Search Results

Search found 16218 results on 649 pages for 'compiler errors'.

Page 485/649 | < Previous Page | 481 482 483 484 485 486 487 488 489 490 491 492  | Next Page >

• Experience with AMCC 3ware 9650se raid cards? Ours seems dead

  - by antiduh

  We have a 8-port 3ware 9650se raid card for our main disk array. We had to bring the server down for a pending power outage, and when we turned the machine back on, the raid card never started. This card has been in service for a couple years without problems, and was working up until the shutdown. Now, when we turn the machine on, the bios option rom that normally kicks in before the bootloader doesn't show up, none of the drives start, and when the OS tries to access the device, it just times out. The firmware on it has been upgraded in the past, so it's possible we've hit some sort of firmware bug. We're using it in a Silicon Mechanics R272 machine with gentoo for the OS. The OS eventually boots, but alas, without the card. We've ordered a new one, but I'm worried that if we replace the card it won't recognize the existing array. Has anybody performed a card swap before? Any help would be greatly appreciated. Edit: These are the kernel errors we see: 3ware 9000 Storage Controller device driver for Linux v2.26.02.012. 3w-9xxx 0000:09:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 3w-9xxx 0000:09:00.0: setting latency timer to 64 3w-9xxx: scsi0: ERROR: (0x06:0x000D): PCI Abort: clearing. 3w-9xxx: scsi0: ERROR: (0x06:0x001F): Microcontroller not ready during reset sequence. 3w-9xxx: scsi0: ERROR: (0x06:0x0036): Response queue (large) empty failed during reset sequence. 3w-9xxx 0000:09:00.0: PCI INT A disabled

  Read the article

• email output of powershell script

  - by Gordon Carlisle

  I found this wonderful script that outputs the status of the current DFS backlog to the powershell console. This works great, but I need the script to email me so I can schedule it to run nightly. I have tried using the Send-MailMessage command, but can't get it to work. Mainly because my powershell skills are very weak. I believe most of the issue revolve around the script using the Write-Host command. While the coloring is nice I would much rather have it email me the results. I also need the solution to be able to specify a mail server since the dfs servers don't have email capability. Any help or tips are welcome and appreciated. Here is the code. $RGroups = Get-WmiObject -Namespace "root\MicrosoftDFS" -Query "SELECT * FROM DfsrReplicationGroupConfig" $ComputerName=$env:ComputerName $Succ=0 $Warn=0 $Err=0 foreach ($Group in $RGroups) { $RGFoldersWMIQ = "SELECT * FROM DfsrReplicatedFolderConfig WHERE ReplicationGroupGUID='" + $Group.ReplicationGroupGUID + "'" $RGFolders = Get-WmiObject -Namespace "root\MicrosoftDFS" -Query $RGFoldersWMIQ $RGConnectionsWMIQ = "SELECT * FROM DfsrConnectionConfig WHERE ReplicationGroupGUID='"+ $Group.ReplicationGroupGUID + "'" $RGConnections = Get-WmiObject -Namespace "root\MicrosoftDFS" -Query $RGConnectionsWMIQ foreach ($Connection in $RGConnections) { $ConnectionName = $Connection.PartnerName.Trim() if ($Connection.Enabled -eq $True) { if (((New-Object System.Net.NetworkInformation.ping).send("$ConnectionName")).Status -eq "Success") { foreach ($Folder in $RGFolders) { $RGName = $Group.ReplicationGroupName $RFName = $Folder.ReplicatedFolderName if ($Connection.Inbound -eq $True) { $SendingMember = $ConnectionName $ReceivingMember = $ComputerName $Direction="inbound" } else { $SendingMember = $ComputerName $ReceivingMember = $ConnectionName $Direction="outbound" } $BLCommand = "dfsrdiag Backlog /RGName:'" + $RGName + "' /RFName:'" + $RFName + "' /SendingMember:" + $SendingMember + " /ReceivingMember:" + $ReceivingMember $Backlog = Invoke-Expression -Command $BLCommand $BackLogFilecount = 0 foreach ($item in $Backlog) { if ($item -ilike "*Backlog File count*") { $BacklogFileCount = [int]$Item.Split(":")[1].Trim() } } if ($BacklogFileCount -eq 0) { $Color="white" $Succ=$Succ+1 } elseif ($BacklogFilecount -lt 10) { $Color="yellow" $Warn=$Warn+1 } else { $Color="red" $Err=$Err+1 } Write-Host "$BacklogFileCount files in backlog $SendingMember->$ReceivingMember for $RGName" -fore $Color } # Closing iterate through all folders } # Closing If replies to ping } # Closing If Connection enabled } # Closing iteration through all connections } # Closing iteration through all groups Write-Host "$Succ successful, $Warn warnings and $Err errors from $($Succ+$Warn+$Err) replications." Thanks, Gordon

  Read the article

• r1soft agent is failing with the error: "write error while sending code: Broken pipe"

  - by curiousguy

  I have an Ubuntu 10.04.4 LTS server with r1soft agent installed in it. Recently, the backups are failing with the following error. -------- write error while sending code: Broken pipe -------- I have reinstalled the buagent but to no avail. On checking the server logs, I could see the following errors listed in it: -------- # tail -f /var/log/messages |grep -i buagent Nov 17 03:35:06 microscope buagent: Need to back up 126 sectors Nov 17 03:35:06 microscope buagent: (Righteous Backup Linux Agent) 1.79.0 build 12433 Nov 17 03:35:06 microscope buagent: allowing control from backup server (10.128.136.195) with valid RSA key Nov 17 03:35:06 microscope buagent: allowing control from backup server (10.128.136.201) with valid RSA key Nov 17 03:35:06 microscope buagent: sending auth challenge for allowed host at (10.128.136.201) port (47890) Nov 17 03:35:06 microscope buagent: host (10.128.136.201) port (47890) authentication successful Nov 17 03:35:06 microscope buagent: Backup request accepted. Starting backup. Nov 17 03:35:06 microscope buagent: Snapshot completed in 0.010 seconds. Nov 17 03:45:03 microscope buagent: Error reading blocks from snapshot. Nov 17 03:45:03 microscope buagent: Reading blocks failed Nov 17 03:45:03 microscope buagent: error backup aborted Nov 17 03:45:03 microscope buagent: backup failed on agent closing connection Nov 17 03:45:03 microscope buagent: Backup failed. Nov 17 03:45:03 microscope buagent: write error while sending code: Broken pipe (32) Nov 17 03:45:03 microscope buagent: tell child write failed -------- I tried changing the 'Timeout' and 'DiskAsPartition' value in '/etc/buagent/agent_config' file but no luck. Also, verified that proper route is added to the backup server. The agent is also running fine. Am I missing anything? Any help would be much appreciated. Note: CDP 2.0 is installed in the backup server.

  Read the article

• Wrong CSS mime type with Roundcube 0.5 beta and nginx

  - by Julien Vehent

  I'm running into a CSS problem. This is a setup based on Debian Squeeze (nginx/0.7.67, php5/cgi) on which I installed the latest Roundcube 0.5 beta. PHP is properly processed, login works fine but the CSS files are not loaded and Firefox is throwing the following errors: Error: The stylesheet https://webmail.example.net:10443/roundcube/skins/default/common.css?s=1290600165 was not loaded because its MIME type, "text/html", is not "text/css". Source File: https://webmail.example.net:10443/roundcube/?_task=login Line: 0 Error: The stylesheet https://webmail.example.net:10443/roundcube/skins/default/mail.css?s=1290156319 was not loaded because its MIME type, "text/html", is not "text/css". Source File: https://webmail.example.net:10443/roundcube/?_task=login Line: 0 As far as I understand, nginx doesn't see the .css extension (because ofthe ?s= argument) and thus set the mime type with the default value, being text/html. Should I fix this in nginx (and how ?) or is it roundcube's related ? Edit: It seems that it's nginx related. The content-type isn't set for any other type than text/html. I had to include manually the following declarations to force CSS and JS content-types. That's ugly, and I never had the problem before... any idea ? location ~ \.css { add_header Content-Type text/css; } location ~ \.js { add_header Content-Type application/x-javascript; }

  Read the article

• WebDAV through Apache2 permissions/missing files

  - by Strifariz

  I have a WebDAV setup on Apache2 on a server running Debian 5.0 (Lenny), which I am accessing through a mapped network drive under Windows 7. The setup appears to run fine, I receive no permission errors when copying a file to the share the first time, but the file never shows up in the directory (it's invisible, doing a ls -lha on the directory as root on the server also shows no files. When attempting to copy the file once more I am informed that the file already exists though, and I am asked if I wish to overwrite the file, when selecting "Yes" to this, I receive a permission error saying I'm not able to write to the folder. My logs aren't reporting any access violations of any kind, what could be the problem? (See log excerpt below) [17/Jan/2011:10:26:34 +0100] "PUT /1.png HTTP/1.1" 401 525 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:34 +0100] "PUT /1.png HTTP/1.1" 201 304 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:34 +0100] "LOCK /1.png HTTP/1.1" 401 525 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:34 +0100] "LOCK /1.png HTTP/1.1" 200 447 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:34 +0100] "PROPPATCH /1.png HTTP/1.1" 401 525 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:34 +0100] "PROPPATCH /1.png HTTP/1.1" 207 389 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:34 +0100] "HEAD /1.png HTTP/1.1" 401 - "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:34 +0100] "HEAD /1.png HTTP/1.1" 200 - "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:34 +0100] "PUT /1.png HTTP/1.1" 401 525 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:35 +0100] "PUT /1.png HTTP/1.1" 204 - "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:35 +0100] "PROPPATCH /1.png HTTP/1.1" 401 525 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:35 +0100] "PROPPATCH /1.png HTTP/1.1" 207 389 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:35 +0100] "UNLOCK /1.png HTTP/1.1" 401 525 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:35 +0100] "UNLOCK /1.png HTTP/1.1" 204 - "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:38 +0100] "PROPFIND / HTTP/1.1" 401 525 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:38 +0100] "PROPFIND / HTTP/1.1" 207 1634 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600"

  Read the article

• Network corruption - corrupt downloads, corrupt streams, etc.

  - by rfrankel

  I've been having some problems with my home LAN. Downloaded executables won't run, my remote desktop sessions keep getting interrupted due to encryption errors, flash video streams show visible corruption (both Hulu and YouTube), and I've had a couple downloads for which the md5 hashes don't match. The problem has even occurred with a couple images embedded in webpages, though that's rare enough (presumably because images are relatively smaller files). I've had this problem across two Windows machines and a Mac, so it's neither machine-specific nor at the app or OS level. Comcast claims it's nothing to do with them, and my Linksys/Cisco RV016 router is out of warranty, so I have no access to official support. When I log into my router, it shows no error packets or dropped packets received. I plugged a laptop directly into the router and was able to download a 5.5 MB file and verify its MD5 hash, which is not proof that the problem is downstream of the router, but makes it seem quite likely, since I failed to download the same file several times from two desktops (one Mac, one Windows). Could this be a wiring problem? If so, is there any way clever/elegant to determine which wiring is faulty with just software? If I can avoid tracing all the wires throughout my entire house it would make my life quite a bit easier.

  Read the article

• Loading the 'pktgen' module on Ubuntu Server

  - by StackedCrooked

  I would like to enable and use the pktgen module on Ubuntu Server. I have enabed the module by adding a line containing 'pktgen' to the /etc/modules file. After rebooting it seems that the module is successfully loaded because the directory /proc/net/pktgen exists. However when trying to run the first sample I get these errors: root@ubuntu:~# bash ./pktgen.conf-1-1 Removing all devices Adding eth4 Setting max_before_softirq 10000 Configuring /proc/net/pktgen/eth4 ./pktgen.conf-1-1: line 9: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory ./pktgen.conf-1-1: line 9: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory ./pktgen.conf-1-1: line 9: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory ./pktgen.conf-1-1: line 9: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory ./pktgen.conf-1-1: line 9: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory ./pktgen.conf-1-1: line 9: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory Running... ctrl^C to stop Done It turns out the script simply unable to write a file to the /proc/net/pktgen directory. When I try this manually it fails as well: root@ubuntu:~# cd /proc/net/pktgen/ root@ubuntu:/proc/net/pktgen# touch eth4 touch: cannot touch `eth4': No such file or directory Can anyone help me make it work? I'm using Ubuntu version: 2.6.32-21-server. Fixed I apologize for keeping this post not up to date. I was able to fix it. If I remember well the cause of the error was that eth4 did not exist, or did not have the 'online' status. Anyway, it is fixed now.

  Read the article

• SQL Server 2008 cluster freezing

  - by Ed Leighton-Dick

  We have run into a strange situation in which a SQL Server 2008 single-node cluster hangs. As background, we are rebuilding a Windows Server 2003/SQL Server 2005 two-node cluster using Windows 2008 and SQL Server 2008. Here's the timeline: Evicted the passive node (server B) from the Windows 2003/SQL 2005 cluster. The active node now functions as a single-node cluster with no problems. Wiped server B's disks and installed Windows 2008 and SQL Server 2008 as a single-node cluster. Since we do not want to the two clusters to communicate yet, we left the cluster's private network "heartbeat" adapter unconfigured. The cluster comes up and functions normally. Moved all databases to the new cluster. Cluster continues to function normally. Turned off server A (old cluster) in preparation for rebuilding as the second node of the new cluster. SQL Server instance on server B (new cluster) locks up, even though it should have no knowledge of or interaction with server A. Restarted server A. SQL Server instance on server B (new cluster) immediately begins working again. Things we have tried: The new cluster's name responds to ping and NETBIOS requests, even while the SQL Server is hung. We have confirmed that no IP address is assigned to the old heartbeat adapter, and it is not pulling an IP address from DHCP. Disabling the heartbeat's network card has the same effect. No errors were generated in any logs - Windows or SQL. When the error first occurred, it sat in the hung state for quite some time (well over 10 minutes) before anyone figured out what was going on. This would seem to eliminate any sort of normal cluster timeout in which it would have been searching for the other node (even if one had been configured). Server B is running Windows 2008 SP2, fully patched, and SQL Server 2008 SP1 CU7 (10.0.2775).

  Read the article

• problem booting crusty old windows XP

  - by Carson Myers

  I have an acer aspire laptop running Windows XP home. I believe I have some virus on it, I'm not sure--I mostly just run linux in a VM on it so I wasn't too worried. I'm not sure if that virus caused this problem. The laptop wasn't recognizing my USB hard drive for some reason so I decided to restart it. When it started up, it got past the memory test, past the boot screen, (but it paused right here on a blank screen for awhile) and flashed the desktop once (like it does just before the login screen) and then crashed. I got a quick BSOD and then it restarted. Then it tried to boot again, etc etc infinite loop of failure. Well, before trying safe mode, I disabled automatic restart on system crash so I could read the blue screen. There wasn't anything important on it, it said *** STOP: 0x00000000 (0xC0000000 0x,.... ) beginning physical memory dump physical memory dump complete That's not verbatim (obviously) but it didn't help me. so I booted in safe mode, and it stopped on the driver gagp30kx.sys and then restarted (and infinite loop of failure again). I burned a recovery CD and tried that. It loaded it, and I went into repair mode. I ran chkdsk and then disabled the AGP driver. Same thing on booting in safe mode except it stopped at mup.sys instead. I enabled the AGP driver again, and ran chkdsk again from the CD. It said it found problems but didn't say it fixed them. So I ran it a second time, and it said "performing additional checking or recovery" lots of times (I can't tell how many, they went above the screen top). I tried booting again and no luck. Every time I run chkdsk after trying to boot again it says it found and fixed more errors. I think it might be whatever driver is after the AGP driver, but I don't know what it is or how to find out. Can anyone help me fix this?

  Read the article

• HP Storageworks 448 tape drive input/output error with Ubuntu

  - by Dan D

  I'm trying to set a backup to tape of a machine using flexbackup. However any attempt to write to the tape drive (via either flexbackup or just tar) results in "/dev/st0: Input/output error" The machine seems to recognise the drive (HP Storageworks Ultrium 448) and that there's a tape in it and "mt status" seems to work... "mt -f /dev/st0 rewind" or "erase" throw no errors... root@stor001:/# mt status SCSI 2 tape drive: File number=0, block number=0, partition=0. Tape block size 0 bytes. Density code 0x42 (LTO-2). Soft error count since last status=0 General status bits on (41010000): BOT ONLINE IM_REP_EN root@stor001:/# cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: DVDRAM GSA-4084N Rev: KS02 Type: CD-ROM ANSI SCSI revision: 05 Host: scsi2 Channel: 00 Id: 03 Lun: 00 Vendor: HP Model: Ultrium 2-SCSI Rev: S65D Type: Sequential-Access ANSI SCSI revision: 03 "tell" does however root@stor001:/# mt -f /dev/st0 tell /dev/st0: Input/output error Based on a forum post I found, I tried: root@stor001:/# dd if=/dev/zero of=/dev/nst0 bs=1024 count=10 10+0 records in 10+0 records out 10240 bytes (10 kB) copied, 5.0815 s, 2.0 kB/s which gave the person on the forum an error but seems to work for me. If anyone has any suggestions, I'm all ears...

  Read the article

• How should secret files be pushed to an EC2 (on AWS) Ruby on Rails application?

  - by nikc

  How should secret files be pushed to an EC2 Ruby on Rails application using amazon web services with their elastic beanstalk? I add the files to a git repository, and I push to github, but I want to keep my secret files out of the git repository. I'm deploying to aws using: git aws.push The following files are in the .gitignore: /config/database.yml /config/initializers/omniauth.rb /config/initializers/secret_token.rb Following this link I attempted to add an S3 file to my deployment: http://docs.amazonwebservices.com/elasticbeanstalk/latest/dg/customize-containers.html Quoting from that link: Example Snippet The following example downloads a zip file from an Amazon S3 bucket and unpacks it into /etc/myapp: sources: /etc/myapp: http://s3.amazonaws.com/mybucket/myobject Following those directions I uploaded a file to an S3 bucket and added the following to a private.config file in the .elasticbeanstalk .ebextensions directory: sources: /var/app/current/: https://s3.amazonaws.com/mybucket/config.tar.gz That config.tar.gz file will extract to: /config/database.yml /config/initializers/omniauth.rb /config/initializers/secret_token.rb However, when the application is deployed the config.tar.gz file on the S3 host is never copied or extracted. I still receive errors that the database.yml couldn't be located and the EC2 log has no record of the config file, here is the error message: Error message: No such file or directory - /var/app/current/config/database.yml Exception class: Errno::ENOENT Application root: /var/app/current

  Read the article

• BSOD trying to migrate Windows XP from a physical to a virtual machine

  - by pauldoo

  I am attempting to migrate a Windows XP Home installation from a physical machine to a virtual machine. The physical machine has two hard disks; the first is 250GB containing the "C:", the second is 1TB containing "D:". I'd like to create a new virtual machine stored on the D:, which is a copy of the Windows XP Home installation that is currently on the C:. (This will leave the 250GB drive clear for me to install a fresh copy of Windows 7, and still be able to access the old XP installation if necessary.) The first method I tried was to follow the instructions here: http://www.virtualbox.org/wiki/Migrate_Windows I booted up from an Ubuntu Live CD in order to execute the Linux commands whilst the Windows system wasn't running. With this method the virtual machine would always blue screen on startup with a "STOP 0x0000007B" message. The instructions above say to try a "repair install" using the Windows XP disc. Unfortunately for me my XP disc is scratched and will not boot so I was unable to try a repair install. The second method I tried was to use "VMWare Converter Standalone Client". This tool executed without any errors, but again produced a virtual machine that blue screens on startup with the same "STOP" message. Are there any other methods to move the Windows XP installation into a virtual machine? I think next I will try some more manual process to create the cloned virtual machine. I think I will try installing a fresh copy of Windows XP to a virtual machine, then once that is booting OK I will ntfsclone the source C: partition over the top. Perhaps this will fix the booting problems if the issue is related to the MBR or partition table in some way.

  Read the article

• How do I easily repair a single unreadable block on a Linux disk?

  - by Nelson

  My Linux system has started throwing SMART errors in the syslog. I tracked it down and believe the problem is a single block on the disk. How do I go about easily getting the disk to reallocate that one block? I'd like to know what file got destroyed in the process. (I'm aware that if one block fails on a disk others are likely to follow; I have a good ongoing backup and just want to try to keep this disk working.) Searching the web leads to the Bad block HOWTO, which describes a manual process on an unmounted disk. It seems complicated and error-prone. Is there a tool to automate this process in Linux? My only other option is the manufacturer's diagnostic tool, but I presume that'll clobber the bad block without any reporting on what got destroyed. Worst case, it might be filesystem metadata. The disk in question is the primary system partition. Using ext3fs and LVM. Here's the error log from syslog and the relevant bit from smartctl. smartd[5226]: Device: /dev/hda, 1 Currently unreadable (pending) sectors Error 1 occurred at disk power-on lifetime: 17449 hours (727 days + 1 hours) ... Error: UNC at LBA = 0x00d39eee = 13868782 There's a full smartctl dump on pastebin.

  Read the article

• NRPE unable to read output, but why?

  - by ticktockhouse

  I have this problem with NRPE, all the stuff I've found so far on the net seems to point me at things I've already tried. # /usr/local/nagios/plugins/check_nrpe -H nrpeclient gives NRPE v2.12 as expected. Running the command by hand (as defined in nrpe.cfg on "nrpeclient", gives the expected response nrpe.cfg: command[check_openmanage]=/usr/lib/nagios/plugins/additional/check_openmanage -s -e -b ctrl_driver=0 bat_charge "Expected response" But if I try to run the command from the Nagios server I get the following: # /usr/local/nagios/plugins/check_nrpe -H comxps -c check_openmanage NRPE: Unable to read output Can anyone think of anywhere else I might have made a mistake with this? I've done the same thing on multiple other servers with no problem. The only difference I can think of with this is that this box is RHEL 5 based, whereas the others are RHEL 4 based. Those two bits above that I've tested are the what most people seem to suggest when people have had this problem. I should mention that I get a weird error in the logs when I restart nrpe: nrpe[14534]: Unable to open config file '/usr/local/nagios/etc/nrpe.cfg' for reading nrpe[14534]: Continuing with errors... nrpe[14535]: Starting up daemon nrpe[14535]: Warning: Daemon is configured to accept command arguments from clients! nrpe[14535]: Listening for connections on port 5666 nrpe[14535]: Allowing connections from: bodbck,combck,nam-bck Even though, it's plainly reading that /usr/local/nagios/etc/nrpe.cfg file to get the stuff it's talking about further down..

  Read the article

• "A disk read error occurred" when booting XP disk image in VirtualBox

  - by intuited

  I'm trying to boot an XP installation cloned into VirtualBox from a real drive. I'm getting the message A disk read error occurred Press Ctrl+Alt+Del to restart whenever* I try to boot the machine. * This is not strictly true: with AMD-V enabled, the boot process appears to not make it this far and instead hangs at a black screen with cursor. I created the VirtualBox image from the original drive using the following method: $ sudo ddrescue -n /dev/sdd sdd.img logfile # completed without errors $ VBoxManage convertfromraw sdd.img disk.vdi The original disk (and the image) contain a single NTFS partition with XP installed on it. The owner of the drive indicates that it did boot okay the last time the system made it that far. The (Pentium 4) system has a broken (enormous) heat sink, so at some point it failed to boot because it would quickly overheat and shut down. If I boot the VM from a live cd, I am able to mount its /dev/sda1 without any problems. I ran ntfsfix and didn't have any luck. I've read through the instructions on doing this. I didn't really follow them. For example, I didn't run MergeIDE before imaging because the machine was not bootable. However, the symptom of that problem seems to be quite different. The emitted message is contained in the volume boot record of the XP partition, which leads me to suspect that this is a problem with the core operating system bootstrap procedure, and not related to anything in the registry. I don't have an XP boot CD.

  Read the article

• Linux error when resume from RAM

  - by TuxPotato

  The last two times that I have resumed my laptop from sleep, it has hung and given me this set of errors: [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 hda_intel: azx_get_responce timeout, switching to single_cmd mode: last cmd=0x01170700 ata6: softreset failed (device not ready) ata4: softreset failed (device not ready) [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 The last two messages repeat two more times. The first time this happened, Linux's Magic SysRq worked and did a soft reboot, and after that everything was fine till it went to sleep again. It wakes up and gives me this. Here are the laptop stats: Toshiba Satellite L455D-S5976 AMD Sempron SI-42 Processor 2GB DDR2 RAM HD TruBrite Display ATI Radeon Graphics (integrated) Running Ubuntu 10.10 32 bit I'm not sure about the hard drive, but its a 250GB drive with one NTFS partition, two Hidden NTFS, one Linux Swap, and one Ext4. Can someone tell me whats wrong with my laptop? NOTE: This only happens when I close the screen. My computer doesn't go to sleep with the screen open.

  Read the article

• Postfix installation error on Ubuntu

  - by kgpdeveloper

  How do I fix this error on Ubuntu 10.04 ? Reading package lists... Done Building dependency tree Reading state information... Done postfix is already the newest version. The following packages were automatically installed and are no longer required: libaprutil1-dbd-sqlite3 libcap2 apache2.2-bin libapr1 libaprutil1-ldap libaprutil1 php5-common Use 'apt-get autoremove' to remove them. 0 upgraded, 0 newly installed, 0 to remove and 1 not upgraded. 1 not fully installed or removed. After this operation, 0B of additional disk space will be used. Setting up postfix (2.7.0-1) ... Postfix configuration was not changed. If you need to make changes, edit /etc/postfix/main.cf (and others) as needed. To view Postfix configuration values, see postconf(1). After modifying main.cf, be sure to run '/etc/init.d/postfix reload'. Running newaliases newaliases: warning: valid_hostname: numeric hostname: 202002 newaliases: fatal: file /etc/postfix/main.cf: parameter myhostname: bad parameter value: 202002 dpkg: error processing postfix (--configure): subprocess installed post-installation script returned error exit status 75 Processing triggers for libc-bin ... ldconfig deferred processing now taking place Errors were encountered while processing: postfix E: Sub-process /usr/bin/dpkg returned an error code (1) Even if I reboot, the same error shows up. Thanks for the help..

  Read the article

• Apache2 will not start on OpenSUSE after enabling mod_pagespeed

  - by alpha1

  I have a linode VPS, running openSUSE 12.1 (A little outdated, but stable). I have installed the RPMS for mod_pagespeed. mod_pagespeed.conf has "ModPagespeed on". Restarting apache fails after enabling pagespeed. the errors are not very helpful. li361-39:/usr/lib64/apache2 # a2enmod pagespeed li361-39:/usr/lib64/apache2 # service apache2 restart redirecting to systemctl Job failed. See system logs and 'systemctl status' for details. li361-39:/usr/lib64/apache2 # systemctl status apache2.service apache2.service - apache Loaded: loaded (/lib/systemd/system/apache2.service; enabled) Active: failed since Thu, 06 Jun 2013 20:49:00 +0000; 1s ago Process: 6701 ExecStop=/usr/sbin/httpd2 -D SYSTEMD -k stop (code=exited, status=0/SUCCESS) Process: 6704 ExecStart=/usr/sbin/start_apache2 -D SYSTEMD -k start (code=exited, status=1/FAILURE) Main PID: 6637 (code=exited, status=0/SUCCESS) CGroup: name=systemd:/system/apache2.service li361-39:/usr/lib64/apache2 # a2dismod pagespeed li361-39:/usr/lib64/apache2 # service apache2 restart redirecting to systemctl li361-39:/usr/lib64/apache2 # And the error log (/var/log/apache2/error_log) is useless as well. [Thu Jun 06 20:48:59 2013] [notice] caught SIGTERM, shutting down [Thu Jun 06 20:49:12 2013] [warn] Init: Session Cache is not configured [hint: SSLSessionCache] [Thu Jun 06 20:49:13 2013] [notice] Apache/2.2.21 (Linux/SUSE) mod_ssl/2.2.21 OpenSSL/1.0.0k PHP/5.4.15 configured -- resuming normal operations EDIT This is from /var/log/messages Jun 12 14:24:14 li361-39 start_apache2[27951]: httpd2-prefork: Syntax error on line 116 of /etc/apache2/httpd.conf: Syntax error on line 34 of /etc/apache2/sysconfig.d/loadmodule.conf: Cannot load /usr/lib64/apache2/mod_pagespeed.so into server: /usr/lib64/apache2/mod_pagespeed.so: undefined symbol: ap_unixd_config Full Log is here: http://pastebin.com/hjnbZZTr I've tried looking for other logs and checking the mod_pagespeed.conf against posts claiming it works and nothing is striking as wrong. Any Ideas?

  Read the article

• NFS4 permission denied when userid does not match (even though idmap is working)

  - by SystemParadox

  I have NFS4 setup with idmapd working correctly. ls -l from the client shows the correct user names, even though the user ids differ between the machines. However, when the user ids do not match, I get 'permission denied' errors trying access files, even though ls -l shows the correct username. When the user ids do happen to match by coincidence, everything works fine. sudo sysctl -w sunrpc.nfsd_debug=1023 gives the following output in the server syslog for the failed file access: nfsd_dispatch: vers 4 proc 1 nfsv4 compound op #1/3: 22 (OP_PUTFH) nfsd: fh_verify(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsv4 compound op ffff88003d0f5078 opcnt 3 #1: 22: status 0 nfsv4 compound op #2/3: 3 (OP_ACCESS) nfsd: fh_verify(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsd: fh_verify - just checking nfsv4 compound op ffff88003d0f5078 opcnt 3 #2: 3: status 0 nfsv4 compound op #3/3: 9 (OP_GETATTR) nfsd: fh_verify(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsd: fh_verify - just checking nfsv4 compound op ffff88003d0f5078 opcnt 3 #3: 9: status 0 nfsv4 compound returned 0 nfsd_dispatch: vers 4 proc 1 nfsv4 compound op #1/7: 22 (OP_PUTFH) nfsd: fh_verify(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsv4 compound op ffff88003d0f5078 opcnt 7 #1: 22: status 0 nfsv4 compound op #2/7: 32 (OP_SAVEFH) nfsv4 compound op ffff88003d0f5078 opcnt 7 #2: 32: status 0 nfsv4 compound op #3/7: 18 (OP_OPEN) NFSD: nfsd4_open filename dom_file op_stateowner (null) renewing client (clientid 4f96587d/0000000e) nfsd: nfsd_lookup(fh 28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba, dom_file) nfsd: fh_verify(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsd: fh_verify - just checking nfsd: fh_lock(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) locked = 0 nfsd: fh_compose(exp 08:01/22806529 srv/dom_file, ino=22809724) nfsd: fh_verify(36: 01070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsd: fh_verify - just checking fh_verify: srv/dom_file permission failure, acc=804, error=13 nfsv4 compound op ffff88003d0f5078 opcnt 7 #3: 18: status 13 nfsv4 compound returned 13 Is that useful to anyone? Any hints on to debug this would be greatly appreciated. Server kernel: 2.6.32-40-server (Ubuntu 10.04) Client kernel: 3.2.0-27-generic (Ubuntu 12.04) Same problem with my new server running 3.2.0-27-generic (Ubuntu 12.04). Thanks.

  Read the article

• yum error when installing memcached

  - by Jack

  Hi, trying to install memcached with "yum install memcached" and i'm getting all these errors which I have no idea how to solve. Setting up Install Process Resolving Dependencies -- Running transaction check --- Package memcached.x86_64 0:1.4.5-1.el5.rf set to be updated -- Processing Dependency: perl(AnyEvent) for package: memcached -- Processing Dependency: perl(AnyEvent::Socket) for package: memcached -- Processing Dependency: perl(AnyEvent::Handle) for package: memcached -- Processing Dependency: perl(YAML) for package: memcached -- Processing Dependency: perl(Term::ReadKey) for package: memcached -- Processing Dependency: libevent-1.1a.so.1()(64bit) for package: memcached -- Running transaction check --- Package compat-libevent-11a.x86_64 0:3.2.1-1.el5.rf set to be updated --- Package memcached.x86_64 0:1.4.5-1.el5.rf set to be updated -- Processing Dependency: perl(AnyEvent) for package: memcached -- Processing Dependency: perl(AnyEvent::Socket) for package: memcached -- Processing Dependency: perl(AnyEvent::Handle) for package: memcached -- Processing Dependency: perl(YAML) for package: memcached -- Processing Dependency: perl(Term::ReadKey) for package: memcached -- Finished Dependency Resolution memcached-1.4.5-1.el5.rf.x86_64 from rpmforge has depsolving problems -- Missing Dependency: perl(AnyEvent::Socket) is needed by package memcached-1.4.5-1.el5.rf.x86_64 (rpmforge) memcached-1.4.5-1.el5.rf.x86_64 from rpmforge has depsolving problems -- Missing Dependency: perl(AnyEvent) is needed by package memcached-1.4.5-1.el5.rf.x86_64 (rpmforge) memcached-1.4.5-1.el5.rf.x86_64 from rpmforge has depsolving problems -- Missing Dependency: perl(AnyEvent::Handle) is needed by package memcached-1.4.5-1.el5.rf.x86_64 (rpmforge) memcached-1.4.5-1.el5.rf.x86_64 from rpmforge has depsolving problems -- Missing Dependency: perl(YAML) is needed by package memcached-1.4.5-1.el5.rf.x86_64 (rpmforge) memcached-1.4.5-1.el5.rf.x86_64 from rpmforge has depsolving problems -- Missing Dependency: perl(Term::ReadKey) is needed by package memcached-1.4.5-1.el5.rf.x86_64 (rpmforge) Packages skipped because of dependency problems: compat-libevent-11a-3.2.1-1.el5.rf.x86_64 from rpmforge memcached-1.4.5-1.el5.rf.x86_64 from rpmforge The perl modules that its complaining about are already installed. Any ideas?

  Read the article

• Apache Derby running in Tomcat shutdown issues

  - by Luke

  I have set up Derby Network Server to be hosted within a Tomcat environment. This works great. However, when I shut down Tomcat I get the following errors: 04/01/2011 10:41:41 AM org.apache.catalina.core.StandardService stop INFO: Stopping service Catalina 04/01/2011 10:41:41 AM org.apache.catalina.loader.WebappClassLoader clearReferencesJdbc SEVERE: The web application [/derby] registered the JBDC driver [org.apache.derby.jdbc.ClientDriver] but failed to unregister it when the web application was stopped. To prevent a memory leak, the JDBC Driver has been forcibly unregistered. 04/01/2011 10:41:41 AM org.apache.catalina.loader.WebappClassLoader clearReferencesJdbc SEVERE: The web application [/derby] registered the JBDC driver [org.apache.derby.jdbc.AutoloadedDriver] but failed to unregister it when the web application was stopped. To prevent a memory leak, the JDBC Driver has been forcibly unregistered. 04/01/2011 10:41:41 AM org.apache.catalina.loader.WebappClassLoader clearReferencesThreads SEVERE: The web application [/derby] appears to have started a thread named [derby.NetworkServerStarter] but has failed to stop it. This is very likely to create a memory leak. 04/01/2011 10:41:41 AM org.apache.catalina.loader.WebappClassLoader clearReferencesThreads SEVERE: The web application [/derby] appears to have started a thread named [NetworkServerThread_4] but has failed to stop it. This is very likely to create a memory leak. 04/01/2011 10:41:41 AM org.apache.catalina.loader.WebappClassLoader clearReferencesThreads SEVERE: The web application [/derby] appears to have started a thread named [DRDAConnThread_5] but has failed to stop it. This is very likely to create a memory leak. 04/01/2011 10:41:41 AM org.apache.catalina.loader.WebappClassLoader clearReferencesThreads SEVERE: The web application [/derby] appears to have started a thread named [DRDAConnThread_13] but has failed to stop it. This is very likely to create a memory leak. 04/01/2011 10:41:41 AM org.apache.coyote.http11.Http11Protocol destroy INFO: Stopping Coyote HTTP/1.1 on http-8080 I'm currently starting and stopping Tomcat with the following commands: ./catalina run ./catalina stop Is there a better way to shutdown Tomcat with Derby or can this be solved by a configuration change?

  Read the article

• WIM2VHD failing with "Cannot derive Volume GUID from mount point."

  - by Jacob

  I'm trying to use WIM2VHD according to the instructions on Scott Hanselman's blog post to create a Sysprepped VHD image to boot from. I've installed the WAIK, and I have my Windows 7 sources mounted as a virtual drive. When I try to run WIM2VHD like this: cscript WIM2VHD.wsf /wim:F:\sources\install.wim /sku:Ultimate /vhd:E:\WindowsSeven.vhd /size:30721 I get the following log: Log for WIM2VHD 6.1.7600.0 on 11/2/2009 at 10:51:18.16 Copyright (C) Microsoft Corporation. All rights reserved. MACHINE INFO: Build=7600 Platform=x86fre OS=Windows 7 Ultimate ServicePack= Version=6.1 BuildLab=win7_rtm BuildDate=090713-1255 Language=en-ZA INFO: Looking for IMAGEX.EXE... INFO: Looking for BCDBOOT.EXE... INFO: Looking for BCDEDIT.EXE... INFO: Looking for REG.EXE... INFO: Looking for DISKPART.EXE... INFO: Session key is E01E1ED7-C197-4814-BDE4-43B73E14FCC4 INFO: Inspecting the WIM... INFO: Configuring and formatting the VHD... ******************************************************************************* Error: 0: Cannot derive Volume GUID from mount point. ******************************************************************************* INFO: Unmounting the VHD due to error... WARNING: In order to help resolve the issue, temporary files have not been deleted. They are in: C:\Users\Jacob\AppData\Local\Temp\WIM2VHD.WSF\E01E1ED7-C197-4814-BDE4-43B73E14FCC4 *emphasized text*Summary: Errors: 1, Warnings: 1, Successes: 0 INFO: Done. Any ideas?

  Read the article

• Apache 2.2, worker mpm, mod_fcgid and PHP: Can't apply process slot

  - by mopoke

  We're having an issue on an apache server where every 15 to 20 minutes it stops serving PHP requests entirely. On occasions it will return a 503 error, other times it will recover enough to serve the page but only after a delay of a minute or more. Static content is still served during that time. In the log file, there's errors reported along the lines of: [Wed Sep 28 10:45:39 2011] [warn] mod_fcgid: can't apply process slot for /xxx/ajaxfolder/ajax_features.php [Wed Sep 28 10:45:41 2011] [warn] mod_fcgid: can't apply process slot for /xxx/statics/poll/index.php [Wed Sep 28 10:45:45 2011] [warn] mod_fcgid: can't apply process slot for /xxx/index.php [Wed Sep 28 10:45:45 2011] [warn] mod_fcgid: can't apply process slot for /xxx/index.php There is RAM free and, indeed, it seems that more php processes get spawned. /server-status shows lots of threads in the "W" state as well as some FastCGI processes in "Exiting(communication error)" state. I rebuilt mod_fcgid from source as the packaged version was quite old. It's using current stable version (2.3.6) of mod_fcgid. FCGI config: FcgidBusyScanInterval 30 FcgidBusyTimeout 60 FcgidIdleScanInterval 30 FcgidIdleTimeout 45 FcgidIOTimeout 60 FcgidConnectTimeout 20 FcgidMaxProcesses 100 FcgidMaxRequestsPerProcess 500 FcgidOutputBufferSize 1048576 System info: Linux xxx.com 2.6.28-11-server #42-Ubuntu SMP Fri Apr 17 02:45:36 UTC 2009 x86_64 GNU/Linux DISTRIB_ID=Ubuntu DISTRIB_RELEASE=9.04 DISTRIB_CODENAME=jaunty DISTRIB_DESCRIPTION="Ubuntu 9.04" Apache info: Server version: Apache/2.2.11 (Ubuntu) Server built: Aug 16 2010 17:45:55 Server's Module Magic Number: 20051115:21 Server loaded: APR 1.2.12, APR-Util 1.2.12 Compiled using: APR 1.2.12, APR-Util 1.2.12 Architecture: 64-bit Server MPM: Worker threaded: yes (fixed thread count) forked: yes (variable process count) Server compiled with.... -D APACHE_MPM_DIR="server/mpm/worker" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D DYNAMIC_MODULE_LIMIT=128 -D HTTPD_ROOT="" -D SUEXEC_BIN="/usr/lib/apache2/suexec" -D DEFAULT_PIDLOG="/var/run/apache2.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="/etc/apache2/mime.types" -D SERVER_CONFIG_FILE="/etc/apache2/apache2.conf" Apache modules loaded: alias.load auth_basic.load authn_file.load authz_default.load authz_groupfile.load authz_host.load authz_user.load autoindex.load cgi.load deflate.load dir.load env.load expires.load fcgid.load headers.load include.load mime.load negotiation.load rewrite.load setenvif.load ssl.load status.load suexec.load PHP info: PHP 5.2.6-3ubuntu4.6 with Suhosin-Patch 0.9.6.2 (cli) (built: Sep 16 2010 19:51:25) Copyright (c) 1997-2008 The PHP Group Zend Engine v2.2.0, Copyright (c) 1998-2008 Zend Technologies

  Read the article

• How can MySQL be in GDAL's dependencies when it's already installed?

  - by Julien Fouilhé

  I'm trying to install GDAL on my CentOS 64 bits server to be able to make some GIS operations. I tried a simple: # yum install gdal First, the GDAL version is 1.4 (the last released one is 1.9) Then, I see in the dependencies list mysql. But I have mysql already installed, from another repository (remi), with a newer version than the one suggested by yum... Is it a problem of architecture (yum suggests i386)? I risked a yes, but still impossible to install it! Here's the error I have. Transaction Check Error: package mysql-5.5.28-1.el5.remi.x86_64 (which is newer than mysql-5.0.95-1.el5_7.1.i386) is already installed Then, I tried to install it from sources with last version available (1.9.2). I downloaded the GDAL tar.gz, extracted the files and installed it like following: # tar -xzf gdal-1.9.2.tar.gz # ./configure --with-static-proj4=/usr/local/lib --with-threads --with-libtiff=internal --with-geotiff=internal --with-jpeg=internal --with-gif=internal --with-png=internal --with-libz=internal # make # make install But during the make, I have some strange errors displaying, about RegisterOGRMySQL, that I can't understand: chmod a+x gdal-config /bin/sh /home/benjamin/gdal-1.9.2/libtool --mode=link g++ gdalinfo.lo /home/benjamin/gdal-1.9.2/libgdal.la -o gdalinfo libtool: link: g++ .libs/gdalinfo.o -o .libs/gdalinfo /home/benjamin/gdal-1.9.2/.libs/libgdal.so -L/usr/local/lib/lib -L/usr/kerberos/lib64 -lproj -lsqlite3 /usr/lib64/libexpat.so -lpthread -lrt -lcurl -ldl -lgssapi_krb5 -lkrb5 -lk5crypto -lcom_err -lidn -lssl -lcrypto -lz -Wl,-rpath -Wl,/usr/local/lib -Wl,-rpath -Wl,/usr/lib64 /home/benjamin/gdal-1.9.2/.libs/libgdal.so: undefined reference to `RegisterOGRMySQL' collect2: ld returned 1 exit status make[1]: *** [gdalinfo] Error 1 make[1]: Leaving directory `/home/benjamin/gdal-1.9.2/apps' make: *** [apps-target] Error 2 Has anyone a solution? Thanks a lot!

  Read the article

• Permission denied when running Rails app in VirtualBox Ubuntu guest with files on Windows host

  - by Ola Tuvesson

  I think I'm close to having my dev environment set up exactly the way I want, but one final snag remains. I'm running VirtualBox on a Windows 7 64bit host, with my dev enviroment inside a Ubuntu 12.04 guest. I want to keep the files for my projects on the host filesystem - partly so I can access them when the Ubuntu guest is not running, but also so I can use Tortoise and other Windows based tools (cough Photoshop), and it also eases my backup scheme somewhat. So I've got a folder "Rails" on my NTFS drive, which I've shared (Samba) from the host with a user specifically created for the Ubuntu guest. The mount point has been set up and an entry added to fstab (cifs), using a credentials file and the options iocharset=utf8,mode=0777,dir_mode=07??77 This mounts fine and my Ubuntu user has both read and write permissions to the contents. But when I try to start my Rails app I get permission errors on any files the app needs to write to (e.g. the log file) - why is that? Are there any major conceptual flaws with this approach? Would I be better off using the VBox "shared folders" function?

  Read the article

< Previous Page | 481 482 483 484 485 486 487 488 489 490 491 492  | Next Page >