuck is flv pseudo streaming, to make work to mp4 pseudo stream it was just a piece of paper but i am really fuc*ed up with flv pseudo stream. I have converted my flv videos with flvmdi tools to insert many keyframes but the problem is , when i try to seek video from following keyframes that are generated by flvmdi i.e test.flv?start=2681223, video does not load but audio pseudo works fine. So it means no problem with my flv configuration in nginx.conf file. And the forum that i used to compile my nginx-1.2.1 is http://h264.code-shop.com/trac/wiki/Mod-H264-Streaming-Nginx-Version2 & by adding additional module --with-http_flv_module. This forum is really active, hopes i will resolve my problem as soon as you guys will provide me some guide.

  Read the article

• One vs. many domain user accounts in a server farm

  - by mjustin

  We are in a migration process of a group of related computers (Intranet servers, SQL, application servers of one application) to a new domain. In the past we used one domain user account for every computer (web1, web2, appserver1, appserver2, sql1, sqlbackup ...) to access central Windows resources like network shares. Every computer also has a local user account with the same name. I am not sure if this is necessary, or if it would be easier to configure and maintain to use one domain user account. Are there key advantages / disadvantages of having one single user account vs. dedicated accounts per computer for this group of background servers? If I am not wrong, one advantage besides easier administration of the user account could be that moving installed applications and services around between the computers does not require a check of the access rights anymore. (Except where IP addresses or ports are used)

  Read the article

• Can you link to a good MySQL dumper PHP script?

  - by Ivan

  I need to migrate a website to another host. I have only FTP server access and MySQL name+pass (the MySQL server's IP I was provided is 127.0.0.1, and there's neither PhpMyAdmin nor SSHell to use). A web app run there can access the DB using credentials I know and localhost server. So I'd need a PHP script, that will correctly dump all the available databases of the MySQL server so that they can be imported on the new server. Can you recommend a good one?

  Read the article

• export block device over network without root

  - by dschatz

  I'm trying to export a file as a block device over the network. I do not have root access on the machine where the file exists. I do have root access on the machine(s) where I will mount the block device. I've seen ATA-Over-Ethernet and ISCSI but there don't seem to be any implementations which allow me to export the block without root at least (some even require kernel modules). Is there an implementation of either of these or some other protocol that doesn't require root? Perhaps I can tunnel ethernet over IP to do this?

  Read the article

• Joining a network with a Virtual Windows Server 2008 R2

  - by Triztian

  Hi all, here's my case, I have set up a share in a virtual windows server 2008 R2, the server is hosted by GoDaddy my question is, how do I access the server's public folders, I need to open a file locally (on the client) and to do that I need the server to show up in my Network locations, I have the right credentials and have created a special group that has access to the particular folder that I'm sharing the problem is I don't know how to add the server to my network locations. I have tried VPN Connection but it is my understanding that it cannot be done since it is virtual share server. Any help is trully appreciated.

  Read the article

• Mac firewall blocking nginx (port 80) from external side

  - by Alex Ionescu

  I installed nginx using ports and started it with sudo. Accessing the nginx welcome page from localhost works perfectly, however accessing it from an external computer fails. Doing an nmap on the computer from the outside reveals 80/tcp filtered http So clearly the mac firewall is blocking the port. I then proceed to add the nginx executable to the firewall exception list as seen in this image, however the nmap still shows up as port 80 being filtered and I'm unable to access the webpage. The exact binary that is in the list is /opt/local/sbin/nginx which to my knowledge seems correct Any ideas what I should do? Thanks! P.S. Turning the firewall off does allow me to access the website from the outside world, however that isn't an ideal solution.

  Read the article

• I bought a domain name at GoDaddy and hosting at Dreamhost but the first doesn't work!

  - by janooChen

  I added the Dreamhost's nameservers like 12 hours ago to: I entered to the following panel: Nameservers -> Set Nameservers (I have specific nameservers for my domains) and added Dreamhost's nameservers liek this: Nameserver 1: NS1.DREAMHOST.COM Nameserver 2: NS2.DREAMHOST.COM Nameserver 3: NS3.DREAMHOST.COM So now in the admin panel I see this: Nameservers Nameservers: (Last Update 2/10/2011) NS1.DREAMHOST.COM NS2.DREAMHOST.COM NS3.DREAMHOST.COM But I get this when I run the analysis tools: Attention Required! There are critical issues Accessing Your Web Site Accessing Your Web Site Properly configuring your domain name and hosting account ensures that visitors can access your site. Did I do something wrong or I have to wait 24 to 48 hours? (Dreamhost does display my page because I can access the other domain name I bought together with the hosting) (By the way, if everyone uses the same nameserver, how will go GoDaddy know which is the hosting space that I purchased among all others)? Thanks in advance.

  Read the article

• Install Trac Without Setting Up a VirtualHost in Apache?

  - by jobu1324

  I'm trying to set up Trac to test out it's functionality, and the only guides I can find online talk about setting up a VirtualHost. Right now I am under the impression that I need access to a DNS server to properly use the VirtualHost directive, and for various reasons I don't have access to one. Is it possible to set up Trac without setting up a VirtualHost? I haven't had any luck. If I run the site with tracd, it works - which means that at least part of it is set up properly. Right now all I have is an Apache Directory directive pointing to /pathToTracSite/htdocs/, and when I visit the trac location, all I get when viewing the site from a browser is an empty directory (which makes sense, because htdocs/ is empty). My server is running Apache2 I know I'm missing a lot here, because I don't understand Apache the Trac system very well - any help would be appreciated.

  Read the article

• How can I join two simple home networks together using an ethernet cable?

  - by Ilia Jerebtsov

  I want to join two different home networks together like so: PC A1 PC A2 PC B1 PC B2 \ / \ / Gateway A <----- ethr. cable -----> Gateway B | | ADSL modem A ADSL modem B Both networks are of the basic residential type with identical configuration, with all PCs running Vista/7. The point is to temporarily join two apartments in a building for gaming and file sharing, and the holy grail would be: PCs on network A can access PCs on network B and vice-versa (file shares and gaming). Each network uses its own internet connection. Data between networks shouldn't take a trip through the internet (broadband upload speeds are severely capped) A network's internet access should continue working if the joining cable is disconnected with minimal configuration changes. How closely can this be achieved?

  Read the article

• .htaccess deny from all does not work?

  - by jeffery_the_wind

  I am running Apache 2.2.20 on a Ubuntu 11.04 web server. I have a Joomla site running on it, but I have also added some custom content. In the main web directly I have added a folder /images/sub_folder and in this sub_folder I have put a bunch of pictures. I do not want anyone to be able to simply access these pictures directly from the web, so I made a .htaccess file in that sub_folder and just put the following line in it: deny from all There doesn't seem to be any effect, I can still access the images directly from a web browser. I have restarted the Apache service. What am I doing wrong? Thanks Tim

  Read the article

• How to use 2 or more internet connections on the same network?

  - by Rogue

  Living in a joint family we have 3 internet connections, each floor has one internet connection which is split per floor. Each internet connection is shared between 4-5 computers using a switch per floor. Each of these internet sharing networks are independent of each other. What I want to achieve here is a local network (for local messenger and file sharing) that can combine all the 3 independent networks, problem is that whenever I try to do that the whole network tends to use just one internet connection. I have all the necessary hardware. How do I solve this problem, one approach could be that I could get one PC to act as a server and bridge the internet connections and then the whole network would have to access the internet through this server. Theoretically this could be possible but I have never tried this approach in real life. Also if certain computers need be restricted from internet access how would this be possible on the same network?

  Read the article

• configure HTTPS server on a cisco router

  - by Sara

  For the past week I was trying to configure an HTTPS server on a cisco 2900 router, I've used the following commands and assigned a username and password to privilege 15 however, when Im trying to access a given ip it requires a username and password however when I insert the username and password I configured it does not allow me to enter and i'm not sure where the problem is. Router(config)# ip http secure-server Router(config)# ip http authentication local These were the commands i used for the https server and also I used the following to assign the username and password Router(config)#username name privilege 15 secret 0 password where 'name' and 'password' represent the username and password respectively I'm trying to access the 192.168.14.1 interface on the router and the username and password i created are not authorized to enter (I got the commands from a cisco router manual)

  Read the article

• How to install Gitlab in a VM on a production server?

  - by Michaël Perrin

  I have a production server running Ubuntu 12.04 and I would like to install on it a VM with Gitlab (using Vagrant and Virtualbox). Let's say that the address to access Gitlab is gitlab.mydomain.com . The DNS zone has been configured to point to the IP address of the server. I want users to be able to access to Gitlab (either for pushing to a repository, or for accessing to the web interface) from the outside. The VM has been configured to have an IP address. It means that when browsing http://gitlab.mydomain.com for instance, the request has to be forwarded to the VM on the server, ie. to the VM IP address. What are the ways to configure this? Can Apache be used as a proxy? In this case, I guess it only works for HTTP requests, but not for pushing to a Git repository on the VM.

  Read the article

• some keyboard keys not working properly

  - by surfmadpig

  I'm using windows 7. All of a sudden, a couple of hours ago, this happened: My keyboard number keys [above the letters] stopped working properly, both as numbers and as symbols. Only 5 and 6 are functional. Also, I've noticed that the End key isn't working either, and perhaps a couple more from that group. I'm pretty sure it has something to do with those evil Sticky Keys/Filter Keys/ whatever those ease of access things are, BUT I've turned off all the ease of access keyboard options and nothing has changed. Is it possible that something is still turned on while I unchecked it? Are the on/off checkboxes to control WHEN it happens or IF it happens? I also tried rebooting and uninstalling/reinstalling keyboard from device manager, to no avail. It's certainly a software issue and not a hardware issue, as I've tried another keyboard and the problem persists. And, predictably enough, it's annoying. Any ideas?

  Read the article

• Preferred apache permissions for www files with several authors

  - by user1316464

  I can't for the life of me figure out how to design my permissions scheme for my apache files. My requirements seem pretty simple: Apache should have standard permissions of RX for Directories and R for files Web authors should have RWX for Directories and RW for files Don't want to give any access to "other" Want new files/folders to inherit the proper permissions Here are the schemes I've tried 570 for directories and 460 for files Owner: Apache Group: Webdev The problem here is that new files created by users int the Webdev group are owned by user:Webdev and Apache can't read them. If Apache were in the group Webdev then it would also have the wrong permissions (ie it would have Write permissions to files) 750 for directories and 640 for files Owner: Webdev Group: Apache (Webdev is a member of Apache) The problem here is that there is only one webdev account and I have multiple people who need access to contribute. In theory this would work with only one developer if Webdev were also a member of the Apache group. Any ideas?

  Read the article

• windows 2008 R2 TS printer security - can't take owership

  - by Ian

  I have a Windows 2008 R2 server with Terminal server role installed. I'm seeing a problem with an ordinary user who is member of local printer operators group on the server. If the user opens a cmd window using ‘run as administrator’ they can run printmanager.msc without needing to enter their password again. In printmanager they can change the ownership of redirected (easy print) printers without problems. If, from the same cmd window, they use subinacl to try and change the onwership of the queue to themselves they get access denied: >subinacl.exe /printer "_#MyPrinter (2 redirected)" /setowner="MyDom\MyUsr" Elapsed Time: 00 00:00:00 Done: 1, Modified 0, Failed 1, Syntax errors 0 Last Done : _#MyPrinter (2 redirected) Last Failed: _#MyPrinter (2 redirected) - OpenPrinter Error : 5 Access denied so, same context, same action but one works and one doesn't. Any ideas for this odd behaviour? I'm using subinacl x86 on an x64 server as I can't find anything more up to date. I've tried with icacls and others but couldn't get them to do anything with printers.

  Read the article

• Is there a way to force/manage file locking in windows?

  - by JPbuntu

  I have a 2 Windows machines networked and I am having trouble with simultaneous access to files. I would like only one user to be able to open a file at a time, which I thought was automatic, using file locks.... if the program used to access the file is locking the file. I believe the problem I am having is some of the programs I use, don't lock the file, and there for can be modified simultaneously by multiple users, which is very much not desired. Currently I am having this problem with only two computers, although as soon as I can figure out a solution to this problem the network is going to be expanded to 6 computers, which will include Windows 7, Vista, and XP, as well as a central file server (Samba). Is there a way to ensure that all files opened in windows get locked? Any suggestions are appreciated, thanks.

  Read the article

• How to protect Ruby on Rails code on external server?

  - by Phil Byobu

  I have to deploy a Ruby on Rails Applications on a client's server and I do not want them to be able to view or modify the source code. How would you protect the code technically? I thought about building a linux-based virtual machine with an encrypted filesystem where the application code resides. The client has no root access, or direct access to the system at all. All services start automatically and the application is ready to use. What would you suggest?

  Read the article

• What is a good php 5.3.x shared hosting company?

  - by Abba Bryant

  I am looking for the best shared host - features-wise, not price - for hosting CakePHP and Lithium applications. I would like to be able to use MongoDB / MySQL as well as have access to some of the more common PHP extensions like MCrypt, etc. I currently use dreamhost with a custom PHP 5.3.x build on my sandbox domain - Please do not suggest this as a solution. I want to move away from managing my own PHP build if possible. I need ssh access but email support isn't as big of an issue.

  Read the article

• Drive stopped working on windows server 2003 and I receive a "controller error"

  - by Durden81

  I can access the server in safe mode. I have a Proliant 360 Hp server with Windows server 2003 R2. The event viewer is completely filled up with this error: the driver detected a controller error on Device\Harddisk3\DR3 I individuated the drive affected. It is drive H that is a secondary non mirrored drive. When I access anything on that drive I receive: "the request could not be performed because of an I/O device error" What should I do? Is this just a driver issue or a hard drive failure? Please give me a quick help as my websites are offline due to this. Any suggestion is welcome!

  Read the article

• VPN/Proxy server to bypass work proxy

  - by Trevor

  Here is my dilema, I am at work and can not set up a VPN connection to my VPN account in the USA. So what I would like to do is somehow have my "IE" at work connect to my home network and route any internet requests through my home PC to my VPN account, so I can access my USA Contents? So what I was thinking and I am not sure if this will work, but set up a proxy server at home on my home computer, that then routes all requests to my VPN Tunnel to the USA. Have my work computer use my home computer as the proxy and viola I have unrestricted internet access? Does that sound feasable? Thanks.

  Read the article

• Use teamviewer for running web server [closed]

  - by Steve

  I have a PC behind NAT. I want to host a web server on it which is accessible from the internet. I cannot open any blocked ports nor do i have admin rights on the computer. But it has a teamviewer client running on it 24*7 to which i do have access(no vpn installed). I can accesss this client from anywhere using teamviewer. I want to know if somehow i can use teamviewer to get a ip/hostname that is accessible from the internet and host a webserver. Also is it possible to get an ip if i get admin access but without opening ports.

  Read the article

• Prevent folder deletes at top level only on Server 2008

  - by DomoDomo

  I'm trying to prevent folders moves, really folder delete in NTFS parlance, for series of folders within a network share. So let's say I have: FolderA, FolderB, FolderC. Each folder has various files and subfolders. I want the Domain Users group to have modify access to all files and folders beneath FolderA, FolderB, and FolderC. However I don't want them to be able to delete these three top level folders. The issue we are having right now is people keep accidentally dragging one top level folder into another. I've tried used advanced NTFS permissions to deny domain users delete access to these top level folders, and set the permissions to apply to "This folder only", however it seems to only affect sub-folders, and not the top level. Platform is Server 2008 Standard. Thanks in advance.

  Read the article

• Why my webservice not live on internet? [closed]

  - by blankon91

  I've windows server that goes live on internet, (e.g. www.mysite.com). Then I want to create another site with different port (e.g. www.mysite.com:502). I've create that and it works when I access it on local network, but when I access it from outside of local network (internet) the www.mysite.com:502 can't accessed but the www.mysite.com can accessed. what should I do to make www.mysite.com:502 goes online? I use windows server 2008 standard

  Read the article

< Previous Page | 467 468 469 470 471 472 473 474 475 476 477 478  | Next Page >