Search Results

Search found 15087 results on 604 pages for 'copy constructor'.

Page 479/604 | < Previous Page | 475 476 477 478 479 480 481 482 483 484 485 486  | Next Page >

• Ubuntu+Win7--disk error press any key to restart

  - by Siddharth

  Apparently,none of the solutions in any other posts and forums worked for me For some reasons I decided to remove ubuntu from my hard disk drive. My partition table(presently): (/dev/sda1) (fat32) 900 MiB ---(MBR,I suppose) (/dev/sda2) (ntfs) 70 GiB -----(Windows 7) (/dev/sda3) (ntfs) 314.88 GiB --(Personal File storage) (/dev/sda4) (ext4) 80 GiB -----(Ubuntu 13.04) (unallocated) -----1.31 MiB So,after moving(cut-paste) everything(for backup) from the fat32 partition using win7..I booted into Ubuntu and copied the remaining 3 files(hidden in Win7 file explorer) --bootmgr,bootsect.bak,and one more which I do not remember.TERRIBLE MISTAKE After this I again booted into Windows and deleted ext4 partition..formatted it to ntfs..and shut down the pc.Then,I put in a Win7 bootable USB..using command prompt I entered bootrec /fixmbr,and bootrec /fixboot.. Restarting showed me the GRUB..choosing windows 7 showed me "Disk Error. Press any key to restart." I also installed a fresh Win7 installation on the 80 GiB partition expecting a Windows Legacy Bootloader with two win7 options..but did not work. Then..I used a Ubuntu LiveUSB to put it back to the present configuration(above) since all methods to restore the MBR failed.. I copied back the fat32 partitions backup files but couldn't copy those 3 files.Somehow ,they had been recreated and were non-replaceable. I do not want to format the win7 partition for a fresh one. I have used boot-repair..Restore MBR option brings back to "Disk error...." without even going through grub..so I reinstalled grub and I'm able to boot into Ubuntu. grub menu shows the win7 option as "Windows 7 (loader) (on /dev/sda1)". paste.ubuntu.com/5753710 paste.ubuntu.com/5775999

  Read the article

• Master does not appear to be a git repository error

  - by EmmyS

  I've inherited a position and instructions for creating a new git repository. Unfortunately I've run into problems and no one here knows what to do. Hoping someone can help me out. Here are the instructions I was left: Create a new repository: For these steps you need to be in the gitosis-admin repository, if you don't have it, in a suitable parent folder do: git clone [email protected]:gitosis-admin.git Edit gitosis.conf file - in gitosis-admin root, under [group base-repo] section, add the name of the new repo to the end of the "writable =" section. Commit change and push back to gitosis-admin master. For the next commands, my_new_project represents the name of your project mkdir my_new_project cd my_new_project git init Copy in any files you want to use to start the repo git commit -a -m "Initializing new repository" git remote add origin [email protected]:my_new_project.git git push master git push master:qa So I did 1 and 2, with no problem. It created a local folder on my machine called gitosis-admin. I edited the gitosis.conf file as indicated. But when I try to do step 3 (which I assume is git push gitosis-admin master) bash tells me that fatal: 'master' does not appear to be a git repository fatal: The remote end hung up unexpectedly What am I doing wrong?

  Read the article

• How to migrate Outlook Express mail rules?

  - by ronwest

  I have a home computer that only had a 15Gb C: drive, and ran out of space with all the Microsoft Updates, etc, that keep coming down. So I fitted a 160Gb drive as a C: drive and altered the drive jumpers to make the old C: drive into a slave D: drive, to save migrating documents, etc. I've installed a clean copy of Windows XP SP3 and reassigned the new Outlook Express' mailstore path to point to the old mailstore folder that now has a D: drive letter - and it all works OK. However, my extensive list of mail rules have not been transferred to the new OE and I have not been able to identify how they are stored. To find it I added a new rule to the new OE, exited OE, then searched on the whole computer (including hidden/system files) for files altered around the time I added the rule. I hoped I could just overwrite a new empty file with an old one. But the only files that seem to be changed are Windows system-level files and some bits and pieces in the Windows\PreFetch sub-folder. None of them can be opened as XP has them locked, and none of them have names that are anything to do with email or rules. Does anyone know of any way of migrating OE rules, or do I have to re-enter them by hand? Thanks!

  Read the article

• Having trouble with a workaround, for booting from a usb stick, using grub and a minimal linux kernel to load usb drivers

  - by s hanley

  I'm trying to boot from a usb stick. I formatted it to fat32, and later to ext2, and installed dsl on it using unetbootin, and later the usb install guide on dsl wiki (http://www.damnsmalllinux.org/wiki/index.php/Install_to_USB_From_within_Linux). The bios doesn't have a setting for booting from usb. Grub doesn't "see" the usb drive when I use the root and find commands, explained in (http://www.damnsmalllinux.org/wiki/index.php/USB_Booting). This happens even when I set boot from floppy at the top of the boot order. However, my usb keyboard is recognised by the bios and by grub. How can it recognise the keyboard but not the usb drive? Also, the usb led does flash even before grub starts up, so surely something must be happening usb-wise? I am now following an ubuntu guide to booting from a USB stick, using a hdd-based, minimal linux kernel to supply the usb drivers. But I'm having difficulty adapting it to other OSes (slax/dsl/aptosid). I believe I have to alter the initrd.gz file to include usb drivers and then copy that file along with vmlinuz to a partition on my hdd. But, what's the grub command for the kernel line supposed to look like? From the ubuntu example it's: title USB FLASH DRIVE root (hd0,6) kernel /boot/usb-boot/vmlinuz file=/cdrom/preseed/ubuntu.seed boot=casper noprompt cdrom-detect/try-usb=true persistent initrd /boot/usb-boot/initrd.lz boot Should mine just be: title USB FLASH DRIVE root (hd0,6) kernel /boot/usb-boot/vmlinuz cdrom-detect/try-usb=true initrd /boot/usb-boot/initrd.lz boot

  Read the article

• Office documents on intranet all requiring second login and can't pass auth? Disable webdav?

  - by DOTang

  I am not sure what is going on, but recently all the Office documents on our intranet get prompted a second time for login and according to the error logs it looks like it's trying to use webdav to open (an editable?) version of the document to save directly on the server? We have no sharepoint server setup or anything, but this shouldn't be happening. All I want is for the document to be saved or opened from a local copy in temp like normal. Here is the log: Line 57499: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 Line 57500: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 Line 57501: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 The log basically contains a bunch of these. How can I disable this behavior so that office documents that are downloaded aren't attempted to be used through webdav?? Edit: I should clarify behavior, it asks if you want to save or open it, upon choosing open open, it asks to re-authenicate, you put in the user information and the login box comes up 3 times acting like you entered the wrong password. For some users, after passing the login box the third time, it still opens up, for others their browser just locks up. It also doesn't even look like webdav is installed on our server, I see no config options in IIS for it as outlined on this page: http://learn.iis.net/page.aspx/350/installing-and-configuring-webdav-on-iis-7/#001

  Read the article

• Windows 7 - SBS - Why does copying a directory not include all subdirectories and files?

  - by indeed005

  Using Windows 7, fully updated... I have had some strange behaviour copying a whole user directory (e.g. "c:\users\bob" to "c:\backups\bob") I understand now that I should have used Easy Transfer or at least robocopy, but at the time all I wanted to do was backup the user's data before using the "Delete account" button. Unfortunately, I didn't check that my copy-paste had actually worked; all it had actually done was copied the appdata subdirectory of the user account. At the time of doing this backup I was logged in as the same user, bob (a local admin) in this example. When I discovered the missing files, I tried again using the domain admin account -- same story. Only appdata copied. No documents folders, nothing else. Then my boss tried, and it worked fine -- it copied all the files. Ctrl+C, Ctrl+V. I tried again... same profile... copied all the files. Same profile, same destination, same rights and permissions, same ownership, but different behaviour. Has anyone encountered this before and come up with a solution? BTW this was not using roaming profiles and the accounts are stored locally.

  Read the article

• Restoring a fresh home folder in a shared user domain environment

  - by Cocoabean

  I am using a tool called pGINA that adds another credential provider to my Windows 7 clients so we can authenticate campus users via campus LDAP. We have the default Windows credential providers setup to authenticate off of our Active Directory, but we have students in our classes that don't have entries in our AD, and we need to know who they are to allow them internet access. Once these LDAP users login using pGINA, they are all redirected to the same AD account, a 'kiosk' account with GPOs in place to prevent anything malicious. My concern is that my users will accidentally save personal login information or files in that shared profile, and another user may login later and have access to a previous user's Gmail account, as the AppData folder on each computer is shared by anyone logging into the kiosk user. I've looked into MS's 'roll-your-own' SteadyState but it didn't seem to have what I wanted. I tried to write a PS script to copy a pre-saved clean version of the profile from a network share, but I just kept running into issues with CredSSP delegation and accessing the share from the UNC path. Others have recommended something like DeepFreeze but I'd like to do it without 3rd party tools if possible.

  Read the article

• How long will a "safely stored" Solid-State-Drive (SSD) keep its data? (e.g. bank safety-deposit box)

  - by user31575

  Here's my usecase: once-and-only-once copy off photos/videos to an internal SATA Solid State Drive (SSD) put this drive in a well-ventilated, air-conditioned bank "safety deposit box" for safe keeping The question: How long can I safely store a solid-state-drive in such an environment? i.e. 0% bitrot, 100% success when "plugged in" Are some SSD drives more reliable than other for this usecase? (e.g. smaller size vs larger size, SLC vs MLC, different brands, etc) More fodder: I have read that solid state memory cards (e..g compactflash, or sd cards) have much longer durability than other media (DVD's, CD's, hard drives) for this usecase (guaranteed against bitrot/other dysfunction on the order of ~ a decades vs a year ). I don't know if this applies to "SSD hard drives". Copying to one 500Gb ssd vs 8 64gb flash drives is easier SSD SATA hard drives have no moving parts, but they have more "visible electronics" than a compact flash card. I don't know if this "visible electronics" can fail, i.e. in contr I know many will point to carbonite, other cloud backup stuff, but I like the simplicity of having physical copies and wanted to understand the risks/implications thanks,

  Read the article

• Some of my keys are automatically being pressed along with other keys

  - by Santosh

  History The last time when my computer shutdown was a power failure. Now some keys are automatically being pressed when I type something. The last thing I did to keyboard setting was adding a keyboard layout (on Ubuntu). What is happening Whenever I press c, xc is writeen s gives me sd d gives me sd e gives me we 2 gives me 23, So when I want @ it gives me @# 3 gives me 23 Pressing CAPS Lock gives me F3 and vice-versa. All other key are either working fine or I don't use them. I have two operating system Ubuntu and Windows, I use Windows very less and found this problem on Ubuntu, but as soon as I logged in to Windows (for checking) then I found that Windows has the same problem. Effects on my life This starts form the time of login, even I have problem in typing my password. Whenever I try to save any webpage, it is bookmarked automatically. Whenever I copy, it is cut automatically. I have to spend more than half of time correcting what I have typed. Note: Typing thisd quwesdtion wasd rweally a big pain to mwe.

  Read the article

• P2V Wouldn't Boot, Rebuilt initrd, Need to Clean Up

  - by Mike Soule

  We have a CentOS 5.4 server (build 2.6.18-164.el5xen). We went to P2V this server so we can have redundancy, the physical only has one PSU. The P2V only completed 99% of the way, we have a VMWare ticket opened, but they marked the ticket as low priority. I was able to boot into a rescue disc of Red Hat 5.4 and rebuild the initrd with the help of this blog post. Now the only issue is the original server had a modified initrd, which was also from a different OS build and made by an outside provider. We do not have a document outlining modifications. My question is, is it at all possible to copy the initrd off of the physical server and replace it on the virtual and some how have the virtual machine boot? Thanks for any input. Edit: I copied the initrd img from the physical and it recreated the original issue. Here is a screen capture of the error. http://i.imgur.com/MqC73.jpg Edit2: echo Scanning logical volumes lvm vgscan --ignorelockingfailure echo Activating logical volumes lvm vgchange -ay --ignorelockingfailure VolGroup00 resume /dev/VolGroup00/LogVol01 echo Creating root device. mkrootdev -t ext3 -o defaults,ro /dev/VolGroup00/LogVol00 echo Mounting root filesystem. mount /sysroot

  Read the article

• Backup Picasa 'people' tags data

  - by pelms

  OK, so I've spent a fair amount of time putting names to faces in Picasa 3.5 but in a few days (hopefully) my copy of Windows 7 should arrive and I'll need to reinstall Windows. So, does anyone know what I need to backup so that I don't have to re-enter all those name tags? N.B. I'm on Windows 7 RC and know that I don't have to do a clean reinstall but I would prefer to. Outcome: I clean installed Windows 7 and downloaded and installed Picasa. Unfortunately, the download link on the UK Picasa homepage still pointed to Picasa 3.0 (rather than 3.5) which doesn't have face recognition. This scanned my photos folders and overwrote the picasa.ini files along with the people information   :¬( Fortunately I'd backed up the photos before installing Win 7, so after uninstalling Picasa 3.0 (along with it's database), restoring the photos from backup and installing Picasa 3.5, I finally got my face names back. Extra... Google has now posted advice on how to migrate to Windows 7 and keep your Picasa database, meaning that it will not need to rescan you photos and will retain all information about then including name tags. They have a method for upgrading and for a clean install of Win 7. Basically you need to back up: "C:\Users\%username%\AppData\Local\Google\Picasa2" and "C:\Users\%username%\AppData\Local\Google\Picasa2Albums"

  Read the article

• Moving a lot of small files between servers using rsync

  - by Adirael

  Hello guys, I'm moving a lot of files (about 2 millions) between two servers on different locations using rsync over ssh, it seems to work fine but I just realised I'm losing some files on the process. I got server 1, with the original data, and server 2, with the copy. Server 1 runs CentOS 5 and Server 2 runs on Ubuntu 10. I'm doing the transfer on the Server's 2 command line like this: rsync -e ssh -avzn usr@server1:/remote/path /local/path The first file movement I did using tar, but I didn't though of piping it through ssh and it failed cause the disk on server 1 was almost full, so I transfered it anyways (it was about 200GB) and got about 80% of the files. Then I piped another tar with the rest of the files (they're in folders, I got 100 folders with about 30 subfolders each, with files inside) and now I got everything on server 2. I wanted to be sure, so I my two options are getting the md5sum of all the files and check them or running an rsync on server 2 against server 1, that's what I did. It got some missing stuff and now it says there's nothing more to do (DRY RUN). But I got at least two files that are missing inside a subfolder. I ran that same rsync on that folder, but still dry run. Am I doing something wrong? Thanks, and sorry for the wall of text.

  Read the article

• Computer not finding hard drives on boot -sometimes-

  - by todd.pund

  Computer specs: Mobo: Gigabyte ultradurable 3 - GA-970A-UD3 Processor: First gen I7 3.2GHZ Ram: 8GB Kingston DDR3 1066 Video Card: EVGA NVidia GTX 460 1GB Hard Drive: 500MB 7200rpm x2 (can't remember brand, sorry I'm at work.) Last week my developer preview for Windows 8 ran out so I put my copy of windows 7 back on the computer. The computer at that point started suffering from frequent freezing and crashing. When I rebooted the computer sometimes it wouldn't find the system HD at all. When I looked at the post screen it seemed to show that it wasn't finding either of the HDs. Then yesterday when turning on the computer I just got GRUB as a message (not a GRUB prompt, just GRUB) I haven't had a dual boot of Linux for at least a year. I loaded windows 7 recovery console from the disk and ran: bootrec /fixboot bootrec /fixmbr Which did not help. At that point I just installed Ubuntu 13.04 over the windows 7 install and still received the GRUB post. I went into the BIOS and switched the Hard Drive priorities and then it loaded into Ubuntu fine. For several days everything was just hunky dory until I installed the Ubuntu version of Steam, install Portal and tried to run it. At that point the computer froze and after hard rebooting couldn't find the hard disks again. Then after restarting the system it loaded up fine again and no issues since. (I have not tried to launch portal again). My next thought is to remove the system hard drive and try to use the secondary as the master to see if the primary HD is bad. I'm sorry if this has been confusing, I'll answer any questions I can. Any thoughts?

  Read the article

• Server 2008 RAID 5 Write Speeds

  - by Solipsism

  I recently configured a RAID 5 partition in Server 2008 with 4 RAID 5 disks. These disks are connected through a SATA expansion card that uses PCIe. This morning, I checked and they had finally finished synchronizing, and so I tried to do some speed tests. Copying off the disks started pretty much fine - speeds began at 125MB/s, then trailed down to about 70MB/s, which I found odd but not worrying. Writing TO the disks however is a completely different story. I attempted to copy some of my VM host ISOs onto the disks (~2-4 GB apiece) and this resulted in speeds of approximately 10MB/s. I tried copying both from a local disk (connected directly to the motherboard) and from another server ththe gigabit network and results were the same. I checked the performance monitor while transferring the files and the only thing that stuck out was that my memory hard faults shot up to 6,000 per minute (spiking around 200/s) by explorer.exe. The system is running 2GB of DDR667 ECC RAM and a quad-core 2.3GHz opteron. Is there anything I can do to fix this performance issue (buy more RAM? move the drives to a faster box?, etc) or am I just screwed so long as I stick to windows.

  Read the article

• Common folder in linux

  - by rks171

  I have two users on my Ubuntu machine. I want to share some media files between these users, so I created a directory in /home/ called 'media'. I made the group 'media' and I added my user 'rks171' to the group 'media'. So: sudo groupadd media sudo mkdir -p /home/media sudo chown -R root.media /home/media sudo chmod g+s /home/media As was described in this post. Then, I added my user to the group: sudo usermod -a -G media rks171 Then I also added write permission to this folder for my group: sudo chmod -R g+w media So now, doing 'ls -lh' gives: drwxrwsr-x 2 root media 4.0K Oct 6 09:46 media I tried to copy pictures to this new directory from my user directory: mv /home/rks171/Pictures/* /home/media/ And I get 'permission denied'. I can't understand what's wrong. If I simply type, 'id', it doesn't show that my user, rks171, is part of the 'media' group. But if I type, 'id rks171', then it does show that my user, rks171, is part of the 'media' group. Anybody have any ideas why I can't get an files into this common folder?

  Read the article

• How do I cancel windows server 2003 repair install?

  - by Kilgore2k

  System: Windows 2003 Server Enterprise Scenario: NTDS db is corrupt and all attempts to fix with esentutl fail. Ran chkdsk which seemed to repair disk error and give access to the ntds.dit file but still esentutl fails. (Attached the drive to a different server to run the esentutl) Error: Access to source database '[path to copy of]/ntds.dit' failed with Jet error -1022. Operation terminated with error -1022 (JET_errDiskIO, Disk IO error) after 0.170 seconds. This error occurs on any disk I cpoy the files to including original location in C:\WINDOWS\NTDS\ Now enter the "Stupid!" and "what was I thinking!?" part (must be the late hour...) Stupid: No updated backup - after using a backup I get a network password error in the lsass error. what was I thinking!?: Started the install repair from the original CD but the install fails since the AD fails to start. Now I cant boot into any mode (safe mode, AD restore etc) nor complete the repair install. I would really like to avoid a fresh install since I have the Exchange server on this DC and would rather migrate to a new server than have to start from scratch. Thanks!

  Read the article

• Can a USB/IDE/SATA adapter be flaky?

  - by Ward

  I use USB/IDE/SATA converters a lot and on the two that I have now, I sometimes get errors copying files to drives. It only happens when I'm copying big files to the drive (big can mean as little as 100MB, I think it happens more often with bigger files - 300MB or more), and basically the copy will fail and I'll get one or more error messages about "Delayed write failed." But if I disconnect the drive and re-connect it, I'll usually be able to continue. (The file that was being copied will be corrupt, but otherwise the drive is fine.) I just noticed a new type of flakiness: the data transfer rate can vary widely. I copied one set of files (5x300MB files) and it took 10+minutes, then I copied another set (approx. the same sizes) and it took less than a minute. I haven't done systematic testing, the other things I'm doing on my laptop at the same time might have some impact, and I haven't cross-checked the two adapters I have and the 3 hard drives I'm working with to see if there's a pattern. I'm more wondering if anyone else has seen anything like this.

  Read the article

• Sync, share and backup policy using NAS

  - by Cue

  Trying to come up with a way to keep in sync while sharing and keeping a backup of my music/photos and movies. Currently I have an iMac in Greece and a MBP with me in the UK. As a result I've ended up with 2 iPhoto and iTunes libraries not to mention Documents scattered here and there, user settings etc. I also like to have a backup in case of a drive failure or the need to clean install. It seems that iPhoto and iTunes don't work really well with networked libraries. The way I think about it is to have a NAS where I keep my iTunes and iPhoto library but also rsync daily to my MBP to have a local copy. That way my files are shared across the network as well as act like a backup. In addition I get to have my files wherever I take my MBP but also have the ability to clean install. The tricky part comes from keeping in sync the iMac which is miles away. Again I'm considering a mirror setup (NAS, rsync to the iMac) as well as an rsync between the two NAS. It pretty much resembles the way Dropbox works, sans the requirement to go through their servers but I'm no "superuser" and don't really know if it is even feasible to have such a setup. Looks like there are so many things that can go wrong.

  Read the article

• 100% uptime for a web application

  - by Chris Lively

  We received an interesting "requirement" from a client today. They want 100% uptime with off-site failover on a web application. From our web application's viewpoint, this isn't an issue. It was designed to be able to scale out across multiple database servers, etc. However, from a networking issue I just can't seem to figure out how to make it work. In a nutshell, the application will live on servers within the client's network. It is accessed by both internal and external people. They want us to maintain an off-site copy of the system that in the event of a serious failure at their premises would immediately pick up and take over. Now we know there is absolutely no way to resolve it for internal people (carrier pigeon?), but they want the external users to not even notice. Quite frankly, I haven't the foggiest idea of how this might be possible. It seems that if they lose Internet connectivity then we would have to do a DNS change to forward traffic to the external machines... Which, of course, takes time. Ideas? UPDATE I had a discussion with the client today and they clarified on the issue. They stuck by the 100% number, saying the application should stay active even in the event of a flood. However, that requirement only kicks in if we host it for them. They said they would handle the uptime requirement if the application lives entirely on their servers. You can guess my response.

  Read the article

• How could I embed formatted XML source in WORD documents?

  - by eckes

  I'm writing a documentation with WORD that contains XML source code (whole files) as examples. The way I'm embedding the currently XML is quite cumbersome and doesn't seem to me as really maintainable: I'm finishing the editing of the document in WORD and create a PDF from it using Acrobat next, I open my XML files (2x input files, 2x generated output files) with IE and print them with the PDF printer supplied by Acrobat now, I open up Acrobat Pro and attach the four XML-PDF files to my original document The problem with that work flow for me is that it involves too much manual labor in order to get the documentation done. What I've tried up to now is not really satisfying for me: converting each XML to PDF and appending them like described above opening the XML files with SCiTE, copy as RTF and paste into Word playing around with the LaTeX packages minted, pygments and listings (I could write the docs with LaTeX too) but found some unsolvable problems in each of these packages I'm searching for a way that produces my documentation more automatic. For example embedding the XML files including formatting of IE (which I find quite readable). The files should be included by reference so that I don't have to paste the XML sources manually every time the XML changes.

  Read the article

• Shortcuts located in "D:\Program Data\..." not working even though they're pointing to the right targets (Windows 7)

  - by Kevin

  I just made a fresh install of my windows 7 home premium using my laptop's recovery disks (HP Pavilion dv6-2151cl) using minimal settings. After install, I set up "Program Data" and "Users" to my D partition to save space changing the folders in the registry. Then I updated windows (including W7 SP1), and installed all other programs. After installing all other programs I noticed that the icons of all new programs (not included in the windows install) in "All Programs" had a blank sheet as icon and they don't do anything. Looked into "D:\Program Data\Microsoft\Windows\Start Menu\Programs" in the windows explorer and the same is true there. All the shortcuts in C: and "D:\Users..." work both in the "Windows Explorer" and "All Programs". Also I noticed that the shortcuts do display the right icons inside the "open" dialog boxes. And if I copy the shortcuts in "D:\Program Data..." to the desktop they also work as expected. I checked file association for .lnk and it was OK, but also tried the registry fixers for this file association and they had no effect. There are no missing programs that I can tell in the "All Programs" menu, the just don't do anything if they lay in "D:\Program Data...". Any thoughts on how to make Windows 7 treat shortcuts in "D:\Program Data..." as they should?

  Read the article

• Microsoft Deployment Toolkit 2012 Error

  - by Jacob Schaer

  I just started with MDT2012 recently in hopes of eventually getting away with using Ghost to deploy all of our department computers. When I test deploy in VirtualBox, it deploys the OS properly, but stops because of a network driver failure (it gets the "could not allocate resources" issue). On physical hardware (Latitude E6500, Optiplex 980, and an older Latitude) it gets through the multicast and stops immediately after with: "Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information" I've looked at the logs and never see anything really of note. Originally I was using DriverPacks from DriverPacks.net, but thinking it was a driver issue, I switched over to using Dell's cab driver packs. Still the same issue. I check and it did the HDD is all fine - it was properly partitioned, set to bootable, and was loaded with all the proper OS installer files. I'm using a flash drive to do the install - when I make changes to the deployment share I rebuild and copy the ISO to the drive, then use YUMI multiboot to start the ISO (probably irrelevant).

  Read the article

• Windows 7 explorer crashing trying to read external hard disk

  - by Mario De Schaepmeester

  I have a 1TB Western Digital hard drive which is almost full and last time I tried to plug it into my laptop, I got a Windows dialog saying "this hard drive needs to be formatted". I did not panic because I have experienced things like this before and I know it's often solved by simply re-inserting the drive. Now however, whenever I plug it in and try to browse it in explorer by going to "computer", the explorer process crashes after a while. I simply close explorer since it takes ages trying to read the disk and nothing happens. After searching on the internet, the best thing to do would be a chkdsk. I tried it via properties in explorer (which also took a good 5 minutes to open up), locks up as well, after waiting a couple of minutes it says there's no access to the disk so a chkdsk is not possible... I want to make clear that I always use safe removal before pulling out the USB cable. Last time however, safe removal just would not work and when trying to shut down Windows, the logoff screen just would not disappear (I've waited at least 10 minutes or so) and I powered off the PC by force. This may be the cause of the problems but the disk was still recognised immediately after that. I really don't want to format this thing because it contains C: clones of 3 computers and a lot of other stuff that I don't want to re-copy. What would be the best course of action? Update I got chkdsk working via the command line. I used the /F and /R options. I already got a bunch of lines saying "file record segment X is unreadable" or whatever it is in English, my OS is Dutch. It looks bad... Will chdsk repair these errors?

  Read the article

• Script to mirror MS SQL Server databases between 2 servers

  - by David W

  Hi I have about 200 sites each of which have 2 servers running MSSQL (2k5 at some sites, 2k8 at others) One server is production and the other is primarily there as a backup. We're rebuilding all of these servers this year and as part of that we will have to set up mirroring for ... a lot ... of databases. Some of these sites have 45 databases so mirroring them manually is going to be a huge pain. I was going to write a batch script which uses SQLCMD to backup the database and log, copies to the secondary server, restores the backup and log with norecovery, creates the endpoints and sets the partner. This in itself isn't too complicated, but i'd love to see what other people have done as i'm not very confident in catching errors using the process i've outlined above. I've seen Tools to manage sql 2008 database mirroring? Which looks really good, but the formatting is jumbled and I can't get it to work. If anyone has any other scripts they've written and are willing to share I'd be eternally grateful. Ideally I'd love to be able to use a script to ensure there are matching endpoints (same ports) on both servers, backup the database, backup the log, copy the backups to second server, restore database and log with norecovery, set the partners on both servers, and somehow confirm that the databases are linked and synchronized. Well, thanks for reading :)

  Read the article

• Troubles Installing Windows 7 via USB. Flat install?

  - by Brian

  Hi friends, I've been struggling with this for a while. Windows 7 64-bit Enterprise edition just will not install on my Shuttle K45 system via a USB key. It hangs out during the install while copying files or while creating the partitions. The system is pretty standard and low-tech: IDE hard drives, no CD, 2G RAM. I am not sure what of the problem. Other than the Shuttle, I have a Apple MacBook Pro. On the MPB, I am running OS X, and Mint Linux and Window XP over Parallels. I have an ISO of Win7 that works (I installed it as a Parallels VM to make sure). I have used UltraISO and MS Windows 7 USB/DVD Download Tool to write it to the 8G USB key. Both seem to copy all the files correctly (with UltraISO, I asked it to verify). It boots via USB and the install looks just fine. Until it hangs, most of the time with a copying error of 0x80070241. So now I am trying to figure out if there are other ways I can install Windows 7 on this Shuttle system that has no CD drive. I've heard about a flat installation, however those all seem to be doing something from within Windows. I do have access to a command prompt from the Windows 7 install. Does anyone know if/how I can prep the Shuttle hard drive with Windows 7 installation and have Windows 7 install from the hard disk. I do not have an external enclosure for the IDE HD and I do not have any other system I can hook up to the hard drives. I do have an external Maxtor OneTouch drive available.

  Read the article

< Previous Page | 475 476 477 478 479 480 481 482 483 484 485 486  | Next Page >