Search Results

Search found 20799 results on 832 pages for 'long integer'.

Page 482/832 | < Previous Page | 478 479 480 481 482 483 484 485 486 487 488 489  | Next Page >

• Windows 7 64bit keyboard issues

  - by Scott

  I have a Pavilion dv4 notebook running Windows 7 64bit Enterprise edition. This morning I started to notice some really strange behavior in how it handled its built-in keyboard. At random intervals there will be a long delay in key presses, to which some keys will never show and other keys will continue to repeat until you hit the backspace. Other keys get mapped incorrectly to other keys. If I hook up an external keyboard the problem does not appear. Before I reformat the machine and do a fresh install, I thought I would check here to see if anyone has experienced this same issue and if so, how did you fix it?

  Read the article

• Ubuntu Wireless not working on Lenovo t400

  - by VmaxBoss

  This problem started after upgrading to 12.04, an my system is 'up2date' Have tried most of the solution-proposals found on the net. lspci -nnk | grep -iA2 net 00:19.0 Ethernet controller [0200]: Intel Corporation 82567LF Gigabit Network Connection [8086:10bf] (rev 03) Subsystem: Lenovo Device [17aa:20ee] Kernel driver in use: e1000e 03:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection [8086:4237] Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1211] Kernel driver in use: iwlagn iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11abgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off sudo lshw -C network *-network description: Ethernet interface product: 82567LF Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 03 serial: 00:22:68:1a:c4:75 size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.0.2-k2 duplex=full firmware=1.8-3 ip=192.168.2.154 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:29 memory:fc000000-fc01ffff memory:fc024000-fc024fff ioport:1820(size=32) *-network DISABLED description: Wireless interface product: PRO/Wireless 5100 AGN [Shiloh] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 00:26:c6:6c:2d:24 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn latency=0 multicast=yes wireless=IEEE 802.11abgn resources: irq:30 memory:f4300000-f4301fff Please help Br/VB

  Read the article

• colliding btRigidBody objects behave strangely when moving slowly

  - by Piku

  I'm trying to use Bullet Physics in my iOS game. The engine appears to be correctly compiled in that the demos work fine. In my game I have the player's ship and some enemy ships. They're defined as btRigidBody objects and btCollisionObjects and I'm using btSphereShapes for collision. At 'fast' speeds, collisions appear to happen sensibly - things collide and nothing goes 'weird'. If the speeds are very slow though and the player's ship touches a non-moving object the collision happens, but then the player's ship moves at incredible speed over the next few frames and appears a long distance from where it collided - completely out of proportion to the speed it was moving before impact. To move the things around I'm using setLinearVelocity() each frame, ticking the physics engine, then using getMotionState() to update the rendering code I have. Part of the issue might be I don't quite understand how to set the correct mass or what the best speeds are to use for anything. I'm mostly sticking numbers in and seeing what happens. Should I be using Bullet in this way, and are there any guidelines for deciding on the mass of objects? (am I right in assuming that in collisions heavier objects will force lighter objects to move more)

  Read the article

• How do you limit the bandwidth for a file copy?

  - by wizard

  I've got an old windows 2000 box in a remote location with a T1 connection and a vpn to my location. I normally use smb mounts to transfer files but now it's time to decommission the server and copy it's backups to my location. I have about 40 gigabytes (compressed) to copy. I'm prepared for it to take a long time, but I have a few caveats. I need to limit the bandwidth so terminal service connections to the site are not affected I want to be able to resume a partial transfer There are a few small files and several large files (10-20 gigabytes). I'm familiar with rsync on *nix platforms but have had bad luck with windows and I don't know that it will really keep partially transfered files. What do you use?

  Read the article

• Multiple EyeFinity Display groups

  - by Shinrai

  Is it possible with an EyeFinity enabled card to make multiple display groups at once? I was playing with a FirePro 2460 and while a 4x1 or 2x2 display group works quite nicely, if I make a 2x1 display group and then select one of the other displays to try to make a second 2x1 display group, it disables the first one. Is there any way to circumvent this behavior and set up two separate spans on the same card? Additionally, can you set up distinct display groups if they're on different cards? I will have the opportunity to test several of these cards in one machine very shortly, but I'm curious if anyone has any experience. EDIT: I can confirm that you can make multiple spans on multiple cards (as long as they don't cross cards, obviously) (If the answers are different for FirePro/FireMV cards and Radeon cards, that is helpful and relevant knowledge - I doubt it, though.)

  Read the article

• Best cloud based IT Systems management services out there?

  - by Ryk

  Our startup organisation is growing fast in 2 different office locations. That brings new challenges and headaches. Our entire company is cloud based, and I am looking for a good product to manage our remote systems. Currently we do not have on-site AD servers, we are using the Windows Azure AD services, so cannot rely on group policies at this stage. I would like to be able to achieve the following: (they are all laptops) Remote Desktop Support Patch management Lock down software on machines (restrict them) Monitor and manage systems Other benefits would be good, but if I can achieve the ones listed above, it will go a long way. We have a combination of Windows 7 pro & Windows 8 & 8.1 machines. I am currently using Windows Intune, but it is really limited. Really just a glorified patch enforcer. Thank you in advance to your help.

  Read the article

• CNAME lookup failed temporarily. (#4.4.3)

  - by klickverbot

  A friend of mine just told me that he can't send mails to accounts on one of my servers via the SMTP server provided by his ISP. The error message in the bounce he gets reads: Hi. This is the qmail-send program at aon.at. I'm afraid I wasn't able to deliver your message to the following addresses. This is a permanent error; I've given up. Sorry it didn't work out. <[email protected]>: CNAME lookup failed temporarily. (#4.4.3) I'm not going to try again; this message has been in the queue too long. Any ideas what could be the reason for this? I have double-checked the DNS records for my domain, but they seem perfectly fine, and from any other mail servers I tested, delivery works flawlessly…

  Read the article

• Why might one hard disk perform slower than another?

  - by Styne666

  I have just bought two WD 3TB Reds (WD30EFRX) for a FreeNAS box and whilst doing burn-in testing it seems like one is consistently taking about 10% longer than the other. So far I've done: a dd read test of the whole device, a long SMART test and it's currently halfway through a badblocks -wvs. The second device is lagging behind the first on all of them. I'm running these commands on Debian stable in two Konsole tabs. Is there a reason this could be considered normal behaviour or is it worth running the tests independantly? They're both plugged in to the LSI 2308 (IT mode) on a Supermicro X10SL7-F.

  Read the article

• Tool to create unscaled call-out from a thumbnail image?

  - by Mal Ross

  I'm creating an online tutorial for some software and need to include screenshots. In particular, I want to highlight the position and appearance of a given control in a large screen. Given that I haven't got the space to show the screen at full resolution (at least, not alongside the tutorial text), I figured I would use a kind of call-out from a thumbnail. Here's my poor first effort, made in Paint.NET: Given how long this took me to craft, I'd really like to find a tool to speed things up (and make them look a little more professional!). Preferably a free one, too - or one that has a downloadable trial. The exact style it produces isn't that important, provided it achieves the desired effect. Can anyone help me out? Thanks, Mal. P.S. I'm using Windows Vista.

  Read the article

• Release Notes for 3/8/2012

  Here are the notes for today’s release: Clarified the purpose of the fork name when creating a fork of a project. Added confirmation messages to deletion of system requirements when editing documentation. Deployed several bug fixes: Fixed an issue that was causing AppHarbor build notifications to fail. Thanks to claq2 for the bug report! Fixed several issues where extremely long titles or descriptions on items on the issues, discussions, profiles, and home pages would not wrap properly. Fixed a minor wrapping issue around the link to upload patches. Fixed an issue with viewing RSS feeds in Internet Explorer. Fixed an issue where replying to a discussion with a quote would push the content past the page margins. Have ideas on how to improve CodePlex? Visit our ideas page! Vote for your favorite ideas or submit a new one. Got Twitter? Follow us and keep apprised of the latest releases and service status at @codeplex.

  Read the article

• Ubuntu 12.10 and nVidia drivers don't like each other?

  - by mingos

  I decided to upgrade both my computers from Precise to Quantal. What a mistake that was. My laptop has a nVidia GT 330M card, while the desktop has an nVidia 9600 GT. In both cases everything goes great as long as I use the Nouveau driver (ugh!). Can't really play games (Amnesia... and hoping for Steam Beta participation...), even though it's OK for work. Now, ever since 9.04 or so, I just installed nvidia-current and all just worked. Since 12.10, after installing nVidia drivers, Unity won't start at all (hangs with only the wallpaper displayed, no cursor or widgets), Gnome Shell is permanently in fallback mode. Now, I have tried on both computers, with multiple clean installs on Ubuntu (two separate downloads, just in case), one from Ubuntu Gnome Remix. And additionally, Fedora 17, which seems to suffer from the same issue. Tried all nVidia driver suggestions available in Software Sources, and even compiled the drivers myself. I tried several versions of the driver to exclude an issue with the newest one. In my frustration, I have switched to Windows (which, ironically, "just works" with my hardware), but still hold a twin OS configuration on the desktop and would like to use Ubuntu again. So, can anyone point me to where the issue might lie?

  Read the article

• How to temporarily disable SonicWall from connecting to the internet?

  - by Jerry Dodge

  I have been doing some extensive seeking in our SonicWall TZ-215 for the source(s) of unnecessary internet traffic, as we have issues with excessive traffic. As part of my research, I need to watch the Connections Monitor, which lists me all the current connections. This list becomes quite long, with 40+ devices on the network, it's tough to pinpoint the main causes. What I would like to do is disable the SonicWall its self from letting its internal components from connecting to anything. Is there any type of trick I can do in the Firewall which can prevent the router system from connecting to anything, to clean up the connections monitor and allow only suspicious traffic?

  Read the article

• How to "get" a reliable parallel port on a laptop without a PCMCIA slot?

  - by ldigas

  Usb-Parallel port (for an old, but reliable matrix printer that has its special use) connections (cables) are unreliable. They sometimes work, sometimes don't - and since I installed Windows 7 I can't get neither of my old ones to work properly. PCMCIA is usually considered (and it is) a much more reliable solution, but unfortunatelly, none of my new laptops has a PCMCIA slot. So, all ideas are welcomed. What should I do? I'm open to all suggestions as long as you have some experience that they work more reliably than USB-Parallel cables and their wicked drivers.

  Read the article

• XP Clients can't copy to networkshare

  - by chewbacca76

  i have a windows 2003 domain where i have strange problem. One of our file shares is on a 2003r2 domain controller, xp clients trying to copy files on the share are always getting the error error copying file or folder filename could not be copied. path too long while windows 7 clients work fine. Nothing unusal is found in the eventlog on both the server and the client. It doesn't matter if i access the share by fqdn or ip, the path is including filename shorter than 20 characters i.e. \path\share\file.txt Copying files to other servers is fine. Reading from the shares is ok too. Happened from one day to the other, one windows update that was installed this day (kb2736233) was removed but nothing changed. thanks for any tips

  Read the article

• Previous Versions delayed with SBS 2008 / Windows 7

  - by indeed005

  The SBS 2008 at this site has Previous Versions enabled on a mapped drive. The snapshots happen 3 times a day. I doubt they take very long; the diff size is only a few GB. The problem is that the users on Windows 7 cannot see their previous versions until a few hours later. Is there some indexing that has to happen before the Previous Versions are visible to the client machines? Edit: In the application log, 3 minutes after every scheduled backup, there is an event for VSS (EventID 8224) saying "The VSS service is shutting down due to idle timeout" Apparently this means it has finished successfully, even though modified files still do not show another version.

  Read the article

• Deploy multiple django instances on one Host [migrated]

  - by tvn

  I am trying to setup multiple Django instances on one Host with lighttpd. My problem is to get Djangos FCGI working on subdirectories served by my Webserver. So my aim is the following: www.myhost.org/django0 - django1.fcgi on localhost:3000 www.myhost.org/django1 - django2.fcgi on localhost:3001 www.myhost.org/django2 - django3.fcgi on localhost:3002 Unfortunately the following configuration doesn't even work for one: $HTTP["url"] =~ "^/django0/static($|/)" { server.document-root = "/home/django0/django/static/" } $HTTP["url"] =~ "^/django0/media($|/)" { server.document-root = "/usr/lib/python2.7/dist-packages/django/contrib/admin/media/" } $HTTP["url"] =~ "^/django0($|/)" { proxy.server = ( "" => ( ( "host" => "127.0.0.1", "port" => "3001", "check-local" => "disable", ) ) ) } The only response I get is an 404 and even this takes a long time till I get this. I found nothing suspicious neither in the access.log nor in the error.log.

  Read the article

• Spammers sending out from an inactive domain

  - by YesIWillFixYourEmailSigh

  We have a shared hosting service running QMail and Plesk. One of our inactive clients was left active in the system by mistake, and spammers found their very weak passwords and sent out a massive barrage of messages before we caught the problem and shut off the services for that domain. My question is this: How did they get access to that domain in the first place? The client is long-gone and the domain/DNS is not pointing at our server at all, and neither is the MX record. So how were they able to find that domain and exploit it when nothing on the "outside" was pointing to it?

  Read the article

• Searching Multiple Terms

  - by nevets1219

  I know that grep -E 'termA|termB' files allows me to search multiple files for termA OR termB. What I would like to do instead is search for termA AND termB. They do not have to be on the same line as long as the two terms exists within the same file. Essentially a "search within result" feature. I know I can pipe the results of one grep into another but that seems slow when going over many files. grep -l "termA" * | xargs grep -l "termB" | xargs grep -E -H -n --color "termA|termB" Hopefully the above isn't the only way to do this. It would be extra nice if this could work on Windows (have cygwin) and Linux. I don't mind installing a tool to perform this task.

  Read the article

• Nvidia driver on Windows 7 causing black screen

  - by inKit

  I have just installed Windows 7 on a desktop machine and for the first time ever have had a really tough time doing so, its normally a nice smooth install. This time I found that the monitor would simply go black after completing the installation. I tried reinstalling about 3 times and this did not help. After much searching I discovered that it was the nvidia drivers that were playing up with win 7, so i booted into safe mode, disabled the device, then rebooted to complete the installation. Windows 7 now works fine as long as the nvidia 9600 gt video card is disabled. The moment I enable it, the system requires a reboot and the screen will go black before even getting to the log in screen. I have tried downloading the latest driver and installing it manually, I have also tried uninstalling the device and allowing windows 7 to install it itself. Nothing seems to work. any clues?

  Read the article

• Our company has 100,000s+ photos, how to store and browse/find these efficiently?

  - by tobefound

  We currently store our photos in a structure like this: folder\1\10000 - 19999.JPG|ORF|TIF (10 000 files) folder\2\20000 - 29999.JPG|ORF|TIF (10 000 files) etc... They are stored on 4 different 2TB D-link NASes attached and shared on our office network (\\nas1, \\nas2, and so on...) Problems: 1) When a client (Windows only, Vista and 7) wishes to browse the let's say \\nas1\folder\1\ folder, performance is quite poor. A problem. List takes a long time to generate in explorer window. Even with icons turned off. 2) Initial access to the NAS itself is sometimes slow. Problem. SAN disks too expensive for us. Even with iSCSI interface/switch technology. I've read a lot of tech pages saying that storing 100 000+ files in one single folder shouldn't be a problem. But we don't dare go there now that we experience problems on a 10K level. All input greatly appreciated, /T

  Read the article

• Making a Linux laptop flight-safe; disabling wireless/radio

  - by SpoonMeiser

  I'm going on a long flight tomorrow, and would like to be able to use my laptop during the journey. Wireless devices like WiFi and bluetooth interfere with airplanes instruments, and shouldn't be used on flights. If my laptop does not have a physical rf-kill switch, is it sufficient to just ensure that the relevant modules do not get loaded? If so, is that always safe, or does it vary between different hardware? My particular situation, is a Samsung NC10 netbook. Atheros 5k wireless hardware. Debian sid with kernel 2.6.30-1-686. However, I think it'd be interesting to know the answer to this question for the general case; not just my specific case.

  Read the article

• Default profile for large

  - by user63434

  Hi I am setting up a master image to clone to all same machine type Windows 7 client, I login as administrastor and installed all the programs and changed the desktop settings etc, but my local administrator profile is 244megs in size, which will become the default profile of the local machine when sysprep, we have a 2003 server that I want to use mandatory profile for all login users which means I need to copy this profile to the server so when any users login to the domain they are using this profile, loading a 244megs profile is going to be very slow since it will be removed from the client when they logoff. So next time they login it will take a long time again. Is there anything I can do, can I just copy just the bare minimum files from the default profile to the server, as I am not sure what parts I need, I read that I must copy my documents, my documents/pictures so the folder redirection will work. What else do I need to copy to the server? I have firefox xmark sync also and MS words etc. THanks

  Read the article

• HyperV management through Windows 8

  - by Snake

  Consider the following setup: 1 Hypervisor 3 Clients (Server 2012 with AD, Server 2012, Windows 8). Now we can remote desktop into the Hypervisor and manage the VMs with the manager. This also works from the Server 2012 (I installed the manager there). But it doesn't work from the Windows 8 machine. All machines are in the same domain. Am I forgetting something? I followed this long page http://technet.microsoft.com/en-us/library/cc794756(v=ws.10).aspx But I find it so weird that it works for the same user on Windows Server 2012, but not on Windows 8.

  Read the article

• Remote Linux system via Windows 7

  - by kaila

  I have a dual boot with Windows 7 and Fedora. Though I can long into both without any problems, I am trying to log in to the linux account via the Windows account. Is that possible? Or, is it possible to access my university's linux server via telnet from home? I did so and got an error, with cold not connect to port 23 message. Also, since most of my mail accounts are on Windows, the passwords to which I have forgotten, I would prefer working on a ;remote' connection.

  Read the article

• Reliance on the compiler

  - by koan

  I've been programming in C and C++ for some time, although I would say I'm far from being expert. For some time I've been using various strategies to develop my code such as unit tests, test driven design, code reviews and so on. When I wrote my first programs in BASIC I typed in long listings before finding they would not run and they were a nightmare to debug. So I learnt to write a small bit and then test it. These days I often find myself repeatedly writing a small bit of code then using the compiler to find all the mistakes. That's OK if it picks up a typo but when you start adjusting the parameters types etc just to make it compile you can screw up the design. It also seems that the compiler is creeping into the design process when it should only be used for checking syntax. There's a danger here of over reliance on the compiler to make my programs better. Are there better strategies than this ? I vaguely remember some time ago an article on a company developing a type of C compiler where an extra header file also specified the prototypes. The idea was that inconsistencies in the API definition would be easier to catch if you had to define it twice in different ways.

  Read the article

< Previous Page | 478 479 480 481 482 483 484 485 486 487 488 489  | Next Page >