Search Results

Search found 15087 results on 604 pages for 'native mode'.

Page 484/604 | < Previous Page | 480 481 482 483 484 485 486 487 488 489 490 491  | Next Page >

• SBS 2003 boot stalls at acpitabl.dat

  - by John

  I have a SBS 2003 server running for 3 year without any problems, and few days ago it freezes during the boot. System is using two 500 Gb drives in RAID1 (Intel Matrix 7.5) After trying to load in safe mode, boot stops on acpitabl.dat. First idea was that there is a problem with RAID altough disk status was OK, and RAID status was Rebuild. I tried to boot with each drive, and one gives me the same problem, and the other drive is failing to load. Took both drives out, and checked it on a different machine. One drive is dead, other is without any problems. Returned the good drive back in SBS 2003 with changed status to Degraded, but the problem is still the same. I also have a clean SBS 2003 copy installed on this drive (previous installation), which loads smooth and quick. So, I believe the main problem is this installed version of SBS 2003. Did not make any hardware changes, did not make any updates (not sure about any automatic windows updates lately). Since there are tons posts about this problem, and no clear solution, I am trying to figure how to repair SBS 2003 installation, since there are some installed programs on this installation which I cannot re-install without additional issues.

  Read the article

• VirtualBox VM running web server not accessible via external IP

  - by mwigdahl

  I have a Windows 7 machine running VirtualBox with an Ubuntu guest. The guest has a Bitnami LAMP stack installed. I have the guest configured for Bridged networking, and I can access the guest web server just fine from other machines on my LAN using the guest's IP. I'm trying to configure port forwarding so that I can access the web server from outside my LAN. (The router is a 2WIRE model as I'm on ATT's UVerse). I've set up port forwarding for ports 80 and 443 to the guest's IP in a similar manner to how I had them set up for my previous, physical web server, which worked just fine. However, I cannot seem to access the new, virtual web server using my external IP on the forwarded port. I suspected Windows Firewall issues on the host, but disabling it didn't solve the issue. Anyone have advice on what I should try next? EDIT: I've now attempted disabling the firewall on the guest with sudo ufw disable -- that doesn't seem to help either. However, after checking the router's port forwarding in more detail I may see the problem. My VM is named "linux" and in the router's configuration pages it shows up inconsistently. Sometimes it reports with a valid LAN IP and other times it doesn't show up with any IP. Even when it shows the correct IP the router indicates that it is disconnected. Could this be an indication that the 2WIRE router doesn't play well with VirtualBox's bridged networking mode?

  Read the article

• Why is Apache htdigest authentication failing in IE10 on Windows 8?

  - by Kevin Fodness

  One of our developers reported that for the past week or two, the htdigest authentication that we have set up on our test sites in Apache is not working in IE10 on Windows 8. It's fine on IE10 on Windows 7, and it's fine on Chrome on Windows 8. The specific behavior is: Navigate to site with htdigest authentication enabled, username and password form pops up, enter correct username and password, and the username and password box pops up again. Potentially useful information: All patches applied on Windows 8 box No additional software on Windows 8 box other than Outlook 2013 and a browser test suite (Chrome, Firefox, Opera, Chrome Canary, Opera Next) Win8 running in a virtual machine on Xen Same behavior can be replicated on Win8/IE10 on Browserstack.com Server running Ubuntu 10.10 with Apache 2.2.16 This feels like a patch was applied to the Windows box that broke digest authentication for IE10 on Win8 (box configured for automatic updates). However, without knowing a specific date I can't necessarily nail this down. Has anyone else experienced this problem? EDIT: This problem only happens in the "Metro" interface, not when running IE10 in desktop mode. As of a few weeks ago, it worked fine even in the "Metro" interface.

  Read the article

• Windows 7 fails to connect to the internet a few minutes after startup

  - by SageTheGreat

  Problem Earlier today, when I turned on my desktop computer, my internet connection works fine. Cryptocurrency miners connecting and hashing as usual and I can browse websites. But after a few minutes, my miner fails indicating that there is something wrong with my internet connection. Tried refreshing my browser and is stuck at "resolving host", and then presented me an error. After that, i can't browse sites anymore. But the weird thing is that the network icon in Windows 7 shows no signs of problems. Solutions Made Restarted my computer without doing anything: Problem persists. Tried using the network troubleshooter of windows: Reported no problems Stopped bonjour still no progress. Loaded windows using Last good config: still no progress. Restarted Modem: No change. Current Status I currently did a system restore to my system to a point before installing the latest update from Microsoft. Because earlier today, I installed some updates and after that, the problem started to appear. (After system restore, same problem.) Latest Programs installed before the problem MS Visual Studio 2013 (but internet still worked fine after the install). I hope someone could provide answers on this problem. It is my first time encountering this. EDIT: Additional Info OS: Windows 7 SP1 64-bit AV: Avast Free Antivirus Internet Connection Type: Ethernet It appears that my Laptop can't even connect to the machine thru Remote Desktop My laptop and phone on WiFi works fine and can connect to the internet. EDIT 2: Whenever I boot into Safe Mode, my Internet is fine.

  Read the article

• Why Is Volume Shadow Copy Services stopping?

  - by David Mackintosh

  I am running Windows 7 Professional, 64-bit. I am running a backup-over-the-internet software client which depends on the Volume Shadow Copy Services running. Since I installed Service Pack 1 (or rather, didn't object when Windows Update forced Service Pack 1 on me) the backup service is failing to back everything up because VSC isn't running. Most of the time it fails to back up such noise as the Security Essentials database or the Messenger Live contact list -- stuff I really don't care about -- but I don't want to fall into the trap of accepting an Error-state backup as "normal". At the recommendation of the backup software, I have set the VSC service startup mode to be Automatic. When I look in the Event Log, System channel I can see at boot time: The Volume Shadow Copy service entered the running state. ...and then two or three minutes later: The Volume Shadow Copy service entered the stopped state. How do I figure out why VSC is stopping? At the suggestion of the backup vendor, I have already followed the suggestions from http://support.microsoft.com/default.aspx/kb/940184 net stop SENS net stop EventSystem net start EventSystem net start SENS net stop COMSysApp net stop SwPrv net stop VSS cd /d C:\Windows\system32 regsvr32 ole32.dll /s regsvr32 oleaut32.dll /s regsvr32 vss_ps.dll /s vssvc /register /s regsvr32 /i swprv.dll /s regsvr32 /i eventcls.dll /s regsvr32 es.dll /s regsvr32 stdprov.dll /s regsvr32 vssui.dll /s regsvr32 msxml.dll /s regsvr32 msxml3.dll /s regsvr32 msxml4.dll /s net start SwPrv net start VSS net start ProtectedStorage ...and per http://support.microsoft.com/kb/940184 I have deleted the key tree HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\EventSystem\{26c409cc-ae86-11d1-b616-00805fc79216}\Subscriptions I have also run chkdsk /F and chkdsk /R on both permanent hard disks. (I had a similar problem with another computer (same OS, same failure, same start point after SP1 install) but the problem went away when I forced Volume Shadow Copy Services to Automatic startup rather than Manual. I did not have to resort to following the Microsoft KB instructions.)

  Read the article

• WEP/WPA/WPA2 and wifi sniffing

  - by jcea

  Hi, I know that WEP traffic can be "sniffed" by any user of the WIFI. I know that WPA/WPA2 traffic is encrypted using a different link key for each user, so they can't sniff traffic... unless they capture the initial handshake. If you are using a PSK (preshared key) schema, then you recover the link key trivially from this initial handshake. If you don't know the PSK, you can capture the handshake and try to crack the PSK by bruteforce offline. Is my understanding correct so far?. I know that WPA2 has AES mode and can use "secure" tokens like X.509 certificates and such, and it is said to be secure against sniffing because capturing the handshake doesn't help you. So, is WPA2+AES secure (so far) against sniffing, and how it actually works?. That is, how is the (random) link key negociated?. When using X.509 certificates or a (private and personal) passphrase. Do WPA/WPA2 have other sniffer-secure modes beside WPA2+AES? How is broadcast traffic managed to be received by all the WIFI users, if each has a different link key?. Thanks in advance! :).

  Read the article

• Dovecot authentification not working

  - by user1488723

  I run a Ubuntu 10.04 VPS with Postfix and Dovecot installed. For a while I had problems with the mailserver itself (Postfix) but now it runs ok. I can telnet into it from localhost (telnet localhost 25 while logged in) and Im blocked if I try to do it from the outside (telnet mail.example.org 25). This is as it should be according to my main.cf However when I try to log in using Dovecot (openssl s_client -connect mail.example.com:993) I'm allowed in but denied when trying to identify myself as a user: Excerpt from Dovecot log in: Key-Arg : None Start Time: 1341074622 Timeout : 300 (sec) Verify return code: 18 (self signed certificate) OK [CAPABILITY IMAP4rev1 LITERAL+ SASL-IR LOGIN-REFERRALS ID ENABLE AUTH=PLAIN AUTH=LOGIN] Dovecot ready. When I continue and try to log in to a specific user with the command: A001 login user password I get: A001 NO [AUTHENTICATIONFAILED] Authentication failed. I've reset the password to ensure it is correct and I know the user (user) exists on the system. When I do /etc/init.d/dovecot reload I get: /etc/init.d/dovecot: 29: maildir:~/Maildir: not found * Reloading IMAP/POP3 mail server dovecot [ OK ] Could it be that the mailboxes isn't found? Postfix main.cf: home_mailbox = Maildir/ mailbox_command = recipient_delimiter = + inet_interfaces = all smtpd_use_tls = yes smtpd_tls_auth_only = no smtpd_tls_loglevel = 1 smtpd_tls_cert_file = /etc/postfix/ssl/smtpd.crt smtpd_tls_key_file = /etc/postfix/ssl/smtpd.key smtpd_tls_CAfile = /etc/postfix/ssl/cacert.pem smtpd_sasl_auth_enable = yes smtpd_client_restrictions = permit_sasl_authenticated, permit_mynetworks, reject_unauth_destination smtpd_sender_restrictions = permit_sasl_authenticated, permit_mynetworks smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination broken_sasl_auth_clients = yes smtpd_sasl_type = dovecot smtpd_sasl_path = private/auth smtpd_sasl_security_options = noanonymous smtpd_sasl_local_domain = $mydomain Dovecot.conf: protocols = imap imaps disable_plaintext_auth = no log_timestamp = "%b %d %H:%M:%S " ssl = yes ssl_cert_file = /etc/postfix/ssl/smtpd.crt ssl_key_file = /etc/postfix/ssl/smtpd.key mail_location = maildir:~/Maildir auth_verbose = yes mail_access_groups = mail auth_username_chars = abcdefghijklmnopqrstuvwxyz0123456789 protocol imap { imap_client_workarounds = delay-newmail tb-extra-mailbox-sep } auth default { mechanisms = plain login passdb pam { } userdb passwd { } socket listen { client { path = /var/spool/postfix/private/auth user = postfix group = postfix mode = 0660 } } }

  Read the article

• Why java -version returning a different version than the one defined in JAVA_HOME?

  - by Shekhar

  I am trying to set JAVA_HOME in Ubuntu OS. I have copied jdk 1.7 in /usr/lib/jvm and set JAVA_HOME in /etc/profile file. Contents of /usr/lib/jvm folder are as follows : shekhar@ubuntu:~$ ls /usr/lib/jvm/ default-java java-1.6.0-openjdk java-6-openjdk java-6-openjdk-i386 jdk1.7.0_01 java-1.5.0-gcj-4.6 java-1.6.0-openjdk-i386 java-6-openjdk-common java-7-openjdk-i386 and last few lines of /etc/profile file are as follows : export JAVA_HOME=/usr/lib/jvm/jdk1.7.0_01 export PATH=$PATH:$JAVA_HOME/bin After finishing all this when I run java -version command I get following output : shekhar@ubuntu:~$ java -version java version "1.6.0_24" OpenJDK Runtime Environment (IcedTea6 1.11.4) (6b24-1.11.4-1ubuntu0.12.04.1) OpenJDK Server VM (build 20.0-b12, mixed mode) and when I run ls -lah command I get following output : shekhar@ubuntu:~$ ls -lah /usr/bin/java lrwxrwxrwx 1 root root 22 Sep 29 09:58 /usr/bin/java -> /etc/alternatives/java shekhar@ubuntu:~$ ls -lah /etc/alternatives/java lrwxrwxrwx 1 root root 45 Sep 29 09:58 /etc/alternatives/java -> /usr/lib/jvm/java-6-openjdk-i386/jre/bin/java Can anyone please tell me which thing I am missing? Why Ubuntu is still pointing to open jdk and not to my jdk 7? PS : I have seen this similar question and its answers but that question is related to Windows OS and not for Ubuntu so I am reposting this similar question for Ubuntu.

  Read the article

• Iptables QUEUE Target and Snort

  - by bradlis7

  I'm trying to set up a firewall with support for snort, and it is dropping all of my packets when I add the QUEUE target. I've made it like this, but the QUEUE target is not allowing the packets to be processed any further: -A INPUT -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -j QUEUE -A INPUT -j ACCEPT # It's not allowing anything past QUEUE, as you can see below in the count. > iptables -I INPUT -nv pkts bytes target prot opt in out source destination 6707 395K ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 933 138K QUEUE all -- * * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 I'm eventually going to change it to forward, but I'm just trying to get it working for now. I start snort like so: snort -Q -D -c /etc/snort/snort.conf EDIT: More Information When I run it, it still sees the packets without having an iptables QUEUE target rule, but when I add a QUEUE target, it starts losing all of my packets. # snort -Qc /etc/snort/snort.conf -N -A console Enabling inline operation Running in IDS mode --== Initializing Snort ==-- Initializing Output Plugins! Initializing Preprocessors! Initializing Plug-ins! Parsing Rules file "/etc/snort/snort.conf" ## === CUT === *** *** interface device lookup found: bond0 *** Initializing Network Interface bond0 Decoding Ethernet on interface bond0 ## === CUT === Not Using PCAP_FRAMES So, it says inline, but the it says it's using bond0. Inline should not require an interface, right?

  Read the article

• How To Investigate/Restore MySQL Permissions? MySQL ERROR 1045 (28000): Access denied for user

  - by Recc

  ERROR 1045 (28000): Access denied for user 'root'@'localhost' (using password: YES) Debian. mysqld is listening on 3306 supposedly Telnet to 3306 works Also tried binding it specifically yo localhost and then 127.0.0.1 which made no difference However: # netstat -ln | grep mysql unix 2 [ ACC ] STREAM LISTENING 78993 /var/run/mysqld/mysqld.sock # mysql -P3306 -ptest ERROR 1045 (28000): Access denied for user 'root'@'localhost' (using password: YES) Things I've tried: dpkg-reconfigure mysql-server-5.1 Doesn't help http://www.debian-administration.org/articles/442 Doesn't help This command (source): UPDATE mysql.user SET Password=PASSWORD('MyNewPass') WHERE User='root'; FLUSH PRIVILEGES; Doesn't help, in fact: Query OK, 0 rows affected (0.00 sec) Rows matched: 0 Changed: 0 Warnings: 0 So might the user be deleted? Extremely unlikely as all this started after packages update a colleague did and some separate services started screwing around but my colleague said he removed the offenders. Theres more: while # mysqld_safe --skip-grant-tables is running one can access the data tables, only with the valid passwords! So there's users and some authentication takes place hence the 0 rows affected above. Can the privileges tables be damaged somehow and how can I recreate/restore them when my only way of getting a mysql console is to skip them? Can I spare my reinstall of MySQL? Either way I did get a dump of the DBs now that I could get in with the above mode.

  Read the article

• Gnome-panel disappearance in Ubuntu 10.10

  - by jurchiks

  Just today, after about a week of somewhat normal running (I'm a total beginner in Linux and the level of amazingly stupid problems I encountered made me go nuts), today my panel disappeared (the one with Applications/System menus, you'd call it taskbar in Windows). Also, Alt+F2 doesn't work and Ctrl+Alt+Backspace has no effect (I'd think it's supposed to do something). I tried the solution posted here: Panel doesn't show at startup at Ubuntu 10.04 No luck, didn't change absolutely anything. I also couldn't find the .gconf and .gconfd folders using search, so couldn't try that option. There were ones that had same names but without the dot though, but there were several so I didn't risk. What could possibly be the reason for this? All I did yesterday was try to install some updates (another extremely dumb problem - doesn't allow to install even the official updates - "insecure sources" or smth like that, tried fixing it with some tutorials on the net but in the end it worked only for half a day and went back to refusal mode :@) and very few tools from the Ubuntu Software Center, but nothing that would change system settings just by installing it.

  Read the article

• What does this diagnostic output mean?

  - by ChrisF

  I recently had a fault with my broadband connection. It turned out to be a fault with the ISP's or teleco's equipment. My ISP posted this diagnostic, but while I understand it in general, I'd like to to know more about the details. I'm assuming that ATM means Asynchronous Transfer Mode and PPP means Point to Point Protocol. It was this that my router was indicating as the fault. xDSL Status Test Summary Sync Status: Circuit In Sync General Information NTE Status: NTE Power Status: Unknown Bypass Status: Upstream DSL Link Information Downstream DSL Link Information Loop Loss: 9.0 17.0 SNR Margin: 25 15 Errored Seconds: 0 0 HEC Errors: 0 Cell Count: 0 0 Speed: 448 8128 TAM Status: Successfully executed operation Network Test: Sub-Test Results Layer Name Value Status Modem pass Transmitter Power (Upstream) 12.4 dBm Transmitter Power (Downstream) 8.8 dBm Upstream psd -38 dBm/Hz Downstream psd -51 dBm/Hz DSL pass Equipment Vendor Name TSTC Equipment Vendor Id n/a Equipment Vendor Revision n/a Training Time 8 s Num Syncs 1 Upstream bit rate 448 kbps Downstream bit rate 8128 kbps Upstream maximum bit rate 1108 kbps Downstream maximum bit rate 11744 kbps Upstream Attenuation 3.5 dB Downstream Attenuation 0.0 dB Upstream Noise Margin 20.0 dB Downstream Noise Margin 19.0 dB Local CRC Errors 0 Remote CRC Errors 0 Up Data Path interleaved Down Data Path interleaved Standard Used G_DMT INP INP Upstream Symbols n/a INP Upstream Delay 4 ms INP Upstream Depth 4 INP Downstream Symbols n/a INP Downstream Delay 5 ms INP Downstream Depth 32 ATM Reason: No ATM cells received fail Number of cells transmitted 30 Number of cells received 0 number of Near end HEC errors 0 number of Far end HEC errors n/a PPP Reason: No response from peer fail PAP authentication nottested CHAP authentication nottested (I'm not sure that Super User is the best place to ask this, but two people have suggested I ask it here so here I am).

  Read the article

• Being a more attractive job candidate - Certs XOR Degree

  - by Zephyr Pellerin

  I'm currently working in an IT position, where I do helpdesk stuff, and predominantly security related issues/consulting (In the loosest sense of the term) In-House and for Service-Contract clients (as the only/acting CCSP [I guess I should say only person with Cisco experience] in my organization). I've professionally written Kernel Mode drivers for a gaming company. Among other things that I'm proud to put on a resume. I think of myself as very reasonably qualified as a System Administrator, With excellent Cisco experience, among other things I think would make a good addition to almost any IT staff in need of a new employee. However, Something has always tripped me up - Human Resources. Let me explain, I decided to skip the university route - I'm immensely glad that I did, The computer science graduates that I've met and work with rarely know much of anything about Computers (Until they gain some 'real' experience), Even when asked about Theoretical Computing fundamentals they can rattle something off about Turing Completeness but rarely do they understand the mathematical underpinnings. In short, I think instead of going to college, I'd rather pick up some real world experience. However, Apparently, Employers rarely think the same way. A quick perusal of jobs through the standard job search engine yields nothing short of a conspiracy to exclude anyone without 'A Bachelors Degree in Computer Science or Equivalent'. Interviews I've had in the past have almost always been entangled with - 1. My Age (Which I can't really change) and 2. Lack of Degree. Employers frequently disregard the CCNA/CCSP, The experience I've gained through internships, My extensive experience in x86 assembly and C, among so many other things I like to think are valuable to employers - In lieu of the fact that I don't have a piece of paper. So, AS AN EMPLOYER - Is it even worth working on my CCIE? Or should I pad my resume with certifications that are easier to acquire (Like CISSP, MSCE, Network+, etc.). Or should I ditch the whole idea and head back to get a Mathematics or CS degree?

  Read the article

• Can't connect to EC2 instance Permission denied (publickey)

  - by Assad Ullah

  I got this when I tried to connect my new instace (UBUNTU 12.01 EC2) with my newly generated key sh-3.2# ssh ec2-user@**** -v ****.pem OpenSSH_5.6p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug1: Applying options for * debug1: Connecting to **** [****] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /var/root/.ssh/id_rsa type -1 debug1: identity file /var/root/.ssh/id_rsa-cert type -1 debug1: identity file /var/root/.ssh/id_dsa type -1 debug1: identity file /var/root/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.9p1 Debian-5ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '****' is known and matches the RSA host key. debug1: Found key in /var/root/.ssh/known_hosts:4 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /var/root/.ssh/id_rsa debug1: Trying private key: /var/root/.ssh/id_dsa debug1: No more authentication methods to try.

  Read the article

• trying to figure out how to bridge two virtual networks together and in turn bridge that to the internet for a virtual inline IDS/IPS system

  - by Tony robinson

  I'm trying to figure out how to bridge two vmware (server or workstation, workstation) or virtualbox networks together with a linux IDS/IPS system transparently inline between both the virtual networks. How do I accomplish this? I understand how to bridge to virtual networks together, but how to I make the linux virtual machine sit between them and force traffic to go across the transparent bridge? I would like to have something along the lines of: vmnet a various vms host-only network ---- inline linux box vmnet a boxes forced to go through here to get to the internet --- vmnet b network with internet access configured as either NAT or bridged -- internet I know that basically the linux box needs two virtual nics, one on vmnet a and vmnet b, but other than that, I don't know how to force all the traffic to go across the "transparent" bridging linux box on its way to the internet. Do vmnet a and b have to be the same ip network with the same default route? does vmnet a not have a default route and vmnet b have a default route? I've read in vmware forums that on the linux host you need to change permissions on the vmnet files for promiscuous mode? is this true? how do you configure this scenario on a windows box?

  Read the article

• How to interpret iozone values

  - by Henno

  I ran a test to measure my I/O IOPS on Linux: iozone -s 4g -r 2k -r 4k -r 8k -r 16k -r 32k -O -b /tmp/results.xls iozone claims that output is in operations per second yet the numbers are too big for that to be plausible. I'm observing some 320 CMDs/s maximum on vmware esx console (esxtop, then v). File size set to 4194304 KB Record Size 2 KB Record Size 4 KB Record Size 8 KB Record Size 16 KB Record Size 32 KB OPS Mode. Output is in operations per second. Command line used: iozone -s 4g -r 2k -r 4k -r 8k -r 16k -r 32k -O -b tmpresults.xls Time Resolution = 0.000001 seconds. Processor cache size set to 1024 Kbytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride KB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 4194304 2 19025 5580 27581 29848 284 198 415 1103217 1498 18541 4340 24245 25618 4194304 4 15650 21942 18962 21068 252 1198 193 976164 1677 22802 23093 21089 21232 4194304 8 11121 11638 10273 10165 247 1196 202 625020^C The test ran for 15 hours before I pressed ^C. Is that ordinary expectation for such command line (dedicated 4 drive RAID10 LUN, 10k RPM SAS drives in EMC CX300)?

  Read the article

• Win7 System folder contains infinitely looping SYSTEM(!) directory

  - by Matt

  My Windows 7 Enterprise computer has been crashing fairly frequently recently, so I decided to boot up in safe mode and run the TrendMicro client I have installed. It froze about 10 minutes into the full system scan, so in the spirit of http://whathaveyoutried.com, I started scanning each folder individually. When I got to ProgramData, the AV failed with an uncaught exception. I then went down a level and tried scanning Application Data, which failed as well. Imagine my surprise when I open the folder just to see the same folder again! As far as I can tell, this folder loop continues indefinitely. (If you are trying to recreate this, keep in mind that ProgramData is a hidden folder.) I'm actually a bit concerned that these are system folders, as this is a brand-new computer with a clean installation. I guess I have three questions: Has anyone else seen/experienced this before? I'm running Win7 SP1. How do I fix this? I've run CHKDSK \F with no success (although it was incredibly slow). What are the ramifications of an infinitely recursive directory? Theoretically speaking, each link takes up memory, so shouldn't I have no space available on my hard drive? (I've got about 180GB left.) I noticed that the tree view on the left only shows the "linked folder" icon on the deeper folders--does this mean anything special? (I've circled the icons or lack thereof in red.) How can the OS even resolve this aberration? And above all, what would happen if I were to select "Expand all folders"??? :P Matt

  Read the article

• MySQL Config on Large Machine

  - by Jonathon

  We have a Windows 2003 Enterprise Edition server (64bit) running only MySQL 5.1.45 64-bit. It has 16G RAM and 10T of hard-drive space in RAID 10. We are having horrible performance from mysqld (85-100% CPU utilization). We were running a smaller machine with better performance, so I am assuming our my.ini file is not correct for our current machine. The my.ini file is as follows: [client] port=3306 [mysql] default-character-set=latin1 [mysqld] port=3306 basedir="D:/MySQL/" datadir="D:/MySQL/data" default-character-set=latin1 default-storage-engine=MYISAM sql-mode="" skip-innodb skip-locking max_allowed_packet = 1M max_connections=800 myisam_max_sort_file_size=5G myisam_sort_buffer_size=500M table_open_cache = 512 table_cache=8000 tmp_table_size=30M query_cache_size=50M thread_cache_size=128 key_buffer_size=3072M read_buffer_size=2M read_rnd_buffer_size=16M sort_buffer_size=2M #replication settings (this is the master) log-bin=log server-id = 1 Does anyone see anything wrong with this setup? For a machine with this much RAM, why in the world would mysqld eat up so much CPU? I know we can optimize some queries, etc., but it did run okay on a smaller machine, so I am pretty sure it is the config. Thanks in advance for any help.

  Read the article

• Windows 7 doesn't start anymore

  - by martani_net

  Hi, I've experienced some BSOD on windows 7 RC, and some freezing when startup, but today was big surprise, it doesn't start anymore. I tried to start on safe mode and no results too, it shows the starting animation, then a blue screen for less than a second and turns off immediately. The only thing I remember did today is update flash player under Firefox, then chrome stopped working even after logging off, and once restarting, it doesn't start anymore. Anyone experienced the same issue? any hints? [EDIT 3] Solved : Windows 7 have a very smart repair strategy, it works automatically, and it tried every possible fix, what fixed my problem was the system restore to a previous date, all this happened automatically. [EDIT2] these are the last lines in the ntbtlog.txt file Did not load driver \SystemRoot\System32\drivers\vga.sys Loaded driver \SystemRoot\System32\Drivers\NDProxy.SYS Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS Loaded driver \SystemRoot\system32\drivers\CHDRT32.sys Loaded driver \SystemRoot\system32\DRIVERS\VSTAZL3.SYS Loaded driver \SystemRoot\system32\DRIVERS\VSTDPV3.SYS Loaded driver \SystemRoot\system32\DRIVERS\VSTCNXT3.SYS Loaded driver \SystemRoot\system32\drivers\modem.sys Loaded driver \SystemRoot\system32\DRIVERS\usbccgp.sys Loaded driver \SystemRoot\System32\Drivers\usbvideo.sys [edit] this is the BSOD I get : http://twitpic.com/i87cx Thank you.

  Read the article

• Slow Local Network, Windows 7, Snow Leopard, WiFi/Wired

  - by WerkkreW

  Hello - I am experiencing really poor local network performance in my home. I was recently using a Linksys WRT54G Router with DD-WRT on it, and a couple comparable Linksys-G PCI cards for connectivity but decided to upgrade hoping it would help with my performance issues. The computers in my house are connected as follows: Comcast Business Class Commercial 25mbps/10mbps (Verified with SpeakEasy and Speedtest.net) D-Link DGL-4500 Wireless N Router Windows 7x64 - D-Link DWA-552 Wireless-N Windows 7x64 - D-Link DWA-552 Wireless-N Mac Mini 10.6.2 - AirPort Extreme N Playstation 3, Hard Wired Xbox 360, Hard Wired Essentially the problem is very specific. Web browsing and uploading/downloading files from the internet is fine, more than fine. But if I want to say, Stream a video from one of my Windows 7 computers to my PS3, or copy a large video file between either of the PC's or the Mac, I get a consistent 500-900Kbps throughput at the high end. If I open my network browser, or try to browse my homegroup the response time is horrible. Both of my Windows computers are showing Strong wireless signals with a connection speed of 300Mbps. I know I can never expect to achieve anything near those speeds, but 500Kbps? Here is what I have tried so far: Enabled Single mode N-only and N/G Only on router WPA2 with AES Encrpytion Disabled "Remote Differential Compression" in Windows 7 Disabled TCP "Auto-Tuning" Used other software for file copies such as "Teracopy" I am at the end of my rope. Unfortunately I live in a 75 year old home with plaster walls, so hard-wiring my entire house isn't really an option I can handle right now. Any ideas to help me get decent speed when transferring files across my network would be greatly appreciated.

  Read the article

• Utility to grant admin rights to a user in Windows XP for few hours/days?

  - by user15660

  Hi, I have two accounts on my windows xp home desktop. The default regular user is used for everything and the 2nd user which has admin rights is used only for installations. I do this to avoid malware infestations during web browsing and limited user account is guarding against online threats to a good extend but many programs refuse to run under limited rights like revo uninstaller. many installs i run from limited user by selectin "run as" from right click context menu of the .exe file. but some apps need admin rights for certain. I use "switch user" to go to admin mode and do the install/uninstall. but the admin user has none of my preferences bookmarks setup nor has my locate32 indexing done and ready for fast search Is there a utility which I can use "run as" login in administration login and use that to grant my limited user admin rights for a limited amount of period like few hours or days? Please help. I guess MS might have closed many doors of it for fear of exploitation of the API. are there any?

  Read the article

• mysqld crashes on any statement

  - by ??iu

  I restarted my slave to change configuration settings to skip reverse hostname lookup on connecting and to enable the slow query log. I edited /etc/my.cnf making only these changes, then restarted mysqld with /etc/init.d/mysql restart All appeared to be well but when I connect to msyqld remotely or locally though it connects okay a slight problem is that mysqld crashes whenever you try to issue any kind of statement. The client looks like: Reading table information for completion of table and column names You can turn off this feature to get a quicker startup with -A Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 3 Server version: 5.1.31-1ubuntu2-log Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> show tables; ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... Connection id: 1 Current database: mydb ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... ERROR 2003 (HY000): Can't connect to MySQL server on 'xx.xx.xx.xx' (61) ERROR: Can't connect to the server ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... ERROR 2003 (HY000): Can't connect to MySQL server on 'xx.xx.xx.xx' (61) ERROR: Can't connect to the server ERROR 2006 (HY000): MySQL server has gone away Bus error The mysqld error log looks like: 101210 16:35:51 InnoDB: Error: (1500) Couldn't read the MAX(job_id) autoinc value from the index (PRIMARY). 101210 16:35:51 InnoDB: Assertion failure in thread 140245598570832 in file handler/ha_innodb.cc line 2595 InnoDB: Failing assertion: error == DB_SUCCESS InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html InnoDB: about forcing recovery. 101210 16:35:51 - mysqld got signal 6 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=3 max_threads=600 threads_connected=3 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x18209220 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f8d791580d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f902a76a080] /lib/libc.so.6(gsignal+0x35) [0x7f90291f8fb5] /lib/libc.so.6(abort+0x183) [0x7f90291fabc3] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x41b) [0x781f4b] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f902a7623ba] /lib/libc.so.6(clone+0x6d) [0x7f90292abfcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x18213c70 = thd->thread_id=3 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 101210 16:35:51 mysqld_safe Number of processes running now: 0 101210 16:35:51 mysqld_safe mysqld restarted InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 101210 16:35:54 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 101210 16:35:56 InnoDB: Started; log sequence number 456 143528628 101210 16:35:56 [Warning] 'user' entry 'root@PSDB102' ignored in --skip-name-resolve mode. 101210 16:35:56 [Warning] Neither --relay-log nor --relay-log-index were used; so replication may break when this MySQL server acts as a slave and has his hostname changed!! Please use '--relay-log=mysqld-relay-bin' to avoid this problem. 101210 16:35:56 [Note] Event Scheduler: Loaded 0 events 101210 16:35:56 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.31-1ubuntu2-log' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 101210 16:36:11 InnoDB: Error: (1500) Couldn't read the MAX(job_id) autoinc value from the index (PRIMARY). 101210 16:36:11 InnoDB: Assertion failure in thread 139955151501648 in file handler/ha_innodb.cc line 2595 InnoDB: Failing assertion: error == DB_SUCCESS InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html InnoDB: about forcing recovery. 101210 16:36:11 - mysqld got signal 6 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=600 threads_connected=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x18588720 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f49d916f0d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f4c8a73f080] /lib/libc.so.6(gsignal+0x35) [0x7f4c891cdfb5] /lib/libc.so.6(abort+0x183) [0x7f4c891cfbc3] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x41b) [0x781f4b] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f4c8a7373ba] /lib/libc.so.6(clone+0x6d) [0x7f4c89280fcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x18599950 = thd->thread_id=1 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 101210 16:36:11 mysqld_safe Number of processes running now: 0 101210 16:36:11 mysqld_safe mysqld restarted The config is [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] innodb_file_per_table innodb_buffer_pool_size=10G innodb_log_buffer_size=4M innodb_flush_log_at_trx_commit=2 innodb_thread_concurrency=8 skip-slave-start server-id=3 # # * IMPORTANT # If you make changes to these settings and your system uses apparmor, you may # also need to also adjust /etc/apparmor.d/usr.sbin.mysqld. # user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /DB2/mysql tmpdir = /tmp skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. #bind-address = 127.0.0.1 # # * Fine Tuning # key_buffer = 16M max_allowed_packet = 16M thread_stack = 128K thread_cache_size = 8 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP max_connections = 600 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 1M query_cache_size = 32M # skip-federated slow-query-log skip-name-resolve Update: I followed the instructions as per http://dev.mysql.com/doc/refman/5.1/en/forcing-innodb-recovery.html and set innodb_force_recovery = 4 and the logs are showing a different error but the behavior is still the same: 101210 19:14:15 mysqld_safe mysqld restarted 101210 19:14:19 InnoDB: Started; log sequence number 456 143528628 InnoDB: !!! innodb_force_recovery is set to 4 !!! 101210 19:14:19 [Warning] 'user' entry 'root@PSDB102' ignored in --skip-name-resolve mode. 101210 19:14:19 [Warning] Neither --relay-log nor --relay-log-index were used; so replication may break when this MySQL server acts as a slave and has his hostname changed!! Please use '--relay-log=mysqld-relay-bin' to avoid this problem. 101210 19:14:19 [Note] Event Scheduler: Loaded 0 events 101210 19:14:19 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.31-1ubuntu2-log' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 101210 19:14:32 InnoDB: error: space object of table mydb/__twitter_friend, InnoDB: space id 1602 did not exist in memory. Retrying an open. 101210 19:14:32 InnoDB: error: space object of table mydb/access_request, InnoDB: space id 1318 did not exist in memory. Retrying an open. 101210 19:14:32 InnoDB: error: space object of table mydb/activity, InnoDB: space id 1595 did not exist in memory. Retrying an open. 101210 19:14:32 - mysqld got signal 11 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=600 threads_connected=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x1753c070 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f7a0b5800d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f7cbc350080] /usr/sbin/mysqld(ha_innobase::innobase_get_index(unsigned int)+0x46) [0x77c516] /usr/sbin/mysqld(ha_innobase::innobase_initialize_autoinc()+0x40) [0x77c640] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x3f3) [0x781f23] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f7cbc3483ba] /lib/libc.so.6(clone+0x6d) [0x7f7cbae91fcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x1754d690 = thd->thread_id=1 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash.

  Read the article

• Terminal Server 2008 Login: Access Denied

  - by user1236435

  When I try to RDP into a Server 2008 Terminal Server, I get a message that says "Access Denied" and an OK button. I setup the licensing mode correctly (per user) and also have setup to allow all remote connections. I get the following in the security event log: Log Name: Security Source: Microsoft-Windows-Security-Auditing Date: 28/06/2012 12:01:16 Event ID: 4656 Task Category: File System Level: Information Keywords: Audit Failure User: N/A Computer: 0BraApps1.brenntagLA.hou Description: A handle to an object was requested. Subject: Security ID: BRENNTAGLA\jaadmin Account Name: jaadmin Account Domain: BRENNTAGLA Logon ID: 0xbbe3f Object: Object Server: Security Object Type: File Object Name: C:\Windows\System32\ServerManager.msc Handle ID: 0x0 Process Information: Process ID: 0x60c Process Name: C:\Windows\System32\mmc.exe Access Request Information: Transaction ID: {00000000-0000-0000-0000-000000000000} Accesses: READ_CONTROL SYNCHRONIZE WriteData (or AddFile) AppendData (or AddSubdirectory or CreatePipeInstance) WriteEA ReadAttributes WriteAttributes Access Reasons: READ_CONTROL: Granted by D:(A;;0x1200a9;;;BA) SYNCHRONIZE: Granted by D:(A;;0x1200a9;;;BA) WriteData (or AddFile): Not granted AppendData (or AddSubdirectory or CreatePipeInstance): Not granted WriteEA: Not granted ReadAttributes: Granted by ACE on parent folder D:(A;;0x1301bf;;;BA) WriteAttributes: Not granted Access Mask: 0x120196 Privileges Used for Access Check: - Restricted SID Count: 0 Event Xml: 4656 1 0 12800 0 0x8010000000000000 1535565 Security 0BraApps1.brenntagLA.hou S-1-5-21-205301047-3902605089-2438454170-21511219 jaadmin BRENNTAGLA 0xbbe3f Security File C:\Windows\System32\ServerManager.msc 0x0 {00000000-0000-0000-0000-000000000000} %%1538 %%1541 %%4417 %%4418 %%4420 %%4423 %%4424 %%1538: %%1801 D:(A;;0x1200a9;;;BA) %%1541: %%1801 D:(A;;0x1200a9;;;BA) %%4417: %%1805 %%4418: %%1805 %%4420: %%1805 %%4423: %%1811 D:(A;;0x1301bf;;;BA) %%4424: %%1805 0x120196 - 0 0x60c C:\Windows\System32\mmc.exe Any ideas?

  Read the article

• Are there any Graphical PowerShell tools?

  - by Dai

  As a developer for the .NET platform, I like to "explore" a platform, framework or API by browsing through the API documentation which explains what everything is - everything is covered and when I use tools like Reflector or Object Browser then I get to know for certain what I'm working with. When I'm writing my own software I can use tools like the Object Test Bench to explore and work with my classes directly. I'm looking for something similar, but for PowerShell - and ones that avoid text-mode. PowerShell is nice, and there are a lot of cool "discoverability"-things it has, such as the "Verb-Noun" syntax, however when I'm working with Exchange Server, for example, I wanted to get a list of AD Permissions on a Receive Connector and I got this list: [PS] C:\Windows\system32>Get-ADPermission "Client SVR6" -User "NT AUTHORITY\Authenticated Users" | fl User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : False AccessRights : {ExtendedRight} IsInherited : False Properties : ChildObjectTypes : InheritedObjectType : InheritanceType : All User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : False AccessRights : {ExtendedRight} IsInherited : False Properties : ChildObjectTypes : InheritedObjectType : InheritanceType : All User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : False AccessRights : {ExtendedRight} IsInherited : False Properties : ChildObjectTypes : InheritedObjectType : InheritanceType : All User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : False AccessRights : {ExtendedRight} IsInherited : False Properties : ChildObjectTypes : InheritedObjectType : InheritanceType : All User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : False AccessRights : {ExtendedRight} IsInherited : False Properties : ChildObjectTypes : InheritedObjectType : InheritanceType : All User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : True AccessRights : {ReadProperty} IsInherited : True Properties : {ms-Exch-Availability-User-Password} ChildObjectTypes : InheritedObjectType : ms-Exch-Availability-Address-Space InheritanceType : Descendents [PS] C:\Windows\system32> Note how the first few entries contain identical text - there's no way to tell them apart easily. But if there was a GUI presumably it would let me drill-down into the differences better. Are there any tools that do this?

  Read the article

• Troubleshooting wireless client-bridged networks between two DD-WRT routers?

  - by KronoS

  I recently purchased a Buffalo N600 wireless router which came with DD-WRT pre-installed. I want to take my old wireless router a Linksys WRT54GL, also with DD-WRT pre-installed, and use it as a wireless bridge for my HTPC and Blu-Ray Player in the other room. I other words, I'm trying to connect to WIRED networks via the wireless on the routers. I followed eactly the instruction from DD-WRT's manual for 'Client Bridged' however I'm still not able to connect to two routers correctly, when the encryption is enabled (WPA2-Personal Mixed) however I am able to connect the two routers when there is NO encryption. I've checked, double checked, and triple checked that EVERYTHING is the same on BOTH routers: Routers 1 & 2 Encryption: WPA2-Personal Mixed Wireless Mode: G-Only Wireless Channel: 6 Subnet Mask: 255.255.255.0 Subnet: 192.168.1.0/254 SSID: Krono$ Primary Router #1 (Buffalo N600) IP Address: 192.168.1.1 Firewall: Enables w/ defaults DCHP: Enabled as DHCP Server Secondary Router #2 (Linksys WRT54GL) IP Address: 192.168.1.2 Firewall: Disabled as per DD-WRT instructions I'm looking for any configurations that I may have missed, or settings that may need to happen in order for this work.

  Read the article

< Previous Page | 480 481 482 483 484 485 486 487 488 489 490 491  | Next Page >