Search Results

Search found 62754 results on 2511 pages for 'program stopped working'.

Page 48/2511 | < Previous Page | 44 45 46 47 48 49 50 51 52 53 54 55  | Next Page >

• HDMI Sound Stops Working

  - by stueng

  When not used for a few hours the sound stops working on my HTPC. To get sound to work again I have to unplug the HDMI cable and plug it back in again When this sound "outage" occurs, the HDMI device dissapears from the sound config output devices I see the following in dmesg [78534.010328] HDMI hot plug event: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [78534.010363] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [78558.948403] HDMI hot plug event: Codec=0 Pin=3 Presence_Detect=1 ELD_Valid=1 [78558.948429] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [78562.579047] HDMI hot plug event: Codec=0 Pin=3 Presence_Detect=1 ELD_Valid=0 [78562.579078] HDMI status: Codec=0 Pin=3 Presence_Detect=1 ELD_Valid=1 [78562.579992] HDMI hot plug event: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=1 [78562.580043] HDMI status: Codec=0 Pin=3 Presence_Detect=1 ELD_Valid=1 [78562.876030] HDMI status: Codec=0 Pin=3 Presence_Detect=1 ELD_Valid=1 [78563.176036] HDMI status: Codec=0 Pin=3 Presence_Detect=1 ELD_Valid=1 [78563.195139] HDMI hot plug event: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [78563.195169] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [78563.476030] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [78635.529493] HDMI hot plug event: Codec=0 Pin=3 Presence_Detect=1 ELD_Valid=1 [78635.529524] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [78641.330701] HDMI hot plug event: Codec=0 Pin=3 Presence_Detect=1 ELD_Valid=0 [78641.330733] HDMI status: Codec=0 Pin=3 Presence_Detect=1 ELD_Valid=1 [78641.331649] HDMI hot plug event: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=1 [78641.331668] HDMI status: Codec=0 Pin=3 Presence_Detect=1 ELD_Valid=1 [78641.628050] HDMI status: Codec=0 Pin=3 Presence_Detect=1 ELD_Valid=1 [78641.928037] HDMI status: Codec=0 Pin=3 Presence_Detect=1 ELD_Valid=1 [78642.228042] HDMI status: Codec=0 Pin=3 Presence_Detect=1 ELD_Valid=1 [78642.528039] HDMI status: Codec=0 Pin=3 Presence_Detect=1 ELD_Valid=1 [78642.828037] HDMI status: Codec=0 Pin=3 Presence_Detect=1 ELD_Valid=1

  Read the article

• Gett Tor and Irssi working together

  - by Joey Bagodonuts

  Hi I am trying to get Tor working with Irssi. The directions at the bottom of this page Freenode Install Link say to :~/.irssi$ tor MapAddress 10.40.40.40 p4fsi4ockecnea7l.onion Feb 12 04:26:51.101 [notice] Tor v0.2.1.29 (r318f470bc5f2ad43). This is experimental software. Do not rely on it for strong anonymity. (Running on Linux x86_64) Feb 12 04:26:51.101 [warn] Command-line option 'p4fsi4ockecnea7l.onion' with no value. Failing. Feb 12 04:26:51.101 [err] Reading config failed--see warnings above. Or add it to the torrc file and reload irssi .irssi$ cat /etc/tor/torrc |grep 10.40.40 mapaddress 10.40.40.40 p4fsi4ockecnea7l.onion This is a paste from within irssi after running $torify irssi [04:33] Math::BigInt: couldn't load specified math lib(s), fallback to Math::BigInt::FastCalc at /usr/local/share/perl/5.10.1/Crypt/DH.pm line 6 [04:33] [04:33] *** Irssi: Loaded script cap_sasl So I thought it was a CPAN module issue. cpan[1]> install Math::BigInt This was also done for FastCalc and retried with force install. What am I doing wrong? Thanks

  Read the article

• My experience working with Teradata SQL Assistant

  - by Kevin Shyr

  Originally posted on: http://geekswithblogs.net/LifeLongTechie/archive/2014/05/28/my-experience-working-with-teradata-sql-assistant.aspx To this date, I still haven't figure out how to "toggle" between my query windows. It seems like unless I click on that "new" button on top, whatever SQL I generate from right-click just overrides the current SQL in the window. I'm probably missing a "generate new sql in new window" setting The default Teradata SQL Assistant doesn't execute just the SQL query I highlighted. There is a setting I have to change first. I'm not really happy that the SQL assistant and SQL admin are different app. Still trying to get used to the fact that I can't quickly look up a table's keys/relationships while writing query. I have to switch between windows. LOVE the execution plan / explanation. I think that part is better done than MS SQL in some ways. The error messages can be better. I feel that Teradata .NET provider sends smaller query command over than others. I don't have any hard data to support my claim. One of my query in SSRS was passing multi-valued parameters to another query, and got error "Teradata 3577 row size or sort key size overflow". The search on this error says the solution is to cast result column into smaller data type, but I found that the problem was that the parameter passed into the where clause could not be too large. I wish Teradata SQL Assistant would remember the window size I just adjusted to. Every time I execute the query, the result set, query, and exec log auto re-adjust back to the default size. In SSMS, if I adjust the result set area to be smaller, it would stay like that if I execute query in the same window.

  Read the article

• VHOST not working in Apache

  - by Starx

  I got a LAMP server working in Ubuntu 11.04. Now the problem is that the websites have to enabled and disabled from the terminal. All all of them have to be accessed from http://localhost which is not so much efficient. So I created a VHOSTS, using some tutorials off the net. Here is the coding for it <VirtualHost *:80> ServerAdmin webmaster@localhost Servername site.com ServerAlias www.site.com DocumentRoot /home/starx/public_html/site/public <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /home/starx/public_html/site/public> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> nGen ErrorLog ${APACHE_LOG_DIR}/site-error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/site-access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> Now, still I can't access the page in http://site.com but if i access using http://localhsot/ it is accessed. I have disabled all others site including default and have just enabled one site i.e. site How to fix this?

  Read the article

• How to get Broadcom BCM 43XX Wireless card working

  - by Fer1805

  NOTE - Although this question is for a specific version of Ubuntu and a specific Broadcom model, the answer to it is for most Broadcom models and versions of Ubuntu 11.04, 11.10, 12.04 and 12.10. If you have come here from another question, feel free to read the answer instead. The answer covers many problems with several solutions. I'm having serious problems installing the Broadcom drivers for Ubuntu 11.04. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in Linux, so I would need clear explanations on make, compile, etc. I was following the instructions on the following blog, with no luck. How can I get Broadcom BCM4311 Wireless working? Can someone help me? Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. hope above info is enough for your help.

  Read the article

• Focus follows mouse stops working when opening window from launcher and no click to focus

  - by user97600

  This is 12.04 default desktop (unity). I set it to focus follows mouse, and changed the menus to be on the window. This worked for a while, then some unknown even, maybe an upgrade maybe some other setting change caused it to stop working. There are many ways for this behavior to start but one reliable one is to bring a window to the foreground/focus with the launcher. Now the focus is stuck on that window and not just the window but the regions within the window so the close, maximize, minimize and menus do not work. I have to use mouse middle and then mouse right and then focus follows mouse is restored for a bit. The exact details of the mouse action aren't clear, sometimes it seems like just mouse middle helps, sometimes just right some times a desperate sequence of clicks :-( I have tried switching to the gnome desktop and it seems to occur less there but it is not eliminated. I have tried switching mice to an old wired USB mouse. I have tried creating a new account and that has not worked. I have observed "split focus" where to scroll button scrolls one one window but the input goes to another. I go trapped recently where my keyboard input went to libre office calc, but I was selecting the search term in the chrome address window. The selection "grayed" but the keyboard input for the search went to libre. Regions in windows have very confused focus. I have to work hard to get focus on for example the close gliph (X) or the minimize gliph (_).

  Read the article

• Ubuntu 12.04 - Brightness controls not working

  - by Juan Manuel Zolezzi Volpi

  Controls from "Brightness and Lock" were not working so I've tried a solution that involved changing grub, which I'm detailing below: # If you change this file, run 'update-grub' afterwards to update # /boot/grub/grub.cfg. # For full documentation of the options in this file, see: # info -f grub -n 'Simple configuration' GRUB_DEFAULT=0 #GRUB_HIDDEN_TIMEOUT=0 GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=10 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX="quiet splash acpi_backlight=vendor" # Uncomment to enable BadRAM filtering, modify to suit your needs # This works with Linux (no patch required) and with any kernel that obtains # the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...) #GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xefefefef" # Uncomment to disable graphical terminal (grub-pc only) #GRUB_TERMINAL=console # The resolution used on graphical terminal # note that you can use only modes which your graphic card supports via VBE # you can see them in real GRUB with the command `vbeinfo' #GRUB_GFXMODE=640x480 # Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux #GRUB_DISABLE_LINUX_UUID=true # Uncomment to disable generation of recovery mode menu entries #GRUB_DISABLE_RECOVERY="true" # Uncomment to get a beep at grub start #GRUB_INIT_TUNE="480 440 1" After doing this, the brightness control dissapeared like you can see at http://screencloud.net/img/screenshots/6b90d56604b70cc749a632d0bc005a20.png Any ideas? Would love to be able to configure Brightness or even use apps like F.lux to regulate it automatically. Edit: I've modified the following line to GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi_osi=" and now the brightness controls are back, but whatever I change the brightness remains the same. Just in case I'm using Intel H77

  Read the article

• Logitech USB headset not working on 12.04

  - by thepeoplescoder

  I've looked around for answers to this question, But none of them seem to work for my particular problem. Obviously my USB headset isn't working, But I might as well share the scenario. I am running Ubuntu 12.04 and I have a Logitech USB headset. The relevant output from dmesg is as follows: [160708.528047] usb 2-1.2: USB disconnect, device number 9 [160768.890123] usb 2-1.2: new full-speed USB device number 10 using ehci_hcd [160768.997578] input: Logitech Logitech USB Headset as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.3/input/input15 [160768.997795] generic-usb 0003:046D:0A0C.0005: input,hidraw0: USB HID v1.00 Device [Logitech Logitech USB Headset] on usb-0000:00:1d.0-1.2/input3 When I go to System Settings - Sound, My headset shows up in both the Output and Input tabs, It is called "Clear Chat Comfort USB Headset" in those tabs, But I doubt that's a serious issue. When I click my headset in either tab to use it, The changes are not remembered when I reopen the sound settings, the built-in audio is still used. Also when I select the headset in the Output tab, and click the Test Sound button to test everything, The sound still comes from my laptop's onboard audio, instead of from my USB headset. Does anyone know how to correct this? I am stumped.

  Read the article

• Staying OO and Testable while working with a database

  - by Adam Backstrom

  What are some OOP strategies for working with a database but keeping thing testable? Say I have a User class and my production environment works against MySQL. I see a couple possible approaches, shown here using PHP: Pass in a $data_source with interfaces for load() and save(), to abstract the backend source of data. When testing, pass a different data store. $user = new User( $mysql_data_source ); $user-load( 'bob' ); $user-setNickname( 'Robby' ); $user-save(); Use a factory that accesses the database and passes the result row to User's constructor. When testing, manually generate the $row parameter, or mock the object in UserFactory::$data_source. (How might I save changes to the record?) class UserFactory { static $data_source; public static function fetch( $username ) { $row = self::$data_source->get( [params] ); $user = new User( $row ); return $user; } } I have Design Patterns and Clean Code here next to me, but I'm struggling to find applicable concepts.

  Read the article

• Emulator PCSX Reloaded - Fullscreen not working on Unity

  - by Leonardo Montenegro

  I have an older PS1 console with a couple of games I bought some years ago. On my pc, I'm using PCSX Reloaded - the best PS1 emulators for Linux I found so far. But I'm having a little issue on Ubuntu 12.04 Precise. I'm using Unity 3D and I'm trying to run some of my original PS1 games on PCSX Reloaded. Everything works nicely, except for fullscreen. I toggle fullscreen and specify maximum resolution for my monitor, but on fullscreen mode, both left and top unity bars aren't getting hidden. I tried changing between other graphic modes like Gnome Classic and Gnome Classic w/o Effects. On both, PCSX shows bars in fullscreen mode, so it isn't an Unity-specific issue, but an emulator problem. It's a bit annoying play games this way, so basically I'm running games on window mode for now. I'm using default OpenGL graphic plugin on this emulator. I tried changing to X11 graphic plugin and fullscreen worked, but graphics on X11 plugin aren't as good as OpenGL one. Anyone know a way to get fullscreen working on PCSX using OpenGL plugin? Or maybe another graphic plugin w/ OpenGL support.

  Read the article

• How do I get a Broadcom BCM4311 working?

  - by Fer1805

  I'm having serious problems installing the broadcom drivers for ubuntu 11.04. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in linux, so I would need clear explanations on make, compile, etc. I was following the instructions on the following blog, with no luck. Broadcom BCM4311 Wireless not working Can someone help me? Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. hope above info is enough for your help.

  Read the article

• Upgrade to Ubuntu 13.10 in a VirtualBox: Gnome desktop not working

  - by Xavier

  I had Ubuntu 13.04 running in a VirtualBox (the host is WinXP). I've upgraded it to 13.10 but I've some issues: Gnome desktop is not working correctly (I can log in but the main menu bar remains empty - I can only log out with CTRL-ALT-BACKSPACE) I cannot build and install the VirtualBox Guest Addons: When trying to build it, it says: me@virtuntu:/etc/init.d$ sudo ./vboxadd setup Removing existing VirtualBox DKMS kernel modules ...done. Removing existing VirtualBox non-DKMS kernel modules ...done. Building the VirtualBox Guest Additions kernel modules The headers for the current running kernel were not found. If the following module compilation fails then this could be the reason. Building the main Guest Additions module ...done. Building the shared folder support module ...fail! (Look at /var/log/vboxadd-install.log to find out what went wrong) Doing non-kernel setup of the Guest Additions ...done. In the log file, I see the following error: /tmp/vbox.0/dirops.c:292:5: error: unknown field ‘readdir’ specified in initializer .readdir = sf_dir_read, ^ /tmp/vbox.0/dirops.c:292:5: warning: initialization from incompatible pointer type [enabled by default] /tmp/vbox.0/dirops.c:292:5: warning: (near initialization for ‘sf_dir_fops.flush’) [enabled by default] make[2]: *** [/tmp/vbox.0/dirops.o] Erreur 1 make[1]: *** [_module_/tmp/vbox.0] Erreur 2 make: *** [vboxsf] Erreur 2 Creating user for the Guest Additions. Anyone had a similar experience? Any clue to help me? Thanks a lot!

  Read the article

• lirc_zilog IR transmission no longer working with HD-PVR on 12.04

  - by johnf

  I have been running a ubuntu 10.04 with a patched version of lirc_zilog for two years. I upgraded to 12.04 and lirc_zilog is no longer working with my HD-PVR. The MythTV wiki reports that it did work out of the box with 11.04. The error message I get on irsend is as follows: johnf@carbon:~$ /usr/local/bin/irsend SEND_ONCE blaster 0_130_KEY_POWER irsend: command failed: SEND_ONCE blaster 0_130_KEY_POWER irsend: hardware does not support sending The lircd daemon, run interactively, reports the following: lircd: accepted new client on /var/run/lirc/lircd lircd: could not get hardware features lircd: this device driver does not support the LIRC ioctl interface lircd: major number of /dev/lirc0 is 250 lircd: LIRC major number is 61 lircd: check if /dev/lirc0 is a LIRC device lircd: WARNING: Failed to initialize hardware lircd: error processing command: SEND_ONCE blaster 0_130_KEY_POWER lircd: hardware does not support sending lircd: removed client Checking dmesg seems to indicate that the kernel module is loading properly: [56497.730743] lirc_zilog: module is from the staging directory, the quality is unknown, you have been warned. [56497.730999] lirc_zilog: Zilog/Hauppauge IR driver initializing [56497.732484] lirc_zilog: ir_probe: ir_rx_z8f0811_hdpvr on i2c-0 (Hauppage HD PVR I2C), client addr=0x71 [56497.732493] lirc_zilog: ir_probe: ir_tx_z8f0811_hdpvr on i2c-0 (Hauppage HD PVR I2C), client addr=0x70 [56497.732496] lirc_zilog: probing IR Tx on Hauppage HD PVR I2C (i2c-0) [56497.756822] lirc_zilog: firmware of size 302355 loaded [56497.756945] lirc_zilog: 743 IR blaster codesets loaded [56497.757030] i2c i2c-0: lirc_dev: driver lirc_zilog registered at minor = 0 [56497.757033] lirc_zilog: IR unit on Hauppage HD PVR I2C (i2c-0) registered as lirc0 and ready [56497.757035] lirc_zilog: probe of IR Tx on Hauppage HD PVR I2C (i2c-0) done [56497.757056] lirc_zilog: initialization complete Here is my /etc/lirc/hardware.conf #Chosen IR Transmitter TRANSMITTER="HD-PVR" TRANSMITTER_MODULES="lirc_dev lirc_zilog" TRANSMITTER_DRIVER="" TRANSMITTER_DEVICE="/dev/lirc0" TRANSMITTER_SOCKET="" TRANSMITTER_LIRCD_CONF="" TRANSMITTER_LIRCD_ARGS="" My lircd.conf is a copy of the recommended one. Examination of the kernel source seems to indicate that the lirc_zilog module should support transmission, it's newer than the patched version I was manually compiling on 10.04. I was previously using a manually built version of lirc 0.8.7 and not the packaged one. I'm now running the packaged version 9.0. I can provide any additional information required and will perform tests quickly. I'm very eager to get this issue resolved.

  Read the article

• Wifi not working on Acer Aspire One D270

  - by Dani

  brand new baby linux user here, never used Ubuntu or any other linux OS before, so be gentle and use short words! I installed Ubuntu 12.04 on my new Acer Aspire One D270-F61C/KF netbook (it's a Japanese computer which had Japanese windows preinstalled, and I decided to take the plunge and try Ubuntu because English Windows costs the earth and stars). Wifi isn't working; I enter my wireless password, it tries to connect for a while, then asks for my password again. And KEEPS ASKING, every few minutes. Wired connection works fine. Wireless card is a Broadcom BCM4313; I have the "additional drivers" checked and installed (I tried unchecking and then reinstalling them in case that would help, no joy, and now my home wifi connection isn't showing up in the list of available connections, argh). I've done a lot of googling and I gather there's a lot of issues with Broadcom cards, but some of the answers are for earlier ubuntu builds and many of them are a bit confusing for a new user. I gather I need to try installing some new drivers other than the proprietary ones provided, but I'm having trouble figuring out how that's done. Anyone got some simple, step by step instructions for me? Please bear in mind, TOTAL N00B. (EDIT): OKAY, got it fixed finally; after suggestions on the Ubuntu forums and messing around with drivers, what finally worked was installing Wicd. Not... using Wicd, for some reason, just installing it fixed it. ...I CHOOSE NOT TO QUESTION IT.

  Read the article

• How to pick a great working team?

  - by Javierfdr

  I've just finished my master and I'm starting to dig into the laboral world, i.e. learning how programming teams and technology companies work in the real world. I'm starting to design the idea of my own service or product based on free software, and I will require a well coupled, enthusiast and fluid team to build and the idea. My problem is that I'm not sure which would be the best skills to ask for a programming team of 4-5 members. I have many friends and acquaintances, with whom I've worked during my studies. Must of those ones I have in mind are very capable and smart people, with a good logic and programming base, although some of them have some characteristics that I believe that could influtiate negatively in the group: lack of communication, fear to debate ideas, hard to give when debating, lack of structured programming (testing, good commenting, previous design and analysis). Some of them have this negative characteristics, but must of them have a lot of enthusiasm, nice working skills (from an individual point of view), and ability to see the whole picture. The question is: how to pick the best team for a large scale project, with a lot of programming? Which of these negative skills do you think are just too influential? Which can be softened with good leadership? Wich good skills are to be expected? And any other opinion about social and programming skills of a programming team.

  Read the article

• Working with Reporting Services Filters – Part 2: The LIKE Operator

  - by smisner

  In the first post of this series, I introduced the use of filters within the report rather than in the query. I included a list of filter operators, and then focused on the use of the IN operator. As I mentioned in the previous post, the use of some of these operators is not obvious, so I'm going to spend some time explaining them as well as describing ways that you can use report filters in Reporting Services in this series of blog posts. Now let's look at the LIKE operator. If you write T-SQL queries, you've undoubtedly used the LIKE operator to produce a query using the % symbol as a wildcard for multiple characters like this: select * from DimProduct where EnglishProductName like '%Silver%' And you know that you can use the _ symbol as a wildcard for a single character like this: select * from DimProduct where EnglishProductName like '_L Mountain Frame - Black, 4_'   So when you encounter the LIKE operator in a Reporting Services filter, you probably expect it to work the same way. But it doesn't. You use the * symbol as a wildcard for multiple characters as shown here: Expression Data Type Operator Value [EnglishProductName] Text Like *Silver* Note that you don’t have to include quotes around the string that you use for comparison. Books Online has an example of using the % symbol as a wildcard for a single character, but I have not been able to successfully use this wildcard. If anyone has a working example, I’d love to see it!

  Read the article

• Nvidia 740M still not working after Bumblebee installation

  - by Jon

  first of all, I have checked a lot of similar topics, but I still can't get my laptop to use Nvidia 740M. So first things first. I have a laptop Asus X550V(i5-3230, 4gb RAM, Nvidia 740M + Intel HD4000). I installed Ubuntu 13.10 alongside Win8(preinstalled) and both systems are running without problems. However, I have problem with second graphic card(Nvidia 740M), as Ubuntu doesn't recognize it. I installed bumblebee with this tutorial https://wiki.ubuntu.com/Bumblebee#Installation, but I still get error "Cannot access secondary GPU" error when trying to run ''optirun Steam'' in terminal. Then I tried to do this: [ERROR]Cannot access secondary GPU - error: [XORG] (EE) No devices detected. you need to edit the /etc/bumblebee/xorg.conf.nvidia (or /etc/bumblebee/xorg.conf.nouveau if using the noveau driver) and specify the correct BusID by following the instructions therein. But with lspci / VGA i get only info about Intel 4000, but no Nvidia. When I type only lspci, I get the line for Nvidia 740M,but after I edit the config file I still get second card error. Also, in /etc/bumblebee/xorg.conf.nvidia there wasn't BusID or anything similar, so I just added the whole line in device section. As I sad, I tried a lot of things to get it working, avoiding this forum(as I din't want to bother people with some solutions possible), but alas!, I had to bother you. If there is a need for some additional info, just say, no problem at all. Thank you very much in advance. :)

  Read the article

• Internal Mic not working on Dell Adamo 13

  - by AFD

  So I'm using Elementary Luna Beta (based on Ubuntu 12.04 LTS) on a spare HDD after successfully using Jupiter release (based on 10.10) for many years. In Jupiter I had my internal mic work out of the box and with Skype installed from deb it was all setup without having to step foot inside the terminal. In Luna Beta the internal mic is not recognised by the OS and so also not recognised by Skype. I believe the hardware is this (from sudo lshw): *-multimedia description: Audio device product: 82801I (ICH9 Family) HD Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 03 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=HDA Intel latency=0 resources: irq:46 memory:f8600000-f8603fff As well as this I ran cat /proc/asound/card0/codec* | grep Codec which gave me: Codec: IDT 92HD73C1X5 Codec: Intel Cantiga HDMI How do I tweak Luna to get this hardware working properly? I'm able to switch out my Luna HDD with the Jupiter HDD to help troubleshoot what the differences are between the two and why the more recent OS can't find / use the mic correctly. Thanks in advance for any help you can give.

  Read the article

• Yoga Pro 2 Wi-Fi not working

  - by user293004

  I installed Ubuntu 14.04 on my new Yoga Pro 2 and the wireless is not working. It started with Windows 8 on it. The Network Manager says Wi-Fi is disabled by hardware switch. I tried putting a blacklist file in ect/modprobe.d as has been suggested in many places. I called the file "blacklist-ideapad_laptop.conf" and wrote in the file blacklist ideapad_laptop I checked to make sure that the wireless is enabled in the BIOS. It is. I ran rfkill list all and it displayed: 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes I ran iwlist wlan0 scan and it displayed: wlan0 Failed to read scan data : Network is down I ran sudo rmmod ideapad_laptop and it displayed: rmmod: ERROR: Module ideapad_laptop is not currently loaded. I ran ifconfig wlp1s0 up and it displayed: wlp1s0: ERROR while getting interface flags: No such device. I ran "lspci" and it displayed: 01:00.0 Network controller: Intel Corporation Wireless 7260 (rev 6b) I ran sudo lshw -c network and it displayed: *-network DISABLED description: Wireless interface product: Wireless 7260 vendor: Intel Corporation physical id: 0<br> bus info: pci@0000:01:00:0.0 logical name: wlan0 version: 6b serial: 7c:7a:91:5f:9b:fa width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-24-generic firmware=22.24.8.0 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:61 memory:b0400000-b0401fff This No wireless with Intel Centrino Advanced-N 7260 seems to be dealing with a similar issue. It suggests that I need to update my firmware. So I downloaded iwlwifi-7260-ucode-23.214.9.0 from Intel's website. I put the file "iwlwifi-7260-9.ucode" in /lib/firmware and ran "sudo lshw -c network" again. It displayed exactly as before. Is there something else I need to do install the new firmware?

  Read the article

• Dell Alps Touchpad not working

  - by ppls

  I have a Dell 17R SE with Ubuntu 13.04. The touchpad is recognized as PS/2 mouse out of the box, giving just normal touchpad behaviour, but no tap to click, no scrolling, etc. Most answers related to that issue suggest trying an ALPS driver from dahetral.com: http://www.dahetral.com/public-download For installing I followed the steps on this page: https://www.linuxwind.org/html/dell-touchpad-driver-for-ubuntu-13-04.html Now my xinput looks like this: Virtual core pointer id=2 [master pointer (3)] ? ? Virtual core XTEST pointer id=4 [slave pointer (2)] ? ? PS/2 Mouse id=13 [slave pointer (2)] ? ? AlpsPS/2 ALPS GlidePoint id=14 [slave pointer (2)] ? ? Logitech Bluetooth Mouse M555b id=16 [slave pointer (2)] My touchpad isn't working at all now, just the two hardware buttons for left and right mouse buttons work. Interestingly also the tap to click functions works, but only in the address bar of nautilus, nowhere (!) else. What can I do? I would even switch back to initial state, where at least the basic touchpad functionality worked, i I knew, how to get there.

  Read the article

• Trendnet tew-424ub wireless not working after update 12.10

  - by dwa

  I updated packages from the software manager and now my wireless won't work. It's a Trendnet tew-424ub iwconfig says lo no wireless extensions. eth0 no wireless extensions. sudo lshw -C network: description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 1c:6f:65:46:e9:d4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.137 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:de00(size=256) memory:fdaff000-fdafffff memory:fdae0000-fdaeffff memory:fda00000-fda0ffff lsusb: Bus 003 Device 002: ID 0bc2:3332 Seagate RSS LLC Expansion Bus 003 Device 003: ID 05e3:0605 Genesys Logic, Inc. USB 2.0 Hub [ednet] Bus 003 Device 006: ID 0457:0163 Silicon Integrated Systems Corp. 802.11 Wireless LAN Adapter Bus 005 Device 002: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 005: ID 0781:5530 SanDisk Corp. Cruzer Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Help? I'm not sure where to start. I've been browsing forums and such for a long time and nothing I try is working.

  Read the article

• Select (loop) or command not working in shell-script

  - by user208098

  I've been tinkering with Linux and Unix for years but still a novice in my mind and recently find myself trying to be more pro with it as I work in IT. So with that notion I'm studying shell scripting. I've hit a snag in ubuntu using the latest version 13.10 Saucy. When I use the select command in a sh script it doesn't work, depending on how I format the command it will either return Unexpected "do" or Unexpected "done". See the following two examples: This section of code produces an unexpected "do" error: #/bin/bash PS3='Please enter your choice' select opt in option1 option2 option3 quit do case $opt in "option1") echo "you chose choice 1" ;; "option2") echo "you chose choice 2" ;; "option3") echo "you chose choice 3" ;; "quit") break ;; *) echo invalid option ;; esac done This section of code produces an unexpected "done" error. #/bin/bash PS3='Please enter your choice' select opt in option1 option2 option3 quit ; do case $opt in "Option1") echo "you chose choice 1" ;; "Option2") echo "you chose choice 2" ;; "Option3") echo "you chose choice 3" ;; "quit") break ;; *) echo invalid option ;; esac done When I enter these parameters into the command line interactively or manually I get the desired result which is a list of choices to choose from. However when executed from a script I get the before mentioned errors. Also a side note I have tried this in Fedora as a script and it worked perfectly so my question is why isn't it working in Ubuntu, is this a difference between RHL and Debian? Or is it a bug in the latest version of Ubuntu? Thanks in advance for any help! KG

  Read the article

• GRUB2 not working after installing xubuntu 14.04

  - by h3bm

  I have a vaio laptop and it used to have installed windows 8 and Xubuntu 13.04 in dual boot, everything was working fine. I decided to update my version of xubuntu 14.04 LTS mainly because the support for 13.04 is finished and LTS version have 3 years of support. What I did was to format the partition where xubuntu 13.04 was installed and install 14.04 in that formated partition. When I restarted my computer willing to start using my new system I got the following message: error: symbol 'grub_term_highlight_color' not found and I was not able to enter any OS. I tried boot-repair from live USB more than two times and it did not fix the problem. I tried to enter to my computer using super GRUB2 disk, however it does not apperar to work with UEFI active (besides super grub2 disk says it can) I only get the message "no operating system found". If I boot super grub2 disk with UEFI disabled, super grub2 disk can not detect any OS,I also tried Rescatux distro, however, as of super grub2 disk, rescatux cannot enter when UEFI is active. I tried boot-repair with the option of "restore EFI backups", after that I was able to boot on windows, but no grub menu appeared. I ran boot-repair again with no improving results Here is the last Bootinfo report I got: http://paste.ubuntu.com/7609801/ Do you have any idea of what is happening? I really appreciate your help, Best regards,

  Read the article

• Sound not working after installing PCI video card and then removing it

  - by bakhshu

  I am running 11.10 on a HP/Compaq Presario sr1010z, and the video/audio was working fine with whatever was in the machine already. Then I installed a new video card (PCI/nVidia), which disabled the audio/video on the old one automatically. But that card didn't work out too well so I removed it. Now the video is back to normal, but the audio is gone. I have tried the following: 1. In BIOS, set audio to on/enable rather than Auto 2. Looked for hardware in System Settings Sound, but nothing shows up there 3. But when I run the sysinfo utility, I get the description of the audio controller When I do a 'sudo aplay -l', I get 'aplay: device_list:240: no soundcards found...' And then when I do a 'lspci -v | grep -A7 -i "audio"' I get the following: 00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS7012 AC'97 Sound Controller (rev a0) Subsystem: Hewlett-Packard Company Device 2a05 Flags: bus master, medium devsel, latency 32, IRQ 5 I/O ports at a000 [size=256] I/O ports at a400 [size=128] Capabilities: 00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) (prog-if 10 [OHCI]) Any ideas on how to fix this? Thanks

  Read the article

• Electricsheep Not Working in Raring 13.04

  - by Nhoeh37

  I just downloaded Electricsheep four days before I updated my Ubuntu software and I fell in love with it. After I upgraded to 13.04, I'm kind of upset in saying that Electricsheep no longer works. I have no idea how to fix it and I feel helpless with Linux. As I said, it was working completely fine in 12.10, but now with the Raring Ringtail update: I use Xscreensaver to launch Electricsheep. When I open Xscreensaver, "Electricsheep" is one of the options to choose. When I "preview" ES or even launch the "xscreensaver-demo" in the terminal, it doesn't work anymore; I get an error message. The error message says: "detected another electric sheep process. rendering of sheep is disabled using read only access." Damnit, can someone please help me? I want my trippy screensaver back, it shouldn't be this hard! EDIT: I contacted the creator of Electricsheep (Scott Draves) via the link to his email address on his personal website and asked for his assistance. Hopefully the Askubuntu community will be able to fix this problem, I'm sure I am not the only one who is having this problem as I have searched and searched.

  Read the article

< Previous Page | 44 45 46 47 48 49 50 51 52 53 54 55  | Next Page >