Search Results

Search found 15558 results on 623 pages for 'basic authentication'.

Page 489/623 | < Previous Page | 485 486 487 488 489 490 491 492 493 494 495 496  | Next Page >

• Network Misconfiguration when adding first host to new vSphere cluster

  - by dunxd

  I am building a new vSphere cluster from scratch. I have installed ESXi on the first host, and built a vCenter server on a VM residing on that host (storage is on the local hard drive, although we have iSCSI targets which I can reach from the host). The cluster is configured for HA. When I try and add the host to the cluster, I get an error at the point where HA is configured - Cannot complete the . I have stripped the network configuration of the host down to the most basic - a single NIC attached to a single vSwitch - this is running the VMKernel Port on VLAN 8 - that is our Management VLAN. The vCenter server will have a network address on this VLAN, so I also set the initial Virtual Machine Port Group to this VLAN, and connected the vCenter server NIC to this port group. I understand I can't connect the vCenter server to the VMkernel port group, but shouldn't I be able to connect the vCenter server to a Port Group in the same VLAN? If not, do I need to create a VLAN specifically for VMKernel Port Group? I plan to set up another port group for vMotion with a dedicated and isolated VLAN (i.e. VLAN isn't routed) so this wouldn't allow vCenter to communicate. Does anyone have any suggestions, or other ideas for what might be causing the problem. I've read through the documentation, but it isn't giving me any pointers, and the error message isn't helping me beyond telling me something is wrong with my network config.

  Read the article

• Debootstrap Ubuntu over NFS leads to mknod I/O error

  - by Aaron B. Russell

  Hi everyone, I'm trying to prepare an Ubuntu environment for a diskless machine that will PXE boot and mount an NFS share as it's root. I've currently got another Ubuntu machine mounting the NFS share and I'm trying to debootstrap into it, but it has trouble creating devices over NFS: root@kimiko:~# mount | grep Seiuchi 192.168.0.203:/mnt/user/Seiuchi on /mnt type nfs (rw,addr=192.168.0.203) root@kimiko:~# debootstrap --arch i386 maverick /mnt http://gb.archive.ubuntu.com/ubuntu/ mknod: `/mnt/test-dev-null': Input/output error E: Cannot install into target '/mnt' mounted with noexec or nodev My NFS rule on the unRAID server is 192.168.0.201/32(rw,no_root_squash,sync). I don't have the noexec or nodev options set. I've not got much experience with NFS, so I'm probably missing something basic in the way I'm sharing this, but my attempts at Googling for an answer isn't really turning anything useful up. Does anyone have suggestions on what I might have missed or maybe relevant docs? Edit: Creating normal files (and directories) works just fine, I just can't create devices... root@kimiko:/mnt# mkdir foo root@kimiko:/mnt# cd foo root@kimiko:/mnt/foo# touch bar root@kimiko:/mnt/foo# mknod quux c 4 64 mknod: `quux': Input/output error root@kimiko:/mnt/foo# ls bar

  Read the article

• Xen domU passwd file overwritten with console log output

  - by malfy

  I was setting up a Debian Xen domU and after booting it fine, I added basic configuration to /etc/network/interfaces and ran /etc/init.d/networking restart. This failed so I decided to reboot. After the reboot I also ran xm shutdown box. When dropped to a shell prompt it wouldn't let me login. Upon further inspection, I now have garbage in some critical files in /etc: root@box:/# tail +1 mnt/etc/{passwd-,shadow} tail: cannot open `+1' for reading: No such file or directory ==> mnt/etc/passwd- <== 0000000000100000 (reserved) Nov 23 02:02:39 box kernel: [ 0.000000] Xen: 0000000000100000 - 0000000004000000 (usable) Nov 23 02:02:39 box kernel: [ 0.000000] DMI not present or invalid. Nov 23 02:02:39 box kernel: [ 0.000000] last_pfn = 0x4000 max_arch_pfn = 0x1000000 Nov 23 02:02:39 box kernel: [ 0.000000] initial memory mapped : 0 - 033ff000 Nov 23 02:02:39 box kernel: [ 0.000000] init_memory_mapping: 0000000000000000-0000000004000000 Nov 23 02:02:39 box kernel: [ 0.000000] NX (Execute Disable) protection: active Nov 23 02:02:39 box kernel: [ 0.000000] 0000000000 - 0004000000 page 4k Nov 23 02:02:39 box kernel: [ 0.000000] kernel direct mapping tables up to 4000000 @ 7000-2c000 Nov 23 02:02:3 ==> mnt/etc/shadow <== 32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1 Nov 23 02:02:39 box kernel: [ 0.000000] PERCPU: Embedded 15 pages/cpu @c15b0000 s37688 r0 d23752 u65536 Nov 23 02:02:39 box kernel: [ 0.000000] pcpu-alloc: s37688 r0 d23752 u65536 alloc=16*4096 Nov 23 02:02:39 box kernel: [ 0.000000] pcpu-alloc: [0] 0 Nov 23 02:02:39 box kernel: [ 0.000000] Xen: using vcpu_info placement Nov 23 02:02:39 box kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16160 Nov 23 02:02:39 box kernel: [ 0.000000] Kernel command line: root=/dev/mapper/xen-guest_root ro quiet root=/dev/xvda1 ro Nov 23 02:02:39 box kernel: [ 0.000000] PID hash table entries: The garbage is also present in the passwd file and the group file (although I didn't paste that above since I have since ran debootstrap on the filesystem again). Does anyone have any insight into what happened and why?

  Read the article

• Building a PC for Work and play? [closed]

  - by Derek Organ

  Ok, Its been a long time since I build my own PC so I'm looking to get back into it again and build a new one. First off budget is about €800 excluding the monitor and windows 7 licence and mouse. (just bought a new g500) I plan on using my computer for work, lots of applications open at once but none particularly excessive (photoshop being the most demanding, mostly coding tools) I also use it for some gaming, e.g. COD, Starcraft etc. One thing I do want to do eventually is get a really good monitor with hight resolution and maybe 27" so the graphics card needs to be able to make best use of that. So a few questions 1) Is the bottle neck in performance mostly still the harddrives? 2) Aren't most processors e.g. i5 etc even i3 so far a head of other bottlenecks it makes litte difference the higher you go. Isn't the Graphics card dealing with heavy graphics so what really slows because of a slow CPU? So from this my thinking is to get a SSD drive as my primary drive for OS etc and have loads of memory e.g. 6-8GB and a decent mid level graphics card? It doesn't seem at my level worth spending much on CPU and any other parts really. I basic parts off the top of my head Case, Motherboard CPU SSD Drive SATA Drive Power Supply Memory Cooling (fan?) Graphics Card Network Card Keyboard DVD drive Mouse Windows Monitor Am I missing anything? Any helpful tips or general education much appreciated. Thanks, Derek

  Read the article

• SSD Drive not being recongized in BIOS

  - by chobo2

  Well I bought my first drive Mushkin Chronos 180GB and got it installed in my computer and loaded up. I went to windows 7 and initialized the drive and then I installed "SSDlife Free" and loaded it up and my the SSD drive came up said it was "powered on 3 times"(thought it was odd but then thought maybe some testing???). I then restarted my computer and loaded into Acronis. Went to my SSD drive and make a partition called windows(made a basic logical partition). I then loaded up Norton ghost and wanted to copy my current windows onto the SSD drive on the partition I made found out I could not do it through the recovery disk so I made a backup of my windows drive and wanted to then restore it onto the SSD drive. Came back an hour later when the backup was done. I tried to restore the it on my SSD drive and could not find the partition so I loaded up Acronis again and it did not see it. I then went to the bios and saw only my other hard drive. What I tried Tried uplugging and replugging in both sata and power cables. Tried using the power and sata cable from the working drive and giving it the ones that SSD drive were using. Tried Sata AHCI Mode (Intel ICH9 Southbridge) Tried SATA PORT0-1 NATIVE MODE (Intel ICH9 Southbridge) Nothing worked. Software / hardware Windows 7 ultimate Gigabyte S-Series GA-P35-DS3L Mother board I hope someone has some ideas on why it is not being recognized.

  Read the article

• Nginx: Serve static files out of a given directory - one level too deep

  - by Joe J

  I'm pretty new to nginx configs. I'm having some difficulty with a pretty basic problem. I'd like to host some static files at /doc (index.html, some images, etc). The files are located in a directory called /sites/mysite/proj/doc/. The problem is, is that with the nginx config below, nginx tries to look for a directory called "/sites/mysite/proj/doc/doc". Perhaps this can be fixed by setting the root to /sites/mysite/proj/, but I don't want to potentially expose other (non-static) assets in the proj/ directory. And for various reasons, I can't really move the doc/ directory from where it is. I think there is a way to use a Rewrite rule to solve this situation, but I don't really understand all the parts, so having some difficulty formulating the rule. rewrite ^/doc/(.*)$ /$1 permanent; I've also included a working example of hosting files out of a /sites/mysite/htdocs/static/ directory. > vim locations.conf location /static { root /sites/mysite/htdocs/; access_log off; autoindex on; } location /doc { root /sites/mysite/proj/doc/; access_log on; autoindex on; } 2011/11/19 23:49:00 [error] 2314#0: *42 open() "/sites/mysite/proj/doc/doc" failed (2: No such file or directory), client: 100.100.100.100, server: , request: "GET /doc HTTP/1.1", host: "myhost.com" Does anyone have any ideas how I might go about serving this static content? Any help is much appreciated. Thanks, Joe

  Read the article

• PC won't PXE boot to WDS/MDT with Dell Optiplex 755

  - by Moman10

  I am trying to set up a basic MDT solution. I have set one up in the past at a previous job and it worked flawlessly, however here I'm running into a problem and am having no luck getting around it. I've installed Windows Server 2012 and MDT 2013, along with adding on the WDS role. I haven't configured much outside of the defaults for WDS, basically just set PXE response to respond to all clients (and unchecked admin approval). This machine does not run a DHCP server. I looked on the DHCP scope of our DHCP server, it shows options 66/67 checked and the server name of the WDS server is in there as well. I didn't add this but I assume it was put on during the install process (I believe I had to manually make some adjustments at my old job for this). The PC I have is a Dell Optiplex 755. I have enabled the onbard NIC w/PXE boot option in BIOS and attempted to boot. I get a "TFTP...." error but nothing offering out a DHCP address like I'm used to. In my previous job it pretty much worked right out of the box. I've verified that PortFast is enabled on the port and I've tried a couple different PCs (but both are the same model, only model I have to work with). No matter what, I get the same error. The subnet the PC is in is a different subnet than where the WDS server is sitting, but there are IP helper statements on the switch and the PCs can get regular DHCP addresses just fine from the DHCP server, just doesn't seem to get offered out a PXE boot option. I don't know if the problem is a configuration with the server or the PC itself...but after a few days of Googling I'm running out of ideas. Does anyone have a good idea of something it may be?

  Read the article

• Windows 7 Aero theme's "greyed out" - no found fix

  - by Robsta

  Brand new machine that was working fine then randomly it changed the theme when I booted into a sort of "basic" theme (white task bar, no see through windows etc) I've done and attempted many fixes and I still don't understand why it doesn't work. I've tried these two solutions: "How to enable Windows 7 Aero Theme" and "Windows 7 Aero Themes Greyed out" These solutions included registy changes, stopping/starting services, and force starting the aero theme. The closest I got seems to be when I went into: Control panel (category view) Find and fix problems (System and Security) Display Aero Desktop Effects I follow through the wizard and let it do its thing and then I get an error window that pops up: Personalization - "This theme can't be applied to the desktop. Try clicking a diffrent theme." That's what I get from the wizard. What can I do? My drivers are all up to date, there are no viruses on the computer, directx is installed and updated, and the registry is all correct. EDIT: When I boot the computer, I get a notification stating that windows failed to communicate with the windows desktop services.

  Read the article

• Building a Web proxy to get around same-origin restrictions for collaborative Webapp based on a MEAN stack

  - by Lew Cohen

  Can anyone point to books, articles, blogs, or even applications - open-source or proprietary - that detail building a Web proxy? This specific proxy will exist to get around the same-origin restrictions that prevent, for instance, loading a given Website into an <iframe> in a Webapp. This Webapp is a collaborative application in which a group of users log in to the app's Website and can then load different Websites into this app's <iframe> and do various collaborative things (e.g., several users simultaneously browsing a Website, in synch). The Webapp itself is built on a MEAN stack (MongoDB, Express, AngularJS, and Node.js). The purpose of this proxy is not to do anonymous browsing or to bypass censorship. Information on how to build such a vehicle seems not to be readily available from my research. I've come across Glype but am not sure whether this is a feasible solution. I don't want to reinvent the wheel, so if a product is available for purchase, great. Else, we'd need to build one. The one that seems to be close is http://www.corsproxy.com. In effect, we'd like to re-create this since it evidently does what's needed. I don't care what server-side technology is used. Our app is MEAN-based, if that has any bearing. Also, the proxy has to obviously honor basic security considerations (user cookies, etc.) and eventually be scalable. So, anyone know of any sources that would detail how to build one of these? Is it even worth building if something already exists? If so, what would be a good candidate? Any other issues that should be considered with this proxy/application? Thanks a lot!

  Read the article

• Parsing text files

  - by d03boy

  I encountered a situation tonight where I wanted to parse a text file. I had a very, very long word list that contained English words delimited by lines. I wanted to get rid of every word (or line) that was longer than 7 characters. This would be simple in Linux but I can't seem to find a simple solution in WindowsXP. I tried using Notepad++ regular expression search but that was a huge failure. I tried using the expression .{6,} without finding any matches. I'm really at a loss because I thought this sort of thing would be extremely easy and there would be tons of tools to accomplish a task like this. It seems like Notepad++ supports every other feature in the world except the very basic ones that seem the most obvious. Another one of my goals was to put some code before and after the word on each line. aardvark apple azolio would turn into INSERT INTO Words (word) VALUES ('aardvark'); INSERT INTO Words (word) VALUES ('apple'); INSERT INTO Words (word) VALUES ('azolio'); What suggestions/tools/tips do you have to accomplish tasks similar to this in WindowsXP?

  Read the article

• Apache ScriptAlias and access error?

  - by Parhs

  First of all after much pain i figured out how to make it work in Apache 2.4 windowz. Here is my configuration that seems to work successfully for git clone and push and everything. Problem First of all my configuration works. There is a "Require all denied" at / directory. I want only git functionality and nothing else. Example Request from a git client 192.168.100.252 - - [07/Oct/2012:04:44:51 +0300] "GET /git/simple/info/refs?service=git-upload-pack HTTP/1.1" 200 264` Error caused by that Request [Sun Oct 07 04:44:51.903334 2012] [authz_core:error] [pid 6988:tid 956] [client 192.168.100.252:13493] AH01630: client denied by server configuration: C:/git-server/web/simple There isnt any error at gitclient everything works fine but i get this at error log. Is there any solution for this error to not appear?I worry about log size. <VirtualHost *:80> DocumentRoot "C:\git-server\web" ServerName git.****censored**** DirectoryIndex index.php SetEnv GIT_PROJECT_ROOT c:/git-server/repositories SetEnv GIT_HTTP_EXPORT_ALL SetEnv REMOTE_USER=$REDIRECT_REMOTE_USER ScriptAlias /git/ "C:/Program Files (x86)/Git/libexec/git-core/git-http-backend.exe/" <LocationMatch "^/.*/git-receive-pack$"> Options +ExecCGI AuthType Basic AuthName intranet AuthUserFile "C:/git-server/config/users" Require valid-user </LocationMatch> <Directory /> Options All Require all denied </Directory> <Directory "C:\Program Files (x86)\Git\libexec\git-core"> Options +ExecCGI Options All Require all granted </Directory> </VirtualHost>

  Read the article

• php_ibm_db2.dll on IIS 7.5 using PHP 5.3 error message

  - by grmbl

  I'm trying to use ibm_db2 extension to access iSeries DB2 database. This is the testcode (taken from here) <?php $database = 'ALI452BFAL'; //library $user = 'STN452'; $password = '**********'; $hostname = 'myserverip'; $port = 50000; $conn_string = "DRIVER={IBM DB2 ODBC DRIVER};DATABASE=$database;" . "HOSTNAME=$hostname;PORT=$port;PROTOCOL=TCPIP;UID=$user;PWD=$password;"; $conn = db2_connect($conn_string, '', ''); if ($conn) { print "ok"; db2_close($conn); } else { echo db2_conn_error() . '<br>' . db2_conn_errormsg(); } ?> I have installed a very basic package containing the db2 driver and added this as an extension. (IBM Data Server Driver for ODBC, CLI, and .NET.msi) This is my result: 08001 [IBM][CLI Driver] SQL30081N A communication error has been detected. Communication protocol being used: "TCP/IP". Communication API being used: "SOCKETS". Location where the error was detected: "10.10.0.120". Communication function detecting the error: "connect". Protocol specific error code(s): "10061", "", "". SQLSTATE=08001 SQLCODE=-30081 Anybody tried this before??

  Read the article

• Password Protect XML-RPC

  - by Terence Eden

  I have a service running on a server which I want to access via XML-RPC. I've installed all the necessary bits. Within /etc/apache2/httpd.conf I have the single line SCGIMount /RPC2 127.0.0.1:5000 I can run xmlrpc commands from my server - and any server which connects to /RPC2. What I want to do is password protect the directory to stop unauthorised usage. Within /etc/apache2/httpd.conf I've added <Location /RPC2> AuthName "Private" AuthType Basic AuthBasicProvider file AuthUserFile /home/me/myhtpasswd Require user me </Location> Trying to access /RPC2 brings up the "Authorization Required" box and it accepts my username and password. However, xmlrpc now doesn't work! If I run xmlrpc localhost some_command on my server, I get the error Failed. Call failed. HTTP response code is 401, not 200. (XML-RPC fault code -504) Is there any way I can password protect my /RPC2 directory and have xmlrpc commands work?

  Read the article

• Linux DHCPD Mac-Address based Groups

  - by GruffTech

  Our Current DHCPD.conf looks like the following. subnet 10.0.32.0 netmask 255.255.255.0 { range 10.0.32.100 10.0.32.254; option subnet-mask 255.255.255.0; option broadcast-address 10.0.32.255; option domain-name-servers 208.67.222.222,208.67.220.220; option routers 10.0.32.5; host Dev-ABaird-W { hardware ethernet 00:1D:09:3E:49:13; fixed-address 10.0.32.94; } ... more static hosts .... } About as basic as it gets. The old router is 10.0.32.1, our company wanted to implement a squid proxy to better monitor web traffic while at work, and if necessary block large time-wasters, IE Facebook.com. However, we've quickly realized that this change has played a mean prank on our Polycom SIP Phones. Occasionally our phones will not ring, the end recipient hears ringing (this is artificially created by our PBX) however the handset never rings. The ONLY thing that has changed in our network is the option routers line. So, Since all Polycom MAC addresses begin with 00:04:F2 would it be possible in DHCP to say any 00:04:F2:::* MAC addresses get option routers 10.0.32.1, and anything else must talk with our Gateway?

  Read the article

• What could cause TFTP reloaded Cisco `running-config` on 871 to fail?

  - by xtian

  Cisco CCP Write Configuration borked my 871w config while I was trying to setup port forwarding. I went through the basic steps to reconfig the router. I looked to see if I could just reset the router. Nope. I tested the 871's flash memory with fsck to see if there was hardware failure. Nope. Then I rewrote the minimal config for TFTP (which is the same for Cisco's CCP app.). Thne, I successfully uploaded a previously working running-config from Win Vista using SolarWinds TFTP Server, unfortunately the restore was not entirely successful. The old running config was saved to the 871's startup-config and I can login using console port. Some other things that are working are the hostname and welcome message but that's about it. Startup shows an error SETUP: new interface NVI0 placed in "shutdown" state after tftp. The missing light on the access point modem for ethernet link show the 871'a outside FE4 is not working. SO...what's the possible problem with reloading a previously working config (approximately 4 months with the same config) via TFTP? Is there something I can look for on the 871 to verify the config? Or on Vista to validate the config file itself before I transfer it? Or, is this there a common TFTP issue? UPDATE. I missed the instruction from Cisco's TFTP page to delete aaa lines from the config (although a video from a SuperUser user didn't make this point in his most excellent demo). There were several lines of this sort, I deleted them and uploaded again. However, they're back. I assume they're added automatically? [nope, see answer] UPDATE 2. The reload of previous settings was successful, but this error remains. I don't even know now if it was there before or not. It seems irrelevant to the question.

  Read the article

• Backing up SQL NetApp Snapshots using TSM

  - by WerkkreW

  In our environment we have a 3 node SQL 2005 Cluster which is on NetApp storage. We are currently using SMSQL (NetApp SnapManager for SQL) to take Snapshot backups of the data. This works great, but due to some audit requirements we are also forced to maintain some copies on tape. We have used NDMP in other places across the enterprise but we do not want to use it in this specific instance. Basically what I need to do is, get the most recent snapshot copy of the databases on tape, via Tivoli Storage Manager (TSM). What I have done is, obtained a basic Windows Server 2003 VM with SnapDrive installed, which is SAN attached and zoned to the NetApp, and I have written a batch file to do the following: Mount the latest __RECENT snapshot lun to the host, using a specific drive letter Perform a TSM based incremental backup Dis-mount the LUN This seems to work fine, except sometimes the LUN's do not mount due to some sort of timeout. Also, due to my limited knowledge of windows batch scripting, I have no way to monitor the success or failure of these backups since I do not know how to send a valid return code back to the TSM scheduling service. Is there a more efficient/elegant way to accomplish this without NDMP?

  Read the article

• How to grant read/write to specific user in any existent or future subdirectory of a given directory? [migrated]

  - by Samuel Rossille

  I'm a complete newbie in system administration and I'm doing this as a hobby. I host my own git repository on a VPS. Let's say my user is john. I'm using the ssh protocol to access my git repository, so my url is something like ssh://[email protected]/path/to/git/myrepo/. Root is the owner of everything that's under /path/to/git I'm attempting to give read/write access to john to everything which is under /path/to/git/myrepo I've tried both chmod and setfacl to control access, but both fail the same way: they apply rights recursively (with the right options) to all the current existing subdirectories of /path/to/git/myrepo, but as soon as a new directory is created, my user can not write in the new directory. I know that there are hooks in git that would allow me to reapply the rights after each commit, but I'm starting to think that i'm going the wrong way because this seems too complicated for a very basic purpose. Q: How should I setup my right to give rw access to john to anything under /path/to/git/myrepo and make it resilient to tree structure change ? Q2: If I should take a step back change the general approach, please tell me.

  Read the article

• 1and1 ssh - connection refused

  - by kitensei

  I'm having troubles connecting through SSH to my 1&1 account. When I try to connect with command userXXX@host -p22 -vv I have the following output: OpenSSH_5.8p1 Debian-7ubuntu1, OpenSSL 1.0.0e 6 Sep 2011 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to mySite.com [ip_here] port 22. debug1: connect to address ip_here port 22: Connection refused Moreover, once I try to connect through SSH and it fails, even the HTTP access is dead, I cannot access the website through explorer anymore :/ please help < I'm running ubuntu 11.10 EDIT: don't know if it can help, here's the .htaccess of the 1and1 server Options +Indexes Satisfy any Order Deny,Allow Allow from 212.227.X.X Deny from all RemoveType .html .gif AuthType Basic AuthName "Access to /logs" AuthUserFile /kunden/homepages/43/d376072470/htpasswd Require user "user_here" and sftp.log: Mar 26 09:21:24 193.251.X USER_HERE Connection from 193.251.X port 51809 Mar 26 09:21:30 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:39 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:41 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:45 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:57 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 10:53:36 212.227.X tmp64459736-3228 Connection from 212.227.X port 23275 Mar 26 10:53:36 212.227.X tmp64459736-3228 Accepted password for tmp64459736-3228 from 212.227.X port 23275 ssh2 Mar 26 11:53:37 212.227.X tmp64459736-3228 Connection closed by 212.227.X Mar 26 18:58:17 212.227.X tmp64459736-5363 Connection from 212.227.X port 23353 Mar 26 18:58:17 212.227.X tmp64459736-5363 Accepted password for tmp64459736-5363 from 212.227.X port 23353 ssh2 Mar 26 19:53:36 212.227.X tmp64459736-8525 Connection from 212.227.X port 5166 Mar 26 19:53:36 212.227.X tmp64459736-8525 Accepted password for tmp64459736-8525 from 212.227.X port 5166 ssh2 Mar 26 19:58:17 212.227.X tmp64459736-5363 Connection closed by 212.227.X

  Read the article

• Jenkins CI - Cannot allocate memory

  - by Programmieraffe

  I tested jenkins-ci successfully on a ubuntu 10.4 (with vmware fusion) on my local computer. Now I want to install and use it on my virtual server at hosteurope. The basic installation was no problem, but now I have problems with my build project. After pulling an mercurial update from a repository, ant is invoked and throws the following error in my build project: "Buildfile: /var/lib/jenkins/workspace/concrete5-seed-clean/build.xml [property] java.io.IOException: Cannot run program "/usr/bin/env": java.io.IOException: error=12, Cannot allocate memory" There is a known problem with heap size at virtual servers at hosteurope (http://faq.hosteurope.de/index.php?cpid=13918), so I tried to set the heap size manually: # for ant export ANT_OPTS="-Xms512m -Xmx512m" # jenkins # edited /etc/default/jenkins, added line JAVA_ARGS="-Xms512m -Xmx512m" # restarted jenkins via /etc/init.d/jenkins restart After setting this for ant, the command "ant -diagnostics" runs through and does not cause an error, but the error still occurs when I try to build the project. Server-Details: - http://www.hosteurope.de/produkt/Virtual-Server-Linux-L Ubuntu 10.4 LTS RAM: 1GB / Dynamic 2GB My questions: - Is 1GB enough for Jenkins or do I have to upgrade the server? - Is this error caused by ant or jenkins? Update: I got it running with ant options -Xmx128m -Xms128m, but sometimes the error occurs again. (this freaks me out, cause i can not reproduce it by now :/ ) Help much appreciated! Cheers, Matthias

  Read the article

• Troubleshoot dropped wireless connections

  - by Jack

  I was recently hired in the IT department of a small company (~180 users) and one of the issues that people have been complaining about is having their wi-fi connections drop during meetings. The company is using an HP ProCurve Wireless LAN with 10 APs and a controller unit located in the server room. I don't have any experience troubleshooting WLAN in a multi-AP environment, so I'm trying to at least gather information using free or cheap tools. I did a basic site survey using the free version of Ekahau HeatMapper and discovered the following in one of the conference rooms that has been a problem. The program picked up three access points (plus a bunch of others with much lower signals that were out of range): AP 1: SSID: "Unknown SSID" - Signal strength: -48 dBm - -40 dBm. Channel: 2 AP 2: SSID "CompanyMain" - Signal strength: -35 dBm or greater. Channel: 2. Security: WEP (This is the main SSID for the company's WLAN.) AP 3: SSID: "CompanyGuest" - Signal strength: -40 dBm - -35 dBm. Channel: 2. Security: WPA2 (This SSID is the company's "guest" WLAN, which was setup to allow Internet access, but prevent network access.) Is there anything that you see that is clearly a problem from the above? I'm assuming that the unknown SSID might be a big problem, and that it is an AP from a neighboring office that is causing interference. Does that seem likely? Also, regarding channel, should we try changing the channels of our APs to avoid interference with that unknown SSID? (Since everything seems to be on Channel 2?) Should our APs be on different channels? In other words, should the CompanyMain and CompanyGuest APs be on different channels? Finally, any recommendations for free/cheap tools to help me figure this out, and/or a good methodology to follow? Thanks in advance for any help. Jack

  Read the article

• GeekTool logs "command not found" for commands that work fine in Terminal

  - by Kevin Dowling

  I'm trying to run simple commands so I can have GeekTool output date/time etc. to my desktop. Should be simple enough to do but it never actually outputs anything into the boxes. Console log shows it's getting spammed by GeekTool to say 'command not found', though the same command (e.g. date +"%H:%M") works fine in Terminal. All I want to achieve is the ability to output a clock displaying time/date on my desktop that fits into my wallpaper. I've tried changing the format of the commands, using the built-in editor window as well as the command line box on the Properties tab. I had a look at the permissions in '/' (because GeekTool runs commands from there) and nothing unusual comes up. None of these solved the issue. When I use a command that simply echo's a string it works (e.g. echo "hello" displays the word hello). Does anyone have experience with GeekTool, and understand why it won't run basic commands? As I say, it's spamming my console with 'command not found' despite them working in terminal... Running OS X 10.6.6 on a MacBook Pro (mid-2010).

  Read the article

• What ways are there to set permissions on an Exchange 2003 mailbox?

  - by HopelessN00b

  I'm having a difficult/impossible time tracing down a permissions issue on an Exchange 2003 mailbox, and I was wondering if I'm missing any technical possibilities here. The basic question is what ways are there to set a user's permissions to access a mailbox in Exchange 2003? I know of two. Permissions on the mailbox itself (Mailbox Rights) and having delegated rights. And then, if it's possible, how would one view all the permissions (including delegated permissions) on the mailbox? The situation is that a new user who's been set up "exactly like all the others" in his department (pretty sure he was copied via the right click option in ADUC, in fact) can't access a specific shared mailbox, which I've been assured about a dozen other people do have access to and access on a regular basis. As to how they got permissions to the mailbox, no one knows, so it must have been granted by a white wizard whose spell has since worn off, so now IT has to handle it instead. Anyway... This mailbox is a normal AD user, created as a service account, for which no one knows the password (of course), so it's probably not the case that this service account was being used to delegate permissions. Upon taking examining the Mailbox Rights directly... Here are the permissions I see: This leads me to believe that one of two things are happening - the managers have been delegating full mailbox permissions to the rest of the department, or everyone's logging in using... not their own account. But, before I get too excited about the prospect of busting out the LART and strolling over to that department, I want to make sure I'm not missing another possible explanation. Like most of the rest of the world, I ditched Exchange 2003 at the earliest possible opportunity, and had been looking forward to never seeing it again, so I'm a bit rusty on the intricacies of how it [mostly, sort of] works. Anyone see any or possibilities, or things I may have missed, or does the LART get to come out and play?

  Read the article

• fail2ban block ports rules iptable

  - by J Spen

  I just installed Ubuntu Server 14.04 and don't have much experience with IPtables. I am trying to get a basic setup going where I only accept SSH connections on port 22 and 2222. I actually have that working with no problem using fail2ban ssh. Then I wanted to block all other ports except 423 and 4242 but either method of DROPing all connections that are not listed seems not to work and it blocks me out of everything. Below is the setup that works: -P INPUT ACCEPT -P FORWARD ACCEPT -P OUTPUT ACCEPT -N fail2ban-ssh -A INPUT -p tcp -m multiport --dports 22,2222 -j fail2ban-ssh -A fail2ban-ssh -j RETURN I tried to change it either to: -P INPUT DROP -P FORWARD ACCEPT -P OUTPUT ACCEPT -N fail2ban-ssh -A INPUT -p tcp -m multiport --dports 22,2222 -j fail2ban-ssh -A fail2ban-ssh -j RETURN or: -P INPUT ACCEPT -P FORWARD ACCEPT -P OUTPUT ACCEPT -N fail2ban-ssh -A INPUT -p tcp -m multiport --dports 22,2222 -j fail2ban-ssh -A INPUT -j DROP -A fail2ban-ssh -j RETURN I have noticed that the rules for fail2ban-ssh are automatically added to my iptables on boot because if I save them with iptables-persistant they are entered twice. How do I go about blocking everything accept those 2 ports using fail2ban? Is it a bad fail2ban configuration or do I need to add the fail2ban-ssh -j Return somewhere else in my code.

  Read the article

• Trying to run a codeigniter app on custom php

  - by hamstar

  I have a CodeIgniter app that I deployed to a server with php 5.2 and my dev box has 5.3, and some stuff doesn't work anymore. I didn't want to upgrade php and risk the other app on the server having issues. Anyway I compiled a custom PHP and added the following to a single .conf file in /etc/httpd/conf.d/zcid.conf with all the other conf files. <VirtualHost *:80> DocumentRoot /var/www/cid/app ServerName sub.example.co.nz </VirtualHost> <Directory "/var/www/cid/app"> authtype Basic authname "oh dear how did this get here i am no good with computer" authuserfile /path/to/auth require valid-user RewriteEngine on RewriteCond $1 !^(index\.php|robots\.txt|createEvent\.php|/cgi-bin) RewriteRule ^(.*)$ /index.php/$1 [L] AddHandler custom-php .php Action custom-php /cgi-bin/php53.cgi </Directory> In /var/www/cid/app I have the cgi-bin folder and the php53.cgi that I copied from /usr/local/php53/bin/php-cgi But now when I navigate to the subdomain it says: The requested URL /cgi-bin/php53.cgi/index.php/ was not found on this server. And if I try to browse to /cgi-bin it says (what it is supposed to?): You don't have permission to access /cgi-bin/ on this server. Quite confused now. Anyone know what to do here? Thanks :)

  Read the article

• Resize a RAID 1 volume on OS X Snow Leopard - how? (Note: software raid)

  - by Emmel

  I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OS X 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

  Read the article

< Previous Page | 485 486 487 488 489 490 491 492 493 494 495 496  | Next Page >