Search Results

Search found 15651 results on 627 pages for 'setup'.

Page 476/627 | < Previous Page | 472 473 474 475 476 477 478 479 480 481 482 483  | Next Page >

• Solaris 10: cannot ping to/from server

  - by anurag kohli

  All, I have a Solaris 10 server which is not reachable by IP (ie can't ping to/from the server). I believe I have the default route setup correctly. See below: # ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 192.168.62.100 netmask ffffff00 broadcast 192.168.62.255 ether 0:14:4f:b1:9b:30 # netstat -rn Routing Table: IPv4 Destination Gateway Flags Ref Use Interface -------------------- -------------------- ----- ----- ------ --------- 192.168.62.0 192.168.62.100 U 1 40 bge0 224.0.0.0 192.168.62.100 U 1 0 bge0 default 192.168.62.1 UG 1 0 127.0.0.1 127.0.0.1 UH 1 4 lo0 # # cat /etc/defaultrouter 192.168.62.1 I have verified layer1 and layer 2 are up on the switchport, and that it's on the correct VLAN. I have also checked the default gateawy (192.168.62.1) is in fact reachable since I can ping it from my PC: Pinging 192.168.62.1 with 32 bytes of data: Reply from 192.168.62.1: bytes=32 time=1ms TTL=254 Reply from 192.168.62.1: bytes=32 time=1ms TTL=254 Reply from 192.168.62.1: bytes=32 time=3ms TTL=254 Reply from 192.168.62.1: bytes=32 time=6ms TTL=254 I'm at a loss as to what is wrong. I would highly appreciated your assistance. Thank you very much.

  Read the article

• SSH traffic over openvpn connection freezes when I cat a file

  - by user42055

  I have an openvpn (version 2.1_rc15 at both ends) connection setup between two gentoo boxes using shared keys. it works fine for the most part. I use mysql, http, ftp, scp over the vpn with no problems. But when I ssh from the client to the server over the vpn, weird things happen. I can login, i can execute some commands. But if i try to run an ncurses application like top, or i try to cat a file, the connection will stall and I'll have to sever the ssh session. I can, for example, execute "echo blah; echo .; echo blah" and it will output the three lines of text over the ssh session fine. But if i execute "cat /etc/motd" the session will freeze the moment I press enter. I compiled openvpn 2.1.1 on my mac and copied over my config directory from my gentoo client. The mac connected and ssh sessions worked fine without freezing. I then compiled it on my older gentoo box (2.6.26 kernel) which I am retiring due to a dying hard drive, and ssh over it also works perfectly. Why does it fail on my brand new gentoo box ? I've tried compiling three different kernels in case it was that, but other than that there should be no difference between my older and my newer gentoo boxes that I can think of. Any suggestions on what's wrong ?

  Read the article

• Apache is spawning more and more processes!!

  - by erotsppa

  We have a LAMP setup that is working prety good for half a year. All of a sudden today the apache server (mysql servers are not on this box) started to die. It seems to have started to spawn more and more processes over time. Eventually it will consume all the memory and the server would just die. We are using prefork. In the mean time what we are doing is just added more ram and increased the MaxClients and ServerLimit parameter to 512. We're just prolonging the crash. The number still goes up slowly. Maybe in a day, it would reach that limit. What is going on? We only have around 15-20 request per second. We have 1Gb memory and it's not half used, there's no swapping going on. Why is apache creating more and more processes? It's almost like theres a leak somewhere! The database boxes are fine, they are not causing a delay to requests. We tested some queries everything is quick!

  Read the article

• VMWare Workstation Linux Host performance tuning

  - by Hoghweed

  I need to improve my linux hosted vmware workstation for using multiple virtual machines at the same time. I feel very stupid I lost a great blog post link which I found last month (and I'm not able to find it again..) so I try to ask here if anyone can help me: This is my host (laptop): 16GB DDR3 Ram HDD Hybrid 750GB 7200 (8GB SSD Cache) Mint 15 x64 Kernel 3.9.7 swappiness set to 10 The above are the important things about the host. So, My need is the ability to run 2 or 3 VMs at the same time. The lack of performance is about the disk, The last time from that blog post I lost, I setup /tmp to be mounted ad a memory partition and in my previous installation that was good, now I'm not able to find a good solution to tweak the things. I think with 16GB o RAM there will be no problems to run multiple VMs, but whe they start to swap or use the /tmp things going bad (guest cursor going too fast after a freeze, guest freeze and so on) Anyone can help me to fit a good host tweak and configuration to get better performance? Thanks in advance

  Read the article

• How can I fix video tearing and pausing on Windows XP Flash videos?

  - by xvs

  I have what should be a reasonably fast PC: it's a Quadcore Intel 6600 at 2.4 GHz, 4MB of RAM, an ATI 3800 series video card and an LG L246WP monitor, which I selected particularly because it was supposed to work well with video and have no trails or other artifacts. So I should be able to play video with no problems. And I can, as long as that video isn't Flash video. With Flash, what I see is tearing, especially during pans, and pausing -- every few seconds the video pauses for about 300ms while the sound stays continuous. I tried going into the video card setup and changing vertical sync, pulldown detection, windows media video acceleration, deinterlacing and triple buffering. but no combination of settings I've tried has changed or corrected the problem in any way. I've also tried enabling and disabling hardware acceleration in the Flash settings, to no avail. This problem happens whether or not the video is streaming or has fully streamed in before playing. So, what can I do? Is this just a flash issue or is there a way to get it to work?

  Read the article

• Exchange 2007 relay from sendmail, message "Undelivered". Possible reasons?

  - by garlicman

  Note: This is my re-post from Stackoverflow. I've been messing with a test environment for security purposes where a DMZ RHEL5 sendmail server is used as a relay for an Exchange 2007 server. Exchange is working in the environment, I have Vista and XP VMs using Outlook on the Domain to send e-mail to each other. I've been trying to simulate an external internet VM sending an e-mail to the DMZ sendmail relay, which forwards to the Exchange server. Before everyone thinks this is too big a problem/question, I've followed the sendmail/Exchange guides and all I want to know is how I can determine why a relayed message/e-mail in Exchange is "Undelivered". Basically I send a SMTP message to the sendmail server, which relayed to my Exchange. The /var/log/maillog shows the e-mail being relayed to Exchange. Nov 17 13:41:22 externalmailserver sendmail[9017]: pAHIfMuW009017: from=<[email protected]>, size=1233, class=0, nrcpts=1, msgid=<[email protected]>, proto=ESMTP, daemon=MTA, relay=[10.50.50.1] Nov 17 13:42:17 externalmailserver sendmail[9050]: pAHIfMuW009017: to=<[email protected]>, delay=00:00:55, xdelay=00:00:36, mailer=relay, pri=121233, relay=mailserver.xyz.local. [192.168.1.20], dsn=2.0.0, stat=Sent (<[email protected]> Queued mail for delivery) This is good, but the To never receives the e-mail from Exchange. So I started poking around Exchange. In the "Message Tracking" Troubleshooting Assistant I queried the processed messages and found this: (I had to copy and paste the cells... sorry for the format) 2011/11/17 RECEIVE SMTP <[email protected]> "Undelivered Mail Returned to Sender" [email protected] [email protected] 192.168.100.10 MAILSERVER\DMZ Relay [email protected] I just want to know if anyone has any suggestions on why the DMZ Relay Connector I setup isn't relaying and is instead returning the forwarded e-mail to sender as Undelivered? My Exchange Relay Receive Connector is pretty simple. The Exchange server's FQDN is set as the HELO response, all available IP addresses can receive relayed e-mail, and the IP address of my sendmail server is specifically set as a remote server.

  Read the article

• Can grub and BCD work simultaneously?

  - by wuputah

  Here's my setup. After I installed a new SSD, I have: Original Windows 7 on sdc1 (to be retired) Copy of Windows 7 on sdb2 A Windows system partition on sdb1 Ubuntu 12.04 on sda, /boot and ergo grub is on sda1 Grub is MBR on sda and set to boot from BIOS. I prefer to not change this; grub is much preferable as a boot manager. I've run update-grub from Ubuntu and grub seems to be correctly configured as all options are available: I can boot any of the 3 Windows partitions and Ubuntu. I also ran the repair tool to get Windows to add both installations to BCD. At present, choosing particular options seem to have no effect; the old version of Windows on sdc1 always boots. I don't understand what is causing this, but I can't figure out what. How does grub and BCD play along? I can't find any docs on this. My thought was to only boot Windows off sdb1, and then let BCD do the rest (present a menu to boot between sdb2 and sdc1, but I can't seem to get BCD to boot sdb2), but this has been unsuccessful. My configuration files: BCDEdit output grub.cfg

  Read the article

• Squid with mikrotik router

  - by niren

  I tried to connect squid3 in my network to use high anonymity proxy. This is how my network is right now WAN LINK | ------------- ----------------------------- | Mikrotik Box | | Ubuntu Server with squid3 | ------------- ----------------------------- | / | / ---------------------- | Switch ( Cheap one ) | ---------------------- | | | Client1 Client2 Client3 etc. after this setup I changed squid.conf in Ubuntu server as http_port 8080 acl localhost src xxx.xxx.xxx.xxx(Ubuntu server IP) acl to_localhost dst xxx.xxx.xxx.xxx(Mikrotik router gateway) I assume that redirected http from Mikrotik router will be redirect again to Mikrotik router. uncomment access log /var/log/squid3/access.log add visible_hostname myname save squid.conf and restart squid3 server. Then I have added nat rule in Mikrotik router ip/firewall/nat 1. add chain=dstnat src_address=xxx.xxx.xxx.xxx(ununtu server IP) dst-port=80 protocol=tcp action=accept 2. add chain=dstnat src_address=xxx.xxx.xxx.xxx/28(LAN address) dst-port=80 protocol=tcp action=dst-nat to-address=xxx.xxx.xxx.xxx(ununtu server IP) to-port=8080 now I can not able to access internet from client1 system, If I remove these two nat rule then I can access internet. what is wrong I have made?

  Read the article

• Viability of Apache (MPM Worker), FastCGI PHP 4/5.2/5.3, and MySQL 5

  - by Adrian

  My server will be hosting numerous PHP web applications ranging from Joomla, Drupal, and some legacy (read: PHP4) and other custom-built code inherited from clients. This will be a development machine used by a dozen or so web developers and issues like fluctuating loads or particularly high load expectations are not important. Now, my question: are there any concerns I should know about when using Apache w/ MPM Worker, PHP 4/PHP 5.2/PHP 5.3 (all via FastCGI), and MySQL 5 (with a query cache of 64MB)? I have not tested the various applications extensively and I have only recently learned how to install PHP and utilize it via FastCGI (rather than mod_php, which in this case seemed impossible (considering the multiple versions of PHP and the desire to use MPM Worker over MPM Prefork)). I have come to understand that there could be concerns regarding XCache and APC, namely non-thread-safety issues where data becomes corrupted and the capability to use MPM Worker becomes null and void. Is this a valid concern? I have been using my personal testing server (running Ubuntu Server Edition 10.04 in VirtualBox) which has 2GB of RAM available to it. Here is the configuration used (the actual server will likely use a configuration more tailored to suit it's purposes): Apache: Server version: Apache/2.2.14 (Ubuntu) Server built: Apr 13 2010 20:22:19 Server's Module Magic Number: 20051115:23 Server loaded: APR 1.3.8, APR-Util 1.3.9 Compiled using: APR 1.3.8, APR-Util 1.3.9 Architecture: 64-bit Server MPM: Worker threaded: yes (fixed thread count) forked: yes (variable process count) Worker: <IfModule mpm_worker_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 400 MaxRequestsPerChild 2000 </IfModule> PHP ./configure (PHP 4.4.9, PHP 5.2.13, PHP 5.3.2): --enable-bcmath \ --enable-calendar \ --enable-exif \ --enable-ftp \ --enable-mbstring \ --enable-pcntl \ --enable-soap \ --enable-sockets \ --enable-sqlite-utf8 \ --enable-wddx \ --enable-zip \ --enable-fastcgi \ --with-zlib \ --with-gettext \ Apache php-fastcgi-setup.conf FastCgiServer /var/www/cgi-bin/php-cgi-5.3.2 FastCgiServer /var/www/cgi-bin/php-cgi-5.2.13 FastCgiServer /var/www/cgi-bin/php-cgi-4.4.9 ScriptAlias /cgi-bin-php/ /var/www/cgi-bin/

  Read the article

• Simple options for port forwarding to a different port?

  - by Nick

  I have three network printers at our local office, all of which listen on port 9100. Non of them offer the option of changing the listening port. We have a single public static IP address, and access to our main network is through a Linksys WRT-54G. We need to be able to print to these printers from outside the office. The problem is, with the 54G, I can only forward a port to the SAME port on a particular IP address. What I really need though is a way to forward to an ip address and a DIFFERENT port. I need to do this: In port Destination 9100 192.168.1.1 : 9100 9101 192.168.1.2 : 9100 9102 192.168.1.3 : 9100 So I'm looking for options. I could setup an old computer with two network cards and IPtables I suppose, but that seems like a lot of overhead for something relatively simple. Is there a way a virtual machine (read: one network card) could do the advanced port forwarding? Where I forward all traffic to it, and it forwards it on to the right printer? Or what about those mini Linux distros that replace the WRT-54G's firmware? Do any of those support what I need "out of the box"? I have a spare WRT- could I make it an IP tables router? Recommendations for mini distros? Or is there an off-the-shelf product that does this (cheap/local preferred)? Any advice / options appreciated. Thanks!

  Read the article

• Load balancing a Windows File Share using HA-Proxy

  - by NathanE

  After pulling my hair out over DFS I just had this weird and potentially dangerous idea come into my head whereby, just possibly, I might be able to use HA-Proxy to load balance a file share between servers. I've done some remedial packet traces and it does appear that TCP port 445 is the only thing involved in using Windows file sharing. I've always thought for many years that UDP 139, 135 etc were also involved in at least establishing the connection - but apparently not! So I setup a basic test: listen SMBTest *:445 mode tcp server Smb1 172.16.61.201:445 server Smb2 172.16.61.202:445 And you'll never guess what... it works??? (!) Now obviously there is the whole concern about synchronisation between the file servers (of course). That could easily be taken care of with a little bit of Robocopy script. And considering I only need a HA read-only file share there wouldn't be any issues with regard to file locking etc. Can anyone tell me if what I'm playing with here is fire? I really didn't think it would work at all and now I'm a little shocked. What would be the downsides? Could this be relied upon for a production environment?

  Read the article

• sudoer scheme for another web developer that retains my future control of a virtual server?

  - by Tchalvak

  Background: Virtual Private Server I have a virtual private server that I'm looking to host multiple websites on, and provide access to another web developer. I don't care about putting too many constraints on him, though I wouldn't mind isolating the site that he'll be developing from other sites on the server that I will develop. The problem: retain control Mainly what I want is to make sure that I retain control over the server in the future. I want to reserve the ability to create/promote/demote and other administrative functions that don't deal with web software. If I make him an admin, he can sudo su - and become root and remove root control from me, for example. I need him not to be able to: take away other admin permissions change the root password have control over other security/administrative functions I would like him to still be able to: install software (through apt-get) restart apache access mysql configure mysql/apache reboot edit web development configuration type files in /etc/ Other Standard Setups would be happily considered I've never really set up a good sudoers file, so simple example setups would be very useful, even if they're only somewhat similar to the settings that I'm hoping for above. Edit: I have not yet finalized permissions, standard, useful sudo setups are certainly an option, the lists above are more what I'm hoping I can do, I don't know that that setup can be done.

  Read the article

• VirtualBox problems writing to shared folders (Guest Additions installed)

  - by vincent

  I am trying to setup a shared folder from the host (ubuntu 10.10) to mount on a virtualized CentOS 5.5 with Guest Additions (4.0.0) installed (Guest addition features are working ie. seamless mode etc.). I am able to successfully mount the share with: mount -t vboxsf -o rw,exec,uid=48,gid=48 sf_html /var/www/html/ (uid and guid belong to the apache user/group) the only problem is that once mounted and I try to write/create directories and files I get the following: mkdir: cannot create directory `/var/www/html/test': Protocol error I am using the proprietary version of VirtualBox version 4.0.0 r69151. Has anyone had the same problem and been able to fix it or has any idea how to potentially fix this? Another question, the reason for setting this up is this. Our production servers are on CentOS 5.5 however I am a great fan of Ubuntu and would like to develop on Ubuntu rather than CentOS. However in order to stay as close to the production environment I would like to virtualize CentOS to use a web server and use the shared folder as web root. Anyone know whether this isn't a good idea? Has anyone successfully been able to set this up? Thanks guys, your help is always much appreciated and if you need any more information please let me know.

  Read the article

• How to sync two computers using new MobileMe calendar

  - by CesarGon

  I have been using MobileMe for over a year with success. I use it to sync my Outlook calendars in my work and home computers, using Windows 7 and Outlook 2007. The main Outlook calendar folder in my work computer is replicated to MobileMe as "Work", and synced to my home computer, and the main calendar folder in my home computer is replicated to MobileMe as "Home", and synced to my work computer. This means that I can see both "Work" and "Home" calendars from both computers (as well as from the web interface through me.com), which is very convenient. Yesterday I migrated to the new MobileMe calendar, accepting the suggestion that popped up on the me.com website. After the migration, the MobileMe control panel on each of Windows computers asked me to re-configure my calendar setup, and everything fell apart. The "Home" and "Work" calendar folders in Outlook are now ignored by MobileMe, and new ones named "Home in MobileMe" and "Work in MobileMe" have been created, and placed in a separate Outlook data file rather than the default. This means that now: I now have four folders, two of which are not replicated to MobileMe The two folders that are not replicated reside on a separate data file, so alarms and reminders don't work; they're basically useless to me as calendar folders In addition, the button in the MobileMe Control Panel that used to let me specify what MobileMe folder should be synced against the default Outlook folder has gone. MobileMe is now too smart. Do you have any idea how to undo this mess and go back to a situation where I have two folders, as described in the top paragraph, which keep synced? I don't want an extra data file. Thanks.

  Read the article

• Running docker in VPC and accessing container from another VPC machine

  - by Bogdan Gaza

  I'm having issues while running docker in AWS VPC. Here is my setup: I've got two machines running in VPC: 10.0.100.150 10.0.100.151 both having an elastic IPs assigned to them, both running in the same internet enabled subnet. Let's say I'm running a web server that serves static files in a container on the 10.0.100.150 machine the container: IP: 172.17.0.2 port 8111 is forwarded on the 8111 port on the machine. I'm trying to access the static files from my local machine (or another non-VPC machine also tried an EC2 instance not running in the VPC) and it work flawlessly. If I try to access the files from the other machine (10.0.100.151) it hangs. I'm using wget to pull the files. Tried to debug it with tcpdump and ngrep and that I have seen is that the request reaches the container. If I ngrep on the host machine I see the requests going in but no response going back. If I ngrep on the container I see the requests going in and the response going back. I've tried multiple iptables setups (with postrouting enabled, with manually forwarding ports etc) but no success. Help in any way - even debugging directions would be much appreciated. Thanks!

  Read the article

• Incorrect directory permissions with OpenSSH on Cygwin on Windows Server 2008 SP2

  - by Davy Brion

  I ran into a weird directory permission problem when logged in to a Win2008SP2 (not R2) server through SSH. When I open a local cygwin shell on the server, i can do this: myUser@myServer ~ $ cd /cygdrive/c/Windows/System32/inetsrv/ myUser@myServer /cygdrive/c/Windows/System32/inetsrv $ cd config myUser@myServer /cygdrive/c/Windows/System32/inetsrv/config $ I have no issues accessing the 'config' directory when using a local cygwin shell. 'myUser' has all necessary permissions to access the directory as well. In fact, 'myUser' is a local administrator on the machine. Listing the permissions of the config folder through the local cygwin shell shows the following output: 4 drwx------+ 1 SYSTEM SYSTEM 0 Aug 2 09:38 config But when I log into the server with a SSH client (in this case Putty), i run into the following problem: myUser@myServer ~ $ cd /cygdrive/c/Windows/System32/inetsrv/ myUser@myServer /cygdrive/c/Windows/System32/inetsrv $ cd config -bash: cd: config: Permission denied It also doesn't list the proper permissions through SSH: 0 drwxr-x--- 1 ???????? ???????? 0 Aug 2 09:38 config When I look at the running processes on the server with Task Manager (with a remote desktop connection), it shows that all bash.exe processes are running under the 'myUser' account, so I don't understand why I can't access that particular directory through SSH but have no problems accessing it in a local cygwin shell. I'm using OpenSSH 5.9p1-1. I'm not sure what the Cygwin version is... I used the latest setup.exe (version 2.738) of Cygwin, but I can't seem the find any other Cygwin-related version number. I doubt that it's related to SSH/Cygwin though, because when I connect from the Win2008SP2 server to my local Win7 machine through SSH (using the same OpenSSH/Cygwin versions) I can access the /cygdrive/c/Windows/System32/inetsrv/config folder without issues. Does anyone have an idea on what the issue could be?

  Read the article

• VNC on Xen failure

  - by BCable

  The following config works and creates a good VM in Xen: # Kernel Setup kernel = "/boot/vmlinuz-2.6.18.8-xenU" # Memory memory = "256" # Disk disk = [ "file:/opt/xen/domains/110/sda1.img,sda1,w", "file:/opt/xen/domains/110/swap.img,sda2,w" ] # container name name = "110" hostname = "boo" # Networking vif = ["type=ieomu, bridge=xenbr0"] # VNC vnc = 1 #vfb = [ 'type=vnc,vncdisplay=2,vnclisten=0.0.0.0,vncpasswd=110' ] # Behavior Settings root = "/dev/sda1" extra = "fastboot" But when I uncomment the VFB line, I get the following error after it hangs for at least 30 seconds: [root@customer 110]# xm create boo.cfg Using config file "./boo.cfg". Error: Device 0 (vkbd) could not be connected. Hotplug scripts not working. Any ideas? Part two of this question: Sometimes it actually works, and a port is opened. When this happens, nmap shows the VNC ports open and I can connect via the VNC client, but it just hangs at "Connection established." and no VNC display shows up. I've tried multiple VNC clients (TightVNC, TightVNC Java Console, RealVNC), but they all fail to connect. Does VNC through Xen require X to be started in order to function? I was under the impression that it would show the console screen, so I'm confused as to why all these issues are occurring. Thanks!

  Read the article

• nginx error page and internal directives not working as expected

  - by Romain

  I'd like to setup my nginx server to return a specific error page on HTTP 50x status codes, and I'd like this page to be unavailable by a direct request from users (e.g., http//mysite/internalerror). For that, I'm using nginx's internal directive, but I must be missing something, as when I put that directive on my /internalerror location, nginx returns a custom 404 error (which isn't even my own 404 error page) when a page crashes. So, to summarize, here's what seems to happen: GET /Home nginx passes the query to Python I'm simulating an application bug to get the 502 error code nginx tries to return /InternalError from its error_page rule because of the internal rule, it finally fails back to a custom 404 error code <-- why? the documentation says error_page directives are not concerned by internal: http://wiki.nginx.org/HttpCoreModule#internal Here's an extract from nginx.conf with a few comments to point things out: error_page 404 /NotFound; error_page 500 502 503 504 =500 /InternalError; # HTTP 500 Error page declaration location / { try_files /Maintenance.html $uri @pythonbackend; } location @pythonbackend { include uwsgi_params; uwsgi_pass unix:///tmp/uwsgi.sock; } location ~* \.(py|pyc)$ { # This internal location works OK and returns my own 404 error page internal; } location /__Maintenance.html { # This one also works fine internal; } location ~* /internalerror { # This one doesn't work and returns nginx's 404 error page when I trigger an error somewhere on my site internal; } Thanks very much for your help!!

  Read the article

• Migrateing to Windows Server 2008 R2 Domain Controllers - a few Questions/Issues

  - by Chris

  Ok so here's our setup: We have 2 Windows2k3 Domain Controllers. I am trying to replace them with Windows 2008 R2. The Win2k3 servers are DC01 and DC02. The Windows2k8 servers are DC1 and DC2. I prepared the Windows Server 2003 Forest Schema for a Domain Controller That Runs Windows Server 2008 or Windows Server 2008 R2. Then with both of the new servers up as member servers I dcpromo'd DC1 using the advanced option and added it successfully to my exisiting domain. Roles are GC, DNS and Active Directory Domain Services.I transferred The PDC, RID pool manager and Infrastructure master FSMO to the new DC.(DC1) The Schema master and Domain naming master are still on the old DC (DC01). The first issue I'm encountering is when i dcpromo the second DC (DC2) and select "Replicate data over the network from and existing domain controller" I select the new DC to replicate from (DC1) I get the following error: "Failed to identify the requested replica partner (dc1.xxx.org) as a valid domain controller with a machine account for (DC2$). This is likely due to either the machine account not being replicated to this domain controller because of replication latency or the domain controller not advertising the Active Directory Domain Services. Please consider retrying the operation with \dc01.xxx.org as the replica partner. "The server is unwilling to process the request." Is this because the Schema master and Domain naming master roles are still on the old DC (DC01)? And if so, if I transfer Schema master and Domain naming master roles to DC1 what is the risk or breaking my AD? I'm a little paranoid because this process HAS to be transparent. ANY down time or interruption will result in me getting a verbal ass kicking from my I.T. Director. Both of the new servers DNS point the the old DNS servers (DC01 and DC02) not themselves by the way. Thanks in Advance -Chris

  Read the article

• Successful login with iscsiadm on target still doesn't create block device

  - by Halfgaar

  I've set up an experiment to test iscsitarget and initiator, which at some point worked. Later, I turned the setup back on and much to my dismay, the initiator machine stopped making block devices for its successful logins. As far as I know, I haven't changed anything on either machine. Some details: # iscsiadm -m node --login Logging in to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun1, portal: 10.0.0.1,3260] Logging in to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun2, portal: 10.0.0.1,3260] Login to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun1, portal: 10.0.0.1,3260]: successful Login to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun2, portal: 10.0.0.1,3260]: successful Sessions: # iscsiadm -m session tcp: [3] 10.0.0.1:3260,1 iqn.2010-12.nl.ytec.arbiter:arbiter.lun1 tcp: [4] 10.0.0.1:3260,1 iqn.2010-12.nl.ytec.arbiter:arbiter.lun2 Netstat: # netstat -n -p|grep 3260 tcp 0 0 10.0.0.2:48719 10.0.0.1:3260 ESTABLISHED 1078/iscsid tcp 0 0 10.0.0.2:48718 10.0.0.1:3260 ESTABLISHED 1078/iscsid /var/log/syslog doesn't give errors: Jan 27 11:41:49 vmnode001 kernel: [ 378.041749] scsi7 : iSCSI Initiator over TCP/IP Jan 27 11:41:49 vmnode001 kernel: [ 378.044180] scsi8 : iSCSI Initiator over TCP/IP lsscsi doesn't show my devices: [0:0:1:0] cd/dvd TSSTcorp DVD-ROM TS-L333A D100 /dev/sr0 [4:0:0:0] disk ATA Hitachi HUA72105 A74A - [4:0:1:0] disk ATA Hitachi HUA72105 A74A - [4:1:0:0] disk Dell VIRTUAL DISK 1028 /dev/sda And there are no block devices in /dev for it: # ls -1 /dev/sd* /dev/sda /dev/sda1 /dev/sda2 /dev/sda3 /dev/sda4 I tried loading all scsi kernel modules I could find, but that doesn't seem to be the problem. I reall don't get this; it used to work. I found people with similar problems (here and here) but no solution. Initiator is Debian Sqeeuze (testing), target is Debian Lenny (stable). iscsitarget is 0.4.16+svn162-3.1+lenny1, open-iscsi (initiator) is 2.0.871.3-2squeeze1. Target kernel: 2.6.26-2-amd64, initiator kernel: 2.6.32-5-amd64

  Read the article

• Will Intel be releasing anymore 6-core processors soon?

  - by jasondavis

  I am about to start buying parts every week for as long as it takes me to build the best PC I can build. I am looking at the Intel i7-920 processor right now because it is about 250$ and it is a quad-core processor based on the x58 chipset I believe. From what I have read so far, intel is coming out with some 6-core processors soon that will also use the x58 chipset and will allow me to use the same motherboard and memory/ram to upgrade to a 6-core. This sounds really good to me right now. I just read that the new 6-core processor. The Core i7-980X (extreme edition) was just released which is the first 6-core processor but it is supposed to be around $1,000 so I will probably just get the i7-920 for now and then upgrade to the 6-core version when the price goes down. The motherboard I am looking at getting the GIGABYTE GA-X58A-UD5 which is around $280 at newegg.com So that is my basic plan SO far. I have not purchased any parts yet. I am just wanting to ask if this sounds like a good idea or if I should wait longer if I am wanting to eventually have a 6-core processor. Does anyone know if Intel is planning on releasing any other 6-core processor in addition to the Core i7-980X in the near future? I just want to make sure I am buying the best setup for my money if I am going all out on it, thanks for any tips/advice.

  Read the article

• Should I use Evernote or Org-mode for taking notes?

  - by tobeannounced

  I am looking for an app that will help me manage my notes, and after coming across Org-mode, I was wondering whether Org-mode's functionality is strong enough that it can remove the need for me to use another note taking app (because org is more of a task management app), such as Evernote. My wishes for a note taking app are: can be accessed offline in some form, eg through an iPhone app or desktop client Org-Mode and Evernote can both do this, however it seems like MobileOrg is more aimed at tasks, rather than notes? If this is the case, I probably would use Evernote in addition to MobileOrg. I can clip web content into easily for research Evernote has the browser extension, how is it with Org-Mode? I know I can use c-c c-l, but how suited is it really for taking notes on stuff I am browsing in Chrome/Firefox? has voice notes on the iPhone and computer too, if possible Org-Mode cannot do this on the iPhone, on the computer could I record audio externally and then link the files in? I can add notes too on my iPhone & computer while not connected to the internet both can do this. The types of notes I am likely to have include: howtos/things I have learnt, documentation on my setup/stuff, research on things I may do in the future, ideas, and task specific notes. I have thought about where I would want to access each of these notes and will post that here if you think it would help. So, is Org-mode strong enough in note-taking and the requirements I listed that I can avoid the need to use a separate tool for taking notes?

  Read the article

• Force local IP traffic to an external interface

  - by calandoa

  I have a machine with several interfaces that I can configure as I want, for instance: eth1: 192.168.1.1 eth2: 192.168.2.2 I would like to forward all the traffic sent to one of these local addresses through the other interface. For instance, all requests to an iperf, ftp, http server at 192.168.1.1 should be not just routed internally, but forwarded through eth2 (and the external network will take care of re-routing the packet to eth1). I tried and looked at several commands, like iptables, ip route, etc... but nothing worked. The closest behavior I could get was done with: ip route change to 192.168.1.1/24 dev eth2 which send all 192.168.1.x on eth2, except for 192.168.1.1 which is still routed internally. May be I could then do NAT forwarding of all traffic directed to fake 192.168.1.2 on eth1, rerouted to 192.168.1.1 internally? I am actually struggling with iptables, but it is too tough for me. The goal of this setup is to do interface driver testing without using two PCs. I am using Linux, but if you know how to do that with Windows, I'll buy it!

  Read the article

• How to connect to Oracle DB via ODBC

  - by Mat

  I am attempting to connect to a remote Oracle DB via ODBC. I am totally inexperienced and fail to connect. What I have installed: Oracle 'ODBC Driver for RDB' A program I want to connect from (Altova Mapforce, an ETL) What I do: Under Administrative tools I open the Windows "ODBC Data Source Administrator I click 'Add..' and select the Oracle ODBC Driver The Window 'Oracle RDB Driver Setup' opens. I fill in: Data source name: free choice Description: I leave blank Transport: I choose TCP/IP Server: I input the IP address of the server Service: I leave 'generic' UserID: I enter the user name (that belongs to the password I have) Attach Statement: no idea what do do here?? Upon choosing 'OK', the 'Oracle RDB ODBC Driver Connect' opens and I am prompted the password. I enter the password and the connection fails. Questions Do I need further programs on my computer, e.g. the Oracle client of Instant client? I am never prompted the port of the server - isn't this relevant? I am never prompted SID - isn't this relevant? I connected from SQL developer easily - it prompted only server IP, port, username, password and SID.

  Read the article

• SSL Returning Blank Page, No Catalina Errors

  - by Mr.Peabody

  This is my second, maybe third, time configuring SSL with Tomcat. Earlier I had created a self signed, which worked, and now using my signed is proving fruitless. I am using Tomcat, operating from the Amazon Linux API. When using the signed cert/keystore, my server is starting normally without errors. However, when trying to navigate to the domain it is giving me an "ERR_SSL_VERSION_OR_CIPHER_MISMATCH" error. My server.xml file looks as follows: <Connector port="8443" maxHttpHeaderSize="8192" maxThreads="150" minSpareThreads="25" maxSpareThreads="75" enableLookups="false" disableUploadTimeout="true" acceptCount="100" scheme="https" secure="true" SSLEnabled="true" clientAuth="false" sslProtocol="TLS" keystoreFile="/home/ec2-user/.keystore/starchild.jks" keystorePass="d6b5385812252f180b961aa3630df504" /> It couldn't hurt to also mention that I'm using a wildcard certificate. Please let me know if anything looks amiss! EDIT: After looking more into this, I've determined there may be nothing is wrong with the Server.xml, or the listening ports. This is becoming more of an actual certificate error, as the curl request is giving me this error: curl: (35) Unknown SSL protocol error in connection to jira.mywebsite.com:-9824 Though, I can't seem to figure out what the "-9824" is. When comparing this curl to another similar setup (using the same Wildcard Certificate) it's turning up the full handshake, which is to be expected. I believe this is now between the protocol/cypher set default on JIRA servers.

  Read the article

< Previous Page | 472 473 474 475 476 477 478 479 480 481 482 483  | Next Page >